| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As far as I can tell, the only place the per-cpu ida_bitmap is populated
is in ida_pre_get. The pre-allocated element is stolen in two places in
ida_get_new_above, in both cases immediately followed by a memset(0).
Since ida_get_new_above is called with locks held, do the zeroing in
ida_pre_get, or rather let kmalloc() do it. Also, apparently gcc
generates ~44 bytes of code to do a memset(, 0, 128):
$ scripts/bloat-o-meter vmlinux.{0,1}
add/remove: 0/0 grow/shrink: 2/1 up/down: 5/-88 (-83)
Function old new delta
ida_pre_get 115 119 +4
vermagic 27 28 +1
ida_get_new_above 715 627 -88
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Rasmus Villemoes <[email protected]>
Acked-by: Matthew Wilcox <[email protected]>
Cc: Eric Biggers <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
It was reported by Sergey Senozhatsky that if THP (Transparent Huge
Page) and frontswap (via zswap) are both enabled, when memory goes low
so that swap is triggered, segfault and memory corruption will occur in
random user space applications as follow,
kernel: urxvt[338]: segfault at 20 ip 00007fc08889ae0d sp 00007ffc73a7fc40 error 6 in libc-2.26.so[7fc08881a000+1ae000]
#0 0x00007fc08889ae0d _int_malloc (libc.so.6)
#1 0x00007fc08889c2f3 malloc (libc.so.6)
#2 0x0000560e6004bff7 _Z14rxvt_wcstoutf8PKwi (urxvt)
#3 0x0000560e6005e75c n/a (urxvt)
#4 0x0000560e6007d9f1 _ZN16rxvt_perl_interp6invokeEP9rxvt_term9hook_typez (urxvt)
#5 0x0000560e6003d988 _ZN9rxvt_term9cmd_parseEv (urxvt)
#6 0x0000560e60042804 _ZN9rxvt_term6pty_cbERN2ev2ioEi (urxvt)
#7 0x0000560e6005c10f _Z17ev_invoke_pendingv (urxvt)
#8 0x0000560e6005cb55 ev_run (urxvt)
#9 0x0000560e6003b9b9 main (urxvt)
#10 0x00007fc08883af4a __libc_start_main (libc.so.6)
#11 0x0000560e6003f9da _start (urxvt)
After bisection, it was found the first bad commit is bd4c82c22c36 ("mm,
THP, swap: delay splitting THP after swapped out").
The root cause is as follows:
When the pages are written to swap device during swapping out in
swap_writepage(), zswap (fontswap) is tried to compress the pages to
improve performance. But zswap (frontswap) will treat THP as a normal
page, so only the head page is saved. After swapping in, tail pages
will not be restored to their original contents, causing memory
corruption in the applications.
This is fixed by refusing to save page in the frontswap store functions
if the page is a THP. So that the THP will be swapped out to swap
device.
Another choice is to split THP if frontswap is enabled. But it is found
that the frontswap enabling isn't flexible. For example, if
CONFIG_ZSWAP=y (cannot be module), frontswap will be enabled even if
zswap itself isn't enabled.
Frontswap has multiple backends, to make it easy for one backend to
enable THP support, the THP checking is put in backend frontswap store
functions instead of the general interfaces.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: bd4c82c22c367e068 ("mm, THP, swap: delay splitting THP after swapped out")
Signed-off-by: "Huang, Ying" <[email protected]>
Reported-by: Sergey Senozhatsky <[email protected]>
Tested-by: Sergey Senozhatsky <[email protected]>
Suggested-by: Minchan Kim <[email protected]> [put THP checking in backend]
Cc: Konrad Rzeszutek Wilk <[email protected]>
Cc: Dan Streetman <[email protected]>
Cc: Seth Jennings <[email protected]>
Cc: Tetsuo Handa <[email protected]>
Cc: Shaohua Li <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Johannes Weiner <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: Shakeel Butt <[email protected]>
Cc: Boris Ostrovsky <[email protected]>
Cc: Juergen Gross <[email protected]>
Cc: <[email protected]> [4.14]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
const must be marked __initconst, not __initdata.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Andi Kleen <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
chan->n_subbufs is set by the user and relay_create_buf() does a kmalloc()
of chan->n_subbufs * sizeof(size_t *).
kmalloc_slab() will generate a warning when this fails if
chan->subbufs * sizeof(size_t *) > KMALLOC_MAX_SIZE.
Limit chan->n_subbufs to the maximum allowed kmalloc() size.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: f6302f1bcd75 ("relay: prevent integer overflow in relay_open()")
Signed-off-by: David Rientjes <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Cc: Jens Axboe <[email protected]>
Cc: Dave Jiang <[email protected]>
Cc: Al Viro <[email protected]>
Cc: Dan Carpenter <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
When a thread mlocks an address space backed either by file pages which
are currently not present in memory or swapped out anon pages (not in
swapcache), a new page is allocated and added to the local pagevec
(lru_add_pvec), I/O is triggered and the thread then sleeps on the page.
On I/O completion, the thread can wake on a different CPU, the mlock
syscall will then sets the PageMlocked() bit of the page but will not be
able to put that page in unevictable LRU as the page is on the pagevec
of a different CPU. Even on drain, that page will go to evictable LRU
because the PageMlocked() bit is not checked on pagevec drain.
The page will eventually go to right LRU on reclaim but the LRU stats
will remain skewed for a long time.
This patch puts all the pages, even unevictable, to the pagevecs and on
the drain, the pages will be added on their LRUs correctly by checking
their evictability. This resolves the mlocked pages on pagevec of other
CPUs issue because when those pagevecs will be drained, the mlocked file
pages will go to unevictable LRU. Also this makes the race with munlock
easier to resolve because the pagevec drains happen in LRU lock.
