| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As it turns out, vendor HDMI PHY driver for H6 has a pretty big table
of predefined values for various pixel clocks. However, most of them are
not useful/tested because they come from reference driver code. Vendor
PHY driver is concerned with only few of those, namely 27 MHz, 74.25
MHz, 148.5 MHz, 297 MHz and 594 MHz. These are all frequencies for
standard CEA modes.
Fix sun50i_h6_cur_ctr and sun50i_h6_phy_config with the values only for
aforementioned frequencies.
Table sun50i_h6_mpll_cfg doesn't need to be changed because values are
actually frequency dependent and not so much SoC dependent. See i.MX6
documentation for explanation of those values for similar PHY.
Fixes: c71c9b2fee17 ("drm/sun4i: Add support for Synopsys HDMI PHY")
Tested-by: Andre Heider <[email protected]>
Signed-off-by: Jernej Skrabec <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
As expected, HDMI controller clock should always match pixel clock. In
the past, changing HDMI controller rate would seemingly worsen
situation. However, that was the result of other bugs which are now
fixed.
Fix that by removing set_rate quirk and always set clock rate.
Fixes: 40bb9d3147b2 ("drm/sun4i: Add support for H6 DW HDMI controller")
Reviewed-by: Chen-Yu Tsai <[email protected]>
Tested-by: Andre Heider <[email protected]>
Signed-off-by: Jernej Skrabec <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Channel 1 has polarity bits for vsync and hsync signals but driver never
sets them. It turns out that with pre-HDMI2 controllers seemingly there
is no issue if polarity is not set. However, with HDMI2 controllers
(H6) there often comes to de-synchronization due to phase shift. This
causes flickering screen. It's safe to assume that similar issues might
happen also with pre-HDMI2 controllers.
Solve issue with setting vsync and hsync polarity. Note that display
stacks with tcon top have polarity bits actually in tcon0 polarity
register.
Fixes: 9026e0d122ac ("drm: Add Allwinner A10 Display Engine support")
Reviewed-by: Chen-Yu Tsai <[email protected]>
Tested-by: Andre Heider <[email protected]>
Signed-off-by: Jernej Skrabec <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
We don't have a persistent fb holding a reference to the frontbuffer
object, so every time we do the get+put we throw the frontbuffer object
immediately away. And so the next time around we get a pristine
frontbuffer object with bits==0 even for the old vma. This confuses
the frontbuffer tracking code which understandably expects the old
frontbuffer to have the overlay's bit set.
Fix this by hanging on to the frontbuffer reference until the next
flip. And just to make this a bit more clear let's track the frontbuffer
explicitly instead of just grabbing it via the old vma.
Cc: [email protected]
Cc: Chris Wilson <[email protected]>
Cc: Joonas Lahtinen <[email protected]>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1136
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Fixes: 8e7cb1799b4f ("drm/i915: Extract intel_frontbuffer active tracking")
Reviewed-by: Chris Wilson <[email protected]>
(cherry picked from commit 553c23bdb4775130f333f07a51b047276bc53f79)
Signed-off-by: Jani Nikula <[email protected]>
|
|
This reverts commit 4a3dea8932d3b1199680d2056dd91d31d94d70b7.
This causes blank screens for some users.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1482
Cc: Alvin Lee <[email protected]>
Cc: Jun Lei <[email protected]>
Cc: Rodrigo Siqueira <[email protected]>
Reviewed-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2021-02-10
The following pull-request contains BPF updates for your *net* tree.
We've added 5 non-merge commits during the last 8 day(s) which contain
a total of 3 files changed, 22 insertions(+), 21 deletions(-).
The main changes are:
1) Fix missed execution of kprobes BPF progs when kprobe is firing via
int3, from Alexei Starovoitov.
2) Fix potential integer overflow in map max_entries for stackmap on
32 bit archs, from Bui Quang Minh.
3) Fix a verifier pruning and a insn rewrite issue related to 32 bit ops,
from Daniel Borkmann.
====================
Signed-off-by: David S. Miller <[email protected]>
c# Please enter a commit message to explain why this merge is necessary,
|
|
Fixes small regression in implementation of new mount API.
Signed-off-by: Ronnie Sahlberg <[email protected]>
Reported-by: Hyunchul Lee <[email protected]>
Tested-by: Hyunchul Lee <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
This reverts commit 536d3bf261a2fc3b05b3e91e7eef7383443015cf, as it can
cause writers to memory.high to get stuck in the kernel forever,
performing page reclaim and consuming excessive amounts of CPU cycles.
Before the patch, a write to memory.high would first put the new limit
in place for the workload, and then reclaim the requested delta. After
the patch, the kernel tries to reclaim the delta before putting the new
limit into place, in order to not overwhelm the workload with a sudden,
large excess over the limit. However, if reclaim is actively racing
with new allocations from the uncurbed workload, it can keep the write()
working inside the kernel indefinitely.
This is causing problems in Facebook production. A privileged
system-level daemon that adjusts memory.high for various workloads
running on a host can get unexpectedly stuck in the kernel and
essentially turn into a sort of involuntary kswapd for one of the
workloads. We've observed that daemon busy-spin in a write() for
minutes at a time, neglecting its other duties on the system, and
expending privileged system resources on behalf of a workload.
To remedy this, we have first considered changing the reclaim logic to
break out after a couple of loops - whether the workload has converged
to the new limit or not - and bound the write() call this way. However,
the root cause that inspired the sequence change in the first place has
been fixed through other means, and so a revert back to the proven
limit-setting sequence, also used by memory.max, is preferable.
