| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Unlike x86, which has machinery to deal with page faults that occur
during the execution of EFI runtime services, arm64 has nothing like
that, and a synchronous exception raised by firmware code brings down
the whole system.
With more EFI based systems appearing that were not built to run Linux
(such as the Windows-on-ARM laptops based on Qualcomm SOCs), as well as
the introduction of PRM (platform specific firmware routines that are
callable just like EFI runtime services), we are more likely to run into
issues of this sort, and it is much more likely that we can identify and
work around such issues if they don't bring down the system entirely.
Since we already use a EFI runtime services call wrapper in assembler,
we can quite easily add some code that captures the execution state at
the point where the call is made, allowing us to revert to this state
and proceed execution if the call triggered a synchronous exception.
Given that the kernel and the firmware don't share any data structures
that could end up in an indeterminate state, we can happily continue
running, as long as we mark the EFI runtime services as unavailable from
that point on.
Signed-off-by: Ard Biesheuvel <[email protected]>
Acked-by: Catalin Marinas <[email protected]>
|
|
Swap the 1st and 2nd arguments to be consistent with the usage of
kvcalloc().
Fixes: c9b8fecddb5b ("KVM: use kvcalloc for array allocations")
Signed-off-by: Liao Chang <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
kvm_zap_gfn_range() must be called in an SRCU read-critical section, but
there is no SRCU annotation in __kvm_set_or_clear_apicv_inhibit(). This
can lead to the following warning via
kvm_arch_vcpu_ioctl_set_guest_debug() if a Shadow MMU is in use (TDP
MMU disabled or nesting):
[ 1416.659809] =============================
[ 1416.659810] WARNING: suspicious RCU usage
[ 1416.659839] 6.1.0-dbg-DEV #1 Tainted: G S I
[ 1416.659853] -----------------------------
[ 1416.659854] include/linux/kvm_host.h:954 suspicious rcu_dereference_check() usage!
[ 1416.659856]
...
[ 1416.659904] dump_stack_lvl+0x84/0xaa
[ 1416.659910] dump_stack+0x10/0x15
[ 1416.659913] lockdep_rcu_suspicious+0x11e/0x130
[ 1416.659919] kvm_zap_gfn_range+0x226/0x5e0
[ 1416.659926] ? kvm_make_all_cpus_request_except+0x18b/0x1e0
[ 1416.659935] __kvm_set_or_clear_apicv_inhibit+0xcc/0x100
[ 1416.659940] kvm_arch_vcpu_ioctl_set_guest_debug+0x350/0x390
[ 1416.659946] kvm_vcpu_ioctl+0x2fc/0x620
[ 1416.659955] __se_sys_ioctl+0x77/0xc0
[ 1416.659962] __x64_sys_ioctl+0x1d/0x20
[ 1416.659965] do_syscall_64+0x3d/0x80
[ 1416.659969] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Always take the KVM SRCU read lock in __kvm_set_or_clear_apicv_inhibit()
to protect the GFN to memslot translation. The SRCU read lock is not
technically required when no Shadow MMUs are in use, since the TDP MMU
walks the paging structures from the roots and does not need to look up
GFN translations in the memslots, but make the SRCU locking
unconditional for simplicty.
In most cases, the SRCU locking is taken care of in the vCPU run loop,
but when called through other ioctls (such as KVM_SET_GUEST_DEBUG)
there is no srcu_read_lock.
Tested: ran tools/testing/selftests/kvm/x86_64/debug_regs on a DBG
build. This patch causes the suspicious RCU warning to disappear.
Note that the warning is hit in __kvm_zap_rmaps(), so
kvm_memslots_have_rmaps() must return true in order for this to
repro (i.e. the TDP MMU must be off or nesting in use.)
Reported-by: Greg Thelen <[email protected]>
Fixes: 36222b117e36 ("KVM: x86: don't disable APICv memslot when inhibited")
Signed-off-by: Ben Gardon <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
Dexuan Cui says:
====================
vsock: remove an unused variable and fix infinite sleep
Patch 1 removes the unused 'wait' variable.
Patch 2 fixes an infinite sleep issue reported by a hv_sock user.
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Currently vsock_connectible_has_data() may miss a wakeup operation
between vsock_connectible_has_data() == 0 and the prepare_to_wait().
Fix the race by adding the process to the wait queue before checking
vsock_connectible_has_data().
Fixes: b3f7fd54881b ("af_vsock: separate wait data loop")
Signed-off-by: Dexuan Cui <[email protected]>
Reviewed-by: Stefano Garzarella <[email protected]>
Reported-by: Frédéric Dalleau <[email protected]>
Tested-by: Frédéric Dalleau <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Remove the unused variable introduced by 19c1b90e1979.
Fixes: 19c1b90e1979 ("af_vsock: separate receive data loop")
Signed-off-by: Dexuan Cui <[email protected]>
Reviewed-by: Stefano Garzarella <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
xen_enable_sysenter() and xen_enable_syscall() can be simplified a lot.
While at it, switch to use cpu_feature_enabled() instead of
boot_cpu_has().
Signed-off-by: Juergen Gross <[email protected]>
|
|
Commit 8714f7bcd3c2 ("xen/pv: add fault recovery control to pmu msr
accesses") introduced code resulting in a warning issued by the smatch
static checker, claiming to use an uninitialized variable.
