aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2014-11-03uas: Add NO_ATA_1X for VIA VL711 devicesHans de Goede1-0/+7
Just like some Seagate enclosures, these devices do not seem to grok ata pass through commands. Cc: [email protected] # 3.16 Signed-off-by: Hans de Goede <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2014-11-03xhci: Disable streams on Asmedia 1042 xhci controllersHans de Goede1-0/+4
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk which is known to work fine with other controllers causes the system to freeze when connected over usb-3 with this controller, where as it works fine with uas in usb-2 ports, indicating a problem with streams. This is a bit bigger hammer then I would like to use for this, but for now it will have to make do. I've ordered a pci-e usb controller card with an Asmedia 1042, once that arrives I'll try to get streams to work (with a quirk flag if necessary) and then we can re-enable them. For now this at least makes uas capable disk enclosures work again by forcing fallback to the usb-storage driver. Reported-by: Bogdan Mihalcea <[email protected]> Cc: Bogdan Mihalcea <[email protected]> Cc: [email protected] # 3.16 Signed-off-by: Hans de Goede <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2014-11-03USB: HWA: fix a warning messageDan Carpenter1-1/+1
We wanted to print the version as (major).(minor) but because the shift operation is higher precedence than the mask then we print (minor).(minor). Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2014-11-03uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate modelHans de Goede1-0/+7
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X quirk to filter these out. Cc: [email protected] # 3.16 Signed-off-by: Hans de Goede <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2014-11-03usb-storage: handle a skipped data phaseAlan Stern1-0/+26
Sometimes mass-storage devices using the Bulk-only transport will mistakenly skip the data phase of a command. Rather than sending the data expected by the host or sending a zero-length packet, they go directly to the status phase and send the CSW. This causes problems for usb-storage, for obvious reasons. The driver will interpret the CSW as a short data transfer and will wait to receive a CSW. The device won't have anything left to send, so the command eventually times out. The SCSI layer doesn't retry commands after they time out (this is a relatively recent change). Therefore we should do our best to detect a skipped data phase and handle it promptly. This patch adds code to do that. If usb-storage receives a short 13-byte data transfer from the device, and if the first four bytes of the data match the CSW signature, the driver will set the residue to the full transfer length and interpret the data as a CSW. This fixes Bugzilla #86611. Signed-off-by: Alan Stern <[email protected]> CC: Matthew Dharm <[email protected]> Tested-by: Paul Osmialowski <[email protected]> CC: <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2014-11-03usb: Do not allow usb_alloc_streams on unconfigured devicesHans de Goede1-0/+2
This commit fixes the following oops: [10238.622067] scsi host3: uas_eh_bus_reset_handler start [10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10245.779365] usb 3-4: device descriptor read/8, error -110 [10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10250.897603] usb 3-4: device descriptor read/8, error -110 [10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040 [10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140 <snip> [10251.059473] Call Trace: [10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130 [10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0 [10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0 [10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100 [10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70 [10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0 [10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas] [10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas] [10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0 [10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas] [10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110 [10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270 <snip> The problem is the following call sequence (simplified): 1) usb_reset_device 2) usb_reset_and_verify_device 2) hub_port_init 3) hub_port_finish_reset 