| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
According to the datasheet, PLL lock time typically takes 2 msec and
at most takes 7 msec.
Check the lock status every 1 msec and exit the workaround if PLL is
locked.
Signed-off-by: Tzung-Bi Shih <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
It was observed Baytrail-based chromebooks could cause continuous PLL
unlocked when using playback stream and capture stream simultaneously.
Specifically, starting a capture stream after started a playback stream.
As a result, the audio data could corrupt or turn completely silent.
As the datasheet suggested, the maximum PLL lock time should be 7 msec.
The workaround resets the codec softly by toggling SHDN off and on if
PLL failed to lock for 10 msec. Notably, there is no suggested hold
time for SHDN off.
On Baytrail-based chromebooks, it would easily happen continuous PLL
unlocked if there is a 10 msec delay between SHDN off and on. Removes
the msleep().
Signed-off-by: Tzung-Bi Shih <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
The simple-card tries to signal the codec to disable rate constraints,
see commit 2458adb8f92a ("SoC: simple-card-utils: set 0Hz to sysclk when
shutdown"). This wasn't handled by the codec, instead it would set the
FLL frequency to 0Hz which isn't working. Since we don't have any rate
constraints just ignore this request.
Fixes: 13409d27cb39 ("ASoC: wm8904: configure sysclk/FLL automatically")
Signed-off-by: Michael Walle <[email protected]>
Acked-by: Charles Keepax <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
If CONFIG_SPI is n, SND_SOC_RT5677_SPI also is n, building fails:
sound/soc/codecs/rt5677.o: In function `rt5677_irq':
rt5677.c:(.text+0x2dbf): undefined reference to `rt5677_spi_hotword_detected'
sound/soc/codecs/rt5677.o: In function `rt5677_dsp_work':
rt5677.c:(.text+0x3709): undefined reference to `rt5677_spi_write'
This adds stub helpers to fix this.
Reported-by: Hulk Robot <[email protected]>
Fixes: 461c623270e4 ("ASoC: rt5677: Load firmware via SPI using delayed work")
Signed-off-by: YueHaibing <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Link unload now fails for ESAI/SAI DAIs with:
"error: invalid DAI type 6" because DAI type is not
properly handled.
Fix this by correctly handling cases where type is ESAI or SAI.
Fixes: a4eff5f86c9c5e7 ("ASoC: SOF: imx: Read ESAI parameters and send them to DSP")
Signed-off-by: Daniel Baluta <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The shim registers in BYT/CHT/BSW are 64bits based, correct the
copy/paste (from bdw.c where the shim registers are 32bits based) error
in byt_dump().
Fixes: 3a9e204d4e36 ("ASoC: SOF: Intel: Add context data to any IPC timeout")
Signed-off-by: Keyon Jie <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Some usages only call startup and shutdown without setting hw_params
(e.g. arecord --dump-hw-params). If we don't enable clk in startup, it
will cause ref count error because the clk will be disabled in shutdown.
For this reason, we should move enabling clk from hw_params to startup.
In addition, the hw_params is fixed in this driver(48000 rate, 2
channels, S16_LE format) so we don't need to change the clk rate after
the hw_params is set.
Signed-off-by: Yu-Hsuan Hsu <[email protected]>
Acked-by: Akshu Agrawal <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This patch modified the HW initial setting to fix i2c arbitration lost issue.
Signed-off-by: Shuming Fan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Current code:
LENOVO-20QE000VMC-ThinkPadX1Carbon7th-20QE000VMC
With the patch:
LENOVO-20QE000VMC-ThinkPadX1Carbon7th
Signed-off-by: Jaroslav Kysela <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
Add append_dmi_string() function and make the code more readable.
Signed-off-by: Jaroslav Kysela <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This reverts commit 957ce0c6b8a1f (ASoC: soc-pcm: check symmetry after
hw_params).
That commit cause soc_pcm_params_symmetry can't take effect.
cpu_dai->rate, cpu_dai->channels and cpu_dai->sample_bits
are updated in the middle of soc_pcm_hw_params, so move
soc_pcm_params_symmetry to the end of soc_pcm_hw_params is
not a good solution, for judgement of symmetry in the function
is always true.
FIXME:
According to the comments of that commit, I think the case
described in the commit should disable symmetric_rates
in Back-End, rather than changing the position of
soc_pcm_params_symmetry.