This is a false positive, but work around the warning nevertheless.
Fixes: 8714f7bcd3c2 ("xen/pv: add fault recovery control to pmu msr accesses")
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v6.1-rc4:
- Small fixes to make rockchip work better.
- Fix imx Kconfig.
- Small fix to imx' mode_valid.
Signed-off-by: Dave Airlie <[email protected]>
From: Maarten Lankhorst <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
KASAN reported a use-after-free with ftrace ops [1]. It was found from
vmcore that perf had registered two ops with the same content
successively, both dynamic. After unregistering the second ops, a
use-after-free occurred.
In ftrace_shutdown(), when the second ops is unregistered, the
FTRACE_UPDATE_CALLS command is not set because there is another enabled
ops with the same content. Also, both ops are dynamic and the ftrace
callback function is ftrace_ops_list_func, so the
FTRACE_UPDATE_TRACE_FUNC command will not be set. Eventually the value
of 'command' will be 0 and ftrace_shutdown() will skip the rcu
synchronization.
However, ftrace may be activated. When the ops is released, another CPU
may be accessing the ops. Add the missing synchronization to fix this
problem.
[1]
BUG: KASAN: use-after-free in __ftrace_ops_list_func kernel/trace/ftrace.c:7020 [inline]
BUG: KASAN: use-after-free in ftrace_ops_list_func+0x2b0/0x31c kernel/trace/ftrace.c:7049
Read of size 8 at addr ffff56551965bbc8 by task syz-executor.2/14468
CPU: 1 PID: 14468 Comm: syz-executor.2 Not tainted 5.10.0 #7
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x40c arch/arm64/kernel/stacktrace.c:132
show_stack+0x30/0x40 arch/arm64/kernel/stacktrace.c:196
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1b4/0x248 lib/dump_stack.c:118
print_address_description.constprop.0+0x28/0x48c mm/kasan/report.c:387
__kasan_report mm/kasan/report.c:547 [inline]
kasan_report+0x118/0x210 mm/kasan/report.c:564
check_memory_region_inline mm/kasan/generic.c:187 [inline]
__asan_load8+0x98/0xc0 mm/kasan/generic.c:253
__ftrace_ops_list_func kernel/trace/ftrace.c:7020 [inline]
ftrace_ops_list_func+0x2b0/0x31c kernel/trace/ftrace.c:7049
ftrace_graph_call+0x0/0x4
__might_sleep+0x8/0x100 include/linux/perf_event.h:1170
__might_fault mm/memory.c:5183 [inline]
__might_fault+0x58/0x70 mm/memory.c:5171
do_strncpy_from_user lib/strncpy_from_user.c:41 [inline]
strncpy_from_user+0x1f4/0x4b0 lib/strncpy_from_user.c:139
getname_flags+0xb0/0x31c fs/namei.c:149
getname+0x2c/0x40 fs/namei.c:209
[...]
Allocated by task 14445:
kasan_save_stack+0x24/0x50 mm/kasan/common.c:48
kasan_set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc mm/kasan/common.c:479 [inline]
__kasan_kmalloc.constprop.0+0x110/0x13c mm/kasan/common.c:449
kasan_kmalloc+0xc/0x14 mm/kasan/common.c:493
kmem_cache_alloc_trace+0x440/0x924 mm/slub.c:2950
kmalloc include/linux/slab.h:563 [inline]
kzalloc include/linux/slab.h:675 [inline]
perf_event_alloc.part.0+0xb4/0x1350 kernel/events/core.c:11230
perf_event_alloc kernel/events/core.c:11733 [inline]
__do_sys_perf_event_open kernel/events/core.c:11831 [inline]
__se_sys_perf_event_open+0x550/0x15f4 kernel/events/core.c:11723
__arm64_sys_perf_event_open+0x6c/0x80 kernel/events/core.c:11723
[...]
Freed by task 14445:
kasan_save_stack+0x24/0x50 mm/kasan/common.c:48
kasan_set_track+0x24/0x34 mm/kasan/common.c:56
kasan_set_free_info+0x20/0x40 mm/kasan/generic.c:358
__kasan_slab_free.part.0+0x11c/0x1b0 mm/kasan/common.c:437
__kasan_slab_free mm/kasan/common.c:445 [inline]
kasan_slab_free+0x2c/0x40 mm/kasan/common.c:446
slab_free_hook mm/slub.c:1569 [inline]
slab_free_freelist_hook mm/slub.c:1608 [inline]
slab_free mm/slub.c:3179 [inline]
kfree+0x12c/0xc10 mm/slub.c:4176
perf_event_alloc.part.0+0xa0c/0x1350 kernel/events/core.c:11434
perf_event_alloc kernel/events/core.c:11733 [inline]
__do_sys_perf_event_open kernel/events/core.c:11831 [inline]
__se_sys_perf_event_open+0x550/0x15f4 kernel/events/core.c:11723
[...]
Link: https://lore.kernel.org/linux-trace-kernel/[email protected]
Fixes: edb096e00724f ("ftrace: Fix memleak when unregistering dynamic ops when tracing disabled")
Cc: [email protected]
Suggested-by: Steven Rostedt <[email protected]>
Signed-off-by: Li Huafei <[email protected]>
Signed-off-by: Steven Rostedt (Google) <[email protected]>
|
|
On some machines the number of listed CPUs may be bigger than the actual
CPUs that exist. The tracing subsystem allocates a per_cpu directory with
access to the per CPU ring buffer via a cpuX file. But to save space, the
ring buffer will only allocate buffers for online CPUs, even though the
CPU array will be as big as the nr_cpu_ids.
