aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2018-05-10ceph: fix iov_iter issues in ceph_direct_read_write()Ilya Dryomov1-78/+117
dio_get_pagev_size() and dio_get_pages_alloc() introduced in commit b5b98989dc7e ("ceph: combine as many iovec as possile into one OSD request") assume that the passed iov_iter is ITER_IOVEC. This isn't the case with splice where it ends up poking into the guts of ITER_BVEC or ITER_PIPE iterators, causing lockups and crashes easily reproduced with generic/095. Rather than trying to figure out gap alignment and stuff pages into a page vector, add a helper for going from iov_iter to a bio_vec array and make use of the new CEPH_OSD_DATA_TYPE_BVECS code. Fixes: b5b98989dc7e ("ceph: combine as many iovec as possile into one OSD request") Link: http://tracker.ceph.com/issues/18130 Signed-off-by: Ilya Dryomov <[email protected]> Reviewed-by: Jeff Layton <[email protected]> Reviewed-by: "Yan, Zheng" <[email protected]> Tested-by: Luis Henriques <[email protected]>
2018-05-10libceph: add osd_req_op_extent_osd_data_bvecs()Ilya Dryomov3-7/+36
... and store num_bvecs for client code's convenience. Signed-off-by: Ilya Dryomov <[email protected]> Reviewed-by: Jeff Layton <[email protected]> Reviewed-by: "Yan, Zheng" <[email protected]>
2018-05-10ceph: fix rsize/wsize capping in ceph_direct_read_write()Ilya Dryomov1-5/+5
rsize/wsize cap should be applied before ceph_osdc_new_request() is called. Otherwise, if the size is limited by the cap instead of the stripe unit, ceph_osdc_new_request() would setup an extent op that is bigger than what dio_get_pages_alloc() would pin and add to the page vector, triggering asserts in the messenger. Cc: [email protected] Fixes: 95cca2b44e54 ("ceph: limit osd write size") Signed-off-by: Ilya Dryomov <[email protected]> Reviewed-by: "Yan, Zheng" <[email protected]>
2018-05-10mtd: rawnand: Make sure we wait tWB before polling the STATUS regBoris Brezillon1-0/+5
NAND chips require a bit of time to take the NAND operation into account and set the BUSY bit in the STATUS reg. Make sure we don't poll the STATUS reg too early in nand_soft_waitrdy(). Fixes: 8878b126df76 ("mtd: nand: add ->exec_op() implementation") Cc: <[email protected]> Signed-off-by: Boris Brezillon <[email protected]> Acked-by: Miquel Raynal <[email protected]>
2018-05-10Merge branch 'linux-4.17' of git://github.com/skeggsb/linux into drm-fixesDave Airlie4-10/+6
Two nouveau crasher/deadlock fixes. * 'linux-4.17' of git://github.com/skeggsb/linux: drm/nouveau: Fix deadlock in nv50_mstm_register_connector() drm/nouveau/ttm: don't dereference nvbo::cli, it can outlive client
2018-05-10drm/nouveau: Fix deadlock in nv50_mstm_register_connector()Lyude Paul1-4/+3
Currently; we're grabbing all of the modesetting locks before adding MST connectors to fbdev. This isn't actually necessary, and causes a deadlock as well: ====================================================== WARNING: possible circular locking dependency detected 4.17.0-rc3Lyude-Test+ #1 Tainted: G O ------------------------------------------------------ kworker/1:0/18 is trying to acquire lock: 00000000c832f62d (&helper->lock){+.+.}, at: drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] but task is already holding lock: 00000000942e28e2 (crtc_ww_class_mutex){+.+.}, at: drm_modeset_backoff+0x8e/0x1c0 [drm] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (crtc_ww_class_mutex){+.+.}: ww_mutex_lock+0x43/0x80 drm_modeset_lock+0x71/0x130 [drm] drm_helper_probe_single_connector_modes+0x7d/0x6b0 [drm_kms_helper] drm_setup_crtcs+0x15e/0xc90 [drm_kms_helper] __drm_fb_helper_initial_config_and_unlock+0x29/0x480 [drm_kms_helper] nouveau_fbcon_init+0x138/0x1a0 [nouveau] nouveau_drm_load+0x173/0x7e0 [nouveau] drm_dev_register+0x134/0x1c0 [drm] drm_get_pci_dev+0x8e/0x160 [drm] nouveau_drm_probe+0x1a9/0x230 [nouveau] pci_device_probe+0xcd/0x150 driver_probe_device+0x30b/0x480 __driver_attach+0xbc/0xe0 bus_for_each_dev+0x67/0x90 bus_add_driver+0x164/0x260 driver_register+0x57/0xc0 do_one_initcall+0x4d/0x323 do_init_module+0x5b/0x1f8 load_module+0x20e5/0x2ac0 __do_sys_finit_module+0xb7/0xd0 do_syscall_64+0x60/0x1b0 entry_SYSCALL_64_after_hwframe+0x49/0xbe -> #2 (crtc_ww_class_acquire){+.+.}: drm_helper_probe_single_connector_modes+0x58/0x6b0 [drm_kms_helper] drm_setup_crtcs+0x15e/0xc90 [drm_kms_helper] __drm_fb_helper_initial_config_and_unlock+0x29/0x480 [drm_kms_helper] nouveau_fbcon_init+0x138/0x1a0 [nouveau] nouveau_drm_load+0x173/0x7e0 [nouveau] drm_dev_register+0x134/0x1c0 [drm] drm_get_pci_dev+0x8e/0x160 [drm] nouveau_drm_probe+0x1a9/0x230 [nouveau] pci_device_probe+0xcd/0x150 driver_probe_device+0x30b/0x480 __driver_attach+0xbc/0xe0 bus_for_each_dev+0x67/0x90 bus_add_driver+0x164/0x260 driver_register+0x57/0xc0 do_one_initcall+0x4d/0x323 do_init_module+0x5b/0x1f8 load_module+0x20e5/0x2ac0 __do_sys_finit_module+0xb7/0xd0 do_syscall_64+0x60/0x1b0 entry_SYSCALL_64_after_hwframe+0x49/0xbe -> #1 (&dev->mode_config.mutex){+.+.