However there is still one place which makes a page evictable and does
PageLRU check on that page without LRU lock and needs special attention.
TestClearPageMlocked() and isolate_lru_page() in clear_page_mlock().
#0: __pagevec_lru_add_fn #1: clear_page_mlock
SetPageLRU() if (!TestClearPageMlocked())
return
smp_mb() // <--required
// inside does PageLRU
if (!PageMlocked()) if (isolate_lru_page())
move to evictable LRU putback_lru_page()
else
move to unevictable LRU
In '#1', TestClearPageMlocked() provides full memory barrier semantics
and thus the PageLRU check (inside isolate_lru_page) can not be
reordered before it.
In '#0', without explicit memory barrier, the PageMlocked() check can be
reordered before SetPageLRU(). If that happens, '#0' can put a page in
unevictable LRU and '#1' might have just cleared the Mlocked bit of that
page but fails to isolate as PageLRU fails as '#0' still hasn't set
PageLRU bit of that page. That page will be stranded on the unevictable
LRU.
There is one (good) side effect though. Without this patch, the pages
allocated for System V shared memory segment are added to evictable LRUs
even after shmctl(SHM_LOCK) on that segment. This patch will correctly
put such pages to unevictable LRU.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Shakeel Butt <[email protected]>
Acked-by: Vlastimil Babka <[email protected]>
Cc: Jérôme Glisse <[email protected]>
Cc: Huang Ying <[email protected]>
Cc: Tim Chen <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Greg Thelen <[email protected]>
Cc: Johannes Weiner <[email protected]>
Cc: Balbir Singh <[email protected]>
Cc: Minchan Kim <[email protected]>
Cc: Shaohua Li <[email protected]>
Cc: Jan Kara <[email protected]>
Cc: Nicholas Piggin <[email protected]>
Cc: Dan Williams <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: Hugh Dickins <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
After commit a983b5ebee57 ("mm: memcontrol: fix excessive complexity in
memory.stat reporting"), we observed slowly upward creeping NR_WRITEBACK
counts over the course of several days, both the per-memcg stats as well
as the system counter in e.g. /proc/meminfo.
The conversion from full per-cpu stat counts to per-cpu cached atomic
stat counts introduced an irq-unsafe RMW operation into the updates.
Most stat updates come from process context, but one notable exception
is the NR_WRITEBACK counter. While writebacks are issued from process
context, they are retired from (soft)irq context.
When writeback completions interrupt the RMW counter updates of new
writebacks being issued, the decs from the completions are lost.
Since the global updates are routed through the joint lruvec API, both
the memcg counters as well as the system counters are affected.
This patch makes the joint stat and event API irq safe.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: a983b5ebee57 ("mm: memcontrol: fix excessive complexity in memory.stat reporting")
Signed-off-by: Johannes Weiner <[email protected]>
Debugged-by: Tejun Heo <[email protected]>
Reviewed-by: Rik van Riel <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Cc: Vladimir Davydov <[email protected]>
Cc: Michal Hocko <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Build testing with LTO found a couple of files that get compiled
differently depending on whether asm/byteorder.h gets included early
enough or not. In particular, include/asm-generic/qrwlock_types.h is
affected by this, but there are probably others as well.
The symptom is a series of LTO link time warnings, including these:
net/netlabel/netlabel_unlabeled.h:223: error: type of 'netlbl_unlhsh_add' does not match original declaration [-Werror=lto-type-mismatch]
int netlbl_unlhsh_add(struct net *net,
net/netlabel/netlabel_unlabeled.c:377: note: 'netlbl_unlhsh_add' was previously declared here
include/net/ipv6.h:360: error: type of 'ipv6_renew_options_kern' does not match original declaration [-Werror=lto-type-mismatch]
ipv6_renew_options_kern(struct sock *sk,
net/ipv6/exthdrs.c:1162: note: 'ipv6_renew_options_kern' was previously declared here
net/core/dev.c:761: note: 'dev_get_by_name_rcu' was previously declared here
struct net_device *dev_get_by_name_rcu(struct net *net, const char *name)
net/core/dev.c:761: note: code may be misoptimized unless -fno-strict-aliasing is used
drivers/gpu/drm/i915/i915_drv.h:3377: error: type of 'i915_gem_object_set_to_wc_domain' does not match original declaration [-Werror=lto-type-mismatch]
i915_gem_object_set_to_wc_domain(struct drm_i915_gem_object *obj, bool write);
drivers/gpu/drm/i915/i915_gem.c:3639: note: 'i915_gem_object_set_to_wc_domain' was previously declared here
include/linux/debugfs.h:92:9: error: type of 'debugfs_attr_read' does not match original declaration [-Werror=lto-type-mismatch]
ssize_t debugfs_attr_read(struct file *file, char __user *buf,
fs/debugfs/file.c:318: note: 'debugfs_attr_read' was previously declared here
include/linux/rwlock_api_smp.h:30: error: type of '_raw_read_unlock' does not match original declaration [-Werror=lto-type-mismatch]
void __lockfunc _raw_read_unlock(rwlock_t *lock) __releases(lock);
kernel/locking/spinlock.c:246:26: note: '_raw_read_unlock' was previously declared here
include/linux/fs.h:3308:5: error: type of 'simple_attr_open' does not match original declaration [-Werror=lto-type-mismatch]
int simple_attr_open(struct inode *inode, struct file *file,
fs/libfs.c:795: note: 'simple_attr_open' was previously declared here
All of the above are caused by include/asm-generic/qrwlock_types.h
failing to include asm/byteorder.h after commit e0d02285f16e
("locking/qrwlock: Use 'struct qrwlock' instead of 'struct __qrwlock'")
in linux-4.15.