Signed-off-by: Shengjiu Wang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The RST (reset-gpios) is low active so the driver must handle it
accordingly.
Add comments to explain clearly how the line is used.
Signed-off-by: Peter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Use the standard name for the gpion in DT: reset-gpios
Document that the RST line is low active and update the example
accordingly.
Signed-off-by: Peter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add SND_SOC_BYTES_E to accept getter and putter.
Signed-off-by: Tzung-Bi Shih <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This ASCII string can carry additional information about
soundcard components or configuration. Add the possibility
to set this string via the ASoC card.
Signed-off-by: Jaroslav Kysela <[email protected]>
Cc: Mark Brown <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
soc-topology adds extra dai_link by using snd_soc_add_dai_link(),
and removes it by snd_soc_romove_dai_link().
This snd_soc_add/remove_dai_link() and/or its related
functions are unbalanced before, and now, these are balance-uped.
But, it finds the random operation issue, and it is reported by
Pierre-Louis.
When card was released, topology will call snd_soc_remove_dai_link()
via (A).
static void soc_cleanup_card_resources(struct snd_soc_card *card)
{
struct snd_soc_dai_link *link, *_link;
/* This should be called before snd_card_free() */
(A) soc_remove_link_components(card);
/* free the ALSA card at first; this syncs with pending operations */
if (card->snd_card) {
(B) snd_card_free(card->snd_card);
card->snd_card = NULL;
}
/* remove and free each DAI */
(X) soc_remove_link_dais(card);
for_each_card_links_safe(card, link, _link)
(C) snd_soc_remove_dai_link(card, link);
...
}
At (A), topology calls snd_soc_remove_dai_link().
Then topology rtd, and its related all data are freed.
Next, (B) is called, and then, pcm->private_free = soc_pcm_private_free()
is called.
static void soc_pcm_private_free(struct snd_pcm *pcm)
{
struct snd_soc_pcm_runtime *rtd = pcm->private_data;
/* need to sync the delayed work before releasing resources */
flush_delayed_work(&rtd->delayed_work);
snd_soc_pcm_component_free(rtd);
}
Here, it gets rtd via pcm->private_data.
But, topology related rtd are already freed at (A).
Normal sound card has no damage, becase it frees rtd at (C).
These are finalizing rtd related data.
Thus, these should be called when rtd was freed, not sound card
was freed. It is very natural and understandable.
In other words, pcm->private_free = soc_pcm_private_free()
is no longer needed.
Extra issue is that there is zero chance to call
soc_remove_dai() for topology related dai at (X).
Because (A) removes rtd connection from card too, and,
(X) is based on card connected rtd.
This means, (X) need to be called before (C) (= for normal sound)
and (A) (= for topology).
Now, I want to focus this patch which is the reason why
snd_card_free() = (B) is located there.
commit 4efda5f2130da033aeedc5b3205569893b910de2
("ASoC: Fix use-after-free at card unregistration")
Original snd_card_free() was called last of this function.
But moved to top to avoid use-after-free issue.
The issue was happen at soc_pcm_free() which was pcm->private_free,
today it is updated/renamed to soc_pcm_private_free().
In other words, (B) need to be called before (C) (= for normal sound)
and (A) (= for topology), because it needs (not yet freed) rtd.
But, (A) need to be called before (B),
because it needs card->snd_card pointer.
If we call flush_delayed_work() and snd_soc_pcm_component_free()
(= same as soc_pcm_private_free()) when rtd was freed (= (C), (A)),
there is no reason to call snd_card_free() at top of this function.
It can be called end of this function, again.
But, in such case, it will likely break unbind again, as Takashi-san
reported. When unbind is performed in a busy state, the code may
release still-in-use resources.
At least we need to call snd_card_disconnect_sync() at the first place.
The final code will be...
static void soc_cleanup_card_resources(struct snd_soc_card *card)
{
struct snd_soc_dai_link *link, *_link;
if (card->snd_card)
(Z) snd_card_disconnect_sync(card->snd_card);
(X) soc_remove_link_dais(card);
(A) soc_remove_link_components(card);
for_each_card_links_safe(card, link, _link)
(C) snd_soc_remove_dai_link(card, link);
...
if (card->snd_card) {
(B) snd_card_free(card->snd_card);
card->snd_card = NULL;
}
}
To avoid release still-in-use resources,
call snd_card_disconnect_sync() at (Z).
