| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Up to now we were reading some DRAM information from MCHBAR register
and from pcode what is already not good but some GEN12(TGL-H and ADL-S)
platforms have MCHBAR DRAM information in different offsets.
This was notified to HW team that decided that the best alternative is
always apply the 16gb_dimm watermark adjustment for GEN12+ platforms
and read the remaning DRAM information needed to other display
programming from pcode.
So here moving the DRAM pcode function to intel_dram.c, removing
the duplicated fields from intel_qgv_info, setting and using
information from dram_info.
v2:
- bring back num_points to intel_qgv_info as num_qgv_point can be
overwritten in icl_get_qgv_points()
- add gen12_get_dram_info() and simplify gen11_get_dram_info()
Reviewed-by: Lucas De Marchi <[email protected]>
Signed-off-by: José Roberto de Souza <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Valid, ranks and bandwidth_kbps are set into dram_info but are not
used anywhere else so nuking it.
Reviewed-by: Lucas De Marchi <[email protected]>
Signed-off-by: José Roberto de Souza <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Atm the driver will calculate a wrong MST timeslots/MTP (aka time unit)
value for MST streams if the link parameters (link rate or lane count)
are limited in a way independent of the sink capabilities (reported by
DPCD).
One example of such a limitation is when a MUX between the sink and
source connects only a limited number of lanes to the display and
connects the rest of the lanes to other peripherals (USB).
Another issue is that atm MST core calculates the divider based on the
backwards compatible DPCD (at address 0x0000) vs. the extended
capability info (at address 0x2200). This can result in leaving some
part of the MST BW unused (For instance in case of the WD19TB dock).
Fix the above two issues by calculating the PBN divider value based on
the rate and lane count link parameters that the driver uses for all
other computation.
Bugzilla: https://gitlab.freedesktop.org/drm/intel/-/issues/2977
Cc: Lyude Paul <[email protected]>
Cc: Ville Syrjala <[email protected]>
Cc: <[email protected]>
Signed-off-by: Imre Deak <[email protected]>
Reviewed-by: Ville Syrjala <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
This function will be needed by the next patch where the driver
calculates the BW based on driver specific parameters, so export it.
At the same time sanitize the function params, passing the more natural
link rate instead of the encoding of the same rate.
v2:
- Fix function documentation. (Lyude)
Cc: Lyude Paul <[email protected]>
Cc: Ville Syrjala <[email protected]>
Cc: <[email protected]>
Cc: [email protected]
Signed-off-by: Imre Deak <[email protected]>
Reviewed-by: Lyude Paul <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The HDCP 1.4 spec does not require the QUERY_STREAM_ENCRYPTION_STATUS
check, it was always a nice-to-have. After deploying this across various
devices, we've determined that some MST bridge chips do not properly
support this call for HDCP 1.4 (namely Synaptics and Realtek).
I had considered creating a quirk for this, but I think it's more
prudent to just disable the check entirely since I don't have an idea
how widespread support is.
Changes in v2:
-Rebased on -tip
Acked-by: Daniel Vetter <[email protected]>
Reviewed-by: Anshuman Gupta <[email protected]>
Signed-off-by: Sean Paul <[email protected]>
Signed-off-by: Anshuman Gupta <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] #v1
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Prevent the ICL HDR plane pipeline from performing YUV color range
correction twice when the input is in limited range. This is done by
removing the limited-range code from icl_program_input_csc().
Before this patch the following could happen: user space gives us a YUV
buffer in limited range; per the pipeline in [1], the plane would first
go through a "YUV Range correct" stage that expands the range; the plane
would then go through the "Input CSC" stage which would also expand the
range because icl_program_input_csc() would use a matrix and an offset
that assume limited-range input; this would ultimately cause dark and
light colors to appear darker and lighter than they should respectively.
This is an issue because if a buffer switches between being scanned out
and being composited with the GPU, the user will see a color difference.
If this switching happens quickly and frequently, the user will perceive
this as a flickering.
