| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use the port device rather than usb device in info and error messages.
This makes sure that driver and tty port is included in the messages,
while also making them more uniform.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Remove redundant check of num_interrupt_in which has already been
verified in probe (killing a NULL-urb would also have been fine).
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Return -ENODEV rather than -EINVAL on probe errors due to a missing
endpoint.
Also clean up the endpoint sanity check somewhat and use the interface
device for logging a more compact error in case an expected endpoint is
missing.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The adaptor can be found on development boards for 78k, RL78 and V850
microcontrollers produced by Renesas Electronics Corporation.
This is not a full-featured USB to serial converter, however it allows
basic communication and simple control which is enough for programming of
on-board flash and debugging through a debug monitor.
uPD78F0730 is a USB-enabled microcontroller with USB-to-UART conversion
implemented in firmware.
This chip is also present in some debugging adaptors which use it for
USB-to-SPI conversion as well. The present driver doesn't cover SPI,
only USB-to-UART conversion is supported.
Signed-off-by: Maksim Salau <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Do not report ASYNC_SKIP_TEST or ASYNC_AUTO_IRQ as being set in
TIOCGSERIAL handlers as these flags are not supported and do not really
make any sense for USB serial devices in the first place.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Clean up the ioctl handler and make sure to pass an unsigned-int rather
than serial_struct pointer to the TIOCSERGETLSR helper as this it what
the user argument really is.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Since commit 557aaa7ffab6 ("ft232: support the ASYNC_LOW_LATENCY
flag") the FTDI driver has been using a receive latency-timer value of
1 ms instead of the device default of 16 ms.
The latency timer is used to periodically empty a non-full receive
buffer, but a status header is always sent when the timer expires
including when the buffer is empty. This means that a two-byte bulk
message is received every millisecond also for an otherwise idle port as
long as it is open.
Let's restore the pre-2009 behaviour which reduces the rate of the
status messages to 1/16th (e.g. interrupt frequency drops from 1 kHz to
62.5 Hz) by not setting ASYNC_LOW_LATENCY by default.
Anyone willing to pay the price for the minimum-latency behaviour should
set the flag explicitly instead using the TIOCSSERIAL ioctl or a tool
such as setserial (e.g. setserial /dev/ttyUSB0 low_latency).
Note that since commit 0cbd81a9f6ba ("USB: ftdi_sio: remove
tty->low_latency") the ASYNC_LOW_LATENCY flag has no other effects but
to set a minimal latency timer.
Reported-by: Antoine Aubert <[email protected]>
Fixes: 557aaa7ffab6 ("ft232: support the ASYNC_LOW_LATENCY flag")
Cc: [email protected] # v2.6.31: e3e574ad85a2
Signed-off-by: Johan Hovold <[email protected]>
|
|
The opticon driver used a control request at open to trigger a CTS
status notification to be sent over the bulk-in pipe. When the driver
was converted to using the generic read implementation, an inverted test
prevented this request from being sent, something which could lead to
TIOCMGET reporting an incorrect CTS state.
Reported-by: Dan Carpenter <[email protected]>
Fixes: 7a6ee2b02751 ("USB: opticon: switch to generic read
implementation")
Cc: stable <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to detect and return an error on zero-length control-message
transfers when reading from the device.
This addresses a potential failure to detect an empty transmit buffer
during close.
Also remove a redundant check for short transfer when sending a command.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to detect short control-message transfers rather than continue
with zero-initialised data when retrieving modem status and during
device initialisation.
Fixes: 52af95459939 ("USB: add USB serial ssu100 driver")
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to detect short control transfers and return zero on success
when retrieving the modem status.
This fixes the TIOCMGET implementation which since e1ed212d8593 ("USB:
spcp8x5: add proper modem-status support") has returned TIOCM_LE on
successful retrieval, and avoids leaking bits from the stack on short
transfers.
This also fixes the carrier-detect implementation which since the above
mentioned commit unconditionally has returned true.
Fixes: e1ed212d8593 ("USB: spcp8x5: add proper modem-status support")
Cc: stable <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to detect short control-message transfers when fetching
modem and line state in open and when retrieving registers.
This specifically makes sure that an errno is returned to user space on
errors in TIOCMGET instead of a zero bitmask.
Also drop the unused getdevice function which also lacked appropriate
error handling.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver")
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to return an error on zero-length transfers when retrieving
the line settings even if the driver currently ignores the return value.
