| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
>From Intel IAA spec [1], Intel IAA does not support batch processing.
Two batch related default values for IAA are incorrect in current code:
(1) The max batch size of device is set during device initialization,
that indicates batch is supported. It should be always 0 on IAA.
(2) The max batch size of work queue is set to WQ_DEFAULT_MAX_BATCH (32)
as the default value regardless of Intel DSA or IAA device during
work queue setup and cleanup. It should be always 0 on IAA.
Fix the issues by setting the max batch size of device and max batch
size of work queue to 0 on IAA device, that means batch is not
supported.
[1]: https://cdrdv2.intel.com/v1/dl/getContent/721858
Fixes: 23084545dbb0 ("dmaengine: idxd: set max_xfer and max_batch for RO device")
Fixes: 92452a72ebdf ("dmaengine: idxd: set defaults for wq configs")
Fixes: bfe1d56091c1 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Signed-off-by: Xiaochen Shen <[email protected]>
Reviewed-by: Dave Jiang <[email protected]>
Reviewed-by: Fenghua Yu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The first IRQ is required, but IRQs 1 through (nb_phy_chans - 1) are
optional, because on some platforms (e.g. PXA168) there is a single IRQ
shared between all channels.
This change inhibits a flood of "IRQ index # not found" messages at
startup. Tested on a PXA168-based device.
Fixes: 7723f4c5ecdb ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Doug Brown <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Xin Long says:
====================
sctp: fix a NULL pointer dereference in sctp_sched_dequeue_common
This issue was triggered with SCTP_PR_SCTP_PRIO in sctp,
and caused by not checking and fixing stream->out_curr
after removing a chunk from this stream.
Patch 1 removes an unnecessary check and makes the real
fix easier to add in Patch 2.
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
A crash was reported by Zhen Chen:
list_del corruption, ffffa035ddf01c18->next is NULL
WARNING: CPU: 1 PID: 250682 at lib/list_debug.c:49 __list_del_entry_valid+0x59/0xe0
RIP: 0010:__list_del_entry_valid+0x59/0xe0
Call Trace:
sctp_sched_dequeue_common+0x17/0x70 [sctp]
sctp_sched_fcfs_dequeue+0x37/0x50 [sctp]
sctp_outq_flush_data+0x85/0x360 [sctp]
sctp_outq_uncork+0x77/0xa0 [sctp]
sctp_cmd_interpreter.constprop.0+0x164/0x1450 [sctp]
sctp_side_effects+0x37/0xe0 [sctp]
sctp_do_sm+0xd0/0x230 [sctp]
sctp_primitive_SEND+0x2f/0x40 [sctp]
sctp_sendmsg_to_asoc+0x3fa/0x5c0 [sctp]
sctp_sendmsg+0x3d5/0x440 [sctp]
sock_sendmsg+0x5b/0x70
and in sctp_sched_fcfs_dequeue() it dequeued a chunk from stream
out_curr outq while this outq was empty.
Normally stream->out_curr must be set to NULL once all frag chunks of
current msg are dequeued, as we can see in sctp_sched_dequeue_done().
However, in sctp_prsctp_prune_unsent() as it is not a proper dequeue,
sctp_sched_dequeue_done() is not called to do this.
This patch is to fix it by simply setting out_curr to NULL when the
last frag chunk of current msg is dequeued from out_curr stream in
sctp_prsctp_prune_unsent().
Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations")
Reported-by: Zhen Chen <[email protected]>
Tested-by: Caowangbao <[email protected]>
Signed-off-by: Xin Long <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Since commit 5bbbbe32a431 ("sctp: introduce stream scheduler foundations"),
sctp_stream_outq_migrate() has been called in sctp_stream_init/update to
removes those chunks to streams higher than the new max. There is no longer
need to do such check in sctp_prsctp_prune_unsent().
Signed-off-by: Xin Long <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This is a follow-up for commit 974cb0e3e7c9 ("tipc: fix uninit-value
in tipc_nl_compat_name_table_dump") where it should have type casted
sizeof(..) to int to work when TLV_GET_DATA_LEN() returns a negative
value.
syzbot reported a call trace because of it:
BUG: KMSAN: uninit-value in ...
tipc_nl_compat_name_table_dump+0x841/0xea0 net/tipc/netlink_compat.c:934
__tipc_nl_compat_dumpit+0xab2/0x1320 net/tipc/netlink_compat.c:238
tipc_nl_compat_dumpit+0x991/0xb50 net/tipc/netlink_compat.c:321
tipc_nl_compat_recv+0xb6e/0x1640 net/tipc/netlink_compat.c:1324
genl_family_rcv_msg_doit net/netlink/genetlink.c:731 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:775 [inline]
genl_rcv_msg+0x103f/0x1260 net/netlink/genetlink.c:792
netlink_rcv_skb+0x3a5/0x6c0 net/netlink/af_netlink.c:2501
genl_rcv+0x3c/0x50 net/netlink/genetlink.c:803
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0xf3b/0x1270 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x1288/0x1440 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
Reported-by: [email protected]
Fixes: 974cb0e3e7c9 ("tipc: fix uninit-value in tipc_nl_compat_name_table_dump")
Signed-off-by: Xin Long <[email protected]>
Link: https://lore.kernel.org/r/ccd6a7ea801b15aec092c3b532a883b4c5708695.1667594933.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
From ZBC-1:
- RC BASIS = 0: The RETURNED LOGICAL BLOCK ADDRESS field indicates the
highest LBA of a contiguous range of zones that are not sequential write
required zones starting with the first zone.
