Age | Commit message (Collapse) | Author | Files | Lines |
|
The FSR (Firmware State Register) can be found at offset 0 in the SRAM and
it is holding information about the state of the ROM/FW.
In case of a boot failure it can be used to get the state where the boot
process got stuck, it does not itself contains error codes as such.
The error code (or the firmware state information) is stored in the next
soft register at offset 0x4.
Signed-off-by: Peter Ujfalusi <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Rander Wang <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
'ret' is never used. Remove it and return 0 instead.
Signed-off-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Bard Liao <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Peter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
When an FE, typically non-atomic, is connected to an atomic BE, we
force the BE as non-atomic. There's no reason to throw a warning, this
is a perfectly fine configuration and a conversion that's required
by-design.
This removes the unconditional warnings such as
[ 12.054213] iDisp1: dpcm_be_connect: FE is nonatomic but BE is not, forcing BE as nonatomic
[ 12.074693] iDisp2: dpcm_be_connect: FE is nonatomic but BE is not, forcing BE as nonatomic
[ 12.096612] iDisp3: dpcm_be_connect: FE is nonatomic but BE is not, forcing BE as nonatomic
[ 12.118637] iDisp4: dpcm_be_connect: FE is nonatomic but BE is not, forcing BE as nonatomic
[ 12.140660] dmic01: dpcm_be_connect: FE is nonatomic but BE is not, forcing BE as nonatomic
[ 12.147521] dmic16k: dpcm_be_connect: FE is nonatomic but BE is not, forcing BE as nonatomic
and demotes them to dev_dbg(), as suggested in review comments.
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Péter Ujfalusi <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Use a dedicated flag instead of directly checking the
sdev->system_suspend_target to decide if we need to skip IMR boot due to
too deep sleep state where the memory used for IMR booting will not retain
its content.
The skip_imr_boot flag will be set true during suspend if the target state
is deeper than S3 and reset back to false on successful boot to re-enable
IMR booting in shallower sleep states.
Signed-off-by: Peter Ujfalusi <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
It is not yet clear, but it is possible to create a firmware so broken
that it will send a reply message before a FW_READY message (it is not
yet clear if FW_READY will arrive later).
Since the reply_data is allocated only after the FW_READY message, this
will lead to a NULL pointer dereference if not filtered out.
Reported-by: Kai Vehmanen <[email protected]>
Signed-off-by: Peter Ujfalusi <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
It is not yet clear, but it is possible to create a firmware so broken
that it will send a reply message before a FW_READY message (it is not
yet clear if FW_READY will arrive later).
Since the reply_data is allocated only after the FW_READY message, this
will lead to a NULL pointer dereference if not filtered out.
The issue was reported with IPC4 firmware but the same condition is present
for IPC3.
Reported-by: Kai Vehmanen <[email protected]>
Signed-off-by: Peter Ujfalusi <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
It is not yet clear, but it is possible to create a firmware so broken
that it will send a reply message before a FW_READY message (it is not
yet clear if FW_READY will arrive later).
Since the reply_data is allocated only after the FW_READY message, this
will lead to a NULL pointer dereference if not filtered out.
The issue was reported with IPC4 firmware but the same condition is present
for IPC3.
Reported-by: Kai Vehmanen <[email protected]>
Signed-off-by: Peter Ujfalusi <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
On a HP 288 Pro G6, the front mic could not be detected.In order to
get it working, the pin configuration needs to be set correctly, and
the ALC671_FIXUP_HP_HEADSET_MIC2 fixup needs to be applied.
Signed-off-by: Meng Tang <[email protected]>
Cc: <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Drop duplicate print of returned value in the messages and use pattern
return dev_err_probe(...) where it's possible.
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The comments are inconsistent and point to the wrong driver name.
The initially named i2c-multi-instantiate it was renamed to the
serial-multi-instantiate exactly due to support of the platforms
with multiple CS35L41 codecs.
Fix comments accordingly.
While at it, drop file names from the files.
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Another Dell model, another fixup entry: Latitude E5430 needs the same
fixup as other Latitude E series as workaround for noise problems.
Signed-off-by: Meng Tang <[email protected]>
Cc: <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Merge series from Cezary Rojewski <[email protected]>:
Series consists of loosely connected patches and does not concentrate on
one specific subject.
