aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2014-03-06Target/sbc: Fix sbc_copy_prot for offset scattersSagi Grimberg1-16/+22
When copying between device and command protection scatters we must take into account that device scatters might be offset and we might copy outside scatter range. Thus for each cmd prot scatter we must take the min between cmd prot scatter, dev prot scatter, and whats left (and loop in case we havn't copied enough from/to cmd prot scatter). Example (single t_prot_sg of len 2048): kernel: sbc_dif_copy_prot: se_cmd=ffff880380aaf970, left=2048, len=2048, dev_prot_sg_offset=3072, dev_prot_sg_len=4096 kernel: isert: se_cmd=ffff880380aaf970 PI error found type 0 at sector 0x2600 expected 0x0 vs actual 0x725f, lba=2580 Instead of copying 2048 from offset 3072 (copying junk outside sg limit 4096), we must to copy 1024 and continue to next sg until we complete cmd prot scatter. This issue was found using iSER T10-PI offload over rd_mcp (wasn't discovered with fileio since file_dev prot sglists are never offset). Changes from v1: - Fix sbc_copy_prot copy length miss-calculation Changes from v0: - Removed psg->offset consideration for psg_len computation - Removed sg->offset consideration for offset condition - Added copied consideraiton for len computation - Added copied offset to paddr when doing memcpy Signed-off-by: Sagi Grimberg <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2014-03-07Merge remote-tracking branches 'spi/fix/ath79', 'spi/fix/atmel', ↵Mark Brown6-17/+35
'spi/fix/coldfire', 'spi/fix/fsl-dspi', 'spi/fix/imx' and 'spi/fix/topcliff-pch' into spi-linus
2014-03-07powerpc: Align p_dyn, p_rela and p_st symbolsAnton Blanchard1-0/+1
The 64bit relocation code places a few symbols in the text segment. These symbols are only 4 byte aligned where they need to be 8 byte aligned. Add an explicit alignment. Signed-off-by: Anton Blanchard <[email protected]> Cc: [email protected] Tested-by: Laurent Dufour <[email protected]> Signed-off-by: Benjamin Herrenschmidt <[email protected]>
2014-03-07powerpc/tm: Fix crash when forking inside a transactionMichael Neuling1-0/+9
When we fork/clone we currently don't copy any of the TM state to the new thread. This results in a TM bad thing (program check) when the new process is switched in as the kernel does a tmrechkpt with TEXASR FS not set. Also, since R1 is from userspace, we trigger the bad kernel stack pointer detection. So we end up with something like this: Bad kernel stack pointer 0 at c0000000000404fc cpu 0x2: Vector: 700 (Program Check) at [c00000003ffefd40] pc: c0000000000404fc: restore_gprs+0xc0/0x148 lr: 0000000000000000 sp: 0 msr: 9000000100201030 current = 0xc000001dd1417c30 paca = 0xc00000000fe00800 softe: 0 irq_happened: 0x01 pid = 0, comm = swapper/2 WARNING: exception is not recoverable, can't continue The below fixes this by flushing the TM state before we copy the task_struct to the clone. To do this we go through the tmreclaim patch, which removes the checkpointed registers from the CPU and transitions the CPU out of TM suspend mode. Hence we need to call tmrechkpt after to restore the checkpointed state and the TM mode for the current task. To make this fail from userspace is simply: tbegin li r0, 2 sc <boom> Kudos to Adhemerval Zanella Neto for finding this. Signed-off-by: Michael Neuling <[email protected]> cc: Adhemerval Zanella Neto <[email protected]> cc: [email protected] Signed-off-by: Benjamin Herrenschmidt <[email protected]>
2014-03-07Merge branch 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux ↵Dave Airlie1-1/+1
into drm-fixes one more radeon fix. * 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux: drm/radeon/atom: select the proper number of lanes in transmitter setup
2014-03-06drm/radeon/atom: select the proper number of lanes in transmitter setupAlex Deucher1-1/+1