- RC BASIS = 1: The RETURNED LOGICAL BLOCK ADDRESS field indicates the LBA
of the last logical block on the logical unit.
The current scsi_debug READ CAPACITY response does not comply with the
above if there are one or more sequential write required zones. SCSI
initiators need a way to retrieve the largest valid LBA from SCSI
devices. Reporting the largest valid LBA if there are one or more
sequential zones requires to set the RC BASIS field in the READ CAPACITY
response to one. Hence this patch.
Cc: Douglas Gilbert <[email protected]>
Cc: Damien Le Moal <[email protected]>
Suggested-by: Damien Le Moal <[email protected]>
Signed-off-by: Bart Van Assche <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Damien Le Moal <[email protected]>
Acked-by: Douglas Gilbert <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
While BCMGENET select BROADCOM_PHY as y, but PTP_1588_CLOCK_OPTIONAL is m,
kconfig warning and build errors:
WARNING: unmet direct dependencies detected for BROADCOM_PHY
Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
Selected by [y]:
- BCMGENET [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_BROADCOM [=y] && HAS_IOMEM [=y] && ARCH_BCM2835 [=y]
drivers/net/phy/broadcom.o: In function `bcm54xx_suspend':
broadcom.c:(.text+0x6ac): undefined reference to `bcm_ptp_stop'
drivers/net/phy/broadcom.o: In function `bcm54xx_phy_probe':
broadcom.c:(.text+0x784): undefined reference to `bcm_ptp_probe'
drivers/net/phy/broadcom.o: In function `bcm54xx_config_init':
broadcom.c:(.text+0xd4c): undefined reference to `bcm_ptp_config_init'
Fixes: 99addbe31f55 ("net: broadcom: Select BROADCOM_PHY for BCMGENET")
Signed-off-by: YueHaibing <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
If CONFIG_MACSEC=m and CONFIG_OCTEONTX2_PF=y, it leads a build error:
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_pfaf_mbox_up_handler':
otx2_pf.c:(.text+0x181c): undefined reference to `cn10k_handle_mcs_event'
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_probe':
otx2_pf.c:(.text+0x437e): undefined reference to `cn10k_mcs_init'
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_remove':
otx2_pf.c:(.text+0x5031): undefined reference to `cn10k_mcs_free'
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_mbox_up_handler_mcs_intr_notify':
otx2_pf.c:(.text+0x5f11): undefined reference to `cn10k_handle_mcs_event'
Make CONFIG_OCTEONTX2_PF depends on CONFIG_MACSEC to fix it. Because
it has empty stub functions of cn10k, CONFIG_OCTEONTX2_PF can be enabled
if CONFIG_MACSEC is disabled
Fixes: c54ffc73601c ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading")
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Yang Yingliang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
While working on the nvmem description I figured out this file had the
"nvmem-cell-names" property name misspelled. Fix the typo, as
"nvmem-cells-names" has never existed.
Fixes: 603094b2cdb7 ("dt-bindings: net: Add tsnep Ethernet controller")
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Gerhard Engleder <[email protected]>
Acked-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
If transport_add_device() fails in sas_phy_add(), the kernel will crash
trying to delete the device in transport_remove_device() called from
sas_remove_host().
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000108
CPU: 61 PID: 42829 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc1+ #173
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x54/0x3d0
lr : device_del+0x37c/0x3d0
Call trace:
device_del+0x54/0x3d0
attribute_container_class_device_del+0x28/0x38
transport_remove_classdev+0x6c/0x80
attribute_container_device_trigger+0x108/0x110
transport_remove_device+0x28/0x38
sas_phy_delete+0x30/0x60 [scsi_transport_sas]
do_sas_phy_delete+0x6c/0x80 [scsi_transport_sas]
device_for_each_child+0x68/0xb0
sas_remove_children+0x40/0x50 [scsi_transport_sas]
sas_remove_host+0x20/0x38 [scsi_transport_sas]
hisi_sas_remove+0x40/0x68 [hisi_sas_main]
hisi_sas_v2_remove+0x20/0x30 [hisi_sas_v2_hw]
platform_remove+0x2c/0x60
Fix this by checking and handling return value of transport_add_device()
in sas_phy_add().
Fixes: c7ebbbce366c ("[SCSI] SAS transport class")
Suggested-by: John Garry <[email protected]>
Signed-off-by: Yang Yingliang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: John Garry <[email protected]>
Reviewed-by: Jason Yan <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
There are two problems with meson8b_devm_clk_prepare_enable(),
introduced in commit a54dc4a49045 ("net: stmmac: dwmac-meson8b:
Make the clock enabling code re-usable"):
- It doesn't pass the clk argument, but instead always the
rgmii_tx_clk of the device.
- It silently ignores the return value of devm_add_action_or_reset().
The former didn't become an actual bug until another user showed up in
the next commit 9308c47640d5 ("net: stmmac: dwmac-meson8b: add support
for the RX delay configuration"). The latter means the callers could
end up with the clock not actually prepared/enabled.
Fixes: a54dc4a49045 ("net: stmmac: dwmac-meson8b: Make the clock enabling code re-usable")
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Martin Blumenstingl <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
When iterating the VMAs, the maple state needs to be invalidated if the
tree is modified by a split or merge to ensure the maple tree node
contained in the maple state is still valid. These invalidations were
missed, so add them to the paths which alter the tree.
