| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull documentation fixes from Jonathan Corbet:
"The Sphinx 2.0 release contained a few incompatible API changes that
broke our extensions and, thus, the documentation build in general.
Who knew that those deprecation warnings it was outputting actually
meant we should change something? This set of fixes makes the build
work again with Sphinx 2.0 and eliminates the warnings for 1.8. As
part of that, we also need a few fixes to the docs for places where
the new Sphinx is more strict.
It is a bit late in the cycle for this kind of change, but it does fix
problems that people are experiencing now.
There has been some talk of raising the minimum version of Sphinx we
support. I don't want to do that abruptly, though, so these changes
add some glue to continue to support versions back to 1.3. We will be
adding some infrastructure soon to nudge users of old versions
forward, with the idea of maybe increasing our minimum version (and
removing this glue) sometime in the future"
* tag 'docs-5.2-fixes2' of git://git.lwn.net/linux:
drm/i915: Maintain consistent documentation subsection ordering
scripts/sphinx-pre-install: make it handle Sphinx versions
docs: Fix conf.py for Sphinx 2.0
docs: fix multiple doc build warnings in enumeration.rst
lib/list_sort: fix kerneldoc build error
docs: fix numaperf.rst and add it to the doc tree
doc: Cope with the deprecation of AutoReporter
doc: Cope with Sphinx logging deprecations
|
|
Max Uvarov says:
====================
net: phy: dp83867: add some fixes
v3: use phy_modify_mmd()
v2: fix minor comments by Heiner Kallweit and Florian Fainelli
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
PHY_INTERFACE_MODE_RGMII_RXID is less then TXID
so code to set tx delay is never called.
Fixes: 2a10154abcb75 ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Max Uvarov <[email protected]>
Cc: Florian Fainelli <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Phy state machine calls _config_init just after
reset.
Signed-off-by: Max Uvarov <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
After reset SGMII Autoneg timer is set to 2us (bits 6 and 5 are 01).
That is not enough to finalize autonegatiation on some devices.
Increase this timer duration to maximum supported 16ms.
Signed-off-by: Max Uvarov <[email protected]>
Cc: Heiner Kallweit <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
For supporting 10Mps speed in SGMII mode DP83867_10M_SGMII_RATE_ADAPT bit
of DP83867_10M_SGMII_CFG register has to be cleared by software.
That does not affect speeds 100 and 1000 so can be done on init.
Signed-off-by: Max Uvarov <[email protected]>
Cc: Heiner Kallweit <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected. Warn the user when the
PHY fails to boot the firmware and refuse to initialise.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <[email protected]>
Tested-by: Maxime Chevallier <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call. This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.
Signed-off-by: Russell King <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If blk_mq_init_allocated_queue() fails, make sure to free the poll
stat callback struct allocated.
Signed-off-by: Jes Sorensen <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Fix the following sparse context imbalance regression introduced in
a patch that fixed sleeping function called from invalid context bug.
kbuild test robot reported on:
tree/branch: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-linus
Regressions in current branch:
drivers/usb/usbip/stub_dev.c:399:9: sparse: sparse: context imbalance in 'stub_probe' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:418:13: sparse: sparse: context imbalance in 'stub_disconnect' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:464:1-10: second lock on line 476
Error ids grouped by kconfigs:
recent_errors
├── i386-allmodconfig
│ └── drivers-usb-usbip-stub_dev.c:second-lock-on-line
├── x86_64-allmodconfig
│ ├── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_disconnect-different-lock-contexts-for-basic-block
│ └── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_probe-different-lock-contexts-for-basic-block
└── x86_64-allyesconfig
└── drivers-usb-usbip-stub_dev.c:second-lock-on-line
This is a real problem in an error leg where spin_lock() is called on an
already held lock.
Fix the imbalance in stub_probe() and stub_disconnect().
