| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Passing large uint32 sockaddr_qrtr.port numbers for port allocation
triggers a warning within idr_alloc() since the port number is cast
to int, and thus interpreted as a negative number. This leads to
the rejection of such valid port numbers in qrtr_port_assign() as
idr_alloc() fails.
To avoid the problem, switch to idr_alloc_u32() instead.
Fixes: bdabad3e363d ("net: Add Qualcomm IPC router")
Reported-by: [email protected]
Signed-off-by: Necip Fazil Yildiran <[email protected]>
Reviewed-by: Dmitry Vyukov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
h1 is initially configured to reach h2 via r1 rather than the
more direct path through r2. If rp_filter is set and inherited
for r2, forwarding fails since the source address of h1 is
reachable from eth0 vs the packet coming to it via r1 and eth1.
Since rp_filter setting affects the test, explicitly reset it.
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
With latest `bpftool prog` command, we observed the following kernel
panic.
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
PGD dfe894067 P4D dfe894067 PUD deb663067 PMD 0
Oops: 0010 [#1] SMP
CPU: 9 PID: 6023 ...
RIP: 0010:0x0
Code: Bad RIP value.
RSP: 0000:ffffc900002b8f18 EFLAGS: 00010286
RAX: ffff8883a405f400 RBX: ffff888e46a6bf00 RCX: 000000008020000c
RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff8883a405f400
RBP: ffff888e46a6bf50 R08: 0000000000000000 R09: ffffffff81129600
R10: ffff8883a405f300 R11: 0000160000000000 R12: 0000000000002710
R13: 000000e9494b690c R14: 0000000000000202 R15: 0000000000000009
FS: 00007fd9187fe700(0000) GS:ffff888e46a40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 0000000de5d33002 CR4: 0000000000360ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
rcu_core+0x1a4/0x440
__do_softirq+0xd3/0x2c8
irq_exit+0x9d/0xa0
smp_apic_timer_interrupt+0x68/0x120
apic_timer_interrupt+0xf/0x20
</IRQ>
RIP: 0033:0x47ce80
Code: Bad RIP value.
RSP: 002b:00007fd9187fba40 EFLAGS: 00000206 ORIG_RAX: ffffffffffffff13
RAX: 0000000000000002 RBX: 00007fd931789160 RCX: 000000000000010c
RDX: 00007fd9308cdfb4 RSI: 00007fd9308cdfb4 RDI: 00007ffedd1ea0a8
RBP: 00007fd9187fbab0 R08: 000000000000000e R09: 000000000000002a
R10: 0000000000480210 R11: 00007fd9187fc570 R12: 00007fd9316cc400
R13: 0000000000000118 R14: 00007fd9308cdfb4 R15: 00007fd9317a9380
After further analysis, the bug is triggered by
Commit eaaacd23910f ("bpf: Add task and task/file iterator targets")
which introduced task_file bpf iterator, which traverses all open file
descriptors for all tasks in the current namespace.
The latest `bpftool prog` calls a task_file bpf program to traverse
all files in the system in order to associate processes with progs/maps, etc.
When traversing files for a given task, rcu read_lock is taken to
access all files in a file_struct. But it used get_file() to grab
a file, which is not right. It is possible file->f_count is 0 and
get_file() will unconditionally increase it.
Later put_file() may cause all kind of issues with the above
as one of sympotoms.
The failure can be reproduced with the following steps in a few seconds:
$ cat t.c
#include <stdio.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
#define N 10000
int fd[N];
int main() {
int i;
for (i = 0; i < N; i++) {
fd[i] = open("./note.txt", 'r');
if (fd[i] < 0) {
fprintf(stderr, "failed\n");
return -1;
}
}
for (i = 0; i < N; i++)
close(fd[i]);
return 0;
}
$ gcc -O2 t.c
$ cat run.sh
#/bin/bash
for i in {1..100}
do
while true; do ./a.out; done &
done
$ ./run.sh
$ while true; do bpftool prog >& /dev/null; done
This patch used get_file_rcu() which only grabs a file if the
file->f_count is not zero. This is to ensure the file pointer
is always valid. The above reproducer did not fail for more
than 30 minutes.
Fixes: eaaacd23910f ("bpf: Add task and task/file iterator targets")
Suggested-by: Josef Bacik <[email protected]>
Signed-off-by: Yonghong Song <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
Reviewed-by: Josef Bacik <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
WeiXiong Liao noted to me offlist that his preference for email address
had changed and that he'd like it updated in the mailmap so people
discussing pstore/blk would be able to reach him.
