| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
destroy() will decrement the refcount on the interface, so that
it needs to be taken so early that it never undercounts.
Fixes: 7fb57a019f94e ("USB: cdc-acm: Fix potential deadlock (lockdep warning)")
Cc: stable <[email protected]>
Reported-and-tested-by: [email protected]
Signed-off-by: Oliver Neukum <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add a VID:PID for the BroadMobi BM818 M.2 card
T: Bus=01 Lev=03 Prnt=40 Port=03 Cnt=01 Dev#= 44 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2020 ProdID=2060 Rev=00.00
S: Manufacturer=Qualcomm, Incorporated
S: Product=Qualcomm CDMA Technologies MSM
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
Signed-off-by: Bob Ham <[email protected]>
Signed-off-by: Angus Ainslie (Purism) <[email protected]>
Cc: stable <[email protected]>
[ johan: use USB_DEVICE_INTERFACE_CLASS() ]
Signed-off-by: Johan Hovold <[email protected]>
|
|
On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams <[email protected]>.
As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold <[email protected]>.
The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork <[email protected]>.
However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.
The ttyUSB ports on Droid 4 are:
ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable
The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.
To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.
The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.
The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.
The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.
Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.
I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.
After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=2a70 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
In 22b8:900e "qc_dload" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=900e Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
And in 22b8:4281 "ram_downloader" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=4281 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Cc: Bjørn Mork <[email protected]>
Cc: Dan Williams <[email protected]>
Cc: Lars Melin <[email protected]>
Cc: Marcel Partap <[email protected]>
Cc: Merlijn Wajer <[email protected]>
Cc: Michael Scott <[email protected]>
Cc: NeKit <[email protected]>
Cc: Pavel Machek <[email protected]>
Cc: Sebastian Reichel <[email protected]>
Tested-by: Pavel Machek <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
There are a few different subsystems in the kernel that depend on model
specific behaviour (perf, EDAC, power, ...). Easier for just one person
to have the task to get new model numbers included instead of having
these groups trip over each other to do it.
[ bp: s/Cpu/CPU/ and add [email protected] so that it gets CCed too as
FYI. ]
Signed-off-by: Tony Luck <[email protected]>
Signed-off-by: Borislav Petkov <[email protected]>
Acked-by: Thomas Gleixner <[email protected]>
Cc: Dave Hansen <[email protected]>
Cc: x86-ml <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
drm-fixes-5.3-2019-08-14:
amdgpu:
- Use kvalloc for dc_state to avoid allocation
failures in some cases.
- Fix gfx9 soft recovery
scheduler:
- Fix a race condition when destroying entities
Signed-off-by: Dave Airlie <[email protected]>
From: Alex Deucher <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
I -thought- I had fixed this entirely, but it looks like that I didn't
test this thoroughly enough as we apparently still make one big mistake
with nv50_msto_atomic_check() - we don't handle the following scenario:
* CRTC #1 has n VCPI allocated to it, is attached to connector DP-4
which is attached to encoder #1. enabled=y active=n
* CRTC #1 is changed from DP-4 to DP-5, causing:
* DP-4 crtc=#1→NULL (VCPI n→0)
* DP-5 crtc=NULL→#1
* CRTC #1 steals encoder #1 back from DP-4 and gives it to DP-5
* CRTC #1 maintains the same mode as before, just with a different
connector
* mode_changed=n connectors_changed=y
(we _SHOULD_ do VCPI 0→n here, but don't)
Once the above scenario is repeated once, we'll attempt freeing VCPI
from the connector that we didn't allocate due to the connectors
changing, but the mode staying the same. Sigh.
Since nv50_msto_atomic_check() has broken a few times now, let's rethink
things a bit to be more careful: limit both VCPI/PBN allocations to
mode_changed || connectors_changed, since neither VCPI or PBN should
ever need to change outside of routing and mode changes.
Changes since v1:
* Fix accidental reversal of clock and bpp arguments in
drm_dp_calc_pbn_mode() - William Lewis
Signed-off-by: Lyude Paul <[email protected]>
Reported-by: Bohdan Milar <[email protected]>
Tested-by: Bohdan Milar <[email protected]>
Fixes: 232c9eec417a ("drm/nouveau: Use atomic VCPI helpers for MST")
References: 412e85b60531 ("drm/nouveau: Only release VCPI slots on mode changes")
Cc: Lyude Paul <[email protected]>
Cc: Ben Skeggs <[email protected]>
Cc: Daniel Vetter <[email protected]>
Cc: David Airlie <[email protected]>
Cc: Jerry Zuo <[email protected]>
Cc: Harry Wentland <[email protected]>
Cc: Juston Li <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Karol Herbst <[email protected]>
Cc: Ilia Mirkin <[email protected]>
Cc: <[email protected]> # v5.1+
Acked-by: Ben Skeggs <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
There is another thread still access standard VGA I/O while loading drm driver.
Disable standard VGA I/O decode to avoid this issue.
Signed-off-by: Y.C. Chen <[email protected]>
Reviewed-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
In blocked_fl_write(), 't' is not deallocated if bitmap_parse_user() fails,
leading to a memory leak bug. To fix this issue, free t before returning
the error.
Signed-off-by: Wenwen Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Diverged from what the code does with commit 530210c7814e ("of/irq: Replace
of_irq with of_phandle_args").
Signed-off-by: Lubomir Rintel <[email protected]>
Signed-off-by: Rob Herring <[email protected]>
|
|
The proper way to add additional contraints to an existing json-schema
is using 'allOf' to reference the base schema. Using just '$ref' doesn't
work. Fix this for the 'st,syscfg' property.
Cc: Mark Rutland <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Alexandre Torgue <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Rob Herring <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fallthrough fixes from Gustavo A. R. Silva:
"Fix sh mainline builds:
- Fix fall-through warning in sh.
- Fix missing break bug in sh (this is a 10-year-old bug)
Currently, mainline builds for sh are broken. These patches fix that"
* tag 'Wimplicit-fallthrough-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
sh: kernel: hw_breakpoint: Fix missing break in switch statement
sh: kernel: disassemble: Mark expected switch fall-throughs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull afs fixes from David Howells:
- Fix the CB.ProbeUuid handler to generate its reply correctly.
- Fix a mix up in indices when parsing a Volume Location entry record.
- Fix a potential NULL-pointer deref when cleaning up a read request.
- Fix the expected data version of the destination directory in
afs_rename().
- Fix afs_d_revalidate() to only update d_fsdata if it's not the same
as the directory data version to reduce the likelihood of overwriting
the result of a competing operation. (d_fsdata carries the directory
DV or the least-significant word thereof).