With the addition of waking waiters on the ring buffer when closing the
file, the ring_buffer_wake_waiters() now needs to make sure that the
buffer is allocated (with the irq_work allocated with it) before trying to
wake waiters, as it will cause a NULL pointer dereference.
While debugging this, I added a NULL check for the buffer itself (which is
OK to do), and also NULL pointer checks against buffer->buffers (which is
not fine, and will WARN) as well as making sure the CPU number passed in
is within the nr_cpu_ids (which is also not fine if it isn't).
Link: https://lore.kernel.org/all/[email protected]/
Link: https://lore.kernel.org/all/CAM6Wdxc0KRJMXVAA0Y=u6Jh2V=uWB-_Fn6M4xRuNppfXzL1mUg@mail.gmail.com/
Link: https://lkml.kernel.org/linux-trace-kernel/[email protected]
Cc: [email protected]
Cc: Steven Noonan <[email protected]>
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=1204705
Reported-by: Takashi Iwai <[email protected]>
Reported-by: Roland Ruckerbauer <[email protected]>
Fixes: f3ddb74ad079 ("tracing: Wake up ring buffer waiters on closing of the file")
Reviewed-by: Masami Hiramatsu (Google) <[email protected]>
Signed-off-by: Steven Rostedt (Google) <[email protected]>
|
|
During the initialization of ip6_route_net_init_late(), if file
ipv6_route or rt6_stats fails to be created, the initialization is
successful by default. Therefore, the ipv6_route or rt6_stats file
doesn't be found during the remove in ip6_route_net_exit_late(). It
will cause WRNING.
The following is the stack information:
name 'rt6_stats'
WARNING: CPU: 0 PID: 9 at fs/proc/generic.c:712 remove_proc_entry+0x389/0x460
Modules linked in:
Workqueue: netns cleanup_net
RIP: 0010:remove_proc_entry+0x389/0x460
PKRU: 55555554
Call Trace:
<TASK>
ops_exit_list+0xb0/0x170
cleanup_net+0x4ea/0xb00
process_one_work+0x9bf/0x1710
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Fixes: cdb1876192db ("[NETNS][IPV6] route6 - create route6 proc files for the namespace")
Signed-off-by: Zhengchao Shao <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The following commands should result in all the dynamic FDB entries
being flushed, but instead all the non-local (non-permanent) entries are
flushed:
# bridge fdb add 00:aa:bb:cc:dd:ee dev dummy1 master static
# bridge fdb add 00:11:22:33:44:55 dev dummy1 master dynamic
# ip link set dev br0 type bridge fdb_flush
# bridge fdb show brport dummy1
00:00:00:00:00:01 master br0 permanent
33:33:00:00:00:01 self permanent
01:00:5e:00:00:01 self permanent
This is because br_fdb_flush() works with FDB flags and not the
corresponding enumerator values. Fix by passing the FDB flag instead.
After the fix:
# bridge fdb add 00:aa:bb:cc:dd:ee dev dummy1 master static
# bridge fdb add 00:11:22:33:44:55 dev dummy1 master dynamic
# ip link set dev br0 type bridge fdb_flush
# bridge fdb show brport dummy1
00:aa:bb:cc:dd:ee master br0 static
00:00:00:00:00:01 master br0 permanent
33:33:00:00:00:01 self permanent
01:00:5e:00:00:01 self permanent
Fixes: 1f78ee14eeac ("net: bridge: fdb: add support for fine-grained flushing")
Signed-off-by: Ido Schimmel <[email protected]>
Acked-by: Nikolay Aleksandrov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
When IPv6 module gets initialized but hits an error in the middle,
kenel panic with:
KASAN: null-ptr-deref in range [0x0000000000000598-0x000000000000059f]
CPU: 1 PID: 361 Comm: insmod
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:__neigh_ifdown.isra.0+0x24b/0x370
RSP: 0018:ffff888012677908 EFLAGS: 00000202
...
Call Trace:
<TASK>
neigh_table_clear+0x94/0x2d0
ndisc_cleanup+0x27/0x40 [ipv6]
inet6_init+0x21c/0x2cb [ipv6]
do_one_initcall+0xd3/0x4d0
do_init_module+0x1ae/0x670
...
Kernel panic - not syncing: Fatal exception
When ipv6 initialization fails, it will try to cleanup and calls:
neigh_table_clear()
neigh_ifdown(tbl, NULL)
pneigh_queue_purge(&tbl->proxy_queue, dev_net(dev == NULL))
# dev_net(NULL) triggers null-ptr-deref.
Fix it by passing NULL to pneigh_queue_purge() in neigh_ifdown() if dev
is NULL, to make kernel not panic immediately.
Fixes: 66ba215cb513 ("neigh: fix possible DoS due to net iface start/stop loop")
Signed-off-by: Chen Zhongjin <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Reviewed-by: Denis V. Lunev <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In smc_init(), register_pernet_subsys(&smc_net_stat_ops) is called
without any error handling.
If it fails, registering of &smc_net_ops won't be reverted.
And if smc_nl_init() fails, &smc_net_stat_ops itself won't be reverted.
