| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- move freeing of GPIO hogs to after freeing the device to get rid of a
warning state.
- a small compile warning fix
* tag 'gpio-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Move freeing of GPIO hogs before numbing of the device
gpio: mxs: remove __init annotation
|
|
While in RUNNING state, phy_state_machine() checks for link changes by
comparing phydev->link before and after calling phy_read_status().
This works as long as it is guaranteed that phydev->link is never
changed outside the phy_state_machine().
If in some setups this happens, it causes the state machine to miss
a link loss and remain RUNNING despite phydev->link being 0.
This has been observed running a dsa setup with a process continuously
polling the link states over ethtool each second (SNMPD RFC-1213
agent). Disconnecting the link on a phy followed by a ETHTOOL_GSET
causes dsa_slave_get_settings() / dsa_slave_get_link_ksettings() to
call phy_read_status() and with that modify the link status - and
with that bricking the phy state machine.
This patch adds a fail-safe check while in RUNNING, which causes to
move to CHANGELINK when the link is gone and we are still RUNNING.
Signed-off-by: Zefir Kurtisi <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Pull networking fixes from David Miller:
1) Fix dumping of nft_quota entries, from Pablo Neira Ayuso.
2) Fix out of bounds access in nf_tables discovered by KASAN, from
Florian Westphal.
3) Fix IRQ enabling in dp83867 driver, from Grygorii Strashko.
4) Fix unicast filtering in be2net driver, from Ivan Vecera.
5) tg3_get_stats64() can race with driver close and ethtool
reconfigurations, fix from Michael Chan.
6) Fix error handling when pass limit is reached in bpf code gen on
x86. From Daniel Borkmann.
7) Don't clobber switch ops and use proper MDIO nested reads and writes
in bcm_sf2 driver, from Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
net: dsa: bcm_sf2: Utilize nested MDIO read/write
net: dsa: bcm_sf2: Do not clobber b53_switch_ops
net: stmmac: fix maxmtu assignment to be within valid range
bpf: change back to orig prog on too many passes
tg3: Fix race condition in tg3_get_stats64().
be2net: fix unicast list filling
be2net: fix accesses to unicast list
netlabel: add CALIPSO to the list of built-in protocols
vti6: fix device register to report IFLA_INFO_KIND
net: phy: dp83867: fix irq generation
amd-xgbe: Fix IRQ processing when running in single IRQ mode
sh_eth: R8A7740 supports packet shecksumming
sh_eth: fix EESIPR values for SH77{34|63}
r8169: fix the typo in the comment
nl80211: fix sched scan netlink socket owner destruction
bridge: netfilter: Fix dropping packets that moving through bridge interface
netfilter: ipt_CLUSTERIP: check duplicate config when initializing
netfilter: nft_payload: mangle ckecksum if NFT_PAYLOAD_L4CSUM_PSEUDOHDR is set
netfilter: nf_tables: fix oob access
netfilter: nft_queue: use raw_smp_processor_id()
...
|
|
Revert to using direct register writes to set the divisor and
line-control registers.
A recent change switched to using the init vendor command to update
these registers, something which also enabled support for CH341A
devices. It turns out that simply setting bit 7 in the divisor register
is sufficient to support CH341A and specifically prevent data from being
buffered until a full endpoint-size packet (32 bytes) has been received.
Using the init command also had the side-effect of temporarily
deasserting the DTR/RTS signals on every termios change (including
initialisation on open) something which for example could cause problems
in setups where DTR is used to trigger a reset.
Fixes: 4e46c410e050 ("USB: serial: ch341: reinitialize chip on
reconfiguration")
Signed-off-by: Johan Hovold <[email protected]>
|
|
A recent change added support for modifying the default line-control
settings, but did not make sure that the modified settings were used as
part of reconfiguration after a device has been reset during resume.
This caused a port that was open before suspend to be unusable until
being closed and reopened.
Fixes: ba781bdf8662 ("USB: serial: ch341: add support for parity, frame
length, stop bits")
Signed-off-by: Johan Hovold <[email protected]>
|
|
Fix reset-resume handling which failed to resubmit the read and
interrupt URBs, thereby leaving a port that was open before suspend in a
broken state until closed and reopened.