- Fix the tracking of the data-version on a directory and make sure
that dentry objects get properly initialised, updated and
revalidated.
Also fix rename to update d_fsdata to match the new directory's DV if
the dentry gets moved over and unhash the dentry to stop
afs_d_revalidate() from interfering.
* tag 'afs-fixes-20190814' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix missing dentry data version updating
afs: Only update d_fsdata if different in afs_d_revalidate()
afs: Fix off-by-one in afs_rename() expected data version calculation
fs: afs: Fix a possible null-pointer dereference in afs_put_read()
afs: Fix loop index mixup in afs_deliver_vl_get_entry_by_name_u()
afs: Fix the CB.ProbeUuid service handler to reply correctly
|
|
The spsc_queue_peek function is accessing queue->head which belongs to
the consumer thread and shouldn't be accessed by the producer
This is fixing a rare race condition when destroying entities.
Signed-off-by: Christian König <[email protected]>
Acked-by: Andrey Grodzovsky <[email protected]>
Reviewed-by: [email protected]
Signed-off-by: Alex Deucher <[email protected]>
|
|
Make the __fstate_clean() function correctly set the
state of sstatus.FS in pt_regs to SR_FS_CLEAN.
Fixes: 7db91e57a0acd ("RISC-V: Task implementation")
Cc: linux-stable <[email protected]>
Signed-off-by: Vincent Chen <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
[[email protected]: expanded "Fixes" commit ID]
Signed-off-by: Paul Walmsley <[email protected]>
|
|
The following two reasons cause FP registers are sometimes not
initialized before starting the user program.
1. Currently, the FP context is initialized in flush_thread() function
and we expect these initial values to be restored to FP register when
doing FP context switch. However, the FP context switch only occurs in
switch_to function. Hence, if this process does not be scheduled out
and scheduled in before entering the user space, the FP registers
have no chance to initialize.
2. In flush_thread(), the state of reg->sstatus.FS inherits from the
parent. Hence, the state of reg->sstatus.FS may be dirty. If this
process is scheduled out during flush_thread() and initializing the
FP register, the fstate_save() in switch_to will corrupt the FP context
which has been initialized until flush_thread().
To solve the 1st case, the initialization of the FP register will be
completed in start_thread(). It makes sure all FP registers are initialized
before starting the user program. For the 2nd case, the state of
reg->sstatus.FS in start_thread will be set to SR_FS_OFF to prevent this
process from corrupting FP context in doing context save. The FP state is
set to SR_FS_INITIAL in start_trhead().
Signed-off-by: Vincent Chen <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Fixes: 7db91e57a0acd ("RISC-V: Task implementation")
Cc: [email protected]
[[email protected]: fixed brace alignment issue reported by
checkpatch]
Signed-off-by: Paul Walmsley <[email protected]>
|
|
Pull rdma fixes from Doug Ledford:
"Fairly small pull request for -rc3. I'm out of town the rest of this
week, so I made sure to clean out as much as possible from patchworks
in enough time for 0-day to chew through it (Yay! for 0-day being back
online! :-)). Jason might send through any emergency stuff that could
pop up, otherwise I'm back next week.
The only real thing of note is the siw ABI change. Since we just
merged siw *this* release, there are no prior kernel releases to
maintain kernel ABI with. I told Bernard that if there is anything
else about the siw ABI he thinks he might want to change before it
goes set in stone, he should get it in ASAP. The siw module was around
for several years outside the kernel tree, and it had to be revamped
considerably for inclusion upstream, so we are making no attempts to
be backward compatible with the out of tree version. Once 5.3 is
actually released, we will have our baseline ABI to maintain.
Summary:
- Fix a memory registration release flow issue that was causing a
WARN_ON (mlx5)
- If the counters for a port aren't allocated, then we can't do
operations on the non-existent counters (core)
- Check the right variable for error code result (mlx5)
- Fix a use after free issue (mlx5)
- Fix an off by one memory leak (siw)
- Actually return an error code on error (core)
- Allow siw to be built on 32bit arches (siw, ABI change, but OK
since siw was just merged this merge window and there is no prior
released kernel to maintain compatibility with and we also updated
the rdma-core user space package to match)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/siw: Change CQ flags from 64->32 bits
RDMA/core: Fix error code in stat_get_doit_qp()
RDMA/siw: Fix a memory leak in siw_init_cpulist()
IB/mlx5: Fix use-after-free error while accessing ev_file pointer
IB/mlx5: Check the correct variable in error handling code
RDMA/counter: Prevent QP counter binding if counters unsupported
IB/mlx5: Fix implicit MR release flow
|
|
The `uac_mixer_unit_descriptor` shown as below is read from the
device side. In `parse_audio_mixer_unit`, `baSourceID` field is
accessed from index 0 to `bNrInPins` - 1, the current implementation
assumes that descriptor is always valid (the length of descriptor
is no shorter than 5 + `bNrInPins`). If a descriptor read from
the device side is invalid, it may trigger out-of-bound memory
access.
```
struct uac_mixer_unit_descriptor {
__u8 bLength;
__u8 bDescriptorType;
__u8 bDescriptorSubtype;
__u8 bUnitID;
__u8 bNrInPins;
__u8 baSourceID[];
}
```
This patch fixes the bug by add a sanity check on the length of
the descriptor.
Reported-by: Hui Peng <[email protected]>
Reported-by: Mathias Payer <[email protected]>
Cc: <[email protected]>
Signed-off-by: Hui Peng <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Pull dma-mapping fixes from Christoph Hellwig:
- fix the handling of the bus_dma_mask in dma_get_required_mask, which
caused a regression in this merge window (Lucas Stach)
- fix a regression in the handling of DMA_ATTR_NO_KERNEL_MAPPING (me)
- fix dma_mmap_coherent to not cause page attribute mismatches on
coherent architectures like x86 (me)
* tag 'dma-mapping-5.3-4' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: fix page attributes for dma_mmap_*
dma-direct: don't truncate dma_required_mask to bus addressing capabilities
dma-direct: fix DMA_ATTR_NO_KERNEL_MAPPING
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- A couple more fixes for the Intel VT-d driver for bugs introduced
during the recent conversion of this driver to use IOMMU core default
domains.
- Fix for common dma-iommu code to make sure MSI mappings happen in the
correct domain for a device.
- Fix a corner case in the handling of sg-lists in dma-iommu code that
might cause dma_length to be truncated.
- Mark a switch as fall-through in arm-smmu code.