This leaves wild ops in subsystem linkedlist and when another module
tries to call register_pernet_operations() it triggers page fault:
BUG: unable to handle page fault for address: fffffbfff81b964c
RIP: 0010:register_pernet_operations+0x1b9/0x5f0
Call Trace:
<TASK>
register_pernet_subsys+0x29/0x40
ebtables_init+0x58/0x1000 [ebtables]
...
Fixes: 194730a9beb5 ("net/smc: Make SMC statistics network namespace aware")
Signed-off-by: Chen Zhongjin <[email protected]>
Reviewed-by: Tony Lu <[email protected]>
Reviewed-by: Wenjia Zhang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In current code "plat->mdio_node" is always NULL, the mdio
support is lost as there is no "mdio_bus_data". The original
driver could work as the "mdio" variable is never set to
false, which is described in commit <b0e03950dd71> ("stmmac:
dwmac-loongson: fix uninitialized variable ......"). And
after this commit merged, the "mdio" variable is always
false, causing the mdio supoort logic lost.
Fixes: 30bba69d7db4 ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Liu Peibao <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Free the rwi structure in the event that the last rwi in the list
processed successfully. The logic in commit 4f408e1fa6e1 ("ibmvnic:
retry reset if there are no other resets") introduces an issue that
results in a 32 byte memory leak whenever the last rwi in the list
gets processed.
Fixes: 4f408e1fa6e1 ("ibmvnic: retry reset if there are no other resets")
Signed-off-by: Nick Child <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in drivers/net/phy/mdio_bus.c:586:27
left shift of 1 by 31 places cannot be represented in type 'int'
Call Trace:
<TASK>
dump_stack_lvl+0x7d/0xa5
dump_stack+0x15/0x1b
ubsan_epilogue+0xe/0x4e
__ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
__mdiobus_register+0x49d/0x4e0
fixed_mdio_bus_init+0xd8/0x12d
do_one_initcall+0x76/0x430
kernel_init_freeable+0x3b3/0x422
kernel_init+0x24/0x1e0
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 4fd5f812c23c ("phylib: allow incremental scanning of an mii bus")
Signed-off-by: Gaosheng Cui <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
1) netlink socket notifier might win race to release objects that are
already pending to be released via commit release path, reported by
syzbot.
2) No need to postpone flow rule release to commit release path, this
triggered the syzbot report, complementary fix to previous patch.
3) Use explicit signed chars in IPVS to unbreak arm, from Jason A. Donenfeld.
4) Missing check for proc entry creation failure in IPVS, from Zhengchao Shao.
5) Incorrect error path handling when BPF NAT fails to register, from
Chen Zhongjin.
6) Prevent huge memory allocation in ipset hash types, from Jozsef Kadlecsik.
Except the incorrect BPF NAT error path which is broken in 6.1-rc, anything
else has been broken for several releases.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: ipset: enforce documented limit to prevent allocating huge memory
netfilter: nf_nat: Fix possible memory leak in nf_nat_init()
ipvs: fix WARNING in ip_vs_app_net_cleanup()
ipvs: fix WARNING in __ip_vs_cleanup_batch()
ipvs: use explicitly signed chars
netfilter: nf_tables: release flow rule object from commit path
netfilter: nf_tables: netlink notifier might race to release objects
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth 2022-11-02
- Fix memory leak in hci_vhci driver
- Fix handling of skb on virtio_bt driver
- Fix accepting connection for invalid L2CAP PSM
- Fix attemting to access uninitialized memory
- Fix use-after-free in l2cap_reassemble_sdu
- Fix use-after-free in l2cap_conn_del
- Fix handling of destination address type for CIS
- Fix not restoring ISO buffer count on disconnect
* tag 'for-net-2022-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: Fix attempting to access uninitialized memory
Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm
Bluetooth: L2CAP: Fix accepting connection request for invalid SPSM
Bluetooth: hci_conn: Fix not restoring ISO buffer count on disconnect
Bluetooth: L2CAP: Fix memory leak in vhci_write
Bluetooth: L2CAP: fix use-after-free in l2cap_conn_del()
Bluetooth: virtio_bt: Use skb_put to set length
Bluetooth: hci_conn: Fix CIS connection dst_type handling
Bluetooth: L2CAP: Fix use-after-free caused by l2cap_reassemble_sdu
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
On l2cap_parse_conf_req the variable efs is only initialized if
remote_efs has been set.
CVE: CVE-2022-42895
CC: [email protected]
Reported-by: Tamás Koczka <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Reviewed-by: Tedd Ho-Jeong An <[email protected]>
|
|
l2cap_global_chan_by_psm shall not return fixed channels as they are not
meant to be connected by (S)PSM.
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Reviewed-by: Tedd Ho-Jeong An <[email protected]>
|
|
The Bluetooth spec states that the valid range for SPSM is from
0x0001-0x00ff so it is invalid to accept values outside of this range:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 3, Part A
page 1059:
Table 4.15: L2CAP_LE_CREDIT_BASED_CONNECTION_REQ SPSM ranges
CVE: CVE-2022-42896
CC: [email protected]
Reported-by: Tamás Koczka <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Reviewed-by: Tedd Ho-Jeong An <[email protected]>
|
|
With corresponding FW change fixes issue where triggering CWSR on a
workgroup with waves in s_barrier wouldn't lead to a back-off and
therefore cause a hang.