Signed-off-by: Shuah Khan <[email protected]>
Fixes: 0c9e8b3cad65 ("usbip: usbip_host: fix BUG: sleeping function called from invalid context")
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The sh_eth_close() resets the MAC and then calls phy_stop()
so that mdio read access result is incorrect without any error
according to kernel trace like below:
ifconfig-216 [003] .n.. 109.133124: mdio_access: ee700000.ethernet-ffffffff read phy:0x01 reg:0x00 val:0xffff
According to the hardware manual, the RMII mode should be set to 1
before operation the Ethernet MAC. However, the previous code was not
set to 1 after the driver issued the soft_reset in sh_eth_dev_exit()
so that the mdio read access result seemed incorrect. To fix the issue,
this patch adds a condition and set the RMII mode register in
sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs.
Note that when I have tried to move the sh_eth_dev_exit() calling
after phy_stop() on sh_eth_close(), but it gets worse (kernel panic
happened and it seems that a register is accessed while the clock is
off).
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- Alexandre Belloni's fixes to rtc regressions introduced in kselftest
Makefile test run output refactoring work from Kees Cook.
- ftrace test checkbashisms fixes from Masami Hiramatsu
* tag 'linux-kselftest-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: rtc: rtctest: specify timeouts
selftests/harness: Allow test to configure timeout
selftests/ftrace: Add checkbashisms meta-testcase
selftests/ftrace: Make a script checkbashisms clean
|
|
This patch fixes a complain about possible sleep during
spinlock aquired
"BUG: sleeping function called from invalid context at
include/crypto/algapi.h:426"
for the ctr(aes) and ctr(des) s390 specific ciphers.
Instead of using a spinlock this patch introduces a mutex
which is save to be held in sleeping context. Please note
a deadlock is not possible as mutex_trylock() is used.
Signed-off-by: Harald Freudenberger <[email protected]>
Reported-by: Julian Wiedmann <[email protected]>
Cc: [email protected]
Signed-off-by: Heiko Carstens <[email protected]>
|
|
In cifs_read_allocate_pages, in case of ENOMEM, we go through
whole rdata->pages array but we have failed the allocation before
nr_pages, therefore we may end up calling put_page with NULL
pointer, causing oops
Signed-off-by: Roberto Bergantinos Corpas <[email protected]>
Acked-by: Pavel Shilovsky <[email protected]>
Signed-off-by: Steve French <[email protected]>
CC: Stable <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"This fixes a memory leak from the error path in the event filter
logic"
* tag 'trace-v5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Avoid memory leak in predicate_parse()
|
|
MAYEXEC test was mistakenly added, remove it. Checking MAYEXEC in the
driver prevents it from working with userspace that uses things like EXEC
STACK. (ie some Fortran and other runtimes)
Fixes: 40909f664d27 ("RDMA/efa: Add EFA verbs implementation")
Reported-by: Jason Gunthorpe <[email protected]>
Reviewed-by: Firas JahJah <[email protected]>
Reviewed-by: Yossi Leybovich <[email protected]>
Signed-off-by: Gal Pressman <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
Commit 25c13324d03d ("IB/mlx5: Add steering SW ICM device memory type")
breaks i386 build by introducing three 64-bit divisions. As the divisor is
MLX5_SW_ICM_BLOCK_SIZE() which is always a power of 2, we can replace the
division with bit operations.
Fixes: 25c13324d03d ("IB/mlx5: Add steering SW ICM device memory type")
Signed-off-by: Michal Kubecek <[email protected]>
Reviewed-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
User applications can register memory regions for TID buffers that are not
aligned on page boundaries. Hfi1 is expected to pin those pages in memory
and cache the pages with mmu_rb. The rb tree will fail to insert pages
that are not aligned correctly.
Validate whether a given virtual address is page aligned before pinning.
Fixes: 7e7a436ecb6e ("staging/hfi1: Add TID entry program function body")
Reviewed-by: Michael J. Ruhl <[email protected]>
Signed-off-by: Kamenee Arumugam <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
The command 'ibv_devinfo -v' reports 0 for max_mr.