3) xhci_discover_or_reset_device This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0 4) usb_get_device_descriptor This fails 5) hub_port_init fails 6) usb_reset_and_verify_device fails, does not restore device config 7) uas_post_reset 8) xhci_alloc_streams NULL deref on the free-ed ring This commit fixes this by not allowing usb_alloc_streams to continue if the device is not configured. Note that we do allow usb_free_streams to continue after a (logical) disconnect, as it is necessary to explicitly free the streams at the xhci controller level. Cc: [email protected] Signed-off-by: Hans de Goede <[email protected]> Acked-by: Alan Stern <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2014-11-03cdc-acm: ensure that termios get set when the port is activatedJim Paris1-0/+5
The driver wasn't properly configuring the hardware for the current termios settings under all conditions. Ensure that termios are written to the device when the port is activated. Signed-off-by: Jim Paris <[email protected]> Reviewed-by: Johan Hovold <[email protected]> Acked-by: Oliver Neukum <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2014-11-03USB: cdc-acm: add device id for GW Instek AFG-2225Johan Hovold1-0/+1
Add device-id entry for GW Instek AFG-2225, which has a byte swapped bInterfaceSubClass (0x20). Reported-by: Karl Palsson <[email protected]> Cc: stable <[email protected]> Signed-off-by: Johan Hovold <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2014-11-03Merge branch 'for-linus' of ↵Linus Torvalds3-32/+38
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client Pull ceph fixes from Sage Weil: "There is a GFP flag fix from Mike Christie, an error code fix from Jan, and fixes for two unnecessary allocations (kmalloc and workqueue) from Ilya. All are well tested. Ilya has one other fix on the way but it didn't get tested in time" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: libceph: eliminate unnecessary allocation in process_one_ticket() rbd: Fix error recovery in rbd_obj_read_sync() libceph: use memalloc flags for net IO rbd: use a single workqueue for all devices
2014-11-03Thermal:Remove usless if(!result) before return tzYao Dongdong1-2/+1
result is always zero when comes here. Signed-off-by: Yao Dongdong <[email protected]> Acked-by: Eduardo Valentin <[email protected]> Signed-off-by: Eduardo Valentin <[email protected]>
2014-11-03HID: core: cleanup .claimed field on disconnectBenjamin Tissoires1-0/+1
When a subdriver is rmmod-ed then re-insmod-ed, the hid device is not destroyed as it is owned by the transport layer. So when we re-probed the device, the hid device is assumed to be already claimed, and can lead to page faults if hid-core tries to forward the emitted data to the to-be-created claimed node. Signed-off-by: Benjamin Tissoires <[email protected]> Signed-off-by: Jiri Kosina <[email protected]>
2014-11-03Merge branch 'for-linus' of ↵Linus Torvalds3-1/+3
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k Pull m68k update from Geert Uytterhoeven. Just wiring up the bpf system call. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: m68k: Wire up bpf
2014-11-03Merge tag 'armsoc-for-rc3' of ↵Linus Torvalds9-50/+46
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Olof Johansson: "A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd say. Anyway, most of this are a few defconfig updates. Some for omap to deal with kernel binary size (moving ipv6 to module, etc). A larger one for socfpga that refreshes with some churn, but also turns on a few options that makes the newly-added board in my bootfarm usable for testing. OMAP3 will also now warn when booted with legacy (non-DT) boot protocols, hopefully encouraging those who still care about some of those platforms to submit DT support and report bugs where needed. Nothing stops working though, this is just to warn for future deprecation. Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot hangs, a missing terminting entry in a dt_match array on RealView a MTD fix on OMAP with NAND" [ Obviously missed rc3, will make rc4 instead ;) ] * tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: MAINTAINERS: drop list entry for davinci ARM: OMAP2+: Warn about deprecated legacy booting mode ARM: omap2plus_defconfig: Fix errors with NAND BCH ARM: multi_v7_defconfig: fix support for APQ8084 soc: versatile: Add terminating entry for realview_soc_of_match ARM: ixp4xx: remove compilation warnings in io.h MAINTAINERS: Add Soren as reviewer for Zynq ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in ARM: socfpga_defconfig: Update defconfig for SoCFPGA ARM: pxa: fix hang on startup with DEBUG_LL