[1] https://01.org/sites/default/files/documentation/intel-gfx-prm-osrc-icllp-vol12-displayengine_0.pdf#page=281
Cc: [email protected]
Signed-off-by: Andres Calderon Jaramillo <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Inform us if we're buggy and are about to exceed the size of the
bitfields in the plane TILEOFF/OFFSET registers.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Karthik B S <[email protected]>
|
|
DSI transcoder does not support VRR and hence skip the HW state
readout if its a DSI transcoder.
Fixes: c7f0f4372b30 ("drm/i915/display: Add HW state readout for VRR")
Cc: Ville Syrjälä <[email protected]>
Cc: Jani Nikula <[email protected]>
Cc: Vandita Kulkarni <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Readout the dbuf related stuff during driver init/resume and
stick it into our dbuf state.
v2: Keep crtc_state->wm.skl.ddb
Reviewed-by: Stanislav Lisovskiy <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
In order to make the dbuf state computation less fragile
let's make it stand on its own feet by not requiring someone
to peek into a crystall ball ahead of time to figure out
which pipes need to be added to the state under which potential
future conditions. Instead we compute each piece of the state
as we go along, and if any fallout occurs that affects more than
the current set of pipes we add the affected pipes to the state
naturally.
That requires that we track a few extra thigns in the global
dbuf state: dbuf slices for each pipe, and the weight each
pipe has when distributing the same set of slice(s) between
multiple pipes. Easy enough.
We do need to follow a somewhat careful sequence of computations
though as there are several steps involved in cooking up the dbuf
state. Thoguh we could avoid some of that by computing more things
on demand instead of relying on earlier step of the algorithm to
have filled it out. I think the end result is still reasonable
as the entire sequence is pretty much consolidated into a single
function instead of being spread around all over.
The rough sequence is this:
1. calculate active_pipes
2. calculate dbuf slices for every pipe
3. calculate total enabled slices
4. calculate new dbuf weights for any crtc in the state
5. calculate new ddb entry for every pipe based on the sets of
slices and weights, and add any affected crtc to the state
6. calculate new plane ddb entries for all crtcs in the state,
and add any affected plane to the state so that we'll perform
the requisite hw reprogramming
And as a nice bonus we get to throw dev_priv->wm.distrust_bios_wm
out the window.
v2: Keep crtc_state->wm.skl.ddb
Reviewed-by: Stanislav Lisovskiy <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Extract the code to calculate the weights used to chunk up the dbuf
between pipes. There's still extra stuff in there that shouldn't be
there and must be moved out, but that requires a bit more state to
be tracked in the dbuf state.
v2: Keep crtc_state->wm.skl.ddb
Reviewed-by: Stanislav Lisovskiy <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The dbuf state will be where we collect all the inter-pipe dbuf
allocation stuff. Start by adding the actual per-pipe ddb entries
there.
Originally the plan was to move them there outright, but that no longer
works as we're no longer guaranteed to have a dbuf state when it comes
time to sanity check the ddb overlaps in skl_commit_modeset_enables().
I think when I wrote this originally we did the watermark/ddb
calculation last, and so we couldn't have any crtcs in the state w/o
also having the dbuf state. But that has since changed and we do the
watermark/ddb calculation much earlier, and thus it is now possible
to commit crtcs w/o a dbuf state. So we keep another copy of the
information in the crtc state.
v2: Rebase
v3: Duplicate the entries instead of moving
Reviewed-by: Stanislav Lisovskiy <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Generalize icl_get_first_dbuf_slice_offset() into something that
just gives us the start+end of the dbuf chunk covered by the
specified slices as a standard ddb entry. Initial idea was to use
it during readout as well, but we shall see.
Reviewed-by: Stanislav Lisovskiy <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Put the code into a function with a descriptive name. Also relocate
the code a bit help future work.
Reviewed-by: Stanislav Lisovskiy <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
skl_compute_dbuf_slices() has no use for the crtc state, so
just pass the crtc itself.
Reviewed-by: Stanislav Lisovskiy <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
skl_ddb_get_pipe_allocation_limits() doesn't care how the weights
for distributing the ddb are caclculated for each pipe. Put that
calculation into a separate function so that such mundane details
are hidden from view.
v2: s/adjusted_mode/pipe_mode/
Reviewed-by: Stanislav Lisovskiy <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
With vrr enabled the hardware no longer latches the registers
automagically at vblank start. The point at which it will do the
latching even when no push has been sent is the vmax decision
boundary. That is the thing we need to evade to avoid our
register latching to get split between two frames.
