aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2017-03-21drm/exynos/decon5433: fix software trigger maskAndrzej Hajda1-2/+2
The patch fixes copy/paste bug introduced during code refactoring. Reported-by: Dan Carpenter <[email protected]> Fixes: b93c2e8b5d9d ("drm/exynos/decon5433: configure sysreg in case of hardware trigger")Fixes: Signed-off-by: Andrzej Hajda <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2017-03-21drm/exynos/fimd: signal frame done interrupt at front porchAndrzej Hajda1-1/+1
VBLANK interrupt should be signalled as soon as scanout ends, front porch is the best moment. Signed-off-by: Andrzej Hajda <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2017-03-21drm/exynos/decon5433: signal frame done interrupt at front porchAndrzej Hajda2-1/+5
DECON in case of video mode generates interrupt by default at start of vertical back porch. As this interrupt is used to generate VBLANK events more optimal point is start of vertical front porch. Signed-off-by: Inki Dae <[email protected]>
2017-03-21drm/exynos/decon5433: fix vblank event handlingAndrzej Hajda2-1/+85
Current implementation of event handling assumes that vblank interrupt is always called at the right time. It is not true, it can be delayed due to various reasons. As a result different races can happen. The patch fixes the issue by using hardware frame counter present in DECON to serialize vblank and commit completion events. Signed-off-by: Andrzej Hajda <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2017-03-21drm/exynos: move crtc event handling to drivers callbacksAndrzej Hajda7-13/+24
CRTC event is currently send with next vblank, or instantly in case crtc is being disabled. This approach usually works, but in corner cases it can result in premature event generation. Only device driver is able to verify if the event can be sent. This patch is a first step in that direction - it moves event handling to the drivers. Signed-off-by: Andrzej Hajda <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2017-03-21drm/exynos: Remove support for Exynos4415 (SoC not supported anymore)Krzysztof Kozlowski4-32/+3
Support for Exynos4415 is going away because there are no internal nor external users. Since commit 46dcf0ff0de3 ("ARM: dts: exynos: Remove exynos4415.dtsi"), the platform cannot be instantiated so remove also the drivers. Signed-off-by: Krzysztof Kozlowski <[email protected]> Acked-by: Kukjin Kim <[email protected]> Acked-by: Rob Herring <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2017-03-21drm/exynos/decon5433: & vs | typoDan Carpenter1-1/+1
"&" was obviously intended instead of "|". The original condition is always true. Fixes: b93c2e8b5d9d ("drm/exynos/decon5433: configure sysreg in case of hardware trigger") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2017-03-21cpufreq: schedutil: Fix per-CPU structure initialization in sugov_start()Rafael J. Wysocki1-13/+7
sugov_start() only initializes struct sugov_cpu per-CPU structures for shared policies, but it should do that for single-CPU policies too. That in particular makes the IO-wait boost mechanism work in the cases when cpufreq policies correspond to individual CPUs. Fixes: 21ca6d2c52f8 (cpufreq: schedutil: Add iowait boosting) Signed-off-by: Rafael J. Wysocki <[email protected]> Acked-by: Viresh Kumar <[email protected]> Cc: 4.9+ <[email protected]> # 4.9+
2017-03-20remoteproc: qcom: fix QCOM_SMD dependenciesArnd Bergmann1-3/+3