2014-11-03[media] sp2: sp2_init() can be staticFengguang Wu1-2/+2
drivers/media/dvb-frontends/sp2.c:269:5: sparse: symbol 'sp2_init' was not declared. Should it be static? drivers/media/dvb-frontends/sp2.c:351:5: sparse: symbol 'sp2_exit' was not declared. Should it be static? Signed-off-by: Fengguang Wu <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2014-11-03sfc: don't BUG_ON efx->max_channels == 0 in probeEdward Cree1-1/+2
efx_ef10_probe() was BUGging out if the BAR2 size was 0. This is unnecessarily violent; instead we should just fail to probe the device. Kept a WARN_ON as this problem indicates a broken or misconfigured NIC. Signed-off-by: Edward Cree <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2014-11-03Merge branch 'ipv6_tunnel_iflink_init'David S. Miller4-30/+11
Steffen Klassert says: ==================== ipv6: Fix iflink setting for ipv6 tunnels The ipv6 tunnels do the dev->iflink setting too early, it gets overwritten by register_netdev(). So set dev->iflink from within a ndo_init function to keep the configured setting. This patchset fixes this for ip6_tunnel, vti6, sit and gre6. ==================== Signed-off-by: David S. Miller <[email protected]>
2014-11-03gre6: Move the setting of dev->iflink into the ndo_init functions.Steffen Klassert1-2/+3
Otherwise it gets overwritten by register_netdev(). Signed-off-by: Steffen Klassert <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2014-11-03sit: Use ipip6_tunnel_init as the ndo_init function.Steffen Klassert1-9/+6
ipip6_tunnel_init() sets the dev->iflink via a call to ipip6_tunnel_bind_dev(). After that, register_netdevice() sets dev->iflink = -1. So we loose the iflink configuration for ipv6 tunnels. Fix this by using ipip6_tunnel_init() as the ndo_init function. Then ipip6_tunnel_init() is called after dev->iflink is set to -1 from register_netdevice(). Signed-off-by: Steffen Klassert <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2014-11-03vti6: Use vti6_dev_init as the ndo_init function.Steffen Klassert1-10/+1
vti6_dev_init() sets the dev->iflink via a call to vti6_link_config(). After that, register_netdevice() sets dev->iflink = -1. So we loose the iflink configuration for vti6 tunnels. Fix this by using vti6_dev_init() as the ndo_init function. Then vti6_dev_init() is called after dev->iflink is set to -1 from register_netdevice(). Signed-off-by: Steffen Klassert <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2014-11-03ip6_tunnel: Use ip6_tnl_dev_init as the ndo_init function.Steffen Klassert1-9/+1
ip6_tnl_dev_init() sets the dev->iflink via a call to ip6_tnl_link_config(). After that, register_netdevice() sets dev->iflink = -1. So we loose the iflink configuration for ipv6 tunnels. Fix this by using ip6_tnl_dev_init() as the ndo_init function. Then ip6_tnl_dev_init() is called after dev->iflink is set to -1 from register_netdevice(). Signed-off-by: Steffen Klassert <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2014-11-03macvtap: Fix csum_start when VLAN tags are presentHerbert Xu1-0/+2
When VLAN is in use in macvtap_put_user, we end up setting csum_start to the wrong place. The result is that the whoever ends up doing the checksum setting will corrupt the packet instead of writing the checksum to the expected location, usually this means writing the checksum with an offset of -4. This patch fixes this by adjusting csum_start when VLAN tags are detected. Fixes: f09e2249c4f5 ("macvtap: restore vlan header on user read") Cc: [email protected] Signed-off-by: Herbert Xu <[email protected]> Cheers, Signed-off-by: David S. Miller <[email protected]>
2014-11-03net: fec: fix suspend broken on multiple MACs silliconsNimrod Andy1-8/+8