}: drm_setup_crtcs+0x10c/0xc90 [drm_kms_helper] __drm_fb_helper_initial_config_and_unlock+0x29/0x480 [drm_kms_helper] nouveau_fbcon_init+0x138/0x1a0 [nouveau] nouveau_drm_load+0x173/0x7e0 [nouveau] drm_dev_register+0x134/0x1c0 [drm] drm_get_pci_dev+0x8e/0x160 [drm] nouveau_drm_probe+0x1a9/0x230 [nouveau] pci_device_probe+0xcd/0x150 driver_probe_device+0x30b/0x480 __driver_attach+0xbc/0xe0 bus_for_each_dev+0x67/0x90 bus_add_driver+0x164/0x260 driver_register+0x57/0xc0 do_one_initcall+0x4d/0x323 do_init_module+0x5b/0x1f8 load_module+0x20e5/0x2ac0 __do_sys_finit_module+0xb7/0xd0 do_syscall_64+0x60/0x1b0 entry_SYSCALL_64_after_hwframe+0x49/0xbe -> #0 (&helper->lock){+.+.}: __mutex_lock+0x70/0x9d0 drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] nv50_mstm_register_connector+0x2c/0x50 [nouveau] drm_dp_add_port+0x2f5/0x420 [drm_kms_helper] drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper] drm_dp_add_port+0x33f/0x420 [drm_kms_helper] drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper] drm_dp_check_and_send_link_address+0x87/0xd0 [drm_kms_helper] drm_dp_mst_link_probe_work+0x4d/0x80 [drm_kms_helper] process_one_work+0x20d/0x650 worker_thread+0x3a/0x390 kthread+0x11e/0x140 ret_from_fork+0x3a/0x50 other info that might help us debug this: Chain exists of: &helper->lock --> crtc_ww_class_acquire --> crtc_ww_class_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(crtc_ww_class_mutex); lock(crtc_ww_class_acquire); lock(crtc_ww_class_mutex); lock(&helper->lock); *** DEADLOCK *** 5 locks held by kworker/1:0/18: #0: 000000004a05cd50 ((wq_completion)"events_long"){+.+.}, at: process_one_work+0x187/0x650 #1: 00000000601c11d1 ((work_completion)(&mgr->work)){+.+.}, at: process_one_work+0x187/0x650 #2: 00000000586ca0df (&dev->mode_config.mutex){+.+.}, at: drm_modeset_lock_all+0x3a/0x1b0 [drm] #3: 00000000d3ca0ffa (crtc_ww_class_acquire){+.+.}, at: drm_modeset_lock_all+0x44/0x1b0 [drm] #4: 00000000942e28e2 (crtc_ww_class_mutex){+.+.}, at: drm_modeset_backoff+0x8e/0x1c0 [drm] stack backtrace: CPU: 1 PID: 18 Comm: kworker/1:0 Tainted: G O 4.17.0-rc3Lyude-Test+ #1 Hardware name: Gateway FX6840/FX6840, BIOS P01-A3 05/17/2010 Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper] Call Trace: dump_stack+0x85/0xcb print_circular_bug.isra.38+0x1ce/0x1db __lock_acquire+0x128f/0x1350 ? lock_acquire+0x9f/0x200 ? lock_acquire+0x9f/0x200 ? __ww_mutex_lock.constprop.13+0x8f/0x1000 lock_acquire+0x9f/0x200 ? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] ? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] __mutex_lock+0x70/0x9d0 ? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] ? ww_mutex_lock+0x43/0x80 ? _cond_resched+0x15/0x30 ? ww_mutex_lock+0x43/0x80 ? drm_modeset_lock+0xb2/0x130 [drm] ? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper] nv50_mstm_register_connector+0x2c/0x50 [nouveau] drm_dp_add_port+0x2f5/0x420 [drm_kms_helper] ? mark_held_locks+0x50/0x80 ? kfree+0xcf/0x2a0 ? drm_dp_check_mstb_guid+0xd6/0x120 [drm_kms_helper] ? trace_hardirqs_on_caller+0xed/0x180 ? drm_dp_check_mstb_guid+0xd6/0x120 [drm_kms_helper] drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper] drm_dp_add_port+0x33f/0x420 [drm_kms_helper] ? nouveau_connector_aux_xfer+0x7c/0xb0 [nouveau] ? find_held_lock+0x2d/0x90 ? drm_dp_dpcd_access+0xd9/0xf0 [drm_kms_helper] ? __mutex_unlock_slowpath+0x3b/0x280 ? drm_dp_dpcd_access+0xd9/0xf0 [drm_kms_helper] drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper] drm_dp_check_and_send_link_address+0x87/0xd0 [drm_kms_helper] drm_dp_mst_link_probe_work+0x4d/0x80 [drm_kms_helper] process_one_work+0x20d/0x650 worker_thread+0x3a/0x390 ? process_one_work+0x650/0x650 kthread+0x11e/0x140 ? kthread_create_worker_on_cpu+0x50/0x50 ret_from_fork+0x3a/0x50 Taking example from i915, the only time we need to hold any modesetting locks is when changing the port on the mstc, and in that case we only need to hold the connection mutex. Signed-off-by: Lyude Paul <[email protected]> Cc: Karol Herbst <[email protected]> Cc: [email protected] Signed-off-by: Lyude Paul <[email protected]> Signed-off-by: Ben Skeggs <[email protected]>
2018-05-10drm/nouveau/ttm: don't dereference nvbo::cli, it can outlive clientBen Skeggs3-6/+3
Potentially responsible for some random OOPSes. Signed-off-by: Ben Skeggs <[email protected]> Cc: [email protected] [v4.15+]
2018-05-10Merge branch 'drm-fixes-4.17' of git://people.freedesktop.org/~agd5f/linux ↵Dave Airlie13-95/+364
into drm-fixes A little bigger than normal since this is two weeks of fixes. - Atom firmware table updates for vega12 - Fix fallout from huge page support - Fix up smu7 power profile interface to be consistent with vega - Misc other fixes * 'drm-fixes-4.17' of git://people.freedesktop.org/~agd5f/linux: drm/amd/pp: Refine the output of pp_power_profile_mode on VI drm/amdgpu: Switch to interruptable wait to recover from ring hang. drm/ttm: Use GFP_TRANSHUGE_LIGHT for allocating huge pages drm/amd/display: Use kvzalloc for potentially large allocations drm/amd/display: Don't return ddc result and read_bytes in same return value drm/amd/display: Add get_firmware_info_v3_2 for VG12 drm/amd: Add BIOS smu_info v3_3 required struct def. drm/amd/display: Add VG12 ASIC IDs