qcom_smd_register_edge() is provided by either QCOM_SMD or RPMSG_QCOM_SMD, and if both of them are disabled, it does nothing. The check for the PIL drivers however only checks for QCOM_SMD, so it breaks with QCOM_SMD=n && RPMSG_QCOM_SMD=m: drivers/remoteproc/built-in.o: In function `smd_subdev_remove': qcom_wcnss_iris.c:(.text+0x231c): undefined reference to `qcom_smd_unregister_edge' drivers/remoteproc/built-in.o: In function `smd_subdev_probe': qcom_wcnss_iris.c:(.text+0x2344): undefined reference to `qcom_smd_register_edge' drivers/remoteproc/built-in.o: In function `smd_subdev_probe': qcom_q6v5_pil.c:(.text+0x3538): undefined reference to `qcom_smd_register_edge' qcom_q6v5_pil.c:(.text+0x3538): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `qcom_smd_register_edge' This clarifies the Kconfig dependency. Fixes: 4b48921a8f74 ("remoteproc: qcom: Use common SMD edge handler") Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]>
2017-03-20ath10k: fix incorrect wlan_mac_base in qca6174_regsRyan Hsu1-1/+1
In the 'commit ebee76f7fa46 ("ath10k: allow setting coverage class")', it inherits the design and the address offset from ath9k, but the address is not applicable to QCA6174, which leads to a random crash while doing the resume() operation, since the set_coverage_class.ops will be called from ieee80211_reconfig() when resume() (if the wow is not configured). Fix the incorrect address offset here to avoid the random crash. Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2. kvalo: this also seems to fix a regression with firmware restart. Fixes: ebee76f7fa46 ("ath10k: allow setting coverage class") Cc: <[email protected]> # v4.10 Signed-off-by: Ryan Hsu <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2017-03-20f2fs: combine nat_bits and free_nid_bitmap cacheChao Yu1-78/+47
Both nat_bits cache and free_nid_bitmap cache provide same functionality as a intermediate cache between free nid cache and disk, but with different granularity of indicating free nid range, and different persistence policy. nat_bits cache provides better persistence ability, and free_nid_bitmap provides better granularity. In this patch we combine advantage of both caches, so finally policy of the intermediate cache would be: - init: load free nid status from nat_bits into free_nid_bitmap - lookup: scan free_nid_bitmap before load NAT blocks - update: update free_nid_bitmap in real-time - persistence: udpate and persist nat_bits in checkpoint This patch also resolves performance regression reported by lkp-robot. commit: 4ac912427c4214d8031d9ad6fbc3bc75e71512df ("f2fs: introduce free nid bitmap") d00030cf9cd0bb96fdccc41e33d3c91dcbb672ba ("f2fs: use __set{__clear}_bit_le") 1382c0f3f9d3f936c8bc42ed1591cf7a593ef9f7 ("f2fs: combine nat_bits and free_nid_bitmap cache") 4ac912427c4214d8 d00030cf9cd0bb96fdccc41e33 1382c0f3f9d3f936c8bc42ed15 ---------------- -------------------------- -------------------------- %stddev %change %stddev %change %stddev \ | \ | \ 77863 ± 0% +2.1% 79485 ± 1% +50.8% 117404 ± 0% aim7.jobs-per-min 231.63 ± 0% -2.0% 227.01 ± 1% -33.6% 153.80 ± 0% aim7.time.elapsed_time 231.63 ± 0% -2.0% 227.01 ± 1% -33.6% 153.80 ± 0% aim7.time.elapsed_time.max 896604 ± 0% -0.8% 889221 ± 3% -20.2% 715260 ± 1% aim7.time.involuntary_context_switches 2394 ± 1% +4.6% 2503 ± 1% +3.7% 2481 ± 2% aim7.time.maximum_resident_set_size 6240 ± 0% -1.5% 6145 ± 1% -14.1% 5360 ± 1% aim7.time.system_time 1111357 ± 3% +1.9% 1132509 ± 2% -6.2% 1041932 ± 2% aim7.time.voluntary_context_switches ... Signed-off-by: Chao Yu <[email protected]> Tested-by: Xiaolong Ye <[email protected]> Signed-off-by: Jaegeuk Kim <[email protected]>
2017-03-20f2fs: skip scanning free nid bitmap of full NAT blocksChao Yu3-6/+30
This patch adds to account free nids for each NAT blocks, and while scanning all free nid bitmap, do check count and skip lookuping in full NAT block. Signed-off-by: Chao Yu <[email protected]> Signed-off-by: Jaegeuk Kim <[email protected]>
2017-03-20f2fs: use __set{__clear}_bit_leJaegeuk Kim2-10/+10
This patch uses __set{__clear}_bit_le for highter speed. Reviewed-by: Chao Yu <[email protected]> Signed-off-by: Jaegeuk Kim <[email protected]>
