aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2017-03-22fjes: Do not load fjes driver if extended socket device is not power on.Yasuaki Ishimatsu1-0/+24
The extended device socket cannot turn on/off while system is running. So when system boots up and the device is not power on, the fjes driver does not need be loaded. To check the status of the device, the patch adds ACPI _STA method check. Signed-off-by: Yasuaki Ishimatsu <[email protected]> CC: Taku Izumi <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22fjes: Do not load fjes driver if system does not have extended socket device.Yasuaki Ishimatsu1-5/+47
The fjes driver is used only by FUJITSU servers and almost of all servers in the world never use it. But currently if ACPI PNP0C02 is defined in the ACPI table, the following message is always shown: "FUJITSU Extended Socket Network Device Driver - version 1.2 - Copyright (c) 2015 FUJITSU LIMITED" The message makes users confused because there is no reason that the message is shown in other vendor servers. To avoid the confusion, the patch adds a check that the server has a extended socket device or not. Signed-off-by: Yasuaki Ishimatsu <[email protected]> CC: Taku Izumi <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22Merge branch 'mlx5-fixes'David S. Miller10-37/+94
Saeed Mahameed says: ==================== Mellanox mlx5 fixes 2017-03-21 This series contains some mlx5 core and ethernet driver fixes. For -stable: net/mlx5e: Count LRO packets correctly (for kernel >= 4.2) net/mlx5e: Count GSO packets correctly (for kernel >= 4.2) net/mlx5: Increase number of max QPs in default profile (for kernel >= 4.0) net/mlx5e: Avoid supporting udp tunnel port ndo for VF reps (for kernel >= 4.10) net/mlx5e: Use the proper UAPI values when offloading TC vlan actions (for kernel >= v4.9) net/mlx5: E-Switch, Don't allow changing inline mode when flows are configured (for kernel >= 4.10) net/mlx5e: Change the TC offload rule add/del code path to be per NIC or E-Switch (for kernel >= 4.10) net/mlx5: Add missing entries for set/query rate limit commands (for kernel >= 4.8) ==================== Signed-off-by: David S. Miller <[email protected]>
2017-03-22net/mlx5e: Count LRO packets correctlyGal Pressman1-0/+4
RX packets statistics ('rx_packets' counter) used to count LRO packets as one, even though it contains multiple segments. This patch will increment the counter by the number of segments, and align the driver with the behavior of other drivers in the stack. Note that no information is lost in this patch due to 'rx_lro_packets' counter existence. Before, ethtool showed: $ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets" rx_packets: 435277 rx_lro_packets: 35847 rx_packets_phy: 1935066 Now, we will see the more logical statistics: $ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets" rx_packets: 1935066 rx_lro_packets: 35847 rx_packets_phy: 1935066 Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files") Signed-off-by: Gal Pressman <[email protected]> Cc: [email protected] Signed-off-by: Saeed Mahameed <[email protected]> Acked-by: Alexei Starovoitov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22net/mlx5e: Count GSO packets correctlyGal Pressman1-2/+3
TX packets statistics ('tx_packets' counter) used to count GSO packets as one, even though it contains multiple segments. This patch will increment the counter by the number of segments, and align the driver with the behavior of other drivers in the stack. Note that no information is lost in this patch due to 'tx_tso_packets' counter existence. Before, ethtool showed: $ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets" tx_packets: 61340 tx_tso_packets: 60954 tx_packets_phy: 2451115 Now, we will see the more logical statistics: $ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets" tx_packets: 2451115 tx_tso_packets: 60954 tx_packets_phy: 2451115 Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files") Signed-off-by: Gal Pressman <[email protected]> Cc: [email protected] Signed-off-by: Saeed Mahameed <[email protected]> Acked-by: Alexei Starovoitov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22net/mlx5: Increase number of max QPs in default profileMaor Gottlieb1-1/+1
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a limit preventing some applications to allocate needed QPs amount. Double the size to 256K. Fixes: e126ba97dba9e ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Maor Gottlieb <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22net/mlx5e: Avoid supporting udp tunnel port ndo for VF repsPaul Blakey4-12/+11
This was added to allow the TC offloading code to identify offloading encap/decap vxlan rules. The VF reps are effectively related to the same mlx5 PCI device as the PF. Since the kernel invokes the (say) delete ndo for each netdev, the FW erred on multiple vxlan dst port deletes when the port was deleted from the system. We fix that by keeping the registration to be carried out only by the PF. Since the PF serves as the uplink device, the VF reps will look up a port there and realize if they are ok to offload that. Tested: <SETUP VFS> <SETUP switchdev mode to have representors> ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999 ip link set vxlan1 up ip link del dev vxlan1 Fixes: 4a25730eb202 ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors') Signed-off-by: Paul Blakey <[email protected]> Reviewed-by: Or Gerlitz <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22net/mlx5e: Use the proper UAPI values when offloading TC vlan actionsOr Gerlitz1-2/+4