Similar bugs may or may not exist in older kernels as well, but there is
no easy way to test those with link-time optimizations, and kernels
before 4.14 are harder to fix because they don't have Babu's patch
series
We had similar issues with CONFIG_ symbols in the past and ended up
always including the configuration headers though linux/kconfig.h. This
works around the issue through that same file, defining either
__BIG_ENDIAN or __LITTLE_ENDIAN depending on CONFIG_CPU_BIG_ENDIAN,
which is now always set on all architectures since commit 4c97a0c8fee3
("arch: define CPU_BIG_ENDIAN for all fixed big endian archs").
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
Cc: Babu Moger <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Masahiro Yamada <[email protected]>
Cc: Nicolas Pitre <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Will Deacon <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
As Peter points out, Doing a CALL+RET for just the decrement is a bit silly.
Fixes: d70f2a14b72a4bc ("include/linux/sched/mm.h: uninline mmdrop_async(), etc")
Acked-by: Peter Zijlstra (Intel) <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Oleg Nesterov <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Currently a number of Makefiles break when used with toolchains that
pass extra flags in CC and other cross-compile related variables (such
as --sysroot).
Thus we get this error when we use a toolchain that puts --sysroot in
the CC var:
~/src/linux/tools$ make iio
[snip]
iio_event_monitor.c:18:10: fatal error: unistd.h: No such file or directory
#include <unistd.h>
^~~~~~~~~~
This occurs because we clobber several env vars related to
cross-compiling with lines like this:
CC = $(CROSS_COMPILE)gcc
Although this will point to a valid cross-compiler, we lose any extra
flags that might exist in the CC variable, which can break toolchains
that rely on them (for example, those that use --sysroot).
This easily shows up using a Yocto SDK:
$ . [snip]/sdk/environment-setup-cortexa8hf-neon-poky-linux-gnueabi
$ echo $CC
arm-poky-linux-gnueabi-gcc -march=armv7-a -mfpu=neon -mfloat-abi=hard
-mcpu=cortex-a8
--sysroot=[snip]/sdk/sysroots/cortexa8hf-neon-poky-linux-gnueabi
$ echo $CROSS_COMPILE
arm-poky-linux-gnueabi-
$ echo ${CROSS_COMPILE}gcc
krm-poky-linux-gnueabi-gcc
Although arm-poky-linux-gnueabi-gcc is a cross-compiler, we've lost the
--sysroot and other flags that enable us to find the right libraries to
link against, so we can't find unistd.h and other libraries and headers.
Normally with the --sysroot flag we would find unistd.h in the sdk
directory in the sysroot:
$ find [snip]/sdk/sysroots -path '*/usr/include/unistd.h'
[snip]/sdk/sysroots/cortexa8hf-neon-poky-linux-gnueabi/usr/include/unistd.h
The perf Makefile adds CC = $(CROSS_COMPILE)gcc if and only if CC is not
already set, and it compiles correctly with the above toolchain.
So, generalize the logic that perf uses in the common Makefile and
remove the manual CC = $(CROSS_COMPILE)gcc lines from each Makefile.
Note that this patch does not fix cross-compile for all the tools (some
have other bugs), but it does fix it for all except usb and acpi, which
still have other unrelated issues.
I tested both with and without the patch on native and cross-build and
there appear to be no regressions.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Martin Kelly <[email protected]>
Acked-by: Mark Brown <[email protected]>
Cc: Tejun Heo <[email protected]>
Cc: Li Zefan <[email protected]>
Cc: Johannes Weiner <[email protected]>
Cc: Linus Walleij <[email protected]>
Cc: "K. Y. Srinivasan" <[email protected]>
Cc: Haiyang Zhang <[email protected]>
Cc: Stephen Hemminger <[email protected]>
Cc: Jonathan Cameron <[email protected]>
Cc: Pali Rohar <[email protected]>
Cc: Richard Purdie <[email protected]>
Cc: Jacek Anaszewski <[email protected]>
Cc: Pavel Machek <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Arnaldo Carvalho de Melo <[email protected]>
Cc: Robert Moore <[email protected]>
Cc: Lv Zheng <[email protected]>
Cc: "Rafael J. Wysocki" <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Valentina Manea <[email protected]>
Cc: Shuah Khan <[email protected]>
Cc: Mario Limonciello <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for 4.16. I contains fixes for deadlock on runtime suspend on few
drivers, a memory leak on non-blocking commits, a crash on color-eviction.
The is also meson and edid fixes, plus a fix for a doc warning.
* tag 'drm-misc-fixes-2018-02-21' of git://anongit.freedesktop.org/drm/drm-misc:
drm/tve200: fix kernel-doc documentation comment include
drm/meson: fix vsync buffer update
drm: Handle unexpected holes in color-eviction
drm/edid: Add 6 bpc quirk for CPT panel in Asus UX303LA
drm/amdgpu: Fix deadlock on runtime suspend
drm/radeon: Fix deadlock on runtime suspend
drm/nouveau: Fix deadlock on runtime suspend
drm: Allow determining if current task is output poll worker
workqueue: Allow retrieval of current task's work struct
drm/atomic: Fix memleak on ERESTARTSYS during non-blocking commits
|
|
Passing a pointer to a unsigned integer to test_bit() is broken.