On i.MX6SX sdb platform, there has two same enet MACs, after system up, just eth0 is up, and then do suspend/resume test: [ 50.437967] PM: Syncing filesystems ... done. [ 50.476924] Freezing user space processes ... (elapsed 0.005 seconds) done. [ 50.490093] Freezing remaining freezable tasks ... (elapsed 0.004 seconds) done. [ 50.559771] ------------[ cut here ]------------ [ 50.564453] WARNING: CPU: 0 PID: 575 at drivers/clk/clk.c:851 __clk_disable+0x60/0x6c() [ 50.572475] Modules linked in: [ 50.575578] CPU: 0 PID: 575 Comm: sh Not tainted 3.18.0-rc2-next-20141031-00007-gf61135b #21 [ 50.584031] Backtrace: [ 50.586550] [<80011ecc>] (dump_backtrace) from [<8001206c>] (show_stack+0x18/0x1c) [ 50.594136] r6:808a7a54 r5:00000000 r4:00000000 r3:00000000 [ 50.599920] [<80012054>] (show_stack) from [<806ab3c0>] (dump_stack+0x80/0x9c) [ 50.607187] [<806ab340>] (dump_stack) from [<8002a3e8>] (warn_slowpath_common+0x6c/0x8c) [ 50.615294] r5:00000353 r4:00000000 [ 50.618940] [<8002a37c>] (warn_slowpath_common) from [<8002a42c>] (warn_slowpath_null+0x24/0x2c) [ 50.627738] r8:00000000 r7:be144c44 r6:be015600 r5:80070013 r4:be015600 [ 50.634573] [<8002a408>] (warn_slowpath_null) from [<804f8d4c>] (__clk_disable+0x60/0x6c) [ 50.642777] [<804f8cec>] (__clk_disable) from [<804f8e5c>] (clk_disable+0x2c/0x38) [ 50.650359] r4:be015600 r3:00000000 [ 50.654006] [<804f8e30>] (clk_disable) from [<80420ab4>] (fec_enet_clk_enable+0xc4/0x258) [ 50.662196] r5:be3cb620 r4:be3cb000 [ 50.665838] [<804209f0>] (fec_enet_clk_enable) from [<80421178>] (fec_suspend+0x30/0x180) [ 50.674026] r7:be144c44 r6:be144c10 r5:8037f5a4 r4:be3cb000 [ 50.679802] [<80421148>] (fec_suspend) from [<8037f5d8>] (platform_pm_suspend+0x34/0x64) [ 50.687906] r10:00000000 r9:00000000 r8:00000000 r7:be144c44 r6:be144c10 r5:8037f5a4 [ 50.695852] r4:be144c10 r3:80421148 [ 50.699511] [<8037f5a4>] (platform_pm_suspend) from [<8038784c>] (dpm_run_callback.isra.14+0x34/0x6c) [ 50.708764] [<80387818>] (dpm_run_callback.isra.14) from [<80387f00>] (__device_suspend+0x12c/0x2a4) [ 50.717909] r9:8098ec8c r8:80973bec r6:00000002 r5:811c7038 r4:be144c10 [ 50.724746] [<80387dd4>] (__device_suspend) from [<803894fc>] (dpm_suspend+0x64/0x224) [ 50.732675] r8:80973bec r7:be144c10 r6:8098ec24 r5:811c7038 r4:be144cc4 [ 50.739509] [<80389498>] (dpm_suspend) from [<8038999c>] (dpm_suspend_start+0x60/0x68) [ 50.747438] r10:8082fa24 r9:00000000 r8:00000004 r7:00000003 r6:00000000 r5:8116ec80 [ 50.755386] r4:00000002 [ 50.757969] [<8038993c>] (dpm_suspend_start) from [<800679d8>] (suspend_devices_and_enter+0x90/0x3ec) [ 50.767202] r4:00000003 r3:8116eca0 [ 50.770843] [<80067948>] (suspend_devices_and_enter) from [<80067f40>] (pm_suspend+0x20c/0x2a4) [ 50.779553] r8:00000004 r7:00000003 r6:00000000 r5:8116ec8c r4:00000003 [ 50.786394] [<80067d34>] (pm_suspend) from [<80066858>] (state_store+0x70/0xc0) [ 50.793718] r6:8116ec90 r5:00000003 r4:bd88a800 r3:0000006d [ 50.799496] [<800667e8>] (state_store) from [<802b0384>] (kobj_attr_store+0x1c/0x28) [ 50.807251] r10:bd399f78 r8:00000000 r7:bd88a800 r6:bd88a800 r5:00000004 r4:bd085680 [ 50.815219] [<802b0368>] (kobj_attr_store) from [<80153090>] (sysfs_kf_write+0x54/0x58) [ 50.823252] [<8015303c>] (sysfs_kf_write) from [<80151fd8>] (kernfs_fop_write+0xd0/0x194) [ 50.831441] r6:00000004 r5:bd08568c r4:bd085680 r3:8015303c [ 50.837220] [<80151f08>] (kernfs_fop_write) from [<800eddb4>] (vfs_write+0xb8/0x1a8) [ 50.844975] r10:00000000 r9:00000000 r8:00000000 r7:bd399f78 r6:01336408 r5:00000004 [ 50.852924] r4:bc584dc0 [ 50.855505] [<800edcfc>] (vfs_write) from [<800ee0b8>] (SyS_write+0x48/0x88) [ 50.862567] r10:00000000 r8:00000000 r7:01336408 r6:00000004 r5:bc584dc0 r4:bc584dc0 [ 50.870537] [<800ee070>] (SyS_write) from [<8000eb00>] (ret_fast_syscall+0x0/0x48) [ 50.878120] r9:bd398000 r8:8000ecc4 r7:00000004 r6:76f42b48 r5:01336408 r4:00000004 [ 50.885983] ---[ end trace 7545115d752a316a ]--- [ 50.890765] ------------[ cut here ]------------ The root cause is that eth1 is not opened and clock is not enabled, and .suspend() still call .fec_enet_clk_enable() to disable clock. To avoid the broken, let it check network device up status by calling .netif_running() before disable/enable clocks. Signed-off-by: Fugang Duan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2014-11-03Merge branch 'tun-net'David S. Miller1-11/+17
Herbert Xu says: ==================== tun: Fix csum_start and TUN_PKT_STRIP The first patch fixes a serious problem that breaks checksum offload in VMs while the second patch fixes a problem that probably affects no one. ==================== Signed-off-by: David S. Miller <[email protected]>
2014-11-03tun: Fix TUN_PKT_STRIP settingHerbert Xu1-4/+8
We set the flag TUN_PKT_STRIP if the user buffer provided is too small to contain the entire packet plus meta-data. However, this has been broken ever since we added GSO meta-data. VLAN acceleration also has the same problem. This patch fixes this by taking both into account when setting the TUN_PKT_STRIP flag. The fact that this has been broken for six years without anyone realising means that nobody actually uses this flag. Fixes: f43798c27684 ("tun: Allow GSO using virtio_net_hdr") Signed-off-by: Herbert Xu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2014-11-03tun: Fix csum_start with VLAN accelerationHerbert Xu1-7/+9