Signed-off-by: Ville Syrjälä <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Manasi Navare <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
To get sensible vblank timestamping behaviour we need to feed
the vmax based timings to the vblank code, otherwise it'll chop
off the scanline counter when it exceeds the minumum vtotal.
Additionally with VRR we have three cases to consider when we
generate the vblank timestamp:
1) we are in vertical active
-> nothing special needs to be done, just return the current
scanout position and the core will calculate the timestamp
corresponding to the past time when the current vertical
active started
2) we are in vertical blank and no push has been sent
-> the hardware will keep extending the vblank presumably
to its maximum length, so we make the timestmap match the
expected time when the max length vblank will end. Since
the timings used for this are now based on vmax nothing
special actually needs to be done
3) we are in vblank and a push has been sent so the vblank is
about to terminate
-> presumably we want the timestmap to accurately reflect
when the vblank will terminate, so we use the sampled
frame timestamp vs. current timestamp to guesstimate
how far along the vblank exit we are, and then we
adjust the reported scanout position accordingly so
that the core will see that the vblank is close to
ending.
v2:
* Fix the else if (use_scanline_Counter) (Manasi)
Signed-off-by: Manasi Navare <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Reviewed-by: Manasi Navare <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Dump vrr state alongside everything else.
Signed-off-by: Manasi Navare <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Reviewed-by: Manasi Navare <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
With VRR the earliest the registers can get latched are at
flipline decision boundary, calculate that as vrr_vmin_vblank_start()
and the latest the regsiters can get latched are vmax decision boundary
calculate that as vrr_vmax_vblank_start()
v2:
* Remove TODO and adjust extra scanline const (Manasi)
Signed-off-by: Manasi Navare <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Reviewed-by: Manasi Navare <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
This functions gets the VRR config from the VRR registers
to match the crtc state variables for VRR.
v2:
* Rebase (Manasi)
* Use HAS_VRR (Jani N)
v3:
* Get pipeline_full, flipline (Ville)
Cc: Jani Nikula <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
If VRR is enabled, the sink should ignore MSA parameters
and regenerate incoming video stream without depending
on these parameters. Hence set the MSA_TIMING_PAR_IGNORE_EN
bit if VRR is enabled.
Reset this bit on VRR disable.
v2:
* ACtually set the dpcd msa ignore bit (Ville)
Cc: Ville Syrjälä <[email protected]>
Cc: Jani Nikula <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
This patch disables the VRR enable and VRR PUSH
bits in the HW during commit modeset disable sequence.
Thsi disable will happen when the port is disabled
or when the userspace sets VRR prop to false and
requests to disable VRR.
v2:
* Use intel_de_rmw (Jani N)
v3:
* Remove rmw (Ville)
Cc: Ville Syrjälä <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
VRR achieves vblank stretching using the HW PUSH functionality.
So once the VRR is enabled during modeset then for each flip
request from userspace, in the atomic tail pipe_update_end()
we need to set the VRR push bit in HW for it to terminate
the vblank at configured flipline or anytime after flipline
or latest at the Vmax.
The HW clears the PUSH bit after the double buffer updates
are completed.
v2:
* Move send push to after irq en (Manasi)
* Call send push unconditionally (Jani N)
v3:
* Stall w.r.t Vrr vmax (Manasi, Gary Smith)
v4:
* Remove the rmw (Ville)
Cc: Ville Syrjälä <[email protected]>
Cc: Gary Smith <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
This patch computes the VRR parameters from VRR crtc states
and configures them in VRR registers during CRTC enable in
the modeset enable sequence.
v2:
* Remove initialization to 0 (Jani N)
* Use correct pipe %c (Jani N)
v3:
* Remove debug prints (Ville)
* Use cpu_trans instead of pipe for TRANS_VRR regs (Ville)
Cc: Ville Syrjälä <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Give the pipeline full line count bits more descriptive names
Signed-off-by: Ville Syrjälä <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Manasi Navare <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
If VRR is enabled, DRRS cannot be enabled, so make this check
in atomic check.
