| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Cache block invalidation is removing an entry from the cache without
writing it back. Cache blocks can be invalidated via the
'invalidate_cblocks' message, which takes an arbitrary number of cblock
ranges:
invalidate_cblocks [<cblock>|<cblock begin>-<cblock end>]*
E.g.
dmsetup message my_cache 0 invalidate_cblocks 2345 3456-4567 5678-6789
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Implement policy_remove_cblock() and add remove_cblock method to the mq
policy. These methods will be used by the following cache block
invalidation patch which adds the 'invalidate_cblocks' message to the
cache core.
Also, update some comments in dm-cache-policy.h
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Rather than storing the cblock in each cache entry, we allocate all
entries in an array and infer the cblock from the entry position.
Saves 4 bytes of memory per cache block. In addition, this gives us an
easy way of looking up cache entries by cblock.
We no longer need to keep an explicit bitset to track which cblocks
have been allocated. And no searching is needed to find free cblocks.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Need to check the version to verify on-disk metadata is supported.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
"Passthrough" is a dm-cache operating mode (like writethrough or
writeback) which is intended to be used when the cache contents are not
known to be coherent with the origin device. It behaves as follows:
* All reads are served from the origin device (all reads miss the cache)
* All writes are forwarded to the origin device; additionally, write
hits cause cache block invalidates
This mode decouples cache coherency checks from cache device creation,
largely to avoid having to perform coherency checks while booting. Boot
scripts can create cache devices in passthrough mode and put them into
service (mount cached filesystems, for example) without having to worry
about coherency. Coherency that exists is maintained, although the
cache will gradually cool as writes take place.
Later, applications can perform coherency checks, the nature of which
will depend on the type of the underlying storage. If coherency can be
verified, the cache device can be transitioned to writethrough or
writeback mode while still warm; otherwise, the cache contents can be
discarded prior to transitioning to the desired operating mode.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Heinz Mauelshagen <[email protected]>
Signed-off-by: Morgan Mears <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Allow a cache to shrink if the blocks being removed from the cache are
not dirty.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
If a write block triggers promotion and covers a whole block we can
avoid a copy.
Introduce dm_{hook,unhook}_bio to simplify saving and restoring bio
fields (bi_private is now used by overwrite). Switch writethrough
support over to using these helpers too.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Previously these promotions only got priority if there were unused cache
blocks. Now we give them priority if there are any clean blocks in the
cache.
The fio_soak_test in the device-mapper-test-suite now gives uniform
performance across subvolumes (~16 seconds).
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
There are now two multiqueues for in cache blocks. A clean one and a
dirty one.
writeback_work comes from the dirty one. Demotions come from the clean
one.
There are two benefits:
- Performance improvement, since demoting a clean block is a noop.
- The cache cleans itself when io load is light.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Heinz Mauelshagen <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Check commit_requested flag _before_ calling
dm_cache_changed_this_transaction() superfluously.
Also, be sure to set last_commit_jiffies _after_ dm_cache_commit()
completes.
Signed-off-by: Heinz Mauelshagen <[email protected]>
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Don't waste time spotting blocks that have been allocated and then freed
in the same transaction.
The extra lookup is expensive, and I don't think it really gives us much.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Signed-off-by: Mike Snitzer <[email protected]>
|
|
The option DM_LOG_USERSPACE is sub-option of DM_MIRROR, so place it
right after DM_MIRROR. Doing so fixes various other Device mapper
targets/features to be properly nested under "Device mapper support".
Signed-off-by: Mikulas Patocka <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
This patch allows the removal of an open device to be deferred until
it is closed. (Previously such a removal attempt would fail.)
The deferred remove functionality is enabled by setting the flag
DM_DEFERRED_REMOVE in the ioctl structure on DM_DEV_REMOVE or
DM_REMOVE_ALL ioctl.
On return from DM_DEV_REMOVE, the flag DM_DEFERRED_REMOVE indicates if
the device was removed immediately or flagged to be removed on close -
if the flag is clear, the device was removed.
On return from DM_DEV_STATUS and other ioctls, the flag
DM_DEFERRED_REMOVE is set if the device is scheduled to be removed on
closure.