2018-05-10Merge tag 'drm-misc-fixes-2018-05-09' of ↵Dave Airlie11-16/+69
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes atomic: Clear state pointers on clear (Ville) vc4: Fix oops in dpi disable (Eric) omap: Various error-checking + uninitialized var fixes (Tomi) Cc: Ville Syrjälä <[email protected]> Cc: Eric Anholt <[email protected]> Cc: Tomi Valkeinen <[email protected]> * tag 'drm-misc-fixes-2018-05-09' of git://anongit.freedesktop.org/drm/drm-misc: drm/vc4: Fix scaling of uni-planar formats drm/bridge/sii8620: add Kconfig dependency on extcon drm/omap: handle alloc failures in omap_connector drm/omap: add missing linefeeds to prints drm/omap: handle error if scale coefs are not found drm/omap: check return value from soc_device_match drm/omap: fix possible NULL ref issue in tiler_reserve_2d drm/omap: fix uninitialized ret variable drm/omap: silence unititialized variable warning drm/vc4: Fix oops dereferencing DPI's connector since panel_bridge. drm/atomic: Clean private obj old_state/new_state in drm_atomic_state_default_clear() drm/atomic: Clean old_state/new_state in drm_atomic_state_default_clear()
2018-05-10Merge tag 'drm-intel-fixes-2018-05-09' of ↵Dave Airlie4-25/+41
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes - Increase LVDS panel timeout to 5s to avoid spurious *ERROR* - Fix 2 WARNS: BIOS framebuffer related (FDO #105992) and eDP cdclk mismatch * tag 'drm-intel-fixes-2018-05-09' of git://anongit.freedesktop.org/drm/drm-intel: drm/i915: Fix drm:intel_enable_lvds ERROR message in kernel log drm/i915: Correctly populate user mode h/vdisplay with pipe src size during readout drm/i915: Adjust eDP's logical vco in a reliable place.
2018-05-10Merge tag 'exynos-drm-fixes-for-v4.17-rc5' of ↵Dave Airlie3-7/+18
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes Fixup pagefault issue of mixer driver - it makes sure to check shadow register for interlace scan. - it corrects chroma_addr[1], height and vertical position values. And trivial cleanup - it just removes duplicated drm_bridge_attach. * tag 'exynos-drm-fixes-for-v4.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos: drm/exynos: hdmi: avoid duplicating drm_bridge_attach drm/exynos: mixer: avoid Oops in vp_video_buffer() drm/exynos/mixer: fix synchronization check in interlaced mode
2018-05-10agp: uninorth: make two functions staticMathieu Malaterre1-2/+2
Both ‘uninorth_remove_memory’ and ‘null_cache_flush’ can be made static. So make them. Silence the following gcc warning (W=1): drivers/char/agp/uninorth-agp.c:198:5: warning: no previous prototype for ‘uninorth_remove_memory’ [-Wmissing-prototypes] and drivers/char/agp/uninorth-agp.c:473:6: warning: no previous prototype for ‘null_cache_flush’ [-Wmissing-prototypes] Signed-off-by: Mathieu Malaterre <[email protected]> Signed-off-by: Dave Airlie <[email protected]>
2018-05-09Merge branch 'for-linus' of ↵Linus Torvalds7-25/+71
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid Pull HID fixes from Jiri Kosina: - quirk for Toshiba Click Mini L9W-B, from Hans de Goede - intel-ish-hid and wacom error handling (device freeing) path fixes from Arvind Yadav - memory corruption fix in intel-ish-hid driver from Hans de Goede - a few new device ID additions to hid-lenovo from Peter Ganzhorn * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: i2c-hid: Add RESEND_REPORT_DESCR quirk for Toshiba Click Mini L9W-B HID: intel-ish-hid: use put_device() instead of kfree() HID: intel_ish-hid: Stop using a static local buffer in get_report() HID: intel_ish-hid: Move header size check to inside the loop HID: wacom: Release device resource data obtained by devres_alloc() HID: lenovo: Add support for IBM/Lenovo Scrollpoint mice
2018-05-09drm/amd/pp: Refine the output of pp_power_profile_mode on VIRex Zhu2-30/+23
In order to keep consist with Vega, the output format of the pp_power_profile_mode would be <integer><mode name string>< “*” for current profile>:"detail settings" and remove the "CURRENT" mode line. for example: NUM MODE_NAME SCLK_UP_HYST SCLK_DOWN_HYST SCLK_ACTIVE_LEVEL MCLK_UP_HYST MCLK_DOWN_HYST MCLK_ACTIVE_LEVEL 0 3D_FULL_SCREEN: 0 100 30 0 100 10 1 POWER_SAVING: 10 0 30 - - - 2 VIDEO: - - - 10 16 31 3 VR: 0 11 50 0 100 10 4 COMPUTE: 0 5 30 - - - 5 CUSTOM *: 0 5 30 0 100 10 NUM MODE_NAME SCLK_UP_HYST SCLK_DOWN_HYST SCLK_ACTIVE_LEVEL MCLK_UP_HYST MCLK_DOWN_HYST MCLK_ACTIVE_LEVEL 0 3D_FULL_SCREEN: 0 100 30 0 100 10 1 POWER_SAVING *: 10 0 30 0 100 10 2 VIDEO: - - - 10 16 31 3 VR: 0 11 50 0 100 10 4 COMPUTE: 0 5 30 - - - 5 CUSTOM: - - - - - - Reviewed-by: Evan Quan <[email protected]> Acked-by: Alex Deucher <[email protected]> Signed-off-by: Rex Zhu <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2018-05-09drm/amdgpu: Switch to interruptable wait to recover from ring hang.Andrey Grodzovsky1-2/+4