When VLAN acceleration is in use on the xmit path, we end up setting csum_start to the wrong place. The result is that the whoever ends up doing the checksum setting will corrupt the packet instead of writing the checksum to the expected location, usually this means writing the checksum with an offset of -4. This patch fixes this by adjusting csum_start when VLAN acceleration is detected. Fixes: 6680ec68eff4 ("tuntap: hardware vlan tx support") Cc: [email protected] Signed-off-by: Herbert Xu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2014-11-03ftracetest: Take the first debugfs mount foundSteven Rostedt (Red Hat)1-1/+1
Running ftracetests on a box that mounted debugfs in two locations made the ftracetests fail. This is because the tests uses a grep of debugfs from the /proc/mounts file to find the debugfs mount point, and then appends "/tracing" to that string to get the tracing directory. If the debugfs directory is mounted twice, then that grep will return two answers and appending "/tracing" to a string with two lines will not work. Use "head -1" to only take the first mount point found. Acked-by: Masami Hiramatsu <[email protected]> Signed-off-by: Steven Rostedt <[email protected]>
2014-11-03[media] dvb:tc90522: fix always-false expressionAkihiro Tsukada1-1/+1
Signed-off-by: Akihiro Tsukada <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2014-11-03[media] dvb-core: set default properties of ISDB-SAkihiro Tsukada1-0/+6
Signed-off-by: Akihiro Tsukada <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2014-11-03[media] dvb:tc90522: fix stats reportAkihiro Tsukada1-9/+7
* report the fixed per-transponder symbolrate instead of per-TS ones * add output TS-ID report Signed-off-by: Akihiro Tsukada <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2014-11-03uapi: add missing network related headers to kbuildstephen hemminger1-0/+4
The makefile for sanitizing kernel headers uses the kbuild file to determine which files to do. Several networking related headers were missing. Without these headers iproute2 build would break. Signed-off-by: Stephen Hemminger <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2014-11-03netfilter: nft_reject_bridge: Fix powerpc build errorGuenter Roeck1-0/+1
Fix: net/bridge/netfilter/nft_reject_bridge.c: In function 'nft_reject_br_send_v6_unreach': net/bridge/netfilter/nft_reject_bridge.c:240:3: error: implicit declaration of function 'csum_ipv6_magic' csum_ipv6_magic(&nip6h->saddr, &nip6h->daddr, ^ make[3]: *** [net/bridge/netfilter/nft_reject_bridge.o] Error 1 Seen with powerpc:allmodconfig. Fixes: 523b929d5446 ("netfilter: nft_reject_bridge: don't use IP stack to reject traffic") Cc: Pablo Neira Ayuso <[email protected]> Signed-off-by: Guenter Roeck <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2014-11-03[media] vivid: default to single planar device instancesHans Verkuil2-15/+8
The default used to be that the first vivid device instance was single planar, the second multi planar, the third single planar, etc. However, that turned out to be unexpected and awkward. Change the driver to always default to single planar. Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2014-11-03regulator: s2mpa01: zero-initialize regulator match table arrayJavier Martinez Canillas1-1/+1
The struct of_regulator_match rmatch[] is declared as a non-static local variable so the structure members are not auto-initialized. Initialize the array at declaration time to avoid the structure members values to be indeterminate and have sane defaults instead. Signed-off-by: Javier Martinez Canillas <[email protected]> Signed-off-by: Mark Brown <[email protected]>
2014-11-03regulator: max8660: zero-initialize regulator match table arrayJavier Martinez Canillas1-1/+1
The struct of_regulator_match rmatch[] is declared as a non-static local variable so the structure members are not auto-initialized. Initialize the array at declaration time to avoid the structure members values to be indeterminate and have sane defaults instead. Signed-off-by: Javier Martinez Canillas <[email protected]> Signed-off-by: Mark Brown <[email protected]>
2014-11-03regulator: max77802: zero-initialize regulator match tableJavier Martinez Canillas1-1/+1