(X) is needed for both non-topology and topology.
topology removes rtd via (A), and
non topology removes rtd via (C).
snd_card_free() is no longer related to use-after-free issue.
Thus, locating (B) is no problem.
Fixes: df95a16d2a9626 ("ASoC: soc-core: fix RIP warning on card removal")
Fixes: bc7a9091e5b927 ("ASoC: soc-core: add soc_unbind_dai_link()")
Reported-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Kuninori Morimoto <[email protected]>
Tested-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This patch uses rtd instead of pcm at snd_soc_pcm_component_new/free()
parameter.
This is prepare for dai_link remove bug fix on topology.
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Expose mixer control API for reading and writing controls from the kernel.
This API can be used by ALSA kernel drivers with ADSP support to
read and write firmware-defined memory regions.
Signed-off-by: Li Xu <[email protected]>
Signed-off-by: David Rhodes <[email protected]>
Acked-by: Charles Keepax <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The tlv320aic31xx devices allow to adjust the output common-mode voltage
for best analog performance. The datasheet states that the common mode
voltage should be set to be <= AVDD/2.
This changes allows to configure the output common-mode voltage via a DT
property. If the property is absent the voltage is automatically chosen
as the highest voltage below/equal to AVDD/2.
Signed-off-by: Lucas Stach <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The manifest information is different between CNL, CML and CFL platforms
hence we need to load different files.
Signed-off-by: Liam Girdwood <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
In case the RST line is connected to a GPIO line it needs to be pulled high
when the driver probes to be able to use the codec.
Add support also for cases when more than one codec is is controlled by the
same GPIO line by requesting the gpio with GPIOD_FLAGS_BIT_NONEXCLUSIVE.
Signed-off-by: Peter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
On boards where the RST line is not pulled up, but it is connected to a
GPIO line this property must present in order to be able to enable the
codec.
Signed-off-by: Peter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The driver forgets to call pm_runtime_disable in remove and
probe failure.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <[email protected]>
Acked-by: Charles Keepax <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This driver misses calls to pm_runtime_disable and regulator_bulk_disable
in remove and a call to free_irq in probe failure.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Qualcomm DSPs also support the flac decoder, so add support for FLAC
decoder and convert the snd_dec_flac params to qdsp format.
Co-developed-by: Srinivas Kandagatla <[email protected]>
Signed-off-by: Srinivas Kandagatla <[email protected]>
Signed-off-by: Vinod Koul <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Qualcomm DSPs expect flac config to be set for flac decoders, so add the
API to program the flac config to the DSP
Signed-off-by: Srinivas Kandagatla <[email protected]>
Signed-off-by: Vinod Koul <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The current design of sending codec parameters assumes that decoders
will have parsers so they can parse the encoded stream for parameters
and configure the decoder.
But this assumption may not be universally true and we know some DSPs
which do not contain the parsers so additional parameters are required
to be passed.
So add these parameters starting with FLAC decoder. The size of
snd_codec_options is still 120 bytes after this change (due to this
being a union)
Co-developed-by: Srinivas Kandagatla <[email protected]>
Signed-off-by: Srinivas Kandagatla <[email protected]>
Signed-off-by: Vinod Koul <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Acked-by: Takashi Iwai <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
Fixes: 21c00e5df439 ("ASoC: rt5677: Enable jack detect while DSP is running")
Signed-off-by: kbuild test robot <[email protected]>
Link: https://lore.kernel.org/r/20191114153304.n4pyix7qadu76tx4@4978f4969bb8
Signed-off-by: Mark Brown <[email protected]>
|
|
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
soc_cleanup_card_resources() will call card->remove(), but it should be
called if card->probe() or card->late_probe() are called.
snd_soc_bind_card() might be error before calling
card->probe() / card->late_probe().
In that time, card->remove() will be called.
This patch adds card_probed parameter to judge it.
Fixes: bfce78a559655 ("ASoC: soc-core: tidyup soc_init_dai_link()")
Signed-off-by: Kuninori Morimoto <[email protected]>
Tested-by: Jon Hunter <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
To makes code readable, this patch moves snd_soc_unbind_card() next
to snd_soc_bind_card().