v2: Use dma_fence_wait instead of dma_fence_wait_timeout(...,MAX_SCHEDULE_TIMEOUT) Avoid printing error message for ERESTARTSYS Originally-by: David Panariti <[email protected]> Signed-off-by: Andrey Grodzovsky <[email protected]> Reviewed-by: Christian König <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2018-05-09drm/ttm: Use GFP_TRANSHUGE_LIGHT for allocating huge pagesMichel Dänzer2-4/+10
GFP_TRANSHUGE tries very hard to allocate huge pages, which can result in long delays with high memory pressure. I have observed firefox freezing for up to around a minute due to this while restic was taking a full system backup. Since we don't really need huge pages, use GFP_TRANSHUGE_LIGHT | __GFP_NORETRY instead, in order to fail quickly when there are no huge pages available. Set __GFP_KSWAPD_RECLAIM as well, in order for huge pages to be freed up in the background if necessary. With these changes, I'm no longer seeing freezes during a restic backup. Cc: [email protected] Reviewed-by: Christian König <[email protected]> Signed-off-by: Michel Dänzer <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2018-05-09drm/amd/display: Use kvzalloc for potentially large allocationsMichel Dänzer2-41/+45
Allocating up to 32 physically contiguous pages can easily fail (and has failed for me), and isn't necessary anyway. Reviewed-by: Harry Wentland <[email protected]> Signed-off-by: Michel Dänzer <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2018-05-09drm/amd/display: Don't return ddc result and read_bytes in same return valueHarry Wentland3-13/+22
The two ranges overlap. Signed-off-by: Harry Wentland <[email protected]> Acked-by: Alex Deucher <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2018-05-09drm/amd/display: Add get_firmware_info_v3_2 for VG12Harry Wentland1-1/+85
Signed-off-by: Harry Wentland <[email protected]> Acked-by: Alex Deucher <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2018-05-09drm/amd: Add BIOS smu_info v3_3 required struct def.Jerry (Fangzhi) Zuo1-2/+168
Signed-off-by: Jerry (Fangzhi) Zuo <[email protected]> Reviewed-by: Harry Wentland <[email protected]> Reviewed-by: Alex Deucher <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2018-05-09drm/amd/display: Add VG12 ASIC IDsHarry Wentland1-2/+7
Signed-off-by: Harry Wentland <[email protected]> Acked-by: Alex Deucher <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2018-05-09cifs: smb2ops: Fix listxattr() when there are no EAsPaulo Alcantara1-0/+6
As per listxattr(2): On success, a nonnegative number is returned indicating the size of the extended attribute name list. On failure, -1 is returned and errno is set appropriately. In SMB1, when the server returns an empty EA list through a listxattr(), it will correctly return 0 as there are no EAs for the given file. However, in SMB2+, it returns -ENODATA in listxattr() which is wrong since the request and response were sent successfully, although there's no actual EA for the given file. This patch fixes listxattr() for SMB2+ by returning 0 in cifs_listxattr() when the server returns an empty list of EAs. Signed-off-by: Paulo Alcantara <[email protected]> Reviewed-by: Aurelien Aptel <[email protected]> Signed-off-by: Steve French <[email protected]>
2018-05-09cifs: smbd: Enable signing with smbdirectLong Li2-13/+0
Now signing is supported with RDMA transport. Remove the code that disabled it. Signed-off-by: Long Li <[email protected]> Signed-off-by: Steve French <[email protected]> Reviewed-by: Ronnie Sahlberg <[email protected]>
2018-05-09cifs: Allocate validate negotiation request through kmallocLong Li1-30/+38
The data buffer allocated on the stack can't be DMA'ed, ib_dma_map_page will return an invalid DMA address for a buffer on stack. Even worse, this incorrect address can't be detected by ib_dma_mapping_error. Sending data from this address to hardware will not fail, but the remote peer will get junk data. Fix this by allocating the request on the heap in smb3_validate_negotiate. Changes in v2: Removed duplicated code on freeing buffers on function exit. (Thanks to Parav Pandit <[email protected]>) Fixed typo in the patch title. Changes in v3: Added "Fixes" to the patch. Changed several sizeof() to use *pointer in place of struct. Changes in v4: Added detailed comments on the failure through RDMA. Allocate request buffer using GPF_NOFS. Fixed possible memory leak. Changes in v5: Removed variable ret for checking return value. Changed to use pneg_inbuf->Dialects[0] to calculate unused space in pneg_inbuf. Fixes: ff1c038addc4 ("Check SMB3 dialects against downgrade attacks") Signed-off-by: Long Li <[email protected]> Signed-off-by: Steve French <[email protected]> Reviewed-by: Ronnie Sahlberg <[email protected]> Reviewed-by: Tom Talpey <[email protected]>
2018-05-09arm64: capabilities: Add NVIDIA Denver CPU to bp_harden listDavid Gilhooley1-0/+1
The NVIDIA Denver CPU also needs a PSCI call to harden the branch predictor. Signed-off-by: David Gilhooley <[email protected]> Signed-off-by: Will Deacon <[email protected]>