Cc: WeiXiong Liao <[email protected]>
Signed-off-by: Kees Cook <[email protected]>
|
|
Several names had been recently appended (instead of inserted). While
git-shortlog doesn't need this file to be sorted, it helps humans to
keep it organized this way. Sort the entire file (which includes some
minor shuffling for dictionary order).
Done with the following commands:
grep -E '^(#|$)' .mailmap > .mailmap.head
grep -Ev '^(#|$)' .mailmap > .mailmap.body
sort -f .mailmap.body > .mailmap.body.sort
cat .mailmap.head .mailmap.body.sort > .mailmap
rm .mailmap.head .mailmap.body.sort
Signed-off-by: Kees Cook <[email protected]>
|
|
Currently invalid CPU addresses are not being sanity checked resulting in
SATA setup failure on a SynQuacer SC2A11 development machine. The original
check was removed by and earlier commit, so add a sanity check back in
to avoid this regression.
Fixes: 7a8b64d17e35 ("of/address: use range parser for of_dma_get_range")
Signed-off-by: Colin Ian King <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Rob Herring <[email protected]>
|
|
See the SDM, volume 3, section 4.4.1:
If PAE paging would be in use following an execution of MOV to CR0 or
MOV to CR4 (see Section 4.1.1) and the instruction is modifying any of
CR0.CD, CR0.NW, CR0.PG, CR4.PAE, CR4.PGE, CR4.PSE, or CR4.SMEP; then
the PDPTEs are loaded from the address in CR3.
Fixes: b9baba8614890 ("KVM, pkeys: expose CPUID/CR4 to guest")
Cc: Huaitong Han <[email protected]>
Signed-off-by: Jim Mattson <[email protected]>
Reviewed-by: Peter Shier <[email protected]>
Reviewed-by: Oliver Upton <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
See the SDM, volume 3, section 4.4.1:
If PAE paging would be in use following an execution of MOV to CR0 or
MOV to CR4 (see Section 4.1.1) and the instruction is modifying any of
CR0.CD, CR0.NW, CR0.PG, CR4.PAE, CR4.PGE, CR4.PSE, or CR4.SMEP; then
the PDPTEs are loaded from the address in CR3.
Fixes: 0be0226f07d14 ("KVM: MMU: fix SMAP virtualization")
Cc: Xiao Guangrong <[email protected]>
Signed-off-by: Jim Mattson <[email protected]>
Reviewed-by: Peter Shier <[email protected]>
Reviewed-by: Oliver Upton <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
The PK bit of the error code is computed dynamically in permission_fault
and therefore need not be passed to gva_to_gpa: only the access bits
(fetch, user, write) need to be passed down.
Not doing so causes a splat in the pku test:
WARNING: CPU: 25 PID: 5465 at arch/x86/kvm/mmu.h:197 paging64_walk_addr_generic+0x594/0x750 [kvm]
Hardware name: Intel Corporation WilsonCity/WilsonCity, BIOS WLYDCRB1.SYS.0014.D62.2001092233 01/09/2020
RIP: 0010:paging64_walk_addr_generic+0x594/0x750 [kvm]
Code: <0f> 0b e9 db fe ff ff 44 8b 43 04 4c 89 6c 24 30 8b 13 41 39 d0 89
RSP: 0018:ff53778fc623fb60 EFLAGS: 00010202
RAX: 0000000000000001 RBX: ff53778fc623fbf0 RCX: 0000000000000007
RDX: 0000000000000001 RSI: 0000000000000002 RDI: ff4501efba818000
RBP: 0000000000000020 R08: 0000000000000005 R09: 00000000004000e7
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000007
R13: ff4501efba818388 R14: 10000000004000e7 R15: 0000000000000000
FS: 00007f2dcf31a700(0000) GS:ff4501f1c8040000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000001dea475005 CR4: 0000000000763ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
paging64_gva_to_gpa+0x3f/0xb0 [kvm]
kvm_fixup_and_inject_pf_error+0x48/0xa0 [kvm]
handle_exception_nmi+0x4fc/0x5b0 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x911/0x1c10 [kvm]
kvm_vcpu_ioctl+0x23e/0x5d0 [kvm]
ksys_ioctl+0x92/0xb0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x3e/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace d17eb998aee991da ]---
Reported-by: Sean Christopherson <[email protected]>
Fixes: 897861479c064 ("KVM: x86: Add helper functions for illegal GPA checking and page fault injection")
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
IA-64 is special and treats pgd_offset_k() differently to pgd_offset(),
using different formulae to calculate the indices into the kernel and user
PGDs. The index into the user PGDs takes into account the region number,
but the index into the kernel (init_mm) PGD always assumes a predefined
kernel region number. Commit 974b9b2c68f3 ("mm: consolidate pte_index() and
pte_offset_*() definitions") made IA-64 use a generic pgd_offset_k() which
incorrectly used pgd_index() for kernel page tables. As a result, the
index into the kernel PGD was going out of bounds and the kernel hung
during early boot.
