Age | Commit message (Collapse) | Author | Files | Lines |
|
Fix offset computation in __sev_dbg_decrypt() to include the
source paddr before it is rounded down to be aligned to 16 bytes
as required by SEV API. This fixes incorrect guest memory dumps
observed when using qemu monitor.
Signed-off-by: Ashish Kalra <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
If we have more than 4 displays we will run
into dummy irq calls or flip timout issues.
Reviewed-by: Nicholas Kazlauskas <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
From commit 6915564dc5a8 ("ACPI: OSL: Change the type of
acpi_os_map_generic_address() return value"),
acpi_os_map_generic_address() will return logical address or NULL
for error, but for ACPI_ADR_SPACE_SYSTEM_IO case, it should be also
return 0 as it's a normal case, but now it will return -ENXIO.
So check it out for such case to avoid einj module initialization
fail.
Fixes: 6915564dc5a8 ("ACPI: OSL: Change the type of acpi_os_map_generic_address() return value")
Cc: <[email protected]>
Reviewed-by: James Morse <[email protected]>
Tested-by: Tony Luck <[email protected]>
Signed-off-by: Aili Yao <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Martin Schiller is an active developer and reviewer for the X.25 code.
His company is providing products based on the Linux X.25 stack.
So he is a good candidate for maintainers of the X.25 code.
The original maintainer of the X.25 network layer (Andrew Hendry) has
not sent any email to the netdev mail list since 2013. So he is probably
inactive now.
Cc: Andrew Hendry <[email protected]>
Signed-off-by: Xie He <[email protected]>
Acked-by: Martin Schiller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master
KVM: s390: Fixes for 5.10
- do not reset the global diag318 data for per-cpu reset
- do not mark memory as protected too early
|
|
Packets are processed even though the first fragment don't include all
headers through the upper layer header. This breaks TAHI IPv6 Core
Conformance Test v6LC.1.3.6.
Referring to RFC8200 SECTION 4.5: "If the first fragment does not include
all headers through an Upper-Layer header, then that fragment should be
discarded and an ICMP Parameter Problem, Code 3, message should be sent to
the source of the fragment, with the Pointer field set to zero."
The fragment needs to be validated the same way it is done in
commit 2efdaaaf883a ("IPv6: reply ICMP error if the first fragment don't
include all headers") for ipv6. Wrap the validation into a common function,
ipv6_frag_thdr_truncated() to check for truncation in the upper layer
header. This validation does not fullfill all aspects of RFC 8200,
section 4.5, but is at the moment sufficient to pass mentioned TAHI test.
In netfilter, utilize the fragment offset returned by find_prev_fhdr() to
let ipv6_frag_thdr_truncated() start it's traverse from the fragment
header.
Return 0 to drop the fragment in the netfilter. This is the same behaviour
as used on other protocol errors in this function, e.g. when
nf_ct_frag6_queue() returns -EPROTO. The Fragment will later be picked up
by ipv6_frag_rcv() in reassembly.c. ipv6_frag_rcv() will then send an
appropriate ICMP Parameter Problem message back to the source.
References commit 2efdaaaf883a ("IPv6: reply ICMP error if the first
fragment don't include all headers")
Signed-off-by: Georg Kohmann <[email protected]>
Acked-by: Pablo Neira Ayuso <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
After initial kernel module load during kernel boot and removing
the module and try to load it again an Unable to handle kernel
paging request is observed:
Unable to handle kernel paging request at virtual address ffffa44f7416eae0
Mem abort info:
ESR = 0x96000047
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000047
CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp=000000008147c000
[ffffa44f7416eae0] pgd=000000017df9f003, p4d=000000017df9f003,
pud=000000017df9e003, pmd=000000017df9b003, pte=0000000000000000
Internal error: Oops: 96000047 [#1] PREEMPT SMP
Modules linked in: venus_core(+) snd_soc_wsa881x regmap_sdw af_alg
snd_soc_wcd934x soundwire_qcom gpio_wcd934x q6asm_dai q6routing
q6adm q6afe_dai snd_soc_hdmi_codec q6afe q6asm q6dsp_common q6cor
display_connector rmtfs_mem drm ip_tables x_tables ipv6
[last unloaded: venus_core]
CPU: 6 PID: 889 Comm: modprobe Tainted: G W 5.10.0-rc1+ #8
Hardware name: Thundercomm Dragonboard 845c (DT)
pstate: 80400085 (Nzcv daIf +PAN -UAO -TCO BTYPE=--)
pc : queued_spin_lock_slowpath+0x1dc/0x3c8
lr : do_raw_spin_lock+0xc0/0x118
sp : ffff8000142cb7b0
x29: ffff8000142cb7b0 x28: 0000000000000013
x27: ffffa44f72de5690 x26: 0000000000000003
x25: ffff17c2d00f8080 x24: ffff17c2c0d78010
x23: ffff17c2c0d4f700 x22: ffff17c2d00f8080
x21: 0000000000000000 x20: ffffa44f74148000
x19: ffff17c2c0d4f8f8 x18: 0000000000000000
x17: 0000000000000000 x16: ffffa44f7342f158
x15: 0000000000000040 x14: ffffa44f746e8320
x13: 0000000000000228 x12: 0000000000000020
x11: 0000000000000000 x10: 00000000001c0000
x9 : 0000000000000000 x8 : ffff17c33d746ac0
x7 : ffff17c2c109b000 x6 : ffffa44f7416eac0
x5 : ffff17c33d746ac0 x4 : 0000000000000000
x3 : ffff17c2c0d4f8f8 x2 : ffffa44f7416eae0
x1 : ffffa44f7416eae0 x0 : ffff17c33d746ac8
Call trace:
queued_spin_lock_slowpath+0x1dc/0x3c8
do_raw_spin_lock+0xc0/0x118
_raw_spin_lock_irqsave+0x80/0x14c
__pm_runtime_resume+0x38/0xb8
device_link_add+0x3b8/0x5d0
core_get_v4+0x268/0x2d8 [venus_core]
venus_probe+0x108/0x458 [venus_core]
platform_drv_probe+0x54/0xa8
really_probe+0xe4/0x3b0
driver_probe_device+0x58/0xb8
device_driver_attach+0x74/0x80
__driver_attach+0x58/0xe8
bus_for_each_dev+0x70/0xc0
driver_attach+0x24/0x30
bus_add_driver+0x150/0x1f8
driver_register+0x64/0x120
__platform_driver_register+0x48/0x58
qcom_venus_driver_init+0x20/0x1000 [venus_core]
do_one_initcall+0x84/0x458
do_init_module+0x58/0x208
load_module+0x1ec0/0x26a8
__do_sys_finit_module+0xb8/0xf8
__arm64_sys_finit_module+0x20/0x30
el0_svc_common.constprop.0+0x7c/0x1c0
do_el0_svc+0x24/0x90
el0_sync_handler+0x180/0x188
el0_sync+0x174/0x180
Code: 91002100 8b0200c2 f861d884 aa0203e1 (f8246828)
---[ end trace f1f687c15fd6b2ca ]---
note: modprobe[889] exited with preempt_count 1
After revisit the OPP part of the code I found that OPP pmdomain
is detached with direct call to dev_pm_domain_detach instead of
OPP wraper for detaching pmdomains with OPP table. Correct this
by calling the OPP dev_pm_opp_detach_genpd.