* tag 'iommu-fixes-v5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix possible use-after-free of private domain
iommu/vt-d: Detach domain before using a private one
iommu/dma: Handle SG length overflow better
iommu/vt-d: Correctly check format of page table in debugfs
iommu/vt-d: Detach domain when move device out of group
iommu/arm-smmu: Mark expected switch fall-through
iommu/dma: Handle MSI mappings separately
|
|
Merge misc VM fixes from Andrew Morton:
"A bunch of hotfixes, all affecting mm/.
The two-patch series from Andrea may be controversial. This restores
patches which were reverted in Dec 2018 due to a regression report [*].
After extensive discussion it is evident that the problems which these
patches solved were significantly more serious than the problems they
introduced. I am told that major distros are already carrying these
two patches for this reason"
[*] See
https://lore.kernel.org/lkml/[email protected]/
https://lore.kernel.org/lkml/[email protected]/
for the google-specific issues brought up by David Rijentes. And as
Andrew says:
"I'm unaware of anyone else who will be adversely affected by this,
and google already carries over a thousand kernel patches - another
won't kill them.
There has been sporadic discussion about fixing these things for
real but it's clear that nobody apart from David is particularly
motivated"
* emailed patches from Andrew Morton <[email protected]>:
hugetlbfs: fix hugetlb page migration/fault race causing SIGBUS
mm, vmscan: do not special-case slab reclaim when watermarks are boosted
Revert "mm, thp: restore node-local hugepage allocations"
Revert "Revert "mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask""
include/asm-generic/5level-fixup.h: fix variable 'p4d' set but not used
seq_file: fix problem when seeking mid-record
mm: workingset: fix vmstat counters for shadow nodes
mm/usercopy: use memory range to be accessed for wraparound check
mm: kmemleak: disable early logging in case of error
mm/vmalloc.c: fix percpu free VM area search criteria
mm/memcontrol.c: fix use after free in mem_cgroup_iter()
mm/z3fold.c: fix z3fold_destroy_pool() race condition
mm/z3fold.c: fix z3fold_destroy_pool() ordering
mm: mempolicy: handle vma with unmovable pages mapped correctly in mbind
mm: mempolicy: make the behavior consistent when MPOL_MF_MOVE* and MPOL_MF_STRICT were specified
mm/hmm: fix bad subpage pointer in try_to_unmap_one
mm/hmm: fix ZONE_DEVICE anon page mapping reuse
mm: document zone device struct page field usage
|
|
Checking bypass_reg is incorrect for calculating the cnt_clk rates.
Instead we should be checking that there is a proper hardware register
that holds the clock divider.
Cc: [email protected]
Signed-off-by: Dinh Nguyen <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Stephen Boyd <[email protected]>
|
|
Don't fall through to print error message when receive sleep indication
in HCI_IBS_RX_ASLEEP state, this is allowed behavior.
Signed-off-by: Rocky Liao <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
This patch corrects the SPDX License Identifier style
in header file related to STM32 Driver for I2C hardware
bus support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
Suggested-by: Joe Perches <[email protected]>
Signed-off-by: Nishad Kamdar <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
|
|
After we disabled interrupts, there might still be an active one
running. Sync before clearing the pointer to the slave device.
Fixes: c31d0a00021d ("i2c: emev2: add slave support")
Reported-by: Krzysztof Adamski <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
Reviewed-by: Krzysztof Adamski <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
|
|
After we disabled interrupts, there might still be an active one
running. Sync before clearing the pointer to the slave device.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Reported-by: Krzysztof Adamski <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
Reviewed-by: Krzysztof Adamski <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
|
|
rxrpc_queue_local() attempts to queue the local endpoint it is given and
then, if successful, prints a trace line. The trace line includes the
current usage count - but we're not allowed to look at the local endpoint
at this point as we passed our ref on it to the workqueue.
Fix this by reading the usage count before queuing the work item.
Also fix the reading of local->debug_id for trace lines, which must be done
with the same consideration as reading the usage count.
Fixes: 09d2bf595db4 ("rxrpc: Add a tracepoint to track rxrpc_local refcounting")
Reported-by: [email protected]
Signed-off-by: David Howells <[email protected]>
|
|
When a local endpoint (struct rxrpc_local) ceases to be in use by any
AF_RXRPC sockets, it starts the process of being destroyed, but this
doesn't cause it to be removed from the namespace endpoint list immediately
as tearing it down isn't trivial and can't be done in softirq context, so
it gets deferred.
If a new socket comes along that wants to bind to the same endpoint, a new
rxrpc_local object will be allocated and rxrpc_lookup_local() will use
list_replace() to substitute the new one for the old.
Then, when the dying object gets to rxrpc_local_destroyer(), it is removed
unconditionally from whatever list it is on by calling list_del_init().
However, list_replace() doesn't reset the pointers in the replaced
list_head and so the list_del_init() will likely corrupt the local
endpoints list.
Fix this by using list_replace_init() instead.
Fixes: 730c5fd42c1e ("rxrpc: Fix local endpoint refcounting")
Reported-by: [email protected]
Signed-off-by: David Howells <[email protected]>
|
|
I would like to maintain the i2c-imx driver. Since I work with
different i.MX variants and have access to the hardware, I can spend
some time on the reviewing of this driver.