Signed-off-by: Manasi Navare <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Reviewed-by: Manasi Navare <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Even though our HW supports PSR + VRR, the available panels
do not work reliably with PSR and VRR together. So if user
requested VRR and is supported by HW enable that and do not
enable PSR in that case.
Cc: Ville Syrjälä <[email protected]>
Cc: Gwan-gyeong Mun <[email protected]>
Cc: Imre Deak <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Gwan-gyeong Mun <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
This forces a complete modeset if vrr drm crtc state goes
from enabled to disabled and vice versa.
This patch also computes vrr state variables from the mode timings
and based on the vrr property set by userspace as well as hardware's
vrr capability.
v2:
*Rebase
v3:
* Vmin = max (vtotal, vmin) (Manasi)
v4:
* set crtc_state->vrr.enable = 0 for disable request
v5:
* drm_dbg_kms, squash crtc states def patch (Jani N)
v6:
* Move vrr modeset check to separate function (Jani N)
v7:
* Ville's fixes - vmin, vmax rename, fix rounding dir
* Add pipeline full, flipline to crtc state
* Pass conn state to vrr_compute_config (Ville)
Cc: Ville Syrjälä <[email protected]>
Cc: Jani Nikula <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Extract intel_crtc_scanlines_since_frame_timestamp() from
__intel_get_crtc_scanline_from_timestamp(). We'll reuse this
for VRR vblank timestamps.
Signed-off-by: Ville Syrjälä <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Manasi Navare <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
We want to calculate the vblank_start for vblank evasion
differently for vrr. To make that nicer lets first extract
the current non-vrr case to a helper.
Signed-off-by: Ville Syrjälä <[email protected]>
Reviewed-by: Manasi Navare <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The vrr calculations will need to know the framestart delay value
we use. Currently we program it always to zero, but should that change
we probably want to stash it somewhere.
Could stick it into the crtc_state I suppose, but since we never
change it let's just stuff it into dev_priv for now.
v2:
* Rebase on drm-tip (Manasi)
v3:
* Framestart_delay as 1 - 4 to align with HW
Signed-off-by: Manasi Navare <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Reviewed-by: Manasi Navare <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
This function sets the VRR property for connector based
on the platform support, EDID monitor range and DP sink
DPCD capability of outputing video without msa
timing information.
v8:
* Use HAS_VRR, remove drm_conn declaration (Jani N)
* Fix typos in Comment (Jani N)
v7:
* Move the helper to separate file (Manasi)
v6:
* Remove unset of prop
v5:
* Fix the vrr prop not being set in kernel (Manasi)
* Unset the prop on connector disconnect (Manasi)
v4:
* Rebase (Mansi)
v3:
* intel_dp_is_vrr_capable can be used for debugfs, make it
non static (Manasi)
v2:
* Just set this in intel_dp_get_modes instead of new hook (Jani)
Cc: Ville Syrjälä <[email protected]>
Cc: Jani Nikula <[email protected]>
Signed-off-by: Aditya Swarup <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
We create a new file for all VRR related helpers.
Also add a function to check vrr capability based on
platform support, DPCD bits and EDID monitor range.
v2:
* Remove author (Jani N)
* Define HAS_VRR (Jani N)
* Ensure intel_dp can be obtained from conn (Jani N)
v3:
* Fix the header indent (Manasi)
Cc: Ville Syrjälä <[email protected]>
Cc: Jani Nikula <[email protected]>
Signed-off-by: Manasi Navare <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Render Decompression is supported with Y-Tiled main surface. The CCS is
linear and has 4 bits of data for each main surface cache line pair, a
ratio of 1:256. Additional Clear Color information is passed from the
user-space through an offset in the GEM BO. Add a new modifier to identify
and parse new Clear Color information and extend Gen12 render decompression
functionality to the newly added modifier.
v2: Fix has_alpha flag for modifiers, omit CC modifier during initial
plane config(Matt). Fix Lookup error.
v3: Fix the panic while running kms_cube
v4: Add alignment check and reuse the comments for ge12_ccs_formats(Matt)
v5: Fix typos and wrap comments(Matt)
v6:
- Use format block descriptors to get the subsampling calculations for
the CCS surface right.