The struct of_regulator_match is declared as a non-static local variable so the structure members are not auto-initialized. Initialize the struct at declaration time to avoid the structure members values to be indeterminate and have sane defaults instead. Signed-off-by: Javier Martinez Canillas <[email protected]> Signed-off-by: Mark Brown <[email protected]>
2014-11-03regulator: max77686: zero-initialize regulator match tableJavier Martinez Canillas1-1/+1
The struct of_regulator_match is declared as a non-static local variable so the structure members are not auto-initialized. Initialize the struct at declaration time to avoid the structure members values to be indeterminate and have sane defaults instead. Signed-off-by: Javier Martinez Canillas <[email protected]> Signed-off-by: Mark Brown <[email protected]>
2014-11-03regulator: max1586: zero-initialize regulator match table arrayJavier Martinez Canillas1-1/+1
The struct of_regulator_match rmatch[] is declared as a non-static local variable so the structure members are not auto-initialized. Initialize the array at declaration time to avoid the structure members values to be indeterminate and have sane defaults instead. Signed-off-by: Javier Martinez Canillas <[email protected]> Signed-off-by: Mark Brown <[email protected]>
2014-11-03regulator: max77693: Fix use of uninitialized regulator configKrzysztof Kozlowski1-1/+1
Driver allocated on stack struct regulator_config but didn't initialize it fully. Few fields (driver_data, ena_gpio) were left untouched. This lead to using random ena_gpio values as GPIOs for max77693 regulators. On occasion these values could match real GPIO numbers leading to interfering with other drivers and to unsuccessful enable/disable of regulator. Signed-off-by: Krzysztof Kozlowski <[email protected]> Fixes: 80b022e29bfd ("regulator: max77693: Add max77693 regualtor driver.") Cc: <[email protected]> Signed-off-by: Mark Brown <[email protected]>
2014-11-03iwlwifi: fix RFkill while calibratingEmmanuel Grumbach5-4/+23
If the RFkill interrupt fires while we calibrate, it would make the firmware fail and the driver wasn't able to recover. Change the flow so that the driver will kill the firmware in that case. Since we have now two flows that are calling trans_stop_device (the RFkill interrupt and the op_mode_mvm_start function) - we need to better sync this. Use the STATUS_DEVICE_ENABLED in the pcie transport in an atomic way to achieve this. This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231 CC: <[email protected]> [3.10+] Reviewed-by: Johannes Berg <[email protected]> Reviewed-by: Luciano Coelho <[email protected]> Signed-off-by: Emmanuel Grumbach <[email protected]>
2014-11-03mac80211: fix use-after-free in defragmentationJohannes Berg1-7/+7
Upon receiving the last fragment, all but the first fragment are freed, but the multicast check for statistics at the end of the function refers to the current skb (the last fragment) causing a use-after-free bug. Since multicast frames cannot be fragmented and we check for this early in the function, just modify that check to also do the accounting to fix the issue. Cc: [email protected] Reported-by: Yosef Khyal <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
2014-11-03HID: usbhid: enable always-poll quirk for Elan Touchscreen 0103Adel Gadllah2-0/+2
Yet another device that needs this quirk. Reported-by: Tanguy de Baritault <[email protected]> Signed-off-by: Adel Gadllah <[email protected]> Signed-off-by: Jiri Kosina <[email protected]>
2014-11-03[media] imon: fix other RC type protocol supportUlrich Eckhardt1-1/+2
With kernel 3.17 the imon remote control for device 15c2:0034 does not work anymore, which uses the OTHER protocol. Only the front panel buttons which uses the RC6 protocol are working. Adds the missing comparison for the RC_BIT_OTHER. Cc: [email protected] # for Kernel 3.17 Signed-off-by: Ulrich Eckhardt <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2014-11-03[media] ir-hix5hd2 fix build warningZhangfei Gao1-1/+1
Change CONFIG_PM to CONFIG_PM_SLEEP to solve warning: 'hix5hd2_ir_suspend' & 'hix5hd2_ir_resume' defined but not used Signed-off-by: Zhangfei Gao <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2014-11-03Merge tag 'kvm-s390-20141103' of ↵Paolo Bonzini1-1/+0
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master Fix a build warning in virtio-ccw introduced during the merge window.
