| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
To avoid the IO error, we need to cancel the delayed work and wait for it to finish.
Signed-off-by: Shuming Fan <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
snd_soc_update_bits returns a 1 when the bit was successfully updated,
returns a 0 is no update was needed and a negative if the call failed.
The code is currently failing the case of a successful update by just
checking for a non-zero number. Modify these checks and return the error
code only if there is a negative.
Fixes: 1a476abc723e6 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The devicetree binding indicates that the ti,asi-format, ti,imon-slot-no
and ti,vmon-slot-no are not required but the driver requires them or it
fails to probe. Honor the binding and allow these entries to be optional
and set the corresponding values to the default values for each as defined
in the data sheet.
Fixes: 1a476abc723e6 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add the BIAS_STANDBY and BIAS_PREPARE to the set_bias_level or else the
driver will return -EINVAL which is not correct as they are valid
states.
Fixes: 1a476abc723e6 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
tas2770_reset is called during i2c probe. The reset calls the
snd_soc_component_write which depends on the tas2770->component being
available. The component pointer is not set until codec_probe so move
the reset to the codec_probe after the pointer is set.
Fixes: 1a476abc723e6 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
To avoid the IO error, we need to cancel the delayed work and wait for it to finish.
Signed-off-by: Shuming Fan <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add the TAS2564 as a supported amplifier. This amplifier is register,
bitmap and feature compatible to the TAS2562.
Signed-off-by: Dan Murphy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add the TAS2564 compatible and data sheet link to the binding.
Signed-off-by: Dan Murphy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Fix build warning:
WARNING: modpost: missing MODULE_LICENSE() in sound/soc/sof/imx/imx-common.o
Fixes: 18ebffe4d043 ("ASoC: SOF: imx: Add debug support for imx platforms")
Reported-by: Stephen Rothwell <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Reviewed-by: Daniel Baluta <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
On i.MX platforms PM is not managed via ACPI although CONFIG_ACPI
can be set. So, in order to correctly set the system target state
we introduce a flag for platforms that require to use acpi target
states.
Signed-off-by: Daniel Baluta <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add volume controls for:
- Analog programmable gain amplifier (PGA) (-3 .. +12 dB)
- ADC attenuator (0 .. -96 dB)
Signed-off-by: Guillermo Rodríguez <[email protected]>
Acked-by: David Rhodes <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
In commit 783898ce68de ("ASoC: SOF: append extended data to
sof_ipc_comp_process") the process components are set to run on the
fixed core 0, this break us from scheduling components on any other DSP
core.
Since we can get the DSP core index from swidget->core, it is duplicated
to pass the extra 'core' argument for those sof_widget_load_xx()
functions.
Here removes the duplicate 'core' argument and get component core from
swidget->core directly to fix the issue mentioned above.
Fixes: 783898ce68de ("ASoC: SOF: append extended data to sof_ipc_comp_process")
Signed-off-by: Keyon Jie <[email protected]>
Reviewed-by: Jaska Uimonen <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add support to configure the GPIO pin to the specific configuration.
The GPIO pin can be configured as GPO, IRQ, SDOUT2, PDMCLK, MICBASE_EN,
GPI, MCLK, SDIN, PDMDIN1, PDMDIN2, PDMDIN3 or PDMDIN4 and the output
drive can be configured with various configuration.
Signed-off-by: Camel Guo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add properties for configuring the General Purpose Input Output (GPIO).
There are 2 settings for GPIO, configuration and the output drive type.
Signed-off-by: Camel Guo <[email protected]>
Acked-by: Dan Murphy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
<[email protected]>:
As sai ip is upgraded, so update sai register list.
Shengjiu Wang (3):
ASoC: fsl_sai: Add new added registers and new bit definition
ASoC: fsl_sai: Add fsl_sai_check_version function
ASoC: fsl_sai: Set MCLK input or output direction
changes in v2:
- update commit message for first commit
- Add acked-by Nicolin
sound/soc/fsl/fsl_sai.c | 77 ++++++++++++++++++++++++++++++++++++
sound/soc/fsl/fsl_sai.h | 87 +++++++++++++++++++++++++++++++++++++++++
2 files changed, 164 insertions(+)
--
2.27.0
|
|
<[email protected]>:
Series that adds debug support for IMX platforms, more details to
FW version information, adds missing -EACCESS handling to
pm_runtime_get_sync() calls and a set of minor cosmetic, trace
verbosity and coding style issues.