Fixes: 9a538b83612c ('media: venus: core: Add support for opp tables/perf voting')
Signed-off-by: Stanimir Varbanov <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
|
|
The profile and level in op_set_ctrl was recently changed but during
v4l2_ctrl_handler_setup profile and level control values are mangled.
Fixes: 435c53c3698f ("media: venus: venc: Use helper to set profile and level")
Signed-off-by: Stanimir Varbanov <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
|
|
Zhang Qilong says:
====================
Fix usage counter leak by adding a general sync ops
In many case, we need to check return value of pm_runtime_get_sync,
but it brings a trouble to the usage counter processing. Many callers
forget to decrease the usage counter when it failed, which could
resulted in reference leak. It has been discussed a lot[0][1]. So we
add a function to deal with the usage counter for better coding and
view. Then, we replace pm_runtime_resume_and_get with it in fec_main.c
to avoid it.
[0] https://lkml.org/lkml/2020/6/14/88
[1] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
pm_runtime_get_sync() will increment pm usage at first and it will
resume the device later. If runtime of the device has error or
device is in inaccessible state(or other error state), resume
operation will fail. If we do not call put operation to decrease
the reference, it will result in reference count leak. Moreover,
this device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by replacing it with
pm_runtime_resume_and_get.
Fixes: 8fff755e9f8d0 ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Zhang Qilong <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In many case, we need to check return value of pm_runtime_get_sync, but
it brings a trouble to the usage counter processing. Many callers forget
to decrease the usage counter when it failed, which could resulted in
reference leak. It has been discussed a lot[0][1]. So we add a function
to deal with the usage counter for better coding.
[0]https://lkml.org/lkml/2020/6/14/88
[1]https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139
Signed-off-by: Zhang Qilong <[email protected]>
Acked-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Actually, burst size is equal to '1 << desc->rqcfg.brst_size'.
we should use burst size, not desc->rqcfg.brst_size.
dma memcpy performance on Rockchip RV1126
@ 1512MHz A7, 1056MHz LPDDR3, 200MHz DMA:
dmatest:
/# echo dma0chan0 > /sys/module/dmatest/parameters/channel
/# echo 4194304 > /sys/module/dmatest/parameters/test_buf_size
/# echo 8 > /sys/module/dmatest/parameters/iterations
/# echo y > /sys/module/dmatest/parameters/norandom
/# echo y > /sys/module/dmatest/parameters/verbose
/# echo 1 > /sys/module/dmatest/parameters/run
dmatest: dma0chan0-copy0: result #1: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #2: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #3: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #4: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #5: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #6: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #7: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #8: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
Before:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 48 iops 200338 KB/s (0)
After this patch:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 179 iops 734873 KB/s (0)
After this patch and increase dma clk to 400MHz:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 259 iops 1062929 KB/s (0)
Signed-off-by: Sugar Zhang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Commit 7f832645d0e5 ("dmaengine: ioatdma: remove ioatdma v2 registration")
missed to remove dca2_tag_map_valid() during its removal. Hence, since
then, dca2_tag_map_valid() is unused and make CC=clang W=1 warns:
drivers/dma/ioat/dca.c:44:19:
warning: unused function 'dca2_tag_map_valid' [-Wunused-function]
So, remove this unused function and get rid of a -Wused-function warning.
Signed-off-by: Lukas Bulwahn <[email protected]>
Reviewed-by: Nathan Chancellor <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
This fix is for a failure that occurred in the DWARF unwind perf test.
Stack unwinders may probe memory when looking for frames.
Memory sanitizer will poison and track uninitialized memory on the
stack, and on the heap if the value is copied to the heap.
This can lead to false memory sanitizer failures for the use of an
uninitialized value.
Avoid this problem by removing the poison on the copied stack.