Fix by assigning the query values after the mr lkey_table has been built
rather than early on in the driver.
Fixes: 7b1e2099adc8 ("IB/rdmavt: Move memory registration into rdmavt")
Reviewed-by: Josh Collier <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
By code inspection, the freeze_work is never canceled.
Fix by adding a cancel_work_sync in the shutdown path to insure it is no
longer running.
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Michael J. Ruhl <[email protected]>
Reviewed-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
The qpn allocation logic has a WARN_ON() that intends to detect the use of
an index that will introduce bits in the lower order bits of the QOS bits
in the QPN.
Unfortunately, it has the following bugs:
- it misfires when wrapping QPN allocation for non-QOS
- it doesn't correctly detect low order QOS bits (despite the comment)
The WARN_ON() should not be applied to non-QOS (qos_shift == 1).
Additionally, it SHOULD test the qpn bits per the table below:
2 data VLs: [qp7, qp6, qp5, qp4, qp3, qp2, qp1] ^
[ 0, 0, 0, 0, 0, 0, sc0], qp bit 1 always 0*
3-4 data VLs: [qp7, qp6, qp5, qp4, qp3, qp2, qp1] ^
[ 0, 0, 0, 0, 0, sc1, sc0], qp bits [21] always 0
5-8 data VLs: [qp7, qp6, qp5, qp4, qp3, qp2, qp1] ^
[ 0, 0, 0, 0, sc2, sc1, sc0] qp bits [321] always 0
Fix by qualifying the warning for qos_shift > 1 and producing the correct
mask to insure the above bits are zero without generating a superfluous
warning.
Fixes: 501edc42446e ("IB/rdmavt: Correct warning during QPN allocation")
Reviewed-by: Kaike Wan <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
to avoid screen corruption during modprobe.
Signed-off-by: Flora Cui <[email protected]>
Reviewed-by: Huang Rui <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Calling sys_ni_syscall through a syscall_fn_t pointer trips indirect
call Control-Flow Integrity checking due to a function type
mismatch. Use SYSCALL_DEFINE0 for __arm64_sys_ni_syscall instead and
remove the now unnecessary casts.
Signed-off-by: Sami Tolvanen <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
Although a syscall defined using SYSCALL_DEFINE0 doesn't accept
parameters, use the correct function type to avoid indirect call
type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
Syscall wrappers in <asm/syscall_wrapper.h> use const struct pt_regs *
as the argument type. Use const in syscall_fn_t as well to fix indirect
call type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <[email protected]>
Reviewed-by: Mark Rutland <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
Now a063057d7c73 ("block: Fix a race between request queue removal and
the block cgroup controller") has been reverted, and blkcg_exit_queue()
won't be called in blk_cleanup_queue() any more.
So don't need to protect generic_make_request_checks() with
blk_queue_enter(), then the total mess can be cleaned.
37f9579f4c31 ("blk-mq: Avoid that submitting a bio concurrently with device
removal triggers a crash") is reverted.
Cc: Bart Van Assche <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Ming Lei <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Commit 498f6650aec8 ("block: Fix a race between the cgroup code and
request queue initialization") moves what blk_exit_queue does into
blk_cleanup_queue() for fixing issue caused by changing back
queue lock.
However, after legacy request IO path is killed, driver queue lock
won't be used at all, and there isn't story for changing back
queue lock. Then the issue addressed by Commit 498f6650aec8 doesn't
exist any more.
So move move blk_exit_queue into __blk_release_queue.
This patch basically reverts the following two commits:
498f6650aec8 block: Fix a race between the cgroup code and request queue initialization
24ecc3585348 block: Ensure that a request queue is dissociated from the cgroup controller
Cc: Bart Van Assche <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Ming Lei <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Overlapping overlay layers are not supported and can cause unexpected
behavior, but overlayfs does not currently check or warn about these
configurations.
