| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fix a commit 8a8158c85e1e ("MIPS: memset.S: EVA & fault support for
small_memset") regression and remove assembly warnings:
arch/mips/lib/memset.S: Assembler messages:
arch/mips/lib/memset.S:243: Warning: Macro instruction expanded into multiple instructions in a branch delay slot
triggering with the CPU_DADDI_WORKAROUNDS option set and this code:
PTR_SUBU a2, t1, a0
jr ra
PTR_ADDIU a2, 1
This is because with that option in place the DADDIU instruction, which
the PTR_ADDIU CPP macro expands to, becomes a GAS macro, which in turn
expands to an LI/DADDU (or actually ADDIU/DADDU) sequence:
13c: 01a4302f dsubu a2,t1,a0
140: 03e00008 jr ra
144: 24010001 li at,1
148: 00c1302d daddu a2,a2,at
...
Correct this by switching off the `noreorder' assembly mode and letting
GAS schedule this jump's delay slot, as there is nothing special about
it that would require manual scheduling. With this change in place
correct code is produced:
13c: 01a4302f dsubu a2,t1,a0
140: 24010001 li at,1
144: 03e00008 jr ra
148: 00c1302d daddu a2,a2,at
...
Signed-off-by: Maciej W. Rozycki <[email protected]>
Signed-off-by: Paul Burton <[email protected]>
Fixes: 8a8158c85e1e ("MIPS: memset.S: EVA & fault support for small_memset")
Patchwork: https://patchwork.linux-mips.org/patch/20833/
Cc: Ralf Baechle <[email protected]>
Cc: [email protected] # 4.17+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix the build on Clear Linux, coping with redundant declarations of
function prototypes in python3 header files by adding
-Wno-redundant-decls to build with PYTHON=python3 (Arnaldo Carvalho de Melo)
- Fixes for processing inline frames in backtraces using DWARF based
unwinding (Milian Wolff)
- Cope with bad DWARF info for function names for inline frames,not
trying to demangle this symbol. Problem reported with rust but
reproduced as well with C++. Problem reported to the libbpf
maintainers (Milian Wolff)
- Fix python export to postgresql and sqlite code (Adrian Hunter)
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Joerg writes:
"IOMMU Fix for Linux v4.19-rc6
One important fix:
- Fix a memory leak with AMD IOMMU when SME is active and a VM
has assigned devices. In that case the complete guest memory
will be leaked without this fix."
* tag 'iommu-fixes-v4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Clear memory encryption mask from physical address
|
|
Paolo writes:
"KVM changes for 4.19-rc7
x86 and PPC bugfixes, mostly introduced in 4.19-rc1."
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: nVMX: fix entry with pending interrupt if APICv is enabled
KVM: VMX: hide flexpriority from guest when disabled at the module level
KVM: VMX: check for existence of secondary exec controls before accessing
KVM: PPC: Book3S HV: Avoid crash from THP collapse during radix page fault
KVM: x86: fix L1TF's MMIO GFN calculation
tools/kvm_stat: cut down decimal places in update interval dialog
KVM: nVMX: Fix emulation of VM_ENTRY_LOAD_BNDCFGS
KVM: x86: Do not use kvm_x86_ops->mpx_supported() directly
KVM: nVMX: Do not expose MPX VMX controls when guest MPX disabled
KVM: x86: never trap MSR_KERNEL_GS_BASE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Herbert writes:
"Crypto Fixes for 4.19
This push fixes the following issues:
- Out-of-bound stack access in qat.
- Illegal schedule in mxs-dcp.
- Memory corruption in chelsio.
- Incorrect pointer computation in caam."
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: qat - Fix KASAN stack-out-of-bounds bug in adf_probe()
crypto: mxs-dcp - Fix wait logic on chan threads
crypto: chelsio - Fix memory corruption in DMA Mapped buffers.
crypto: caam/jr - fix ablkcipher_edesc pointer arithmetic
|
|
Steve writes:
"SMB3 fixes
four small SMB3 fixes: one for stable, the others to address a more
recent regression"
* tag '4.19-rc6-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb3: fix lease break problem introduced by compounding
cifs: only wake the thread for the very last PDU in a compound
cifs: add a warning if we try to to dequeue a deleted mid
smb2: fix missing files in root share directory listing
|
|
Only use the mapped IP to find inline frames, but keep using the
unmapped IP for the callchain cursor. This ensures we properly show the
unmapped IP when displaying a frame we received via the
dso__parse_addr_inlines API for a module which does not contain
sufficient debug symbols to show the srcline.
This is another follow-up to commit 19610184693c ("perf script: Show
virtual addresses instead of offsets").
Signed-off-by: Milian Wolff <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Tested-by: Ravi Bangoria <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Sandipan Das <[email protected]>
Fixes: 19610184693c ("perf script: Show virtual addresses instead of offsets")
Link: http://lkml.kernel.org/r/[email protected]
Link: http://lkml.kernel.org/r/[email protected]
[ Squashed a fix from Milian for a problem reported by Ravi, fixed up space damage ]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The functions vbin_printf() and bstr_printf() are used by trace_printk() to
try to keep the overhead down during printing. trace_printk() uses
vbin_printf() at the time of execution, as it only scans the fmt string to
record the printf values into the buffer, and then uses vbin_printf() to do
the conversions to print the string based on the format and the saved
values in the buffer.
This is an issue for dereferenced pointers, as before commit 841a915d20c7b,
the processing of the pointer could happen some time after the pointer value
was recorded (reading the trace buffer). This means the processing of the
value at a later time could show different results, or even crash the
system, if the pointer no longer existed.