The sequence was changed to avoid extreme latencies in the workload when
the limit was lowered: the sudden, large excess created by the limit
lowering would erroneously trigger the penalty sleeping code that is
meant to throttle excessive growth from below. Allocating threads could
end up sleeping long after the write() had already reclaimed the delta
for which they were being punished.
However, erroneous throttling also caused problems in other scenarios at
around the same time. This resulted in commit b3ff92916af3 ("mm, memcg:
reclaim more aggressively before high allocator throttling"), included
in the same release as the offending commit. When allocating threads
now encounter large excess caused by a racing write() to memory.high,
instead of entering punitive sleeps, they will simply be tasked with
helping reclaim down the excess, and will be held no longer than it
takes to accomplish that. This is in line with regular limit
enforcement - i.e. if the workload allocates up against or over an
otherwise unchanged limit from below.
With the patch breaking userspace, and the root cause addressed by other
means already, revert it again.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 536d3bf261a2 ("mm: memcontrol: avoid workload stalls when lowering memory.high")
Signed-off-by: Johannes Weiner <[email protected]>
Reported-by: Tejun Heo <[email protected]>
Acked-by: Chris Down <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Cc: Roman Gushchin <[email protected]>
Cc: Shakeel Butt <[email protected]>
Cc: Michal Koutný <[email protected]>
Cc: <[email protected]> [5.8+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Update my email, @virtuozzo.com will stop working shortly.
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Andrey Ryabinin <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Commit c2aa8afc36fa has renamed run_vmtests in Makefile, but the file
still uses the old name.
The kernel test robot reported the following issue:
# selftests: vm: run_vmtests.sh
# Warning: file run_vmtests.sh is missing!
not ok 1 selftests: vm: run_vmtests.sh
Link: https://lkml.kernel.org/r/[email protected]
Fixes: c2aa8afc36fa (selftests/vm: rename run_vmtests --> run_vmtests.sh)
Signed-off-by: Rong Chen <[email protected]>
Reported-by: kernel test robot <[email protected]>
Reviewed-by: John Hubbard <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
As with s390, alpha is a 64-bit architecture with a 32-bit ino_t. With
CONFIG_TMPFS_INODE64=y tmpfs mounts will get 64-bit inode numbers and
display "inode64" in the mount options, whereas passing "inode64" in the
mount options will fail. This leads to erroneous behaviours such as
this:
# mkdir mnt
# mount -t tmpfs nodev mnt
# mount -o remount,rw mnt
mount: /home/ubuntu/mnt: mount point not mounted or bad option.
Prevent CONFIG_TMPFS_INODE64 from being selected on alpha.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: ea3271f7196c ("tmpfs: support 64-bit inums per-sb")
Signed-off-by: Seth Forshee <[email protected]>
Acked-by: Hugh Dickins <[email protected]>
Cc: Chris Down <[email protected]>
Cc: Amir Goldstein <[email protected]>
Cc: Richard Henderson <[email protected]>
Cc: Ivan Kokshaysky <[email protected]>
Cc: Matt Turner <[email protected]>
Cc: <[email protected]> [5.9+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Currently there is an assumption in tmpfs that 64-bit architectures also
have a 64-bit ino_t. This is not true on s390 which has a 32-bit ino_t.
With CONFIG_TMPFS_INODE64=y tmpfs mounts will get 64-bit inode numbers
and display "inode64" in the mount options, but passing the "inode64"
mount option will fail. This leads to the following behavior:
# mkdir mnt
# mount -t tmpfs nodev mnt
# mount -o remount,rw mnt
mount: /home/ubuntu/mnt: mount point not mounted or bad option.
As mount sees "inode64" in the mount options and thus passes it in the
options for the remount.
So prevent CONFIG_TMPFS_INODE64 from being selected on s390.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: ea3271f7196c ("tmpfs: support 64-bit inums per-sb")
Signed-off-by: Seth Forshee <[email protected]>
Acked-by: Hugh Dickins <[email protected]>
Cc: Chris Down <[email protected]>
Cc: Hugh Dickins <[email protected]>
Cc: Amir Goldstein <[email protected]>
Cc: Heiko Carstens <[email protected]>
Cc: Vasily Gorbik <[email protected]>
Cc: Christian Borntraeger <[email protected]>
Cc: <[email protected]> [5.9+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
clang can't evaluate this function argument at compile time when the
function is not inlined, which leads to a link time failure:
ld.lld: error: undefined symbol: __compiletime_assert_414
>>> referenced by mremap.c
>>> mremap.o:(get_extent) in archive mm/built-in.a
Mark the function as __always_inline to avoid it.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 9ad9718bfa41 ("mm/mremap: calculate extent in one place")
Signed-off-by: Arnd Bergmann <[email protected]>
Tested-by: Nick Desaulniers <[email protected]>
Reviewed-by: Nathan Chancellor <[email protected]>
Tested-by: Sedat Dilek <[email protected]>
Cc: Kirill A. Shutemov" <[email protected]>
Cc: Wei Yang <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: Dmitry Safonov <[email protected]>
Cc: Brian Geffon <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
arm64 references the start address of .builtin_fw (__start_builtin_fw)
with a pair of R_AARCH64_ADR_PREL_PG_HI21/R_AARCH64_LDST64_ABS_LO12_NC
relocations. The compiler is allowed to emit the
R_AARCH64_LDST64_ABS_LO12_NC relocation because struct builtin_fw in
include/linux/firmware.h is 8-byte aligned.
The R_AARCH64_LDST64_ABS_LO12_NC relocation requires the address to be a
multiple of 8, which may not be the case if .builtin_fw is empty.