First, as generic HDAudio codec driver is now part of ASoC, avs-driver
core is updated to register missing ext_bus operations. This completes
driver's core implementation.
The next change adds the last missing piece for port descriptions coming
from topology in formatted string format e.g.: ssp%d have full
effect. To do that, the port value needs to be provided to respective
copier configuration.
Third change relaxes core transition timings so that scenarios where
modules are interfering with each other while being on separate cores
are not occasionally causing trouble.
All other changes are addressing warnings, cleaning things up a little
and protecting driver from invalid firmware behavior - while not
expected in release binaries, does not hurt to add them.
|
|
This patch adds the function of headphone button detection,
Button detection will be enabled if the device tree
has a key_enable property.
Signed-off-by: Seven Lee <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Merge series from Amadeusz Sławiński <[email protected]>:
Our tests platforms do use realtek codecs, while implementing avs driver
and machine boards for it, we identified some problems with those codec
drivers.
This series aims to fix those issues.
|
|
Merge series from V sujith kumar Reddy <[email protected]>:
Add Generic driver to support multiple platform,
ADD HS control instance for Rembrandt platform.
Add nau8825,max98560 and rt5682s,rt1019 combination support for legacy
platform.
|
|
Merge series from Pierre-Louis Bossart <[email protected]>:
Two patches to improve error and memory handling. When IPC4 is used,
some of the flows were incorrect.
|
|
We should only have an error when enforcing strict mapping between
kernel and firmware versions. In all other cases, there is no reason
to throw a warning.
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Péter Ujfalusi <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Remove extra space in front of mchp_pdmc_dt_init().
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Needed for the Rockchip driver.
|
|
There is another HP ProDesk 600 G3 model with the PCI SSID 103c:82b4
that requires the quirk HP_MIC_NO_PRESENCE. Add the corresponding
entry to the quirk table.
Signed-off-by: Meng Tang <[email protected]>
Cc: <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The issue on Acer SWIFT SF313-51 is that headset microphone
doesn't work. The following quirk fixed headset microphone issue.
Note that the fixup of SF314-54/55 (ALC256_FIXUP_ACER_HEADSET_MIC)
was not successful on my SF313-51.
Signed-off-by: Meng Tang <[email protected]>
Cc: <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Make sure that component is set to proper value, otherwise we may
dereference freed component in interrupt.
Signed-off-by: Amadeusz Sławiński <[email protected]>
Reviewed-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Make sure that component is set to proper value, otherwise we may
dereference freed component in interrupt.
Signed-off-by: Amadeusz Sławiński <[email protected]>
Reviewed-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Make sure that component is set to proper value, otherwise we may
dereference freed component in interrupt.
Signed-off-by: Amadeusz Sławiński <[email protected]>
Reviewed-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
On our RVP platforms using rt298 with combojack we've seen issues with
controls being in incorrect state after suspend/resume cycle. This is
caused by codec driver not setting pins to correct state and causing
codec suspend method to not be called. Which on resume caused codec
registers to be in undefined state. Fix this by setting pins correctly
in jack detect function.
Above problem is caused by the fact that when jack == NULL code doesn't
reach rt298_jack_detect() function which sets pins. Alternatively
problem could be fixed by just moving rt298_jack_detect, but as rt298
codec is similar to rt286, align the code by setting pins explicitly.
Signed-off-by: Amadeusz Sławiński <[email protected]>
Reviewed-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Set rt298->jack to passed value in mic_detect, otherwise when jack is
set to NULL on next interrupt call, we may use freed pointer.
Signed-off-by: Amadeusz Sławiński <[email protected]>
Reviewed-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Commit a5450aba737d ("ASoC: rockchip: i2s: switch BCLK to GPIO") switched
BCLK to GPIO functions when probing the i2s bus interface, but missed
adding a check for when devm_pinctrl_get() returns an error. This can lead
to the following NULL pointer dereference on a rockpro64-v2 if there are no
"pinctrl" properties in the i2s device tree node.
Check that i2s->pinctrl is valid before attempting to search for the
bclk_on and bclk_off pinctrl states.