Reported-by: [email protected]
Fixes: 69dbe6daf104 (userfaultfd: use maple tree iterator to iterate VMAs)
Signed-off-by: Liam R. Howlett <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Fix an issue reported when performing a live migration when multipath is
configured with a short fast fail timeout of 5 seconds and also to have
no_path_retry set to fail. In this scenario, all paths would go into the
devloss state while the ibmvfc driver went through discovery to log back
in. On a loaded system, the discovery might take longer than 5 seconds,
which was resulting in all paths being marked failed, which then resulted
in a read only filesystem.
This patch changes the migration code in ibmvfc to avoid deleting rports at
all in this scenario, so we avoid losing all paths.
Signed-off-by: Brian King <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"The most important fixes here are a set of fixes for the ACPI
backlight detection refactor which landed in 6.1.
These fix regressions reported on some laptop models by making
acpi_video_backlight_use_native() always return true for now, which in
essence undoes some of the changes.
I plan to take another shot at having only 1 /sys/class/backlight
class device per panel with 6.2, with modified detection heuristics to
avoid the (known) regressions.
Highlights:
- ACPI: video: Fix regressions from 6.1 backlight refactor by making
acpi_video_backlight_use_native() always return true for now
- Misc other bugfixes and HW id additions"
* tag 'platform-drivers-x86-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: p2sb: Don't fail if unknown CPU is found
platform/x86/intel/hid: Add some ACPI device IDs
platform/x86/intel/pmt: Sapphire Rapids PMT errata fix
platform/x86: hp_wmi: Fix rfkill causing soft blocked wifi
platform/x86: touchscreen_dmi: Add info for the RCA Cambio W101 v2 2-in-1
platform/x86: ideapad-laptop: Disable touchpad_switch
ACPI: video: Add backlight=native DMI quirk for Dell G15 5515
ACPI: video: Make acpi_video_backlight_use_native() always return true
ACPI: video: Improve Chromebook checks
|
|
Akira reports:
> "make htmldocs" reports duplicate C declaration of ksize() as follows:
> /linux/Documentation/core-api/mm-api:43: ./mm/slab_common.c:1428: WARNING: Duplicate C declaration, also defined at core-api/mm-api:212.
> Declaration is '.. c:function:: size_t ksize (const void *objp)'.
> This is due to the kernel-doc comment for ksize() declaration added in
> include/linux/slab.h by commit 05a940656e1e ("slab: Introduce
> kmalloc_size_roundup()").
There is an older kernel-doc comment for ksize() definition in
mm/slab_common.c, which is not only duplicated, but also contradicts the
new one - the additional storage discovered by ksize() should not be
used by callers anymore. Delete the old kernel-doc.
Reported-by: Akira Yokosawa <[email protected]>
Link: https://lore.kernel.org/all/[email protected]/
Fixes: 05a940656e1e ("slab: Introduce kmalloc_size_roundup()")
Cc: Kees Cook <[email protected]>
Signed-off-by: Vlastimil Babka <[email protected]>
|
|
Commit 72655fb942c1 ("drm/panfrost: replace endian-specific types with
native ones") accidentally reverted part of the parent commit
7228d9d79248 ("drm/panfrost: Remove type name from internal structs")
leading to the situation that the Panfrost UAPI header still doesn't
compile correctly in C++.
Revert the accidental revert and pass me a brown paper bag.
Reported-by: Alyssa Rosenzweig <[email protected]>
Fixes: 72655fb942c1 ("drm/panfrost: replace endian-specific types with native ones")
Signed-off-by: Steven Price <[email protected]>
Reviewed-by: Alyssa Rosenzweig <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
If we're doing device replace on a zoned filesystem and discover in
scrub_enumerate_chunks() that we don't have to copy the block group it is
unlocked before it gets skipped.
But as the block group hasn't yet been locked before it leads to a locking
imbalance. To fix this simply remove the unlock.
This was uncovered by fstests' testcase btrfs/163.
Fixes: 9283b9e09a6d ("btrfs: remove lock protection for BLOCK_GROUP_FLAG_TO_COPY")
Signed-off-by: Johannes Thumshirn <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
When performing seeding on a zoned filesystem it is necessary to
initialize each zoned device's btrfs_zoned_device_info structure,
otherwise mounting the filesystem will cause a NULL pointer dereference.
This was uncovered by fstests' testcase btrfs/163.
CC: [email protected] # 5.15+
Signed-off-by: Johannes Thumshirn <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
When cloning a btrfs_device, we're not cloning the associated
btrfs_zoned_device_info structure of the device in case of a zoned
filesystem.
Later on this leads to a NULL pointer dereference when accessing the
device's zone_info for instance when setting a zone as active.
This was uncovered by fstests' testcase btrfs/161.
CC: [email protected] # 5.15+
Signed-off-by: Johannes Thumshirn <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
This reverts commit 786672e9e1a39a231806313e3c445c236588ceef.
[BUG]
Since commit 786672e9e1a3 ("btrfs: scrub: use larger block size for data
extent scrub"), btrfs scrub no longer reports errors if the corruption
is not in the first sector of a STRIPE_LEN.
The following script can expose the problem:
mkfs.btrfs -f $dev
mount $dev $mnt
xfs_io -f -c "pwrite -S 0xff 0 8k" $mnt/foobar
umount $mnt
# 13631488 is the logical bytenr of above 8K extent
btrfs-map-logical -l 13631488 -b 4096 $dev
mirror 1 logical 13631488 physical 13631488 device /dev/test/scratch1
# Corrupt the 2nd sector of that extent
xfs_io -f -c "pwrite -S 0x00 13635584 4k" $dev
mount $dev $mnt
btrfs scrub start -B $mnt
scrub done for 54e63f9f-0c30-4c84-a33b-5c56014629b7
Scrub started: Mon Nov 7 07:18:27 2022
Status: finished
Duration: 0:00:00
Total to scrub: 536.00MiB
Rate: 0.00B/s
Error summary: no errors found <<<
[CAUSE]
That offending commit enlarges the data extent scrub size from sector
size to BTRFS_STRIPE_LEN, to avoid extra scrub_block to be allocated.