Currently we use the non UAPI values and we miss erring on the modify action which is not supported, fix that. Fixes: 8b32580df1cb ('net/mlx5e: Add TC vlan action for SRIOV offloads') Signed-off-by: Or Gerlitz <[email protected]> Reported-by: Petr Machata <[email protected]> Reviewed-by: Jiri Pirko <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22net/mlx5: E-Switch, Don't allow changing inline mode when flows are configuredRoi Dayan2-0/+9
Changing the eswitch inline mode can potentially cause already configured flows not to match the policy. E.g. set policy L4, add some L4 rules, set policy to L2 --> bad! Hence we disallow it. Keep track of how many offloaded rules are now set and refuse inline mode changes if this isn't zero. Fixes: bffaa916588e ("net/mlx5: E-Switch, Add control for inline mode") Signed-off-by: Roi Dayan <[email protected]> Reviewed-by: Or Gerlitz <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22net/mlx5e: Change the TC offload rule add/del code path to be per NIC or ↵Or Gerlitz3-20/+58
E-Switch Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch offloading use case, and push the latter into the e-switch code. This provides better separation and is to be used in down-stream patch for applying a fix. Fixes: bffaa916588e ("net/mlx5: E-Switch, Add control for inline mode") Signed-off-by: Or Gerlitz <[email protected]> Reviewed-by: Roi Dayan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22net/mlx5: Add missing entries for set/query rate limit commandsOr Gerlitz1-0/+4
The switch cases for the rate limit set and query commands were missing, which could get us wrong under fw error or driver reset flow, fix that. Fixes: 1466cc5b23d1 ('net/mlx5: Rate limit tables support') Signed-off-by: Or Gerlitz <[email protected]> Reviewed-by: Hadar Hen Zion <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22Merge tag 'wireless-drivers-for-davem-2017-03-21' of ↵David S. Miller8-55/+57
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for 4.11 iwlwifi * fix a user reported warning in DQA mwifiex * fix a potential double free * fix lost early debug logs * fix init wakeup warning message from device framework * add Ganapathi and Xinming as maintainers ath10k * fix regression with QCA6174 during resume and firmware crash ==================== Signed-off-by: David S. Miller <[email protected]>
2017-03-22tipc: fix nametbl deadlock at tipc_nametbl_unsubscribeYing Xue1-1/+6
Until now, tipc_nametbl_unsubscribe() is called at subscriptions reference count cleanup. Usually the subscriptions cleanup is called at subscription timeout or at subscription cancel or at subscriber delete. We have ignored the possibility of this being called from other locations, which causes deadlock as we try to grab the tn->nametbl_lock while holding it already. CPU1: CPU2: ---------- ---------------- tipc_nametbl_publish spin_lock_bh(&tn->nametbl_lock) tipc_nametbl_insert_publ tipc_nameseq_insert_publ tipc_subscrp_report_overlap tipc_subscrp_get tipc_subscrp_send_event tipc_close_conn tipc_subscrb_release_cb tipc_subscrb_delete tipc_subscrp_put tipc_subscrp_put tipc_subscrp_kref_release tipc_nametbl_unsubscribe spin_lock_bh(&tn->nametbl_lock) <<grab nametbl_lock again>> CPU1: CPU2: ---------- ---------------- tipc_nametbl_stop spin_lock_bh(&tn->nametbl_lock) tipc_purge_publications tipc_nameseq_remove_publ tipc_subscrp_report_overlap tipc_subscrp_get tipc_subscrp_send_event tipc_close_conn tipc_subscrb_release_cb tipc_subscrb_delete tipc_subscrp_put tipc_subscrp_put tipc_subscrp_kref_release tipc_nametbl_unsubscribe spin_lock_bh(&tn->nametbl_lock) <<grab nametbl_lock again>> In this commit, we advance the calling of tipc_nametbl_unsubscribe() from the refcount cleanup to the intended callers. Fixes: d094c4d5f5c7 ("tipc: add subscription refcount to avoid invalid delete") Reported-by: John Thompson <[email protected]> Acked-by: Jon Maloy <[email protected]> Signed-off-by: Ying Xue <[email protected]> Signed-off-by: Parthasarathy Bhuvaragan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22sctp: remove useless err from sctp_association_initXin Long1-4/+2
This patch is to remove the unnecessary temporary variable 'err' from sctp_association_init. Signed-off-by: Xin Long <[email protected]> Acked-by: Neil Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22sctp: declare struct sctp_stream before using itXin Long1-0/+1
sctp_stream_free uses struct sctp_stream as a param, but struct sctp_stream is defined after it's declaration. This patch is to declare struct sctp_stream before sctp_stream_free. Fixes: a83863174a61 ("sctp: prepare asoc stream for stream reconf") Signed-off-by: Xin Long <[email protected]> Acked-by: Neil Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22cpsw/netcp: cpts depends on posix_timersArnd Bergmann1-1/+1