Unconditionally align .builtin_fw to fix the linker error. 32-bit
architectures could use ALIGN(4) but that would add unnecessary
complexity, so just use ALIGN(8).
Link: https://lkml.kernel.org/r/[email protected]
Link: https://github.com/ClangBuiltLinux/linux/issues/1204
Fixes: 5658c76 ("firmware: allow firmware files to be built into kernel image")
Signed-off-by: Fangrui Song <[email protected]>
Reported-by: kernel test robot <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Reviewed-by: Nick Desaulniers <[email protected]>
Tested-by: Nick Desaulniers <[email protected]>
Tested-by: Douglas Anderson <[email protected]>
Acked-by: Nathan Chancellor <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Currently, whether the alloc/free stack traces collection is enabled by
default for hardware tag-based KASAN depends on CONFIG_DEBUG_KERNEL.
The intention for this dependency was to only enable collection on slow
debug kernels due to a significant perf and memory impact.
As it turns out, CONFIG_DEBUG_KERNEL is not considered a debug option
and is enabled on many productions kernels including Android and Ubuntu.
As the result, this dependency is pointless and only complicates the
code and documentation.
Having stack traces collection disabled by default would make the
hardware mode work differently to to the software ones, which is
confusing.
This change removes the dependency and enables stack traces collection
by default.
Looking into the future, this default might makes sense for production
kernels, assuming we implement a fast stack trace collection approach.
Link: https://lkml.kernel.org/r/6678d77ceffb71f1cff2cf61560e2ffe7bb6bfe9.1612808820.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <[email protected]>
Reviewed-by: Marco Elver <[email protected]>
Cc: Catalin Marinas <[email protected]>
Cc: Vincenzo Frascino <[email protected]>
Cc: Dmitry Vyukov <[email protected]>
Cc: Alexander Potapenko <[email protected]>
Cc: Will Deacon <[email protected]>
Cc: Andrey Ryabinin <[email protected]>
Cc: Peter Collingbourne <[email protected]>
Cc: Evgenii Stepanov <[email protected]>
Cc: Branislav Rankov <[email protected]>
Cc: Kevin Brodsky <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Sysbot has reported a warning where a kmalloc() attempt exceeds the
maximum limit. This has been identified as corruption of the xattr_ids
count when reading the xattr id lookup table.
This patch adds a number of additional sanity checks to detect this
corruption and others.
1. It checks for a corrupted xattr index read from the inode. This could
be because the metadata block is uncompressed, or because the
"compression" bit has been corrupted (turning a compressed block
into an uncompressed block). This would cause an out of bounds read.
2. It checks against corruption of the xattr_ids count. This can either
lead to the above kmalloc failure, or a smaller than expected
table to be read.
3. It checks the contents of the index table for corruption.
[[email protected]: fix checkpatch issue]
Link: https://lkml.kernel.org/r/[email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Phillip Lougher <[email protected]>
Reported-by: [email protected]
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Sysbot has reported an "slab-out-of-bounds read" error which has been
identified as being caused by a corrupted "ino_num" value read from the
inode. This could be because the metadata block is uncompressed, or
because the "compression" bit has been corrupted (turning a compressed
block into an uncompressed block).
This patch adds additional sanity checks to detect this, and the
following corruption.
1. It checks against corruption of the inodes count. This can either
lead to a larger table to be read, or a smaller than expected
table to be read.
In the case of a too large inodes count, this would often have been
trapped by the existing sanity checks, but this patch introduces
a more exact check, which can identify too small values.
2. It checks the contents of the index table for corruption.
[[email protected]: fix checkpatch issue]
Link: https://lkml.kernel.org/r/[email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Phillip Lougher <[email protected]>
Reported-by: [email protected]
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Sysbot has reported a number of "slab-out-of-bounds reads" and
"use-after-free read" errors which has been identified as being caused
by a corrupted index value read from the inode. This could be because
the metadata block is uncompressed, or because the "compression" bit has
been corrupted (turning a compressed block into an uncompressed block).
This patch adds additional sanity checks to detect this, and the
following corruption.
1. It checks against corruption of the ids count. This can either
lead to a larger table to be read, or a smaller than expected
table to be read.
In the case of a too large ids count, this would often have been
trapped by the existing sanity checks, but this patch introduces
a more exact check, which can identify too small values.
2. It checks the contents of the index table for corruption.
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Phillip Lougher <[email protected]>
Reported-by: [email protected]
Reported-by: [email protected]
Reported-by: [email protected]
Reported-by: [email protected]
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Patch series "Squashfs: fix BIO migration regression and add sanity checks".
Patch [1/4] fixes a regression introduced by the "migrate from
ll_rw_block usage to BIO" patch, which has produced a number of
Sysbot/Syzkaller reports.
Patches [2/4], [3/4], and [4/4] fix a number of filesystem corruption
issues which have produced Sysbot reports in the id, inode and xattr
lookup code.
Each patch has been tested against the Sysbot reproducers using the
given kernel configuration. They have the appropriate "Reported-by:"
lines added.
Additionally, all of the reproducer filesystems are indirectly fixed by
patch [4/4] due to the fact they all have xattr corruption which is now
detected there.
Additional testing with other configurations and architectures (32bit,
big endian), and normal filesystems has also been done to trap any
inadvertent regressions caused by the additional sanity checks.
This patch (of 4):
This is a regression introduced by the patch "migrate from ll_rw_block
usage to BIO".
Sysbot/Syskaller has reported a number of "out of bounds writes" and
"unable to handle kernel paging request in squashfs_decompress" errors
which have been identified as a regression introduced by the above
patch.