But unfortunately the data extent scrub is still heavily relying on the
fact that there is only one scrub_sector per scrub_block.
Thus it will only check the first sector, and ignoring the remaining
sectors.
Furthermore the error reporting is not able to handle multiple sectors
either.
[FIX]
For now just revert the offending commit.
The consequence is just extra memory usage during scrub.
We will need a proper change to make the remaining data scrub path to
handle multiple sectors before we enlarging the data scrub size.
Reported-by: Li Zhang <[email protected]>
Signed-off-by: Qu Wenruo <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
Add ENOMEM among the error codes that don't print stack trace on
transaction abort. We've got several reports from syzbot that detects
stacks as errors but caused by limiting memory. As this is an artificial
condition we don't need to know where exactly the error happens, the
abort and error cleanup will continue like e.g. for EIO.
As the transaction aborts code needs to be inline in a lot of code, the
implementation cases about minimal bloat. The error codes are in a
separate function and the WARN uses the condition directly. This
increases the code size by 571 bytes on release build.
Alternatives considered: add -ENOMEM among the errors, this increases
size by 2340 bytes, various attempts to combine the WARN and helper
calls, increase by 700 or more bytes.
Example syzbot reports (error -12):
- https://syzkaller.appspot.com/bug?extid=5244d35be7f589cf093e
- https://syzkaller.appspot.com/bug?extid=9c37714c07194d816417
Signed-off-by: David Sterba <[email protected]>
|
|
The btrfs_alloc_dummy_root() uses ERR_PTR as the error return value
rather than NULL, if error happened, there will be a NULL pointer
dereference:
BUG: KASAN: null-ptr-deref in btrfs_free_dummy_root+0x21/0x50 [btrfs]
Read of size 8 at addr 000000000000002c by task insmod/258926
CPU: 2 PID: 258926 Comm: insmod Tainted: G W 6.1.0-rc2+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
kasan_report+0xb7/0x140
kasan_check_range+0x145/0x1a0
btrfs_free_dummy_root+0x21/0x50 [btrfs]
btrfs_test_free_space_cache+0x1a8c/0x1add [btrfs]
btrfs_run_sanity_tests+0x65/0x80 [btrfs]
init_btrfs_fs+0xec/0x154 [btrfs]
do_one_initcall+0x87/0x2a0
do_init_module+0xdf/0x320
load_module+0x3006/0x3390
__do_sys_finit_module+0x113/0x1b0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: aaedb55bc08f ("Btrfs: add tests for btrfs_get_extent")
CC: [email protected] # 4.9+
Reviewed-by: Anand Jain <[email protected]>
Signed-off-by: Zhang Xiaoxu <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
syzkaller found a failed assertion:
assertion failed: (args->devid != (u64)-1) || args->missing, in fs/btrfs/volumes.c:6921
This can be triggered when we set devid to (u64)-1 by ioctl. In this
case, the match of devid will be skipped and the match of device may
succeed incorrectly.
Patch 562d7b1512f7 introduced this function which is used to match device.
This function contains two matching scenarios, we can distinguish them by
checking the value of args->missing rather than check whether args->devid
and args->uuid is default value.
Reported-by: [email protected]
Fixes: 562d7b1512f7 ("btrfs: handle device lookup with btrfs_dev_lookup_args")
CC: [email protected] # 5.16+
Reviewed-by: Nikolay Borisov <[email protected]>
Signed-off-by: Liu Shixin <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
The conversion looks harmless, however the addr value is updated inside
the loop with the previous vm_end, which then incorrectly leads to
for_each_vma_range() iterating over stuff outside the range we care
about. Fix this by storing the end value separately. Also fix the case
where the range doesn't intersect with any vma, or if the vma itself
doesn't extend the entire range, which must mean we have hole at the
end. Both should result in an error, as per the previous behaviour.
v2: Fix the cases where the range is empty, or if there's a hole at
the end of the range
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7247
Testcase: igt@gem_userptr_blits@probe
Fixes: f683b9d61319 ("i915: use the VMA iterator")
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Matthew Auld <[email protected]>
Cc: Tvrtko Ursulin <[email protected]>
Cc: Matthew Wilcox (Oracle) <[email protected]>
Cc: Liam R. Howlett <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: Yu Zhao <[email protected]>
Reviewed-by: Liam R. Howlett <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 6f7de35b50860c345babf8ed0aa0d75f9315eee4)
Signed-off-by: Tvrtko Ursulin <[email protected]>
|
|
Currently on DG1, which does not have LLC, we hit the below
warning while rebinding an userptr invalidated object.
WARNING: CPU: 4 PID: 13008 at drivers/gpu/drm/i915/gem/i915_gem_pages.c:34 __i915_gem_object_set_pages+0x296/0x2d0 [i915]
...
RIP: 0010:__i915_gem_object_set_pages+0x296/0x2d0 [i915]
...