The full msan failure with track origins looks like:
==2168==WARNING: MemorySanitizer: use-of-uninitialized-value
#0 0x559ceb10755b in handle_cfi elfutils/libdwfl/frame_unwind.c:648:8
#1 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4
#2 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7
#3 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10
#4 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17
#5 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17
#6 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14
#7 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10
#8 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8
#9 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8
#10 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26
#11 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0)
#12 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2
#13 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9
#14 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9
#15 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8
#16 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9
#17 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9
#18 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4
#19 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9
#20 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11
#21 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8
#22 0x559cea95fbce in run_argv tools/perf/perf.c:409:2
#23 0x559cea95fbce in main tools/perf/perf.c:539:3
Uninitialized value was stored to memory at
#0 0x559ceb106acf in __libdwfl_frame_reg_set elfutils/libdwfl/frame_unwind.c:77:22
#1 0x559ceb106acf in handle_cfi elfutils/libdwfl/frame_unwind.c:627:13
#2 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4
#3 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7
#4 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10
#5 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17
#6 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17
#7 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14
#8 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10
#9 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8
#10 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8
#11 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26
#12 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0)
#13 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2
#14 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9
#15 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9
#16 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8
#17 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9
#18 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9
#19 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4
#20 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9
#21 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11
#22 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8
#23 0x559cea95fbce in run_argv tools/perf/perf.c:409:2
#24 0x559cea95fbce in main tools/perf/perf.c:539:3
Uninitialized value was stored to memory at
#0 0x559ceb106a54 in handle_cfi elfutils/libdwfl/frame_unwind.c:613:9
#1 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4
#2 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7
#3 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10
#4 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17
#5 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17
#6 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14
#7 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10
#8 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8
#9 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8
#10 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26
#11 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0)
#12 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2
#13 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9
#14 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9
#15 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8
#16 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9
#17 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9
#18 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4
#19 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9
#20 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11
#21 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8
#22 0x559cea95fbce in run_argv tools/perf/perf.c:409:2
#23 0x559cea95fbce in main tools/perf/perf.c:539:3
Uninitialized value was stored to memory at
#0 0x559ceaff8800 in memory_read tools/perf/util/unwind-libdw.c:156:10
#1 0x559ceb10f053 in expr_eval elfutils/libdwfl/frame_unwind.c:501:13
#2 0x559ceb1060cc in handle_cfi elfutils/libdwfl/frame_unwind.c:603:18
#3 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4
#4 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7
#5 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10
#6 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17
#7 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17
#8 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14
#9 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10
#10 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8
#11 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8
#12 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26
#13 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0)
#14 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2
#15 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9
#16 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9
#17 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8
#18 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9
#19 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9
#20 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4
#21 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9
#22 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11
#23 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8
#24 0x559cea95fbce in run_argv tools/perf/perf.c:409:2
#25 0x559cea95fbce in main tools/perf/perf.c:539:3
Uninitialized value was stored to memory at
#0 0x559cea9027d9 in __msan_memcpy llvm/llvm-project/compiler-rt/lib/msan/msan_interceptors.cpp:1558:3
#1 0x559cea9d2185 in sample_ustack tools/perf/arch/x86/tests/dwarf-unwind.c:41:2
#2 0x559cea9d202c in test__arch_unwind_sample tools/perf/arch/x86/tests/dwarf-unwind.c:72:9
#3 0x559ceabc9cbd in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:106:6
#4 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26
#5 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0)
#6 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2
#7 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9
#8 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9
#9 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8
#10 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9
#11 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9
#12 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4
#13 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9
#14 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11
#15 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8
#16 0x559cea95fbce in run_argv tools/perf/perf.c:409:2
#17 0x559cea95fbce in main tools/perf/perf.c:539:3
Uninitialized value was created by an allocation of 'bf' in the stack frame of function 'perf_event__synthesize_mmap_events'
#0 0x559ceafc5f60 in perf_event__synthesize_mmap_events tools/perf/util/synthetic-events.c:445
SUMMARY: MemorySanitizer: use-of-uninitialized-value elfutils/libdwfl/frame_unwind.c:648:8 in handle_cfi
Signed-off-by: Ian Rogers <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: [email protected]
Cc: Jiri Olsa <[email protected]>
Cc: Mark Rutland <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Sandeep Dasgupta <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lore.kernel.org/lkml/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Portal size is 4k. Current code is mapping all 4 portals in a single chunk.
Restrict the mapped portal size to a single portal to ensure that submission
only goes to the intended portal address.
Fixes: c52ca478233c ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Dave Jiang <[email protected]>
Link: https://lore.kernel.org/r/160513342642.510187.16450549281618747065.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <[email protected]>
|
|
"perf inject" can create corrupt files when synthesizing sample events from AUX
data. This happens when in the input file, the first event (for the AUX data)
has a different sample_type from the second event (generally dummy).
Specifically, they differ in the bits that indicate the standard fields
appended to perf records in the mmap buffer. "perf inject" deletes the first
event and moves up the second event to first position.
The problem is with the synthetic PERF_RECORD_MMAP (etc.) events created
by "perf record".
Since these are synthetic versions of events which are normally produced
by the kernel, they have to have the standard fields appended as
described by sample_type.
"perf record" fills these in with zeroes, including the IDENTIFIER
field; perf readers interpret records with zero IDENTIFIER using the
descriptor for the first event in the file.
Since "perf inject" changes the first event, these synthetic records are
then processed with the wrong value of sample_type, and the perf reader
reads bad data, reports on incorrect length records etc.
Mismatching sample_types are seen with "perf record -e cs_etm//", where the AUX
event has TID|TIME|CPU|IDENTIFIER and the dummy event has TID|TIME|IDENTIFIER.
Perhaps they could be the same, but it isn't normally a problem if they aren't
- perf has no problems reading the file.
The sample_types have to agree on the position of IDENTIFIER, because
that's how perf finds the right event descriptor in the first place, but
they don't normally have to agree on other fields, and perf doesn't
check that they do.
The problem is specific to the way "perf inject" reorganizes the events
and the way synthetic MMAP events are recorded with a zero identifier. A
simple solution is to stop "perf inject" deleting the tracing event.
Committer testing
Removed the now unused 'evsel' variable, update the comment about the
evsel removal not being performed anymore, and apply the patch manually
as it failed with this warning:
warning: Patch sent with format=flowed; space at the end of lines might be lost.
Testing it with:
$ perf bench internals inject-build-id
# Running 'internals/inject-build-id' benchmark:
Average build-id injection took: 8.543 msec (+- 0.130 msec)
Average time per event: 0.838 usec (+- 0.013 usec)
Average memory usage: 12717 KB (+- 9 KB)
Average build-id-all injection took: 5.710 msec (+- 0.058 msec)
Average time per event: 0.560 usec (+- 0.006 usec)
Average memory usage: 12079 KB (+- 7 KB)
$
Signed-off-by: Al Grant <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Acked-by: Namhyung Kim <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Mark Rutland <[email protected]>
Cc: Peter Zijlstra <[email protected]>
LPU-Reference: [email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, round 4:
- Fix MDIO over clocking on vf610-zii-dev-rev-b board to get switch
device work reliably.