Fixes: 1ded7ea47b88 ("USB: ch341 serial: fix port number changed after
resume")
Fixes: 2bfd1c96a9fb ("USB: serial: ch341: remove reset_resume callback")
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to stop the interrupt URB before returning on errors during
open.
Fixes: 664d5df92e88 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The modem-control signals are managed by the tty-layer during open and
should not be asserted prematurely when set_termios is called from
driver open.
Also make sure that the signals are asserted only when changing speed
from B0.
Fixes: 664d5df92e88 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The private baud_rate variable is used to configure the port at open and
reset-resume and must never be set to (and left at) zero or reset-resume
and all further open attempts will fail.
Fixes: aa91def41a7b ("USB: ch341: set tty baud speed according to tty
struct")
Fixes: 664d5df92e88 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
DTR and RTS will be asserted by the tty-layer when the port is opened
and deasserted on close (if HUPCL is set). Make sure the initial state
is not-asserted before the port is first opened as well.
Fixes: 664d5df92e88 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The i2s clock pre-divider 1 is used for both i2s1 and sysclk.
The i2s1 is usually used for the main i2s and the pre-divider
will be set in hw_params function.
However, if i2s2 is used, the pre-divider is not set in the hw_params
function and the default value of i2s clock pre-divider 1 is too high
for sysclk and DMIC usage. Fix by overriding default divider value to 2.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=95681
Tested-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
Add the missing declarations of basic string functions to string.h to allow
a clean build.
Fixes: 5be865661516 ("String-handling functions for the new x86 setup code.")
Signed-off-by: Nicholas Mc Guire <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
We've recently added the fsid to trace events, this makes the line quite
long. To reduce the it again, remove extra spaces around = and remove
",".
Signed-off-by: David Sterba <[email protected]>
|
|
This can help us monitor truncated ordered extents.
Signed-off-by: Liu Bo <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
'inode' is an important field for btrfs_get_extent, lets trace it.
Signed-off-by: Liu Bo <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
Enabling btrfs tracepoints leads to instant crash, as reported. The wq
callbacks could free the memory and the tracepoints started to
dereference the members to get to fs_info.
The proposed fix https://marc.info/?l=linux-btrfs&m=148172436722606&w=2
removed the tracepoints but we could preserve them by passing only the
required data in a safe way.
Fixes: bc074524e123 ("btrfs: prefix fsid to all trace events")
CC: [email protected] # 4.8+
Reported-by: Sebastian Andrzej Siewior <[email protected]>
Reviewed-by: Qu Wenruo <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
|
|
Florian Fainelli says:
====================
net: dsa: bcm_sf2: Couple fixes
Here are a couple of fixes for bcm_sf2, please queue these up for -stable
as well, thank you very much!
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
We are implementing a MDIO bus which is behind another one, so use the
nested version of the accessors to get lockdep annotations correct.
Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.
Fixes: f458995b9ad8 ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
into drm-fixes
Fixes for 4.10:
- Polaris 12 support
- Add new amd-gfx mailing list to MAINTAINERS file
- UVD clockgating fix
- SI dpm fixes
* 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: drop verde dpm quirks
drm/radeon: drop verde dpm quirks
drm/radeon: update smc firmware selection for SI
drm/amdgpu: update si kicker smc firmware
drm/amd/powerplay: extend smu's response timeout time.
drm/amdgpu: remove static integer for uvd pp state
drm/amd/amdgpu: add Polaris12 PCI ID
drm/amdgpu/powerplay: add Polaris12 support
drm/amd/amdgpu: add Polaris12 support (v3)
MAINTAINERS: Update mailing list for radeon and amdgpu
|
|
There is no checking valid value of maxmtu when getting it from
device tree. This resolution added the checking condition to
ensure the assignment is made within a valid range.
Signed-off-by: Kweh, Hock Leong <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://people.freedesktop.org/~robclark/linux into drm-fixes
A few fixes for 4.10.. the first fixes a long-standing logic bug, that
by luck (ie. size of packets written into RB for a submit) wasn't hit
on a3xx/a4xx but was causing intermittent GPU lockups on a5xx. And a
couple other robustness issues that Jordan noticed.