Call Trace:
<TASK>
i915_gem_userptr_get_pages+0x175/0x1a0 [i915]
____i915_gem_object_get_pages+0x32/0xb0 [i915]
i915_gem_object_userptr_submit_init+0x286/0x470 [i915]
eb_lookup_vmas+0x2ff/0xcf0 [i915]
? __intel_wakeref_get_first+0x55/0xb0 [i915]
i915_gem_do_execbuffer+0x785/0x21d0 [i915]
i915_gem_execbuffer2_ioctl+0xe7/0x3d0 [i915]
We shouldn't be setting the obj->cache_dirty for DGFX,
fix it.
Fixes: d70af57944a1 ("drm/i915/shmem: ensure flush during swap-in on non-LLC")
Suggested-by: Matthew Auld <[email protected]>
Reported-by: Niranjana Vishwanathapura <[email protected]>
Signed-off-by: Niranjana Vishwanathapura <[email protected]>
Acked-by: Nirmoy Das <[email protected]>
Reviewed-by: Matthew Auld <[email protected]>
Reviewed-by: Andi Shyti <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 0aeec60c76ca2631696b4228f3fc99fe3a80013d)
Signed-off-by: Tvrtko Ursulin <[email protected]>
|
|
Currently we are observing mouse cursor stuttering when using
xrandr --scaling=1.2x1.2. X scaling/transformation seems to be
doing fronbuffer rendering. When moving mouse cursor X seems to
perform several invalidates and only one DirtyFB. I.e. it seems
to be assuming updates are sent to panel while drawing is done.
Earlier we were disabling PSR in frontbuffer invalidate call back
(when drawing in X started). PSR was re-enabled in frontbuffer
flush callback (dirtyfb ioctl). This was working fine with X
scaling/transformation. Now we are just enabling continuous full
frame (cff) in PSR invalidate callback. Enabling cff doesn't
trigger any updates. It just configures PSR to send full frame
when updates are sent. I.e. there are no updates on screen before
PSR flush callback is made. X seems to be doing several updates
in frontbuffer before doing dirtyfb ioctl.
Fix this by sending single update on every invalidate callback.
Cc: José Roberto de Souza <[email protected]>
Cc: Ville Syrjälä <[email protected]>
Cc: Mika Kahola <[email protected]>
Fixes: 805f04d42a6b ("drm/i915/display/psr: Use continuos full frame to handle frontbuffer invalidations")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6679
Signed-off-by: Jouni Högander <[email protected]>
Reported-by: Brian J. Tarricone <[email protected]>
Tested-by: Brian J. Tarricone <[email protected]>
Reviewed-by: Mika Kahola <[email protected]>
Reviewed-by: José Roberto de Souza <[email protected]>
Signed-off-by: José Roberto de Souza <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit d755f89220a2b49bc90b7b520bb6edeb4adb5f01)
Signed-off-by: Tvrtko Ursulin <[email protected]>
|
|
We need to iterate over the original entries here for the sg_table,
pulling out the struct page for each one, to be remapped. However
currently this incorrectly iterates over the final dma mapped entries,
which is likely just one gigantic sg entry if the iommu is enabled,
leading to us only mapping the first struct page (and any physically
contiguous pages following it), even if there is potentially lots more
data to follow.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7306
Fixes: 1286ff739773 ("i915: add dmabuf/prime buffer sharing support.")
Signed-off-by: Matthew Auld <[email protected]>
Cc: Lionel Landwerlin <[email protected]>
Cc: Tvrtko Ursulin <[email protected]>
Cc: Ville Syrjälä <[email protected]>
Cc: Michael J. Ruhl <[email protected]>
Cc: <[email protected]> # v3.5+
Reviewed-by: Michael J. Ruhl <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 28d52f99bbca7227008cf580c9194c9b3516968e)
Signed-off-by: Tvrtko Ursulin <[email protected]>
|
|
When introducing support for R-Car V3U, which has 8 instead of 2
channels, the ECC error bitmask was extended to take into account the
extra channels, but rcar_canfd_global_error() was not updated to act
upon the extra bits.
Replace the RCANFD_GERFL_EEF[01] macros by a new macro that takes the
channel number, fixing R-Car V3U while simplifying the code.
Fixes: 45721c406dcf50d4 ("can: rcar_canfd: Add support for r8a779a0 SoC")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Biju Das <[email protected]>
Link: https://lore.kernel.org/all/4edb2ea46cc64d0532a08a924179827481e14b4f.1666951503.git.geert+renesas@glider.be
Cc: [email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
In commit a6d190f8c767 ("can: skb: drop tx skb if in listen only
mode") the priv->ctrlmode element is read even on virtual CAN
interfaces that do not create the struct can_priv at startup. This
out-of-bounds read may lead to CAN frame drops for virtual CAN
interfaces like vcan and vxcan.
This patch mainly reverts the original commit and adds a new helper
for CAN interface drivers that provide the required information in
struct can_priv.
Fixes: a6d190f8c767 ("can: skb: drop tx skb if in listen only mode")
Reported-by: Dariusz Stojaczyk <[email protected]>
Cc: Vincent Mailhol <[email protected]>
Cc: Max Staudt <[email protected]>
Signed-off-by: Oliver Hartkopp <[email protected]>
Acked-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Cc: [email protected] # 6.0.x
[mkl: patch pch_can, too]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
The read access to struct canxl_frame::len inside of a j1939 created
skbuff revealed a missing initialization of reserved and later filled
elements in struct can_frame.
This patch initializes the 8 byte CAN header with zero.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Cc: Oleksij Rempel <[email protected]>
Link: https://lore.kernel.org/linux-can/[email protected]
Reported-by: [email protected]
Signed-off-by: Oliver Hartkopp <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Cc: [email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
In commit 4b7fe92c0690 ("can: isotp: add local echo tx processing for
consecutive frames") the data flow for consecutive frames (CF) has been
reworked to improve the reliability of long data transfers.