2017-03-20f2fs: declare static functionsJaegeuk Kim1-3/+4
This is to avoid build warning reported by kbuild test robot. Signed-off-by: Fengguang Wu <[email protected]> Signed-off-by: Jaegeuk Kim <[email protected]>
2017-03-20f2fs: don't overwrite node block by SSRJaegeuk Kim1-0/+6
This patch fixes that SSR can overwrite previous warm node block consisting of a node chain since the last checkpoint. Fixes: 5b6c6be2d878 ("f2fs: use SSR for warm node as well") Reviewed-by: Chao Yu <[email protected]> Signed-off-by: Jaegeuk Kim <[email protected]>
2017-03-20generic syscalls: Wire up statx syscallStafford Horne1-1/+3
The new syscall statx is implemented as generic code, so enable it for architectures like openrisc which use the generic syscall table. Fixes: a528d35e8bfcc ("statx: Add a system call to make enhanced file info available") Cc: Thomas Gleixner <[email protected]> Cc: Al Viro <[email protected]> Cc: David Howells <[email protected]> Cc: Catalin Marinas <[email protected]> Cc: Will Deacon <[email protected]> Cc: [email protected] Signed-off-by: Stafford Horne <[email protected]> Signed-off-by: Will Deacon <[email protected]>
2017-03-20ALSA: hda - add support for docking station for HP 840 G3Jaroslav Kysela1-0/+11
This tested patch adds missing initialization for Line-In/Out PINs for the docking station for HP 840 G3. Signed-off-by: Jaroslav Kysela <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2017-03-20ALSA: hda - add support for docking station for HP 820 G2Jaroslav Kysela1-1/+13
This tested patch adds missing initialization for Line-In/Out PINs for the docking station for HP 820 G2. Signed-off-by: Jaroslav Kysela <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2017-03-20m68k: Wire up statxGeert Uytterhoeven3-1/+3
Signed-off-by: Geert Uytterhoeven <[email protected]>
2017-03-20m68k/defconfig: Update defconfigs for v4.11-rc1Geert Uytterhoeven12-12/+156
Signed-off-by: Geert Uytterhoeven <[email protected]>
2017-03-20m68k/bitops: Correct signature of test_bit()Geert Uytterhoeven1-1/+1
mm/filemap.c: In function ‘clear_bit_unlock_is_negative_byte’: mm/filemap.c:933: warning: passing argument 2 of ‘test_bit’ discards qualifiers from pointer target type Make the bitmask pointed to by the "vaddr" parameter volatile to fix this, like is done on other architectures. Signed-off-by: Geert Uytterhoeven <[email protected]>
2017-03-20Merge tag 'gvt-fixes-2017-03-17' of https://github.com/01org/gvt-linux into ↵Jani Nikula15-178/+268
drm-intel-fixes gvt-fixes-2017-03-17 - force_nonpriv reg handling in cmd parser (Yan) - gvt error message cleanup (Tina) - i915_wait_request fix from Chris - KVM srcu warning fix (Changbin) - ensure shadow ctx pinned (Chuanxiao) - critical gvt scheduler interval time fix (Zhenyu) - etc. Signed-off-by: Jani Nikula <[email protected]>
2017-03-20powerpc/64s: Fix idle wakeup potential to clobber registersNicholas Piggin1-3/+17
We concluded there may be a window where the idle wakeup code could get to pnv_wakeup_tb_loss() (which clobbers non-volatile GPRs), but the hardware may set SRR1[46:47] to 01b (no state loss) which would result in the wakeup code failing to restore non-volatile GPRs. I was not able to trigger this condition with trivial tests on real hardware or simulator, but the ISA (at least 2.07) seems to allow for it, and Gautham says that it can happen if there is an exception pending when the sleep/winkle instruction is executed. Fixes: 1706567117ba ("powerpc/kvm: make hypervisor state restore a function") Cc: [email protected] # v4.8+ Signed-off-by: Nicholas Piggin <[email protected]> Acked-by: Gautham R. Shenoy <[email protected]> Signed-off-by: Michael Ellerman <[email protected]>
2017-03-20clk: sunxi-ng: fix recalc_rate formula of NKMP clocksIcenowy Zheng1-1/+1