Commit 841a915d20c7b addressed this by processing dereferenced pointers at
the time of execution and save the result in the ring buffer as a string.
The bstr_printf() would then treat these pointers as normal strings, and
print the value. But there was an off-by-one bug here, where after
processing the argument, it move the pointer only "strlen(arg)" which made
the arg pointer not point to the next argument in the ring buffer, but
instead point to the nul character of the last argument. This causes any
values after a dereferenced pointer to be corrupted.
Cc: [email protected]
Fixes: 841a915d20c7b ("vsprintf: Do not have bprintf dereference pointers")
Reported-by: Nikolay Borisov <[email protected]>
Tested-by: Nikolay Borisov <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
When building in ClearLinux using 'make PYTHON=python3' with gcc 8.2.1
it fails with:
GEN /tmp/build/perf/python/perf.so
In file included from /usr/include/python3.7m/Python.h:126,
from /git/linux/tools/perf/util/python.c:2:
/usr/include/python3.7m/import.h:58:24: error: redundant redeclaration of ‘_PyImport_AddModuleObject’ [-Werror=redundant-decls]
PyAPI_FUNC(PyObject *) _PyImport_AddModuleObject(PyObject *, PyObject *);
^~~~~~~~~~~~~~~~~~~~~~~~~
/usr/include/python3.7m/import.h:47:24: note: previous declaration of ‘_PyImport_AddModuleObject’ was here
PyAPI_FUNC(PyObject *) _PyImport_AddModuleObject(PyObject *name,
^~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
error: command 'gcc' failed with exit status 1
And indeed there is a redundant declaration in that Python.h file, one
with parameter names and the other without, so just add
-Wno-error=redundant-decls to the python setup instructions.
Now perf builds with gcc in ClearLinux with the following Dockerfile:
# docker.io/acmel/linux-perf-tools-build-clearlinux:latest
FROM docker.io/clearlinux:latest
MAINTAINER Arnaldo Carvalho de Melo <[email protected]>
RUN swupd update && \
swupd bundle-add sysadmin-basic-dev
RUN mkdir -m 777 -p /git /tmp/build/perf /tmp/build/objtool /tmp/build/linux && \
groupadd -r perfbuilder && \
useradd -m -r -g perfbuilder perfbuilder && \
chown -R perfbuilder.perfbuilder /tmp/build/ /git/
USER perfbuilder
COPY rx_and_build.sh /
ENV EXTRA_MAKE_ARGS=PYTHON=python3
ENTRYPOINT ["/rx_and_build.sh"]
Now to figure out why the build fails with clang, that is present in the
above container as detected by the rx_and_build.sh script:
clang version 6.0.1 (tags/RELEASE_601/final)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /usr/sbin
make: Entering directory '/git/linux/tools/perf'
BUILD: Doing 'make -j4' parallel build
HOSTCC /tmp/build/perf/fixdep.o
HOSTLD /tmp/build/perf/fixdep-in.o
LINK /tmp/build/perf/fixdep
Auto-detecting system features:
... dwarf: [ OFF ]
... dwarf_getlocations: [ OFF ]
... glibc: [ OFF ]
... gtk2: [ OFF ]
... libaudit: [ OFF ]
... libbfd: [ OFF ]
... libelf: [ OFF ]
... libnuma: [ OFF ]
... numa_num_possible_cpus: [ OFF ]
... libperl: [ OFF ]
... libpython: [ OFF ]
... libslang: [ OFF ]
... libcrypto: [ OFF ]
... libunwind: [ OFF ]
... libdw-dwarf-unwind: [ OFF ]
... zlib: [ OFF ]
... lzma: [ OFF ]
... get_cpuid: [ OFF ]
... bpf: [ OFF ]
Makefile.config:331: *** No gnu/libc-version.h found, please install glibc-dev[el]. Stop.
make[1]: *** [Makefile.perf:206: sub-make] Error 2
make: *** [Makefile:70: all] Error 2
make: Leaving directory '/git/linux/tools/perf'
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Thiago Macieira <[email protected]>
Cc: Wang Nan <[email protected]>
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Fix the rxrpc_data_ready() function to pick up all packets and to not miss
any. There are two problems:
(1) The sk_data_ready pointer on the UDP socket is set *after* it is
bound. This means that it's open for business before we're ready to
dequeue packets and there's a tiny window exists in which a packet can
sneak onto the receive queue, but we never know about it.
Fix this by setting the pointers on the socket prior to binding it.
(2) skb_recv_udp() will return an error (such as ENETUNREACH) if there was
an error on the transmission side, even though we set the
sk_error_report hook. Because rxrpc_data_ready() returns immediately
in such a case, it never actually removes its packet from the receive
queue.
Fix this by abstracting out the UDP dequeuing and checksumming into a
separate function that keeps hammering on skb_recv_udp() until it
returns -EAGAIN, passing the packets extracted to the remainder of the
function.
and two potential problems:
(3) It might be possible in some circumstances or in the future for
packets to be being added to the UDP receive queue whilst rxrpc is
running consuming them, so the data_ready() handler might get called
less often than once per packet.
Allow for this by fully draining the queue on each call as (2).
(4) If a packet fails the checksum check, the code currently returns after
discarding the packet without checking for more.
Allow for this by fully draining the queue on each call as (2).
Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <[email protected]>
Acked-by: Paolo Abeni <[email protected]>
|
|
Fix some refs to init_net that should've been changed to the appropriate
network namespace.