This rework did not touch the transmission and the tx state changes of
single frame (SF) transfers which likely led to the WARN in the
isotp_tx_timer_handler() catching a wrong tx state. This patch makes use
of the improved frame processing for SF frames and sets the ISOTP_SENDING
state in isotp_sendmsg() within the cmpxchg() condition handling.
A review of the state machine and the timer handling additionally revealed
a missing echo timeout handling in the case of the burst mode in
isotp_rcv_echo() and removes a potential timer configuration uncertainty
in isotp_rcv_fc() when the receiver requests consecutive frames.
Fixes: 4b7fe92c0690 ("can: isotp: add local echo tx processing for consecutive frames")
Link: https://lore.kernel.org/linux-can/CAO4mrfe3dG7cMP1V5FLUkw7s+50c9vichigUMQwsxX4M=45QEw@mail.gmail.com/T/#u
Reported-by: Wei Chen <[email protected]>
Cc: [email protected] # v6.0
Signed-off-by: Oliver Hartkopp <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
It causes NULL pointer dereference when testing as following:
(a) use syscall(__NR_socket, 0x10ul, 3ul, 0) to create netlink socket.
(b) use syscall(__NR_sendmsg, ...) to create bond link device and vxcan
link device, and bind vxcan device to bond device (can also use
ifenslave command to bind vxcan device to bond device).
(c) use syscall(__NR_socket, 0x1dul, 3ul, 1) to create CAN socket.
(d) use syscall(__NR_bind, ...) to bind the bond device to CAN socket.
The bond device invokes the can-raw protocol registration interface to
receive CAN packets. However, ml_priv is not allocated to the dev,
dev_rcv_lists is assigned to NULL in can_rx_register(). In this case,
it will occur the NULL pointer dereference issue.
The following is the stack information:
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 122a4067 P4D 122a4067 PUD 1223c067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
RIP: 0010:can_rx_register+0x12d/0x1e0
Call Trace:
<TASK>
raw_enable_filters+0x8d/0x120
raw_enable_allfilters+0x3b/0x130
raw_bind+0x118/0x4f0
__sys_bind+0x163/0x1a0
__x64_sys_bind+0x1e/0x30
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Fixes: 4e096a18867a ("net: introduce CAN specific pointer in the struct net_device")
Signed-off-by: Zhengchao Shao <[email protected]>
Reviewed-by: Marc Kleine-Budde <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
In can_init(), dev_add_pack(&canxl_packet) is added but not removed in
can_exit(). It breaks the packet handler list and can make kernel
panic when can_init() is called for the second time.
| > modprobe can && rmmod can
| > rmmod xxx && modprobe can
|
| BUG: unable to handle page fault for address: fffffbfff807d7f4
| RIP: 0010:dev_add_pack+0x133/0x1f0
| Call Trace:
| <TASK>
| can_init+0xaa/0x1000 [can]
| do_one_initcall+0xd3/0x4e0
| ...
Fixes: fb08cba12b52 ("can: canxl: update CAN infrastructure for CAN XL frames")
Signed-off-by: Chen Zhongjin <[email protected]>
Acked-by: Oliver Hartkopp <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
[mkl: adjust subject and commit message]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: f545702b74f9 ("mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E")
Signed-off-by: Brian Norris <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/20221026124150.v4.6.I35ca9d6220ba48304438b992a76647ca8e5b126f@changeid
Signed-off-by: Ulf Hansson <[email protected]>
|
|
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: 3c4019f97978 ("mmc: tegra: HW Command Queue Support for Tegra SDMMC")
Signed-off-by: Brian Norris <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/20221026124150.v4.5.I418c9eaaf754880fcd2698113e8c3ef821a944d7@changeid
Signed-off-by: Ulf Hansson <[email protected]>
|
|
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: bb6e358169bf ("mmc: sdhci-esdhc-imx: add CMDQ support")
Signed-off-by: Brian Norris <[email protected]>
Reviewed-by: Haibo Chen <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/20221026124150.v4.4.I7d01f9ad11bacdc9213dee61b7918982aea39115@changeid
Signed-off-by: Ulf Hansson <[email protected]>
|
|
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
I only patch the bcm7216 variant even though others potentially *could*
provide the 'supports-cqe' property (and thus enable CQHCI), because
d46ba2d17f90 ("mmc: sdhci-brcmstb: Add support for Command Queuing
(CQE)") and some Broadcom folks confirm that only the 7216 variant
actually supports it.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: d46ba2d17f90 ("mmc: sdhci-brcmstb: Add support for Command Queuing (CQE)")
Signed-off-by: Brian Norris <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/20221026124150.v4.3.I6a715feab6d01f760455865e968ecf0d85036018@changeid
Signed-off-by: Ulf Hansson <[email protected]>
|
|
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but one
particular case I hit commonly enough: mmc_suspend() -> mmc_power_off().
Typically we will eventually deactivate CQE (cqhci_suspend() ->
cqhci_deactivate()), but that's not guaranteed -- in particular, if
we perform a partial (e.g., interrupted) system suspend.
The same bug was already found and fixed for two other drivers, in v5.7
and v5.9:
5cf583f1fb9c ("mmc: sdhci-msm: Deactivate CQE during SDHC reset")
df57d73276b8 ("mmc: sdhci-pci: Fix SDHCI_RESET_ALL for CQHCI for Intel
GLK-based controllers")
The latter is especially prescient, saying "other drivers using CQHCI
might benefit from a similar change, if they also have CQHCI reset by
SDHCI_RESET_ALL."