Signed-off-by: Trond Myklebust <[email protected]>
|
|
After resuming from suspend, the PCI device support must re-enable the
interrupt setting so that interrupts are actually delivered.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2018-02-20
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a memory leak in LPM trie's map_free() callback function, where
the trie structure itself was not freed since initial implementation.
Also a synchronize_rcu() was needed in order to wait for outstanding
programs accessing the trie to complete, from Yonghong.
2) Fix sock_map_alloc()'s error path in order to correctly propagate
the -EINVAL error in case of too large allocation requests. This
was just recently introduced when fixing close hooks via ULP layer,
fix from Eric.
3) Do not use GFP_ATOMIC in __cpu_map_entry_alloc(). Reason is that this
will not work with the recent __ptr_ring_init_queue_alloc() conversion
to kvmalloc_array(), where in case of fallback to vmalloc() that GFP
flag is invalid, from Jason.
4) Fix two recent syzkaller warnings: i) fix bpf_prog_array_copy_to_user()
when a prog query with a big number of ids was performed where we'd
otherwise trigger a warning from allocator side, ii) fix a missing
mlock precharge on arraymaps, from Daniel.
5) Two fixes for bpftool in order to avoid breaking JSON output when used
in batch mode, from Quentin.
6) Move a pr_debug() in libbpf in order to avoid having an otherwise
uninitialized variable in bpf_program__reloc_text(), from Jeremy.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Jesper Dangaard Brouer says:
====================
virtio_net: several bugs in XDP code for driver virtio_net
The virtio_net driver actually violates the original memory model of
XDP causing hard to debug crashes. Per request of John Fastabend,
instead of removing the XDP feature I'm fixing as much as possible.
While testing virtio_net with XDP_REDIRECT I found 4 different bugs.
Patch-1: not enough tail-room for build_skb in receive_mergeable()
only option is to disable XDP_REDIRECT in receive_mergeable()
Patch-2: XDP in receive_small() basically never worked (check wrong flag)
Patch-3: fix memory leak for XDP_REDIRECT in error cases
Patch-4: avoid crash when ndo_xdp_xmit is called on dev not ready for XDP
In the longer run, we should consider introducing a separate receive
function when attaching an XDP program, and also change the memory
model to be compatible with XDP when attaching an XDP prog.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
When a driver implements the ndo_xdp_xmit() function, there is
(currently) no generic way to determine whether it is safe to call.
It is e.g. unsafe to call the drivers ndo_xdp_xmit, if it have not
allocated the needed XDP TX queues yet. This is the case for
virtio_net, which first allocates the XDP TX queues once an XDP/bpf
prog is attached (in virtnet_xdp_set()).
Thus, a crash will occur for virtio_net when redirecting to another
virtio_net device's ndo_xdp_xmit, which have not attached a XDP prog.
The sample xdp_redirect_map tries to attach a dummy XDP prog to take
this into account, but it can also easily fail if the virtio_net (or
actually underlying vhost driver) have not allocated enough extra
queues for the device.
Allocating more queue this is currently a manual config.
Hint for libvirt XML add:
<driver name='vhost' queues='16'>
<host mrg_rxbuf='off'/>
<guest tso4='off' tso6='off' ecn='off' ufo='off'/>
</driver>
The solution in this patch is to check that the device have loaded an
XDP/bpf prog before proceeding. This is similar to the check
performed in driver ixgbe.
Signed-off-by: Jesper Dangaard Brouer <[email protected]>
Acked-by: John Fastabend <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
XDP_REDIRECT calling xdp_do_redirect() can fail for multiple reasons
(which can be inspected by tracepoints). The current semantics is that
on failure the driver calling xdp_do_redirect() must handle freeing or
recycling the page associated with this frame. This can be seen as an
optimization, as drivers usually have an optimized XDP_DROP code path
for frame recycling in place already.
The virtio_net driver didn't handle when xdp_do_redirect() failed.
This caused a memory leak as the page refcnt wasn't decremented on
failures.
The function __virtnet_xdp_xmit() did handle one type of failure,
when the xmit queue virtqueue_add_outbuf() is full, which "hides"
releasing a refcnt on the page. Instead the function __virtnet_xdp_xmit()
must follow API of xdp_do_redirect(), which on errors leave it up to
the caller to free the page, of the failed send operation.
Fixes: 186b3c998c50 ("virtio-net: support XDP_REDIRECT")
Signed-off-by: Jesper Dangaard Brouer <[email protected]>
Acked-by: John Fastabend <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When configuring virtio_net to use the code path 'receive_small()',
in-order to get correct XDP_REDIRECT support, I discovered TCP packets
would get silently dropped when loading an XDP program action XDP_PASS.
The bug seems to be that receive_small() when XDP is loaded check that
hdr->hdr.flags is zero, which seems wrong as hdr.flags contains the
flags VIRTIO_NET_HDR_F_* :
#define VIRTIO_NET_HDR_F_NEEDS_CSUM 1 /* Use csum_start, csum_offset */
#define VIRTIO_NET_HDR_F_DATA_VALID 2 /* Csum is valid */
TCP got dropped as it had the VIRTIO_NET_HDR_F_DATA_VALID flag set.
The flags that are relevant here are the VIRTIO_NET_HDR_GSO_* flags
stored in hdr->hdr.gso_type. Thus, the fix is just check that none of
the gso_type flags have been set.
Fixes: bb91accf2733 ("virtio-net: XDP support for small buffers")
Signed-off-by: Jesper Dangaard Brouer <[email protected]>
Acked-by: John Fastabend <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The virtio_net code have three different RX code-paths in receive_buf().
Two of these code paths can handle XDP, but one of them is broken for
at least XDP_REDIRECT.