* 'msm-fixes-4.10' of git://people.freedesktop.org/~robclark/linux:
drm/msm: Verify that MSM_SUBMIT_BO_FLAGS are set
drm/msm: Put back the vaddr in submit_reloc()
drm/msm: Ensure that the hardware write pointer is valid
|
|
git://people.freedesktop.org/~narmstrong/linux into drm-fixes
- plan atomic check oops fix
- fix CVBS init when HDMI is configured by bootloader
- fix CVBS VDAC disable
* tag 'meson-drm-fixes-for-4.10' of git://people.freedesktop.org/~narmstrong/linux:
drm/meson: Fix CVBS VDAC disable
drm/meson: Fix CVBS initialization when HDMI is configured by bootloader
drm/meson: Fix plane atomic check when no crtc for the plane
|
|
tilcdc fixes for v4.10.
* tag 'tilcdc-4.10-fixes' of https://github.com/jsarha/linux:
drm: tilcdc: simplify the recovery from sync lost error on rev1
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-fixes
single drm fix.
* tag 'drm-misc-fixes-2017-01-04' of git://anongit.freedesktop.org/git/drm-misc:
drm: Clean up planes in atomic commit helper failure path
|
|
|
|
If after too many passes still no image could be emitted, then
swap back to the original program as we do in all other cases
and don't use the one with blinding.
Fixes: 959a75791603 ("bpf, x86: add support for constant blinding")
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 4.10-rc3. Yeah, it's a lot, an
artifact of the holiday break I think.
Lots of gadget and the usual XHCI fixups for reported issues (one day
that driver will calm down...) Also included are a bunch of usb-serial
driver fixes, and for good measure, a number of much-reported MUSB
driver issues have finally been resolved.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (72 commits)
USB: fix problems with duplicate endpoint addresses
usb: ohci-at91: use descriptor-based gpio APIs correctly
usb: storage: unusual_uas: Add JMicron JMS56x to unusual device
usb: hub: Move hub_port_disable() to fix warning if PM is disabled
usb: musb: blackfin: add bfin_fifo_offset in bfin_ops
usb: musb: fix compilation warning on unused function
usb: musb: Fix trying to free already-free IRQ 4
usb: musb: dsps: implement clear_ep_rxintr() callback
usb: musb: core: add clear_ep_rxintr() to musb_platform_ops
USB: serial: ti_usb_3410_5052: fix NULL-deref at open
USB: serial: spcp8x5: fix NULL-deref at open
USB: serial: quatech2: fix sleep-while-atomic in close
USB: serial: pl2303: fix NULL-deref at open
USB: serial: oti6858: fix NULL-deref at open
USB: serial: omninet: fix NULL-derefs at open and disconnect
USB: serial: mos7840: fix misleading interrupt-URB comment
USB: serial: mos7840: remove unused write URB
USB: serial: mos7840: fix NULL-deref at open
USB: serial: mos7720: remove obsolete port initialisation
USB: serial: mos7720: fix parallel probe
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are a few small char/misc driver fixes for 4.10-rc3.
Two MEI driver fixes, and three NVMEM patches for reported issues, and
a new Hyper-V driver MAINTAINER update. Nothing major at all, all have
been in linux-next with no reported issues"
* tag 'char-misc-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
hyper-v: Add myself as additional MAINTAINER
nvmem: fix nvmem_cell_read() return type doc
nvmem: imx-ocotp: Fix wrong register size
nvmem: qfprom: Allow single byte accesses for read/write
mei: move write cb to completion on credentials failures
mei: bus: fix mei_cldev_enable KDoc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are some staging and IIO driver fixes for 4.10-rc3.
Most of these are minor IIO fixes of reported issues, along with one
network driver fix to resolve an issue. And a MAINTAINERS update with
a new mailing list. All of these, except the MAINTAINERS file update,
have been in linux-next with no reported issues (the MAINTAINERS patch
happened on Friday...)"