In commit e66f81bbd746 ("clk: sunxi-ng: Implement factors offsets"), the final formula of NKMP clocks' recalc_rate is refactored; however, the refactored formula broke the calculation due to some C language operand priority problem -- the priority of operand >> is lower than * and /, makes the formula being parsed as "(parent_rate * n * k) >> (p / m)", but it should be "(parent_rate * n * k >> p) / m". Add the pair of parentheses to fix up this issue. This pair of parentheses used to exist in the old formula. Fixes: e66f81bbd746 ("clk: sunxi-ng: Implement factors offsets") Signed-off-by: Icenowy Zheng <[email protected]> Signed-off-by: Maxime Ripard <[email protected]>
2017-03-20cxl: Route eeh events to all slices for pci_channel_io_perm_failure stateVaibhav Jain1-7/+6
Fix a boundary condition where in some cases an eeh event with state == pci_channel_io_perm_failure wont be passed on to a driver attached to the virtual PCI device associated with a slice. This will happen in case the slice just before (n-1) doesn't have any vPHB bus associated with it, that results in an early return from cxl_pci_error_detected() callback. With state == pci_channel_io_perm_failure, the adapter will be removed irrespective of the return value of cxl_vphb_error_detected(). So we now always return PCI_ERS_RESULT_DISCONNECTED for this case i.e even if the AFU isn't using a vPHB (currently returns PCI_ERS_RESULT_NONE). Fixes: e4f5fc001a6("cxl: Do not create vPHB if there are no AFU configuration records") Signed-off-by: Vaibhav Jain <[email protected]> Reviewed-by: Matthew R. Ochs <[email protected]> Reviewed-by: Andrew Donnellan <[email protected]> Acked-by: Frederic Barrat <[email protected]> Signed-off-by: Michael Ellerman <[email protected]>
2017-03-20ALSA: ctxfi: Fix the incorrect check of dma_set_mask() callTakashi Iwai1-1/+1
In the commit [15c75b09f8d1: ALSA: ctxfi: Fallback DMA mask to 32bit], I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while cthw20k2.c is OK). This patch fixes that obvious bug. (As a side note: although the original commit was completely wrong, it's still working for most of machines, as it sets to 32bit DMA mask in the end. So the bug severity is low.) Fixes: 15c75b09f8d1 ("ALSA: ctxfi: Fallback DMA mask to 32bit") Cc: <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2017-03-20clk: sunxi-ng: Fix div/mult settings for osc12M on A64Philipp Tomsich1-1/+1
The mult/div for osc12M was previously backwards (giving a 48M rate for osc12M). Fix it. Signed-off-by: Philipp Tomsich <[email protected]> Tested-by: Christoph Muellner <[email protected]> Signed-off-by: Maxime Ripard <[email protected]>
2017-03-20ARM: sun8i: a23/a33: drop bl_en_pin GPIO pinmux in reference design DTSIIcenowy Zheng1-7/+0
The bl_en_pin GPIO pinmux is configured as "gpio_in", which makes it conflicts with the real GPIO usage (out), and makes the backlight not usable. Drop the GPIO pinmux for it, thus this GPIO can be correctly used. Signed-off-by: Icenowy Zheng <[email protected]> Signed-off-by: Maxime Ripard <[email protected]>
2017-03-20ARM: dts: sun7i: lamobo-r1: Fix CPU port RGMII settingsFlorian Fainelli1-1/+1
The CPU port of the BCM53125 is configured with RGMII (no delays) but this should actually be RGMII with transmit delay (rgmii-txid) because STMMAC takes care of inserting the transmitter delay. This fixes occasional packet loss encountered. Fixes: d7b9eaff5f0c ("ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board") Reported-by: Hartmut Knaack <[email protected]> Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: Maxime Ripard <[email protected]>
2017-03-19Linux 4.11-rc3Linus Torvalds1-1/+1
2017-03-19mm/swap: don't BUG_ON() due to uninitialized swap slot cacheLinus Torvalds1-1/+1