2018-05-09arm64: Add MIDR encoding for NVIDIA CPUsDavid Gilhooley1-0/+6
This patch adds the MIDR encodings for NVIDIA as well as the Denver and Carmel CPUs used in Tegra SoCs. Signed-off-by: David Gilhooley <[email protected]> Signed-off-by: Will Deacon <[email protected]>
2018-05-09HID: i2c-hid: Add RESEND_REPORT_DESCR quirk for Toshiba Click Mini L9W-BHans de Goede2-0/+3
The 0457:10fb touchscreen found on the Toshiba Click Mini L9W-B needs to have a report-decriptors command send to it on resume in order for the touchscreen to start generating events again on resume. Signed-off-by: Hans de Goede <[email protected]> Acked-by: Benjamin Tissoires <[email protected]> Signed-off-by: Jiri Kosina <[email protected]>
2018-05-09PCI / PM: Always check PME wakeup capability for runtime wakeup supportKai Heng Feng1-4/+4
USB controller ASM1042 stops working after commit de3ef1eb1cd0 (PM / core: Drop run_wake flag from struct dev_pm_info). The device in question is not power managed by platform firmware, furthermore, it only supports PME# from D3cold: Capabilities: [78] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot-,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Before commit de3ef1eb1cd0, the device never gets runtime suspended. After that commit, the device gets runtime suspended to D3hot, which can not generate any PME#. usb_hcd_pci_probe() unconditionally calls device_wakeup_enable(), hence device_can_wakeup() in pci_dev_run_wake() always returns true. So pci_dev_run_wake() needs to check PME wakeup capability as its first condition. In addition, change wakeup flag passed to pci_target_state() from false to true, because we want to find the deepest state different from D3cold that the device can still generate PME#. In this case, it's D0 for the device in question. Fixes: de3ef1eb1cd0 (PM / core: Drop run_wake flag from struct dev_pm_info) Signed-off-by: Kai-Heng Feng <[email protected]> Cc: 4.13+ <[email protected]> # 4.13+ Acked-by: Bjorn Helgaas <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2018-05-09cpufreq: schedutil: Avoid using invalid next_freqRafael J. Wysocki1-1/+2
If the next_freq field of struct sugov_policy is set to UINT_MAX, it shouldn't be used for updating the CPU frequency (this is a special "invalid" value), but after commit b7eaf1aab9f8 (cpufreq: schedutil: Avoid reducing frequency of busy CPUs prematurely) it may be passed as the new frequency to sugov_update_commit() in sugov_update_single(). Fix that by adding an extra check for the special UINT_MAX value of next_freq to sugov_update_single(). Fixes: b7eaf1aab9f8 (cpufreq: schedutil: Avoid reducing frequency of busy CPUs prematurely) Reported-by: Viresh Kumar <[email protected]> Cc: 4.12+ <[email protected]> # 4.12+ Signed-off-by: Rafael J. Wysocki <[email protected]> Acked-by: Viresh Kumar <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2018-05-09cpufreq: schedutil: remove stale commentJuri Lelli1-13/+0
After commit 794a56ebd9a57 (sched/cpufreq: Change the worker kthread to SCHED_DEADLINE) schedutil kthreads are "ignored" for a clock frequency selection point of view, so the potential corner case for RT tasks is not possible at all now. Remove the stale comment mentioning it. Signed-off-by: Juri Lelli <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2018-05-09PM: docs: intel_pstate: fix Active Mode w/o HWP paragraphJuri Lelli1-1/+1
P-state selection algorithm (powersave or performance) is selected by echoing the desired choice to scaling_governor sysfs attribute and not to scaling_cur_freq (as currently stated). Fix it. Signed-off-by: Juri Lelli <[email protected]> Reviewed-by: Srinivas Pandruvada <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2018-05-09PM: docs: sleep-states: Fix a typo ("includig")Jonathan Neuschäfer1-1/+1
Fix a typo in admin-guide/pm/sleep-states.rst. Signed-off-by: Jonathan Neuschäfer <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2018-05-09drm/vc4: Fix scaling of uni-planar formatsBoris Brezillon1-1/+1
When using uni-planar formats (like RGB), the scaling parameters are stored in plane 0, not plane 1. Fixes: fc04023fafec ("drm/vc4: Add support for YUV planes.") Cc: [email protected] Signed-off-by: Boris Brezillon <[email protected]> Reviewed-by: Eric Anholt <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2018-05-08r8169: fix powering up RTL8168hHeiner Kallweit1-0/+3