- Fix imx50-evk IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
- Fix voltage for 1.6GHz CPU operating point on i.MX8MM to match
hardware datasheet.
- Fix phy-mode for KSZ9031 PHY on imx6qdl-udoo board.
* tag 'imx-fixes-5.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
Link: https://lore.kernel.org/r/20201116090702.GM5849@dragon
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.10
- Add missing audio clock on RZ/G2H.
* tag 'renesas-fixes-for-v5.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a774e1: Add missing audio_clk_b
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Stefan Agner reported a bug when using zsram on 32-bit Arm machines
with RAM above the 4GB address boundary:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = a27bd01c
[00000000] *pgd=236a0003, *pmd=1ffa64003
Internal error: Oops: 207 [#1] SMP ARM
Modules linked in: mdio_bcm_unimac(+) brcmfmac cfg80211 brcmutil raspberrypi_hwmon hci_uart crc32_arm_ce bcm2711_thermal phy_generic genet
CPU: 0 PID: 123 Comm: mkfs.ext4 Not tainted 5.9.6 #1
Hardware name: BCM2711
PC is at zs_map_object+0x94/0x338
LR is at zram_bvec_rw.constprop.0+0x330/0xa64
pc : [<c0602b38>] lr : [<c0bda6a0>] psr: 60000013
sp : e376bbe0 ip : 00000000 fp : c1e2921c
r10: 00000002 r9 : c1dda730 r8 : 00000000
r7 : e8ff7a00 r6 : 00000000 r5 : 02f9ffa0 r4 : e3710000
r3 : 000fdffe r2 : c1e0ce80 r1 : ebf979a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 30c5383d Table: 235c2a80 DAC: fffffffd
Process mkfs.ext4 (pid: 123, stack limit = 0x495a22e6)
Stack: (0xe376bbe0 to 0xe376c000)
As it turns out, zsram needs to know the maximum memory size, which
is defined in MAX_PHYSMEM_BITS when CONFIG_SPARSEMEM is set, or in
MAX_POSSIBLE_PHYSMEM_BITS on the x86 architecture.
The same problem will be hit on all 32-bit architectures that have a
physical address space larger than 4GB and happen to not enable sparsemem
and include asm/sparsemem.h from asm/pgtable.h.
After the initial discussion, I suggested just always defining
MAX_POSSIBLE_PHYSMEM_BITS whenever CONFIG_PHYS_ADDR_T_64BIT is
set, or provoking a build error otherwise. This addresses all
configurations that can currently have this runtime bug, but
leaves all other configurations unchanged.
I looked up the possible number of bits in source code and
datasheets, here is what I found:
- on ARC, CONFIG_ARC_HAS_PAE40 controls whether 32 or 40 bits are used
- on ARM, CONFIG_LPAE enables 40 bit addressing, without it we never
support more than 32 bits, even though supersections in theory allow
up to 40 bits as well.
- on MIPS, some MIPS32r1 or later chips support 36 bits, and MIPS32r5
XPA supports up to 60 bits in theory, but 40 bits are more than
anyone will ever ship
- On PowerPC, there are three different implementations of 36 bit
addressing, but 32-bit is used without CONFIG_PTE_64BIT
- On RISC-V, the normal page table format can support 34 bit
addressing. There is no highmem support on RISC-V, so anything
above 2GB is unused, but it might be useful to eventually support
CONFIG_ZRAM for high pages.
Fixes: 61989a80fb3a ("staging: zsmalloc: zsmalloc memory allocation library")
Fixes: 02390b87a945 ("mm/zsmalloc: Prepare to variable MAX_PHYSMEM_BITS")
Acked-by: Thomas Bogendoerfer <[email protected]>
Reviewed-by: Stefan Agner <[email protected]>
Tested-by: Stefan Agner <[email protected]>
Acked-by: Mike Rapoport <[email protected]>
Link: https://lore.kernel.org/linux-mm/bdfa44bf1c570b05d6c70898e2bbb0acf234ecdf.1604762181.git.stefan@agner.ch/
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2020-11-15
Anant Thazhemadam contributed two patches for the AF_CAN that prevent potential
access of uninitialized member in can_rcv() and canfd_rcv().
The next patch is by Alejandro Concepcion Rodriguez and changes can_restart()
to use the correct function to push a skb into the networking stack from
process context.
Zhang Qilong's patch fixes a memory leak in the error path of the ti_hecc's
probe function.
A patch by me fixes mcba_usb_start_xmit() function in the mcba_usb driver, to
first fill the skb and then pass it to can_put_echo_skb().
Colin Ian King's patch fixes a potential integer overflow on shift in the
peak_usb driver.
The next two patches target the flexcan driver, a patch by me adds the missing
"req_bit" to the stop mode property comment (which was broken during net-next
for v5.10). Zhang Qilong's patch fixes the failure handling of
pm_runtime_get_sync().
The next seven patches target the m_can driver including the tcan4x5x spi
driver glue code. Enric Balletbo i Serra's patch for the tcan4x5x Kconfig fix
the REGMAP_SPI dependency handling. A patch by me for the tcan4x5x driver's
probe() function adds missing error handling to for devm_regmap_init(), and in
tcan4x5x_can_remove() the order of deregistration is fixed. Wu Bo's patch for
the m_can driver fixes the state change handling in
m_can_handle_state_change(). Two patches by Dan Murphy first introduce
m_can_class_free_dev() and then make use of it to fix the freeing of the can
device. A patch by Faiz Abbas add a missing shutdown of the CAN controller in
the m_can_stop() function.