Signed-off-by: Oleksij Rempel <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
|
|
Since commit e1ab9a468e3b ("i2c: imx: improve the error handling in
i2c_imx_dma_request()") when booting with the DMA driver as module (such
as CONFIG_FSL_EDMA=m) the following endless clk warnings are seen:
[ 153.077831] ------------[ cut here ]------------
[ 153.082528] WARNING: CPU: 0 PID: 15 at drivers/clk/clk.c:924 clk_core_disable_lock+0x18/0x24
[ 153.093077] i2c0 already disabled
[ 153.096416] Modules linked in:
[ 153.099521] CPU: 0 PID: 15 Comm: kworker/0:1 Tainted: G W 5.2.0+ #321
[ 153.107290] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
[ 153.113772] Workqueue: events deferred_probe_work_func
[ 153.118979] [<c0019560>] (unwind_backtrace) from [<c0014734>] (show_stack+0x10/0x14)
[ 153.126778] [<c0014734>] (show_stack) from [<c083f8dc>] (dump_stack+0x9c/0xd4)
[ 153.134051] [<c083f8dc>] (dump_stack) from [<c0031154>] (__warn+0xf8/0x124)
[ 153.141056] [<c0031154>] (__warn) from [<c0031248>] (warn_slowpath_fmt+0x38/0x48)
[ 153.148580] [<c0031248>] (warn_slowpath_fmt) from [<c040fde0>] (clk_core_disable_lock+0x18/0x24)
[ 153.157413] [<c040fde0>] (clk_core_disable_lock) from [<c058f520>] (i2c_imx_probe+0x554/0x6ec)
[ 153.166076] [<c058f520>] (i2c_imx_probe) from [<c04b9178>] (platform_drv_probe+0x48/0x98)
[ 153.174297] [<c04b9178>] (platform_drv_probe) from [<c04b7298>] (really_probe+0x1d8/0x2c0)
[ 153.182605] [<c04b7298>] (really_probe) from [<c04b7554>] (driver_probe_device+0x5c/0x174)
[ 153.190909] [<c04b7554>] (driver_probe_device) from [<c04b58c8>] (bus_for_each_drv+0x44/0x8c)
[ 153.199480] [<c04b58c8>] (bus_for_each_drv) from [<c04b746c>] (__device_attach+0xa0/0x108)
[ 153.207782] [<c04b746c>] (__device_attach) from [<c04b65a4>] (bus_probe_device+0x88/0x90)
[ 153.215999] [<c04b65a4>] (bus_probe_device) from [<c04b6a04>] (deferred_probe_work_func+0x60/0x90)
[ 153.225003] [<c04b6a04>] (deferred_probe_work_func) from [<c004f190>] (process_one_work+0x204/0x634)
[ 153.234178] [<c004f190>] (process_one_work) from [<c004f618>] (worker_thread+0x20/0x484)
[ 153.242315] [<c004f618>] (worker_thread) from [<c0055c2c>] (kthread+0x118/0x150)
[ 153.249758] [<c0055c2c>] (kthread) from [<c00090b4>] (ret_from_fork+0x14/0x20)
[ 153.257006] Exception stack(0xdde43fb0 to 0xdde43ff8)
[ 153.262095] 3fa0: 00000000 00000000 00000000 00000000
[ 153.270306] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 153.278520] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 153.285159] irq event stamp: 3323022
[ 153.288787] hardirqs last enabled at (3323021): [<c0861c4c>] _raw_spin_unlock_irq+0x24/0x2c
[ 153.297261] hardirqs last disabled at (3323022): [<c040d7a0>] clk_enable_lock+0x10/0x124
[ 153.305392] softirqs last enabled at (3322092): [<c000a504>] __do_softirq+0x344/0x540
[ 153.313352] softirqs last disabled at (3322081): [<c00385c0>] irq_exit+0x10c/0x128
[ 153.320946] ---[ end trace a506731ccd9bd703 ]---
This endless clk warnings behaviour is well explained by Andrey Smirnov:
"Allocating DMA after registering I2C adapter can lead to infinite
probing loop, for example, consider the following scenario:
1. i2c_imx_probe() is called and successfully registers an I2C
adapter via i2c_add_numbered_adapter()
2. As a part of i2c_add_numbered_adapter() new I2C slave devices
are added from DT which results in a call to
driver_deferred_probe_trigger()
3. i2c_imx_probe() continues and calls i2c_imx_dma_request() which
due to lack of proper DMA driver returns -EPROBE_DEFER
4. i2c_imx_probe() fails, removes I2C adapter and returns
-EPROBE_DEFER, which places it into deferred probe list
5. Deferred probe work triggered in #2 above kicks in and calls
i2c_imx_probe() again thus bringing us to step #1"
So revert commit e1ab9a468e3b ("i2c: imx: improve the error handling in
i2c_imx_dma_request()") and restore the old behaviour, in order to
avoid regressions on existing setups.
Cc: <[email protected]>
Reported-by: Andrey Smirnov <[email protected]>
Reported-by: Russell King <[email protected]>
Fixes: e1ab9a468e3b ("i2c: imx: improve the error handling in i2c_imx_dma_request()")
Signed-off-by: Fabio Estevam <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
|
|
TCP rst and fin packets do not qualify to place a flow into the
flowtable. Most likely there will be no more packets after connection
closure. Without this patch, this flow entry expires and connection
tracking picks up the entry in ESTABLISHED state using the fixup
timeout, which makes this look inconsistent to the user for a connection
that is actually already closed.
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Make codec enter D3 before rebooting or poweroff can fix the noise
issue on some laptops. And in theory it is harmless for all codecs
to enter D3 before rebooting or poweroff, let us add a generic
reboot_notify, then realtek and conexant drivers can call this
function.
Cc: [email protected]
Signed-off-by: Hui Wang <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
We have 3 new lenovo laptops which have conexant codec 0x14f11f86,
these 3 laptops also have the noise issue when rebooting, after
letting the codec enter D3 before rebooting or poweroff, the noise
disappers.
Instead of adding a new ID again in the reboot_notify(), let us make
this function apply to all conexant codec. In theory make codec enter
D3 before rebooting or poweroff is harmless, and I tested this change
on a couple of other Lenovo laptops which have different conexant
codecs, there is no side effect so far.
Cc: [email protected]
Signed-off-by: Hui Wang <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
If the stream outq is not empty, need to kfree nstr_list.
Fixes: d570a59c5b5f ("sctp: only allow the out stream reset when the stream outq is empty")
Reported-by: Hulk Robot <[email protected]>
Signed-off-by: zhengbin <[email protected]>
Acked-by: Marcelo Ricardo Leitner <[email protected]>
Acked-by: Neil Horman <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Eric reported a syzbot warning:
BUG: KMSAN: uninit-value in nh_valid_get_del_req+0x6f1/0x8c0 net/ipv4/nexthop.c:1510
CPU: 0 PID: 11812 Comm: syz-executor444 Not tainted 5.3.0-rc3+ #17
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x162/0x2d0 mm/kmsan/kmsan_report.c:109
__msan_warning+0x75/0xe0 mm/kmsan/kmsan_instr.c:294
nh_valid_get_del_req+0x6f1/0x8c0 net/ipv4/nexthop.c:1510
rtm_del_nexthop+0x1b1/0x610 net/ipv4/nexthop.c:1543
rtnetlink_rcv_msg+0x115a/0x1580 net/core/rtnetlink.c:5223
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477
rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5241
netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
netlink_unicast+0xf6c/0x1050 net/netlink/af_netlink.c:1328
netlink_sendmsg+0x110f/0x1330 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg net/socket.c:657 [inline]
___sys_sendmsg+0x14ff/0x1590 net/socket.c:2311
__sys_sendmmsg+0x53a/0xae0 net/socket.c:2413
__do_sys_sendmmsg net/socket.c:2442 [inline]
__se_sys_sendmmsg+0xbd/0xe0 net/socket.c:2439
__x64_sys_sendmmsg+0x56/0x70 net/socket.c:2439
do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:297
entry_SYSCALL_64_after_hwframe+0x63/0xe7
The root cause is nlmsg_parse calling __nla_parse which means the
header struct size is not checked.
nlmsg_parse should be a wrapper around __nlmsg_parse with
NL_VALIDATE_STRICT for the validate argument very much like
nlmsg_parse_deprecated is for NL_VALIDATE_LIBERAL.