- Use helpers to convert between main and CCS surfaces.
- Prevent coordinate checks for the CC surface.
- Simplify reading CC value from surface map, add description of CC val
layout.
- Remove redundant ccval variable from skl_program_plane().
v7:
- Move the CC value readout after syncing against any GPU write on the
FB obj (Nanley, Chris)
- Make sure the CC value readout works on platforms w/o struct pages
(dGFX) and other non-coherent platforms wrt. CPU reads (none atm).
(Chris)
v8:
- Rebase on the function param order change of
i915_gem_object_read_from_page().
- Clarify code comment on the clear color value format and the required
FB obj pinning/syncing by the caller.
- Remove redundant variables in
intel_atomic_prepare_plane_clear_colors().
v9:
- Fix s/sizeof(&ccval)/sizeof(ccval)/ typo.
Cc: Dhinakaran Pandiyan <[email protected]>
Cc: Ville Syrjala <[email protected]>
Cc: Shashank Sharma <[email protected]>
Cc: Rafael Antognolli <[email protected]>
Cc: Nanley G Chery <[email protected]>
Cc: Chris Wilson <[email protected]>
Reviewed-by: Matt Roper <[email protected]>
Signed-off-by: Radhakrishna Sripada <[email protected]>
Signed-off-by: Imre Deak <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Add a simple helper to read data with the CPU from the page of a GEM
object. Do the read either via a kmap if the object has struct pages
or an iomap otherwise. This is needed by the next patch, reading a u64
value from the object (w/o requiring the obj to be mapped to the GPU).
Suggested by Chris.
v2 (Chris):
- Sanitize the type and order of func params.
- Avoid consts requiring too many casts.
- Use BUG_ON instead of WARN_ON, simplify the conditions.
- Fix __iomem sparse errors.
- Leave locking/syncing/pinning up to the caller, require only that the
caller has pinned the object pages.
- Check for iomem backing store before reading via an iomap.
v3:
- Fix offset passed to io_mapping_map_wc() missing a mem.region.start
delta. (Chris, Matthew)
Cc: Chris Wilson <[email protected]>
Cc: Matthew Auld <[email protected]>
Signed-off-by: Imre Deak <[email protected]>
Reviewed-by: Chris Wilson <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Clear Color
Gen12 display can decompress surfaces compressed by render engine with
Clear Color, add a new modifier as the driver needs to know the surface
was compressed by render engine.
V2: Description changes as suggested by Rafael.
V3: Mention the Clear Color size of 64 bits in the comments(DK)
v4: Fix trailing whitespaces
v5: Explain Clear Color in the documentation.
v6: Documentation Nitpicks(Nanley)
Cc: Ville Syrjala <[email protected]>
Cc: Dhinakaran Pandiyan <[email protected]>
Cc: Kalyan Kondapally <[email protected]>
Cc: Rafael Antognolli <[email protected]>
Cc: Nanley Chery <[email protected]>
Signed-off-by: Radhakrishna Sripada <[email protected]>
Signed-off-by: Imre Deak <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Acked-by: Jani Nikula <[email protected]>
Acked-by: Nanley Chery <[email protected]>
Reviewed-by: Mika Kahola <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Move (num_hdcp_streams > 0) condition to stream_encryption()
code block, where it actually belongs.
This fixes the static analysis error of uninitialized symbol 'ret'.
v2:
- return 0 as the return value is already checked. [Ankit]
Cc: Ramalingam C <[email protected]>
Reported-by: kernel test robot <[email protected]>
Reported-by: Dan Carpenter <[email protected]>
Reviewed-by: Ankit Nautiyal <[email protected]>
Signed-off-by: Anshuman Gupta <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Initialize no. of streams transmitted on a port to zero
such that intel_hdcp_required_content_stream() can
prepared the content stream after subsequemt attmept to
enable hdcp after a HDCP failure.
v2:
- Initialize k at top level instead of else branch. [Jani]
Cc: Ramalingam C <[email protected]>
Signed-off-by: Anshuman Gupta <[email protected]>
Reviewed-by: Ankit Nautiyal <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
We haven't yet implemented support for backlights that need to be
enabled/disabled via PWM instead of AUX, which means we'll break things if
we enable DPCD backlight control on these machines. Luckily though since
most of these machines work fine just using the plain PWM backlight
controls anyway, there shouldn't be any issue with just leaving DPCD
backlight controls disabled in such situations.