Fixes: 2baec2c3f854 ("rxrpc: Support network namespacing")
Signed-off-by: David Howells <[email protected]>
Acked-by: Paolo Abeni <[email protected]>
|
|
With commit 2ea626306810 ("powerpc/topology: Get topology for shared
processors at boot"), kdump kernel on shared LPAR may crash.
The necessary conditions are
- Shared LPAR with at least 2 nodes having memory and CPUs.
- Memory requirement for kdump kernel must be met by the first N-1
nodes where there are at least N nodes with memory and CPUs.
Example numactl of such a machine.
$ numactl -H
available: 5 nodes (0,2,5-7)
node 0 cpus:
node 0 size: 0 MB
node 0 free: 0 MB
node 2 cpus:
node 2 size: 255 MB
node 2 free: 189 MB
node 5 cpus: 24 25 26 27 28 29 30 31
node 5 size: 4095 MB
node 5 free: 4024 MB
node 6 cpus: 0 1 2 3 4 5 6 7 16 17 18 19 20 21 22 23
node 6 size: 6353 MB
node 6 free: 5998 MB
node 7 cpus: 8 9 10 11 12 13 14 15 32 33 34 35 36 37 38 39
node 7 size: 7640 MB
node 7 free: 7164 MB
node distances:
node 0 2 5 6 7
0: 10 40 40 40 40
2: 40 10 40 40 40
5: 40 40 10 40 40
6: 40 40 40 10 20
7: 40 40 40 20 10
Steps to reproduce.
1. Load / start kdump service.
2. Trigger a kdump (for example : echo c > /proc/sysrq-trigger)
When booting a kdump kernel with 2048M:
kexec: Starting switchover sequence.
I'm in purgatory
Using 1TB segments
hash-mmu: Initializing hash mmu with SLB
Linux version 4.19.0-rc5-master+ (srikar@linux-xxu6) (gcc version 4.8.5 (SUSE Linux)) #1 SMP Thu Sep 27 19:45:00 IST 2018
Found initrd at 0xc000000009e70000:0xc00000000ae554b4
Using pSeries machine description
-----------------------------------------------------
ppc64_pft_size = 0x1e
phys_mem_size = 0x88000000
dcache_bsize = 0x80
icache_bsize = 0x80
cpu_features = 0x000000ff8f5d91a7
possible = 0x0000fbffcf5fb1a7
always = 0x0000006f8b5c91a1
cpu_user_features = 0xdc0065c2 0xef000000
mmu_features = 0x7c006001
firmware_features = 0x00000007c45bfc57
htab_hash_mask = 0x7fffff
physical_start = 0x8000000
-----------------------------------------------------
numa: NODE_DATA [mem 0x87d5e300-0x87d67fff]
numa: NODE_DATA(0) on node 6
numa: NODE_DATA [mem 0x87d54600-0x87d5e2ff]
Top of RAM: 0x88000000, Total RAM: 0x88000000
Memory hole size: 0MB
Zone ranges:
DMA [mem 0x0000000000000000-0x0000000087ffffff]
DMA32 empty
Normal empty
Movable zone start for each node
Early memory node ranges
node 6: [mem 0x0000000000000000-0x0000000087ffffff]
Could not find start_pfn for node 0
Initmem setup node 0 [mem 0x0000000000000000-0x0000000000000000]
On node 0 totalpages: 0
Initmem setup node 6 [mem 0x0000000000000000-0x0000000087ffffff]
On node 6 totalpages: 34816
Unable to handle kernel paging request for data at address 0x00000060
Faulting instruction address: 0xc000000008703a54
Oops: Kernel access of bad area, sig: 11 [#1]
LE SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 11 PID: 1 Comm: swapper/11 Not tainted 4.19.0-rc5-master+ #1
NIP: c000000008703a54 LR: c000000008703a38 CTR: 0000000000000000
REGS: c00000000b673440 TRAP: 0380 Not tainted (4.19.0-rc5-master+)
MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 24022022 XER: 20000002
CFAR: c0000000086fc238 IRQMASK: 0
GPR00: c000000008703a38 c00000000b6736c0 c000000009281900 0000000000000000
GPR04: 0000000000000000 0000000000000000 fffffffffffff001 c00000000b660080
GPR08: 0000000000000000 0000000000000000 0000000000000000 0000000000000220
GPR12: 0000000000002200 c000000009e51400 0000000000000000 0000000000000008
GPR16: 0000000000000000 c000000008c152e8 c000000008c152a8 0000000000000000
GPR20: c000000009422fd8 c000000009412fd8 c000000009426040 0000000000000008
GPR24: 0000000000000000 0000000000000000 c000000009168bc8 c000000009168c78
GPR28: c00000000b126410 0000000000000000 c00000000916a0b8 c00000000b126400
NIP [c000000008703a54] bus_add_device+0x84/0x1e0
LR [c000000008703a38] bus_add_device+0x68/0x1e0
Call Trace:
[c00000000b6736c0] [c000000008703a38] bus_add_device+0x68/0x1e0 (unreliable)
[c00000000b673740] [c000000008700194] device_add+0x454/0x7c0
[c00000000b673800] [c00000000872e660] __register_one_node+0xb0/0x240
[c00000000b673860] [c00000000839a6bc] __try_online_node+0x12c/0x180
[c00000000b673900] [c00000000839b978] try_online_node+0x58/0x90
[c00000000b673930] [c0000000080846d8] find_and_online_cpu_nid+0x158/0x190
[c00000000b673a10] [c0000000080848a0] numa_update_cpu_topology+0x190/0x580
[c00000000b673c00] [c000000008d3f2e4] smp_cpus_done+0x94/0x108
[c00000000b673c70] [c000000008d5c00c] smp_init+0x174/0x19c
[c00000000b673d00] [c000000008d346b8] kernel_init_freeable+0x1e0/0x450
[c00000000b673dc0] [c0000000080102e8] kernel_init+0x28/0x160
[c00000000b673e30] [c00000000800b65c] ret_from_kernel_thread+0x5c/0x80
Instruction dump:
60000000 60000000 e89e0020 7fe3fb78 4bff87d5 60000000 7c7d1b79 4082008c
e8bf0050 e93e0098 3b9f0010 2fa50000 <e8690060> 38630018 419e0114 7f84e378
---[ end trace 593577668c2daa65 ]---
However a regular kernel with 4096M (2048 gets reserved for crash
kernel) boots properly.