User is not supposed to specify the same directory for upper and
lower dirs or for different lower layers and user is not supposed to
specify directories that are descendants of each other for overlay
layers, but that is exactly what this zysbot repro did:
https://syzkaller.appspot.com/x/repro.syz?x=12c7a94f400000
Moving layer root directories into other layers while overlayfs
is mounted could also result in unexpected behavior.
This commit places "traps" in the overlay inode hash table.
Those traps are dummy overlay inodes that are hashed by the layers
root inodes.
On mount, the hash table trap entries are used to verify that overlay
layers are not overlapping. While at it, we also verify that overlay
layers are not overlapping with directories "in-use" by other overlay
instances as upperdir/workdir.
On lookup, the trap entries are used to verify that overlay layers
root inodes have not been moved into other layers after mount.
Some examples:
$ ./run --ov --samefs -s
...
( mkdir -p base/upper/0/u base/upper/0/w base/lower lower upper mnt
mount -o bind base/lower lower
mount -o bind base/upper upper
mount -t overlay none mnt ...
-o lowerdir=lower,upperdir=upper/0/u,workdir=upper/0/w)
$ umount mnt
$ mount -t overlay none mnt ...
-o lowerdir=base,upperdir=upper/0/u,workdir=upper/0/w
[ 94.434900] overlayfs: overlapping upperdir path
mount: mount overlay on mnt failed: Too many levels of symbolic links
$ mount -t overlay none mnt ...
-o lowerdir=upper/0/u,upperdir=upper/0/u,workdir=upper/0/w
[ 151.350132] overlayfs: conflicting lowerdir path
mount: none is already mounted or mnt busy
$ mount -t overlay none mnt ...
-o lowerdir=lower:lower/a,upperdir=upper/0/u,workdir=upper/0/w
[ 201.205045] overlayfs: overlapping lowerdir path
mount: mount overlay on mnt failed: Too many levels of symbolic links
$ mount -t overlay none mnt ...
-o lowerdir=lower,upperdir=upper/0/u,workdir=upper/0/w
$ mv base/upper/0/ base/lower/
$ find mnt/0
mnt/0
mnt/0/w
find: 'mnt/0/w/work': Too many levels of symbolic links
find: 'mnt/0/u': Too many levels of symbolic links
Reported-by: [email protected]
Signed-off-by: Amir Goldstein <[email protected]>
Signed-off-by: Miklos Szeredi <[email protected]>
|
|
With gcc 4.1:
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_switch_fetching_mode’:
sound/firewire/fireface/ff-protocol-latter.c:97: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_begin_session’:
sound/firewire/fireface/ff-protocol-latter.c:170: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:197: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:205: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_finish_session’:
sound/firewire/fireface/ff-protocol-latter.c:214: warning: integer constant is too large for ‘long’ type
Fix this by adding the missing "ULL" suffixes.
Add the same suffix to the last constant, to maintain consistency.
Fixes: fd1cc9de64c2ca6c ("ALSA: fireface: add support for Fireface UCX")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Takashi Sakamoto <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
I don't think this is userspace visible but SIGKILL does not have
any si_codes that use the fault member of the siginfo union. Correct
this the simple way and call force_sig instead of force_sig_fault when
the signal is SIGKILL.
The two know places where synchronous SIGKILL are generated are
do_bad_area and fpsimd_save. The call paths to force_sig_fault are:
do_bad_area
arm64_force_sig_fault
force_sig_fault
force_signal_inject
arm64_notify_die
arm64_force_sig_fault
force_sig_fault
Which means correcting this in arm64_force_sig_fault is enough
to ensure the arm64 code is not misusing the generic code, which
could lead to maintenance problems later.