Specifically, the patch removed the following sanity check
if (length < 0 || length > output->length ||
(index + length) > msblk->bytes_used)
This check did two things:
1. It ensured any reads were not beyond the end of the filesystem
2. It ensured that the "length" field read from the filesystem
was within the expected maximum length. Without this any
corrupted values can over-run allocated buffers.
Link: https://lkml.kernel.org/r/[email protected]
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 93e72b3c612adc ("squashfs: migrate from ll_rw_block usage to BIO")
Reported-by: [email protected]
Signed-off-by: Phillip Lougher <[email protected]>
Cc: Philippe Liard <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c fix from Alexandre Belloni:
"A single build warning fix"
* tag 'i3c/fixes-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c/master/mipi-i3c-hci: Fix position of __maybe_unused in i3c_hci_of_match
|
|
While reviewing a different fix, John and I noticed an oddity in one of the
BPF program dumps that stood out, for example:
# bpftool p d x i 13
0: (b7) r0 = 808464450
1: (b4) w4 = 808464432
2: (bc) w0 = w0
3: (15) if r0 == 0x0 goto pc+1
4: (9c) w4 %= w0
[...]
In line 2 we noticed that the mov32 would 32 bit truncate the original src
register for the div/mod operation. While for the two operations the dst
register is typically marked unknown e.g. from adjust_scalar_min_max_vals()
the src register is not, and thus verifier keeps tracking original bounds,
simplified:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = -1
1: R0_w=invP-1 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (b7) r1 = -1
2: R0_w=invP-1 R1_w=invP-1 R10=fp0
2: (3c) w0 /= w1
3: R0_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R1_w=invP-1 R10=fp0
3: (77) r1 >>= 32
4: R0_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R1_w=invP4294967295 R10=fp0
4: (bf) r0 = r1
5: R0_w=invP4294967295 R1_w=invP4294967295 R10=fp0
5: (95) exit
processed 6 insns (limit 1000000) max_states_per_insn 0 total_states 0 peak_states 0 mark_read 0
Runtime result of r0 at exit is 0 instead of expected -1. Remove the
verifier mov32 src rewrite in div/mod and replace it with a jmp32 test
instead. After the fix, we result in the following code generation when
having dividend r1 and divisor r6:
div, 64 bit: div, 32 bit:
0: (b7) r6 = 8 0: (b7) r6 = 8
1: (b7) r1 = 8 1: (b7) r1 = 8
2: (55) if r6 != 0x0 goto pc+2 2: (56) if w6 != 0x0 goto pc+2
3: (ac) w1 ^= w1 3: (ac) w1 ^= w1
4: (05) goto pc+1 4: (05) goto pc+1
5: (3f) r1 /= r6 5: (3c) w1 /= w6
6: (b7) r0 = 0 6: (b7) r0 = 0
7: (95) exit 7: (95) exit
mod, 64 bit: mod, 32 bit:
0: (b7) r6 = 8 0: (b7) r6 = 8
1: (b7) r1 = 8 1: (b7) r1 = 8
2: (15) if r6 == 0x0 goto pc+1 2: (16) if w6 == 0x0 goto pc+1
3: (9f) r1 %= r6 3: (9c) w1 %= w6
4: (b7) r0 = 0 4: (b7) r0 = 0
5: (95) exit 5: (95) exit
x86 in particular can throw a 'divide error' exception for div
instruction not only for divisor being zero, but also for the case
when the quotient is too large for the designated register. For the
edx:eax and rdx:rax dividend pair it is not an issue in x86 BPF JIT
since we always zero edx (rdx). Hence really the only protection
needed is against divisor being zero.
Fixes: 68fda450a7df ("bpf: fix 32-bit divide by zero")
Co-developed-by: John Fastabend <[email protected]>
Signed-off-by: John Fastabend <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
|
|
Anatoly has been fuzzing with kBdysch harness and reported a hang in
one of the outcomes:
func#0 @0
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = 808464450
1: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (b4) w4 = 808464432
2: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP808464432 R10=fp0
2: (9c) w4 %= w0
3: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R10=fp0
3: (66) if w4 s> 0x30303030 goto pc+0
R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff),s32_max_value=808464432) R10=fp0
4: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff),s32_max_value=808464432) R10=fp0
4: (7f) r0 >>= r0
5: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff),s32_max_value=808464432) R10=fp0
5: (9c) w4 %= w0
6: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
6: (66) if w0 s> 0x3030 goto pc+0
R0_w=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
7: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
7: (d6) if w0 s<= 0x303030 goto pc+1
9: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
9: (95) exit
propagating r0
from 6 to 7: safe
4: R0_w=invP808464450 R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umin_value=808464433,umax_value=2147483647,var_off=(0x0; 0x7fffffff)) R10=fp0
4: (7f) r0 >>= r0
5: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0,umin_value=808464433,umax_value=2147483647,var_off=(0x0; 0x7fffffff)) R10=fp0
5: (9c) w4 %= w0
6: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
6: (66) if w0 s> 0x3030 goto pc+0
R0_w=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
propagating r0
7: safe
propagating r0
from 6 to 7: safe
processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 1
The underlying program was xlated as follows:
# bpftool p d x i 10
0: (b7) r0 = 808464450
1: (b4) w4 = 808464432
2: (bc) w0 = w0
3: (15) if r0 == 0x0 goto pc+1
4: (9c) w4 %= w0
5: (66) if w4 s> 0x30303030 goto pc+0
6: (7f) r0 >>= r0
7: (bc) w0 = w0
8: (15) if r0 == 0x0 goto pc+1
9: (9c) w4 %= w0
10: (66) if w0 s> 0x3030 goto pc+0
11: (d6) if w0 s<= 0x303030 goto pc+1
12: (05) goto pc-1
13: (95) exit
The verifier rewrote original instructions it recognized as dead code with
'goto pc-1', but reality differs from verifier simulation in that we are
actually able to trigger a hang due to hitting the 'goto pc-1' instructions.