A device that is scheduled to be deleted can be revived using the
message "@cancel_deferred_remove". This message clears the
DMF_DEFERRED_REMOVE flag so that the device won't be deleted on close.
Signed-off-by: Mikulas Patocka <[email protected]>
Signed-off-by: Alasdair G Kergon <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
If preresume fails it is worth logging an error given that a device is
left suspended due to the failure.
This change was motivated by local preresume error logging that was
added to the cache target ("preresume failed"). Elevating this
target-agnostic context for the where the target-specific error occurred
relative to the DM core's callouts makes sense.
Signed-off-by: Mike Snitzer <[email protected]>
Signed-off-by: Joe Thornber <[email protected]>
|
|
dm-crypt can already activate TCRYPT (TrueCrypt compatible) containers
in LRW or XTS block encryption mode.
TCRYPT containers prior to version 4.1 use CBC mode with some additional
tweaks, this patch adds support for these containers.
This new mode is implemented using special IV generator named TCW
(TrueCrypt IV with whitening). TCW IV only supports containers that are
encrypted with one cipher (Tested with AES, Twofish, Serpent, CAST5 and
TripleDES).
While this mode is legacy and is known to be vulnerable to some
watermarking attacks (e.g. revealing of hidden disk existence) it can
still be useful to activate old containers without using 3rd party
software or for independent forensic analysis of such containers.
(Both the userspace and kernel code is an independent implementation
based on the format documentation and it completely avoids use of
original source code.)
The TCW IV generator uses two additional keys: Kw (whitening seed, size
is always 16 bytes - TCW_WHITENING_SIZE) and Kiv (IV seed, size is
always the IV size of the selected cipher). These keys are concatenated
at the end of the main encryption key provided in mapping table.
While whitening is completely independent from IV, it is implemented
inside IV generator for simplification.
The whitening value is always 16 bytes long and is calculated per sector
from provided Kw as initial seed, xored with sector number and mixed
with CRC32 algorithm. Resulting value is xored with ciphertext sector
content.
IV is calculated from the provided Kiv as initial IV seed and xored with
sector number.
Detailed calculation can be found in the Truecrypt documentation for
version < 4.1 and will also be described on dm-crypt site, see:
http://code.google.com/p/cryptsetup/wiki/DMCrypt
The experimental support for activation of these containers is already
present in git devel brach of cryptsetup.
Signed-off-by: Milan Broz <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Some encryption modes use extra keys (e.g. loopAES has IV seed) which
are not used in block cipher initialization but are part of key string
in table constructor.
This patch adds an additional field which describes the length of the
extra key(s) and substracts it before real key encryption setting.
The key_size always includes the size, in bytes, of the key provided
in mapping table.
The key_parts describes how many parts (usually keys) are contained in
the whole key buffer. And key_extra_size contains size in bytes of
additional keys part (this number of bytes must be subtracted because it
is processed by the IV generator).
| K1 | K2 | .... | K64 | Kiv |
|----------- key_size ----------------- |
| |-key_extra_size-|
| [64 keys] | [1 key] | => key_parts = 65
Example where key string contains main key K, whitening key
Kw and IV seed Kiv:
| K | Kiv | Kw |
|--------------- key_size --------------|
| |-----key_extra_size------|
| [1 key] | [1 key] | [1 key] | => key_parts = 3
Because key_extra_size is calculated during IV mode setting, key
initialization is moved after this step.
For now, this change has no effect to supported modes (thanks to ilog2
rounding) but it is required by the following patch.
Also, fix a sparse warning in crypt_iv_lmk_one().
Signed-off-by: Milan Broz <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
A migration failure should be logged (albeit limited).
Signed-off-by: Heinz Mauelshagen <[email protected]>
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Fix a few cell_defer() calls that weren't passing a bool.
Signed-off-by: Heinz Mauelshagen <[email protected]>
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Return -EINVAL when the specified cache policy is unknown rather than
returning -ENOMEM.
Signed-off-by: Mikulas Patocka <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Rename takeout_queue to concat_queue.