Guennadi Liakhovetski (3):
ASoC: SOF: (cosmetic) remove redundant "ret" variable uses
ASoC: SOF: remove several superfluous type-casts
ASoC: SOF: fix range checks
Iulian Olaru (1):
ASoC: SOF: imx: Add debug support for imx platforms
Karol Trzcinski (1):
ASoC: SOF: Add `src_hash` to `sof_ipc_fw_version` structure
Pierre-Louis Bossart (3):
ASoC: SOF: debug: update test for pm_runtime_get_sync()
ASoC: SOF: control: update test for pm_runtime_get_sync()
ASoC: SOF: Intel: hda: reduce verbosity of boot error logs
include/sound/sof/info.h | 4 +-
sound/soc/sof/control.c | 62 +++++++++++++--------------
sound/soc/sof/debug.c | 2 +-
sound/soc/sof/imx/Kconfig | 8 ++++
sound/soc/sof/imx/Makefile | 3 ++
sound/soc/sof/imx/imx-common.c | 72 ++++++++++++++++++++++++++++++++
sound/soc/sof/imx/imx-common.h | 16 +++++++
sound/soc/sof/imx/imx8.c | 23 +++++++++-
sound/soc/sof/imx/imx8m.c | 17 +++++++-
sound/soc/sof/intel/hda-loader.c | 16 +++----
sound/soc/sof/intel/hda.c | 12 ++++--
sound/soc/sof/intel/hda.h | 2 +
sound/soc/sof/sof-audio.c | 6 +--
sound/soc/sof/sof-priv.h | 8 ++++
sound/soc/sof/topology.c | 44 ++++++++++---------
15 files changed, 226 insertions(+), 69 deletions(-)
create mode 100644 sound/soc/sof/imx/imx-common.c
create mode 100644 sound/soc/sof/imx/imx-common.h
--
2.27.0
|
|
<[email protected]>:
q6afe already exposes clocks using apis, but not as proper
clock controller driver. This patch puts those clocks
in to a proper clock controller so that other drivers that
depend on those clocks can be properly expressed.
Srinivas Kandagatla (2):
ASoC: q6afe: dt-bindings: add q6afe clock bindings
ASoC: q6afe-clocks: add q6afe clock controller
.../devicetree/bindings/sound/qcom,q6afe.txt | 23 ++
include/dt-bindings/sound/qcom,q6afe.h | 74 ++++-
sound/soc/qcom/Kconfig | 4 +
sound/soc/qcom/qdsp6/Makefile | 1 +
sound/soc/qcom/qdsp6/q6afe-clocks.c | 270 ++++++++++++++++++
5 files changed, 371 insertions(+), 1 deletion(-)
create mode 100644 sound/soc/qcom/qdsp6/q6afe-clocks.c
--
2.21.0
|
|
Ak4458 can't support DSD512 format, but ak4497 can, so add
a new enum variable (enum ak4458_type) in ak4458_drvdata to
distinguish these two platforms.
Ak4497 has two kinds of DSD input pin, it can be selected by
the dsd-path property from DT.
In hw_params(), bit clock is calculated according to different
DSD format (DSD64, DSD128, DSD256, DSD512), then registers
are configured.
Signed-off-by: Shengjiu Wang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add "dsd-path" property, which is used for ak4497 codec
to select the DSD input pin.
Signed-off-by: Shengjiu Wang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add a property to indicate if the device is to go into a High-z state on
the Tx ASI output pins when the device is idle.
Signed-off-by: Dan Murphy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add code to allow the ASI Tx output to be placed into High-z mode
during unused ASI cycles. This allows for other devices that may be on
the bus to drive the ASI out. By default the 320adcx140 sends 0's for
unused cycles.
Signed-off-by: Dan Murphy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The lpass-sc7180 driver can be built as a module but is lacking a
MODULE_DEVICE_TABLE. This means it won't auto-load. Fix this
oversight.
Fixes: 24caf8d9eb10 ("ASoC: qcom: lpass-sc7180: Add platform driver for lpass audio")
Signed-off-by: Douglas Anderson <[email protected]>
Link: https://lore.kernel.org/r/20200916111545.1.I4c3758817d94c433bafeac344a395e21ea6657e3@changeid
Signed-off-by: Mark Brown <[email protected]>
|
|
SOF will support tgl-h and tgl-lp in different FW binaries due to
hardware difference, so create another dev_desc entry with FW name
of sof-tgl-h.ri and dsp_desc named tglh_chip_info for tgl-h.
Fixes: c8d2e2bfaeffa ("ASoC: SOF: Intel: add PCI IDs for ICL-H and TGL-H")
Signed-off-by: Rander Wang <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
To avoid the actual PLL settings to differ from the state expected by
the clock driver, the codec should only be fully reset before the clocks
are registered. But we also need to ensure that the software reset
happens at all before clock registration, as not all boards have a reset
GPIO.