* tag 'linux-can-fixes-for-5.10-20201115' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: m_can_stop(): set device to software init mode before closing
can: m_can: Fix freeing of can device from peripherials
can: m_can: m_can_class_free_dev(): introduce new function
can: m_can: m_can_handle_state_change(): fix state change
can: tcan4x5x: tcan4x5x_can_remove(): fix order of deregistration
can: tcan4x5x: tcan4x5x_can_probe(): add missing error checking for devm_regmap_init()
can: tcan4x5x: replace depends on REGMAP_SPI with depends on SPI
can: flexcan: fix failure handling of pm_runtime_get_sync()
can: flexcan: flexcan_setup_stop_mode(): add missing "req_bit" to stop mode property comment
can: peak_usb: fix potential integer overflow on shift of a int
can: mcba_usb: mcba_usb_start_xmit(): first fill skb, then pass to can_put_echo_skb()
can: ti_hecc: Fix memleak in ti_hecc_probe
can: dev: can_restart(): post buffer from the right context
can: af_can: prevent potential access of uninitialized member in canfd_rcv()
can: af_can: prevent potential access of uninitialized member in can_rcv()
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
When requeueing all requests on the device request queue to the blocklayer
we might get to an ERP (error recovery) request that is a copy of an
original CQR.
Those requests do not have blocklayer request information or a pointer to
the dasd_queue set. When trying to access those data it will lead to a
null pointer dereference in dasd_requeue_all_requests().
Fix by checking if the request is an ERP request that can simply be
ignored. The blocklayer request will be requeued by the original CQR that
is on the device queue right behind the ERP request.
Fixes: 9487cfd3430d ("s390/dasd: fix handling of internal requests")
Cc: <[email protected]> #4.16
Signed-off-by: Stefan Haberland <[email protected]>
Reviewed-by: Jan Hoeppner <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Add HD Audio PCI ID and HDMI codec vendor ID for Intel Alder Lake.
Signed-off-by: Kai Vehmanen <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The following warning is reported if lock debugging is enabled.
DEBUG_LOCKS_WARN_ON(1)
WARNING: CPU: 1 PID: 1 at kernel/locking/lockdep.c:4617 lockdep_init_map_waits+0x141/0x222
...
Call Trace:
__kernfs_create_file+0x7a/0xd8
sysfs_add_file_mode_ns+0x135/0x189
sysfs_create_file_ns+0x70/0xa0
acpi_fan_probe+0x547/0x621
platform_drv_probe+0x67/0x8b
...
Dynamically allocated sysfs attributes need to be initialized to avoid
the warning.
Fixes: d19e470b6605 ("ACPI: fan: Expose fan performance state information")
Signed-off-by: Guenter Roeck <[email protected]>
Cc: 5.6+ <[email protected]> # 5.6+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
pci_dev::physfn is only available when CONFIG_PCI_ATS is set. The recent
fix for the irqdomain rework missed that dependency which makes the build
fail when CONFIG_PCI_ATS=n.
Add the necessary #ifdeffery.
Reported-by: Geert Uytterhoeven <[email protected]>
Fixes: ff828729be44 ("iommu/vt-d: Cure VF irqdomain hickup")
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Joerg Roedel <[email protected]>
|
|
When accessing the ESB page of a source interrupt, the fault handler
will retrieve the page address from the XIVE interrupt 'xive_irq_data'
structure. If the associated KVM XIVE interrupt is not valid, that is
not allocated at the HW level for some reason, the fault handler will
dereference a NULL pointer leading to the oops below :
WARNING: CPU: 40 PID: 59101 at arch/powerpc/kvm/book3s_xive_native.c:259 xive_native_esb_fault+0xe4/0x240 [kvm]
CPU: 40 PID: 59101 Comm: qemu-system-ppc Kdump: loaded Tainted: G W --------- - - 4.18.0-240.el8.ppc64le #1
NIP: c00800000e949fac LR: c00000000044b164 CTR: c00800000e949ec8
REGS: c000001f69617840 TRAP: 0700 Tainted: G W --------- - - (4.18.0-240.el8.ppc64le)
MSR: 9000000000029033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 44044282 XER: 00000000
CFAR: c00000000044b160 IRQMASK: 0
GPR00: c00000000044b164 c000001f69617ac0 c00800000e96e000 c000001f69617c10
GPR04: 05faa2b21e000080 0000000000000000 0000000000000005 ffffffffffffffff
GPR08: 0000000000000000 0000000000000001 0000000000000000 0000000000000001
GPR12: c00800000e949ec8 c000001ffffd3400 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 c000001f5c065160 c000000001c76f90
GPR24: c000001f06f20000 c000001f5c065100 0000000000000008 c000001f0eb98c78
GPR28: c000001dcab40000 c000001dcab403d8 c000001f69617c10 0000000000000011
NIP [c00800000e949fac] xive_native_esb_fault+0xe4/0x240 [kvm]
LR [c00000000044b164] __do_fault+0x64/0x220
Call Trace:
[c000001f69617ac0] [0000000137a5dc20] 0x137a5dc20 (unreliable)
[c000001f69617b50] [c00000000044b164] __do_fault+0x64/0x220
[c000001f69617b90] [c000000000453838] do_fault+0x218/0x930
[c000001f69617bf0] [c000000000456f50] __handle_mm_fault+0x350/0xdf0
[c000001f69617cd0] [c000000000457b1c] handle_mm_fault+0x12c/0x310
[c000001f69617d10] [c00000000007ef44] __do_page_fault+0x264/0xbb0
[c000001f69617df0] [c00000000007f8c8] do_page_fault+0x38/0xd0
[c000001f69617e30] [c00000000000a714] handle_page_fault+0x18/0x38
Instruction dump:
40c2fff0 7c2004ac 2fa90000 409e0118 73e90001 41820080 e8bd0008 7c2004ac
7ca90074 39400000 915c0000 7929d182 <0b090000> 2fa50000 419e0080 e89e0018
---[ end trace 66c6ff034c53f64f ]---
xive-kvm: xive_native_esb_fault: accessing invalid ESB page for source 8 !
Fix that by checking the validity of the KVM XIVE interrupt structure.