Fix a harmless bug in mq policies pop() function. Currently pop()
always succeeds, with up coming changes this wont be the case.
Fix typo in comment above pre_cache_to_cache prototype.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
No need to return from a void function.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Make the quiescing flag an atomic_t and stop protecting it with a spin
lock.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
for a shutdown
The code that was trying to do this was inadequate. The postsuspend
method (in ioctl context), needs to wait for the worker thread to
acknowledge the request to quiesce. Otherwise the migration count may
drop to zero temporarily before the worker thread realises we're
quiescing. In this case the target will be taken down, but the worker
thread may have issued a new migration, which will cause an oops when
it completes.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
Cc: [email protected] # 3.9+
|
|
Previously only origin bios could trigger ticks, which meant if all
the io was destined for the cache no ticks were generated. If no ticks
are generated then multiple hits, and movements in general, are
attributed to the same tick.
Only a stop gap fix, we need a better solution.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
It is safe to use a mutex in mq_residency() at this point since it is
only called from ioctl context. But future-proof mq_residency() by
using might_sleep() to catch new contexts that cannot sleep.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Entries would be lost if the old tail block was partially filled.
Signed-off-by: Joe Thornber <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
Cc: [email protected] # 3.9+
|
|
When pg_init is running no I/O can be submitted to the underlying
devices, as the path priority etc might change. When using queue_io for
this, requests will be piling up within multipath as the block I/O
scheduler just sees a _very fast_ device. All of this queued I/O has to
be resubmitted from within multipathing once pg_init is done.
This approach has the problem that it's virtually impossible to
abort I/O when pg_init is running, and we're adding heavy load
to the devices after pg_init since all of the queued I/O needs to be
resubmitted _before_ any requests can be pulled off of the request queue
and normal operation continues.
This patch will requeue the I/O that triggers the pg_init call, and
return 'busy' when pg_init is in progress. With these changes the block
I/O scheduler will stop submitting I/O during pg_init, resulting in a
quicker path switch and less I/O pressure (and memory consumption) after
pg_init.
Signed-off-by: Hannes Reinecke <[email protected]>
[patch header edited for clarity and typos by Mike Snitzer]
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Whenever multipath_dtr() is happening we must prevent queueing any
further path activation work. Implement this by adding a new
'pg_init_disabled' flag to the multipath structure that denotes future
path activation work should be skipped if it is set. By disabling
pg_init and then re-enabling in flush_multipath_work() we also avoid the
potential for pg_init to be initiated while suspending an mpath device.
Without this patch a race condition exists that may result in a kernel
panic:
1) If after pg_init_done() decrements pg_init_in_progress to 0, a call
to wait_for_pg_init_completion() assumes there are no more pending path
management commands.
2) If pg_init_required is set by pg_init_done(), due to retryable
mode_select errors, then process_queued_ios() will again queue the
path activation work.
3) If free_multipath() completes before activate_path() work is called a
NULL pointer dereference like the following can be seen when
accessing members of the recently destructed multipath:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000090
RIP: 0010:[<ffffffffa003db1b>] [<ffffffffa003db1b>] activate_path+0x1b/0x30 [dm_multipath]
[<ffffffff81090ac0>] worker_thread+0x170/0x2a0
[<ffffffff81096c80>] ? autoremove_wake_function+0x0/0x40
[switch to disabling pg_init in flush_multipath_work & header edits by Mike Snitzer]
Signed-off-by: Shiva Krishna Merla <[email protected]>
Reviewed-by: Krishnasamy Somasundaram <[email protected]>
Tested-by: Speagle Andy <[email protected]>
Acked-by: Junichi Nomura <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
Cc: [email protected]
|
|
dm-mpath and dm-thin must process messages even if some device is
suspended, so we allocate argv buffer with GFP_NOIO. These messages have
a small fixed number of arguments.
On the other hand, dm-switch needs to process bulk data using messages
so excessive use of GFP_NOIO could cause trouble.
The patch also lowers the default number of arguments from 64 to 8, so
that there is smaller load on GFP_NOIO allocations.