Since commit a92a08499b1f "r8169: improve runtime pm in general and suspend unused ports" interfaces w/o link are runtime-suspended after 10s. On systems where drivers take longer to load this can lead to the situation that the interface is runtime-suspended already when it's initially brought up. This shouldn't be a problem because rtl_open() resumes MAC/PHY. However with at least one chip version the interface doesn't properly come up, as reported here: https://bugzilla.kernel.org/show_bug.cgi?id=199549 The vendor driver uses a delay to give certain chip versions some time to resume before starting the PHY configuration. So let's do the same. I don't know which chip versions may be affected, therefore apply this delay always. This patch was reported to fix the issue for RTL8168h. I was able to reproduce the issue on an Asus H310I-Plus which also uses a RTL8168h. Also in my case the patch fixed the issue. Reported-by: Slava Kardakov <[email protected]> Tested-by: Slava Kardakov <[email protected]> Signed-off-by: Heiner Kallweit <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-05-09drm/exynos: hdmi: avoid duplicating drm_bridge_attachPeter Rosin1-2/+0
drm_bridge_attach takes care of these assignments, so there is no need to open-code them a second time. Signed-off-by: Peter Rosin <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2018-05-08Merge branch 'for-4.17-fixes' of ↵Linus Torvalds12-42/+95
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata fixes from Tejun Heo: "An earlier commit to add reset control for embedded ahci controllers affected some of the hardware specific drivers and got reverted for now. Other than that, just per-device workarounds and trivial changes" * 'for-4.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: driver core: add __printf verification to __ata_ehi_pushv_desc ata: fix spelling mistake: "directon" -> "direction" libata: Apply NOLPM quirk for SanDisk SD7UB3Q*G1001 SSDs libata: Apply NOLPM quirk for SAMSUNG MZMPC128HBFU-000MV SSD ata: ahci: mvebu: override ahci_stop_engine for mvebu AHCI libahci: Allow drivers to override stop_engine Revert "ata: ahci-platform: add reset control support"
2018-05-08Merge tag 'pinctrl-v4.17-2' of ↵Linus Torvalds3-8/+55
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control fixes from Linus Walleij: "Here are three pin control fixes. The Intel fixes are the most serious and important things I had queued since it affects a large portion of deployed Chromebooks. - Two major fixes for the Intel Cherryview and Sunrisepoint pin controllers, adjusting numberspaces so that they get aligned with various messed-up numbers encoded into the BIOS. - A fix for the Meson driver GPIO pin range" * tag 'pinctrl-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: sunrisepoint: Align GPIO number space with Windows pinctrl: cherryview: Associate IRQ descriptors to irqdomain pinctrl: meson-axg: fix the range of aobus bank
2018-05-08Merge tag 'gpio-v4.17-2' of ↵Linus Torvalds4-19/+20
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO fixes from Linus Walleij: "Sorry for lagging behind on sending the first batch of GPIO fixes for this cycle. Just too busy conferencing and the weather was too nice. Here it is anyway: some real important polishing on the error path facing userspace (tagged for stable as well) and some normal driver fixes. - Fix proper IRQ unmasking in the Aspeed driver. - Do not free unrequested descriptors on the errorpath when creating line handles from the userspace chardev requested GPIO lines. - Also fix the errorpath in the linehandle creation function. - Fix the get/set multiple GPIO lines for a few of the funky industrial GPIO cards on the ISA bus" * tag 'gpio-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: gpio: pcie-idio-24: Fix off-by-one error in get_multiple loop gpio: pcie-idio-24: Fix port memory offset for get_multiple/set_multiple callbacks gpio: pci-idio-16: Fix port memory offset for get_multiple callback gpio: fix error path in lineevent_create gpioib: do not free unrequested descriptors gpio: fix aspeed_gpio unmask irq
2018-05-08Merge tag 'linux-can-fixes-for-4.17-20180508' of ↵David S. Miller6-19/+23
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2018-05-08 this is a pull request for 7 patches for net/master. The first patch is by Jakob Unterwurzacher and increases the severity of bus-off messages in the generic CAN device infrastructure. The next two patches are by Uwe Kleine-König and fix the endianess detection in the flexcan driver. Jimmy Assarsson's patch for the kvaser driver corrects the stats counter for dropped tx-messages. Geert Uytterhoeven provides one patch and Sergei Shtylyov two patches for the rcan_canfd device tree binding description. ==================== Signed-off-by: David S. Miller <[email protected]>
2018-05-08Merge branch 'ieee802154-for-davem-2018-05-08' of ↵David S. Miller4-15/+20
git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan Stefan Schmidt says: ==================== pull-request: ieee802154 2018-05-08 An update from ieee802154 for your *net* tree. Two fixes for the mcr20a driver, which was being added in the 4.17 merge window, by Gustavo and myself. The atusb driver got a change to GFP_KERNEL where no GFP_ATOMIC is needed by Jia-Ju. The last and most important fix is from Alex to get IPv6 reassembly working again for the ieee802154 6lowpan adaptation. This got broken in 4.16 so please queue this one also up for the 4.16 stable tree. ==================== Signed-off-by: David S. Miller <[email protected]>