Cc: [email protected]
Cc: Dave Martin <[email protected]>
Cc: James Morse <[email protected]>
Cc: Will Deacon <[email protected]>
Fixes: af40ff687bc9 ("arm64: signal: Ensure si_code is valid for all fault signals")
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
We met another Acer Aspire laptop which has the problem on the
headset-mic, the Pin 0x19 is not set the corret configuration for a
mic and the pin presence can't be detected too after plugging a
headset. Kailang suggested that we should set the coeff to enable the
mic and apply the ALC269_FIXUP_LIFEBOOK_EXTMIC. After doing that,
both headset-mic presence and headset-mic work well.
The existing ALC255_FIXUP_ACER_MIC_NO_PRESENCE set the headset-mic
jack to be a phantom jack. Now since the jack can support presence
unsol event, let us imporve it to set the jack to be a normal jack.
https://bugs.launchpad.net/bugs/1821269
Fixes: 5824ce8de7b1c ("ALSA: hda/realtek - Add support for Acer Aspire E5-475 headset mic")
Cc: Chris Chiu <[email protected]>
CC: Daniel Drake <[email protected]>
Cc: <[email protected]>
Signed-off-by: Kailang Yang <[email protected]>
Signed-off-by: Hui Wang <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
When a vCPU is connected to the KVM device, it is done using its vCPU
identifier in the guest. Fix the enforced limit on the vCPU identifier
by taking into account the SMT mode.
Reported-by: Satheesh Rajendran <[email protected]>
Tested-by: Satheesh Rajendran <[email protected]>
Signed-off-by: Cédric Le Goater <[email protected]>
Reviewed-by: Greg Kurz <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
When a CPU is hot-unplugged, the EQ is deconfigured using a zero size
and a zero address. In this case, there is no need to check the flag
and queue size validity. Move the checks after the queue reset code
section to fix CPU hot-unplug.
Reported-by: Satheesh Rajendran <[email protected]>
Tested-by: Satheesh Rajendran <[email protected]>
Signed-off-by: Cédric Le Goater <[email protected]>
Reviewed-by: Greg Kurz <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Improve the release of the XIVE KVM device by clearing the file
address_space, which is used to unmap the interrupt ESB pages when a
device is passed-through.
Suggested-by: Paul Mackerras <[email protected]>
Signed-off-by: Cédric Le Goater <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Currently the HV KVM code takes the kvm->lock around calls to
kvm_for_each_vcpu() and kvm_get_vcpu_by_id() (which can call
kvm_for_each_vcpu() internally). However, that leads to a lock
order inversion problem, because these are called in contexts where
the vcpu mutex is held, but the vcpu mutexes nest within kvm->lock
according to Documentation/virtual/kvm/locking.txt. Hence there
is a possibility of deadlock.
To fix this, we simply don't take the kvm->lock mutex around these
calls. This is safe because the implementations of kvm_for_each_vcpu()
and kvm_get_vcpu_by_id() have been designed to be able to be called
locklessly.
Signed-off-by: Paul Mackerras <[email protected]>
Reviewed-by: Cédric Le Goater <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Currently the Book 3S KVM code uses kvm->lock to synchronize access
to the kvm->arch.rtas_tokens list. Because this list is scanned
inside kvmppc_rtas_hcall(), which is called with the vcpu mutex held,
taking kvm->lock cause a lock inversion problem, which could lead to
a deadlock.
To fix this, we add a new mutex, kvm->arch.rtas_token_lock, which nests
inside the vcpu mutexes, and use that instead of kvm->lock when
accessing the rtas token list.
This removes the lockdep_assert_held() in kvmppc_rtas_tokens_free().
At this point we don't hold the new mutex, but that is OK because
kvmppc_rtas_tokens_free() is only called when the whole VM is being
destroyed, and at that point nothing can be looking up a token in
the list.
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Currently the HV KVM code uses kvm->lock in conjunction with a flag,
kvm->arch.mmu_ready, to synchronize MMU setup and hold off vcpu
execution until the MMU-related data structures are ready. However,
this means that kvm->lock is being taken inside vcpu->mutex, which
is contrary to Documentation/virtual/kvm/locking.txt and results in
lockdep warnings.