Signed-off-by: Mikulas Patocka <[email protected]>
Cc: [email protected]
Acked-by: Alasdair G Kergon <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
|
|
Pull watchdog fixes from Wim Van Sebroeck:
"This will fix a deadlock on the ts72xx_wdt driver, fix bitmasks in the
kempld_wdt driver and fix a section mismatch in the sunxi_wdt driver"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: sunxi: Fix section mismatch
watchdog: kempld_wdt: Fix bit mask definition
watchdog: ts72xx_wdt: locking bug in ioctl
|
|
This driver has a section mismatch, for probe and remove functions,
leading to the following warning during the compilation.
WARNING: drivers/watchdog/built-in.o(.data+0x24): Section mismatch in
reference from the variable sunxi_wdt_driver to the function
.init.text:sunxi_wdt_probe()
The variable sunxi_wdt_driver references
the function __init sunxi_wdt_probe()
Signed-off-by: Maxime Ripard <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Signed-off-by: Wim Van Sebroeck <[email protected]>
|
|
STAGE_CFG bits are defined as [5:4] bits. However, '(((x) & 0x30) << 4)'
handles [9:8] bits. Thus, it should be fixed in order to handle
[5:4] bits.
Signed-off-by: Jingoo Han <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Signed-off-by: Wim Van Sebroeck <[email protected]>
|
|
Calling the WDIOC_GETSTATUS & WDIOC_GETBOOTSTATUS and twice will cause a
interruptible deadlock.
Signed-off-by: Dan Carpenter <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Signed-off-by: Wim Van Sebroeck <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A small batch of fixes this week, mostly OMAP related. Nothing stands
out as particularly controversial.
Also a fix for a 3.12-rc1 timer regression for Exynos platforms,
including the Chromebooks"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: exynos: dts: Update 5250 arch timer node with clock frequency
ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
ARM: mach-omap2: board-generic: fix undefined symbol
ARM: dts: Fix pinctrl mask for omap3
ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
|
|
Without the "clock-frequency" property in arch timer node, could able
to see the below crash dump.
[<c0014e28>] (unwind_backtrace+0x0/0xf4) from [<c0011808>] (show_stack+0x10/0x14)
[<c0011808>] (show_stack+0x10/0x14) from [<c036ac1c>] (dump_stack+0x7c/0xb0)
[<c036ac1c>] (dump_stack+0x7c/0xb0) from [<c01ab760>] (Ldiv0_64+0x8/0x18)
[<c01ab760>] (Ldiv0_64+0x8/0x18) from [<c0062f60>] (clockevents_config.part.2+0x1c/0x74)
[<c0062f60>] (clockevents_config.part.2+0x1c/0x74) from [<c0062fd8>] (clockevents_config_and_register+0x20/0x2c)
[<c0062fd8>] (clockevents_config_and_register+0x20/0x2c) from [<c02b8e8c>] (arch_timer_setup+0xa8/0x134)
[<c02b8e8c>] (arch_timer_setup+0xa8/0x134) from [<c04b47b4>] (arch_timer_init+0x1f4/0x24c)
[<c04b47b4>] (arch_timer_init+0x1f4/0x24c) from [<c04b40d8>] (clocksource_of_init+0x34/0x58)
[<c04b40d8>] (clocksource_of_init+0x34/0x58) from [<c049ed8c>] (time_init+0x20/0x2c)
[<c049ed8c>] (time_init+0x20/0x2c) from [<c049b95c>] (start_kernel+0x1e0/0x39c)
THis is because the Exynos u-boot, for example on the Chromebooks, doesn't set
up the CNTFRQ register as expected by arch_timer. Instead, we have to specify
the frequency in the device tree like this.
Signed-off-by: Yuvaraj Kumar C D <[email protected]>
[olof: Changed subject, added comment, elaborated on commit message]
Signed-off-by: Olof Johansson <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few fixes for omap3 related hangs and errors that people have
noticed now that people are actually using the device tree
based booting for omap3.
Also one regression fix for timer compile for dra7xx when
omap5 is not selected, and a LED regression fix for n900.