Move the software reset from aic32x4_component_probe() to
aic32x4_probe() and reorder the reset and registration sequence:
1. Reset via GPIO (if available)
2. Reset via software
3. Register component
4. Register clocks
Note that aic32x4_component_probe() is only called after aic32x4_probe()
has finished, so the reset in aic32x4_component_probe() was happening too
late.
Signed-off-by: Matthias Schiffer <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
error path
The regulators need to be disabled in the aic32x4_register_clocks()
failure case as well.
Fixes: 9d4befff5a95 ("ASoC: codec: tlv3204: Moving GPIO reset and add ADC reset")
Signed-off-by: Matthias Schiffer <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted some
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The common pattern for enumerating compatibles is enum, not oneOf.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
|
|
SAI support select MCLK direction with version.major > 3
and version.minor > 1, the default direction is input,
set it to be output according to DT property.
Signed-off-by: Shengjiu Wang <[email protected]>
Acked-by: Nicolin Chen <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
fsl_sai_check_version can help to parse the version info
in VERID and PARAM registers.
Signed-off-by: Shengjiu Wang <[email protected]>
Acked-by: Nicolin Chen <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
On i.MX8MQ/i.MX8MN/i.MX8MM platform, the sai IP is upgraded.
There are some new registers and new bit definition. This
patch is to complete the register list.
Signed-off-by: Shengjiu Wang <[email protected]>
Acked-by: Nicolin Chen <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
q6afe already exposes lpass clocks, however this was not presented
as proper clock controller driver. This patch basically adds clock
controller support for q6afe clocks.
This is useful for other drivers like lpass digital codec or lpass
lowpower island drivers to request or vote for these clocks.
Signed-off-by: Srinivas Kandagatla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
q6afe exposes various lpass clocks controls via q6dsp q6afe commands.
This patch adds bindings required for this clock controller.
Signed-off-by: Srinivas Kandagatla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Previous commits reduced the verbosity of errors during boot
iterations, but there are still a couple remaining which generate
false positives. Errors should only be logged when after last attempt
to download firmware failed.
Duplicating logs and assigning them different levels based on the
iteration number isn't really elegant, use macro as suggested by
Guennadi.
Suggested-by: Guennadi Liakhovetski <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
On multiple locations checks are performed of untrusted values after adding
a constant to them. This is wrong, because the addition might overflow and
the result can then pass the check, although the original value is invalid.
Fix multiple such issues by checking the actual value and not a sum of it
and a constant.
Signed-off-by: Guennadi Liakhovetski <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
No need to type-cast assignments between void and other pointers in C.
Signed-off-by: Guennadi Liakhovetski <[email protected]>
Reviewed-by: Bard Liao <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
In some cases no "ret" variable is even needed, those functions always
return 0 anyway, in other cases "ret" initialisation is redundant.
Signed-off-by: Guennadi Liakhovetski <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
We need to avoid reporting an error for -EACCESS when pm_runtime is
not enabled.
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
We need to avoid reporting an error for -EACCESS when pm_runtime is
not enabled.
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This field will be used to compare ldc file with loaded fw version,
to assert validity of trace logs. Value used in sof-logger.
Signed-off-by: Karol Trzcinski <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This patch adds debug support for imx platforms. This is important in
order to gather information about the state of the DSP in case of an
oops and the reason for the oops.
This is done by checking if a message with a panic code has been placed
in the debug box, in the imx8_dsp_handle_request function from sof/imx.
If positive, the function imx8_dump, added in common, will be called.
The first step is to gather information about the registers, filename,
line number and stack by calling the imx8_get_registers, added in common.
Then the information will be printed to the console by calling the
get_status function.
Signed-off-by: Iulian Olaru <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Reviewed-by: Daniel Baluta <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Fix the BCLK inversion for DSP modes
This is how it is defined by ASoC:
* BCLK:
* - "normal" polarity means signal is available at rising edge of BCLK
* - "inverted" polarity means signal is available at falling edge of BCLK
The adcx140 defines the BCLK edge based on coding type.
The PCM (DSP_A/B) should drive on rising and sample on falling edge, so
from ASoC pov, it is IB_NF. But from the codec pov if it is configured in
DSP mode, then the BCLK should not be inverted, defaults to the coding
standard.
For i2s, it is NB_NF from ASoC pov (drive on falling, sample on rising).
>From the codec's pov BCLK should not invert either, as this is the default
for the coding.