With posix timers having become optional, we get a build error with the cpts time sync option of the CPSW driver: drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts': drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration] This adds a hard dependency on PTP_CLOCK to avoid the problem, as building it without PTP support makes no sense anyway. Fixes: baa73d9e478f ("posix-timers: Make them configurable") Cc: Nicolas Pitre <[email protected]> Cc: [email protected] Signed-off-by: Arnd Bergmann <[email protected]> Acked-by: Nicolas Pitre <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22cpsw/netcp: work around reverse cpts dependencyArnd Bergmann2-2/+8
The dependency is reversed: cpsw and netcp call into cpts, but cpts depends on the other two in Kconfig. This can lead to cpts being a loadable module and its callers built-in: drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove': cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release' drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler': cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp' drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler': cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp' drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop': As a workaround, I'm introducing another Kconfig symbol to control the compilation of cpts, while making the actual module controlled by a silent symbol that is =y when necessary. Fixes: 6246168b4a38 ("net: ethernet: ti: netcp: add support of cpts") Signed-off-by: Arnd Bergmann <[email protected]> Reviewed-by: Grygorii Strashko <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22Merge branch 'r8152-rx-settings'David S. Miller1-7/+16
Hayes Wang says: ==================== r8152: fix the rx settings of RTL8153 The RMS and the rx early size should base on the same rx size. However, the RMS is set to 9K bytes now and the rx early depends on mtu. For using the rx buffer effectively, sync the two settings according to the mtu. ==================== Signed-off-by: David S. Miller <[email protected]>
2017-03-22r8152: fix the rx early size of RTL8153hayeswang1-3/+4
revert commit a59e6d815226 ("r8152: correct the rx early size") and fix the rx early size as (rx buffer size - rx packet size - rx desc size - alignment) / 4 Signed-off-by: Hayes Wang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22r8152: set the RMS of RTL8153 according to the mtuhayeswang1-4/+12
Set the received maximum size (RMS) according to the mtu size. It is unnecessary to receive a packet which is more than the size we could transmit. Besides, this could let the rx buffer be used effectively. Signed-off-by: Hayes Wang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22cgroup, net_cls: iterate the fds of only the tasks which are being migratedTejun Heo1-16/+16
The net_cls controller controls the classid field of each socket which is associated with the cgroup. Because the classid is per-socket attribute, when a task migrates to another cgroup or the configured classid of the cgroup changes, the controller needs to walk all sockets and update the classid value, which was implemented by 3b13758f51de ("cgroups: Allow dynamically changing net_classid"). While the approach is not scalable, migrating tasks which have a lot of fds attached to them is rare and the cost is born by the ones initiating the operations. However, for simplicity, both the migration and classid config change paths call update_classid() which scans all fds of all tasks in the target css. This is an overkill for the migration path which only needs to cover a much smaller subset of tasks which are actually getting migrated in. On cgroup v1, this can lead to unexpected scalability issues when one tries to migrate a task or process into a net_cls cgroup which already contains a lot of fds. Even if the migration traget doesn't have many to get scanned, update_classid() ends up scanning all fds in the target cgroup which can be extremely numerous. Unfortunately, on cgroup v2 which doesn't use net_cls, the problem is even worse. Before bfc2cf6f61fc ("cgroup: call subsys->*attach() only for subsystems which are actually affected by migration"), cgroup core would call the ->css_attach callback even for controllers which don't see actual migration to a different css. As net_cls is always disabled but still mounted on cgroup v2, whenever a process is migrated on the cgroup v2 hierarchy, net_cls sees identity migration from root to root and cgroup core used to call ->css_attach callback for those. The net_cls ->css_attach ends up calling update_classid() on the root net_cls css to which all processes on the system belong to as the controller isn't used. This makes any cgroup v2 migration O(total_number_of_fds_on_the_system) which is horrible and easily leads to noticeable stalls triggering RCU stall warnings and so on. The worst symptom is already fixed in upstream by bfc2cf6f61fc ("cgroup: call subsys->*attach() only for subsystems which are actually affected by migration"); however, backporting that commit is too invasive and we want to avoid other cases too. This patch updates net_cls's cgrp_attach() to iterate fds of only the processes which are actually getting migrated. This removes the surprising migration cost which is dependent on the total number of fds in the target cgroup. As this leaves write_classid() the only user of update_classid(), open-code the helper into write_classid(). Reported-by: David Goode <[email protected]> Fixes: 3b13758f51de ("cgroups: Allow dynamically changing net_classid") Cc: [email protected] # v4.4+ Cc: Nina Schiff <[email protected]> Cc: David S. Miller <[email protected]> Signed-off-by: Tejun Heo <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22arm64: dts: NS2: Add dma-coherent to relevant DT entriesJon Mason1-0/+11