2018-05-08drm/i915: Fix drm:intel_enable_lvds ERROR message in kernel logFlorent Flament1-1/+2
Fix `[drm:intel_enable_lvds] *ERROR* timed out waiting for panel to power on` in kernel log at boot time. Toshiba Satellite Z930 laptops needs between 1 and 2 seconds to power on its screen during Intel i915 DRM initialization. This currently results in a `[drm:intel_enable_lvds] *ERROR* timed out waiting for panel to power on` message appearing in the kernel log during boot time and when stopping the machine. This change increases the timeout of the `intel_enable_lvds` function from 1 to 5 seconds, letting enough time for the Satellite 930 LCD screen to power on, and suppressing the error message from the kernel log. This patch has been successfully tested on Linux 4.14 running on a Toshiba Satellite Z930. [vsyrjala: bump the timeout from 2 to 5 seconds to match the DP code and properly cover the max hw timeout of ~4 seconds, and drop the comment about the specific machine since this is not a particulary surprising issue, nor specific to that one machine] Signed-off-by: Florent Flament <[email protected]> Cc: [email protected] Cc: Pavel Petrovic <[email protected]> Cc: Sérgio M. Basto <[email protected]> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103414 References: https://bugzilla.kernel.org/show_bug.cgi?id=57591 Signed-off-by: Ville Syrjälä <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Reviewed-by: Jani Nikula <[email protected]> (cherry picked from commit 280b54ade5914d3b4abe4f0ebe083ddbd4603246) Signed-off-by: Joonas Lahtinen <[email protected]>
2018-05-08drm/i915: Correctly populate user mode h/vdisplay with pipe src size during ↵Ville Syrjälä1-0/+2
readout During state readout we first read out the pipe src size, store that information in the user mode h/vdisplay, but later on we overwrite that with the actual crtc timings. That makes our read out crtc state inconsistent with itself when the BIOS has enabled the panel fitter to scale the pipe contents. Let's preserve the pipe src size based information in the user mode to make things consistent again. This fixes a problem introduced by commit a2936e3d9a9c ("drm/i915: Use drm_mode_get_hv_timing() to populate plane clip rectangle") where the inconsistent state is now leading the plane clipping code to report a failure on account the plane dst coordinates not matching the user mode size. Previously we did the plane clipping based on the pipe src size instead and thus never noticed the inconsistency. The failure manifests as a WARN: [ 0.762117] [drm:intel_dump_pipe_config [i915]] requested mode: [ 0.762142] [drm:drm_mode_debug_printmodeline [drm]] Modeline 0:"1366x768" 60 72143 1366 1414 1446 1526 768 771 777 784 0x40 0xa ... [ 0.762327] [drm:intel_dump_pipe_config [i915]] port clock: 72143, pipe src size: 1024x768, pixel rate 72143 ... [ 0.764666] [drm:drm_atomic_helper_check_plane_state [drm_kms_helper]] Plane must cover entire CRTC [ 0.764690] [drm:drm_rect_debug_print [drm]] dst: 1024x768+0+0 [ 0.764711] [drm:drm_rect_debug_print [drm]] clip: 1366x768+0+0 [ 0.764713] ------------[ cut here ]------------ [ 0.764714] Could not determine valid watermarks for inherited state [ 0.764792] WARNING: CPU: 4 PID: 159 at drivers/gpu/drm/i915/intel_display.c:14584 intel_modeset_init+0x3ce/0x19d0 [i915] ... Cc: FadeMind <[email protected]> Cc: Dave Jones <[email protected]> Cc: Daniel Vetter <[email protected]> Reported-by: FadeMind <[email protected]> Reported-by: Dave Jones <[email protected]> Tested-by: Dave Jones <[email protected]> References: https://lists.freedesktop.org/archives/intel-gfx/2018-April/163186.html Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105992 Fixes: a2936e3d9a9c ("drm/i915: Use drm_mode_get_hv_timing() to populate plane clip rectangle") Signed-off-by: Ville Syrjälä <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Reviewed-by: Chris Wilson <[email protected]> Tested-by: Larry Finger <[email protected]> Tested-by: FadeMind <[email protected]> (cherry picked from commit bd4cd03c81010dcd4e6f0e02e4c15f44aefe12d1) Signed-off-by: Joonas Lahtinen <[email protected]>
2018-05-08drm/i915: Adjust eDP's logical vco in a reliable place.Rodrigo Vivi2-24/+37
On intel_dp_compute_config() we were calculating the needed vco for eDP on gen9 and we stashing it in intel_atomic_state.cdclk.logical.vco However few moments later on intel_modeset_checks() we fully replace entire intel_atomic_state.cdclk.logical with dev_priv->cdclk.logical fully overwriting the logical desired vco for eDP on gen9. So, with wrong VCO value we end up with wrong desired cdclk, but also it will raise a lot of WARNs: On gen9, when we read CDCLK_CTL to verify if we configured properly the desired frequency the CD Frequency Select bits [27:26] == 10b can mean 337.5 or 308.57 MHz depending on the VCO. So if we have wrong VCO value stashed we will believe the frequency selection didn't stick and start to raise WARNs of cdclk mismatch. [ 42.857519] [drm:intel_dump_cdclk_state [i915]] Changing