| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Somehow two copies of the line 'up_write(&vf->efx->filter_sem);' got into
efx_ef10_sriov_set_vf_vlan(). This would put the mutex in a bad state and
cause all subsequent down attempts to hang.
Fixes: 671b53eec2ed ("sfc: Ensure down_write(&filter_sem) and up_write() are matched before calling efx_net_open()")
Signed-off-by: Edward Cree <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Network interface groups support added while ago, however
there is no IFLA_GROUP attribute description in policy
and netlink message size calculations until now.
Add IFLA_GROUP attribute to the policy.
Fixes: cbda10fa97d7 ("net_device: add support for network device groups")
Signed-off-by: Serhey Popovych <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
While commit 73ba57bfae4a ("ipv6: fix backtracking for throw routes")
does good job on error propagation to the fib_rules_lookup()
in fib rules core framework that also corrects throw routes
handling, it does not solve route reference leakage problem
happened when we return -EAGAIN to the fib_rules_lookup()
and leave routing table entry referenced in arg->result.
If rule with matched throw route isn't last matched in the
list we overwrite arg->result losing reference on throw
route stored previously forever.
We also partially revert commit ab997ad40839 ("ipv6: fix the
incorrect return value of throw route") since we never return
routing table entry with dst.error == -EAGAIN when
CONFIG_IPV6_MULTIPLE_TABLES is on. Also there is no point
to check for RTF_REJECT flag since it is always set throw
route.
Fixes: 73ba57bfae4a ("ipv6: fix backtracking for throw routes")
Signed-off-by: Serhey Popovych <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The lan911x family of devices require supplying from 3.3 V power
supplies (connected to VDD_IO, VDD_A and VREG_3.3 pins). The existing
driver however obtains only VDD_IO and VDD_A regulators in an optional
way so document this in bindings.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Madalin Bucur says:
====================
net: fix loadable module for DPAA Ethernet
The DPAA Ethernet makes use of a symbol that is not exported.
Address the issue by propagating the dma_ops rather than calling
arch_setup_dma_ops().
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Remove the use of arch_setup_dma_ops() that was not exported
and was breaking loadable module compilation.
Signed-off-by: Madalin Bucur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Make sure dma_ops are set, to be later used by the Ethernet driver.
Signed-off-by: Madalin Bucur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Since commit 217f69743681 ("net: busy-poll: allow preemption in
sk_busy_loop()") there is an explicit do_softirq() invocation after
local_bh_enable() has been invoked.
I don't understand why we need this because local_bh_enable() will
invoke do_softirq() once the softirq counter reached zero and we have
softirq-related work pending.
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We should avoid marking goto rules unresolved when their
target is actually reachable after rule deletion.
Consolder following sample scenario:
# ip -4 ru sh
0: from all lookup local
32000: from all goto 32100
32100: from all lookup main
32100: from all lookup default
32766: from all lookup main
32767: from all lookup default
# ip -4 ru del pref 32100 table main
# ip -4 ru sh
0: from all lookup local
32000: from all goto 32100 [unresolved]
32100: from all lookup default
32766: from all lookup main
32767: from all lookup default
After removal of first rule with preference 32100 we
mark all goto rules as unreachable, even when rule with
same preference as removed one still present.
Check if next rule with same preference is available
and make all rules with goto action pointing to it.
Signed-off-by: Serhey Popovych <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fixes resume from suspend.
bug: https://bugzilla.kernel.org/show_bug.cgi?id=196121
Reported-by: Przemek <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
Disable PX on these systems.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=101491
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
Signed-off-by: Alex Deucher <[email protected]>
|
|
Increase the default display clock on newer asics to
accomodate some high res modes with really high refresh
rates.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=93826
Acked-by: Chunming Zhou <[email protected]>
Acked-by: Christian König <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
We were using the wrong structure which lead to an overflow
on some boards.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=101387
Acked-by: Chunming Zhou <[email protected]>
Acked-by: Christian König <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-misc-next-fixes
UAPI Changes:
- vc4: Add get/set tiling format ioctls (Eric)
Driver Changes:
- vc4: Add tiling T-format support for scanout (Eric)
- vc4: Use atomic helpers in commit (Boris)
Cc: Boris Brezillon <[email protected]>
Cc: Eric Anholt <[email protected]>
Signed-off-by: Sean Paul <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620151126.zobksbwjgtp5wawe@art_vandelay
|
|
Backmerging airlied/drm-next
|
|
Clock name has been updated during driver/DT binding review:
https://lkml.org/lkml/2016/12/13/718
Update DT binding doc to reflect this.