Allow overrides of pgd_offset_k() and override it on IA-64 with the old
implementation that will correctly index the kernel PGD.
Fixes: 974b9b2c68f3 ("mm: consolidate pte_index() and pte_offset_*() definitions")
Reported-by: John Paul Adrian Glaubitz <[email protected]>
Signed-off-by: Jessica Clarke <[email protected]>
Tested-by: John Paul Adrian Glaubitz <[email protected]>
Acked-by: Tony Luck <[email protected]>
Signed-off-by: Mike Rapoport <[email protected]>
|
|
This reverts commit f8414a8d886b613b90d9fdf7cda6feea313b1069.
eth_type_trans() does the necessary pull on the skb.
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix a kernel-doc warning for the pcs_config() function prototype:
../include/linux/phylink.h:406: warning: Excess function parameter 'permit_pause_to_mac' description in 'pcs_config'
Fixes: 7137e18f6f88 ("net: phylink: add struct phylink_pcs")
Signed-off-by: Randy Dunlap <[email protected]>
Cc: Russell King <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: [email protected]
Signed-off-by: David S. Miller <[email protected]>
|
|
Some devices have broken extension unit where getting current value
doesn't work. Attempt that once when creating mixer control for it. If
it fails, just ignore it, so that it won't cripple the device entirely
(and/or make the error floods).
Signed-off-by: Tom Yan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
If debug_regs.c is built with newer binutils, the resulting binary is "optimized"
by the assembler:
asm volatile("ss_start: "
"xor %%rax,%%rax\n\t"
"cpuid\n\t"
"movl $0x1a0,%%ecx\n\t"
"rdmsr\n\t"
: : : "rax", "ecx");
is translated to :
000000000040194e <ss_start>:
40194e: 31 c0 xor %eax,%eax <----- rax->eax?
401950: 0f a2 cpuid
401952: b9 a0 01 00 00 mov $0x1a0,%ecx
401957: 0f 32 rdmsr
As you can see rax is replaced with eax in target binary code.
This causes a difference is the length of xor instruction (2 Byte vs 3 Byte),
and makes the hard-coded instruction length check fail:
/* Instruction lengths starting at ss_start */
int ss_size[4] = {
3, /* xor */ <-------- 2 or 3?
2, /* cpuid */
5, /* mov */
2, /* rdmsr */
};
Encode the shorter version directly and, while at it, fix the "clobbers"
of the asm.
Cc: [email protected]
Signed-off-by: Yang Weijiang <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
The vfio_iommu_replay() function does not currently unwind on error,
yet it does pin pages, perform IOMMU mapping, and modify the vfio_dma
structure to indicate IOMMU mapping. The IOMMU mappings are torn down
when the domain is destroyed, but the other actions go on to cause
trouble later. For example, the iommu->domain_list can be empty if we
only have a non-IOMMU backed mdev attached. We don't currently check
if the list is empty before getting the first entry in the list, which
leads to a bogus domain pointer. If a vfio_dma entry is erroneously
marked as iommu_mapped, we'll attempt to use that bogus pointer to
retrieve the existing physical page addresses.
This is the scenario that uncovered this issue, attempting to hot-add
a vfio-pci device to a container with an existing mdev device and DMA
mappings, one of which could not be pinned, causing a failure adding
the new group to the existing container and setting the conditions
for a subsequent attempt to explode.
To resolve this, we can first check if the domain_list is empty so
that we can reject replay of a bogus domain, should we ever encounter
this inconsistent state again in the future. The real fix though is
to add the necessary unwind support, which means cleaning up the
current pinning if an IOMMU mapping fails, then walking back through
the r-b tree of DMA entries, reading from the IOMMU which ranges are
mapped, and unmapping and unpinning those ranges. To be able to do
this, we also defer marking the DMA entry as IOMMU mapped until all
entries are processed, in order to allow the unwind to know the
disposition of each entry.
Fixes: a54eb55045ae ("vfio iommu type1: Add support for mediated devices")
Reported-by: Zhiyi Guo <[email protected]>
Tested-by: Zhiyi Guo <[email protected]>
Reviewed-by: Cornelia Huck <[email protected]>
Signed-off-by: Alex Williamson <[email protected]>
|
|
A down_read on memory_lock is held when performing read/write accesses
to MMIO BAR space, including across the copy_to/from_user() callouts
which may fault. If the user buffer for these copies resides in an
mmap of device MMIO space, the mmap fault handler will acquire a
recursive read-lock on memory_lock. Avoid this by reducing the lock
granularity. Sequential accesses requiring multiple ioread/iowrite
cycles are expected to be rare, therefore typical accesses should not
see additional overhead.