Also remove a redundant check for short transfer when setting the line
settings.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to detect short transfers when reading a device register.
The modem-status handling had sufficient error checks in place, but move
handling of short transfers into the register accessor function itself
for consistency.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to log an error on short transfers when reading a device
register.
Also clear the provided buffer (which if often an uninitialised
automatic variable) on errors as the driver currently does not bother to
check for errors.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to detect short control-message transfers so that errors are
logged when reading the modem status at open.
Note that while this also avoids initialising the modem status using
uninitialised heap data, these bits could not leak to user space as they
are currently not used.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Remove code that allocated but never used a buffer during open.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to detect short control-message transfers and log an error
when reading incomplete manufacturer and boot descriptors.
Note that the default all-zero descriptors will now be used after a
short transfer is detected instead of partially initialised ones.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Use a dedicated buffer for the DMA transfer and make sure to detect
short transfers to avoid parsing a corrupt descriptor.
Fixes: 6e8cf7751f9f ("USB: add EPIC support to the io_edgeport driver")
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to detect short responses when reading the latency timer to
avoid using stale buffer data.
Note that no heap data would currently leak through sysfs as
ASYNC_LOW_LATENCY is set by default.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to detect short responses when fetching the modem status in
order to avoid parsing uninitialised buffer data and having bits of it
leak to user space.
Note that we still allow for short 1-byte responses.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Fix open error handling which failed to detect errors when reading the
MSR and LSR registers, something which could lead to the shadow
registers being initialised from errnos.
Note that calling the generic close implementation is sufficient in the
error paths as the interrupt urb has not yet been submitted and the
register updates have not been made.
Fixes: f4c1e8d597d1 ("USB: ark3116: Make existing functions 16450-aware
and add close and release functions.")
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The current implementation failed to detect short transfers, something
which could lead to bits of the uninitialised heap transfer buffer
leaking to user space.
Fixes: 149fc791a452 ("USB: ark3116: Setup some basic infrastructure for
new ark3116 driver.")
Fixes: f4c1e8d597d1 ("USB: ark3116: Make existing functions 16450-aware
and add close and release functions.")
Cc: stable <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Remove unused termios structure from private data that was left by an
earlier purge by commit b1cff285ae8d ("usb serial: Eliminate bogus ioctl
code").
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Drop redundant packed attribute from the port-settings struct which is
already 1-byte aligned. Also replace __u8 with u8 for the field types as
this is not a structure we share with user space.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Remove dead and broken code that only served as a reminder to one day
implement modem control.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Replace a couple of dev_info with dev_dbg and remove another.
Also use the port device for logging, and include a radix prefix when
logging the baudrate.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Some CH340 devices appear unable to change the initial LCR settings, so
set a sane 8N1 default during probe to enable basic support for such
devices.
Also drop a redundant LCR read during device initialisation.
Signed-off-by: Johan Hovold <[email protected]>
|
|
Rename the line-control-register variable in set_termios to "lcr" and
use u8 type to match the shadow register.
Signed-off-by: Johan Hovold <[email protected]>
|
|
Rename the shadow modem-status register currently named "line_status" to
the less confusing "msr".
Also rename the helper function used to parse the interrupt data.
Signed-off-by: Johan Hovold <[email protected]>
|
|
Rename the shadow modem-control register currently named "line_control"
to the less confusing "mcr".
Signed-off-by: Johan Hovold <[email protected]>
|
|
Clean up the control-transfer debug messages by dropping redundant
information and unnecessary casts.
Signed-off-by: Johan Hovold <[email protected]>
|
|
The modem-status register was read as part of device configuration at
port_probe and then again at open (and reset-resume). During open (and
reset-resume) the MSR was read before submitting the interrupt URB,
something which could lead to an MSR-change going unnoticed when it
races with open (reset-resume).
Fix this by dropping the redundant reconfiguration of the port at every
open, and only read the MSR after the interrupt URB has been submitted.
Fixes: 664d5df92e88 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Signed-off-by: Johan Hovold <[email protected]>
|
|
The variable havedata was only being set but never used afterwards.
Signed-off-by: Sudip Mukherjee <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace fixes from Eric Biederman:
"This tree contains 4 fixes.
The first is a fix for a race that can causes oopses under the right
circumstances, and that someone just recently encountered.