This BUG_ON() triggered for me once at shutdown, and I don't see a reason for the check. The code correctly checks whether the swap slot cache is usable or not, so an uninitialized swap slot cache is not actually problematic afaik. I've temporarily just switched the BUG_ON() to a WARN_ON_ONCE(), since I'm not sure why that seemingly pointless check was there. I suspect the real fix is to just remove it entirely, but for now we'll warn about it but not bring the machine down. Cc: "Huang, Ying" <[email protected]> Cc: Tim Chen <[email protected]> Cc: Michal Hocko <[email protected]> Cc: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2017-03-19Merge tag 'powerpc-4.11-5' of ↵Linus Torvalds4-2/+6
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull more powerpc fixes from Michael Ellerman: "A couple of minor powerpc fixes for 4.11: - wire up statx() syscall - don't print a warning on memory hotplug when HPT resizing isn't available Thanks to: David Gibson, Chandan Rajendra" * tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/pseries: Don't give a warning when HPT resizing isn't available powerpc: Wire up statx() syscall
2017-03-19Merge branch 'parisc-4.11-2' of ↵Linus Torvalds8-68/+88
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux Pull parisc fixes from Helge Deller: - Mikulas Patocka added support for R_PARISC_SECREL32 relocations in modules with CONFIG_MODVERSIONS. - Dave Anglin optimized the cache flushing for vmap ranges. - Arvind Yadav provided a fix for a potential NULL pointer dereference in the parisc perf code (and some code cleanups). - I wired up the new statx system call, fixed some compiler warnings with the access_ok() macro and fixed shutdown code to really halt a system at shutdown instead of crashing & rebooting. * 'parisc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: parisc: Fix system shutdown halt parisc: perf: Fix potential NULL pointer dereference parisc: Avoid compiler warnings with access_ok() parisc: Wire up statx system call parisc: Optimize flush_kernel_vmap_range and invalidate_kernel_vmap_range parisc: support R_PARISC_SECREL32 relocation in modules
2017-03-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pendingLinus Torvalds25-548/+1274
Pull SCSI target fixes from Nicholas Bellinger: "The bulk of the changes are in qla2xxx target driver code to address various issues found during Cavium/QLogic's internal testing (stable CC's included), along with a few other stability and smaller miscellaneous improvements. There are also a couple of different patch sets from Mike Christie, which have been a result of his work to use target-core ALUA logic together with tcm-user backend driver. Finally, a patch to address some long standing issues with pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices, which will make folks using physical (or virtual) magnetic tape happy" * git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits) qla2xxx: Update driver version to 9.00.00.00-k qla2xxx: Fix delayed response to command for loop mode/direct connect. qla2xxx: Change scsi host lookup method. qla2xxx: Add DebugFS node to display Port Database qla2xxx: Use IOCB interface to submit non-critical MBX. qla2xxx: Add async new target notification qla2xxx: Export DIF stats via debugfs qla2xxx: Improve T10-DIF/PI handling in driver. qla2xxx: Allow relogin to proceed if remote login did not finish qla2xxx: Fix sess_lock & hardware_lock lock order problem. qla2xxx: Fix inadequate lock protection for ABTS. qla2xxx: Fix request queue corruption. qla2xxx: Fix memory leak for abts processing qla2xxx: Allow vref count to timeout on vport delete. tcmu: Convert cmd_time_out into backend device attribute tcmu: make cmd timeout configurable tcmu: add helper to check if dev was configured target: fix race during implicit transition work flushes target: allow userspace to set state to transitioning target: fix ALUA transition timeout handling ...