Cache related issues with DMA rings and performance issues related to caching are being caused by not properly setting the "dma-coherent" flag in the device tree entries. Adding it here to correct the issue. Signed-off-by: Jon Mason <[email protected]> Fixes: fd5e5dd56 ("arm64: dts: Add PCIe0 and PCIe4 DT nodes for NS2") Fixes: dddc3c9d7 ("arm64: dts: NS2: add AMAC ethernet support") Fixes: e79249143 ("arm64: dts: Add Broadcom Northstar2 device tree entries for PDC driver") Fixes: ac9aae00f ("arm64: dts: Add SATA3 AHCI and SATA3 PHY DT nodes for NS2") Fixes: efc877676 ("arm64: dts: Add SDHCI DT node for NS2") Signed-off-by: Florian Fainelli <[email protected]>
2017-03-22arm64: kaslr: Fix up the kernel image alignmentNeeraj Upadhyay1-3/+7
If kernel image extends across alignment boundary, existing code increases the KASLR offset by size of kernel image. The offset is masked after resizing. There are cases, where after masking, we may still have kernel image extending across boundary. This eventually results in only 2MB block getting mapped while creating the page tables. This results in data aborts while accessing unmapped regions during second relocation (with kaslr offset) in __primary_switch. To fix this problem, round up the kernel image size, by swapper block size, before adding it for correction. For example consider below case, where kernel image still crosses 1GB alignment boundary, after masking the offset, which is fixed by rounding up kernel image size. SWAPPER_TABLE_SHIFT = 30 Swapper using section maps with section size 2MB. CONFIG_PGTABLE_LEVELS = 3 VA_BITS = 39 _text : 0xffffff8008080000 _end : 0xffffff800aa1b000 offset : 0x1f35600000 mask = ((1UL << (VA_BITS - 2)) - 1) & ~(SZ_2M - 1) (_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c (_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d offset after existing correction (before mask) = 0x1f37f9b000 (_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d (_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d offset (after mask) = 0x1f37e00000 (_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c (_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d new offset w/ rounding up = 0x1f38000000 (_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d (_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d Fixes: f80fb3a3d508 ("arm64: add support for kernel ASLR") Cc: <[email protected]> Reviewed-by: Ard Biesheuvel <[email protected]> Signed-off-by: Neeraj Upadhyay <[email protected]> Signed-off-by: Srinivas Ramana <[email protected]> Signed-off-by: Will Deacon <[email protected]>
2017-03-22iommu: Disambiguate MSI region typesRobin Murphy7-15/+23
The introduction of reserved regions has left a couple of rough edges which we could do with sorting out sooner rather than later. Since we are not yet addressing the potential dynamic aspect of software-managed reservations and presenting them at arbitrary fixed addresses, it is incongruous that we end up displaying hardware vs. software-managed MSI regions to userspace differently, especially since ARM-based systems may actually require one or the other, or even potentially both at once, (which iommu-dma currently has no hope of dealing with at all). Let's resolve the former user-visible inconsistency ASAP before the ABI has been baked into a kernel release, in a way that also lays the groundwork for the latter shortcoming to be addressed by follow-up patches. For clarity, rename the software-managed type to IOMMU_RESV_SW_MSI, use IOMMU_RESV_MSI to describe the hardware type, and document everything a little bit. Since the x86 MSI remapping hardware falls squarely under this meaning of IOMMU_RESV_MSI, apply that type to their regions as well, so that we tell the same story to userspace across all platforms. Secondly, as the various region types require quite different handling, and it really makes little sense to ever try combining them, convert the bitfield-esque #defines to a plain enum in the process before anyone gets the wrong impression. Fixes: d30ddcaa7b02 ("iommu: Add a new type field in iommu_resv_region") Reviewed-by: Eric Auger <[email protected]> CC: Alex Williamson <[email protected]> CC: David Woodhouse <[email protected]> CC: [email protected] Signed-off-by: Robin Murphy <[email protected]> Signed-off-by: Joerg Roedel <[email protected]>
2017-03-22iommu/exynos: Workaround FLPD cache flush issues for SYSMMU v5Marek Szyprowski1-1/+4
For some unknown reasons, in some cases, FLPD cache invalidation doesn't work properly with SYSMMU v5 controllers found in Exynos5433 SoCs. This can be observed by a firmware crash during initialization phase of MFC video decoder available in the mentioned SoCs when IOMMU support is enabled. To workaround this issue perform a full TLB/FLPD invalidation in case of replacing any first level page descriptors in case of SYSMMU v5. Fixes: 740a01eee9ada ("iommu/exynos: Add support for v5 SYSMMU") CC: [email protected] # v4.10+ Signed-off-by: Marek Szyprowski <[email protected]> Tested-by: Andrzej Hajda <[email protected]> Signed-off-by: Joerg Roedel <[email protected]>