This should fix the issues with PWM being left on that were being observed
on fi-bdw-samus.
Signed-off-by: Lyude Paul <[email protected]>
Reviewed-by: "Ville Syrjälä" <[email protected]>
Fixes: 4a8d79901d5b ("drm/i915/dp: Enable Intel's HDR backlight interface (only SDR for now)")
Testcase: igt/gem_exec_suspend/basic-s0 # fi-bdw-samus
Cc: Lyude Paul <[email protected]>
Cc: Jani Nikula <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Get rid of the "I like my random new style best" approach and unify
the handling for the DDI buf trans table sanity checks once again.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Imre Deak <[email protected]>
Reviewed-by: José Roberto de Souza <[email protected]>
|
|
The MH PHY vswing table does have all the entries these days. Get
rid of the old hacks in the code which claim otherwise.
This hack was totally bogus anyway. The correct way to handle the
lack of those two entries would have been to declare our max
vswing and pre-emph to both be level 2.
Cc: José Roberto de Souza <[email protected]>
Cc: Clinton Taylor <[email protected]>
Fixes: 9f7ffa297978 ("drm/i915/tc/icl: Update TC vswing tables")
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Imre Deak <[email protected]>
Reviewed-by: José Roberto de Souza <[email protected]>
|
|
Commit 7c553f8b5a7d ("drm/dp: Revert "drm/dp: Introduce EDID-based
quirks"") removed drm_dp_get_edid_quirks() and changed the signature of
drm_dp_has_quirk() while they were still being used in msm. Fix the
breakage. Functionally, removing the EDID-based quirks has no impact on
msm.
[The above commit was merged to drm-intel-next; make two wrongs a right
by merging this fix through drm-intel-next as well.]
Reported-by: Stephen Rothwell <[email protected]>
References: http://lore.kernel.org/r/[email protected]
Fixes: 7c553f8b5a7d ("drm/dp: Revert "drm/dp: Introduce EDID-based quirks"")
Cc: Lyude Paul <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Cc: Rob Clark <[email protected]>
Cc: Sean Paul <[email protected]>
Cc: [email protected]
Reviewed-by: Lyude Paul <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Split out the DP aux functionality to a new intel_dp_aux.[ch]. This is a
surprisingly clean cut.
v2:
- Remove intel_dp_pack_aux declaration from intel_dp.h (Anshuman)
- Fixed some whitespace/comment checkpatch warnings
Cc: Anshuman Gupta <[email protected]>
Reviewed-by: Rodrigo Vivi <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Add some namespacing to highlight what belongs where. No functional
changes.
Cc: Anshuman Gupta <[email protected]>
Reviewed-by: Rodrigo Vivi <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
intel_display.c has some pps functions that belong to intel_pps.c. Move
them over.
While at it, refactor the duplicate intel_pps_init() in intel_display.c
into an orthogonal intel_pps_setup() in intel_pps.c, and call it earlier
in intel_modeset_init_nogem().
Reviewed-by: Anshuman Gupta <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Once you realize there is no need to hold the pps mutex when calling
pps_init_timestamps() in intel_pps_init(), we can reuse
intel_pps_encoder_reset() which has the same code.
Since intel_dp_pps_init() is only called from one place now, move it
inline to remove one "init" function altogether.
Finally, remove some initialization from
vlv_initial_power_sequencer_setup() and do it in the caller to highlight
the similarity, not the difference, in the platforms.
v2: Fix comment (Anshuman)
Reviewed-by: Anshuman Gupta <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
This reverts commit 0883ce8146ed6074c76399f4e70dbed788582e12. Originally
these quirks were added because of the issues with using the eDP
backlight interfaces on certain laptop panels, which made it impossible
to properly probe for DPCD backlight support without having a whitelist
for panels that we know have working VESA backlight control interfaces
over DPCD. As well, it should be noted it was impossible to use the
normal sink OUI for recognizing these panels as none of them actually
filled out their OUIs, hence needing to resort to checking EDIDs.