Unlike regular kernels, which mark all available nodes as online,
kdump kernel only marks just enough nodes as online and marks the rest
as offline at boot. However kdump kernel boots with all available
CPUs. With Commit 2ea626306810 ("powerpc/topology: Get topology for
shared processors at boot"), all CPUs are onlined on their respective
nodes at boot time. try_online_node() tries to online the offline
nodes but fails as all needed subsystems are not yet initialized.
As part of fix, detect and skip early onlining of a offline node.
Fixes: 2ea626306810 ("powerpc/topology: Get topology for shared processors at boot")
Reported-by: Pavithra Prakash <[email protected]>
Signed-off-by: Srikar Dronamraju <[email protected]>
Tested-by: Hari Bathini <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
Recently we implemented show_user_instructions() which dumps the code
around the NIP when a user space process dies with an unhandled
signal. This was modelled on the x86 code, and we even went so far as
to implement the exact same bug, namely that if the user process
crashed with its NIP pointing into the kernel we will dump kernel text
to dmesg. eg:
bad-bctr[2996]: segfault (11) at c000000000010000 nip c000000000010000 lr 12d0b0894 code 1
bad-bctr[2996]: code: fbe10068 7cbe2b78 7c7f1b78 fb610048 38a10028 38810020 fb810050 7f8802a6
bad-bctr[2996]: code: 3860001c f8010080 48242371 60000000 <7c7b1b79> 4082002c e8010080 eb610048
This was discovered on x86 by Jann Horn and fixed in commit
342db04ae712 ("x86/dumpstack: Don't dump kernel memory based on usermode RIP").
Fix it by checking the adjusted NIP value (pc) and number of
instructions against USER_DS, and bail if we fail the check, eg:
bad-bctr[2969]: segfault (11) at c000000000010000 nip c000000000010000 lr 107930894 code 1
bad-bctr[2969]: Bad NIP, not dumping instructions.
Fixes: 88b0fe175735 ("powerpc: Add show_user_instructions()")
Signed-off-by: Michael Ellerman <[email protected]>
|
|
There are platforms which don't provide input clock rate but provide
I2C timing parameters. Commit 3bd4f277274b ("i2c: designware: Call
i2c_dw_clk_rate() only once in i2c_dw_init_master()") causes needless
warning during probe on those platforms since i2c_dw_clk_rate(), which
causes the warning when input clock is unknown, is called even when
there is no need to calculate timing parameters.
Fixes: 3bd4f277274b ("i2c: designware: Call i2c_dw_clk_rate() only once in i2c_dw_init_master()")
Reported-by: Ard Biesheuvel <[email protected]>
Cc: <[email protected]> # 4.19
Signed-off-by: Jarkko Nikula <[email protected]>
Tested-by: Ard Biesheuvel <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
|
|
Before cloning into a file, update the ctime and remove sensitive
attributes like suid, just like we'd do for a regular file write.
Signed-off-by: Darrick J. Wong <[email protected]>
Reviewed-by: Dave Chinner <[email protected]>
Signed-off-by: Dave Chinner <[email protected]>
|
|
When we're reflinking between two files and the destination file range
is well beyond the destination file's EOF marker, zero any posteof
speculative preallocations in the destination file so that we don't
expose stale disk contents. The previous strategy of trying to clear
the preallocations does not work if the destination file has the
PREALLOC flag set.
Uncovered by shared/010.
Reported-by: Zorro Lang <[email protected]>
Bugzilla-id: https://bugzilla.kernel.org/show_bug.cgi?id=201259
Signed-off-by: Darrick J. Wong <[email protected]>
Reviewed-by: Dave Chinner <[email protected]>
Signed-off-by: Dave Chinner <[email protected]>
|
|
Refactor all the reflink preparation steps into a separate helper
that we'll use to land all the upcoming fixes for insufficient input
checks.
This rework also moves the invalidation of the destination range to
the prep function so that it is done before the range is remapped.
This ensures that nobody can access the data in range being remapped
until the remap is complete.
[dgc: fix xfs_reflink_remap_prep() return value and caller check to
handle vfs_clone_file_prep_inodes() returning 0 to mean "nothing to
do". ]
[dgc: make sure length changed by vfs_clone_file_prep_inodes() gets
propagated back to XFS code that does the remapping. ]
Signed-off-by: Darrick J. Wong <[email protected]>
Reviewed-by: Dave Chinner <[email protected]>
Signed-off-by: Dave Chinner <[email protected]>
|
|
Boris Ostrovsky reported a memory leak with device passthrough when SME
is active.