Taking a closer look at the verifier analysis, the reason is that it misjudges
its pruning decision at the first 'from 6 to 7: safe' occasion. What happens
is that while both old/cur registers are marked as precise, they get misjudged
for the jmp32 case as range_within() yields true, meaning that the prior
verification path with a wider register bound could be verified successfully
and therefore the current path with a narrower register bound is deemed safe
as well whereas in reality it's not. R0 old/cur path's bounds compare as
follows:
old: smin_value=0x8000000000000000,smax_value=0x7fffffffffffffff,umin_value=0x0,umax_value=0xffffffffffffffff,var_off=(0x0; 0xffffffffffffffff)
cur: smin_value=0x8000000000000000,smax_value=0x7fffffff7fffffff,umin_value=0x0,umax_value=0xffffffff7fffffff,var_off=(0x0; 0xffffffff7fffffff)
old: s32_min_value=0x80000000,s32_max_value=0x00003030,u32_min_value=0x00000000,u32_max_value=0xffffffff
cur: s32_min_value=0x00003031,s32_max_value=0x7fffffff,u32_min_value=0x00003031,u32_max_value=0x7fffffff
The 64 bit bounds generally look okay and while the information that got
propagated from 32 to 64 bit looks correct as well, it's not precise enough
for judging a conditional jmp32. Given the latter only operates on subregisters
we also need to take these into account as well for a range_within() probe
in order to be able to prune paths. Extending the range_within() constraint
to both bounds will be able to tell us that the old signed 32 bit bounds are
not wider than the cur signed 32 bit bounds.
With the fix in place, the program will now verify the 'goto' branch case as
it should have been:
[...]
6: R0_w=invP(id=0) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
6: (66) if w0 s> 0x3030 goto pc+0
R0_w=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
7: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
7: (d6) if w0 s<= 0x303030 goto pc+1
9: R0=invP(id=0,s32_max_value=12336) R1=ctx(id=0,off=0,imm=0) R4=invP(id=0) R10=fp0
9: (95) exit
7: R0_w=invP(id=0,smax_value=9223372034707292159,umax_value=18446744071562067967,var_off=(0x0; 0xffffffff7fffffff),s32_min_value=12337,u32_min_value=12337,u32_max_value=2147483647) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
7: (d6) if w0 s<= 0x303030 goto pc+1
R0_w=invP(id=0,smax_value=9223372034707292159,umax_value=18446744071562067967,var_off=(0x0; 0xffffffff7fffffff),s32_min_value=3158065,u32_min_value=3158065,u32_max_value=2147483647) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
8: R0_w=invP(id=0,smax_value=9223372034707292159,umax_value=18446744071562067967,var_off=(0x0; 0xffffffff7fffffff),s32_min_value=3158065,u32_min_value=3158065,u32_max_value=2147483647) R1=ctx(id=0,off=0,imm=0) R4_w=invP(id=0) R10=fp0
8: (30) r0 = *(u8 *)skb[808464432]
BPF_LD_[ABS|IND] uses reserved fields
processed 11 insns (limit 1000000) max_states_per_insn 1 total_states 1 peak_states 1 mark_read 1
The bug is quite subtle in the sense that when verifier would determine that
a given branch is dead code, it would (here: wrongly) remove these instructions
from the program and hard-wire the taken branch for privileged programs instead
of the 'goto pc-1' rewrites which will cause hard to debug problems.
Fixes: 3f50f132d840 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Anatoly Trosinenko <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Reviewed-by: John Fastabend <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
|
|
Fix incorrect is_branch{32,64}_taken() analysis for the jsgt case. The return
code for both will tell the caller whether a given conditional jump is taken
or not, e.g. 1 means branch will be taken [for the involved registers] and the
goto target will be executed, 0 means branch will not be taken and instead we
fall-through to the next insn, and last but not least a -1 denotes that it is
not known at verification time whether a branch will be taken or not. Now while
the jsgt has the branch-taken case correct with reg->s32_min_value > sval, the
branch-not-taken case is off-by-one when testing for reg->s32_max_value < sval
since the branch will also be taken for reg->s32_max_value == sval. The jgt
branch analysis, for example, gets this right.
Fixes: 3f50f132d840 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Fixes: 4f7b3e82589e ("bpf: improve verifier branch analysis")
Signed-off-by: Daniel Borkmann <[email protected]>
Reviewed-by: John Fastabend <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) nf_conntrack_tuple_taken() needs to recheck zone for
NAT clash resolution, from Florian Westphal.
2) Restore support for stateful expressions when set definition
specifies no stateful expressions.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
In vsock_shutdown() we touched some socket fields without holding the
socket lock, such as 'state' and 'sk_flags'.
Also, after the introduction of multi-transport, we are accessing
'vsk->transport' in vsock_send_shutdown() without holding the lock
and this call can be made while the connection is in progress, so
the transport can change in the meantime.
To avoid issues, we hold the socket lock when we enter in
vsock_shutdown() and release it when we leave.
Among the transports that implement the 'shutdown' callback, only
hyperv_transport acquired the lock. Since the caller now holds it,
we no longer take it.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Huazhong Tan says:
====================
net: hns3: fixes for -net
The parameters sent from vf may be unreliable. If these
parameters are used directly, memory overwriting may occur.