Fixes: 8f9359c6c6a0 (dt-bindings: mfd: Add bindings for STM32 Timers driver)
Signed-off-by: Fabrice Gasnier <[email protected]>
Acked-by: Benjamin Gaignard <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
|
|
This commit fixes a "maybe-uninitialized" build failure in
arch/mips/kvm/tlb.c when KVM, DYNAMIC_DEBUG and JUMP_LABEL are all
enabled. The failure is:
In file included from ./include/linux/printk.h:329:0,
from ./include/linux/kernel.h:13,
from ./include/asm-generic/bug.h:15,
from ./arch/mips/include/asm/bug.h:41,
from ./include/linux/bug.h:4,
from ./include/linux/thread_info.h:11,
from ./include/asm-generic/current.h:4,
from ./arch/mips/include/generated/asm/current.h:1,
from ./include/linux/sched.h:11,
from arch/mips/kvm/tlb.c:13:
arch/mips/kvm/tlb.c: In function ‘kvm_mips_host_tlb_inv’:
./include/linux/dynamic_debug.h:126:3: error: ‘idx_kernel’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
__dynamic_pr_debug(&descriptor, pr_fmt(fmt), \
^~~~~~~~~~~~~~~~~~
arch/mips/kvm/tlb.c:169:16: note: ‘idx_kernel’ was declared here
int idx_user, idx_kernel;
^~~~~~~~~~
There is a similar error relating to "idx_user". Both errors were
observed with GCC 6.
As far as I can tell, it is impossible for either idx_user or idx_kernel
to be uninitialized when they are later read in the calls to kvm_debug,
but to satisfy the compiler, add zero initializers to both variables.
Signed-off-by: James Cowgill <[email protected]>
Fixes: 57e3869cfaae ("KVM: MIPS/TLB: Generalise host TLB invalidate to kernel ASID")
Cc: <[email protected]> # 4.11+
Acked-by: James Hogan <[email protected]>
Signed-off-by: Radim Krčmář <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-linus
Pull xen-blkback fixes from Konrad:
"Security and memory leak fixes in xen block driver."
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* fix problems that could cause hangs or crashes in the host on POWER9
* fix problems that could allow guests to potentially affect or disrupt
the execution of the controlling userspace
|
|
As it turns out more than just Armada 370 and XP support using GPIO
lines as PWM lines. For example the Armada 38x family has the same
hardware support. As such "marvell,armada-370-xp-gpio" for the
compatible string is a misnomer.
Change the compatible string to "marvell,armada-370-gpio" before the
driver makes it out of the -rc stage. This also follows the practice of
using only the first device family supported as part of the name.
Also update the documentation and comments in the code accordingly.
Fixes: 757642f9a584 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Ralph Sennhauser <[email protected]>
Acked-by: Gregory CLEMENT <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
https://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull clockevents fixes from Daniel Lezcano:
- Fixed wrong iomem area unmapped in the arch_arm_timer (Frank Rowand)
- Added missing includes for sun5i and cadence-ttc (Stephen Rothwell)
|
|
|
|
rcu_read_(un)lock(), list_*_rcu(), and synchronize_rcu() are used for a secure
access and manipulation of the list of patches that modify the same function.
In particular, it is the variable func_stack that is accessible from the ftrace
handler via struct ftrace_ops and klp_ops.
Of course, it synchronizes also some states of the patch on the top of the
stack, e.g. func->transition in klp_ftrace_handler.
At the same time, this mechanism guards also the manipulation of
task->patch_state. It is modified according to the state of the transition and
the state of the process.
Now, all this works well as long as RCU works well. Sadly livepatching might
get into some corner cases when this is not true. For example, RCU is not
watching when rcu_read_lock() is taken in idle threads. It is because they
might sleep and prevent reaching the grace period for too long.
There are ways how to make RCU watching even in idle threads, see
rcu_irq_enter(). But there is a small location inside RCU infrastructure when
even this does not work.