VGA MMIO accesses are expected to be non-fatal regardless of the PCI
memory enable bit to allow legacy probing, this behavior remains with
a comment added. ioeventfds are now included in memory access testing,
with writes dropped while memory space is disabled.
Fixes: abafbc551fdd ("vfio-pci: Invalidate mmaps and block MMIO access on disabled memory")
Reported-by: Zhiyi Guo <[email protected]>
Tested-by: Zhiyi Guo <[email protected]>
Reviewed-by: Cornelia Huck <[email protected]>
Signed-off-by: Alex Williamson <[email protected]>
|
|
This -Wsign-compare compiler warning can be very noisy
and most of the suggested conversions are unnecessary.
Make the warning W=3 so it's described under the
"can most likely be ignored" block.
Signed-off-by: Joe Perches <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Impose a limit on the number of watches that a user can hold so that
they can't use this mechanism to fill up all the available memory.
This is done by putting a counter in user_struct that's incremented when
a watch is allocated and decreased when it is released. If the number
exceeds the RLIMIT_NOFILE limit, the watch is rejected with EAGAIN.
This can be tested by the following means:
(1) Create a watch queue and attach it to fd 5 in the program given - in
this case, bash:
keyctl watch_session /tmp/nlog /tmp/gclog 5 bash
(2) In the shell, set the maximum number of files to, say, 99:
ulimit -n 99
(3) Add 200 keyrings:
for ((i=0; i<200; i++)); do keyctl newring a$i @s || break; done
(4) Try to watch all of the keyrings:
for ((i=0; i<200; i++)); do echo $i; keyctl watch_add 5 %:a$i || break; done
This should fail when the number of watches belonging to the user hits
99.
(5) Remove all the keyrings and all of those watches should go away:
for ((i=0; i<200; i++)); do keyctl unlink %:a$i; done
(6) Kill off the watch queue by exiting the shell spawned by
watch_session.
Fixes: c73be61cede5 ("pipe: Add general notification queue support")
Reported-by: Linus Torvalds <[email protected]>
Signed-off-by: David Howells <[email protected]>
Reviewed-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Commit ("03fd42d458fb powerpc/fixmap: Fix FIX_EARLY_DEBUG_BASE when
page size is 256k") reworked the setup of the early debug area and
mistakenly replaced 128 * 1024 by SZ_128.
Change to SZ_128K to restore the original 128 kbytes size of the area.
Fixes: 03fd42d458fb ("powerpc/fixmap: Fix FIX_EARLY_DEBUG_BASE when page size is 256k")
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/996184974d674ff984643778cf1cdd7fe58cc065.1597644194.git.christophe.leroy@csgroup.eu
|
|
IS_ENABLED() instead of #ifdef still requires variable declaration.
In this specific case, default_uamor is declared in asm/pkeys.h which
is only included if PPC_MEM_KEYS is enabled.
arch/powerpc/mm/book3s64/hash_utils.c: In function ‘hash__early_init_mmu_secondary’:
arch/powerpc/mm/book3s64/hash_utils.c:1119:21: error: ‘default_uamor’ undeclared (first use in this function)
1119 | mtspr(SPRN_UAMOR, default_uamor);
| ^~~~~~~~~~~~~
Fixes: 6553fb799f60 ("powerpc/pkeys: Fix boot failures with Nemo board (A-EON AmigaOne X1000)")
Signed-off-by: Aneesh Kumar K.V <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
When power_up_sst() fails, stream needs to be freed
just like when try_module_get() fails. However, current
code is returning directly and ends up leaking memory.
Fixes: 0121327c1a68b ("ASoC: Intel: mfld-pcm: add control for powering up/down dsp")
Signed-off-by: Dinghao Liu <[email protected]>
Acked-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The driver supports WM1811, WM8994, WM8958 devices but according to
documentation and the regmap definitions the WM8958_DSP2_* registers
are only available on WM8958. In current code these registers are
being accessed as if they were available on all the three chips.
When starting playback on WM1811 CODEC multiple errors like:
"wm8994-codec wm8994-codec: ASoC: error at soc_component_read_no_lock on wm8994-codec: -5"
can be seen, which is caused by attempts to read an unavailable
WM8958_DSP2_PROGRAM register. The issue has been uncovered by recent
commit "e2329ee ASoC: soc-component: add soc_component_err()".