Fixes: 6520ca64cde7 ("KVM: PPC: Book3S HV: XIVE: Add a mapping for the source ESB pages")
Cc: [email protected] # v5.2+
Reported-by: Greg Kurz <[email protected]>
Signed-off-by: Cédric Le Goater <[email protected]>
Tested-by: Greg Kurz <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Annotate tegra_pm_set[clear]_cpu_in_lp2() with RCU_NONIDLE in order to
fix lockdep warning about suspicious RCU usage of a spinlock during late
idling phase.
WARNING: suspicious RCU usage
...
include/trace/events/lock.h:13 suspicious rcu_dereference_check() usage!
...
(dump_stack) from (lock_acquire)
(lock_acquire) from (_raw_spin_lock)
(_raw_spin_lock) from (tegra_pm_set_cpu_in_lp2)
(tegra_pm_set_cpu_in_lp2) from (tegra_cpuidle_enter)
(tegra_cpuidle_enter) from (cpuidle_enter_state)
(cpuidle_enter_state) from (cpuidle_enter_state_coupled)
(cpuidle_enter_state_coupled) from (cpuidle_enter)
(cpuidle_enter) from (do_idle)
...
Tested-by: Peter Geis <[email protected]>
Reported-by: Peter Geis <[email protected]>
Signed-off-by: Dmitry Osipenko <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Although cache alias management calls set up and tear down TLB entries
and fast_second_level_miss is able to restore TLB entry should it be
evicted they absolutely cannot preempt each other because they use the
same TLBTEMP area for different purposes.
Disable preemption around all cache alias management calls to enforce
that.
Cc: [email protected]
Signed-off-by: Max Filippov <[email protected]>
|
|
fast_second_level_miss handler for the TLBTEMP area has an assumption
that page table directory entry for the TLBTEMP address range is 0. For
it to be true the TLBTEMP area must be aligned to 4MB boundary and not
share its 4MB region with anything that may use a page table. This is
not true currently: TLBTEMP shares space with vmalloc space which
results in the following kinds of runtime errors when
fast_second_level_miss loads page table directory entry for the vmalloc
space instead of fixing up the TLBTEMP area:
Unable to handle kernel paging request at virtual address c7ff0e00
pc = d0009275, ra = 90009478
Oops: sig: 9 [#1] PREEMPT
CPU: 1 PID: 61 Comm: kworker/u9:2 Not tainted 5.10.0-rc3-next-20201110-00007-g1fe4962fa983-dirty #58
Workqueue: xprtiod xs_stream_data_receive_workfn
a00: 90009478 d11e1dc0 c7ff0e00 00000020 c7ff0000 00000001 7f8b8107 00000000
a08: 900c5992 d11e1d90 d0cc88b8 5506e97c 00000000 5506e97c d06c8074 d11e1d90
pc: d0009275, ps: 00060310, depc: 00000014, excvaddr: c7ff0e00
lbeg: d0009275, lend: d0009287 lcount: 00000003, sar: 00000010
Call Trace:
xs_stream_data_receive_workfn+0x43c/0x770
process_one_work+0x1a1/0x324
worker_thread+0x1cc/0x3c0
kthread+0x10d/0x124
ret_from_kernel_thread+0xc/0x18
Cc: [email protected]
Signed-off-by: Max Filippov <[email protected]>
|
|
The nVHE percpu data is partially linked but the nVHE linker script did
not align the percpu section. The PERCPU_INPUT macro would then align
the data to a page boundary:
#define PERCPU_INPUT(cacheline) \
__per_cpu_start = .; \
*(.data..percpu..first) \
. = ALIGN(PAGE_SIZE); \
*(.data..percpu..page_aligned) \
. = ALIGN(cacheline); \
*(.data..percpu..read_mostly) \
. = ALIGN(cacheline); \
*(.data..percpu) \
*(.data..percpu..shared_aligned) \
PERCPU_DECRYPTED_SECTION \
__per_cpu_end = .;
but then when the final vmlinux linking happens the hypervisor percpu
data is included after page alignment and so the offsets potentially
don't match. On my build I saw that the .hyp.data..percpu section was
at address 0x20 and then the percpu data would begin at 0x1000 (because
of the page alignment in PERCPU_INPUT), but when linked into vmlinux,
everything would be shifted down by 0x20 bytes.
This manifests as one of the CPUs getting lost when running
kvm-unit-tests or starting any VM and subsequent soft lockup on a Cortex
A72 device.
Fixes: 30c953911c43 ("kvm: arm64: Set up hyp percpu data for nVHE")
Signed-off-by: Jamie Iles <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
Acked-by: David Brazdil <[email protected]>
Cc: David Brazdil <[email protected]>
Cc: Marc Zyngier <[email protected]>
Cc: Will Deacon <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
|
|
Fix build errors when CONFIG_TYPEC_QCOM_PMIC=y and
CONFIG_USB_ROLE_SWITCH=m by limiting the former to =m when
USB_ROLE_SWITCH also =m.
powerpc64-linux-ld: drivers/usb/typec/qcom-pmic-typec.o: in function `.qcom_pmic_typec_remove':
qcom-pmic-typec.c:(.text+0x28): undefined reference to `.usb_role_switch_set_role'
powerpc64-linux-ld: qcom-pmic-typec.c:(.text+0x64): undefined reference to `.usb_role_switch_put'
powerpc64-linux-ld: drivers/usb/typec/qcom-pmic-typec.o: in function `.qcom_pmic_typec_check_connection':
qcom-pmic-typec.c:(.text+0x120): undefined reference to `.usb_role_switch_set_role'
powerpc64-linux-ld: drivers/usb/typec/qcom-pmic-typec.o: in function `.qcom_pmic_typec_probe':
qcom-pmic-typec.c:(.text+0x360): undefined reference to `.fwnode_usb_role_switch_get'
powerpc64-linux-ld: qcom-pmic-typec.c:(.text+0x4e4): undefined reference to `.usb_role_switch_put'
Fixes: 6c8cf3695176 ("usb: typec: Add QCOM PMIC typec detection driver")
Cc: [email protected]
Cc: Wesley Cheng <[email protected]>
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Randy Dunlap <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Heikki Krogerus <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Two bugs for Cadence USB3 gadget driver
- TD_SIZE entry at descriptor is error for multiple-trb use case
- Possible use uninitialized variables
* tag 'usb-fixes-v5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdns3: gadget: calculate TD_SIZE based on TD
usb: cdns3: gadget: initialize link_trb as NULL
|
|
ASUS ROG Strix also uses ALC1220-VB-DT, so adjust the mapping and add
profile name to let userspace pick correct UCM profile.