2017-03-22iommu/exynos: Block SYSMMU while invalidating FLPD cacheMarek Szyprowski1-1/+4
Documentation specifies that SYSMMU should be in blocked state while performing TLB/FLPD cache invalidation, so add needed calls to sysmmu_block/unblock. Fixes: 66a7ed84b345d ("iommu/exynos: Apply workaround of caching fault page table entries") CC: [email protected] # v4.10+ Signed-off-by: Marek Szyprowski <[email protected]> Signed-off-by: Joerg Roedel <[email protected]>
2017-03-22blk-mq: don't complete un-started request in timeout handlerMing Lei1-10/+1
When iterating busy requests in timeout handler, if the STARTED flag of one request isn't set, that means the request is being processed in block layer or driver, and isn't submitted to hardware yet. In current implementation of blk_mq_check_expired(), if the request queue becomes dying, un-started requests are handled as being completed/freed immediately. This way is wrong, and can cause rq corruption or double allocation[1][2], when doing I/O and removing&resetting NVMe device at the sametime. This patch fixes several issues reported by Yi Zhang. [1]. oops log 1 [ 581.789754] ------------[ cut here ]------------ [ 581.789758] kernel BUG at block/blk-mq.c:374! [ 581.789760] invalid opcode: 0000 [#1] SMP [ 581.789761] Modules linked in: vfat fat ipmi_ssif intel_rapl sb_edac edac_core x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm nvme irqbypass crct10dif_pclmul nvme_core crc32_pclmul ghash_clmulni_intel intel_cstate ipmi_si mei_me ipmi_devintf intel_uncore sg ipmi_msghandler intel_rapl_perf iTCO_wdt mei iTCO_vendor_support mxm_wmi lpc_ich dcdbas shpchp pcspkr acpi_power_meter wmi nfsd auth_rpcgss nfs_acl lockd dm_multipath grace sunrpc ip_tables xfs libcrc32c sd_mod mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm ahci libahci crc32c_intel tg3 libata megaraid_sas i2c_core ptp fjes pps_core dm_mirror dm_region_hash dm_log dm_mod [ 581.789796] CPU: 1 PID: 1617 Comm: kworker/1:1H Not tainted 4.10.0.bz1420297+ #4 [ 581.789797] Hardware name: Dell Inc. PowerEdge R730xd/072T6D, BIOS 2.2.5 09/06/2016 [ 581.789804] Workqueue: kblockd blk_mq_timeout_work [ 581.789806] task: ffff8804721c8000 task.stack: ffffc90006ee4000 [ 581.789809] RIP: 0010:blk_mq_end_request+0x58/0x70 [ 581.789810] RSP: 0018:ffffc90006ee7d50 EFLAGS: 00010202 [ 581.789811] RAX: 0000000000000001 RBX: ffff8802e4195340 RCX: ffff88028e2f4b88 [ 581.789812] RDX: 0000000000001000 RSI: 0000000000001000 RDI: 0000000000000000 [ 581.789813] RBP: ffffc90006ee7d60 R08: 0000000000000003 R09: ffff88028e2f4b00 [ 581.789814] R10: 0000000000001000 R11: 0000000000000001 R12: 00000000fffffffb [ 581.789815] R13: ffff88042abe5780 R14: 000000000000002d R15: ffff88046fbdff80 [ 581.789817] FS: 0000000000000000(0000) GS:ffff88047fc00000(0000) knlGS:0000000000000000 [ 581.789818] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 581.789819] CR2: 00007f64f403a008 CR3: 000000014d078000 CR4: 00000000001406e0 [ 581.789820] Call Trace: [ 581.789825] blk_mq_check_expired+0x76/0x80 [ 581.789828] bt_iter+0x45/0x50 [ 581.789830] blk_mq_queue_tag_busy_iter+0xdd/0x1f0 [ 581.789832] ? blk_mq_rq_timed_out+0x70/0x70 [ 581.789833] ? blk_mq_rq_timed_out+0x70/0x70 [ 581.789840] ? __switch_to+0x140/0x450 [ 581.789841] blk_mq_timeout_work+0x88/0x170 [ 581.789845] process_one_work+0x165/0x410 [ 581.789847] worker_thread+0x137/0x4c0 [ 581.789851] kthread+0x101/0x140 [ 581.789853] ? rescuer_thread+0x3b0/0x3b0 [ 581.789855] ? kthread_park+0x90/0x90 [ 581.789860] ret_from_fork+0x2c/0x40 [ 581.789861] Code: 48 85 c0 74 0d 44 89 e6 48 89 df ff d0 5b 41 5c 5d c3 48 8b bb 70 01 00 00 48 85 ff 75 0f 48 89 df e8 7d f0 ff ff 5b 41 5c 5d c3 <0f> 0b e8 71 f0 ff ff 90 eb e9 0f 1f 40 00 66 2e 0f 1f 84 00 00 [ 581.789882] RIP: blk_mq_end_request+0x58/0x70 RSP: ffffc90006ee7d50 [ 581.789889] ---[ end trace bcaf03d9a14a0a70 ]--- [2]. oops log2 [ 6984.857362] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010 [ 6984.857372] IP: nvme_queue_rq+0x6e6/0x8cd [nvme] [ 6984.857373] PGD 0 [ 6984.857374] [ 6984.857376] Oops: 0000 [#1] SMP [ 6984.857379] Modules linked in: ipmi_ssif vfat fat intel_rapl sb_edac edac_core x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel ipmi_si iTCO_wdt iTCO_vendor_support mxm_wmi ipmi_devintf intel_cstate sg dcdbas intel_uncore mei_me intel_rapl_perf mei pcspkr lpc_ich ipmi_msghandler shpchp acpi_power_meter wmi nfsd auth_rpcgss dm_multipath nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c sd_mod mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect crc32c_intel sysimgblt fb_sys_fops ttm nvme drm nvme_core ahci libahci i2c_core tg3 libata ptp megaraid_sas pps_core fjes dm_mirror dm_region_hash dm_log dm_mod [ 6984.857416] CPU: 7 PID: 1635 Comm: kworker/7:1H Not tainted 4.10.0-2.el7.bz1420297.x86_64 #1 [ 6984.857417] Hardware name: Dell Inc. PowerEdge R730xd/072T6D, BIOS 2.2.5 09/06/2016 [ 6984.857427] Workqueue: kblockd blk_mq_run_work_fn [ 6984.857429] task: ffff880476e3da00 task.stack: ffffc90002e90000 [ 