This small problematic location can be detected either before calling
rcu_irq_enter() by rcu_irq_enter_disabled() or later by rcu_is_watching().
Sadly, there is no safe way how to handle it. Once we detect that RCU was not
watching, we might see inconsistent state of the function stack and the related
variables in klp_ftrace_handler(). Then we could do a wrong decision, use an
incompatible implementation of the function and break the consistency of the
system. We could warn but we could not avoid the damage.
Fortunately, ftrace has similar problems and they seem to be solved well there.
It uses a heavy weight implementation of some RCU operations. In particular, it
replaces:
+ rcu_read_lock() with preempt_disable_notrace()
+ rcu_read_unlock() with preempt_enable_notrace()
+ synchronize_rcu() with schedule_on_each_cpu(sync_work)
My understanding is that this is RCU implementation from a stone age. It meets
the core RCU requirements but it is rather ineffective. Especially, it does not
allow to batch or speed up the synchronize calls.
On the other hand, it is very trivial. It allows to safely trace and/or
livepatch even the RCU core infrastructure. And the effectiveness is a not a
big issue because using ftrace or livepatches on productive systems is a rare
operation. The safety is much more important than a negligible extra load.
Note that the alternative implementation follows the RCU principles. Therefore,
we could and actually must use list_*_rcu() variants when manipulating the
func_stack. These functions allow to access the pointers in the right
order and with the right barriers. But they do not use any other
information that would be set only by rcu_read_lock().
Also note that there are actually two problems solved in ftrace:
First, it cares about the consistency of RCU read sections. It is being solved
the way as described and used in this patch.
Second, ftrace needs to make sure that nobody is inside the dynamic trampoline
when it is being freed. For this, it also calls synchronize_rcu_tasks() in
preemptive kernel in ftrace_shutdown().
Livepatch has similar problem but it is solved by ftrace for free.
klp_ftrace_handler() is a good guy and never sleeps. In addition, it is
registered with FTRACE_OPS_FL_DYNAMIC. It causes that
unregister_ftrace_function() calls:
* schedule_on_each_cpu(ftrace_sync) - always
* synchronize_rcu_tasks() - in preemptive kernel
The effect is that nobody is neither inside the dynamic trampoline nor inside
the ftrace handler after unregister_ftrace_function() returns.
[[email protected]: reformat changelog, fix comment]
Signed-off-by: Petr Mladek <[email protected]>
Acked-by: Josh Poimboeuf <[email protected]>
Acked-by: Miroslav Benes <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
|
|
Recently vDSO support for CLOCK_MONOTONIC_RAW was added in
49eea433b326 ("arm64: Add support for CLOCK_MONOTONIC_RAW in
clock_gettime() vDSO"). Noticing that the core timekeeping code
never set tkr_raw.xtime_nsec, the vDSO implementation didn't
bother exposing it via the data page and instead took the
unshifted tk->raw_time.tv_nsec value which was then immediately
shifted left in the vDSO code.
Unfortunately, by accellerating the MONOTONIC_RAW clockid, it
uncovered potential 1ns time inconsistencies caused by the
timekeeping core not handing sub-ns resolution.
Now that the core code has been fixed and is actually setting
tkr_raw.xtime_nsec, we need to take that into account in the
vDSO by adding it to the shifted raw_time value, in order to
fix the user-visible inconsistency. Rather than do that at each
use (and expand the data page in the process), instead perform
the shift/addition operation when populating the data page and
remove the shift from the vDSO code entirely.
[jstultz: minor whitespace tweak, tried to improve commit
message to make it more clear this fixes a regression]
Reported-by: John Stultz <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: John Stultz <[email protected]>
Tested-by: Daniel Mentz <[email protected]>
Acked-by: Kevin Brodsky <[email protected]>
Cc: Prarit Bhargava <[email protected]>
Cc: Richard Cochran <[email protected]>
Cc: Stephen Boyd <[email protected]>
Cc: "stable #4 . 8+" <[email protected]>
Cc: Miroslav Lichvar <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
Due to how the MONOTONIC_RAW accumulation logic was handled,
there is the potential for a 1ns discontinuity when we do
accumulations. This small discontinuity has for the most part
gone un-noticed, but since ARM64 enabled CLOCK_MONOTONIC_RAW
in their vDSO clock_gettime implementation, we've seen failures
with the inconsistency-check test in kselftest.