Past that are several small trivial correct fixes. A real issue that
was blocking development of an out of tree driver, but does not appear
to have caused any actual problems for in-tree code. A potential
deadlock that was reported by lockdep. And a deadlock people have
experienced and took the time to track down caused by a cleanup that
removed the code to drop a reference count"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
sysctl: Drop reference added by grab_header in proc_sys_readdir
pid: fix lockdep deadlock warning due to ucount_lock
libfs: Modify mount_pseudo_xattr to be clear it is not a userspace mount
mnt: Protect the mountpoint hashtable with mount_lock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc driver fixes for 4.10-rc4 that resolve
some reported issues.
The MEI driver issue resolves a lot of problems that people have been
having, as does the mem driver fix. The other minor fixes resolve
other reported issues.
All of these have been in linux-next for a while"
* tag 'char-misc-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
vme: Fix wrong pointer utilization in ca91cx42_slave_get
auxdisplay: fix new ht16k33 build errors
ppdev: don't print a free'd string
extcon: return error code on failure
drivers: char: mem: Fix thinkos in kmem address checks
mei: bus: enable OS version only for SPT and newer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single patch being reverted to remove a feature that was
added in 4.10-rc1 that isn't quite ready for release.
It will be redone as a debugfs file instead of a sysfs file in the
future"
* tag 'driver-core-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Revert "driver core: Add deferred_probe attribute to devices in sysfs"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial driver fixes for 4.10-rc4 to resolve a
number of reported issues.
Nothing major here at all, one revert of a problematic patch, and some
other tiny bugfixes. Full details are in the shortlog below.
All have been in linux-next with no reported issues"
* tag 'tty-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
sysrq: attach sysrq handler correctly for 32-bit kernel
Revert "tty: serial: 8250: add CON_CONSDEV to flags"
Clearing FIFOs in RS485 emulation mode causes subsequent transmits to break
8250_pci: Fix potential use-after-free in error path
tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done
tty/serial: atmel_serial: BUG: stop DMA from transmitting in stop_tx
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a few small USB driver fixes for 4.10-rc4 to resolve some
reported issues.
The "largest" here is a number of bugs being fixed in the ch341
usb-serial driver, to hopefully resolve the mess of different devices
floating around that use this driver that have been having problems
with the 4.10-rc1 release.
There's also a tiny musb fix that I missed in the last pull request,
as well as the traditional xhci fix rounding out the batch.
All have been in linux-next with no reported issues"
* tag 'usb-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: fix deadlock at host remove by running watchdog correctly
USB: serial: ch341: fix control-message error handling
usb: musb: fix runtime PM in debugfs
wusbcore: Fix one more crypto-on-the-stack bug
USB: serial: kl5kusb105: fix line-state error handling
USB: serial: ch341: fix baud rate and line-control handling
USB: serial: ch341: fix line settings after reset-resume
USB: serial: ch341: fix resume after reset
USB: serial: ch341: fix open error handling
USB: serial: ch341: fix modem-control and B0 handling
USB: serial: ch341: fix open and resume after B0
USB: serial: ch341: fix initial modem-control state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Bugfixes for I2C. Mostly core this time which is a bit unusual but
nothing really scary in there"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: piix4: Avoid race conditions with IMC
i2c: fix spelling mistake: "insufficent" -> "insufficient"
i2c: print correct device invalid address
i2c: do not enable fall back to Host Notify by default
i2c: fix kernel memory disclosure in dev interface
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- unwinder fixes
- AMD CPU topology enumeration fixes
- microcode loader fixes
- x86 embedded platform fixes
- fix for a bootup crash that may trigger when clearcpuid= is used
with invalid values"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mpx: Use compatible types in comparison to fix sparse error
x86/tsc: Add the Intel Denverton Processor to native_calibrate_tsc()
x86/entry: Fix the end of the stack for newly forked tasks
x86/unwind: Include __schedule() in stack traces
x86/unwind: Disable KASAN checks for non-current tasks
x86/unwind: Silence warnings for non-current tasks
x86/microcode/intel: Use correct buffer size for saving microcode data
x86/microcode/intel: Fix allocation size of struct ucode_patch
x86/microcode/intel: Add a helper which gives the microcode revision