Signed-off-by: Jay Cornwall <[email protected]>
Tested-by: Graham Sider <[email protected]>
Acked-by: Harish Kasiviswanathan <[email protected]>
Acked-by: Felix Kuehling <[email protected]>
Reviewed-by: Graham Sider <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected] # 6.0.x
|
|
[Why]
Fix for some of the tool reported modes for FCLK
P-state deviations and UCLK P-state deviations that
are coming from DSC terms and/or Scaling terms
causing MinActiveFCLKChangeLatencySupported
and MaxActiveDRAMClockChangeLatencySupported
incorrectly calculated in DML for these configurations.
Reviewed-by: Chaitanya Dhere <[email protected]>
Acked-by: Jasdeep Dhillon <[email protected]>
Acked-by: Alex Hung <[email protected]>
Signed-off-by: Nevenko Stupar <[email protected]>
Tested-by: Mark Broadworth <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Certain 4K high refresh rate modes requiring DSC are exhibiting top
of screen underflow corruption. Increasing the DSC delay by a factor
of 6 percent stops the underflow for most use cases.
[How]
Multiply DSC delay requirement in DML by a factor.
Add debug option to make this DSC delay factor configurable.
Reviewed-by: Alvin Lee <[email protected]>
Acked-by: Alex Hung <[email protected]>
Signed-off-by: George Shen <[email protected]>
Tested-by: Mark Broadworth <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
The DST_after_scaler value that DML spreadsheet outputs is
generally the driver value round up to the nearest int.
Reviewed-by: Alvin Lee <[email protected]>
Acked-by: Alex Hung <[email protected]>
Signed-off-by: George Shen <[email protected]>
Tested-by: Mark Broadworth <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
DSC config is calculated separately from DML calculations.
DML should use these separately calculated DSC params. The issue is
that the calculated bpp is not properly propagated into DML.
[How]
Correctly used forced_bpp value in DML.
Reviewed-by: Alvin Lee <[email protected]>
Acked-by: Alex Hung <[email protected]>
Signed-off-by: George Shen <[email protected]>
Tested-by: Mark Broadworth <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
DCN32 DSC delay calculation had an unintentional integer division,
resulting in a mismatch against the DML spreadsheet.
[How]
Cast numerator to double before performing the division.
Reviewed-by: Alvin Lee <[email protected]>
Acked-by: Alex Hung <[email protected]>
Signed-off-by: George Shen <[email protected]>
Tested-by: Mark Broadworth <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
The recent change brought a bug on SRIOV envrionment. It caused
unloading amdgpu failed on Guest VM. The reason is that the VF
FLR was requested while unloading amdgpu driver, but the VF FLR
of SRIOV sequence is wrong while removing PCI device.
For SRIOV, the guest driver should not trigger the whole XGMI hive
to do the reset. Host driver control how the device been reset.
Fixes: f5c7e7797060 ("drm/amdgpu: Adjust removal control flow for smu v13_0_2")
Acked-by: Alex Deucher <[email protected]>
Reviewed-by: Shaoyun Liu <[email protected]>
Signed-off-by: Gavin Wan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Temporary workaround to fix issues observed in some compute applications
when GFXOFF is enabled on GFX11.
Signed-off-by: Graham Sider <[email protected]>
Acked-by: Alex Deucher <[email protected]>
Reviewed-by: Harish Kasiviswanathan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected] # 6.0.x
|
|
When disconnecting an ISO link the controller may not generate
HCI_EV_NUM_COMP_PKTS for unacked packets which needs to be restored in
hci_conn_del otherwise the host would assume they are still in use and
would not be able to use all the buffers available.
Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Tested-by: Frédéric Danis <[email protected]>
|
|
Syzkaller reports a memory leak as follows:
====================================
BUG: memory leak
unreferenced object 0xffff88810d81ac00 (size 240):
[...]
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff838733d9>] __alloc_skb+0x1f9/0x270 net/core/skbuff.c:418
[<ffffffff833f742f>] alloc_skb include/linux/skbuff.h:1257 [inline]
[<ffffffff833f742f>] bt_skb_alloc include/net/bluetooth/bluetooth.h:469 [inline]
[<ffffffff833f742f>] vhci_get_user drivers/bluetooth/hci_vhci.c:391 [inline]
[<ffffffff833f742f>] vhci_write+0x5f/0x230 drivers/bluetooth/hci_vhci.c:511
[<ffffffff815e398d>] call_write_iter include/linux/fs.h:2192 [inline]
[<ffffffff815e398d>] new_sync_write fs/read_write.c:491 [inline]
[<ffffffff815e398d>] vfs_write+0x42d/0x540 fs/read_write.c:578
[<ffffffff815e3cdd>] ksys_write+0x9d/0x160 fs/read_write.c:631
[<ffffffff845e0645>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff845e0645>] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
[<ffffffff84600087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
====================================
HCI core will uses hci_rx_work() to process frame, which is queued to
the hdev->rx_q tail in hci_recv_frame() by HCI driver.
Yet the problem is that, HCI core may not free the skb after handling
ACL data packets. To be more specific, when start fragment does not
contain the L2CAP length, HCI core just copies skb into conn->rx_skb and
finishes frame process in l2cap_recv_acldata(), without freeing the skb,
which triggers the above memory leak.