Function(1): receive_big() does not support XDP.
Function(2): receive_small() support XDP fully and uses build_skb().
Function(3): receive_mergeable() broken XDP_REDIRECT uses napi_alloc_skb().
The simple explanation is that receive_mergeable() is broken because
it uses napi_alloc_skb(), which violates XDP given XDP assumes packet
header+data in single page and enough tail room for skb_shared_info.
The longer explaination is that receive_mergeable() tries to
work-around and satisfy these XDP requiresments e.g. by having a
function xdp_linearize_page() that allocates and memcpy RX buffers
around (in case packet is scattered across multiple rx buffers). This
does currently satisfy XDP_PASS, XDP_DROP and XDP_TX (but only because
we have not implemented bpf_xdp_adjust_tail yet).
The XDP_REDIRECT action combined with cpumap is broken, and cause hard
to debug crashes. The main issue is that the RX packet does not have
the needed tail-room (SKB_DATA_ALIGN(skb_shared_info)), causing
skb_shared_info to overlap the next packets head-room (in which cpumap
stores info).
Reproducing depend on the packet payload length and if RX-buffer size
happened to have tail-room for skb_shared_info or not. But to make
this even harder to troubleshoot, the RX-buffer size is runtime
dynamically change based on an Exponentially Weighted Moving Average
(EWMA) over the packet length, when refilling RX rings.
This patch only disable XDP_REDIRECT support in receive_mergeable()
case, because it can cause a real crash.
IMHO we should consider NOT supporting XDP in receive_mergeable() at
all, because the principles behind XDP are to gain speed by (1) code
simplicity, (2) sacrificing memory and (3) where possible moving
runtime checks to setup time. These principles are clearly being
violated in receive_mergeable(), that e.g. runtime track average
buffer size to save memory consumption.
In the longer run, we should consider introducing a separate receive
function when attaching an XDP program, and also change the memory
model to be compatible with XDP when attaching an XDP prog.
Fixes: 186b3c998c50 ("virtio-net: support XDP_REDIRECT")
Signed-off-by: Jesper Dangaard Brouer <[email protected]>
Acked-by: John Fastabend <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-02-20
The following pull request includes some fixes for the mlx5 core and
netdevice driver.
Please pull and let me know if there's any issue.
-stable 4.10.y:
('net/mlx5e: Fix loopback self test when GRO is off')
-stable 4.12.y:
('net/mlx5e: Specify numa node when allocating drop rq')
-stable 4.13.y:
('net/mlx5e: Verify inline header size do not exceed SKB linear size')
-stable 4.15.y:
('net/mlx5e: Fix TCP checksum in LRO buffers')
('net/mlx5: Fix error handling when adding flow rules')
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains large batch with Netfilter fixes for
your net tree, mostly due to syzbot report fixups and pr_err()
ratelimiting, more specifically, they are:
1) Get rid of superfluous unnecessary check in x_tables before vmalloc(),
we don't hit BUG there anymore, patch from Michal Hock, suggested by
Andrew Morton.
2) Race condition in proc file creation in ipt_CLUSTERIP, from Cong Wang.
3) Drop socket lock that results in circular locking dependency, patch
from Paolo Abeni.
4) Drop packet if case of malformed blob that makes backpointer jump
in x_tables, from Florian Westphal.
5) Fix refcount leak due to race in ipt_CLUSTERIP in
clusterip_config_find_get(), from Cong Wang.
6) Several patches to ratelimit pr_err() for x_tables since this can be
a problem where CAP_NET_ADMIN semantics can protect us in untrusted
namespace, from Florian Westphal.
7) Missing .gitignore update for new autogenerated asn1 state machine
for the SNMP NAT helper, from Zhu Lingshan.
8) Missing timer initialization in xt_LED, from Paolo Abeni.
9) Do not allow negative port range in NAT, also from Paolo.
10) Lock imbalance in the xt_hashlimit rate match mode, patch from
Eric Dumazet.
11) Initialize workqueue before timer in the idletimer match,
from Eric Dumazet.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Attempt to modify XRC_TGT QP type from the user space (ibv_xsrq_pingpong
invocation) will trigger the following kernel panic. It is caused by the
fact that such QPs missed uobject initialization.