Fixes: 3de6440354465 ("netlink: re-add parse/validate functions in strict mode")
Reported-by: Eric Dumazet <[email protected]>
Reported-by: syzbot <[email protected]>
Signed-off-by: David Ahern <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
After configuring and restarting aneg we immediately try to read the
link status. On some systems the PHY may not yet have cleared the
"aneg complete" and "link up" bits, resulting in a false link-up
signal. See [0] for a report.
Clause 22 and 45 both require the PHY to keep the AN_RESTART
bit set until the PHY actually starts auto-negotiation.
Let's consider this in the generic functions for reading link status.
The commit marked as fixed is the first one where the patch applies
cleanly.
[0] https://marc.info/?t=156518400300003&r=1&w=2
Fixes: c1164bb1a631 ("net: phy: check PMAPMD link status only in genphy_c45_read_link")
Tested-by: Yonglong Liu <[email protected]>
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In mlx4_en_config_rss_steer(), 'rss_map->indir_qp' is allocated through
kzalloc(). After that, mlx4_qp_alloc() is invoked to configure RSS
indirection. However, if mlx4_qp_alloc() fails, the allocated
'rss_map->indir_qp' is not deallocated, leading to a memory leak bug.
To fix the above issue, add the 'qp_alloc_err' label to free
'rss_map->indir_qp'.
Fixes: 4931c6ef04b4 ("net/mlx4_en: Optimized single ring steering")
Signed-off-by: Wenwen Wang <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The ibm,mac-address-filters property defines the maximum number of
addresses the hypervisor's multicast filter list can support. It is
encoded as a big-endian integer in the OF device tree, but the virtual
ethernet driver does not convert it for use by little-endian systems.
As a result, the driver is not behaving as it should on affected systems
when a large number of multicast addresses are assigned to the device.
Reported-by: Hangbin Liu <[email protected]>
Signed-off-by: Thomas Falcon <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Callbacks for a cmd reply run outside the protection of card->lock, to
allow for additional cmds to be issued & enqueued in parallel.
When qeth_send_control_data() bails out for a cmd without having
received a reply (eg. due to timeout), its callback may concurrently be
processing a reply that just arrived. In this case, the callback
potentially accesses a stale reply->reply_param area that eg. was
on-stack and has already been released.
To avoid this race, add some locking so that qeth_send_control_data()
can (1) wait for a concurrently running callback, and (2) zap any
pending callback that still wants to run.
Signed-off-by: Julian Wiedmann <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Update the defconfig:
- Add CONFIG_HW_RANDOM=y and CONFIG_HW_RANDOM_VIRTIO=y to enable
VirtIORNG when running on QEMU
Signed-off-by: Alistair Francis <[email protected]>
Signed-off-by: Paul Walmsley <[email protected]>
|
|
Update the rv32_defconfig:
- Add 'CONFIG_DEVTMPFS_MOUNT=y' to match the RISC-V defconfig
- Add CONFIG_HW_RANDOM=y and CONFIG_HW_RANDOM_VIRTIO=y to enable
VirtIORNG when running on QEMU
Signed-off-by: Alistair Francis <[email protected]>
Signed-off-by: Paul Walmsley <[email protected]>
|
|
As the annotation says in sctp_do_8_2_transport_strike():
"If the transport error count is greater than the pf_retrans
threshold, and less than pathmaxrtx ..."
It should be transport->error_count checked with pathmaxrxt,
instead of asoc->pf_retrans.
Fixes: 5aa93bcf66f4 ("sctp: Implement quick failover draft from tsvwg")
Signed-off-by: Xin Long <[email protected]>
Acked-by: Marcelo Ricardo Leitner <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Li Wang discovered that LTP/move_page12 V2 sometimes triggers SIGBUS in
the kernel-v5.2.3 testing. This is caused by a race between hugetlb
page migration and page fault.
If a hugetlb page can not be allocated to satisfy a page fault, the task
is sent SIGBUS. This is normal hugetlbfs behavior. A hugetlb fault
mutex exists to prevent two tasks from trying to instantiate the same
page. This protects against the situation where there is only one
hugetlb page, and both tasks would try to allocate. Without the mutex,
one would fail and SIGBUS even though the other fault would be
successful.
There is a similar race between hugetlb page migration and fault.
Migration code will allocate a page for the target of the migration. It
will then unmap the original page from all page tables. It does this
unmap by first clearing the pte and then writing a migration entry. The
page table lock is held for the duration of this clear and write
operation. However, the beginnings of the hugetlb page fault code
optimistically checks the pte without taking the page table lock. If
clear (as it can be during the migration unmap operation), a hugetlb
page allocation is attempted to satisfy the fault. Note that the page
which will eventually satisfy this fault was already allocated by the
migration code. However, the allocation within the fault path could
fail which would result in the task incorrectly being sent SIGBUS.
Ideally, we could take the hugetlb fault mutex in the migration code
when modifying the page tables. However, locks must be taken in the
order of hugetlb fault mutex, page lock, page table lock. This would
require significant rework of the migration code. Instead, the issue is
addressed in the hugetlb fault code. After failing to allocate a huge
page, take the page table lock and check for huge_pte_none before
returning an error. This is the same check that must be made further in
the code even if page allocation is successful.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 290408d4a250 ("hugetlb: hugepage migration core")
Signed-off-by: Mike Kravetz <[email protected]>
Reported-by: Li Wang <[email protected]>
Tested-by: Li Wang <[email protected]>
Reviewed-by: Naoya Horiguchi <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Cc: Cyril Hrubis <[email protected]>
Cc: Xishi Qiu <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Dave Chinner reported a problem pointing a finger at commit 1c30844d2dfe
("mm: reclaim small amounts of memory when an external fragmentation
event occurs").
The report is extensive:
https://lore.kernel.org/linux-mm/[email protected]/
and it's worth recording the most relevant parts (colorful language and
typos included).
When running a simple, steady state 4kB file creation test to
simulate extracting tarballs larger than memory full of small
files into the filesystem, I noticed that once memory fills up
the cache balance goes to hell.