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
snd_soc_bind_card() is calling snd_soc_dapm_init() for both
card and component.
Let's call paired snd_soc_dapm_shutdown() at paired
soc_cleanup_card_resources().
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
There is a block that is indented too deeply, remove
the extraneous tabs.
Signed-off-by: Colin Ian King <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
'fsia' and 'fsib' property prefixes were added as schema in commit
2f52475bac7e ("ASoC: fsi: switch to yaml base Documentation").
Unfortunately to do checks on actual vendor prefixes, we have to track
the handful of prefixes which are not vendors like 'fsia' and 'fsib'.
Fixes: 2f52475bac7e ASoC: fsi: switch to yaml base Documentation
Cc: Kuninori Morimoto <[email protected]>
Cc: Mark Brown <[email protected]>
Signed-off-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
snd_soc_bind_card() is calling many initialize functions
for each card / link / dai / aux etc, etc, etc...
When error happen, the message is indicated at snd_soc_bind_card(),
not at each functions.
But, only soc_probe_aux_devices() case is indicating error at functions,
not at snd_soc_bind_card().
It is not an issue, but unbalanced.
This patch moves error message to snd_soc_bind_card().
Also avoids deep-nested code.
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
having both soc_bind_card() and snd_soc_instantiate_card() is
very confusable. Let's merge these.
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
having both soc_remove_component() and soc_cleanup_component() is
very confusable. Let's merge these.
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
We don't need to separete snd_soc_remove_dai_link() and
soc_unbind_dai_link() anymore. Let's merge these.
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
We don't need to separete snd_soc_add_dai_link() and
soc_bind_dai_link() anymore. Let's merge these.
One note is that before this patch, it adds list (A)
eventhough if it had dai_link->ignore (1), or already bounded dai_link (2).
But I guess it is wrong. This patch also solve this issue.
/* BEFORE */
int soc_bind_dai_link(...)
{
...
(1) if (dai_link->ignore)
return 0;
(2) if (soc_is_dai_link_bound(...))
return 0;
...
}
int snd_soc_add_dai_link(...)
{
...
=> ret = soc_bind_dai_link(...);
=> if (ret < 0)
=> return ret;
(A) list_add_tail(&dai_link->list, &card->dai_link_list);
...
}
/* AFTER */
int snd_soc_add_dai_link(...)
{
...
(1) if (dai_link->ignore)
return 0;
(2) if (soc_is_dai_link_bound(...))
return 0;
...
(A) list_add_tail(&dai_link->list, &card->dai_link_list);
return 0;
}
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
We don't need to separete snd_soc_unregister_dai() and
soc_del_dai() anymore. Let's merge these
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
We don't need to separete snd_soc_register_dai() and
soc_add_dai() anymore. Let's merge these
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Because complex separeted "card pre-listed component" and
"topology added component" duplicated operation is now
becoming simple, we don't need to check already bound dai_link
which is not exist anymore.
This patch removes soc_is_dai_link_bound().
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The volume and bytes kcontrols are currently not freeing their
memory on initialization failures. When an error occurs, all the
widgets loaded so far are unloaded via sof_widget_unload().
But this only happens for the widgets that got successfully loaded.
Fix that by kfree()-ing the allocated memory on load error.
Fixes: 311ce4fe7637d ("ASoC: SOF: Add support for loading topologies")
Reviewed-by: Paul Olaru <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Signed-off-by: Dragos Tarcatu <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
We should suspend audio to D3 by default, for the sake of power saving,
change the condition of D0I3 suspending here to that when there is
stream with suspend_ignored specified.
Signed-off-by: Keyon Jie <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add helper to check if the DSP should be put in D0i3. This function
returns true if a stream has ignored the SUSPEND trigger to keep the
pipelines running in the DSP.
Signed-off-by: Keyon Jie <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add check before seeting d0_substate and return success if Audio DSP is
already in the target substate.
Signed-off-by: Keyon Jie <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add Audio DSP state machine with comments. Note that the
'D0<-->runtime D0I3' part is not implemented yet.
Signed-off-by: Keyon Jie <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
We have platforms such as CFL with no known I2S codec being used, and
the ACPI tables are currently empty, so fall-back to using the
firmware filename used in nocodec mode
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|