The VFIO driver uses iommu_iova_to_phys() to get the physical address for
an iova. This physical address is later passed into vfio_unmap_unpin() to
unpin the memory. The vfio_unmap_unpin() uses pfn_valid() before unpinning
the memory. The pfn_valid() check was failing because encryption mask was
part of the physical address returned. This resulted in the memory not
being unpinned and therefore leaked after the guest terminates.
The memory encryption mask must be cleared from the physical address in
iommu_iova_to_phys().
Fixes: 2543a786aa25 ("iommu/amd: Allow the AMD IOMMU to work with memory encryption")
Reported-by: Boris Ostrovsky <[email protected]>
Cc: Tom Lendacky <[email protected]>
Cc: Joerg Roedel <[email protected]>
Cc: <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Paolo Bonzini <[email protected]>
Cc: Radim Krčmář <[email protected]>
Cc: [email protected]
Cc: Boris Ostrovsky <[email protected]>
Cc: <[email protected]> # 4.14+
Signed-off-by: Brijesh Singh <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
|
|
When connecting SFP PHY to phylink use the detected interface.
Otherwise, the link fails to come up when the configured 'phy-mode'
differs from the SFP detected mode.
Move most of phylink_connect_phy() into __phylink_connect_phy(), and
leave phylink_connect_phy() as a wrapper. phylink_sfp_connect_phy() can
now pass the SFP detected PHY interface to __phylink_connect_phy().
This fixes 1GB SFP module link up on eth3 of the Macchiatobin board that
is configured in the DT to "2500base-x" phy-mode.
Fixes: 9525ae83959b6 ("phylink: add phylink infrastructure")
Suggested-by: Russell King <[email protected]>
Signed-off-by: Baruch Siach <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
the be2net implementation of .ndo_tunnel_{add,del}() changes the value of
NETIF_F_GSO_UDP_TUNNEL bit in 'features' and 'hw_features', but it forgets
to call netdev_features_change(). Moreover, ethtool setting for that bit
can potentially be reverted after a tunnel is added or removed.
GSO already does software segmentation when 'hw_enc_features' is 0, even
if VXLAN offload is turned on. In addition, commit 096de2f83ebc ("benet:
stricter vxlan offloading check in be_features_check") avoids hardware
segmentation of non-VXLAN tunneled packets, or VXLAN packets having wrong
destination port. So, it's safe to avoid flipping the above feature on
addition/deletion of VXLAN tunnels.
Fixes: 630f4b70567f ("be2net: Export tunnel offloads only when a VxLAN tunnel is created")
Signed-off-by: Davide Caratti <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master
Third set of PPC KVM fixes for 4.19
One patch here, fixing a potential host crash introduced (or at least
exacerbated) by a previous fix for corruption relating to radix guest
page faults and THP operations.
|
|
While we currently grab a runtime PM ref in nouveau's normal connector
detection code, we apparently don't do this for MST. This means if we're
in a scenario where the GPU is suspended and userspace attempts to do a
connector probe on an MSTC connector, the probe will fail entirely due
to the DP aux channel and GPU not being woken up:
[ 316.633489] nouveau 0000:01:00.0: i2c: aux 000a: begin idle timeout ffffffff
[ 316.635713] nouveau 0000:01:00.0: i2c: aux 000a: begin idle timeout ffffffff
[ 316.637785] nouveau 0000:01:00.0: i2c: aux 000a: begin idle timeout ffffffff
...
So, grab a runtime PM ref here.
Signed-off-by: Lyude Paul <[email protected]>
Cc: [email protected]
Reviewed-by: Karol Herbst <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
When we use raw socket as the vhost backend, a packet from virito with
gso offloading information, cannot be sent out in later validaton at
xmit path, as we did not set correct skb->protocol which is further used
for looking up the gso function.
To fix this, we set this field according to virito hdr information.
Fixes: e858fae2b0b8f4 ("virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Jianfeng Tan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.
Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.
Reported-by: Gerhard Wiesinger <[email protected]>
Fixes: c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Load the respective NAT helper module if the flow uses it.
Signed-off-by: Flavio Leitner <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Michael Chan says:
====================
bnxt_en: Misc. bug fixes.
4 small bug fixes related to setting firmware message enables bits, possible
memory leak when probe fails, and ring accouting when RDMA driver is loaded.
Please queue these for -stable as well. Thanks.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
When getting the max rings supported, get the reduced max_irqs
by the ones used by RDMA.
If the number MSIX is the limiting factor, this bug may cause the
max ring count to be higher than it should be when RDMA driver is
loaded and may result in ring allocation failures.
Fixes: 30f529473ec9 ("bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.")
Signed-off-by: Vasundhara Volam <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.
This patch fixes the problem described above.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Duvvuru <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In HWRM_QUEUE_COS2BW_CFG request, enables field should have the bits
set only for the queue ids which are having the valid parameters.
This causes firmware to return error when the TC to hardware CoS queue
mapping is not 1:1 during DCBNL ETS setup.
Fixes: 2e8ef77ee0ff ("bnxt_en: Add TC to hardware QoS queue mapping logic.")
Signed-off-by: Vasundhara Volam <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The enables bit for VNIC was set wrong when calling the HWRM_FUNC_CFG
firmware call to reserve VNICs. This has the effect that the firmware
will keep a large number of VNICs for the PF, and having very few for
VFs. DPDK driver running on the VFs, which requires more VNICs, may not
work properly as a result.
Fixes: 674f50a5b026 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
syzbot was able to trigger rcu stalls by calling write()
with large number of bytes.