So like these other patches, deactivate CQHCI when resetting the
controller. Do this via the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: 84362d79f436 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1")
Cc: <[email protected]>
Signed-off-by: Brian Norris <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Link: https://lore.kernel.org/r/20221026124150.v4.2.I29f6a2189e84e35ad89c1833793dca9e36c64297@changeid
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Several SDHCI drivers need to deactivate command queueing in their reset
hook (see sdhci_cqhci_reset() / sdhci-pci-core.c, for example), and
several more are coming.
Those reset implementations have some small subtleties (e.g., ordering
of initialization of SDHCI vs. CQHCI might leave us resetting with a
NULL ->cqe_private), and are often identical across different host
drivers.
We also don't want to force a dependency between SDHCI and CQHCI, or
vice versa; non-SDHCI drivers use CQHCI, and SDHCI drivers might support
command queueing through some other means.
So, implement a small helper, to avoid repeating the same mistakes in
different drivers. Simply stick it in a header, because it's so small it
doesn't deserve its own module right now, and inlining to each driver is
pretty reasonable.
This is marked for -stable, as it is an important prerequisite patch for
several SDHCI controller bugfixes that follow.
Cc: <[email protected]>
Signed-off-by: Brian Norris <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/20221026124150.v4.1.Ie85faa09432bfe1b0890d8c24ff95e17f3097317@changeid
Signed-off-by: Ulf Hansson <[email protected]>
|
|
When copying a `struct ifaddrlblmsg` to the network, __ifal_reserved
remained uninitialized, resulting in a 1-byte infoleak:
BUG: KMSAN: kernel-network-infoleak in __netdev_start_xmit ./include/linux/netdevice.h:4841
__netdev_start_xmit ./include/linux/netdevice.h:4841
netdev_start_xmit ./include/linux/netdevice.h:4857
xmit_one net/core/dev.c:3590
dev_hard_start_xmit+0x1dc/0x800 net/core/dev.c:3606
__dev_queue_xmit+0x17e8/0x4350 net/core/dev.c:4256
dev_queue_xmit ./include/linux/netdevice.h:3009
__netlink_deliver_tap_skb net/netlink/af_netlink.c:307
__netlink_deliver_tap+0x728/0xad0 net/netlink/af_netlink.c:325
netlink_deliver_tap net/netlink/af_netlink.c:338
__netlink_sendskb net/netlink/af_netlink.c:1263
netlink_sendskb+0x1d9/0x200 net/netlink/af_netlink.c:1272
netlink_unicast+0x56d/0xf50 net/netlink/af_netlink.c:1360
nlmsg_unicast ./include/net/netlink.h:1061
rtnl_unicast+0x5a/0x80 net/core/rtnetlink.c:758
ip6addrlbl_get+0xfad/0x10f0 net/ipv6/addrlabel.c:628
rtnetlink_rcv_msg+0xb33/0x1570 net/core/rtnetlink.c:6082
...
Uninit was created at:
slab_post_alloc_hook+0x118/0xb00 mm/slab.h:742
slab_alloc_node mm/slub.c:3398
__kmem_cache_alloc_node+0x4f2/0x930 mm/slub.c:3437
__do_kmalloc_node mm/slab_common.c:954
__kmalloc_node_track_caller+0x117/0x3d0 mm/slab_common.c:975
kmalloc_reserve net/core/skbuff.c:437
__alloc_skb+0x27a/0xab0 net/core/skbuff.c:509
alloc_skb ./include/linux/skbuff.h:1267
nlmsg_new ./include/net/netlink.h:964
ip6addrlbl_get+0x490/0x10f0 net/ipv6/addrlabel.c:608
rtnetlink_rcv_msg+0xb33/0x1570 net/core/rtnetlink.c:6082
netlink_rcv_skb+0x299/0x550 net/netlink/af_netlink.c:2540
rtnetlink_rcv+0x26/0x30 net/core/rtnetlink.c:6109
netlink_unicast_kernel net/netlink/af_netlink.c:1319
netlink_unicast+0x9ab/0xf50 net/netlink/af_netlink.c:1345
netlink_sendmsg+0xebc/0x10f0 net/netlink/af_netlink.c:1921
...
This patch ensures that the reserved field is always initialized.
Reported-by: syzbot+3553517af6020c4f2813f1003fe76ef3cbffe98d@syzkaller.appspotmail.com
Fixes: 2a8cc6c89039 ("[IPV6] ADDRCONF: Support RFC3484 configurable address selection policy table.")
Signed-off-by: Alexander Potapenko <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We have accessing P2SB from a very few places for quite known hardware.
When a new SoC appears in intel-family.h it's not obvious that it needs
to be added to p2sb.c as well. Instead, provide default BDF and refactor
p2sb_get_devfn() to always succeed. If in the future we would need to
exclude something, we may add a list of unsupported IDs.
Without this change the iTCO on Intel Comet Lake SoCs became unavailable:
i801_smbus 0000:00:1f.4: failed to create iTCO device
Fixes: 5c7b9167ddf8 ("i2c: i801: convert to use common P2SB accessor")
Reported-and-tested-by: Jarkko Nikula <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Add INTC1076 (JasonLake), INTC1077 (MeteorLake) and INTC1078 (RaptorLake)
devices IDs.