[ 17.408845] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[ 17.412645] IP: rdma_lookup_put_uobject+0x9/0x50
[ 17.416567] PGD 0 P4D 0
[ 17.419262] Oops: 0000 [#1] SMP PTI
[ 17.422915] CPU: 0 PID: 455 Comm: ibv_xsrq_pingpo Not tainted 4.16.0-rc1+ #86
[ 17.424765] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
[ 17.427399] RIP: 0010:rdma_lookup_put_uobject+0x9/0x50
[ 17.428445] RSP: 0018:ffffb8c7401e7c90 EFLAGS: 00010246
[ 17.429543] RAX: 0000000000000000 RBX: ffffb8c7401e7cf8 RCX: 0000000000000000
[ 17.432426] RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000000000000000
[ 17.437448] RBP: 0000000000000000 R08: 00000000000218f0 R09: ffffffff8ebc4cac
[ 17.440223] R10: fffff6038052cd80 R11: ffff967694b36400 R12: ffff96769391f800
[ 17.442184] R13: ffffb8c7401e7cd8 R14: 0000000000000000 R15: ffff967699f60000
[ 17.443971] FS: 00007fc29207d700(0000) GS:ffff96769fc00000(0000) knlGS:0000000000000000
[ 17.446623] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 17.448059] CR2: 0000000000000048 CR3: 000000001397a000 CR4: 00000000000006b0
[ 17.449677] Call Trace:
[ 17.450247] modify_qp.isra.20+0x219/0x2f0
[ 17.451151] ib_uverbs_modify_qp+0x90/0xe0
[ 17.452126] ib_uverbs_write+0x1d2/0x3c0
[ 17.453897] ? __handle_mm_fault+0x93c/0xe40
[ 17.454938] __vfs_write+0x36/0x180
[ 17.455875] vfs_write+0xad/0x1e0
[ 17.456766] SyS_write+0x52/0xc0
[ 17.457632] do_syscall_64+0x75/0x180
[ 17.458631] entry_SYSCALL_64_after_hwframe+0x21/0x86
[ 17.460004] RIP: 0033:0x7fc29198f5a0
[ 17.460982] RSP: 002b:00007ffccc71f018 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 17.463043] RAX: ffffffffffffffda RBX: 0000000000000078 RCX: 00007fc29198f5a0
[ 17.464581] RDX: 0000000000000078 RSI: 00007ffccc71f050 RDI: 0000000000000003
[ 17.466148] RBP: 0000000000000000 R08: 0000000000000078 R09: 00007ffccc71f050
[ 17.467750] R10: 000055b6cf87c248 R11: 0000000000000246 R12: 00007ffccc71f300
[ 17.469541] R13: 000055b6cf8733a0 R14: 0000000000000000 R15: 0000000000000000
[ 17.471151] Code: 00 00 0f 1f 44 00 00 48 8b 47 48 48 8b 00 48 8b 40 10 e9 0b 8b 68 00 90 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 53 89 f5 <48> 8b 47 48 48 89 fb 40 0f b6 f6 48 8b 00 48 8b 40 20 e8 e0 8a
[ 17.475185] RIP: rdma_lookup_put_uobject+0x9/0x50 RSP: ffffb8c7401e7c90
[ 17.476841] CR2: 0000000000000048
[ 17.477764] ---[ end trace 1dbcc5354071a712 ]---
[ 17.478880] Kernel panic - not syncing: Fatal exception
[ 17.480277] Kernel Offset: 0xd000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
Fixes: 2f08ee363fe0 ("RDMA/restrack: don't use uaccess_kernel()")
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
Continuing along with the fight against smp_read_barrier_depends() [1]
(or rather, against its improper use), add an unconditional barrier to
cmpxchg. This guarantees that dependency ordering is preserved when a
dependency is headed by an unsuccessful cmpxchg. As it turns out, the
change could enable further simplification of LKMM as proposed in [2].
[1] https://marc.info/?l=linux-kernel&m=150884953419377&w=2
https://marc.info/?l=linux-kernel&m=150884946319353&w=2
https://marc.info/?l=linux-kernel&m=151215810824468&w=2
https://marc.info/?l=linux-kernel&m=151215816324484&w=2
[2] https://marc.info/?l=linux-kernel&m=151881978314872&w=2
Signed-off-by: Andrea Parri <[email protected]>
Acked-by: Peter Zijlstra <[email protected]>
Acked-by: Paul E. McKenney <[email protected]>
Cc: Alan Stern <[email protected]>
Cc: Ivan Kokshaysky <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Matt Turner <[email protected]>
Cc: Richard Henderson <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Will Deacon <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
GCC-8 shows a warning for the x86 oprofile code that copies per-CPU
data from CPU 0 to all other CPUs, which when building a non-SMP
kernel turns into a memcpy() with identical source and destination
pointers:
arch/x86/oprofile/nmi_int.c: In function 'mux_clone':
arch/x86/oprofile/nmi_int.c:285:2: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
memcpy(per_cpu(cpu_msrs, cpu).multiplex,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
per_cpu(cpu_msrs, 0).multiplex,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(struct op_msr) * model->num_virt_counters);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/x86/oprofile/nmi_int.c: In function 'nmi_setup':
arch/x86/oprofile/nmi_int.c:466:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
arch/x86/oprofile/nmi_int.c:470:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
I have analyzed a number of such warnings now: some are valid and the
GCC warning is welcome. Others turned out to be false-positives, and
GCC was changed to not warn about those any more. This is a corner case
that is a false-positive but the GCC developers feel it's better to keep
warning about it.
In this case, it seems best to work around it by telling GCC
a little more clearly that this code path is never hit with
an IS_ENABLED() configuration check.
Cc:stable as we also want old kernels to build cleanly with GCC-8.
Signed-off-by: Arnd Bergmann <[email protected]>
Cc: Jessica Yu <[email protected]>
Cc: Kees Cook <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Martin Sebor <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Robert Richter <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=84095
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Commits adding PCI IDs for Intel Braswell and Kaby Lake PCH-H lacked the
respective Kconfig and Documentation/i2c/busses/i2c-i801 change. Add
them now.
Signed-off-by: Jarkko Nikula <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
|
|
One I2C bus on my Atom E3845 board has been broken since 4.9.
It has two devices, both declared by ACPI and with built-in drivers.
There are two back-to-back transactions originating from the kernel, one
targeting each device. The first transaction works, the second one locks
up the I2C controller. The controller never recovers.
These kernel logs show up whenever an I2C transaction is attempted after
this failure.
i2c-designware-pci 0000:00:18.3: timeout in disabling adapter
i2c-designware-pci 0000:00:18.3: timeout waiting for bus ready
Waiting for the I2C controller status to indicate that it is enabled
before programming it fixes the issue.
I have tested this patch on 4.14 and 4.15.