Add a cond_resched() in the loop to avoid this.
Link: https://lkml.org/lkml/2018/8/23/1106
Signed-off-by: Eric Dumazet <[email protected]>
Reported-by: [email protected]
Reviewed-by: Paul E. McKenney <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Dave writes:
"amdgpu and two core fixes
Two fixes for amdgpu:
one corrects a use of process->mm
one fix for display code race condition that can result in a crash
Two core fixes:
One for a use-after-free in the leasing code
One for a cma/fbdev crash."
* tag 'drm-fixes-2018-10-05' of git://anongit.freedesktop.org/drm/drm:
drm/amdkfd: Fix incorrect use of process->mm
drm/amd/display: Signal hw_done() after waiting for flip_done()
drm/cma-helper: Fix crash in fbdev error path
drm: fix use-after-free read in drm_mode_create_lease_ioctl()
|
|
into drm-fixes
- Fix an ordering issue in DC with respect to atomic flips that could result
in a crash
- Fix incorrect use of process->mm in KFD
Signed-off-by: Dave Airlie <[email protected]>
From: Alex Deucher <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v4.19-rc7:
- Fix use-after-free in drm_mode_create_lease_ioctl()
- Fix crash in fbdev error path.
Signed-off-by: Dave Airlie <[email protected]>
From: Maarten Lankhorst <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
team's ndo_add_slave() acquires 'team->lock' and later tries to open the
newly enslaved device via dev_open(). This emits a 'NETDEV_UP' event
that causes the VLAN driver to add VLAN 0 on the team device. team's
ndo_vlan_rx_add_vid() will also try to acquire 'team->lock' and
deadlock.
Fix this by checking early at the enslavement function that a team
device is not being enslaved to itself.
A similar check was added to the bond driver in commit 09a89c219baf
("bonding: disallow enslaving a bond to itself").
WARNING: possible recursive locking detected
4.18.0-rc7+ #176 Not tainted
--------------------------------------------
syz-executor4/6391 is trying to acquire lock:
(____ptrval____) (&team->lock){+.+.}, at: team_vlan_rx_add_vid+0x3b/0x1e0 drivers/net/team/team.c:1868
but task is already holding lock:
(____ptrval____) (&team->lock){+.+.}, at: team_add_slave+0xdb/0x1c30 drivers/net/team/team.c:1947
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&team->lock);
lock(&team->lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by syz-executor4/6391:
#0: (____ptrval____) (rtnl_mutex){+.+.}, at: rtnl_lock net/core/rtnetlink.c:77 [inline]
#0: (____ptrval____) (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x412/0xc30 net/core/rtnetlink.c:4662
#1: (____ptrval____) (&team->lock){+.+.}, at: team_add_slave+0xdb/0x1c30 drivers/net/team/team.c:1947
stack backtrace:
CPU: 1 PID: 6391 Comm: syz-executor4 Not tainted 4.18.0-rc7+ #176
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
print_deadlock_bug kernel/locking/lockdep.c:1765 [inline]
check_deadlock kernel/locking/lockdep.c:1809 [inline]
validate_chain kernel/locking/lockdep.c:2405 [inline]
__lock_acquire.cold.64+0x1fb/0x486 kernel/locking/lockdep.c:3435
lock_acquire+0x1e4/0x540 kernel/locking/lockdep.c:3924
__mutex_lock_common kernel/locking/mutex.c:757 [inline]
__mutex_lock+0x176/0x1820 kernel/locking/mutex.c:894
mutex_lock_nested+0x16/0x20 kernel/locking/mutex.c:909
team_vlan_rx_add_vid+0x3b/0x1e0 drivers/net/team/team.c:1868
vlan_add_rx_filter_info+0x14a/0x1d0 net/8021q/vlan_core.c:210
__vlan_vid_add net/8021q/vlan_core.c:278 [inline]
vlan_vid_add+0x63e/0x9d0 net/8021q/vlan_core.c:308
vlan_device_event.cold.12+0x2a/0x2f net/8021q/vlan.c:381
notifier_call_chain+0x180/0x390 kernel/notifier.c:93
__raw_notifier_call_chain kernel/notifier.c:394 [inline]
raw_notifier_call_chain+0x2d/0x40 kernel/notifier.c:401
call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1735
call_netdevice_notifiers net/core/dev.c:1753 [inline]
dev_open+0x173/0x1b0 net/core/dev.c:1433
team_port_add drivers/net/team/team.c:1219 [inline]
team_add_slave+0xa8b/0x1c30 drivers/net/team/team.c:1948
do_set_master+0x1c9/0x220 net/core/rtnetlink.c:2248
do_setlink+0xba4/0x3e10 net/core/rtnetlink.c:2382
rtnl_setlink+0x2a9/0x400 net/core/rtnetlink.c:2636
rtnetlink_rcv_msg+0x46e/0xc30 net/core/rtnetlink.c:4665
netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2455
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4683
netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
netlink_unicast+0x5a0/0x760 net/netlink/af_netlink.c:1343
netlink_sendmsg+0xa18/0xfd0 net/netlink/af_netlink.c:1908
sock_sendmsg_nosec net/socket.c:642 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:652
___sys_sendmsg+0x7fd/0x930 net/socket.c:2126
__sys_sendmsg+0x11d/0x290 net/socket.c:2164
__do_sys_sendmsg net/socket.c:2173 [inline]
__se_sys_sendmsg net/socket.c:2171 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2171
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x456b29
Code: fd b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f9706bf8c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f9706bf96d4 RCX: 0000000000456b29
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000004
RBP: 00000000009300a0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000004d3548 R14: 00000000004c8227 R15: 0000000000000000