This patch solves it by releasing the relative skb, after processing
the above case in l2cap_recv_acldata().
Fixes: 4d7ea8ee90e4 ("Bluetooth: L2CAP: Fix handling fragmented length")
Link: https://lore.kernel.org/all/[email protected]/
Reported-and-tested-by: [email protected]
Signed-off-by: Hawkins Jiawei <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
When l2cap_recv_frame() is invoked to receive data, and the cid is
L2CAP_CID_A2MP, if the channel does not exist, it will create a channel.
However, after a channel is created, the hold operation of the channel
is not performed. In this case, the value of channel reference counting
is 1. As a result, after hci_error_reset() is triggered, l2cap_conn_del()
invokes the close hook function of A2MP to release the channel. Then
l2cap_chan_unlock(chan) will trigger UAF issue.
The process is as follows:
Receive data:
l2cap_data_channel()
a2mp_channel_create() --->channel ref is 2
l2cap_chan_put() --->channel ref is 1
Triger event:
hci_error_reset()
hci_dev_do_close()
...
l2cap_disconn_cfm()
l2cap_conn_del()
l2cap_chan_hold() --->channel ref is 2
l2cap_chan_del() --->channel ref is 1
a2mp_chan_close_cb() --->channel ref is 0, release channel
l2cap_chan_unlock() --->UAF of channel
The detailed Call Trace is as follows:
BUG: KASAN: use-after-free in __mutex_unlock_slowpath+0xa6/0x5e0
Read of size 8 at addr ffff8880160664b8 by task kworker/u11:1/7593
Workqueue: hci0 hci_error_reset
Call Trace:
<TASK>
dump_stack_lvl+0xcd/0x134
print_report.cold+0x2ba/0x719
kasan_report+0xb1/0x1e0
kasan_check_range+0x140/0x190
__mutex_unlock_slowpath+0xa6/0x5e0
l2cap_conn_del+0x404/0x7b0
l2cap_disconn_cfm+0x8c/0xc0
hci_conn_hash_flush+0x11f/0x260
hci_dev_close_sync+0x5f5/0x11f0
hci_dev_do_close+0x2d/0x70
hci_error_reset+0x9e/0x140
process_one_work+0x98a/0x1620
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Allocated by task 7593:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0xa9/0xd0
l2cap_chan_create+0x40/0x930
amp_mgr_create+0x96/0x990
a2mp_channel_create+0x7d/0x150
l2cap_recv_frame+0x51b8/0x9a70
l2cap_recv_acldata+0xaa3/0xc00
hci_rx_work+0x702/0x1220
process_one_work+0x98a/0x1620
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
Freed by task 7593:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_set_free_info+0x20/0x30
____kasan_slab_free+0x167/0x1c0
slab_free_freelist_hook+0x89/0x1c0
kfree+0xe2/0x580
l2cap_chan_put+0x22a/0x2d0
l2cap_conn_del+0x3fc/0x7b0
l2cap_disconn_cfm+0x8c/0xc0
hci_conn_hash_flush+0x11f/0x260
hci_dev_close_sync+0x5f5/0x11f0
hci_dev_do_close+0x2d/0x70
hci_error_reset+0x9e/0x140
process_one_work+0x98a/0x1620
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
Last potentially related work creation:
kasan_save_stack+0x1e/0x40
__kasan_record_aux_stack+0xbe/0xd0
call_rcu+0x99/0x740
netlink_release+0xe6a/0x1cf0
__sock_release+0xcd/0x280
sock_close+0x18/0x20
__fput+0x27c/0xa90
task_work_run+0xdd/0x1a0
exit_to_user_mode_prepare+0x23c/0x250
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x42/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Second to last potentially related work creation:
kasan_save_stack+0x1e/0x40
__kasan_record_aux_stack+0xbe/0xd0
call_rcu+0x99/0x740
netlink_release+0xe6a/0x1cf0
__sock_release+0xcd/0x280
sock_close+0x18/0x20
__fput+0x27c/0xa90
task_work_run+0xdd/0x1a0
exit_to_user_mode_prepare+0x23c/0x250
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x42/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: d0be8347c623 ("Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put")
Signed-off-by: Zhengchao Shao <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
By using skb_put we ensure that skb->tail is set
correctly. Currently, skb->tail is always zero, which
leads to errors, such as the following page fault in
rfcomm_recv_frame:
BUG: unable to handle page fault for address: ffffed1021de29ff
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
RIP: 0010:rfcomm_run+0x831/0x4040 (net/bluetooth/rfcomm/core.c:1751)
Fixes: afd2daa26c7a ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: Soenke Huster <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
hci_connect_cis and iso_connect_cis call hci_bind_cis inconsistently
with dst_type being either ISO socket address type or the HCI type, but
these values cannot be mixed like this. Fix this by using only the HCI
type.
CIS connection dst_type was also not initialized in hci_bind_cis, even
though it is used in hci_conn_hash_lookup_cis to find existing
connections. Set the value in hci_bind_cis, so that existing CIS
connections are found e.g. when doing deferred socket connections, also
when dst_type is not 0 (ADDR_LE_DEV_PUBLIC).
Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Fix the race condition between the following two flows that run in
parallel:
1. l2cap_reassemble_sdu -> chan->ops->recv (l2cap_sock_recv_cb) ->
__sock_queue_rcv_skb.
2. bt_sock_recvmsg -> skb_recv_datagram, skb_free_datagram.