2017-03-19Merge branch 'libnvdimm-fixes' of ↵Linus Torvalds1-3/+30
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm Pull device-dax fixes from Dan Williams: "The device-dax driver was not being careful to handle falling back to smaller fault-granularity sizes. The driver already fails fault attempts that are smaller than the device's alignment, but it also needs to handle the cases where a larger page mapping could be established. For simplicity of the immediate fix the implementation just signals VM_FAULT_FALLBACK until fault-size == device-alignment. One fix is for -stable to address pmd-to-pte fallback from the original implementation, another fix is for the new (introduced in 4.11-rc1) pud-to-pmd regression, and a typo fix comes along for the ride. These have received a build success notification from the kbuild robot" * 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: device-dax: fix debug output typo device-dax: fix pud fault fallback handling device-dax: fix pmd/pte fault fallback handling
2017-03-19iio: imu: st_lsm6dsx: fix FIFO_CTRL2 overwrite during watermark configurationLorenzo Bianconi1-2/+2
Fixes: 290a6ce11d93 (iio: imu: add support to lsm6dsx driver) Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Jonathan Cameron <[email protected]>
2017-03-18qla2xxx: Update driver version to 9.00.00.00-kHimanshu Madhani1-3/+3
Signed-off-by: Himanshu Madhani <[email protected]> signed-off-by: Giridhar Malavali <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Fix delayed response to command for loop mode/direct connect.Quinn Tran6-20/+81
Current driver wait for FW to be in the ready state before processing in-coming commands. For Arbitrated Loop or Point-to- Point (not switch), FW Ready state can take a while. FW will transition to ready state after all Nports have been logged in. In the mean time, certain initiators have completed the login and starts IO. Driver needs to start processing all queues if FW is already started. Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Change scsi host lookup method.Quinn Tran7-40/+100
For target mode, when new scsi command arrive, driver first performs a look up of the SCSI Host. The current look up method is based on the ALPA portion of the NPort ID. For Cisco switch, the ALPA can not be used as the index. Instead, the new search method is based on the full value of the Nport_ID via btree lib. Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Add DebugFS node to display Port DatabaseHimanshu Madhani2-4/+90
Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Giridhar Malavali <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Use IOCB interface to submit non-critical MBX.Quinn Tran6-65/+279
The Mailbox interface is currently over subscribed. We like to reserve the Mailbox interface for the chip managment and link initialization. Any non essential Mailbox command will be routed through the IOCB interface. The IOCB interface is able to absorb more commands. Following commands are being routed through IOCB interface - Get ID List (007Ch) - Get Port DB (0064h) - Get Link Priv Stats (006Dh) Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Add async new target notificationQuinn Tran2-3/+4
Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Export DIF stats via debugfsAnil Gurumurthy2-0/+27
Signed-off-by: Anil Gurumurthy <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Improve T10-DIF/PI handling in driver.Quinn Tran7-251/+406
Add routines to support T10 DIF tag. Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Anil Gurumurthy <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Allow relogin to proceed if remote login did not finishQuinn Tran4-8/+32
If the remote port have started the login process, then the PLOGI and PRLI should be back to back. Driver will allow the remote port to complete the process. For the case where the remote port decide to back off from sending PRLI, this local port sets an expiration timer for the PRLI. Once the expiration time passes, the relogin retry logic is allowed to go through and perform login with the remote port. Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Fix sess_lock & hardware_lock lock order problem.Quinn Tran1-23/+18
The main lock that needs to be held for CMD or TMR submission to upper layer is the sess_lock. The sess_lock is used to serialize cmd submission and session deletion. The addition of hardware_lock being held is not necessary. This patch removes hardware_lock dependency from CMD/TMR submission. Use hardware_lock only for error response in this case. Path1 CPU0 CPU1 ---- ---- lock(&(&ha->tgt.sess_lock)->rlock); lock(&(&ha->hardware_lock)->rlock); lock(&(&ha->tgt.sess_lock)->rlock); lock(&(&ha->hardware_lock)->rlock); Path2/deadlock *** DEADLOCK *** Call Trace: dump_stack+0x85/0xc2 print_circular_bug+0x1e3/0x250 __lock_acquire+0x1425/0x1620 lock_acquire+0xbf/0x210 _raw_spin_lock_irqsave+0x53/0x70 qlt_sess_work_fn+0x21d/0x480 [qla2xxx] process_one_work+0x1f4/0x6e0 Cc: <[email protected]> Cc: Bart Van Assche <[email protected]> Reported-by: Bart Van Assche <[email protected]> Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Fix inadequate lock protection for ABTS.Quinn Tran1-2/+10
Normally, ABTS is sent to Target Core as Task MGMT command. In the case of error, qla2xxx needs to send response, hardware_lock is required to prevent request queue corruption. Cc: <[email protected]> Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Fix request queue corruption.Quinn Tran1-3/+9
When FW notify driver or driver detects low FW resource, driver tries to send out Busy SCSI Status to tell Initiator side to back off. During the send process, the lock was not held. Cc: <[email protected]> Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Fix memory leak for abts processingQuinn Tran1-0/+2
Cc: <[email protected]> Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2017-03-18qla2xxx: Allow vref count to timeout on vport delete.Joe Carnuccio5-10/+16
Cc: <[email protected]> Signed-off-by: Joe Carnuccio <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.