CDCLK to 308571 kHz, VCO 8640000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0 [ 42.897269] cdclk state doesn't match! [ 42.901052] WARNING: CPU: 5 PID: 1116 at drivers/gpu/drm/i915/intel_cdclk.c:2084 intel_set_cdclk+0x5d/0x110 [i915] [ 42.938004] RIP: 0010:intel_set_cdclk+0x5d/0x110 [i915] [ 43.155253] WARNING: CPU: 5 PID: 1116 at drivers/gpu/drm/i915/intel_cdclk.c:2084 intel_set_cdclk+0x5d/0x110 [i915] [ 43.170277] [drm:intel_dump_cdclk_state [i915]] [hw state] 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0 [ 43.182566] [drm:intel_dump_cdclk_state [i915]] [sw state] 308571 kHz, VCO 8640000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0 v2: Move the entire eDP's vco logical adjustment to inside the skl_modeset_calc_cdclk as suggested by Ville. Cc: Ville Syrjälä <[email protected]> Signed-off-by: Rodrigo Vivi <[email protected]> Reviewed-by: Ville Syrjälä <[email protected]> Fixes: bb0f4aab0e76 ("drm/i915: Track full cdclk state for the logical and actual cdclk frequencies") Cc: <[email protected]> # v4.12+ Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit 3297234a05ab1e90091b0574db4c397ef0e90d5f) Signed-off-by: Joonas Lahtinen <[email protected]>
2018-05-08DT: net: can: rcar_canfd: document R8A77980 bindingsSergei Shtylyov1-0/+1
Document the R-Car V3H (R8A77980) SoC support in the R-Car CAN-FD bindings. Signed-off-by: Sergei Shtylyov <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2018-05-08DT: net: can: rcar_canfd: document R8A77970 bindingsSergei Shtylyov1-0/+1
Document the R-Car V3M (R8A77970) SoC support in the R-Car CAN-FD bindings. Signed-off-by: Sergei Shtylyov <[email protected]> Reviewed-by: Ramesh Shanmugasundaram <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2018-05-08dt-bindings: can: rcar_can: Fix R8A7796 SoC nameGeert Uytterhoeven1-1/+1
R8A7796 is R-Car M3-W. Signed-off-by: Geert Uytterhoeven <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2018-05-08can: kvaser_usb: Increase correct stats counter in kvaser_usb_rx_can_msg()Jimmy Assarsson1-1/+1
Increase rx_dropped, if alloc_can_skb() fails, not tx_dropped. Signed-off-by: Jimmy Assarsson <[email protected]> Cc: linux-stable <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2018-05-08arm: dts: imx[35]*: declare flexcan devices to be compatible to imx25's flexcanUwe Kleine-König2-4/+4
Commit d50f4630c2e1 ("arm: dts: Remove p1010-flexcan compatible from imx series dts") removed the fallback compatible "fsl,p1010-flexcan" from the imx device trees. As the flexcan cores on i.MX25, i.MX35 and i.MX53 are identical, introduce the first as fallback for the two latter ones. Fixes: d50f4630c2e1 ("arm: dts: Remove p1010-flexcan compatible from imx series dts") Signed-off-by: Uwe Kleine-König <[email protected]> Cc: linux-stable <[email protected]> # >= v4.16 Signed-off-by: Marc Kleine-Budde <[email protected]>
2018-05-08can: flexcan: fix endianess detectionUwe Kleine-König1-12/+14
In commit 88462d2a7830 ("can: flexcan: Remodel FlexCAN register r/w APIs for big endian FlexCAN controllers.") the following logic was implemented: if the dt property "big-endian" is given or the device is compatible to "fsl,p1010-flexcan": use big-endian mode; else use little-endian mode; This relies on commit d50f4630c2e1 ("arm: dts: Remove p1010-flexcan compatible from imx series dts") which was applied a few commits later. Without this commit (or an old device tree used for booting a new kernel) the flexcan devices on i.MX25, i.MX28, i.MX35 and i.MX53 match the 'the device is compatible to "fsl,p1010-flexcan"' test and so are switched erroneously to big endian mode. Instead of the check above put a quirk in devtype data and rely on of_match_device yielding the most compatible match Fixes: 88462d2a7830 ("can: flexcan: Remodel FlexCAN register r/w APIs for big endian FlexCAN controllers.") Signed-off-by: Uwe Kleine-König <[email protected]> Tested-by: Gavin Schenk <[email protected]> Cc: linux-stable <[email protected]> # >= v4.16 Signed-off-by: Marc Kleine-Budde <[email protected]>
2018-05-08can: dev: increase bus-off message severityJakob Unterwurzacher1-1/+1
bus-off is usually caused by hardware malfunction or configuration error (baud rate mismatch) and causes a complete loss of communication. Increase the "bus-off" message's severity from netdev_dbg() to netdev_info() to make it visible to the user. A can interface going into bus-off is similar in severity to ethernet's "Link is Down" message, which is also printed at info level. It is debatable whether the the "restarted" message should also be changed to netdev_info() to make the interface state changes comprehensible from the kernel log. I have chosen to keep the "restarted" message at dbg for now as the "bus-off" message should be enough for the user to notice and investigate the problem. Signed-off-by: Jakob Unterwurzacher <[email protected]> Cc: [email protected] Cc: [email protected] Signed-off-by: Marc Kleine-Budde <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.