This patch adds a check in wm8958_aif_ev() callback so the DSP2 handling
is only done for WM8958.
Signed-off-by: Sylwester Nawrocki <[email protected]>
Acked-by: Charles Keepax <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
For some reason interrupt set and clear register offsets are
not set correctly.
This patch corrects them!
Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Signed-off-by: Srinivas Kandagatla <[email protected]>
Tested-by: Stephan Gerhold <[email protected]>
Reviewed-by: Stephan Gerhold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The ADC2 and DAC2 are not available on WM1811 device. This patch moves
the ADC2, DAC2 VU bitfields to a separate array so we can skip accessing
them and avoid unreadable register access on WM1811.
This allows to get rid of warnings during boot like:
wm8994-codec: ASoC: error at soc_component_read_no_lock on wm8994-codec: -5
Signed-off-by: Sylwester Nawrocki <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Currently there are four places in which a PCI function is scanned
and made available to drivers:
1. In pci_scan_root_bus() as part of the initial zbus
creation.
2. In zpci_bus_add_devices() when registering
a device in configured state on a zbus that has already been
scanned.
3. When a function is already known to zPCI (in reserved/standby state)
and configuration is triggered through firmware by PEC 0x301.
4. When a device is already known to zPCI (in standby/reserved state)
and configuration is triggered from within Linux using
enable_slot().
The PF/VF linking step and setting of pdev->is_virtfn introduced with
commit e5794cf1a270 ("s390/pci: create links between PFs and VFs") was
only triggered for the second case, which is where VFs created through
sriov_numvfs usually land. However unlike some other platforms but like
POWER VFs can be individually enabled/disabled through
/sys/bus/pci/slots.
Fix this by doing VF setup as part of pcibios_bus_add_device() which is
called in all of the above cases.
Finally to remove the PF/VF links call the common code
pci_iov_remove_virtfn() function to remove linked VFs.
This takes care of the necessary sysfs cleanup.
Fixes: e5794cf1a270 ("s390/pci: create links between PFs and VFs")
Cc: <[email protected]> # 5.8: 2f0230b2f2d5: s390/pci: re-introduce zpci_remove_device()
Cc: <[email protected]> # 5.8
Acked-by: Pierre Morel <[email protected]>
Signed-off-by: Niklas Schnelle <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
|
|
For fixing the PF to VF link removal we need to perform some action on
every removal of a zdev from the common PCI subsystem.
So in preparation re-introduce zpci_remove_device() and use that instead
of directly calling the common code functions. This was actually still
declared from earlier code but no longer implemented.
Reviewed-by: Pierre Morel <[email protected]>
Signed-off-by: Niklas Schnelle <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
|
|
We were missing the pci_dev_put() for candidate PFs. Furhtermore in
discussion with upstream it turns out that somewhat counterintuitively
some common code, in particular the vfio-pci driver, assumes that
pdev->is_virtfn always implies that pdev->physfn is set, i.e. that VFs
are always linked.
While POWER does seem to set pdev->is_virtfn even for unlinked functions
(see comments in arch/powerpc/kernel/eeh.c:eeh_debugfs_break_device())
for now just be safe and only set pdev->is_virtfn on linking.
Also make sure that we only search for parent PFs if the zbus is
multifunction and we thus know the devfn values supplied by firmware
come from the RID.
Fixes: e5794cf1a270 ("s390/pci: create links between PFs and VFs")
Cc: <[email protected]> # 5.8
Reviewed-by: Pierre Morel <[email protected]>
Signed-off-by: Niklas Schnelle <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
|
|
The key member of the runtime instrumentation control block contains
only the access key, not the complete storage key. Therefore the value
must be shifted by four bits. Since existing user space does not
necessarily query and set the access key correctly, just ignore the
user space provided key and use the correct one.
Note: this is only relevant for debugging purposes in case somebody
compiles a kernel with a default storage access key set to a value not
equal to zero.
Fixes: 262832bc5acd ("s390/ptrace: add runtime instrumention register get/set")
Reported-by: Claudio Imbrenda <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
|
|
The key member of the runtime instrumentation control block contains
only the access key, not the complete storage key. Therefore the value
must be shifted by four bits.
Note: this is only relevant for debugging purposes in case somebody
compiles a kernel with a default storage access key set to a value not
equal to zero.
Fixes: e4b8b3f33fca ("s390: add support for runtime instrumentation")
Reported-by: Claudio Imbrenda <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
|
|
A configuration request event may be stale, that is the event
may reference a zdev which was already configured.