To fix this, we add a new mutex, kvm->arch.mmu_setup_lock, which nests
inside the vcpu mutexes, and is taken in the places where kvm->lock
was taken that are related to MMU setup.
Additionally we take the new mutex in the vcpu creation code at the
point where we are creating a new vcore, in order to provide mutual
exclusion with kvmppc_update_lpcr() and ensure that an update to
kvm->arch.lpcr doesn't get missed, which could otherwise lead to a
stale vcore->lpcr value.
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Currently, kvmppc_xive_release() and kvmppc_xive_native_release() clear
kvm->arch.mmu_ready and call kick_all_cpus_sync() as a way of ensuring
that no vcpus are executing in the guest. However, future patches will
change the mutex associated with kvm->arch.mmu_ready to a new mutex that
nests inside the vcpu mutexes, making it difficult to continue to use
this method.
In fact, taking the vcpu mutex for a vcpu excludes execution of that
vcpu, and we already take the vcpu mutex around the call to
kvmppc_xive_[native_]cleanup_vcpu(). Once the cleanup function is
done and we release the vcpu mutex, the vcpu can execute once again,
but because we have cleared vcpu->arch.xive_vcpu, vcpu->arch.irq_type,
vcpu->arch.xive_esc_vaddr and vcpu->arch.xive_esc_raddr, that vcpu will
not be going into XIVE code any more. Thus, once we have cleaned up
all of the vcpus, we are safe to clean up the rest of the XIVE state,
and we don't need to use kvm->arch.mmu_ready to hold off vcpu execution.
Signed-off-by: Paul Mackerras <[email protected]>
|
|
enabled"
This reverts commit 3e6a8fb3308419129c7a52de6eb42feef5a919a0.
Cc: Andy Gross <[email protected]>
Cc: David Brown <[email protected]>
Cc: Amit Kucheria <[email protected]>
Cc: Zhang Rui <[email protected]>
Cc: Daniel Lezcano <[email protected]>
Suggested-by: Amit Kucheria <[email protected]>
Reported-by: Andy Gross <[email protected]>
Signed-off-by: Eduardo Valentin <[email protected]>
|
|
When CQE compression is enabled (Multi-host systems), compressed CQEs
might arrive to the driver rx, compressed CQEs don't have a valid hash
offload and the driver already reports a hash value of 0 and invalid hash
type on the skb for compressed CQEs, but this is not good enough.
On a congested PCIe, where CQE compression will kick in aggressively,
gro will deliver lots of out of order packets due to the invalid hash
and this might cause a serious performance drop.
The only valid solution, is to disable rxhash offload at all when CQE
compression is favorable (Multi-host systems).
Fixes: 7219ab34f184 ("net/mlx5e: CQE compression")
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
When register indr block for vlan device, it should check the real_dev
of vlan device is same as uplink device. Or it will set offload rule
to mlx5e which will never hit.
Fixes: 35a605db168c ("net/mlx5e: Offload TC e-switch rules with ingress VLAN device")
Signed-off-by: wenxu <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
root ns is yet another fs core node which is freed using kfree() by
tree_put_node().
Rest of the other fs core objects are also allocated using kmalloc
variants.
However, root ns memory is allocated using kvzalloc().
Hence allocate root ns memory using kzalloc().
Fixes: 2530236303d9e ("net/mlx5_core: Flow steering tree initialization")
Signed-off-by: Parav Pandit <[email protected]>
Reviewed-by: Daniel Jurgens <[email protected]>
Reviewed-by: Mark Bloch <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
In below code flow, for ingress acl table root ns memory leads
to double free.
mlx5_init_fs
init_ingress_acls_root_ns()
init_ingress_acl_root_ns
kfree(steering->esw_ingress_root_ns);
/* steering->esw_ingress_root_ns is not marked NULL */
mlx5_cleanup_fs
cleanup_ingress_acls_root_ns
steering->esw_ingress_root_ns non NULL check passes.
kfree(steering->esw_ingress_root_ns);
/* double free */
Similar issue exist for other tables.