BugLink: https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/issues/1031
Signed-off-by: Kai-Heng Feng <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
There is a spelling mistake in the Kconfig. Fix it.
Signed-off-by: Colin Ian King <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
This Kconfig entry should declare a dependency on OF
Fixes: 67b27dbeac4d ("phy: qualcomm: Add Synopsys 28nm Hi-Speed USB PHY driver")
Signed-off-by: Bryan O'Donoghue <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
This Kconfig entry should declare a dependency on OF
Fixes: 6076967a500c ("phy: qualcomm: usb: Add SuperSpeed PHY driver")
Reported-by: kernel test robot <[email protected]>
Link: https://lkml.org/lkml/2020/11/13/414
Signed-off-by: Bryan O'Donoghue <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The Intel Keem Bay eMMC PHY is only present on Intel Keem Bay SoCs.
Hence add a dependency on ARCH_KEEMBAY, to prevent asking the user about
this driver when configuring a kernel without Intel Keem Bay platform
support.
Fixes: 885c4f4d6cf448f6 ("phy: intel: Add Keem Bay eMMC PHY support")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The TRB entry TD_SIZE is the packet number for the TD (request) but not the
each TRB, so it only needs to be assigned for the first TRB during the TD,
and the value of it is for TD too.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Peter Chen <[email protected]>
|
|
There is an uninitialized variable "link_trb" usage at function cdns3_ep_run_transfer.
Fixed it by initialize "link_trb" as NULL.
Fixes: 4e218882eb5a ("usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer")
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Peter Chen <[email protected]>
|
|
Mid callback needs to be called only when valid data is
read into pages.
These patches address a problem found during decryption offload:
CIFS: VFS: trying to dequeue a deleted mid
that could cause a refcount use after free:
Workqueue: smb3decryptd smb2_decrypt_offload [cifs]
Signed-off-by: Rohith Surabattula <[email protected]>
Reviewed-by: Pavel Shilovsky <[email protected]>
CC: Stable <[email protected]> #5.4+
Signed-off-by: Steve French <[email protected]>
|
|
When reconnect happens Mid queue can be corrupted when both
demultiplex and offload thread try to dequeue the MID from the
pending list.
These patches address a problem found during decryption offload:
CIFS: VFS: trying to dequeue a deleted mid
that could cause a refcount use after free:
Workqueue: smb3decryptd smb2_decrypt_offload [cifs]
Signed-off-by: Rohith Surabattula <[email protected]>
Reviewed-by: Pavel Shilovsky <[email protected]>
CC: Stable <[email protected]> #5.4+
Signed-off-by: Steve French <[email protected]>
|
|
cifs_reconnect needs to be called only from demultiplex thread.
skip cifs_reconnect in offload thread. So, cifs_reconnect will be
called by demultiplex thread in subsequent request.
These patches address a problem found during decryption offload:
CIFS: VFS: trying to dequeue a deleted mid
that can cause a refcount use after free:
[ 1271.389453] Workqueue: smb3decryptd smb2_decrypt_offload [cifs]
[ 1271.389456] RIP: 0010:refcount_warn_saturate+0xae/0xf0
[ 1271.389457] Code: fa 1d 6a 01 01 e8 c7 44 b1 ff 0f 0b 5d c3 80 3d e7 1d 6a 01 00 75 91 48 c7 c7 d8 be 1d a2 c6 05 d7 1d 6a 01 01 e8 a7 44 b1 ff <0f> 0b 5d c3 80 3d c5 1d 6a 01 00 0f 85 6d ff ff ff 48 c7 c7 30 bf
[ 1271.389458] RSP: 0018:ffffa4cdc1f87e30 EFLAGS: 00010286
[ 1271.389458] RAX: 0000000000000000 RBX: ffff9974d2809f00 RCX: ffff9974df898cc8
[ 1271.389459] RDX: 00000000ffffffd8 RSI: 0000000000000027 RDI: ffff9974df898cc0
[ 1271.389460] RBP: ffffa4cdc1f87e30 R08: 0000000000000004 R09: 00000000000002c0
[ 1271.389460] R10: 0000000000000000 R11: 0000000000000001 R12: ffff9974b7fdb5c0
[ 1271.389461] R13: ffff9974d2809f00 R14: ffff9974ccea0a80 R15: ffff99748e60db80
[ 1271.389462] FS: 0000000000000000(0000) GS:ffff9974df880000(0000) knlGS:0000000000000000
[ 1271.389462] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1271.389463] CR2: 000055c60f344fe4 CR3: 0000001031a3c002 CR4: 00000000003706e0
[ 1271.389465] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1271.389465] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1271.389466] Call Trace:
[ 1271.389483] cifs_mid_q_entry_release+0xce/0x110 [cifs]
[ 1271.389499] smb2_decrypt_offload+0xa9/0x1c0 [cifs]
[ 1271.389501] process_one_work+0x1e8/0x3b0
[ 1271.389503] worker_thread+0x50/0x370
[ 1271.389504] kthread+0x12f/0x150
[ 1271.389506] ? process_one_work+0x3b0/0x3b0
[ 1271.389507] ? __kthread_bind_mask+0x70/0x70
[ 1271.389509] ret_from_fork+0x22/0x30
Signed-off-by: Rohith Surabattula <[email protected]>
Reviewed-by: Pavel Shilovsky <[email protected]>
CC: Stable <[email protected]> #5.4+
Signed-off-by: Steve French <[email protected]>
|
|
kmemleak reported a memory leak allocated in query_info() when cifs is
working with modefromsid.