The workload is creating one dirty cached inode for every dirty
page, both of which should require a single IO each to clean and
reclaim, and creation of inodes is throttled by the rate at which
dirty writeback runs at (via balance dirty pages). Hence the ingest
rate of new cached inodes and page cache pages is identical and
steady. As a result, memory reclaim should quickly find a steady
balance between page cache and inode caches.
The moment memory fills, the page cache is reclaimed at a much
faster rate than the inode cache, and evidence suggests that
the inode cache shrinker is not being called when large batches
of pages are being reclaimed. In roughly the same time period
that it takes to fill memory with 50% pages and 50% slab caches,
memory reclaim reduces the page cache down to just dirty pages
and slab caches fill the entirety of memory.
The LRU is largely full of dirty pages, and we're getting spikes
of random writeback from memory reclaim so it's all going to shit.
Behaviour never recovers, the page cache remains pinned at just
dirty pages, and nothing I could tune would make any difference.
vfs_cache_pressure makes no difference - I would set it so high
it should trim the entire inode caches in a single pass, yet it
didn't do anything. It was clear from tracing and live telemetry
that the shrinkers were pretty much not running except when
there was absolutely no memory free at all, and then they did
the minimum necessary to free memory to make progress.
So I went looking at the code, trying to find places where pages
got reclaimed and the shrinkers weren't called. There's only one
- kswapd doing boosted reclaim as per commit 1c30844d2dfe ("mm:
reclaim small amounts of memory when an external fragmentation
event occurs").
The watermark boosting introduced by the commit is triggered in response
to an allocation "fragmentation event". The boosting was not intended
to target THP specifically and triggers even if THP is disabled.
However, with Dave's perfectly reasonable workload, fragmentation events
can be very common given the ratio of slab to page cache allocations so
boosting remains active for long periods of time.
As high-order allocations might use compaction and compaction cannot
move slab pages the decision was made in the commit to special-case
kswapd when watermarks are boosted -- kswapd avoids reclaiming slab as
reclaiming slab does not directly help compaction.
As Dave notes, this decision means that slab can be artificially
protected for long periods of time and messes up the balance with slab
and page caches.
Removing the special casing can still indirectly help avoid
fragmentation by avoiding fragmentation-causing events due to slab
allocation as pages from a slab pageblock will have some slab objects
freed. Furthermore, with the special casing, reclaim behaviour is
unpredictable as kswapd sometimes examines slab and sometimes does not
in a manner that is tricky to tune or analyse.
This patch removes the special casing. The downside is that this is not
a universal performance win. Some benchmarks that depend on the
residency of data when rereading metadata may see a regression when slab
reclaim is restored to its original behaviour. Similarly, some
benchmarks that only read-once or write-once may perform better when
page reclaim is too aggressive. The primary upside is that slab
shrinker is less surprising (arguably more sane but that's a matter of
opinion), behaves consistently regardless of the fragmentation state of
the system and properly obeys VM sysctls.
A fsmark benchmark configuration was constructed similar to what Dave
reported and is codified by the mmtest configuration
config-io-fsmark-small-file-stream. It was evaluated on a 1-socket
machine to avoid dealing with NUMA-related issues and the timing of
reclaim. The storage was an SSD Samsung Evo and a fresh trimmed XFS
filesystem was used for the test data.
This is not an exact replication of Dave's setup. The configuration
scales its parameters depending on the memory size of the SUT to behave
similarly across machines. The parameters mean the first sample
reported by fs_mark is using 50% of RAM which will barely be throttled
and look like a big outlier. Dave used fake NUMA to have multiple
kswapd instances which I didn't replicate. Finally, the number of
iterations differ from Dave's test as the target disk was not large
enough. While not identical, it should be representative.
fsmark
5.3.0-rc3 5.3.0-rc3
vanilla shrinker-v1r1
Min 1-files/sec 4444.80 ( 0.00%) 4765.60 ( 7.22%)
1st-qrtle 1-files/sec 5005.10 ( 0.00%) 5091.70 ( 1.73%)
2nd-qrtle 1-files/sec 4917.80 ( 0.00%) 4855.60 ( -1.26%)
3rd-qrtle 1-files/sec 4667.40 ( 0.00%) 4831.20 ( 3.51%)
Max-1 1-files/sec 11421.50 ( 0.00%) 9999.30 ( -12.45%)
Max-5 1-files/sec 11421.50 ( 0.00%) 9999.30 ( -12.45%)
Max-10 1-files/sec 11421.50 ( 0.00%) 9999.30 ( -12.45%)
Max-90 1-files/sec 4649.60 ( 0.00%) 4780.70 ( 2.82%)
Max-95 1-files/sec 4491.00 ( 0.00%) 4768.20 ( 6.17%)
Max-99 1-files/sec 4491.00 ( 0.00%) 4768.20 ( 6.17%)
Max 1-files/sec 11421.50 ( 0.00%) 9999.30 ( -12.45%)
Hmean 1-files/sec 5004.75 ( 0.00%) 5075.96 ( 1.42%)
Stddev 1-files/sec 1778.70 ( 0.00%) 1369.66 ( 23.00%)
CoeffVar 1-files/sec 33.70 ( 0.00%) 26.05 ( 22.71%)
BHmean-99 1-files/sec 5053.72 ( 0.00%) 5101.52 ( 0.95%)
BHmean-95 1-files/sec 5053.72 ( 0.00%) 5101.52 ( 0.95%)
BHmean-90 1-files/sec 5107.05 ( 0.00%) 5131.41 ( 0.48%)
BHmean-75 1-files/sec 5208.45 ( 0.00%) 5206.68 ( -0.03%)
BHmean-50 1-files/sec 5405.53 ( 0.00%) 5381.62 ( -0.44%)
BHmean-25 1-files/sec 6179.75 ( 0.00%) 6095.14 ( -1.37%)
5.3.0-rc3 5.3.0-rc3
vanillashrinker-v1r1
Duration User 501.82 497.29
Duration System 4401.44 4424.08
Duration Elapsed 8124.76 8358.05
This is showing a slight skew for the max result representing a large
outlier for the 1st, 2nd and 3rd quartile are similar indicating that
the bulk of the results show little difference. Note that an earlier
version of the fsmark configuration showed a regression but that
included more samples taken while memory was still filling.
Note that the elapsed time is higher. Part of this is that the
configuration included time to delete all the test files when the test
completes -- the test automation handles the possibility of testing
fsmark with multiple thread counts. Without the patch, many of these
objects would be memory resident which is part of what the patch is
addressing.
There are other important observations that justify the patch.
1. With the vanilla kernel, the number of dirty pages in the system is
very low for much of the test. With this patch, dirty pages is
generally kept at 10% which matches vm.dirty_background_ratio which
is normal expected historical behaviour.