At the time we weren't really sure why certain panels had issues with
DPCD backlight controls, but we eventually figured out that there was a
second interface that these problematic laptop panels actually did work
with and advertise properly: Intel's proprietary backlight interface for
HDR panels. So far the testing we've done hasn't brought any panels to
light that advertise this interface and don't support it properly, which
means we finally have a real solution to this problem.
As a result, we now have no need for the force DPCD backlight quirk, and
furthermore this also removes the need for any kind of EDID quirk
checking in DRM. So, let's just revert it for now since we were the only
driver using this.
v3:
* Rebase
v2:
* Fix indenting error picked up by checkpatch in
intel_edp_init_connector()
Signed-off-by: Lyude Paul <[email protected]>
Acked-by: Jani Nikula <[email protected]>
Cc: [email protected]
Cc: Vasily Khoruzhick <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Since we now support controlling panel backlights through DPCD using
both the standard VESA interface, and Intel's proprietary HDR backlight
interface, we should allow the user to be able to explicitly choose
between one or the other in the event that we're wrong about panels
reliably reporting support for the Intel HDR interface.
So, this commit adds support for this by introducing two new
enable_dpcd_backlight options: 2 which forces i915 to only probe for the
VESA interface, and 3 which forces i915 to only probe for the Intel
backlight interface (might be useful if we find panels in the wild that
report the VESA interface in their VBT, but actually only support the
Intel backlight interface).
v3:
* Rebase
Signed-off-by: Lyude Paul <[email protected]>
Reviewed-by: Jani Nikula <[email protected]>
Cc: [email protected]
Cc: Vasily Khoruzhick <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
So-recently a bunch of laptops on the market have started using DPCD
backlight controls instead of the traditional DDI backlight controls.
Originally we thought we had this handled by adding VESA backlight
control support to i915, but the story ended up being a lot more
complicated then that.
Simply put-there's two main backlight interfaces Intel can see in the
wild. Intel's proprietary HDR backlight interface, and the standard VESA
backlight interface. Note that many panels have been observed to report
support for both backlight interfaces, but testing has shown far more
panels work with the Intel HDR backlight interface at the moment.
Additionally, the VBT appears to be capable of reporting support for the
VESA backlight interface but not the Intel HDR interface which needs to
be probed by setting the right magic OUI.
On top of that however, there's also actually two different variants of
the Intel HDR backlight interface. The first uses the AUX channel for
controlling the brightness of the screen in both SDR and HDR mode, and
the second only uses the AUX channel for setting the brightness level in
HDR mode - relying on PWM for setting the brightness level in SDR mode.
For the time being we've been using EDIDs to maintain a list of quirks
for panels that safely do support the VESA backlight interface. Adding
support for Intel's HDR backlight interface in addition however, should
finally allow us to auto-detect eDP backlight controls properly so long
as we probe like so:
* If the panel's VBT reports VESA backlight support, assume it really
does support it
* If the panel's VBT reports DDI backlight controls:
* First probe for Intel's HDR backlight interface
* If that fails, probe for VESA's backlight interface
* If that fails, assume no DPCD backlight control
* If the panel's VBT reports any other backlight type: just assume it
doesn't have DPCD backlight controls
Changes since v4:
* Fix checkpatch issues
Changes since v3:
* Stop using drm_device and use drm_i915_private instead
* Don't forget to return from intel_dp_aux_hdr_get_backlight() if we fail
to read the current backlight mode from the DPCD
* s/uint8_t/u8/
* Remove unneeded parenthesis in intel_dp_aux_hdr_enable_backlight()
* Use drm_dbg_kms() in intel_dp_aux_init_backlight_funcs()
Signed-off-by: Lyude Paul <[email protected]>
Reviewed-by: Jani Nikula <[email protected]>
Cc: [email protected]
Cc: Vasily Khoruzhick <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|