Fixes: a5450aba737d ("ASoC: rockchip: i2s: switch BCLK to GPIO")
Signed-off-by: Alexandru Elisei <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Avoid build errors when CONFIG_COMMON_CLK is not set/enabled.
ERROR: modpost: "__clk_get_name" [sound/soc/fsl/snd-soc-fsl-utils.ko] undefined!
Fixes: 7bad8125549c ("ASoC: fsl_utils: Add function to handle PLL clock source")
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Shengjiu Wang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Remove condition with no effect
Signed-off-by: Zhongjun Tan <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Fix StatVectorSel wrong setting.
Fixes: b7f6503830 ("ASoC: SOF: mediatek: Add fw loader and mt8195 dsp ops to load firmware")
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: YC Hung <[email protected]>
Reviewed-by: Li-Yu Yu <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: KuanHsun Cheng <[email protected]>
Reviewed-by: Péter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
1. Revise hifixdsp shutdown flow to pull runstall high then reset high.
2. Add 1 us delay between D/BRESET high and low for 10 DSP cycles(26M)
based on IP vendor's suggestion.
Signed-off-by: YC Hung <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Li-Yu Yu <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: KuanHsun Cheng <[email protected]>
Reviewed-by: Péter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
It is not used anywhere in the file, so there is no need to keep it.
Signed-off-by: Amadeusz Sławiński <[email protected]>
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Old code resets SIE for up to 8 streams using byte accessor, but
register is laid out in following way:
31 GIE
30 CIE
29:x Reserved
x-1:0 SIE
If there is more than 8 streams, some of them may and up with enabled
interrupts. To fix this just clear whole INTCTL register when disabling
interrupts.
Signed-off-by: Amadeusz Sławiński <[email protected]>
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
If early probe of HDAudio bus driver fails e.g.: due to missing
firmware file, snd_hda_codec_shutdown() ends in manipulating
uninitialized codec->pcm_list_head causing page fault.
Iinitialization of HDAudio codec in ASoC is split in two:
- snd_hda_codec_device_init()
- snd_hda_codec_device_new()
snd_hda_codec_device_init() is called during probe_codecs() by HDAudio
bus driver while snd_hda_codec_device_new() is called by
codec-component's ->probe(). The second call will not happen until all
components required by related sound card are present within the ASoC
framework. With firmware failing to load during the PCI's deferred
initialization i.e.: probe_work(), no platform components are ever
registered. HDAudio codec enumeration is done at that point though, so
the codec components became registered to ASoC framework, calling
snd_hda_codec_device_init() in the process.
Now, during platform reboot snd_hda_codec_shutdown() is called for every
codec found on the HDAudio bus causing oops if any of them has not
completed both of their initialization steps. Relocating field
initialization fixes the issue.
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
AVS HDAudio bus driver does not tie with codec drivers tighly. Codec
device and its respective driver cleanup procedures are split and may
not occur one after the other. Device cleanup is performed only on
snd_hdac_ext_bus_device_remove() i.e. it's the bus driver's
responsibility. If codec component probing fails, put_device() found in
snd_hda_codec_device_new() may lead to page fault. Relocate it to
snd_hda_codec_new() to address the problem on ASoC side while keeping
status quo for snd_hda_intel.
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
AVS HDAudio bus driver does not tie with codec drivers tighly and
snd_hda_codec_device_new() can be called after codec's module reload. In
such case, rpm is forbidden and invoking pm_runtime_forbid()
unconditionally causes device's usage_count to become unbalanced. This
is later caught by WARN_ON() found in sound/soc/hda.c. Detect such
circumstance and bump the usage_count instead.
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
If snd_hda_hdmi_codec module is denylisted and any event causes i915
enumeration to fail, is_likely_hdmi_codec() ends in null-ptr-deref.
As snd_soc_hda is an ASoC-based driver, its initialization is delayed
until all the necessary components appear in the system - allowing
actual sound card to enumerate. snd_hda_codec_configure() gets called by
the avs-driver core during probe_codecs() but the
snd_hda_codec_device_new(), necessary to complete codecs initialization,
happens only when codec-component of hda sound card is being probed.