So this series adds some checks for this case.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this index before using it in hclge_get_rss_key().
Fixes: a638b1d8cc87 ("net: hns3: fix get VF RSS issue")
Signed-off-by: Yufeng Mo <[email protected]>
Signed-off-by: Huazhong Tan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The tqp_index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this tqp_index before using it in hclge_get_ring_chain_from_mbx().
Fixes: 84e095d64ed9 ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox")
Signed-off-by: Yufeng Mo <[email protected]>
Signed-off-by: Huazhong Tan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The queue_id is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this queue_id before using it in hclge_reset_vf_queue().
Fixes: 1a426f8b40fc ("net: hns3: fix the VF queue reset flow error")
Signed-off-by: Yufeng Mo <[email protected]>
Signed-off-by: Huazhong Tan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b13f ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The TypeC FIA can be powered down if the TC-COLD power state is allowed,
so block the TC-COLD state when initializing the FIA.
Note that this isn't needed on ICL where the FIA is never modular and
which has no generic way to block TC-COLD (except for platforms with a
legacy TypeC port and on those too only via these legacy ports, not via
a DP-alt/TBT port).
Cc: <[email protected]> # v5.10+
Cc: José Roberto de Souza <[email protected]>
Reported-by: Paul Menzel <[email protected]>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3027
Signed-off-by: Imre Deak <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Jos� Roberto de Souza <[email protected]>
(cherry picked from commit f48993e5d26b079e8c80fff002499a213dbdb1b4)
Signed-off-by: Jani Nikula <[email protected]>
|
|
This fixes a regression following dfs links that was introduced in the
patch series for the new mount api.
Signed-off-by: Ronnie Sahlberg <[email protected]>
Reviewed-by: Paulo Alcantara (SUSE) <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
Commit
20bf2b378729 ("x86/build: Disable CET instrumentation in the kernel")
disabled CET instrumentation which gets added by default by the Ubuntu
gcc9 and 10 by default, but did that only for 64-bit builds. It would
still fail when building a 32-bit target. So disable CET for all x86
builds.
Fixes: 20bf2b378729 ("x86/build: Disable CET instrumentation in the kernel")
Reported-by: AC <[email protected]>
Signed-off-by: Borislav Petkov <[email protected]>
Acked-by: Josh Poimboeuf <[email protected]>
Tested-by: AC <[email protected]>
Link: https://lkml.kernel.org/r/YCCIgMHkzh/[email protected]
|
|
The sdebug_q_arr pointer must be freed when the module is unloaded.
$ cat /sys/kernel/debug/kmemleak
unreferenced object 0xffff888e1cfb0000 (size 4096):
comm "modprobe", pid 165555, jiffies 4325987516 (age 685.194s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000458f4f5d>] 0xffffffffc06702d9
[<000000003edc4b1f>] do_one_initcall+0xe9/0x57d
[<00000000da7d518c>] do_init_module+0x1d1/0x6f0
[<000000009a6a9248>] load_module+0x36bd/0x4f50
[<00000000ddb0c3ce>] __do_sys_init_module+0x1db/0x260
[<000000009532db57>] do_syscall_64+0xa5/0x420
[<000000002916b13d>] entry_SYSCALL_64_after_hwframe+0x6a/0xdf
Fixes: 87c715dcde63 ("scsi: scsi_debug: Add per_host_store option")
Link: https://lore.kernel.org/r/[email protected]
Acked-by: Douglas Gilbert <[email protected]>
Signed-off-by: Maurizio Lombardi <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Horatiu Vultur says:
====================
bridge: mrp: Fix br_mrp_port_switchdev_set_state
Based on the discussion here[1], there was a problem with the function
br_mrp_port_switchdev_set_state. The problem was that it was called
both with BR_STATE* and BR_MRP_PORT_STATE* types. This patch series
fixes this issue and removes SWITCHDEV_ATTR_ID_MRP_PORT_STAT because
is not used anymore.
[1] https://www.spinics.net/lists/netdev/msg714816.html
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Now that MRP started to use also SWITCHDEV_ATTR_ID_PORT_STP_STATE to
notify HW, then SWITCHDEV_ATTR_ID_MRP_PORT_STAT is not used anywhere
else, therefore we can remove it.
Fixes: c284b545900830 ("switchdev: mrp: Extend switchdev API to offload MRP")
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The function br_mrp_port_switchdev_set_state was called both with MRP
port state and STP port state, which is an issue because they don't
match exactly.
Therefore, update the function to be used only with STP port state and
use the id SWITCHDEV_ATTR_ID_PORT_STP_STATE.
The choice of using STP over MRP is that the drivers already implement
SWITCHDEV_ATTR_ID_PORT_STP_STATE and already in SW we update the port
STP state.
Fixes: 9a9f26e8f7ea30 ("bridge: mrp: Connect MRP API with the switchdev API")
Fixes: fadd409136f0f2 ("bridge: switchdev: mrp: Implement MRP API for switchdev")
Fixes: 2f1a11ae11d222 ("bridge: mrp: Add MRP interface.")
Reported-by: Rasmus Villemoes <[email protected]>
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Prevent netif_tx_disable() running concurrently with dev_watchdog() by
taking the device global xmit lock. Otherwise, the recommended:
netif_carrier_off(dev);
netif_tx_disable(dev);
driver shutdown sequence can happen after the watchdog has already
checked carrier, resulting in possible false alarms. This is because
netif_tx_lock() only sets the frozen bit without maintaining the locks
on the individual queues.
Fixes: c3f26a269c24 ("netdev: Fix lockdep warnings in multiqueue configurations.")