We need to check for DVI vs. HDMI when setting up duallink since HDMI is single link only. Fixes 4k modes on newer asics. bug: https://bugs.freedesktop.org/show_bug.cgi?id=75223 Signed-off-by: Alex Deucher <[email protected]> Cc: [email protected]
2014-03-07MAINTAINERS: add maintainer entry for TDA998x driverRussell King1-0/+6
Add a maintainers entry for the TDA998x driver. Rob Clark has handed this driver over to me to look after. Acked-by: Rob Clark <[email protected]> Signed-off-by: Russell King <[email protected]> Signed-off-by: Dave Airlie <[email protected]>
2014-03-07drm: fix bochs kconfig dependenciesGerd Hoffmann1-0/+1
Signed-off-by: Gerd Hoffmann <[email protected]> Signed-off-by: Dave Airlie <[email protected]>
2014-03-07Merge branch 'drm-armada-fixes' of ↵Dave Airlie1-9/+1
git://ftp.arm.linux.org.uk/~rmk/linux-cubox into drm-fixes fix for kfifo api change. * 'drm-armada-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox: DRM: armada: fix use of kfifo_put()
2014-03-07Merge branch 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux ↵Dave Airlie17-26/+22
into drm-fixes a few more radeon fixes. * 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux: drm/radeon/dpm: fix typo in EVERGREEN_SMC_FIRMWARE_HEADER_softRegisters drm/radeon/cik: fix typo in documentation drm/radeon: silence GCC warning on 32 bit drm/radeon: resume old pm late drm/radeon: TTM must be init with cpu-visible VRAM, v2
2014-03-06drm/radeon/dpm: fix typo in EVERGREEN_SMC_FIRMWARE_HEADER_softRegistersAlex Deucher1-1/+1
Should be at 0x8 rather than 0. fixes: https://bugzilla.kernel.org/show_bug.cgi?id=60523 Noticed by ArtForz on #radeon Signed-off-by: Alex Deucher <[email protected]> Cc: [email protected]
2014-03-06drm/radeon/cik: fix typo in documentationAlex Deucher1-1/+1
Copy-paste typo. Signed-off-by: Alex Deucher <[email protected]>
2014-03-06drm/radeon: silence GCC warning on 32 bitPaul Bolle1-1/+1
Building radeon_ttm.o on 32 bit x86 triggers a warning: In file included from include/asm-generic/bug.h:13:0, from [...]/arch/x86/include/asm/bug.h:38, from include/linux/bug.h:4, from include/drm/drm_mm.h:39, from include/drm/drm_vma_manager.h:26, from include/drm/ttm/ttm_bo_api.h:35, from drivers/gpu/drm/radeon/radeon_ttm.c:32: drivers/gpu/drm/radeon/radeon_ttm.c: In function 'radeon_ttm_gtt_read': include/linux/kernel.h:712:17: warning: comparison of distinct pointer types lacks a cast [enabled by default] (void) (&_min1 == &_min2); \ ^ drivers/gpu/drm/radeon/radeon_ttm.c:938:22: note: in expansion of macro 'min' ssize_t cur_size = min(size, PAGE_SIZE - off); ^ Silence this warning by using min_t(). Since cur_size will never be negative and its upper bound is PAGE_SIZE, we can change its type to size_t and use min_t(size_t, [...]) here. Signed-off-by: Paul Bolle <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Reviewed-by: Christian König <[email protected]>
2014-03-06drm/radeon: resume old pm lateAlex Deucher15-23/+16
Moving the pm resume up in the init order to fix dpm seems to have regressed somes cases with the old pm code. Move it back to late resume. Signed-off-by: Alex Deucher <[email protected]>
2014-03-06drm/radeon: TTM must be init with cpu-visible VRAM, v2Lauri Kasanen1-0/+3
Without this, a bo may get created in the cpu-inaccessible vram. Before the CP engines get setup, all copies are done via cpu memcpy. This means that the cpu tries to read from inaccessible memory, fails, and the radeon module proceeds to disable acceleration. Doing this has no downsides, as the real VRAM size gets set as soon as the CP engines get init. This is a candidate for 3.14 fixes. v2: Add comment on why the function is used Signed-off-by: Lauri Kasanen <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Reviewed-by: Christian König <[email protected]> Cc: [email protected]
2014-03-06firewire: ohci: fix probe failure with Agere/LSI controllersStefan Richter1-13/+2