x86/microcode: Use native CPUID to tickle out microcode revision
x86/CPU: Add native CPUID variants returning a single datum
x86/boot: Add missing declaration of string functions
x86/CPU/AMD: Fix Bulldozer topology
x86/platform/intel-mid: Rename 'spidev' to 'mrfld_spidev'
x86/cpu: Fix typo in the comment for Anniedale
x86/cpu: Fix bootup crashes by sanitizing the argument of the 'clearcpuid=' command-line option
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull NOHZ fix from Ingo Molnar:
"This fixes an old NOHZ race where we incorrectly calculate the next
timer interrupt in certain circumstances where hrtimers are pending,
that can cause hard to reproduce stalled-values artifacts in
/proc/stat"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: Fix collision between tick and other hrtimers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc race fixes uncovered by fuzzing efforts, a Sparse fix, two PMU
driver fixes, plus miscellanous tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Reject non sampling events with precise_ip
perf/x86/intel: Account interrupts for PEBS errors
perf/core: Fix concurrent sys_perf_event_open() vs. 'move_group' race
perf/core: Fix sys_perf_event_open() vs. hotplug
perf/x86/intel: Use ULL constant to prevent undefined shift behaviour
perf/x86/intel/uncore: Fix hardcoded socket 0 assumption in the Haswell init code
perf/x86: Set pmu->module in Intel PMU modules
perf probe: Fix to probe on gcc generated symbols for offline kernel
perf probe: Fix --funcs to show correct symbols for offline module
perf symbols: Robustify reading of build-id from sysfs
perf tools: Install tools/lib/traceevent plugins with install-bin
tools lib traceevent: Fix prev/next_prio for deadline tasks
perf record: Fix --switch-output documentation and comment
perf record: Make __record_options static
tools lib subcmd: Add OPT_STRING_OPTARG_SET option
perf probe: Fix to get correct modname from elf header
samples/bpf trace_output_user: Remove duplicate sys/ioctl.h include
samples/bpf sock_example: Avoid getting ethhdr from two includes
perf sched timehist: Show total scheduling time
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"A number of regression fixes:
- Fix a boot hang on machines that have somewhat unusual memory map
entries of phys_addr=0x0 num_pages=0, which broke due to a recent
commit. This commit got cherry-picked from the v4.11 queue because
the bug is affecting real machines.
- Fix a boot hang also reported by KASAN, caused by incorrect init
ordering introduced by a recent optimization.
- Fix a recent robustification fix to allocate_new_fdt_and_exit_boot()
that introduced an invalid assumption. Neither bugs were seen in
the wild AFAIK"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Prune invalid memory map entries and fix boot regression
x86/efi: Don't allocate memmap through memblock after mm_init()
efi/libstub/arm*: Pass latest memory map to the kernel
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro.
The most notable fix here is probably the fix for a splice regression
("fix a fencepost error in pipe_advance()") noticed by Alan Wylie.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix a fencepost error in pipe_advance()
coredump: Ensure proper size of sparse core files
aio: fix lock dep warning
tmpfs: clear S_ISGID when setting posix ACLs
|
|
Pull block fixes from Jens Axboe:
- the virtio_blk stack DMA corruption fix from Christoph, fixing and
issue with VMAP stacks.
- O_DIRECT blkbits calculation fix from Chandan.
- discard regression fix from Christoph.
- queue init error handling fixes for nbd and virtio_blk, from Omar and
Jeff.
- two small nvme fixes, from Christoph and Guilherme.
- rename of blk_queue_zone_size and bdev_zone_size to _sectors instead,
to more closely follow what we do in other places in the block layer.
This interface is new for this series, so let's get the naming right
before releasing a kernel with this feature. From Damien.
* 'for-linus' of git://git.kernel.dk/linux-block:
block: don't try to discard from __blkdev_issue_zeroout
sd: remove __data_len hack for WRITE SAME
nvme: use blk_rq_payload_bytes
scsi: use blk_rq_payload_bytes
block: add blk_rq_payload_bytes
block: Rename blk_queue_zone_size and bdev_zone_size
nvme: apply DELAY_BEFORE_CHK_RDY quirk at probe time too
nvme-rdma: fix nvme_rdma_queue_is_ready
virtio_blk: fix panic in initialization error path
nbd: blk_mq_init_queue returns an error code on failure, not NULL
virtio_blk: avoid DMA to stack for the sense buffer
do_direct_IO: Use inode->i_blkbits to compute block count to be cleaned
|
|
The logics in pipe_advance() used to release all buffers past the new
position failed in cases when the number of buffers to release was equal
to pipe->buffers. If that happened, none of them had been released,
leaving pipe full. Worse, it was trivial to trigger and we end up with
pipe full of uninitialized pages. IOW, it's an infoleak.