Signed-off-by: Edwin Peer <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Restore the original behaviour where users are allowed to add an element
with any stateful expression if the set definition specifies no stateful
expressions. Make sure upper maximum number of stateful expressions of
NFT_SET_EXPR_MAX is not reached.
Fixes: 8cfd9b0f8515 ("netfilter: nftables: generalize set expressions support")
Fixes: 48b0ae046ee9 ("netfilter: nftables: netlink support for several set element expressions")
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
The origin skip check needs to re-test the zone. Else, we might skip
a colliding tuple in the reply direction.
This only occurs when using 'directional zones' where origin tuples
reside in different zones but the reply tuples share the same zone.
This causes the new conntrack entry to be dropped at confirmation time
because NAT clash resolution was elided.
Fixes: 4e35c1cb9460240 ("netfilter: nf_nat: skip nat clash resolution for same-origin entries")
Signed-off-by: Florian Westphal <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
If the socket is closed or is being released, some resources used by
virtio_transport_space_update() such as 'vsk->trans' may be released.
To avoid a use after free bug we should only update the available credit
when we are sure the socket is still open and we have the lock held.
Fixes: 06a8fc78367d ("VSOCK: Introduce virtio_vsock_common.ko")
Signed-off-by: Stefano Garzarella <[email protected]>
Acked-by: Michael S. Tsirkin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix output of top level event tracing 'enable' file.
When writing a tool for enabling events in the tracing system, an
anomaly was discovered. The top level event 'enable' file would never
show '1' when all events were enabled.
The system and event 'enable' files worked as expected.
The reason was because the top level event 'enable' file included the
'ftrace' tracer events, which are not controlled by the 'enable' file
and would cause the output to be wrong. This appears to have been a
bug since it was created"
* tag 'trace-v5.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do not count ftrace events in top level enable output
|
|
The sctp transport seq_file iterators take a reference to the transport
in the ->start and ->next functions and releases the reference in the
->show function. The preferred handling for such resources is to
release them in the subsequent ->next or ->stop function call.
Since Commit 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration
code and interface") there is no guarantee that ->show will be called
after ->next, so this function can now leak references.
So move the sctp_transport_put() call to ->next and ->stop.
Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code and interface")
Reported-by: Xin Long <[email protected]>
Signed-off-by: NeilBrown <[email protected]>
Acked-by: Marcelo Ricardo Leitner <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This has been shown in tests:
[ +0.000008] WARNING: CPU: 3 PID: 7620 at kernel/rcu/srcutree.c:374 cleanup_srcu_struct+0xed/0x100
This is essentially a use-after free, although SRCU notices it as
an SRCU cleanup in an invalid context.
== Background ==
SGX has a data structure (struct sgx_encl_mm) which keeps per-mm SGX
metadata. This is separate from struct sgx_encl because, in theory,
an enclave can be mapped from more than one mm. sgx_encl_mm includes
a pointer back to the sgx_encl.
This means that sgx_encl must have a longer lifetime than all of the
sgx_encl_mm's that point to it. That's usually the case: sgx_encl_mm
is freed only after the mmu_notifier is unregistered in sgx_release().
However, there's a race. If the process is exiting,
sgx_mmu_notifier_release() can be called in parallel with sgx_release()
instead of being called *by* it. The mmu_notifier path keeps encl_mm
alive past when sgx_encl can be freed. This inverts the lifetime rules
and means that sgx_mmu_notifier_release() can access a freed sgx_encl.
== Fix ==
Increase encl->refcount when encl_mm->encl is established. Release
this reference when encl_mm is freed. This ensures that encl outlives
encl_mm.
[ bp: Massage commit message. ]
Fixes: 1728ab54b4be ("x86/sgx: Add a page reclaimer")
Reported-by: Haitao Huang <[email protected]>
Signed-off-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Borislav Petkov <[email protected]>
Acked-by: Dave Hansen <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
This reverts commit 32cf1a12cad43358e47dac8014379c2f33dfbed4.
The 'exisitng buffer' in this case is the firmware provided table, and
we should not modify that in place. This fixes a crash on arm64 with
initrd table overrides, in which case the DSDT is not mapped with
read/write permissions.
Reported-by: Shawn Guo <[email protected]>
Signed-off-by: Ard Biesheuvel <[email protected]>
Tested-by: Shawn Guo <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
If the maximum performance level taken for computing the
arch_max_freq_ratio value used in the x86 scale-invariance code is
higher than the one corresponding to the cpuinfo.max_freq value
coming from the acpi_cpufreq driver, the scale-invariant utilization
falls below 100% even if the CPU runs at cpuinfo.max_freq or slightly
faster, which causes the schedutil governor to select a frequency
below cpuinfo.max_freq. That frequency corresponds to a frequency
table entry below the maximum performance level necessary to get to
the "boost" range of CPU frequencies which prevents "boost"
frequencies from being used in some workloads.
While this issue is related to scale-invariance, it may be amplified
by commit db865272d9c4 ("cpufreq: Avoid configuring old governors as
default with intel_pstate") from the 5.10 development cycle which
made it extremely easy to default to schedutil even if the preferred
driver is acpi_cpufreq as long as intel_pstate is built too, because
the mere presence of the latter effectively removes the ondemand
governor from the defaults. Distro kernels are likely to include
both intel_pstate and acpi_cpufreq on x86, so their users who cannot
use intel_pstate or choose to use acpi_cpufreq may easily be
affectecd by this issue.