* tag 'fixes-against-v3.12-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
ARM: mach-omap2: board-generic: fix undefined symbol
ARM: dts: Fix pinctrl mask for omap3
ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
Signed-off-by: Olof Johansson <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"This patchset includes a bugfix to prevent a kernel crash when memory
in page zero is accessed by the kernel itself, e.g. via
probe_kernel_read().
Furthermore we now export flush_cache_page() which is needed
(indirectly) by the lustre filesystem. The other patches remove
unused functions and optimizes the page fault handler to only evaluate
variables if needed, which again protects against possible kernel
crashes"
* 'parisc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: let probe_kernel_read() capture access to page zero
parisc: optimize variable initialization in do_page_fault
parisc: fix interruption handler to respect pagefault_disable()
parisc: mark parisc_terminate() noreturn and cold.
parisc: remove unused syscall_ipi() function.
parisc: kill SMP single function call interrupt
parisc: Export flush_cache_page() (needed by lustre)
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"Another week, time to send another fixes request taking time out of
extended weekend for the festivities in this part of the world.
We have two fixes from Sergei for rcar driver and one fixing memory
leak of edma driver by Geyslan"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: edma.c: remove edma_desc leakage
rcar-hpbdma: add parameter to set_slave() method
rcar-hpbdma: remove shdma_free_irq() calls
|
|
Signed-off-by: Helge Deller <[email protected]>
|
|
The attached change defers the initialization of the variables tsk, mm
and flags until they are needed. As a result, the code won't crash if a
kernel probe is done with a corrupt context and the code will be better
optimized.
Signed-off-by: John David Anglin <[email protected]>
Signed-off-by: Helge Deller <[email protected]>
|
|
Running an "echo t > /proc/sysrq-trigger" crashes the parisc kernel. The
problem is, that in print_worker_info() we try to read the workqueue info via
the probe_kernel_read() functions which use pagefault_disable() to avoid
crashes like this:
probe_kernel_read(&pwq, &worker->current_pwq, sizeof(pwq));
probe_kernel_read(&wq, &pwq->wq, sizeof(wq));
probe_kernel_read(name, wq->name, sizeof(name) - 1);
The problem here is, that the first probe_kernel_read(&pwq) might return zero
in pwq and as such the following probe_kernel_reads() try to access contents of
the page zero which is read protected and generate a kernel segfault.
With this patch we fix the interruption handler to call parisc_terminate()
directly only if pagefault_disable() was not called (in which case
preempt_count()==0). Otherwise we hand over to the pagefault handler which
will try to look up the faulting address in the fixup tables.
Signed-off-by: Helge Deller <[email protected]>
Cc: <[email protected]> # v3.0+
Signed-off-by: John David Anglin <[email protected]>
Signed-off-by: Helge Deller <[email protected]>
|
|
Signed-off-by: Helge Deller <[email protected]>
|
|
Signed-off-by: Helge Deller <[email protected]>
|
|
Commit 9a46ad6d6df3b54 "smp: make smp_call_function_many() use logic
similar to smp_call_function_single()" has unified the way to handle
single and multiple cross-CPU function calls. Now only one interrupt
is needed for architecture specific code to support generic SMP function
call interfaces, so kill the redundant single function call interrupt.
Signed-off-by: Jiang Liu <[email protected]>
Cc: Jiang Liu <[email protected]>
Signed-off-by: Helge Deller <[email protected]>
|
|
ERROR: "flush_cache_page" [drivers/staging/lustre/lustre/libcfs/libcfs.ko] undefined!
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Helge Deller <[email protected]>
|
|
Olga reported that file descriptors opened with O_PATH do not work with
fstatfs(), found during further development of ksh93's thread support.
There is no reason to not allow O_PATH file descriptors here (fstatfs is
very much a path operation), so use "fdget_raw()". See commit
55815f70147d ("vfs: make O_PATH file descriptors usable for 'fstat()'")
for a very similar issue reported for fstat() by the same team.
Reported-and-tested-by: ольга крыжановская <[email protected]>
Acked-by: Al Viro <[email protected]>
Cc: [email protected] # O_PATH introduced in 3.0+
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"A bug fix and performance regression fix for ext4"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix memory leak in xattr
ext4: fix performance regression in writeback of random writes
|