Hence zero out the pointers to not process the table again.
Fixes: 9b93ab981e3bf ("net/mlx5: Separate ingress/egress namespaces for each vport")
Fixes: 40c3eebb49e51 ("net/mlx5: Add support in RDMA RX steering")
Signed-off-by: Parav Pandit <[email protected]>
Reviewed-by: Mark Bloch <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
When root ns setup for rdma, sniffer tx and sniffer rx fails,
such root ns cleanup is done by the error unwinding path of
mlx5_cleanup_fs().
Below call graph shows an example for sniffer_rx_root_ns.
mlx5_init_fs()
init_sniffer_rx_root_ns()
cleanup_root_ns(steering->sniffer_rx_root_ns);
mlx5_cleanup_fs()
cleanup_root_ns(steering->sniffer_rx_root_ns);
/* double free of sniffer_rx_root_ns */
Hence, use the existing cleanup_fs to cleanup.
Fixes: d83eb50e29de3 ("net/mlx5: Add support in RDMA RX steering")
Fixes: 87d22483ce68e ("net/mlx5: Add sniffer namespaces")
Signed-off-by: Parav Pandit <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
In case mlx5_core_set_hca_defaults fails, it should jump to
mlx5_cleanup_fs, fix that.
Fixes: c85023e153e3 ("IB/mlx5: Add raw ethernet local loopback support")
Signed-off-by: Saeed Mahameed <[email protected]>
Reviewed-by: Huy Nguyen <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Both sysfs-bus-mdio and sysfs-class-net-phydev contain the same
duplication information. There is not currently any MDIO bus specific
attribute, but there are PHY device (struct phy_device) specific
attributes. Use the more precise description from sysfs-bus-mdio and
carry that over to sysfs-class-net-phydev.
Fixes: 86f22d04dfb5 ("net: sysfs: Document PHY device sysfs attributes")
Signed-off-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If llc_mac_hdr_init() returns an error, we must drop the skb
since no llc_build_and_send_ui_pkt() caller will take care of this.
BUG: memory leak
unreferenced object 0xffff8881202b6800 (size 2048):
comm "syz-executor907", pid 7074, jiffies 4294943781 (age 8.590s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
1a 00 07 40 00 00 00 00 00 00 00 00 00 00 00 00 ...@............
backtrace:
[<00000000e25b5abe>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
[<00000000e25b5abe>] slab_post_alloc_hook mm/slab.h:439 [inline]
[<00000000e25b5abe>] slab_alloc mm/slab.c:3326 [inline]
[<00000000e25b5abe>] __do_kmalloc mm/slab.c:3658 [inline]
[<00000000e25b5abe>] __kmalloc+0x161/0x2c0 mm/slab.c:3669
[<00000000a1ae188a>] kmalloc include/linux/slab.h:552 [inline]
[<00000000a1ae188a>] sk_prot_alloc+0xd6/0x170 net/core/sock.c:1608
[<00000000ded25bbe>] sk_alloc+0x35/0x2f0 net/core/sock.c:1662
[<000000002ecae075>] llc_sk_alloc+0x35/0x170 net/llc/llc_conn.c:950
[<00000000551f7c47>] llc_ui_create+0x7b/0x140 net/llc/af_llc.c:173
[<0000000029027f0e>] __sock_create+0x164/0x250 net/socket.c:1430
[<000000008bdec225>] sock_create net/socket.c:1481 [inline]
[<000000008bdec225>] __sys_socket+0x69/0x110 net/socket.c:1523
[<00000000b6439228>] __do_sys_socket net/socket.c:1532 [inline]
[<00000000b6439228>] __se_sys_socket net/socket.c:1530 [inline]
[<00000000b6439228>] __x64_sys_socket+0x1e/0x30 net/socket.c:1530
[<00000000cec820c1>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301
[<000000000c32554f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
BUG: memory leak
unreferenced object 0xffff88811d750d00 (size 224):
comm "syz-executor907", pid 7074, jiffies 4294943781 (age 8.600s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 f0 0c 24 81 88 ff ff 00 68 2b 20 81 88 ff ff ...$.....h+ ....