This can happen when a hotplug happens during boot such that
the device is discovered and configured in the initial clp_list_pci(),
then after initialization we enable events and process
the original configuration request which additionally still contains
the old disabled function handle leading to a failure during device
enablement and subsequent I/O lockout.
Fix this by restoring the check that the device to be configured is in
standby which was removed in commit f606b3ef47c9 ("s390/pci: adapt events
for zbus").
This check does not need serialization as we only enable the events after
zPCI has fully initialized, which includes the initial clp_list_pci(),
rescan only does updates and events are serialized with respect to each
other.
Fixes: f606b3ef47c9 ("s390/pci: adapt events for zbus")
Cc: <[email protected]> # 5.8
Reported-by: Shalini Chellathurai Saroja <[email protected]>
Tested-by: Shalini Chellathurai Saroja <[email protected]>
Acked-by: Pierre Morel <[email protected]>
Signed-off-by: Niklas Schnelle <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
|
|
The scanning through subchannels during the time of an event could
take significant amount of time in case of platforms with lots of
known subchannels. This might result in higher scheduling latencies
for other tasks especially on systems with a single CPU. Add
cond_resched() call, as the loop in slow_eval_known_fn() can be
executed for a longer duration.
Reviewed-by: Peter Oberparleiter <[email protected]>
Signed-off-by: Vineeth Vijayan <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
|
|
The very quiet and distorted headphone output bug that afflicted my
Samsung Notebook 9 is appearing in many other Samsung laptops. Expose
the quirk which fixed my laptop as a model so other users can try it.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207423
Signed-off-by: Mike Pozulp <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
As the recent fix addressed the channel swap problem more properly,
update the comment as well.
Fixes: 1b7ecc241a67 ("ALSA: usb-audio: work around streaming quirk for MacroSilicon MS2109")
Signed-off-by: Hector Martin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
We get the opp_table pointer at the top of the function and so we should
put the pointer at the end of the function like all other exit paths
from this function do.
Cc: v5.8+ <[email protected]> # v5.8+
Fixes: b00e667a6d8b ("opp: Remove bandwidth votes when target_freq is zero")
Reviewed-by: Rajendra Nayak <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
[ Viresh: Split the patch into two ]
Signed-off-by: Viresh Kumar <[email protected]>
|
|
We get the opp_table pointer at the top of the function and so we should
put the pointer at the end of the function like all other exit paths
from this function do.
Cc: v5.7+ <[email protected]> # v5.7+
Fixes: aca48b61f963 ("opp: Manage empty OPP tables with clk handle")
Reviewed-by: Rajendra Nayak <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
[ Viresh: Split the patch into two ]
Signed-off-by: Viresh Kumar <[email protected]>
|
|
__machine_check_early_realmode_p*() are currently declared as extern
in cputable.c and because of this when compiled with "C=1" (which
enables semantic checker) produces these warnings.
CHECK arch/powerpc/kernel/mce_power.c
arch/powerpc/kernel/mce_power.c:709:6: warning: symbol '__machine_check_early_realmode_p7' was not declared. Should it be static?
arch/powerpc/kernel/mce_power.c:717:6: warning: symbol '__machine_check_early_realmode_p8' was not declared. Should it be static?
arch/powerpc/kernel/mce_power.c:722:6: warning: symbol '__machine_check_early_realmode_p9' was not declared. Should it be static?
arch/powerpc/kernel/mce_power.c:740:6: warning: symbol '__machine_check_early_realmode_p10' was not declared. Should it be static?
Patch here moves the declaration to asm/mce.h and includes the same in
cputable.c
Fixes: ae744f3432d3 ("powerpc/book3s: Flush SLB/TLBs if we get SLB/TLB machine check errors on power8")
Fixes: 7b9f71f974a1 ("powerpc/64s: POWER9 machine check handler")
Signed-off-by: Madhavan Srinivasan <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This fix wasn't correct: When this function is invoked from the
retransmission worker, the iterator contains garbage and resetting
it causes a crash.
As the work queue should not be performance critical also zero the
msghdr struct.
Fixes: 35759383133f64d "(mptcp: sendmsg: reset iter on error)"
Signed-off-by: Florian Westphal <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add a raw mode cputable entry for POWER10. Copies most of the fields
from commit a3ea40d5c736 ("powerpc: Add POWER10 architected mode")
except for oprofile_cpu_type, machine_check_early, pvr_mask and
pvr_mask fields. On bare metal systems we use DT CPU features, which
doesn't need a cputable entry. But in VMs we still rely on the raw
cputable entry to set the correct values for the PMU related fields.