6984.857432] RIP: 0010:nvme_queue_rq+0x6e6/0x8cd [nvme] [ 6984.857433] RSP: 0018:ffffc90002e93c50 EFLAGS: 00010246 [ 6984.857434] RAX: 0000000000000000 RBX: ffff880275646600 RCX: 0000000000001000 [ 6984.857435] RDX: 0000000000000fff RSI: 00000002fba2a000 RDI: ffff8804734e6950 [ 6984.857436] RBP: ffffc90002e93d30 R08: 0000000000002000 R09: 0000000000001000 [ 6984.857437] R10: 0000000000001000 R11: 0000000000000000 R12: ffff8804741d8000 [ 6984.857438] R13: 0000000000000040 R14: ffff880475649f80 R15: ffff8804734e6780 [ 6984.857439] FS: 0000000000000000(0000) GS:ffff88047fcc0000(0000) knlGS:0000000000000000 [ 6984.857440] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 6984.857442] CR2: 0000000000000010 CR3: 0000000001c09000 CR4: 00000000001406e0 [ 6984.857443] Call Trace: [ 6984.857451] ? mempool_free+0x2b/0x80 [ 6984.857455] ? bio_free+0x4e/0x60 [ 6984.857459] blk_mq_dispatch_rq_list+0xf5/0x230 [ 6984.857462] blk_mq_process_rq_list+0x133/0x170 [ 6984.857465] __blk_mq_run_hw_queue+0x8c/0xa0 [ 6984.857467] blk_mq_run_work_fn+0x12/0x20 [ 6984.857473] process_one_work+0x165/0x410 [ 6984.857475] worker_thread+0x137/0x4c0 [ 6984.857478] kthread+0x101/0x140 [ 6984.857480] ? rescuer_thread+0x3b0/0x3b0 [ 6984.857481] ? kthread_park+0x90/0x90 [ 6984.857489] ret_from_fork+0x2c/0x40 [ 6984.857490] Code: 8b bd 70 ff ff ff 89 95 50 ff ff ff 89 8d 58 ff ff ff 44 89 95 60 ff ff ff e8 b7 dd 12 e1 8b 95 50 ff ff ff 48 89 85 68 ff ff ff <4c> 8b 48 10 44 8b 58 18 8b 8d 58 ff ff ff 44 8b 95 60 ff ff ff [ 6984.857511] RIP: nvme_queue_rq+0x6e6/0x8cd [nvme] RSP: ffffc90002e93c50 [ 6984.857512] CR2: 0000000000000010 [ 6984.895359] ---[ end trace 2d7ceb528432bf83 ]--- Cc: [email protected] Reported-by: Yi Zhang <[email protected]> Tested-by: Yi Zhang <[email protected]> Reviewed-by: Bart Van Assche <[email protected]> Reviewed-by: Hannes Reinecke <[email protected]> Signed-off-by: Ming Lei <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2017-03-22[media] exynos-gsc: Do not swap cb/cr for semi planar formatsThibault Saunier1-2/+0
In the case of semi planar formats cb and cr are in the same plane in memory, meaning that will be set to 'cb' whatever the format is, and whatever the (packed) order of those components are. Suggested-by: Nicolas Dufresne <[email protected]> Signed-off-by: Thibault Saunier <[email protected]> Signed-off-by: Javier Martinez Canillas <[email protected]> Acked-by: Sylwester Nawrocki <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2017-03-22[media] bdisp: Clean up file handle in open() error pathShailendra Verma1-1/+1
The File handle is not yet added in the vdev list.So no need to call v4l2_fh_del(&ctx->fh)if it fails to create control. Signed-off-by: Shailendra Verma <[email protected]> Reviewed-by: Fabien Dessenne <[email protected]> Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2017-03-22[media] coda/imx-vdoa: platform_driver should not be constArnd Bergmann1-1/+1
The device driver platform is actually written to during registration, for setting the owner field, so platform_driver_register() does not take a const pointer: drivers/media/platform/coda/imx-vdoa.c: In function 'vdoa_driver_init': drivers/media/platform/coda/imx-vdoa.c:333:213: error: passing argument 1 of '__platform_driver_register' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers] module_platform_driver(vdoa_driver); In file included from drivers/media/platform/coda/imx-vdoa.c:22:0: include/linux/platform_device.h:199:12: note: expected 'struct platform_driver *' but argument is of type 'const struct platform_driver *' extern int __platform_driver_register(struct platform_driver *, ^~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/media/platform/coda/imx-vdoa.c: In function 'vdoa_driver_exit': drivers/media/platform/coda/imx-vdoa.c:333:626: error: passing argument 1 of 'platform_driver_unregister' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers] Remove the modifier again. Fixes: d2fe28feaebb ("[media] coda/imx-vdoa: constify structs") Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2017-03-22Merge tag 'extcon-fixes-for-4.11-rc3' of ↵Greg Kroah-Hartman3-12/+34
git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-linus Chanwoo writes: Update extcon for v4.11-rc3 This patch fixes issues for Intel INT3496 ACPI device as following: - Propagate error code of gpiod_to_irq(). - Set the ID pin as the input direction if firmware has the bug - Rename the gpio name for bining according to the documentation. - Add gpio acpi mapping table and the dependency on X86. - Use the devm_gpiod_get() instead of gpiod_get_index because of acpi mapping table.
2017-03-22Merge tag 'iio-fixes-for-4.11c' of ↵Greg Kroah-Hartman5-9/+20
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus Jonathan writes: Thirds set of IIO fixes for the 4.11 cycle. * core - iio sw-device - ensure configfs is enabled both when building as module and built in. * ak8974 - drop incorrect __exit markup on remove. * hid-sensor-trigger - code reorganise to avoid losing settings if a power cycle occurs during S3. * lsm6dsx - fix incorrect overwrite of parts of FIFO_CTRL2 register during watermark configuration. * ti-am335x - fix a hard to hit bug when reenabling from a fifo overrun by waiting for current cycle to finish.