2. With the vanilla kernel, the ratio of Slab/Pagecache is close to
0.95 for much of the test i.e. Slab is being left alone and
dominating memory consumption. With the patch applied, the ratio
varies between 0.35 and 0.45 with the bulk of the measured ratios
roughly half way between those values. This is a different balance to
what Dave reported but it was at least consistent.
3. Slabs are scanned throughout the entire test with the patch applied.
The vanille kernel has periods with no scan activity and then
relatively massive spikes.
4. Without the patch, kswapd scan rates are very variable. With the
patch, the scan rates remain quite steady.
4. Overall vmstats are closer to normal expectations
5.3.0-rc3 5.3.0-rc3
vanilla shrinker-v1r1
Ops Direct pages scanned 99388.00 328410.00
Ops Kswapd pages scanned 45382917.00 33451026.00
Ops Kswapd pages reclaimed 30869570.00 25239655.00
Ops Direct pages reclaimed 74131.00 5830.00
Ops Kswapd efficiency % 68.02 75.45
Ops Kswapd velocity 5585.75 4002.25
Ops Page reclaim immediate 1179721.00 430927.00
Ops Slabs scanned 62367361.00 73581394.00
Ops Direct inode steals 2103.00 1002.00
Ops Kswapd inode steals 570180.00 5183206.00
o Vanilla kernel is hitting direct reclaim more frequently,
not very much in absolute terms but the fact the patch
reduces it is interesting
o "Page reclaim immediate" in the vanilla kernel indicates
dirty pages are being encountered at the tail of the LRU.
This is generally bad and means in this case that the LRU
is not long enough for dirty pages to be cleaned by the
background flush in time. This is much reduced by the
patch.
o With the patch, kswapd is reclaiming 10 times more slab
pages than with the vanilla kernel. This is indicative
of the watermark boosting over-protecting slab
A more complete set of tests were run that were part of the basis for
introducing boosting and while there are some differences, they are well
within tolerances.
Bottom line, the special casing kswapd to avoid slab behaviour is
unpredictable and can lead to abnormal results for normal workloads.
This patch restores the expected behaviour that slab and page cache is
balanced consistently for a workload with a steady allocation ratio of
slab/pagecache pages. It also means that if there are workloads that
favour the preservation of slab over pagecache that it can be tuned via
vm.vfs_cache_pressure where as the vanilla kernel effectively ignores
the parameter when boosting is active.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 1c30844d2dfe ("mm: reclaim small amounts of memory when an external fragmentation event occurs")
Signed-off-by: Mel Gorman <[email protected]>
Reviewed-by: Dave Chinner <[email protected]>
Acked-by: Vlastimil Babka <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: <[email protected]> [5.0+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
This reverts commit 2f0799a0ffc033b ("mm, thp: restore node-local
hugepage allocations").
commit 2f0799a0ffc033b was rightfully applied to avoid the risk of a
severe regression that was reported by the kernel test robot at the end
of the merge window. Now we understood the regression was a false
positive and was caused by a significant increase in fairness during a
swap trashing benchmark. So it's safe to re-apply the fix and continue
improving the code from there. The benchmark that reported the
regression is very useful, but it provides a meaningful result only when
there is no significant alteration in fairness during the workload. The
removal of __GFP_THISNODE increased fairness.
__GFP_THISNODE cannot be used in the generic page faults path for new
memory allocations under the MPOL_DEFAULT mempolicy, or the allocation
behavior significantly deviates from what the MPOL_DEFAULT semantics are
supposed to be for THP and 4k allocations alike.
Setting THP defrag to "always" or using MADV_HUGEPAGE (with THP defrag
set to "madvise") has never meant to provide an implicit MPOL_BIND on
the "current" node the task is running on, causing swap storms and
providing a much more aggressive behavior than even zone_reclaim_node =
3.
Any workload who could have benefited from __GFP_THISNODE has now to
enable zone_reclaim_mode=1||2||3. __GFP_THISNODE implicitly provided
the zone_reclaim_mode behavior, but it only did so if THP was enabled:
if THP was disabled, there would have been no chance to get any 4k page
from the current node if the current node was full of pagecache, which
further shows how this __GFP_THISNODE was misplaced in MADV_HUGEPAGE.
MADV_HUGEPAGE has never been intended to provide any zone_reclaim_mode
semantics, in fact the two are orthogonal, zone_reclaim_mode = 1|2|3
must work exactly the same with MADV_HUGEPAGE set or not.
The performance characteristic of memory depends on the hardware
details. The numbers below are obtained on Naples/EPYC architecture and
the N/A projection extends them to show what we should aim for in the
future as a good THP NUMA locality default. The benchmark used
exercises random memory seeks (note: the cost of the page faults is not
part of the measurement).
D0 THP | D0 4k | D1 THP | D1 4k | D2 THP | D2 4k | D3 THP | D3 4k | ...
0% | +43% | +45% | +106% | +131% | +224% | N/A | N/A
D0 means distance zero (i.e. local memory), D1 means distance one (i.e.
intra socket memory), D2 means distance two (i.e. inter socket memory),
etc...
For the guest physical memory allocated by qemu and for guest mode
kernel the performance characteristic of RAM is more complex and an
ideal default could be:
D0 THP | D1 THP | D0 4k | D2 THP | D1 4k | D3 THP | D2 4k | D3 4k | ...
0% | +58% | +101% | N/A | +222% | N/A | N/A | N/A
NOTE: the N/A are projections and haven't been measured yet, the
measurement in this case is done on a 1950x with only two NUMA nodes.
The THP case here means THP was used both in the host and in the guest.
After applying this commit the THP NUMA locality order that we'll get
out of MADV_HUGEPAGE is this:
D0 THP | D1 THP | D2 THP | D3 THP | ... | D0 4k | D1 4k | D2 4k | D3 4k | ...
Before this commit it was:
D0 THP | D0 4k | D1 4k | D2 4k | D3 4k | ...
Even if we ignore the breakage of large workloads that can't fit in a
single node that the __GFP_THISNODE implicit "current node" mbind
caused, the THP NUMA locality order provided by __GFP_THISNODE was still
not the one we shall aim for in the long term (i.e. the first one at
the top).
After this commit is applied, we can introduce a new allocator multi
order API and to replace those two alloc_pages_vmas calls in the page
fault path, with a single multi order call:
unsigned int order = (1 << HPAGE_PMD_ORDER) | (1 << 0);
page = alloc_pages_multi_order(..., &order);
if (!page)
goto out;
if (!(order & (1 << 0))) {
VM_WARN_ON(order != 1 << HPAGE_PMD_ORDER);
/* THP fault */
} else {
VM_WARN_ON(order != 1 << 0);
/* 4k fallback */
}
The page allocator logic has to be altered so that when it fails on any
zone with order 9, it has to try again with a order 0 before falling
back to the next zone in the zonelist.