Fixes: commit 2702ea7dbec5 ("i2c: designware: wait for disable/enable only if necessary")
Cc: linux-stable <[email protected]> #4.13+
Signed-off-by: Ben Gardner <[email protected]>
Acked-by: Jarkko Nikula <[email protected]>
Reviewed-by: José Roberto de Souza <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
|
|
Attempt to deter usage, this is not a public interface. It is entirely
possible to implement a conformant mutex without having this owner
field (in fact, we used to have that).
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Paul E. McKenney <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
The DOC: line acts as an identifier for the :doc: include. Fixes:
./drivers/gpu/drm/tve200/tve200_drv.c:1: warning: no structured comments found
Cc: Linus Walleij <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
So far, if the filter was too large to fit in the allocated skb, the
kernel did not return any error and stopped dumping. Modify the dumper
so that it returns -EMSGSIZE when a filter fails to dump and it is the
first filter in the skb. If we are not first, we will get a next chance
with more room.
I understand this is pretty near to being an API change, but the
original design (silent truncation) can be considered a bug.
Note: The error case can happen pretty easily if you create a filter
with 32 actions and have 4kb pages. Also recent versions of iproute try
to be clever with their buffer allocation size, which in turn leads to
Signed-off-by: Roman Kapl <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Acked-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This uses the EDID info from the Sony PlayStation VR headset,
when connected directly, to mark it as non-desktop.
Since the connection box (product id b403) defaults to HDMI
pass-through to the TV, it is not marked as non-desktop.
Signed-off-by: Philipp Zabel <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
This uses the EDID info from Lenovo Explorer (LEN-b800), Acer AH100
(ACR-7fce), and Samsung Odyssey (SEC-144a) to mark them as non-desktop.
The other entries are for the HP Windows Mixed Reality Headset (HPN-3515),
the Fujitsu Windows Mixed Reality headset (FUJ-1970), the Dell Visor
(DEL-7fce), and the ASUS HC102 (AUS-c102). They are not tested with real
hardware, but listed as HMD monitors alongside the tested headsets in the
Microsoft HololensSensors driver package.
Signed-off-by: Philipp Zabel <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
This uses the EDID info from Oculus Rift DK1 (OVR-0001), DK2 (OVR-0003),
and CV1 (OVR-0004) to mark them as non-desktop.
Signed-off-by: Philipp Zabel <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
Fix some issues found by a static checker:
When allocating an AFU interrupt, if the driver cannot copy the output
parameters to userland, the errno value was not set to EFAULT
Remove a (now) useless cast.
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Frederic Barrat <[email protected]>
Acked-by: Andrew Donnellan <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
The notify_resume() callback in eeh_ops is NULL on powernv, leading to
crashes:
NIP (null)
LR eeh_report_resume+0x218/0x220
Call Trace:
eeh_report_resume+0x1f0/0x220 (unreliable)
eeh_pe_dev_traverse+0x98/0x170
eeh_handle_normal_event+0x3f4/0x650
eeh_handle_event+0x54/0x380
eeh_event_handler+0x14c/0x210
kthread+0x168/0x1b0
ret_from_kernel_thread+0x5c/0xb4
Fix it by adding a check before calling it.
Fixes: 856e1eb9bdd4 ("PCI/AER: Add uevents in AER and EEH error/resume")
Signed-off-by: Juan J. Alvarez <[email protected]>
Reviewed-by: Bryant G. Ly <[email protected]>
Tested-by: Carol L. Soto <[email protected]>
Reviewed-by: Andrew Donnellan <[email protected]>
Tested-by: Mauro S. M. Rodrigues <[email protected]>
Acked-by: Michael Neuling <[email protected]>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- fix lut loading for cirrus
* tag 'drm-misc-fixes-2018-01-31' of git://anongit.freedesktop.org/drm/drm-misc:
drm/cirrus: Load lut in crtc_commit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
- three fixeups
. it fixes potential issues[1] by using monotonic timestamp
instead of 'struct timeval'
. correct HDMI_I2S_PIN_SEL_1 definition and setting value.
. fix bit shift typo of FIMC register definition
- two cleanups
. remove unnecessary error messages
. remove exynos_drm_rotator.h file
[1] https://patchwork.kernel.org/patch/10170205/
* tag 'exynos-drm-fixes-for-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm: exynos: Use proper macro definition for HDMI_I2S_PIN_SEL_1
drm/exynos: remove exynos_drm_rotator.h
drm/exynos: g2d: Delete an error message for a failed memory allocation in two functions
drm/exynos: fix comparison to bitshift when dealing with a mask
drm/exynos: g2d: use monotonic timestamps
|
|
If building match list or adding existing fg fails when
node is locked, function returned without unlocking it.
This happened if node version changed or adding existing fg
returned with EAGAIN after jumping to search_again_locked label.
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Vlad Buslov <[email protected]>
Reviewed-by: Maor Gottlieb <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
First use of drop counters happens in esw_apply_vport_conf function,
while they are allocated later in the flow. Fix that by moving
esw_vport_create_drop_counters function to be called before the first use.
Fixes: b8a0dbe3a90b ("net/mlx5e: E-switch, Add steering drop counters")
Signed-off-by: Eugenia Emantayev <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
We can't allow only some of the rules sharing an FTE to ask for
header re-write, add it to the conflicting action checks.
Fixes: 0d235c3fabb7 ('net/mlx5: Add hash table to search FTEs in a flow-group')
Signed-off-by: Or Gerlitz <[email protected]>
Reviewed-by: Matan Barak <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
The adapter uses the cache_line_128byte setting to set the bounds for
end padding. On systems where the cacheline size is greater than 128B
use 128B instead of the default of 64B. This results in fewer partial
cacheline writes. There's a 50% chance it will pad to the end of a 256B
cache line vs only 25% when using 64B.