Denylisting snd_hda_codec_hdmi module causes snd_hda_codec_configure()
to reach: codec_bind_generic() -> is_likely_hdmi_codec() which makes use
of ->wcaps and at this point the it isn't initialized yet - again,
requires completion of snd_hda_codec_device_new().
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.19
Quite a large batch due to things building up for a couple of weeks but
all driver specific apart from Marek's documentation fix.
|
|
Merge series from Kuninori Morimoto <[email protected]>:
Audio Graph Card2 has Codec2Codec support, but I noticed
- Current Codec2Codec setting value is not correct
because it is using of_get_property().
- simple-card-utils has default Codec2Codec settings
and it is overwriting Card2 settings
- This default settings works for non Codec2Codec case
(= DPCM::BE case) too.
This patch-set solve these issues.
|
|
Merge series from Brent Lu <[email protected]>:
1. Add BT offload fetch to cs42l42 machine driver
2. Support cs42l42+max98360a on ADL platform
|
|
Free the memories allocated in sof_ipc4_get_audio_fmt in error handling
and ipc_free()
Fixes: 2cabd02b6090 ("ASoC: SOF: ipc4-topology: Add support for parsing AIF_IN/AIF_OUT widgets")
Fixes: abfb536bd116 ("ASoC: SOF: ipc4-topology: Add support for parsing DAI_IN/DAI_OUT widgets")
Fixes: 4f838ab20812 ("ASoC: SOF: ipc4-topology: Add support for parsing and preparing pga widgets")
Fixes: 4d4ba014ac4b ("ASoC: SOF: ipc4-topology: Add support for parsing mixer widgets")
Reviewed-by: Péter Ujfalusi <[email protected]>
Signed-off-by: Libin Yang <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Set the swidget->private or dai->private to NULL after kfree in the error
handling in ipc_setup(). The private needs to be set NULL because if
ipc_setup() returns error, ipc_free() will be called later. ipc_free()
will judge the private is NULL or not to do the clearing.
For dai widget, dai->private is allocated and set in dai widget
ipc_setup(). So we need to check dai->private is NULL or not
in the ipc_free().
Fixes: 2cabd02b6090 ("ASoC: SOF: ipc4-topology: Add support for parsing AIF_IN/AIF_OUT widgets")
Fixes: abfb536bd116 ("ASoC: SOF: ipc4-topology: Add support for parsing DAI_IN/DAI_OUT widgets")
Fixes: 4f838ab20812 ("ASoC: SOF: ipc4-topology: Add support for parsing and preparing pga widgets")
Fixes: 4d4ba014ac4b ("ASoC: SOF: ipc4-topology: Add support for parsing mixer widgets")
Reviewed-by: Péter Ujfalusi <[email protected]>
Signed-off-by: Libin Yang <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
To reduce the number of places to update if timeouts would have to
change, modify the constant declaration.
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Module unloading operation performs memory unmapping and the weight of
the opration does not different from any other standard IPC. There is no
dependency on secondary task like in module loading scenario where
larger message timeout is recommended.
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Improve readability of CLDMA reset operation by making use of
already defined SD_CTL_STREAM_RESET.
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
If exposed by firmware, count RESERVED parameter as known one to avoid
dumping noise in kernel logs.
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
dma_set_mask() and dma_set_coherent_mask() can be performed with one
call to dma_set_mask_and_coherent(), which slightly reduces amount of
code on our side.
Signed-off-by: Amadeusz Sławiński <[email protected]>
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Apparently it is possible for code to allocate large buffers which may
cause warnings as reported in [1]. This was fixed for HDA, SOF and
skylake in patchset [2], fix it also for avs driver.
[1] https://github.com/thesofproject/linux/issues/3430
[2] https://lore.kernel.org/all/[email protected]/
Signed-off-by: Amadeusz Sławiński <[email protected]>
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
To allow for driver's filesystem interfaces e.g.: debugfs, to be touched
even when the device is asleep, mark IPC-channel as blocked when the
device is suspended. This causes any invocation of said interfaces that
do not toggle PM themselves to gracefully fail with "Operation not
permitted" message.
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Some LARGE_CONFIG_GETs are never expected to return payload of size 0.
Check for such situation and collapse if met.
Signed-off-by: Cezary Rojewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|