backtrace:
[<0000000053026172>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
[<0000000053026172>] slab_post_alloc_hook mm/slab.h:439 [inline]
[<0000000053026172>] slab_alloc_node mm/slab.c:3269 [inline]
[<0000000053026172>] kmem_cache_alloc_node+0x153/0x2a0 mm/slab.c:3579
[<00000000fa8f3c30>] __alloc_skb+0x6e/0x210 net/core/skbuff.c:198
[<00000000d96fdafb>] alloc_skb include/linux/skbuff.h:1058 [inline]
[<00000000d96fdafb>] alloc_skb_with_frags+0x5f/0x250 net/core/skbuff.c:5327
[<000000000a34a2e7>] sock_alloc_send_pskb+0x269/0x2a0 net/core/sock.c:2225
[<00000000ee39999b>] sock_alloc_send_skb+0x32/0x40 net/core/sock.c:2242
[<00000000e034d810>] llc_ui_sendmsg+0x10a/0x540 net/llc/af_llc.c:933
[<00000000c0bc8445>] sock_sendmsg_nosec net/socket.c:652 [inline]
[<00000000c0bc8445>] sock_sendmsg+0x54/0x70 net/socket.c:671
[<000000003b687167>] __sys_sendto+0x148/0x1f0 net/socket.c:1964
[<00000000922d78d9>] __do_sys_sendto net/socket.c:1976 [inline]
[<00000000922d78d9>] __se_sys_sendto net/socket.c:1972 [inline]
[<00000000922d78d9>] __x64_sys_sendto+0x2a/0x30 net/socket.c:1972
[<00000000cec820c1>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301
[<000000000c32554f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <[email protected]>
Reported-by: syzbot <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In the pmtu_vti6_link_change_mtu test, both local and remote addresses
for the vti6 tunnel are assigned to the same address given to the dummy
interface that we use as encapsulating device with a known MTU.
This works as long as the dummy interface is actually selected, via
rt6_lookup(), as encapsulating device. But if the remote address of the
tunnel is a local address too, the loopback interface could also be
selected, and there's nothing wrong with it.
This is what some older -stable kernels do (3.18.z, at least), and
nothing prevents us from subtly changing FIB implementation to revert
back to that behaviour in the future.
Define an IPv6 prefix instead, and use two separate addresses as local
and remote for vti6, so that the encapsulating device can't be a
loopback interface.
Reported-by: Xiumei Mu <[email protected]>
Fixes: 1fad59ea1c34 ("selftests: pmtu: Add pmtu_vti6_link_change_mtu test")
Signed-off-by: Stefano Brivio <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In flush_cache_ent(), 'ce->ce_path' is allocated by kstrdup_const().
It should be freed by kfree_const(), rather than kfree().
Signed-off-by: Gen Zhang <[email protected]>
Reviewed-by: Paulo Alcantara <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
The 2nd buffer could be NULL even if iov_len is not zero. This can
trigger a panic when handling symlinks. It's easy to reproduce with
LTP fs_racer scripts[1] which are randomly craete/delete/link files
and dirs. Fix this panic by checking if the 2nd buffer is padding
before kfree, like what we do in SMB2_open_free.
[1] https://github.com/linux-test-project/ltp/tree/master/testcases/kernel/fs/racer
Fixes: 2c87d6a94d16 ("cifs: Allocate memory for all iovs in smb2_ioctl")
Signed-off-by: Murphy Zhou <[email protected]>
Signed-off-by: Steve French <[email protected]>
Reviewed-by: Ronnie sahlberg <[email protected]>
|