This patch addresses the issue by using the same sub-ns
accumulation handling that CLOCK_MONOTONIC uses, which avoids
the issue for in-kernel users.
Since the ARM64 vDSO implementation has its own clock_gettime
calculation logic, this patch reduces the frequency of errors,
but failures are still seen. The ARM64 vDSO will need to be
updated to include the sub-nanosecond xtime_nsec values in its
calculation for this issue to be completely fixed.
Signed-off-by: John Stultz <[email protected]>
Tested-by: Daniel Mentz <[email protected]>
Cc: Prarit Bhargava <[email protected]>
Cc: Kevin Brodsky <[email protected]>
Cc: Richard Cochran <[email protected]>
Cc: Stephen Boyd <[email protected]>
Cc: Will Deacon <[email protected]>
Cc: "stable #4 . 8+" <[email protected]>
Cc: Miroslav Lichvar <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
In tests, which excercise switching of clocksources, a NULL
pointer dereference can be observed on AMR64 platforms in the
clocksource read() function:
u64 clocksource_mmio_readl_down(struct clocksource *c)
{
return ~(u64)readl_relaxed(to_mmio_clksrc(c)->reg) & c->mask;
}
This is called from the core timekeeping code via:
cycle_now = tkr->read(tkr->clock);
tkr->read is the cached tkr->clock->read() function pointer.
When the clocksource is changed then tkr->clock and tkr->read
are updated sequentially. The code above results in a sequential
load operation of tkr->read and tkr->clock as well.
If the store to tkr->clock hits between the loads of tkr->read
and tkr->clock, then the old read() function is called with the
new clock pointer. As a consequence the read() function
dereferences a different data structure and the resulting 'reg'
pointer can point anywhere including NULL.
This problem was introduced when the timekeeping code was
switched over to use struct tk_read_base. Before that, it was
theoretically possible as well when the compiler decided to
reload clock in the code sequence:
now = tk->clock->read(tk->clock);
Add a helper function which avoids the issue by reading
tk_read_base->clock once into a local variable clk and then issue
the read function via clk->read(clk). This guarantees that the
read() function always gets the proper clocksource pointer handed
in.
Since there is now no use for the tkr.read pointer, this patch
also removes it, and to address stopping the fast timekeeper
during suspend/resume, it introduces a dummy clocksource to use
rather then just a dummy read function.
Signed-off-by: John Stultz <[email protected]>
Acked-by: Ingo Molnar <[email protected]>
Cc: Prarit Bhargava <[email protected]>
Cc: Richard Cochran <[email protected]>
Cc: Stephen Boyd <[email protected]>
Cc: stable <[email protected]>
Cc: Miroslav Lichvar <[email protected]>
Cc: Daniel Mentz <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
Setting these bits causes libinput to fail to initialize the device;
setting BTN_TOUCH and BTN_TOOL_FINGER causes it to treat the mouse as a
touchpad, and it then refuses to continue when it discovers ABS_X is not
set.
This breaks all known Wayland compositors, as well as Xorg when the
libinput driver is being used.
This reverts commit f4b65b9563216b3e01a5cc844c3ba68901d9b195.
Signed-off-by: Daniel Stone <[email protected]>
Cc: Che-Liang Chiou <[email protected]>
Cc: Thierry Escande <[email protected]>
Cc: Jiri Kosina <[email protected]>
Cc: Benjamin Tissoires <[email protected]>
Acked-by: Benjamin Tissoires <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
|
|
Broxton-T was a forgotten child and we didn't apply the quirks for
Skylake+ properly. Meanwhile, a quirk for reducing the DMA latency
seems specific to the early Broxton model, so we leave as is.
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Without this quirk, the touchpad is not responsive on this product, with
the following message repeated in the logs:
psmouse serio1: bad data from KBC - timeout
Add it to the notimeout list alongside other similar Fujitsu laptops.