Signed-off-by: Ivan Hu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
On Sapphire Rapids, due to a hardware issue affecting the PUNIT telemetry
region, reads that are not done in QWORD quantities and alignment may
return incorrect data. Use a custom 64-bit copy for this region.
Signed-off-by: David E. Box <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
After upgrading BIOS to U82 01.02.01 Rev.A, the console is flooded
strange char "^@" which printed out every second and makes login
nearly impossible. Also the below messages were shown both in console
and journal/dmesg every second:
usb 1-3: Device not responding to setup address.
usb 1-3: device not accepting address 4, error -71
usb 1-3: device descriptor read/all, error -71
usb usb1-port3: unable to enumerate USB device
Wifi is soft blocked by checking rfkill. When unblocked manually,
after few seconds it would be soft blocked again. So I was suspecting
something triggered rfkill to soft block wifi. At the end it was
fixed by removing hp_wmi module.
The root cause is the way hp-wmi driver handles command 1B on
post-2009 BIOS. In pre-2009 BIOS, command 1Bh return 0x4 to indicate
that BIOS no longer controls the power for the wireless devices.
Signed-off-by: Jorge Lopez <[email protected]>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216468
Reviewed-by: Mario Limonciello <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Cc: [email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Add touchscreen info for the RCA Cambio W101 v2 2-in-1.
Link: https://github.com/onitake/gsl-firmware/discussions/193
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Ideapads for "Lenovo Yoga 3 Pro 1370" and "ZhaoYang K4e-IML" do not
use EC to switch touchpad.
Reading VPCCMD_R_TOUCHPAD will return zero thus touchpad may be blocked
unexpectedly.
Signed-off-by: Manyi Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
The Dell G15 5515 has the WMI interface (and WMI call returns) expected
by the nvidia-wmi-ec-backlight interface. But the backlight class device
registered by the nvidia-wmi-ec-backlight driver does not actually work.
The amdgpu_bl0 native GPU backlight class device does actually work,
add a backlight=native DMI quirk for this.
Reported-by: Iris <[email protected]>
Reviewed-by: Daniel Dadap <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
---
Changes in v2:
- Add a comment that this needs to be revisited when dynamic-mux
support gets added (suggested by: Daniel Dadap)
|
|
Testing has shown that there are quite a few laptop models which rely
on native backlight control and which do not support ACPI video bus
backlight control, causing __acpi_video_get_backlight_type() to return
vendor. Known Windows laptop models affected by this are:
Acer Aspire 1640
HP Compaq nc6120
IBM ThinkPad X40
System76 Starling Star1
and the following MacBook models are affected too:
Apple MacBook 2.1
Apple MacBook 4.1
Apple MacBook Pro 7.1
the list of affected Windows laptop models is likely just the top of
the iceberg. So for now lets undo the change to not register native
backlight class devices when __acpi_video_get_backlight_type() != native.
Since as part of the backlight-detect refactor the detection code now
relies on the GPU drivers calling acpi_video_backlight_use_native() to
learn that native backlight support is available we cannot just remove
the acpi_video_backlight_use_native() calls from the GPU drivers.
Instead modify acpi_video_backlight_use_native() to always return true
for now. This is meant as a temporary work-around, which will be removed
again when the heuristics from __acpi_video_get_backlight_type() have
been improved so that they will return native on affected models.
Reported-by: Matthew Garrett <[email protected]>
Reported-by: John Warriner <[email protected]>
Reported-by: Scott Ostrander <[email protected]>
Reported-by: Matthias Rampke <[email protected]>
Reported-by: Milan Hodoscek <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
If setsockopt with option name of TCP_REPAIR_OPTIONS and opt_code
of TCPOPT_SACK_PERM is called to enable sack after data is sent
and dupacks are received , it will trigger a warning in function
tcp_verify_left_out() as follows:
============================================
WARNING: CPU: 8 PID: 0 at net/ipv4/tcp_input.c:2132
tcp_timeout_mark_lost+0x154/0x160
tcp_enter_loss+0x2b/0x290
tcp_retransmit_timer+0x50b/0x640
tcp_write_timer_handler+0x1c8/0x340
tcp_write_timer+0xe5/0x140
call_timer_fn+0x3a/0x1b0
__run_timers.part.0+0x1bf/0x2d0
run_timer_softirq+0x43/0xb0
__do_softirq+0xfd/0x373
__irq_exit_rcu+0xf6/0x140
The warning is caused in the following steps:
1. a socket named socketA is created
2. socketA enters repair mode without build a connection
3. socketA calls connect() and its state is changed to TCP_ESTABLISHED
directly
4. socketA leaves repair mode
5. socketA calls sendmsg() to send data, packets_out and sack_outs(dup
ack receives) increase
6. socketA enters repair mode again
7. socketA calls setsockopt with TCPOPT_SACK_PERM to enable sack
8. retransmit timer expires, it calls tcp_timeout_mark_lost(), lost_out
increases
9. sack_outs + lost_out > packets_out triggers since lost_out and
sack_outs increase repeatly
In function tcp_timeout_mark_lost(), tp->sacked_out will be cleared if
Step7 not happen and the warning will not be triggered. As suggested by
Denis and Eric, TCP_REPAIR_OPTIONS should be prohibited if data was
already sent.
socket-tcp tests in CRIU has been tested as follows:
$ sudo ./test/zdtm.py run -t zdtm/static/socket-tcp* --keep-going \
--ignore-taint
socket-tcp* represent all socket-tcp tests in test/zdtm/static/.
Fixes: b139ba4e90dc ("tcp: Repair connection-time negotiated parameters")
Signed-off-by: Lu Wei <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|