* tag 'staging-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
MAINTAINERS: add greybus subsystem mailing list
staging: octeon: Call SET_NETDEV_DEV()
iio: accel: st_accel: fix LIS3LV02 reading and scaling
iio: common: st_sensors: fix channel data parsing
iio: max44000: correct value in illuminance_integration_time_available
iio: adc: TI_AM335X_ADC should depend on HAS_DMA
iio: bmi160: Fix time needed to sleep after command execution
iio: 104-quad-8: Fix active level mismatch for the preset enable option
iio: 104-quad-8: Fix off-by-one errors when addressing IOR
iio: 104-quad-8: Fix index control configuration
|
|
The driver's ndo_get_stats64() method is not always called under RTNL.
So it can race with driver close or ethtool reconfigurations. Fix the
race condition by taking tp->lock spinlock in tg3_free_consistent()
when freeing the tp->hw_stats memory block. tg3_get_stats64() is
already taking tp->lock.
Reported-by: Wang Yufen <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The adapter->pmac_id[0] item is used for primary MAC address but
this is not true for adapter->uc_list[0] as is assumed in
be_set_uc_list(). There are N UC addresses copied first from net_device
to adapter->uc_list[1..N] and then N UC addresses from
adapter->uc_list[0..N-1] are sent to HW. So the last UC address is never
stored into HW and address 00:00:00:00;00:00 (from uc_list[0]) is used
instead.
Cc: Sathya Perla <[email protected]>
Cc: Ajit Khaparde <[email protected]>
Cc: Sriharsha Basavapatna <[email protected]>
Cc: Somnath Kotur <[email protected]>
Fixes: b717241 be2net: replace polling with sleeping in the FW completion path
Signed-off-by: Ivan Vecera <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Several people report seeing warnings about inconsistent radix tree
nodes followed by crashes in the workingset code, which all looked like
use-after-free access from the shadow node shrinker.
Dave Jones managed to reproduce the issue with a debug patch applied,
which confirmed that the radix tree shrinking indeed frees shadow nodes
while they are still linked to the shadow LRU:
WARNING: CPU: 2 PID: 53 at lib/radix-tree.c:643 delete_node+0x1e4/0x200
CPU: 2 PID: 53 Comm: kswapd0 Not tainted 4.10.0-rc2-think+ #3
Call Trace:
delete_node+0x1e4/0x200
__radix_tree_delete_node+0xd/0x10
shadow_lru_isolate+0xe6/0x220
__list_lru_walk_one.isra.4+0x9b/0x190
list_lru_walk_one+0x23/0x30
scan_shadow_nodes+0x2e/0x40
shrink_slab.part.44+0x23d/0x5d0
shrink_node+0x22c/0x330
kswapd+0x392/0x8f0
This is the WARN_ON_ONCE(!list_empty(&node->private_list)) placed in the
inlined radix_tree_shrink().
The problem is with 14b468791fa9 ("mm: workingset: move shadow entry
tracking to radix tree exceptional tracking"), which passes an update
callback into the radix tree to link and unlink shadow leaf nodes when
tree entries change, but forgot to pass the callback when reclaiming a
shadow node.
While the reclaimed shadow node itself is unlinked by the shrinker, its
deletion from the tree can cause the left-most leaf node in the tree to
be shrunk. If that happens to be a shadow node as well, we don't unlink
it from the LRU as we should.
Consider this tree, where the s are shadow entries:
root->rnode
|
[0 n]
| |
[s ] [sssss]
Now the shadow node shrinker reclaims the rightmost leaf node through
the shadow node LRU:
root->rnode
|
[0 ]
|
[s ]
Because the parent of the deleted node is the first level below the
root and has only one child in the left-most slot, the intermediate
level is shrunk and the node containing the single shadow is put in
its place:
root->rnode
|
[s ]
The shrinker again sees a single left-most slot in a first level node
and thus decides to store the shadow in root->rnode directly and free
the node - which is a leaf node on the shadow node LRU.
root->rnode
|
s
Without the update callback, the freed node remains on the shadow LRU,
where it causes later shrinker runs to crash.
Pass the node updater callback into __radix_tree_delete_node() in case
the deletion causes the left-most branch in the tree to collapse too.
Also add warnings when linked nodes are freed right away, rather than
wait for the use-after-free when the list is scanned much later.