If CPPC is available, it can be used to address this issue by
extending the frequency tables created by acpi_cpufreq to cover the
entire available frequency range (including "boost" frequencies) for
each CPU, but if CPPC is not there, acpi_cpufreq has no idea what
the maximum "boost" frequency is and the frequency tables created by
it cannot be extended in a meaningful way, so in that case make it
ask the arch scale-invariance code to to use the "nominal" performance
level for CPU utilization scaling in order to avoid the issue at hand.
Fixes: db865272d9c4 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Signed-off-by: Rafael J. Wysocki <[email protected]>
Reviewed-by: Giovanni Gherdovich <[email protected]>
Acked-by: Peter Zijlstra (Intel) <[email protected]>
|
|
A severe performance regression on AMD EPYC processors when using
the schedutil scaling governor was discovered by Phoronix.com and
attributed to the following commits:
41ea667227ba ("x86, sched: Calculate frequency invariance for AMD
systems")
976df7e5730e ("x86, sched: Use midpoint of max_boost and max_P for
frequency invariance on AMD EPYC")
The source of the problem is that the maximum performance level taken
for computing the arch_max_freq_ratio value used in the x86 scale-
invariance code is higher than the one corresponding to the
cpuinfo.max_freq value coming from the acpi_cpufreq driver.
This effectively causes the scale-invariant utilization to fall below
100% even if the CPU runs at cpuinfo.max_freq or slightly faster, so
the schedutil governor selects a frequency below cpuinfo.max_freq
then. That frequency corresponds to a frequency table entry below
the maximum performance level necessary to get to the "boost" range
of CPU frequencies.
However, if the cpuinfo.max_freq value coming from acpi_cpufreq was
higher, the schedutil governor would select higher frequencies which
in turn would allow acpi_cpufreq to set more adequate performance
levels and to get to the "boost" range of CPU frequencies more often.
This issue affects any systems where acpi_cpufreq is used and the
"boost" (or "turbo") frequencies are enabled, not just AMD EPYC.
Moreover, commit db865272d9c4 ("cpufreq: Avoid configuring old
governors as default with intel_pstate") from the 5.10 development
cycle made it extremely easy to default to schedutil even if the
preferred driver is acpi_cpufreq as long as intel_pstate is built
too, because the mere presence of the latter effectively removes the
ondemand governor from the defaults. Distro kernels are likely to
include both intel_pstate and acpi_cpufreq on x86, so their users
who cannot use intel_pstate or choose to use acpi_cpufreq may
easily be affectecd by this issue.
To address this issue, extend the frequency table constructed by
acpi_cpufreq for each CPU to cover the entire range of available
frequencies (including the "boost" ones) if CPPC is available and
indicates that "boost" (or "turbo") frequencies are enabled. That
causes cpuinfo.max_freq to become the maximum "boost" frequency of
the given CPU (instead of the maximum frequency returned by the ACPI
_PSS object that corresponds to the "nominal" performance level).
Fixes: 41ea667227ba ("x86, sched: Calculate frequency invariance for AMD systems")
Fixes: 976df7e5730e ("x86, sched: Use midpoint of max_boost and max_P for frequency invariance on AMD EPYC")
Fixes: db865272d9c4 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Link: https://www.phoronix.com/scan.php?page=article&item=linux511-amd-schedutil&num=1
Link: https://lore.kernel.org/linux-pm/[email protected]/
Reported-by: Michael Larabel <[email protected]>
Diagnosed-by: Giovanni Gherdovich <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
Tested-by: Giovanni Gherdovich <[email protected]>
Reviewed-by: Giovanni Gherdovich <[email protected]>
Tested-by: Michael Larabel <[email protected]>
|
|
This reverts commit 842067940a3e3fc008a60fee388e000219b32632.
For some solutions e.g. sound/soc/intel/catpt, DW DMA is part of a
compound device (in that very example, domains: ADSP, SSP0, SSP1, DMA0
and DMA1 are part of a single entity) rather than being a standalone
one. Driver for said device may enlist DMA to transfer data during
suspend or resume sequences.
Manipulating RPM explicitly in dw's DMA request and release channel
functions causes suspend() to also invoke resume() for the exact same
device. Similar situation occurs for resume() sequence. Effectively
renders device dysfunctional after first suspend() attempt. Revert the
change to address the problem.
Fixes: 842067940a3e ("dmaengine: dw: Enable runtime PM")
Cc: Andy Shevchenko <[email protected]>
Signed-off-by: Cezary Rojewski <[email protected]>
Acked-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A fix for a crash scenario that has been present since the initial
merge, a minor regression in sysfs attribute visibility, and a fix for
some flexible array warnings.
The bulk of this pull is an update to the libnvdimm unit test
infrastructure to test non-ACPI platforms. Given there is zero
regression risk for test updates, and the tests enable validation of
bits headed towards the next merge window, I saw no reason to hold the
new tests back. Santosh originally submitted this before the v5.11
window opened.
Summary:
- Fix a crash when sysfs accesses race 'dimm' driver probe/remove.
- Fix a regression in 'resource' attribute visibility necessary for
mapping badblocks and other physical address interrogations.
- Fix some flexible array warnings
- Expand the unit test infrastructure for non-ACPI platforms"
* tag 'libnvdimm-fixes-5.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/dimm: Avoid race between probe and available_slots_show()
ndtest: Add papr health related flags
ndtest: Add nvdimm control functions
ndtest: Add regions and mappings to the test buses
ndtest: Add dimm attributes
ndtest: Add dimms to the two buses
ndtest: Add compatability string to treat it as PAPR family
testing/nvdimm: Add test module for non-nfit platforms
libnvdimm/namespace: Fix visibility of namespace resource attribute
libnvdimm/pmem: Remove unused header
ACPI: NFIT: Fix flexible_array.cocci warnings
|