Fixes: a3ea40d5c736 ("powerpc: Add POWER10 architected mode")
Signed-off-by: Madhavan Srinivasan <[email protected]>
[mpe: Reorder vs cleanup patch and add Fixes tag]
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
It is possible to trigger this WARN_ON from user space by triggering a
devlink snapshot with an ID which already exists. We don't need both
-EEXISTS being reported and spamming the kernel log.
Signed-off-by: Andrew Lunn <[email protected]>
Tested-by: Chris Healy <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When using ipv6_dev_find() in one module, it requires ipv6 not to
work as a module. Otherwise, this error occurs in build:
undefined reference to `ipv6_dev_find'.
So fix it by adding "depends on IPV6 || IPV6=n" to tipc/Kconfig,
as it does in sctp/Kconfig.
Fixes: 5a6f6f579178 ("tipc: set ub->ifindex for local ipv6 address")
Reported-by: kernel test robot <[email protected]>
Acked-by: Randy Dunlap <[email protected]>
Signed-off-by: Xin Long <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
__tipc_nl_compat_dumpit() has two callers, and it expects them to
pass a valid nlmsghdr via arg->data. This header is artificial and
crafted just for __tipc_nl_compat_dumpit().
tipc_nl_compat_publ_dump() does so by putting a genlmsghdr as well
as some nested attribute, TIPC_NLA_SOCK. But the other caller
tipc_nl_compat_dumpit() does not, this leaves arg->data uninitialized
on this call path.
Fix this by just adding a similar nlmsghdr without any payload in
tipc_nl_compat_dumpit().
This bug exists since day 1, but the recent commit 6ea67769ff33
("net: tipc: prepare attrs in __tipc_nl_compat_dumpit()") makes it
easier to appear.
Reported-and-tested-by: [email protected]
Fixes: d0796d1ef63d ("tipc: convert legacy nl bearer dump to nl compat")
Cc: Jon Maloy <[email protected]>
Cc: Ying Xue <[email protected]>
Cc: Richard Alpe <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Acked-by: Ying Xue <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Include capability flag PERF_PMU_CAP_EXTENDED_REGS for power10 and
expose MMCR3, SIER2, SIER3 registers as part of extended regs. Also
introduce PERF_REG_PMU_MASK_31 to define extended mask value at
runtime for power10.
Suggested-by: Ryan Grimm <[email protected]>
Signed-off-by: Athira Rajeev <[email protected]>
Tested-by: Nageswara R Sastry <[email protected]>
Reviewed-by: Kajol Jain <[email protected]>
Reviewed-and-tested-by: Ravi Bangoria <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add support for perf extended register capability in powerpc. The
capability flag PERF_PMU_CAP_EXTENDED_REGS, is used to indicate the
PMU which support extended registers. The generic code define the mask
of extended registers as 0 for non supported architectures.
Patch adds extended regs support for power9 platform by exposing
MMCR0, MMCR1 and MMCR2 registers.
REG_RESERVED mask needs update to include extended regs.
PERF_REG_EXTENDED_MASK, contains mask value of the supported
registers, is defined at runtime in the kernel based on platform since
the supported registers may differ from one processor version to
another and hence the MASK value.
With the patch:
available registers: r0 r1 r2 r3 r4 r5 r6 r7 r8 r9 r10 r11
r12 r13 r14 r15 r16 r17 r18 r19 r20 r21 r22 r23 r24 r25 r26
r27 r28 r29 r30 r31 nip msr orig_r3 ctr link xer ccr softe
trap dar dsisr sier mmcra mmcr0 mmcr1 mmcr2
PERF_RECORD_SAMPLE(IP, 0x1): 4784/4784: 0 period: 1 addr: 0
... intr regs: mask 0xffffffffffff ABI 64-bit
.... r0 0xc00000000012b77c
.... r1 0xc000003fe5e03930
.... r2 0xc000000001b0e000
.... r3 0xc000003fdcddf800
.... r4 0xc000003fc7880000
.... r5 0x9c422724be
.... r6 0xc000003fe5e03908
.... r7 0xffffff63bddc8706
.... r8 0x9e4
.... r9 0x0
.... r10 0x1
.... r11 0x0
.... r12 0xc0000000001299c0
.... r13 0xc000003ffffc4800
.... r14 0x0
.... r15 0x7fffdd8b8b00
.... r16 0x0
.... r17 0x7fffdd8be6b8
.... r18 0x7e7076607730
.... r19 0x2f
.... r20 0xc00000001fc26c68
.... r21 0xc0002041e4227e00
.... r22 0xc00000002018fb60
.... r23 0x1
.... r24 0xc000003ffec4d900
.... r25 0x80000000
.... r26 0x0
.... r27 0x1
.... r28 0x1
.... r29 0xc000000001be1260
.... r30 0x6008010
.... r31 0xc000003ffebb7218
.... nip 0xc00000000012b910
.... msr 0x9000000000009033
.... orig_r3 0xc00000000012b86c
.... ctr 0xc0000000001299c0
.... link 0xc00000000012b77c
.... xer 0x0
.... ccr 0x28002222
.... softe 0x1
.... trap 0xf00
.... dar 0x0
.... dsisr 0x80000000000
.... sier 0x0
.... mmcra 0x80000000000
.... mmcr0 0x82008090
.... mmcr1 0x1e000000
.... mmcr2 0x0
... thread: perf:4784
Signed-off-by: Anju T Sudhakar <[email protected]>
Signed-off-by: Athira Rajeev <[email protected]>
Tested-by: Nageswara R Sastry <[email protected]>
Reviewed-by: Madhavan Srinivasan <[email protected]>
Reviewed-by: Kajol Jain <[email protected]>
Reviewed-and-tested-by: Ravi Bangoria <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
On POWER10 bit 12 in the PVR indicates if the core is SMT4 or SMT8.