2017-03-22iommu/vt-d: Fix NULL pointer dereference in device_to_iommuKoos Vriezen1-1/+1
The function device_to_iommu() in the Intel VT-d driver lacks a NULL-ptr check, resulting in this oops at boot on some platforms: BUG: unable to handle kernel NULL pointer dereference at 00000000000007ab IP: [<ffffffff8132234a>] device_to_iommu+0x11a/0x1a0 PGD 0 [...] Call Trace: ? find_or_alloc_domain.constprop.29+0x1a/0x300 ? dw_dma_probe+0x561/0x580 [dw_dmac_core] ? __get_valid_domain_for_dev+0x39/0x120 ? __intel_map_single+0x138/0x180 ? intel_alloc_coherent+0xb6/0x120 ? sst_hsw_dsp_init+0x173/0x420 [snd_soc_sst_haswell_pcm] ? mutex_lock+0x9/0x30 ? kernfs_add_one+0xdb/0x130 ? devres_add+0x19/0x60 ? hsw_pcm_dev_probe+0x46/0xd0 [snd_soc_sst_haswell_pcm] ? platform_drv_probe+0x30/0x90 ? driver_probe_device+0x1ed/0x2b0 ? __driver_attach+0x8f/0xa0 ? driver_probe_device+0x2b0/0x2b0 ? bus_for_each_dev+0x55/0x90 ? bus_add_driver+0x110/0x210 ? 0xffffffffa11ea000 ? driver_register+0x52/0xc0 ? 0xffffffffa11ea000 ? do_one_initcall+0x32/0x130 ? free_vmap_area_noflush+0x37/0x70 ? kmem_cache_alloc+0x88/0xd0 ? do_init_module+0x51/0x1c4 ? load_module+0x1ee9/0x2430 ? show_taint+0x20/0x20 ? kernel_read_file+0xfd/0x190 ? SyS_finit_module+0xa3/0xb0 ? do_syscall_64+0x4a/0xb0 ? entry_SYSCALL64_slow_path+0x25/0x25 Code: 78 ff ff ff 4d 85 c0 74 ee 49 8b 5a 10 0f b6 9b e0 00 00 00 41 38 98 e0 00 00 00 77 da 0f b6 eb 49 39 a8 88 00 00 00 72 ce eb 8f <41> f6 82 ab 07 00 00 04 0f 85 76 ff ff ff 0f b6 4d 08 88 0e 49 RIP [<ffffffff8132234a>] device_to_iommu+0x11a/0x1a0 RSP <ffffc90001457a78> CR2: 00000000000007ab ---[ end trace 16f974b6d58d0aad ]--- Add the missing pointer check. Fixes: 1c387188c60f53b338c20eee32db055dfe022a9b ("iommu/vt-d: Fix IOMMU lookup for SR-IOV Virtual Functions") Signed-off-by: Koos Vriezen <[email protected]> Cc: [email protected] # 4.8.15+ Signed-off-by: Joerg Roedel <[email protected]>
2017-03-22extcon: int3496: Set the id pin to direction-input if necessaryHans de Goede1-0/+3
With the new more strict ACPI gpio code the dsdt's IoRestriction flags are honored on gpiod_get, but in some dsdt's it is wrong, so explicitly call gpiod_direction_input on the id gpio if necessary. This fixes the following errors when the int3496 code is used together with the new more strict ACPI gpio code: [ 2382.484415] gpio gpiochip1: (INT33FF:01): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ [ 2382.484425] gpio gpiochip1: (INT33FF:01): unable to lock HW IRQ 3 for IRQ [ 2382.484429] genirq: Failed to request resources for INT3496:00 (irq 174) on irqchip chv-gpio [ 2382.484518] intel-int3496 INT3496:00: can't request IRQ for USB ID GPIO: -22 [ 2382.500359] intel-int3496: probe of INT3496:00 failed with error -22 Signed-off-by: Hans de Goede <[email protected]> Reviewed-by: Andy Shevchenko <[email protected]> Signed-off-by: Chanwoo Choi <[email protected]>
2017-03-22extcon: int3496: Use gpiod_get instead of gpiod_get_indexHans de Goede1-9/+3
Now that we've an acpi mapping table we should be using gpiod_get instead of gpiod_get_index. Signed-off-by: Hans de Goede <[email protected]> Reviewed-by: Andy Shevchenko <[email protected]> Signed-off-by: Chanwoo Choi <[email protected]>
2017-03-22extcon: int3496: Add dependency on X86 as it's Intel specificPeter Robinson1-1/+1
Add dependency on X86 so it doesn't show up on other arches and add a option for compile test so it still gets build coverage. Signed-off-by: Peter Robinson <[email protected]> Signed-off-by: Chanwoo Choi <[email protected]>
2017-03-22extcon: int3496: Add GPIO ACPI mapping tableAndy Shevchenko2-0/+25
In order to make GPIO ACPI library stricter prepare users of gpiod_get_index() to correctly behave when there no mapping is provided by firmware. Here we add explicit mapping between _CRS GpioIo() resources and their names used in the driver. Signed-off-by: Andy Shevchenko <[email protected]> Signed-off-by: Chanwoo Choi <[email protected]>
2017-03-22extcon: int3496: Rename GPIO pins in accordance with bindingAndy Shevchenko1-2/+2
Update GPIO pin names in extcon-intel-int3496.c driver to follow the existing extcon binding. Signed-off-by: Andy Shevchenko <[email protected]> Signed-off-by: Chanwoo Choi <[email protected]>
2017-03-22usb: gadget: f_hid: fix: Don't access hidg->req without spinlock heldKrzysztof Opasiak1-4/+4
hidg->req should be accessed only with write_spinlock held as it is set to NULL when we get disabled by host. Signed-off-by: Krzysztof Opasiak <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-03-22usb: gadget: udc: remove pointer dereference after freeGustavo A. R. Silva1-1/+0
Remove pointer dereference after free. Addresses-Coverity-ID: 1091173 Acked-by: Michal Nazarewicz <[email protected]> Signed-off-by: Gustavo A. R. Silva <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-03-22usb: gadget: f_uvc: Sanity check wMaxPacketSize for SuperSpeedRoger Quadros1-0/+8