Signed-off-by: Daniel Drake <[email protected]>
Cc: [email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One build fix for an Amlogic clk driver and a handful of Allwinner clk
driver fixes for some DT bindings and a randconfig build error that
all came in this merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: a64: Export PLL_PERIPH0 clock for the PRCM
clk: sunxi-ng: h3: Export PLL_PERIPH0 clock for the PRCM
dt-bindings: clock: sunxi-ccu: Add pll-periph to PRCM's needed clocks
clk: sunxi-ng: sun5i: Fix ahb_bist_clk definition
clk: sunxi-ng: enable SUNXI_CCU_MP for PRCM
clk: meson: gxbb: fix build error without RESET_CONTROLLER
clk: sunxi-ng: v3s: Fix usb otg device reset bit
clk: sunxi-ng: a31: Correct lcd1-ch1 clock register offset
|
|
Pull NTB fixes from Jon Mason:
"NTB bug fixes to address the modinfo in ntb_perf, a couple of bugs in
the NTB transport QP calculations, skx doorbells, and sleeping in
ntb_async_tx_submit"
* tag 'ntb-4.12-bugfixes' of git://github.com/jonmason/ntb:
ntb: no sleep in ntb_async_tx_submit
ntb: ntb_hw_intel: Skylake doorbells should be 32bits, not 64bits
ntb_transport: fix bug calculating num_qps_mw
ntb_transport: fix qp count bug
NTB: ntb_test: fix bug printing ntb_perf results
ntb: Correct modinfo usage statement for ntb_perf
|
|
Signed-off-by: Manish Rangankar <[email protected]>
Reviewed-by: Lee Duncan <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Signed-off-by: Manish Rangankar <[email protected]>
Reviewed-by: Lee Duncan <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Odd versions of gcc for the sh4 architecture will actually warn about
flags being used while uninitialized, so we set them to zero. Non crazy
gccs will optimize that out again, so it doesn't make a difference.
Next, over aggressive gccs could inline the expression that defines
use_lock, which could then introduce a race resulting in a lock
imbalance. By using READ_ONCE, we prevent that fate. Finally, we make
that assignment const, so that gcc can still optimize a nice amount.
Finally, we fix a potential deadlock between primary_crng.lock and
batched_entropy_reset_lock, where they could be called in opposite
order. Moving the call to invalidate_batched_entropy to outside the lock
rectifies this issue.
Fixes: b169c13de473a85b3c859bb36216a4cb5f00a54a
Signed-off-by: Jason A. Donenfeld <[email protected]>
Signed-off-by: Theodore Ts'o <[email protected]>
Cc: [email protected]
|
|
into drm-next
A few more things for 4.13:
- Semaphore support using sync objects
- Drop fb location programming
- Optimize bo list ioctl
* 'drm-next-4.13' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Optimize mutex usage (v4)
drm/amdgpu: Optimization of AMDGPU_BO_LIST_OP_CREATE (v2)
amdgpu: use drm sync objects for shared semaphores (v6)
amdgpu/cs: split out fence dependency checking (v2)
drm/amdgpu: don't check the default value for vm size
|
|
drm-next
Here are the Mali DP driver changes. They include the mali-dp specific
changes from Jose Abreu on crtc->mode_valid() as well as a couple of
patches for fixing the sharing of IRQ lines and use of DRM CMA helper
for framebuffer physical address calculation. Please pull!
* 'for-upstream/mali-dp' of git://linux-arm.org/linux-ld:
drm/arm: mali-dp: Use CMA helper for plane buffer address calculation
drm/mali-dp: Check PM status when sharing interrupt lines
drm/arm: malidp: Use crtc->mode_valid() callback
|
|
- HDMI stereoscopic support
- Rework of display code to properly support SOR pad macro routing on
>=GM20x GPUs
- Various other fixes/improvements.