So, inversion must take the format into account:
IB_NF + DSP_A/B == the codec bclk inversion should be disabled
NB_NF + DSP_A/B == the codec bclk inversion should be enabled
NB_NF + I2S == the codec bclk inversion should be disabled
Signed-off-by: Dan Murphy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
It was observed that if the device was active and register writes were
performed there were some unwanted behaviors particularly when writing
the word length and some filter options. So when writing to the device
the device should be placed in sleep mode and then exit sleep mode once
the register update is complete.
Signed-off-by: Dan Murphy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
According to its datasheet, the digital gain should be -100 dB when
CHx_DVOL is 1 and 27 dB when CHx_DVOL is 255. But with the current
dig_vol_tlv, "Digital CHx Out Volume" shows 27.5 dB if CHx_DVOL is 255
and -95.5 dB if CHx_DVOL is 1. This commit fixes this bug.
Fixes: 689c7655b50c ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Signed-off-by: Camel Guo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
When CONFIG_SND_CTL_VALIDATION is set, accesses to extended bytes
control generate spurious error messages when the size exceeds 512
bytes, such as
[ 11.224223] sof_sdw sof_sdw: control 2:0:0:EQIIR5.0 eqiir_coef_5:0:
invalid count 1024
In addition the error check returns -EINVAL which has the nasty side
effect of preventing applications accessing controls from working,
e.g.
root@plb:~# alsamixer
cannot load mixer controls: Invalid argument
It's agreed that the control interface has been abused since 2014, but
forcing a check should not prevent existing solutions from working.
This patch skips the checks conditionally if CONFIG_SND_CTL_VALIDATION
is set and the byte array provided by topology is > 512. This
preserves the checks for all other cases.
Fixes: 1a3232d2f61d2 ('ASoC: topology: Add support for TLV bytes controls')
BugLink: https://github.com/thesofproject/linux/issues/2430
Reported-by: Takashi Iwai <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Bard Liao <[email protected]>
Reviewed-by: Jaska Uimonen <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
"alsactl -f state.conf store/restore" sequence fails because setting
"mixing clock source" and "output source" requires active TDM clock
being started for configuration propagation. Make these two controls
write only so that their values are not stored at "alsactl store".
Signed-off-by: Viorel Suman <[email protected]>
Acked-by: Nicolin Chen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Fix the failure to flush DAC data before playback.
Signed-off-by: derek.fang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Fix the DC calibration unsuccessful issue on rt1015
bypass boost mode.
Signed-off-by: derek.fang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Vehmanen <[email protected]>:
This series contains some improvements to how DSP core management
is done in SOF, and adds a distinction between cores managed by
the host versus cores managed by the DSP.
Pierre-Louis Bossart (1):
ASoC: SOF: Intel: hda-loader: s/master/primary
Ranjani Sridharan (3):
ASoC: SOF: rename cores_mask to host_managed_cores_mask
ASoC: SOF: Intel: hda: modify core_power_up/down op
ASoC: SOF: Intel: remove the HDA_DSP_CORE_MASK() macro
sound/soc/sof/intel/apl.c | 2 +-
sound/soc/sof/intel/bdw.c | 2 +-
sound/soc/sof/intel/byt.c | 6 +++---
sound/soc/sof/intel/cnl.c | 15 ++++-----------
sound/soc/sof/intel/hda-dsp.c | 20 +++++++++++++++++---
sound/soc/sof/intel/hda-loader.c | 11 +++++------
sound/soc/sof/intel/hda.c | 2 +-
sound/soc/sof/intel/hda.h | 3 ---
sound/soc/sof/intel/shim.h | 2 +-
sound/soc/sof/intel/tgl.c | 2 +-
10 files changed, 34 insertions(+), 31 deletions(-)
--
2.27.0
|
|
rt1015p" from Tzung-Bi Shih <[email protected]>:
The series reuses mt8183-da7219-max98357.c for supporting machine
driver with rt1015p speaker amplifier.
The 1st patch adds document for the new proposed compatible string.
The 2nd patch changes the machine driver to support "RT1015P" codec.
Tzung-Bi Shih (2):
ASoC: dt-bindings: mt8183-da7219: add compatible string for using
rt1015p
ASoC: mediatek: mt8183-da7219: support machine driver with rt1015p
.../bindings/sound/mt8183-da7219-max98357.txt | 1 +
sound/soc/mediatek/Kconfig | 1 +
.../mediatek/mt8183/mt8183-da7219-max98357.c | 40 +++++++++++++++++++
3 files changed, 42 insertions(+)
--
2.28.0.526.ge36021eeef-goog
|