As per USB3.0 Specification "Table 9-20. Standard Endpoint Descriptor", for interrupt and isochronous endpoints, wMaxPacketSize must be set to 1024 if the endpoint defines bMaxBurst to be greater than zero. Reviewed-by: Laurent Pinchart <[email protected]> Signed-off-by: Roger Quadros <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-03-22usb: gadget: f_uvc: Fix SuperSpeed companion descriptor's wBytesPerIntervalRoger Quadros1-1/+1
The streaming_maxburst module parameter is 0 offset (0..15) so we must add 1 while using it for wBytesPerInterval calculation for the SuperSpeed companion descriptor. Without this host uvcvideo driver will always see the wrong wBytesPerInterval for SuperSpeed uvc gadget and may not find a suitable video interface endpoint. e.g. for streaming_maxburst = 0 case it will always fail as wBytePerInterval was evaluating to 0. Cc: [email protected] Reviewed-by: Laurent Pinchart <[email protected]> Signed-off-by: Roger Quadros <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-03-22usb: gadget: acm: fix endianness in notificationsOliver Neukum1-1/+3
The gadget code exports the bitfield for serial status changes over the wire in its internal endianness. The fix is to convert to little endian before sending it over the wire. Signed-off-by: Oliver Neukum <[email protected]> Tested-by: 家瑋 <[email protected]> CC: <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-03-22usb: dwc3: gadget: delay unmap of bounced requestsJanusz Dziedzic1-4/+17
In the case of bounced ep0 requests, we must delay DMA operation until after ->complete() otherwise we might overwrite contents of req->buf. This caused problems with RNDIS gadget. Signed-off-by: Janusz Dziedzic <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-03-22hwmon: Add missing HWMON_T_ALARMPeter Huewe1-0/+1
Unfortunately the HWMON_T_ALARM define was missing, although the associated entry was present in hwmon_temp_attributes. This is needed to convert drivers to the new interface which use channel based alarms. Signed-off-by: Peter Huewe <[email protected]> Signed-off-by: Guenter Roeck <[email protected]>
2017-03-22hwmon: (it87) Avoid registering the same chip on both SIO addressesGuenter Roeck1-5/+19
IT8705F is known to respond on both SIO addresses. Registering it twice may result in system lockups. Reported-by: Russell King <[email protected]> Fixes: e84bd9535e2b ("hwmon: (it87) Add support for second Super-IO chip") Signed-off-by: Guenter Roeck <[email protected]>
2017-03-22hwmon: (max31790) Set correct PWM valueAlex Hemme1-1/+1
Traced fans not spinning to incorrect PWM value being written. The passed in value was written instead of the calulated value. Fixes: 54187ff9d766 ("hwmon: (max31790) Convert to use new hwmon registration API") Signed-off-by: Alex Hemme <[email protected]> Signed-off-by: Guenter Roeck <[email protected]>
2017-03-21net: qmi_wwan: Add USB IDs for MDM6600 modem on Motorola Droid 4Tony Lindgren1-0/+4
This gets qmicli working with the MDM6600 modem. Cc: Bjørn Mork <[email protected]> Reviewed-by: Sebastian Reichel <[email protected]> Tested-by: Sebastian Reichel <[email protected]> Signed-off-by: Tony Lindgren <[email protected]> Acked-by: Bjørn Mork <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-21selftests/bpf: fix broken build, take 2Zi Shen Lim1-9/+10
Merge of 'linux-kselftest-4.11-rc1': 1. Partially removed use of 'test_objs' target, breaking force rebuild of BPFOBJ, introduced in commit d498f8719a09 ("bpf: Rebuild bpf.o for any dependency update"). Update target so dependency on BPFOBJ is restored. 2. Introduced commit 2047f1d8ba28 ("selftests: Fix the .c linking rule") which fixes order of LDLIBS. Commit d02d8986a768 ("bpf: Always test unprivileged programs") added libcap dependency into CFLAGS. Use LDLIBS instead to fix linking of test_verifier. 3. Introduced commit d83c3ba0b926 ("selftests: Fix selftests build to just build, not run tests"). Reordering the Makefile allows us to remove the 'all' target. Tested both: selftests/bpf$ make and selftests$ make TARGETS=bpf on Ubuntu 16.04.2. Signed-off-by: Zi Shen Lim <[email protected]> Acked-by: Daniel Borkmann <[email protected]> Tested-by: Daniel Borkmann <[email protected]> Acked-by: Alexei Starovoitov <[email protected]> Tested-by: Alexei Starovoitov <[email protected]> Acked-by: Shuah Khan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-21tcp: mark skbs with SCM_TIMESTAMPING_OPT_STATSSoheil Hassas Yeganeh3-7/+14
SOF_TIMESTAMPING_OPT_STATS can be enabled and disabled while packets are collected on the error queue. So, checking SOF_TIMESTAMPING_OPT_STATS in sk->sk_tsflags is not enough to safely assume that the skb contains OPT_STATS data. Add a bit in sock_exterr_skb to indicate whether the skb contains opt_stats data. Fixes: 1c885808e456 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING") Reported-by: JongHwan Kim <[email protected]> Signed-off-by: Soheil Hassas Yeganeh <[email protected]> Signed-off-by: Eric Dumazet <[email protected]> Signed-off-by: Willem de Bruijn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.