* 'linux-4.13' of git://github.com/skeggsb/linux: (73 commits)
drm/nouveau/disp/nv50-: avoid creating ORs that aren't present on HW
drm/nouveau: use proper prototype in nouveau_pmops_runtime() definition
drm/nouveau: Skip vga_fini on non-PCI device
drm/nouveau/tegra: Don't leave GPU in reset
drm/nouveau/tegra: Skip manual unpowergating when not necessary
drm/nouveau/hwmon: Change permissions to numeric
drm/nouveau/hwmon: expose the auto_point and pwm_min/max attrs
drm/nouveau/hwmon: Remove old code, add .write/.read operations
drm/nouveau/hwmon: Add nouveau_hwmon_ops structure with .is_visible/.read_string
drm/nouveau/hwmon: Add config for all sensors and their settings
drm/nouveau/disp/gm200-: allow non-identity mapping of SOR <-> macro links
drm/nouveau/disp/nv50-: implement a common supervisor 3.0
drm/nouveau/disp/nv50-: implement a common supervisor 2.2
drm/nouveau/disp/nv50-: implement a common supervisor 2.1
drm/nouveau/disp/nv50-: implement a common supervisor 2.0
drm/nouveau/disp/nv50-: implement a common supervisor 1.0
drm/nouveau/disp/nv50-gt21x: remove workaround for dp->tmds hotplug issues
drm/nouveau/disp/dp: use new devinit script interpreter entry-point
drm/nouveau/disp/dp: determine link bandwidth requirements from head state
drm/nouveau/disp: introduce acquire/release display path methods
...
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.13-rc1
This starts off with the addition of more documentation for the host1x
and DRM drivers and finishes with a slew of fixes and enhancements for
the staging IOCTLs as a result of the awesome work done by Dmitry and
Erik on the grate reverse-engineering effort.
* tag 'drm/tegra/for-4.13-rc1' of git://anongit.freedesktop.org/tegra/linux:
gpu: host1x: At first try a non-blocking allocation for the gather copy
gpu: host1x: Refactor channel allocation code
gpu: host1x: Remove unused host1x_cdma_stop() definition
gpu: host1x: Remove unused 'struct host1x_cmdbuf'
gpu: host1x: Check waits in the firewall
gpu: host1x: Correct swapped arguments in the is_addr_reg() definition
gpu: host1x: Forbid unrelated SETCLASS opcode in the firewall
gpu: host1x: Forbid RESTART opcode in the firewall
gpu: host1x: Forbid relocation address shifting in the firewall
gpu: host1x: Do not leak BO's phys address to userspace
gpu: host1x: Correct host1x_job_pin() error handling
gpu: host1x: Initialize firewall class to the job's one
drm/tegra: dc: Disable plane if it is invisible
drm/tegra: dc: Apply clipping to the plane
drm/tegra: dc: Avoid reset asserts on Tegra20
drm/tegra: Check syncpoint ID in the 'submit' IOCTL
drm/tegra: Correct copying of waitchecks and disable them in the 'submit' IOCTL
drm/tegra: Check for malformed offsets and sizes in the 'submit' IOCTL
drm/tegra: Add driver documentation
gpu: host1x: Flesh out kerneldoc
|
|
In function submit_create, if nr_cmds or nr_bos is assigned with
negative value, the allocated buffer may be small than intended.
Using this buffer will lead to buffer overflow issue.
Signed-off-by: Kasin Li <[email protected]>
Signed-off-by: Jordan Crouse <[email protected]>
Signed-off-by: Rob Clark <[email protected]>
|
|
In original function amdgpu_bo_list_get, the waiting
for result->lock can be quite long while mutex
bo_list_lock was holding. It can make other tasks
waiting for bo_list_lock for long period.
Secondly, this patch allows several tasks(readers of idr)
to proceed at the same time.
v2: use rcu and kref (Dave Airlie and Christian König)
v3: update v1 commit message (Michel Dänzer)
v4: rebase on upstream (Alex Deucher)
Signed-off-by: Alex Xie <[email protected]>
Reviewed-by: Christian König <[email protected]>
|
|
v2: Remove duplication of zeroing of bo list (Christian König)
Move idr_alloc function to end of ioctl (Christian König)
Call kfree bo_list when amdgpu_bo_list_set return error.
Combine the previous two patches into this patch.
Add amdgpu_bo_list_set function prototype.
Signed-off-by: Alex Xie <[email protected]>
Reviewed-by: Christian König <[email protected]>
|
|
Signed-off-by: Junshan Fang <[email protected]>
Reviewed-by: Roger.He <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
Signed-off-by: Alex Deucher <[email protected]>
|
|
Maarten and Ville noticed that we are enabling backlight via DP aux very
early in the modeset_init path via the intel_dp_aux_setup_backlight()
function, since commit e7156c833903 ("drm/i915: Add Backlight Control using
DPCD for eDP connectors (v9)"). Looks like all we need to do during
_setup_backlight() is read the current brightness state instead of
modifying it.
v2: Rewrote commit message.