Fixes: f32f5bd2eb7e ("net/mlx5: Configure cache line size for start and end padding")
Signed-off-by: Daniel Jurgens <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
When allocating a drop rq, no numa node is explicitly set which means
allocations are done on node zero. This is not necessarily the nearest
numa node to the HCA, and even worse, might even be a memoryless numa
node.
Choose the numa_node given to us by the pci device in order to properly
allocate the coherent dma memory instead of assuming zero is valid.
Fixes: 556dd1b9c313 ("net/mlx5e: Set drop RQ's necessary parameters only")
Signed-off-by: Gal Pressman <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
This isn't supported when we emulate eswitch vlan push action which
is the current state of things.
Fixes: 8b32580df1cb ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <[email protected]>
Reviewed-by: Mark Bloch <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Address these sparse warnings on drivers/net/ethernet/mellanox/mlx5
[..]/core/diag/fs_tracepoint.c:99:53: warning: non-constant initializer for static object
[..]/core/diag/fs_tracepoint.c:102:53: warning: non-constant initializer for static object
etc
Signed-off-by: Or Gerlitz <[email protected]>
Reviewed-by: Matan Barak <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Fix these gcc warnings on drivers/net/ethernet/mellanox/mlx5:
[..]/core/lib/clock.c:454:6: warning: no previous prototype for 'mlx5_init_clock' [-Wmissing-prototypes]
[..]/core/lib/clock.c:510:6: warning: no previous prototype for 'mlx5_cleanup_clock' [-Wmissing-prototypes]
[..]/core/en_main.c:3141:5: warning: no previous prototype for 'mlx5e_setup_tc' [-Wmissing-prototypes]
Signed-off-by: Or Gerlitz <[email protected]>
Reviewed-by: Matan Barak <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Driver tries to copy at least MLX5E_MIN_INLINE bytes into the control
segment of the WQE. It assumes that the linear part contains at least
MLX5E_MIN_INLINE bytes, which can be wrong.
Cited commit verified that driver will not copy more bytes into the
inline header part that the actual size of the packet. Re-factor this
check to make sure we do not exceed the linear part as well.
This fix is aligned with the current driver's assumption that the entire
L2 will be present in the linear part of the SKB.
Fixes: 6aace17e64f4 ("net/mlx5e: Fix inline header size for small packets")
Signed-off-by: Eran Ben Elisha <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
When GRO is off, the transport header pointer in sk_buff is
initialized to network's header.
To find the udp header, instead of using udp_hdr() which assumes
skb_network_header was set, manually calculate the udp header offset.
Fixes: 0952da791c97 ("net/mlx5e: Add support for loopback selftest")
Signed-off-by: Inbar Karmy <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
When receiving an LRO packet, the checksum field is set by the hardware
to the checksum of the first coalesced packet. Obviously, this checksum
is not valid for the merged LRO packet and should be fixed. We can use
the CQE checksum which covers the checksum of the entire merged packet
TCP payload to help us calculate the checksum incrementally.
Tested by sending IPv4/6 traffic with LRO enabled, RX checksum disabled
and watching nstat checksum error counters (in addition to the obvious
bandwidth drop caused by checksum errors).
This bug is usually "hidden" since LRO packets would go through the
CHECKSUM_UNNECESSARY flow which does not validate the packet checksum.
It's important to note that previous to this patch, LRO packets provided
with CHECKSUM_UNNECESSARY are indeed packets with a correct validated
checksum (even though the checksum inside the TCP header is incorrect),
since the hardware LRO aggregation is terminated upon receiving a packet
with bad checksum.
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Fixes a GCC maybe-uninitialized warning introduced by 48cca7e44f9f.
"text" is only initialized inside the if statement so only print debug
info there.
Fixes: 48cca7e44f9f ("libbpf: add support for bpf_call")
Signed-off-by: Jeremy Cline <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
After introduction of commit d0869c0071e4, there were some instances of
RX queue entries from a previous session (before the device was closed
and reopened) returned to the NAPI polling routine. Since the corresponding
socket buffers were freed, this resulted in a panic on reopen. Include
a check for a NULL skb here to avoid this.
Fixes: d0869c0071e4 ("ibmvnic: Clean RX pool buffers during device close")
Signed-off-by: Thomas Falcon <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The sbi_ prefix would seem to indicate an SBI interface, and save is not
very specific. After applying this patch, reading head.S makes more sense.
Signed-off-by: Michael Clark <[email protected]>
Signed-off-by: Palmer Dabbelt <[email protected]>
|
|
Interrupt is allowed during exception handling.
There are warning messages if the kernel enables the configuration
'CONFIG_DEBUG_ATOMIC_SLEEP=y'.
BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:23
in_atomic(): 0, irqs_disabled(): 1, pid: 43, name: ash
CPU: 0 PID: 43 Comm: ash Tainted: G W 4.15.0-rc8-00089-g89ffdae-dirty #17
Call Trace:
[<000000009abb1587>] walk_stackframe+0x0/0x7a
[<00000000d4f3d088>] ___might_sleep+0x102/0x11a
[<00000000b1fd792a>] down_read+0x18/0x28
[<000000000289ec01>] do_page_fault+0x86/0x2f6
[<00000000012441f6>] _do_fork+0x1b4/0x1e0
[<00000000f46c3e3b>] ret_from_syscall+0xa/0xe
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Zong Li <[email protected]>
Signed-off-by: Palmer Dabbelt <[email protected]>
Signed-off-by: Palmer Dabbelt <[email protected]>
|