Fixes: 14b468791fa9 ("mm: workingset: move shadow entry tracking to radix tree exceptional tracking")
Reported-by: Dave Chinner <[email protected]>
Reported-by: Hugh Dickins <[email protected]>
Reported-by: Andrea Arcangeli <[email protected]>
Reported-and-tested-by: Dave Jones <[email protected]>
Signed-off-by: Johannes Weiner <[email protected]>
Cc: Christoph Hellwig <[email protected]>
Cc: Chris Leech <[email protected]>
Cc: Lee Duncan <[email protected]>
Cc: Jan Kara <[email protected]>
Cc: Kirill A. Shutemov <[email protected]>
Cc: Matthew Wilcox <[email protected]>
Cc: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
4.10-rc loadtest (even on x86, and even without THPCache) fails with
"fork: Cannot allocate memory" or some such; and /proc/meminfo shows
PageTables growing.
Commit 953c66c2b22a ("mm: THP page cache support for ppc64") that got
merged in rc1 removed the freeing of an unused preallocated pagetable
after do_fault_around() has called map_pages().
This is usually a good optimization, so that the followup doesn't have
to reallocate one; but it's not sufficient to shift the freeing into
alloc_set_pte(), since there are failure cases (most commonly
VM_FAULT_RETRY) which never reach finish_fault().
Check and free it at the outer level in do_fault(), then we don't need
to worry in alloc_set_pte(), and can restore that to how it was (I
cannot find any reason to pte_free() under lock as it was doing).
And fix a separate pagetable leak, or crash, introduced by the same
change, that could only show up on some ppc64: why does do_set_pmd()'s
failure case attempt to withdraw a pagetable when it never deposited
one, at the same time overwriting (so leaking) the vmf->prealloc_pte?
Residue of an earlier implementation, perhaps? Delete it.
Fixes: 953c66c2b22a ("mm: THP page cache support for ppc64")
Cc: Aneesh Kumar K.V <[email protected]>
Cc: Kirill A. Shutemov <[email protected]>
Cc: Michael Ellerman <[email protected]>
Cc: Benjamin Herrenschmidt <[email protected]>
Cc: Michael Neuling <[email protected]>
Cc: Paul Mackerras <[email protected]>
Cc: Balbir Singh <[email protected]>
Cc: Andrew Morton <[email protected]>
Signed-off-by: Hugh Dickins <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fix from Michal Marek:
"The asm-prototypes.h file added in the last merge window results in
invalid code with CONFIG_KMEMCHECK=y. The net result is that genksyms
segfaults.
This pull request fixes the header, the genksyms fix is in my kbuild
branch for 4.11"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
asm-prototypes: Clear any CPP defines before declaring the functions
|
|
The Greybus driver subsystem has a mailing list, so list it in the
MAINTAINERS file so that people know to send patches there as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Acked-by: Johan Hovold <[email protected]>
Reviewed-by: Viresh Kumar <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
With the following commit:
4bc9f92e64c8 ("x86/efi-bgrt: Use efi_mem_reserve() to avoid copying image data")
... efi_bgrt_init() calls into the memblock allocator through
efi_mem_reserve() => efi_arch_mem_reserve() *after* mm_init() has been called.
Indeed, KASAN reports a bad read access later on in efi_free_boot_services():
BUG: KASAN: use-after-free in efi_free_boot_services+0xae/0x24c
at addr ffff88022de12740
Read of size 4 by task swapper/0/0
page:ffffea0008b78480 count:0 mapcount:-127
mapping: (null) index:0x1 flags: 0x5fff8000000000()
[...]
Call Trace:
dump_stack+0x68/0x9f
kasan_report_error+0x4c8/0x500
kasan_report+0x58/0x60
__asan_load4+0x61/0x80
efi_free_boot_services+0xae/0x24c
start_kernel+0x527/0x562
x86_64_start_reservations+0x24/0x26
x86_64_start_kernel+0x157/0x17a
start_cpu+0x5/0x14
The instruction at the given address is the first read from the memmap's
memory, i.e. the read of md->type in efi_free_boot_services().
Note that the writes earlier in efi_arch_mem_reserve() don't splat because
they're done through early_memremap()ed addresses.
So, after memblock is gone, allocations should be done through the "normal"
page allocator. Introduce a helper, efi_memmap_alloc() for this. Use
it from efi_arch_mem_reserve(), efi_free_boot_services() and, for the sake
of consistency, from efi_fake_memmap() as well.