Cc: Ville Syrjala <[email protected]>
Cc: Maarten Lankhorst <[email protected]>
Cc: Jani Nikula <[email protected]>
Cc: Yetunde Adebisi <[email protected]>
Signed-off-by: Dhinakaran Pandiyan <[email protected]>
Reviewed-by: Maarten Lankhorst <[email protected]>
Acked-by: Jani Nikula <[email protected]>
Tested-by: Puthikorn Voravootivat <[email protected]>
Fixes: e7156c833903 ("drm/i915: Add Backlight Control using DPCD for eDP connectors (v9)")
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Ville Syrjälä <[email protected]>
(cherry picked from commit f6262bda462e81e959b80a96dac799bd9df27f73)
Signed-off-by: Jani Nikula <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Now before dumping a sock in sctp_diag, it only holds the sock while
the ep may be already destroyed. It can cause a use-after-free panic
when accessing ep->asocs.
This patch is to set sctp_sk(sk)->ep NULL in sctp_endpoint_destroy,
and check if this ep is already destroyed before dumping this ep.
Suggested-by: Marcelo Ricardo Leitner <[email protected]>
Signed-off-by: Xin Long <[email protected]>
Acked-by: Neil Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Do not sleep in ntb_async_tx_submit, which could deadlock.
This reverts commit "8c874cc140d667f84ae4642bb5b5e0d6396d2ca4"
Fixes: 8c874cc140d6 ("NTB: Address out of DMA descriptor issue with NTB")
Reported-by: Jia-Ju Bai <[email protected]>
Signed-off-by: Allen Hubbe <[email protected]>
Acked-by: Dave Jiang <[email protected]>
Signed-off-by: Jon Mason <[email protected]>
|
|
Fixing doorbell register length to 32bits per spec. On Skylake NTB, the
doorbell registers are 32bit write only registers. The source for the
doorbell is a 64bit register that shows the interrupt bits.
Signed-off-by: Dave Jiang <[email protected]>
Fixes: 783dfa6cc41b ("ntb: Adding Skylake Xeon NTB support")
Acked-by: Allen Hubbe <[email protected]>
Signed-off-by: Jon Mason <[email protected]>
|
|
A divide by zero error occurs if qp_count is less than mw_count because
num_qps_mw is calculated to be zero. The calculation appears to be
incorrect.
The requirement is for num_qps_mw to be set to qp_count / mw_count
with any remainder divided among the earlier mws.
For example, if mw_count is 5 and qp_count is 12 then mws 0 and 1
will have 3 qps per window and mws 2 through 4 will have 2 qps per window.
Thus, when mw_num < qp_count % mw_count, num_qps_mw is 1 higher
than when mw_num >= qp_count.
Signed-off-by: Logan Gunthorpe <[email protected]>
Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Acked-by: Allen Hubbe <[email protected]>
Signed-off-by: Jon Mason <[email protected]>
|
|
In cases where there are more mw's than spads/2-2, the mw count gets
reduced to match the limitation. ntb_transport also tries to ensure that
there are fewer qps than mws but uses the full mw count instead of
the reduced one. When this happens, the math in
'ntb_transport_setup_qp_mw' will get confused and result in a kernel
paging request bug.
This patch fixes the bug by reducing qp_count to the reduced mw count
instead of the full mw count.
Signed-off-by: Logan Gunthorpe <[email protected]>
Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Acked-by: Allen Hubbe <[email protected]>
Signed-off-by: Jon Mason <[email protected]>
|
|
The code mistakenly prints the local perf results for the remote test
so the script reports identical results for both directions. Fix this
by ensuring we print the remote result.
Signed-off-by: Logan Gunthorpe <[email protected]>
Fixes: a9c59ef77458 ("ntb_test: Add a selftest script for the NTB subsystem")
Acked-by: Allen Hubbe <[email protected]>
Signed-off-by: Jon Mason <[email protected]>
|
|
The order parameters are powers of 2; adjust the usage information
to use correct mathematical representations.
Signed-off-by: Gary R Hook <[email protected]>
Fixes: 8a7b6a778a85 ("ntb: ntb perf tool")
Acked-by: Dave Jiang <[email protected]>
Signed-off-by: Jon Mason <[email protected]>
|