2014-11-03KVM: s390: virtio_ccw: remove unused variableSebastian Ott1-1/+0
Fix this warning: drivers/s390/kvm/virtio_ccw.c: In function ‘virtio_ccw_int_handler’: drivers/s390/kvm/virtio_ccw.c:891:24: warning: unused variable ‘drv’ [-Wunused-variable] struct virtio_driver *drv; Signed-off-by: Sebastian Ott <[email protected]> Acked-by: Cornelia Huck <[email protected]> Acked-by: Michael S. Tsirkin <[email protected]> Acked-by: Rusty Russell <[email protected]> Signed-off-by: Cornelia Huck <[email protected]>
2014-11-03USB: opticon: fix non-atomic allocation in write pathJohan Hovold1-1/+1
Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 0d930e51cfe6 ("USB: opticon: Add Opticon OPN2001 write support") Cc: stable <[email protected]> Signed-off-by: Johan Hovold <[email protected]>
2014-11-03USB: kobil_sct: fix non-atomic allocation in write pathJohan Hovold1-2/+3
Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable <[email protected]> Signed-off-by: Johan Hovold <[email protected]>
2014-11-02thermal: exynos: fix IRQ clearing on TMU initializationBartlomiej Zolnierkiewicz4-52/+21
* Factor out code for clearing raised IRQs from exynos_tmu_work() to exynos_tmu_clear_irqs(). * Add a comment about documentation bugs to exynos_tmu_clear_irqs(). [ The documentation for Exynos3250, Exynos4412, Exynos5250 and Exynos5260 incorrectly states that INTCLEAR register has a different placing of bits responsible for FALL IRQs than INTSTAT register. Exynos5420 and Exynos5440 documentation is correct (Exynos4210 doesn't support FALL IRQs at all). ] * Use exynos_tmu_clear_irqs() in exynos_tmu_initialize() instead of open-coded code trying to clear IRQs according to predefined masks. After this change exynos_tmu_initialize() just clears IRQs that are raised like it is already done in exynos_tmu_work(). As a nice side-effect the code now uses the correct offset (16 instead of 12) for bits responsible for clearing FALL IRQs in INTCLEAR register on Exynos3250, Exynos4412 and Exynos5250. * Remove no longer needed intclr_rise_[mask,shift] and intclr_fall_[mask,shift] fields from struct exynos_tmu_registers. * Remove no longer needed defines. This patch has been tested on Exynos4412 and Exynos5420 SoCs. Cc: Amit Daniel Kachhap <[email protected]> Cc: Lukasz Majewski <[email protected]> Cc: Eduardo Valentin <[email protected]> Cc: Zhang Rui <[email protected]> Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]> Acked-by: Kyungmin Park <[email protected]> Signed-off-by: Eduardo Valentin <[email protected]>
2014-11-02thermal: fix multiple disbalanced device node countersVladimir Zapolskiy1-8/+32
Here on function return all temporarily used device nodes shall decrement their usage counter. The problems are found with device nodes allocated by for_each_child_of_node(), of_parse_phandle() and of_find_node_by_name(), fix all problems at once. Signed-off-by: Vladimir Zapolskiy <[email protected]> Cc: [email protected] Cc: Zhang Rui <[email protected]> Cc: Eduardo Valentin <[email protected]> Signed-off-by: Eduardo Valentin <[email protected]>
2014-11-02thermal: rcar: Add binding docs for new R-Car Gen2 SoCsGeert Uytterhoeven1-1/+4
- r8a7792 (R-Car V2H) - r8a7793 (R-Car M2-N) - r8a7794 (R-Car E2) r8a7791 is now called "R-Car M2-W". Signed-off-by: Geert Uytterhoeven <[email protected]> Signed-off-by: Eduardo Valentin <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.