Fixes: 87002b03baab ("net: introduce vlan_vid_[add/del] and use them instead of direct [add/kill]_vid ndo calls")
Signed-off-by: Ido Schimmel <[email protected]>
Reported-and-tested-by: [email protected]
Signed-off-by: David S. Miller <[email protected]>
|
|
Cancel pending work before freeing smsc75xx private data structure
during binding. This fixes the following crash in the driver:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: mutex_lock+0x2b/0x3f
<snipped>
Workqueue: events smsc75xx_deferred_multicast_write [smsc75xx]
task: ffff8caa83e85700 task.stack: ffff948b80518000
RIP: 0010:mutex_lock+0x2b/0x3f
<snipped>
Call Trace:
smsc75xx_deferred_multicast_write+0x40/0x1af [smsc75xx]
process_one_work+0x18d/0x2fc
worker_thread+0x1a2/0x269
? pr_cont_work+0x58/0x58
kthread+0xfa/0x10a
? pr_cont_work+0x58/0x58
? rcu_read_unlock_sched_notrace+0x48/0x48
ret_from_fork+0x22/0x40
Signed-off-by: Yu Zhao <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just three small fixes:
* fix use-after-free in regulatory code
* fix rx-mgmt key flag in AP mode (mac80211)
* fix wireless extensions compat code memory leak
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
A cgroup which is already a threaded domain may be converted into a
threaded cgroup if the prerequisite conditions are met. When this
happens, all threaded descendant should also have their ->dom_cgrp
updated to the new threaded domain cgroup. Unfortunately, this
propagation was missing leading to the following failure.
# cd /sys/fs/cgroup/unified
# cat cgroup.subtree_control # show that no controllers are enabled
# mkdir -p mycgrp/a/b/c
# echo threaded > mycgrp/a/b/cgroup.type
At this point, the hierarchy looks as follows:
mycgrp [d]
a [dt]
b [t]
c [inv]
Now let's make node "a" threaded (and thus "mycgrp" s made "domain threaded"):
# echo threaded > mycgrp/a/cgroup.type
By this point, we now have a hierarchy that looks as follows:
mycgrp [dt]
a [t]
b [t]
c [inv]
But, when we try to convert the node "c" from "domain invalid" to
"threaded", we get ENOTSUP on the write():
# echo threaded > mycgrp/a/b/c/cgroup.type
sh: echo: write error: Operation not supported
This patch fixes the problem by
* Moving the opencoded ->dom_cgrp save and restoration in
cgroup_enable_threaded() into cgroup_{save|restore}_control() so
that mulitple cgroups can be handled.
* Updating all threaded descendants' ->dom_cgrp to point to the new
dom_cgrp when enabling threaded mode.
Signed-off-by: Tejun Heo <[email protected]>
Reported-and-tested-by: "Michael Kerrisk (man-pages)" <[email protected]>
Reported-by: Amin Jamali <[email protected]>
Reported-by: Joao De Almeida Pereira <[email protected]>
Link: https://lore.kernel.org/r/CAKgNAkhHYCMn74TCNiMJ=ccLd7DcmXSbvw3CbZ1YREeG7iJM5g@mail.gmail.com
Fixes: 454000adaa2a ("cgroup: introduce cgroup->dom_cgrp and threaded css_set handling")
Cc: [email protected] # v4.14+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Miklos writes:
"overlayfs fixes for 4.19-rc7
This update fixes a couple of regressions in the stacked file update
added in this cycle, as well as some older bugs uncovered by
syzkaller.
There's also one trivial naming change that touches other parts of
the fs subsystem."
* tag 'ovl-fixes-4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix format of setxattr debug
ovl: fix access beyond unterminated strings
ovl: make symbol 'ovl_aops' static
vfs: swap names of {do,vfs}_clone_file_range()
ovl: fix freeze protection bypass in ovl_clone_file_range()
ovl: fix freeze protection bypass in ovl_write_iter()
ovl: fix memory leak on unlink of indexed file
|
|
A reload of the cache's DM table is needed during resize because
otherwise a crash will occur when attempting to access smq policy
entries associated with the portion of the cache that was recently
extended.
The reason is cache-size based data structures in the policy will not be
resized, the only way to safely extend the cache is to allow for a
proper cache policy initialization that occurs when the cache table is
loaded. For example the smq policy's space_init(), init_allocator(),
calc_hotspot_params() must be sized based on the extended cache size.
The fix for this is to disallow cache resizes of this pattern:
1) suspend "cache" target's device
2) resize the fast device used for the cache
3) resume "cache" target's device
Instead, the last step must be a full reload of the cache's DM table.
Fixes: 66a636356 ("dm cache: add stochastic-multi-queue (smq) policy")
Cc: [email protected]
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Commit fd2fa9541 ("dm cache metadata: save in-core policy_hint_size to
on-disk superblock") enabled previously written policy hints to be
used after a cache is reactivated. But in doing so the cache
metadata's hint array was left exposed to out of bounds access because
on resize the metadata's on-disk hint array wasn't ever extended.
Fix this by ignoring that there are no on-disk hints associated with the
newly added cache blocks. An expanded on-disk hint array is later
rewritten upon the next clean shutdown of the cache.