After that we need to do more measurements and evaluate if adding an
opt-in feature for guest mode is worth it, to swap "DN 4k | DN+1 THP"
with "DN+1 THP | DN 4k" at every NUMA distance crossing.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Andrea Arcangeli <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Acked-by: Mel Gorman <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: David Rientjes <[email protected]>
Cc: Zi Yan <[email protected]>
Cc: Stefan Priebe - Profihost AG <[email protected]>
Cc: "Kirill A. Shutemov" <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
alloc_hugepage_direct_gfpmask""
Patch series "reapply: relax __GFP_THISNODE for MADV_HUGEPAGE mappings".
The fixes for what was originally reported as "pathological THP
behavior" we rightfully reverted to be sure not to introduced
regressions at end of a merge window after a severe regression report
from the kernel bot. We can safely re-apply them now that we had time
to analyze the problem.
The mm process worked fine, because the good fixes were eventually
committed upstream without excessive delay.
The regression reported by the kernel bot however forced us to revert
the good fixes to be sure not to introduce regressions and to give us
the time to analyze the issue further. The silver lining is that this
extra time allowed to think more at this issue and also plan for a
future direction to improve things further in terms of THP NUMA
locality.
This patch (of 2):
This reverts commit 356ff8a9a78fb35d ("Revert "mm, thp: consolidate THP
gfp handling into alloc_hugepage_direct_gfpmask"). So it reapplies
89c83fb539f954 ("mm, thp: consolidate THP gfp handling into
alloc_hugepage_direct_gfpmask").
Consolidation of the THP allocation flags at the same place was meant to
be a clean up to easier handle otherwise scattered code which is
imposing a maintenance burden. There were no real problems observed
with the gfp mask consolidation but the reversion was rushed through
without a larger consensus regardless.
This patch brings the consolidation back because this should make the
long term maintainability easier as well as it should allow future
changes to be less error prone.
[[email protected]: changelog additions]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Andrea Arcangeli <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: David Rientjes <[email protected]>
Cc: Zi Yan <[email protected]>
Cc: Stefan Priebe - Profihost AG <[email protected]>
Cc: "Kirill A. Shutemov" <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
A compiler throws a warning on an arm64 system since commit 9849a5697d3d
("arch, mm: convert all architectures to use 5level-fixup.h"),
mm/kasan/init.c: In function 'kasan_free_p4d':
mm/kasan/init.c:344:9: warning: variable 'p4d' set but not used [-Wunused-but-set-variable]
p4d_t *p4d;
^~~
because p4d_none() in "5level-fixup.h" is compiled away while it is a
static inline function in "pgtable-nopud.h".
However, if converted p4d_none() to a static inline there, powerpc would
be unhappy as it reads those in assembler language in
"arch/powerpc/include/asm/book3s/64/pgtable.h", so it needs to skip
assembly include for the static inline C function.
While at it, converted a few similar functions to be consistent with the
ones in "pgtable-nopud.h".
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Qian Cai <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Cc: Kirill A. Shutemov <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Jason Gunthorpe <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
If you use lseek or similar (e.g. pread) to access a location in a
seq_file file that is within a record, rather than at a record boundary,
then the first read will return the remainder of the record, and the
second read will return the whole of that same record (instead of the
next record). When seeking to a record boundary, the next record is
correctly returned.
This bug was introduced by a recent patch (identified below). Before
that patch, seq_read() would increment m->index when the last of the
buffer was returned (m->count == 0). After that patch, we rely on
->next to increment m->index after filling the buffer - but there was
one place where that didn't happen.
Link: https://lkml.kernel.org/lkml/[email protected]/
Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code and interface")
Signed-off-by: NeilBrown <[email protected]>
Reported-by: Sergei Turchanov <[email protected]>
Tested-by: Sergei Turchanov <[email protected]>
Cc: Alexander Viro <[email protected]>
Cc: Markus Elfring <[email protected]>
Cc: <[email protected]> [4.19+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Memcg counters for shadow nodes are broken because the memcg pointer is
obtained in a wrong way. The following approach is used:
virt_to_page(xa_node)->mem_cgroup
Since commit 4d96ba353075 ("mm: memcg/slab: stop setting
page->mem_cgroup pointer for slab pages") page->mem_cgroup pointer isn't
set for slab pages, so memcg_from_slab_page() should be used instead.
Also I doubt that it ever worked correctly: virt_to_head_page() should
be used instead of virt_to_page(). Otherwise objects residing on tail
pages are not accounted, because only the head page contains a valid
mem_cgroup pointer. That was a case since the introduction of these
counters by the commit 68d48e6a2df5 ("mm: workingset: add vmstat counter
for shadow nodes").
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 4d96ba353075 ("mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages")
Signed-off-by: Roman Gushchin <[email protected]>
Acked-by: Johannes Weiner <[email protected]>
Cc: Vladimir Davydov <[email protected]>
Cc: Shakeel Butt <[email protected]>
Cc: Michal Hocko <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Currently, when checking to see if accessing n bytes starting at address
"ptr" will cause a wraparound in the memory addresses, the check in
check_bogus_address() adds an extra byte, which is incorrect, as the
range of addresses that will be accessed is [ptr, ptr + (n - 1)].
This can lead to incorrectly detecting a wraparound in the memory
address, when trying to read 4 KB from memory that is mapped to the the
last possible page in the virtual address space, when in fact, accessing
that range of memory would not cause a wraparound to occur.
Use the memory range that will actually be accessed when considering if
accessing a certain amount of bytes will cause the memory address to
wrap around.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: f5509cc18daa ("mm: Hardened usercopy")
Signed-off-by: Prasad Sodagudi <[email protected]>
Signed-off-by: Isaac J. Manjarres <[email protected]>
Co-developed-by: Prasad Sodagudi <[email protected]>
Reviewed-by: William Kucharski <[email protected]>
Acked-by: Kees Cook <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Trilok Soni <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
If an error occurs during kmemleak_init() (e.g. kmem cache cannot be
created), kmemleak is disabled but kmemleak_early_log remains enabled.
Subsequently, when the .init.text section is freed, the log_early()
function no longer exists. To avoid a page fault in such scenario,
ensure that kmemleak_disable() also disables early logging.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Catalin Marinas <[email protected]>
Reported-by: Qian Cai <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|