Bit 12 is set for SMT4.
Without this patch, /proc/cpuinfo on a SMT4 DD1 POWER10 looks like
this:
cpu : POWER10, altivec supported
revision : 17.0 (pvr 0080 1100)
Fixes: a3ea40d5c736 ("powerpc: Add POWER10 architected mode")
Cc: [email protected] # v5.8
Signed-off-by: Michael Neuling <[email protected]>
Reviewed-by: Vaidyanathan Srinivasan <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Endianness issue in IPv4 option support in nft_exthdr,
from Stephen Suryaputra.
2) Removes the waitcount optimization in nft_compat,
from Florian Westphal.
3) Remove ipv6 -> nf_defrag_ipv6 module dependency, from
Florian Westphal.
4) Memleak in chain binding support, also from Florian.
5) Simplify nft_flowtable.sh selftest, from Fabian Frederick.
6) Optional MTU arguments for selftest nft_flowtable.sh,
also from Fabian.
7) Remove noise error report when killing process in
selftest nft_flowtable.sh, from Fabian Frederick.
8) Reject bogus getsockopt option length in ebtables,
from Florian Westphal.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2020-08-15
this is a pull request of 4 patches for net/master.
All patches are by Zhang Changzhong and fix broadcast related problems in the
j1939 CAN networking stack.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
We may access the two bytes after vlan_hdr in vlan_set_encap_proto(). So
we should pull VLAN_HLEN + sizeof(unsigned short) in skb_vlan_untag() or
we may access the wrong data.
Fixes: 0d5501c1c828 ("net: Always untag vlan-tagged traffic on input.")
Signed-off-by: Miaohe Lin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When an XDP program changes the ethernet header protocol field,
eth_type_trans is used to recalculate skb->protocol. In order for
eth_type_trans to work correctly, the ethernet header must actually be
part of the skb data segment, so the code first pushes that onto the
head of the skb. However, it subsequently forgets to pull it back off,
making the behavior of the passed-on packet inconsistent between the
protocol modifying case and the static protocol case. This patch fixes
the issue by simply pulling the ethernet header back off of the skb
head.
Fixes: 297249569932 ("net: fix generic XDP to handle if eth header was mangled")
Cc: Jesper Dangaard Brouer <[email protected]>
Cc: David S. Miller <[email protected]>
Signed-off-by: Jason A. Donenfeld <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Processing NETDEV_FEAT_CHANGE causes IPvlan links to lose
NETIF_F_LLTX feature because of the incorrect handling of
features in ipvlan_fix_features().
--before--
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~# ethtool -K ipvl0 tso off
Cannot change tcp-segmentation-offload
Actual changes:
vlan-challenged: off [fixed]
tx-lockless: off [fixed]
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: off [fixed]
lpaa10:~#
--after--
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~# ethtool -K ipvl0 tso off
Cannot change tcp-segmentation-offload
Could not change any device features
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~#
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Mahesh Bandewar <[email protected]>
Cc: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When we tear down a network namespace, we unregister all
the netdevices within it. So we may queue a slave device
and a bonding device together in the same unregister queue.
If the only slave device is non-ethernet, it would
automatically unregister the bonding device as well. Thus,
we may end up unregistering the bonding device twice.
Workaround this special case by checking reg_state.
Fixes: 9b5e383c11b0 ("net: Introduce unregister_netdevice_many()")
Reported-by: [email protected]
Cc: Eric Dumazet <[email protected]>
Cc: Andy Gospodarek <[email protected]>
Cc: Jay Vosburgh <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|