An SKB can be queued by the first flow and immediately dequeued and
freed by the second flow, therefore the callers of l2cap_reassemble_sdu
can't use the SKB after that function returns. However, some places
continue accessing struct l2cap_ctrl that resides in the SKB's CB for a
short time after l2cap_reassemble_sdu returns, leading to a
use-after-free condition (the stack trace is below, line numbers for
kernel 5.19.8).
Fix it by keeping a local copy of struct l2cap_ctrl.
BUG: KASAN: use-after-free in l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
Read of size 1 at addr ffff88812025f2f0 by task kworker/u17:3/43169
Workqueue: hci0 hci_rx_work [bluetooth]
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:107 (discriminator 4))
print_report.cold (mm/kasan/report.c:314 mm/kasan/report.c:429)
? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
kasan_report (mm/kasan/report.c:162 mm/kasan/report.c:493)
? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
l2cap_rx (net/bluetooth/l2cap_core.c:7236 net/bluetooth/l2cap_core.c:7271) bluetooth
ret_from_fork (arch/x86/entry/entry_64.S:306)
</TASK>
Allocated by task 43169:
kasan_save_stack (mm/kasan/common.c:39)
__kasan_slab_alloc (mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:469)
kmem_cache_alloc_node (mm/slab.h:750 mm/slub.c:3243 mm/slub.c:3293)
__alloc_skb (net/core/skbuff.c:414)
l2cap_recv_frag (./include/net/bluetooth/bluetooth.h:425 net/bluetooth/l2cap_core.c:8329) bluetooth
l2cap_recv_acldata (net/bluetooth/l2cap_core.c:8442) bluetooth
hci_rx_work (net/bluetooth/hci_core.c:3642 net/bluetooth/hci_core.c:3832) bluetooth
process_one_work (kernel/workqueue.c:2289)
worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2437)
kthread (kernel/kthread.c:376)
ret_from_fork (arch/x86/entry/entry_64.S:306)
Freed by task 27920:
kasan_save_stack (mm/kasan/common.c:39)
kasan_set_track (mm/kasan/common.c:45)
kasan_set_free_info (mm/kasan/generic.c:372)
____kasan_slab_free (mm/kasan/common.c:368 mm/kasan/common.c:328)
slab_free_freelist_hook (mm/slub.c:1780)
kmem_cache_free (mm/slub.c:3536 mm/slub.c:3553)
skb_free_datagram (./include/net/sock.h:1578 ./include/net/sock.h:1639 net/core/datagram.c:323)
bt_sock_recvmsg (net/bluetooth/af_bluetooth.c:295) bluetooth
l2cap_sock_recvmsg (net/bluetooth/l2cap_sock.c:1212) bluetooth
sock_read_iter (net/socket.c:1087)
new_sync_read (./include/linux/fs.h:2052 fs/read_write.c:401)
vfs_read (fs/read_write.c:482)
ksys_read (fs/read_write.c:620)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
Link: https://lore.kernel.org/linux-bluetooth/CAKErNvoqga1WcmoR3-0875esY6TVWFQDandbVZncSiuGPBQXLA@mail.gmail.com/T/#u
Fixes: d2a7ac5d5d3a ("Bluetooth: Add the ERTM receive state machine")
Fixes: 4b51dae96731 ("Bluetooth: Add streaming mode receive and incoming packet classifier")
Signed-off-by: Maxim Mikityanskiy <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
If a system does not have swap and memory is under 100% usage,
amdgpu will fail to evict resources. Currently the suspend
carries on proceeding to reset the GPU:
```
[drm] evicting device resources failed
[drm:amdgpu_device_ip_suspend_phase2 [amdgpu]] *ERROR* suspend of IP block <vcn_v3_0> failed -12
[drm] free PSP TMR buffer
[TTM] Failed allocating page table
[drm] evicting device resources failed
amdgpu 0000:03:00.0: amdgpu: MODE1 reset
amdgpu 0000:03:00.0: amdgpu: GPU mode1 reset
amdgpu 0000:03:00.0: amdgpu: GPU smu mode1 reset
```
At this point if the suspend actually succeeded I think that amdgpu
would have recovered because the GPU would have power cut off and
restored. However the kernel fails to continue the suspend from the
memory pressure and amdgpu fails to run the "resume" from the aborted
suspend.
```
ACPI: PM: Preparing to enter system sleep state S3
SLUB: Unable to allocate memory on node -1, gfp=0xdc0(GFP_KERNEL|__GFP_ZERO)
cache: Acpi-State, object size: 80, buffer size: 80, default order: 0, min order: 0
node 0: slabs: 22, objs: 1122, free: 0
ACPI Error: AE_NO_MEMORY, Could not update object reference count (20210730/utdelete-651)
[drm:psp_hw_start [amdgpu]] *ERROR* PSP load kdb failed!
[drm:psp_resume [amdgpu]] *ERROR* PSP resume failed
[drm:amdgpu_device_fw_loading [amdgpu]] *ERROR* resume of IP block <psp> failed -62
amdgpu 0000:03:00.0: amdgpu: amdgpu_device_ip_resume failed (-62).