Fixes: fd2fa9541 ("dm cache metadata: save in-core policy_hint_size to on-disk superblock")
Cc: [email protected]
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
If __device_suspend() runs asynchronously (in which case the device
passed to it is in dpm_suspended_list at that point) and it returns
early on an error or pending wakeup, and the power.direct_complete
flag has been set for the device already, the subsequent
device_resume() will be confused by that and it will call
pm_runtime_enable() incorrectly, as runtime PM has not been
disabled for the device by __device_suspend().
To avoid that, clear power.direct_complete if __device_suspend()
is not going to disable runtime PM for the device before returning.
Fixes: aae4518b3124 (PM / sleep: Mechanism to avoid resuming runtime-suspended devices unnecessarily)
Reported-by: Al Cooper <[email protected]>
Tested-by: Al Cooper <[email protected]>
Reviewed-by: Ulf Hansson <[email protected]>
Cc: 3.16+ <[email protected]> # 3.16+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Ido Schimmel says:
====================
mlxsw: Couple of fixes
First patch works around an hardware issue in Spectrum-2 where a field
indicating the event type is always set to the same value. Since there
are only two event types and they are reported using different queues,
we can use the queue number to derive the event type.
Second patch prevents a router interface (RIF) leakage when a VLAN
device is deleted from on top a bridge device.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
In commit 602b74eda813 ("mlxsw: spectrum_switchdev: Do not leak RIFs
when removing bridge") I handled the case where RIFs created for VLAN
devices were not properly cleaned up when their real device (a bridge)
was removed.
However, I forgot to handle the case of the VLAN device itself being
removed. Do so now when the VLAN device is being unlinked from its real
device.
Fixes: 99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Reported-by: Artem Shvorin <[email protected]>
Tested-by: Artem Shvorin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Due to a hardware issue in Spectrum-2, the field event_type of the event
queue element (EQE) has become reserved. It was used to distinguish between
command interface completion events and completion events.
Use queue number to determine event type, as command interface completion
events are always received on EQ0 and mlxsw driver maps completion events
to EQ1.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Russell writes:
"A couple of small ARM fixes from Stefan and Thomas:
- Adding the io_pgetevents syscall
- Fixing a bounds check in pci_ioremap_io()"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8799/1: mm: fix pci_ioremap_io() offset check
ARM: 8787/1: wire up io_pgetevents syscall
|
|
Dave writes:
"drm exynos, tda9950 and intel fixes
3 i915 fixes:
compressed error handling zlib fix
compiler warning cleanup
and a minor code cleanup
2 tda9950:
Two fixes for the HDMI CEC
1 exynos:
A fix required for IOMMU interaction."
* tag 'drm-fixes-2018-10-04' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Handle incomplete Z_FINISH for compressed error states
drm/i915: Avoid compiler warning for maybe unused gu_misc_iir
drm/i915: Do not redefine the has_csr parameter.
drm/exynos: Use selected dma_dev default iommu domain instead of a fake one
drm/i2c: tda9950: set MAX_RETRIES for errors only
drm/i2c: tda9950: fix timeout counter check
|
|
git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Dave writes:
"XFS fixes for 4.19-rc6
Accumlated regression and bug fixes for 4.19-rc6, including:
o make iomap correctly mark dirty pages for sub-page block sizes
o fix regression in handling extent-to-btree format conversion errors
o fix torn log wrap detection for new logs
o various corrupt inode detection fixes
o various delalloc state fixes
o cleanup all the missed transaction cancel cases missed from changes merged
in 4.19-rc1
o fix lockdep false positive on transaction allocation
o fix locking and reference counting on buffer log items"
* tag 'xfs-fixes-for-4.19-rc6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix error handling in xfs_bmap_extents_to_btree
iomap: set page dirty after partial delalloc on mkwrite
xfs: remove invalid log recovery first/last cycle check
xfs: validate inode di_forkoff
xfs: skip delalloc COW blocks in xfs_reflink_end_cow
xfs: don't treat unknown di_flags2 as corruption in scrub
xfs: remove duplicated include from alloc.c
xfs: don't bring in extents in xfs_bmap_punch_delalloc_range
xfs: fix transaction leak in xfs_reflink_allocate_cow()
xfs: avoid lockdep false positives in xfs_trans_alloc
xfs: refactor xfs_buf_log_item reference count handling
xfs: clean up xfs_trans_brelse()
xfs: don't unlock invalidated buf on aborted tx commit
xfs: remove last of unnecessary xfs_defer_cancel() callers
xfs: don't crash the vfs on a garbage inline symlink
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Palmer writes:
"A Single RISC-V Fix for 4.19-rc7
This tag contains a single patch that managed to get lost in the
shuffle, which explains why it's so late. This single line has been
floating around in various patch sets for months, and fixes our DMA32
region."
* tag 'riscv-for-linus-4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISCV: Fix end PFN for low memory
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into fixes
NXP/FSL SoC driver fixes for v4.19 round 2
- Fix crash of qman_portal by deferring its probe if qman is not probed
* tag 'soc-fsl-fix-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qman_portals: defer probe after qman's probe
soc: fsl: qbman: add APIs to retrieve the probing status
soc: fsl: qe: Fix copy/paste bug in ucc_get_tdm_sync_shift()
soc: fsl: qbman: qman: avoid allocating from non existing gen_pool
ARM: dts: BCM63xx: Fix incorrect interrupt specifiers
MAINTAINERS: update the Annapurna Labs maintainer email
ARM: dts: sun8i: drop A64 HDMI PHY fallback compatible from R40 DT
ARM: dts: at91: sama5d2_ptc_ek: fix nand pinctrl
Signed-off-by: Arnd Bergmann <[email protected]>
|