Note that for the latter, the memmap allocations cease to be page aligned.
This isn't needed though.
Tested-by: Dan Williams <[email protected]>
Signed-off-by: Nicolai Stange <[email protected]>
Reviewed-by: Ard Biesheuvel <[email protected]>
Cc: <[email protected]> # v4.9
Cc: Dave Young <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Matt Fleming <[email protected]>
Cc: Mika Penttilä <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Fixes: 4bc9f92e64c8 ("x86/efi-bgrt: Use efi_mem_reserve() to avoid copying image data")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Commit 988d44b "be2net: Avoid redundant addition of mac address in HW"
introduced be_dev_mac_add & be_uc_mac_add helpers that incorrectly
access adapter->uc_list as an array of bytes instead of an array of
be_eth_addr. Consequently NIC is not filled with valid data so unicast
filtering is broken.
Cc: Sathya Perla <[email protected]>
Cc: Ajit Khaparde <[email protected]>
Cc: Sriharsha Basavapatna <[email protected]>
Cc: Somnath Kotur <[email protected]>
Fixes: 988d44b be2net: Avoid redundant addition of mac address in HW
Signed-off-by: Ivan Vecera <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When we added CALIPSO support in Linux v4.8 we forgot to add it to the
list of supported protocols with display at boot.
Signed-off-by: Paul Moore <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing particular stands out, only a few small fixes for USB-audio,
HD-audio and Firewire. The USB-audio fix is the respin of the previous
race fix after a revert due to the regression"
* tag 'sound-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
Revert "ALSA: firewire-lib: change structure member with proper type"
ALSA: usb-audio: test EP_FLAG_RUNNING at urb completion
ALSA: usb-audio: Fix irq/process data synchronization
ALSA: hda - Apply asus-mode8 fixup to ASUS X71SL
ALSA: hda - Fix up GPIO for ASUS ROG Ranger
ALSA: firewire-lib: change structure member with proper type
ALSA: firewire-tascam: Fix to handle error from initialization of stream data
ALSA: fireworks: fix asymmetric API call at unit removal
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One fix for a broken driver on Renesas RZ/A1 SoCs with bootloaders
that don't turn all the clks on and another fix for stm32f4 SoCs where
we have multiple drivers attaching to the same DT node"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: stm32f4: Use CLK_OF_DECLARE_DRIVER initialization method
clk: renesas: mstp: Support 8-bit registers for r7s72100
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix temp1_max_alarm attribute in lm90 driver"
* tag 'hwmon-for-linus-v4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (lm90) fix temp1_max_alarm attribute
|
|
Pull KVM fixes from Radim Krčmář:
"MIPS:
- fix host kernel crashes when receiving a signal with 64-bit
userspace
- flush instruction cache on all vcpus after generating entry code
(both for stable)
x86:
- fix NULL dereference in MMU caused by SMM transitions (for stable)
- correct guest instruction pointer after emulating some VMX errors
- minor cleanup"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: remove duplicated declaration
KVM: MIPS: Flush KVM entry code from icache globally
KVM: MIPS: Don't clobber CP0_Status.UX
KVM: x86: reset MMU on KVM_SET_VCPU_EVENTS
KVM: nVMX: fix instruction skipping during emulated vm-entry
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- re-introduce the arm64 get_current() optimisation
- KERN_CONT fallout fix in show_pte()
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: restore get_current() optimisation
arm64: mm: fix show_pte KERN_CONT fallout
|
|
Port of radeon change to amdgpu.
Acked-by: Edward O'Callaghan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=98897
https://bugs.launchpad.net/bugs/1651981
Acked-by: Edward O'Callaghan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
Cc: Adrian Fiergolski <[email protected]>
|
|
Use the appropriate smc firmware for each chip revision.
Using the wrong one can cause stability issues.
Acked-by: Edward O'Callaghan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
Use the appropriate smc firmware for each chip revision.
Using the wrong one can cause stability issues.
Acked-by: Edward O'Callaghan <[email protected]>
Signed-off-by: Flora Cui <[email protected]>
Reviewed-by: Junwei Zhang <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
Signed-off-by: Rex Zhu <[email protected]>
Reviewed-by: Alex Deucher <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|