backtrace:
[<00000000aeef6a1e>] slab_post_alloc_hook+0x58/0x510
[<00000000b2f7a440>] __kmalloc+0x1a0/0x390
[<000000006d470ebc>] query_info+0x5b5/0x700 [cifs]
[<00000000bad76ce0>] SMB2_query_acl+0x2b/0x30 [cifs]
[<000000001fa09606>] get_smb2_acl_by_path+0x2f3/0x720 [cifs]
[<000000001b6ebab7>] get_smb2_acl+0x75/0x90 [cifs]
[<00000000abf43904>] cifs_acl_to_fattr+0x13b/0x1d0 [cifs]
[<00000000a5372ec3>] cifs_get_inode_info+0x4cd/0x9a0 [cifs]
[<00000000388e0a04>] cifs_revalidate_dentry_attr+0x1cd/0x510 [cifs]
[<0000000046b6b352>] cifs_getattr+0x8a/0x260 [cifs]
[<000000007692c95e>] vfs_getattr_nosec+0xa1/0xc0
[<00000000cbc7d742>] vfs_getattr+0x36/0x40
[<00000000de8acf67>] vfs_statx_fd+0x4a/0x80
[<00000000a58c6adb>] __do_sys_newfstat+0x31/0x70
[<00000000300b3b4e>] __x64_sys_newfstat+0x16/0x20
[<000000006d8e9c48>] do_syscall_64+0x37/0x80
This patch add missing kfree for pntsd when mounting modefromsid option.
Cc: Stable <[email protected]> # v5.4+
Signed-off-by: Namjae Jeon <[email protected]>
Reviewed-by: Aurelien Aptel <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
|
|
pseries guest kernels have a FWNMI handler for SRESET and MCE NMIs,
which is basically the same as the regular handlers for those
interrupts.
The system reset FWNMI handler did not have a KVM guest test in it,
although it probably should have because the guest can itself run
guests.
Commit 4f50541f6703b ("powerpc/64s/exception: Move all interrupt
handlers to new style code gen macros") convert the handler faithfully
to avoid a KVM test with a "clever" trick to modify the IKVM_REAL
setting to 0 when the fwnmi handler is to be generated (PPC_PSERIES=y).
This worked when the KVM test was generated in the interrupt entry
handlers, but a later patch moved the KVM test to the common handler,
and the common handler macro is expanded below the fwnmi entry. This
prevents the KVM test from being generated even for the 0x100 entry
point as well.
The result is NMI IPIs in the host kernel when a guest is running will
use gest registers. This goes particularly badly when an HPT guest is
running and the MMU is set to guest mode.
Remove this trickery and just generate the test always.
Fixes: 9600f261acaa ("powerpc/64s/exception: Move KVM test to common code")
Cc: [email protected] # v5.7+
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
In newer versions of virtio-scsi we just reset the timer when an a
command times out, so TMFs are never sent for the cmd time out case.
However, in older kernels and for the TMF inject cases, we can still get
resets and we end up just failing immediately so the guest might see the
device get offlined and IO errors.
For the older kernel cases, we want the same end result as the
modern virtio-scsi driver where we let the lower levels fire their error
handling and handle the problem. And at the upper levels we want to
wait. This patch ties the LUN reset handling into the LIO TMF code which
will just wait for outstanding commands to complete like we are doing in
the modern virtio-scsi case.
Note: I did not handle the ABORT case to keep this simple. For ABORTs
LIO just waits on the cmd like how it does for the RESET case. If
an ABORT fails, the guest OS ends up escalating to LUN RESET, so in
the end we get the same behavior where we wait on the outstanding
cmds.
Signed-off-by: Mike Christie <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
Acked-by: Stefan Hajnoczi <[email protected]>
|
|
Move code to parse lun from req's lun_buf to helper, so tmf code
can use it in the next patch.
Signed-off-by: Mike Christie <[email protected]>
Reviewed-by: Paolo Bonzini <[email protected]>
Acked-by: Jason Wang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
Acked-by: Stefan Hajnoczi <[email protected]>
|
|
We might not do the final se_cmd put from vhost_scsi_complete_cmd_work.
When the last put happens a little later then we could race where
vhost_scsi_complete_cmd_work does vhost_signal, the guest runs and sends
more IO, and vhost_scsi_handle_vq runs but does not find any free cmds.
This patch has us delay completing the cmd until the last lio core ref
is dropped. We then know that once we signal to the guest that the cmd
is completed that if it queues a new command it will find a free cmd.
Signed-off-by: Mike Christie <[email protected]>
Reviewed-by: Maurizio Lombardi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
Acked-by: Stefan Hajnoczi <[email protected]>
|
|
We currently are limited to 256 cmds per session. This leads to problems
where if the user has increased virtqueue_size to more than 2 or
cmd_per_lun to more than 256 vhost_scsi_get_tag can fail and the guest
will get IO errors.
This patch moves the cmd allocation to per vq so we can easily match
whatever the user has specified for num_queues and
virtqueue_size/cmd_per_lun. It also makes it easier to control how much
memory we preallocate. For cases, where perf is not as important and
we can use the current defaults (1 vq and 128 cmds per vq) memory use
from preallocate cmds is cut in half. For cases, where we are willing
to use more memory for higher perf, cmd mem use will now increase as
the num queues and queue depth increases.
Signed-off-by: Mike Christie <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
Reviewed-by: Maurizio Lombardi <[email protected]>
Acked-by: Stefan Hajnoczi <[email protected]>
|
|
This adds a helper check if a vq has been setup. The next patches
will use this when we move the vhost scsi cmd preallocation from per
session to per vq. In the per vq case, we only want to allocate cmds
for vqs that have actually been setup and not for all the possible
vqs.
Signed-off-by: Mike Christie <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
Acked-by: Jason Wang <[email protected]>
Acked-by: Stefan Hajnoczi <[email protected]>
|