Cc: [email protected] # v4.9
Reported-by: "Alan J. Wylie" <[email protected]>
Tested-by: "Alan J. Wylie" <[email protected]>
Signed-off-by: Al Viro <[email protected]>
|
|
If the last section of a core file ends with an unmapped or zero page,
the size of the file does not correspond with the last dump_skip() call.
gdb complains that the file is truncated and can be confusing to users.
After all of the vma sections are written, make sure that the file size
is no smaller than the current file position.
This problem can be demonstrated with gdb's bigcore testcase on the
sparc architecture.
Signed-off-by: Dave Kleikamp <[email protected]>
Cc: Alexander Viro <[email protected]>
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Al Viro <[email protected]>
|
|
lockdep reports a warnning. file_start_write/file_end_write only
acquire/release the lock for regular files. So checking the files in aio
side too.
[ 453.532141] ------------[ cut here ]------------
[ 453.533011] WARNING: CPU: 1 PID: 1298 at ../kernel/locking/lockdep.c:3514 lock_release+0x434/0x670
[ 453.533011] DEBUG_LOCKS_WARN_ON(depth <= 0)
[ 453.533011] Modules linked in:
[ 453.533011] CPU: 1 PID: 1298 Comm: fio Not tainted 4.9.0+ #964
[ 453.533011] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.0-1.fc24 04/01/2014
[ 453.533011] ffff8803a24b7a70 ffffffff8196cffb ffff8803a24b7ae8 0000000000000000
[ 453.533011] ffff8803a24b7ab8 ffffffff81091ee1 ffff8803a5dba700 00000dba00000008
[ 453.533011] ffffed0074496f59 ffff8803a5dbaf54 ffff8803ae0f8488 fffffffffffffdef
[ 453.533011] Call Trace:
[ 453.533011] [<ffffffff8196cffb>] dump_stack+0x67/0x9c
[ 453.533011] [<ffffffff81091ee1>] __warn+0x111/0x130
[ 453.533011] [<ffffffff81091f97>] warn_slowpath_fmt+0x97/0xb0
[ 453.533011] [<ffffffff81091f00>] ? __warn+0x130/0x130
[ 453.533011] [<ffffffff8191b789>] ? blk_finish_plug+0x29/0x60
[ 453.533011] [<ffffffff811205d4>] lock_release+0x434/0x670
[ 453.533011] [<ffffffff8198af94>] ? import_single_range+0xd4/0x110
[ 453.533011] [<ffffffff81322195>] ? rw_verify_area+0x65/0x140
[ 453.533011] [<ffffffff813aa696>] ? aio_write+0x1f6/0x280
[ 453.533011] [<ffffffff813aa6c9>] aio_write+0x229/0x280
[ 453.533011] [<ffffffff813aa4a0>] ? aio_complete+0x640/0x640
[ 453.533011] [<ffffffff8111df20>] ? debug_check_no_locks_freed+0x1a0/0x1a0
[ 453.533011] [<ffffffff8114793a>] ? debug_lockdep_rcu_enabled.part.2+0x1a/0x30
[ 453.533011] [<ffffffff81147985>] ? debug_lockdep_rcu_enabled+0x35/0x40
[ 453.533011] [<ffffffff812a92be>] ? __might_fault+0x7e/0xf0
[ 453.533011] [<ffffffff813ac9bc>] do_io_submit+0x94c/0xb10
[ 453.533011] [<ffffffff813ac2ae>] ? do_io_submit+0x23e/0xb10
[ 453.533011] [<ffffffff813ac070>] ? SyS_io_destroy+0x270/0x270
[ 453.533011] [<ffffffff8111d7b3>] ? mark_held_locks+0x23/0xc0
[ 453.533011] [<ffffffff8100201a>] ? trace_hardirqs_on_thunk+0x1a/0x1c
[ 453.533011] [<ffffffff813acb90>] SyS_io_submit+0x10/0x20
[ 453.533011] [<ffffffff824f96aa>] entry_SYSCALL_64_fastpath+0x18/0xad
[ 453.533011] [<ffffffff81119190>] ? trace_hardirqs_off_caller+0xc0/0x110
[ 453.533011] ---[ end trace b2fbe664d1cc0082 ]---
Cc: Dmitry Monakhov <[email protected]>
Cc: Jan Kara <[email protected]>
Cc: Christoph Hellwig <[email protected]>
Cc: Al Viro <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Shaohua Li <[email protected]>
Signed-off-by: Al Viro <[email protected]>
|