PM: dpm_run_callback(): pci_pm_resume+0x0/0x100 returns -62
amdgpu 0000:03:00.0: PM: failed to resume async: error -62
```
To avoid this series of unfortunate events, fail amdgpu's suspend
when the memory eviction fails. This will let the system gracefully
recover and the user can try suspend again when the memory pressure
is relieved.
Reported-by: [email protected]
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2223
Signed-off-by: Mario Limonciello <[email protected]>
Reviewed-by: Alex Deucher <[email protected]>
Acked-by: Christian König <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Armv8 Juno fix for v6.1
Just a single fix to add the missing critical points in the thermal
zones that has been mandatory in the binding but was enforced in the
code recently.
* tag 'juno-fix-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Add thermal critical trip points
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
./drivers/gpu/drm/amd/amdkfd/kfd_migrate.c:985:58-62: ERROR: p is NULL but dereferenced.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2549
Reported-by: Abaci Robot <[email protected]>
Signed-off-by: Yang Li <[email protected]>
Reviewed-by: Felix Kuehling <[email protected]>
Signed-off-by: Felix Kuehling <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
Use mes.sched_version, mes.kiq_version for debugfs as
mes.ucode_fw_version does not contain correct versioning information.
Signed-off-by: Graham Sider <[email protected]>
Reviewed-by: Jack Xiao <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
This patch to fix the gdm3 start failure with virual display:
/usr/libexec/gdm-x-session[1711]: (II) AMDGPU(0): Setting screen physical size to 270 x 203
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): Failed to make import prime FD as pixmap: 22
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): failed to set mode: Invalid argument
/usr/libexec/gdm-x-session[1711]: (WW) AMDGPU(0): Failed to set mode on CRTC 0
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): Failed to enable any CRTC
gnome-shell[1840]: Running GNOME Shell (using mutter 42.2) as a X11 window and compositing manager
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): failed to set mode: Invalid argument
vkms doesn't have modifiers support, set fb_modifiers_not_supported to bring the gdm back.
Signed-off-by: Yifan Zhang <[email protected]>
Acked-by: Guchun Chen <[email protected]>
Reviewed-by: Tim Huang <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Missing send cursor_rect width & Height into DMUB. PSR-SU would use
these information. But missing these assignment in last refactor commit
Reported-by: Timur Kristóf <[email protected]>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2227
Fixes: b73353f7f3d4 ("drm/amd/display: Use the same cursor info across features")
Tested-by: Mark Broadworth <[email protected]>
Reviewed-by: Anthony Koo <[email protected]>
Acked-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Max Tseng <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Missed enabling timing sync on DCN32 because DCN32 has a different DML
param.
Tested-by: Mark Broadworth <[email protected]>
Reviewed-by: Martin Leung <[email protected]>
Reviewed-by: Jun Lei <[email protected]>
Acked-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Alvin Lee <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Arm SCMI fixes for v6.1
A bunch of fixes to handle:
1. A possible resource leak in scmi_remove(). The returned error
value gets ignored by the driver core and can remove the device and
free the devm-allocated resources. As a simple solution to be able to
easily backport, the bind attributes in the driver is suppressed as
there is no need to support it. Additionally the remove path is cleaned
up by adding device links between the core and the protocol devices
so that a proper and complete unbinding happens.
2. A possible spin-loop in the SCMI transmit path in case of misbehaving
platform firmware. A timeout is added to the existing loop so that
the SCMI stack can bailout aborting the transmission with warnings.
3. Optional Rx channel correctly by reporting any memory errors instead
of ignoring the same with other allowed errors.
4. The use of proper device for all the device managed allocations in the
virtio transport.
5. Incorrect deferred_tx_wq release on the error paths by using devres
API(devm_add_action_or_reset) to manage the release in the error path.
* tag 'scmi-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Fix deferred_tx_wq release on error paths
firmware: arm_scmi: Fix devres allocation device in virtio transport
firmware: arm_scmi: Make Rx chan_setup fail on memory errors
firmware: arm_scmi: Make tx_prepare time out eventually
firmware: arm_scmi: Suppress the driver's bind attributes
firmware: arm_scmi: Cleanup the core driver removal callback
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
[Why]
Cannot report 0 memclk levels even when SMU does not provide any.
[How]
When memclk levels reported by SMU is 0, set levels to 1.
Tested-by: Mark Broadworth <[email protected]>
Reviewed-by: Martin Leung <[email protected]>
Acked-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Dillon Varone <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected] # 6.0.x
|
|
Update DF related latencies based on new measurements.
Tested-by: Mark Broadworth <[email protected]>
Reviewed-by: Jun Lei <[email protected]>
Acked-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Dillon Varone <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected] # 6.0.x
|
|
[why]
Hardware team recommends we limit dispclock to 1950Mhz for all DCN3.2.x
[how]
Limit to 1950 when initializing clocks.
Tested-by: Mark Broadworth <[email protected]>
Reviewed-by: Alvin Lee <[email protected]>
Acked-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Jun Lei <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected] # 6.0.x
|
|
Ignore cable ID for DP2 receivers that does not support the feature.
Tested-by: Mark Broadworth <[email protected]>
Reviewed-by: Roman Li <[email protected]>
Acked-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Fangzhi Zuo <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
dcn314 has 4 DSC - conflicted hardware document updated and confirmed.
Tested-by: Mark Broadworth <[email protected]>
Reviewed-by: Charlene Liu <[email protected]>
Acked-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Leo Chen <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected] # 6.0.x
|