Since commit bd972688eb24 "firewire: ohci: Fix 'failed to read phy reg' on FW643 rev8", there is a high chance that firewire-ohci fails to initialize LSI née Agere controllers. https://bugzilla.kernel.org/show_bug.cgi?id=65151 Peter Hurley points out the reason: IEEE 1394a:2000 clause 5A.1 (or IEEE 1394:2008 clause 17.2.1) say: "The PHY shall insure that no more than 10 ms elapse from the reassertion of LPS until the interface is reset. The link shall not assert LReq until the reset is complete." In other words, the link needs to give the PHY at least 10 ms to get the interface operational. With just the msleep(1) in bd972688eb24, the first read_phy_reg() during ohci_enable() may happen before the phy-link interface reset was finished, and fail. Due to the high variability of msleep(n) with small n, this failure was not fully reproducible, and not apparent at all with low CONFIG_HZ setting. On the other hand, Peter can no longer reproduce the issue with FW643 rev8. The read phy reg failures that happened back then may have had an unrelated cause. So, just revert bd972688eb24, except for the valid comment on TSB82AA2 cards. Reported-by: Mikhail Gavrilov Reported-by: Jay Fenlason <[email protected]> Reported-by: Clemens Ladisch <[email protected]> Reported-by: Peter Hurley <[email protected]> Cc: [email protected] # v3.10+ Signed-off-by: Stefan Richter <[email protected]>
2014-03-06dm thin: fix Documentation for held metadata root featureMike Snitzer1-3/+2
The Documentation for the thin provisioning target's held metadata root feature was incorrect. It is now available and the value for the held metadata root is in block units (not 512b sectors). Signed-off-by: Mike Snitzer <[email protected]>
2014-03-06x86, trace: Further robustify CR2 handling vs tracingPeter Zijlstra1-10/+23
Building on commit 0ac09f9f8cd1 ("x86, trace: Fix CR2 corruption when tracing page faults") this patch addresses another few issues: - Now that read_cr2() is lifted into trace_do_page_fault(), we should pass the address to trace_page_fault_entries() to avoid it re-reading a potentially changed cr2. - Put both trace_do_page_fault() and trace_page_fault_entries() under CONFIG_TRACING. - Mark both fault entry functions {,trace_}do_page_fault() as notrace to avoid getting __mcount or other function entry trace callbacks before we've observed CR2. - Mark __do_page_fault() as noinline to guarantee the function tracer does get to see the fault. Cc: <[email protected]> Cc: <[email protected]> Acked-by: Steven Rostedt <[email protected]> Signed-off-by: Peter Zijlstra <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: H. Peter Anvin <[email protected]>
2014-03-06ACPI / EC: Clear stale EC events on Samsung systemsKieran Clancy1-0/+64
A number of Samsung notebooks (530Uxx/535Uxx/540Uxx/550Pxx/900Xxx/etc) continue to log events during sleep (lid open/close, AC plug/unplug, battery level change), which accumulate in the EC until a buffer fills. After the buffer is full (tests suggest it holds 8 events), GPEs stop being triggered for new events. This state persists on wake or even on power cycle, and prevents new events from being registered until the EC is manually polled. This is the root cause of a number of bugs, including AC not being detected properly, lid close not triggering suspend, and low ambient light not triggering the keyboard backlight. The bug also seemed to be responsible for performance issues on at least one user's machine. Juan Manuel Cabo found the cause of bug and the workaround of polling the EC manually on wake. The loop which clears the stale events is based on an earlier patch by Lan Tianyu (see referenced attachment). This patch: - Adds a function acpi_ec_clear() which polls the EC for stale _Q events at most ACPI_EC_CLEAR_MAX (currently 100) times. A warning is logged if this limit is reached. - Adds a flag EC_FLAGS_CLEAR_ON_RESUME which is set to 1 if the DMI system vendor is Samsung. This check could be replaced by several more specific DMI vendor/product pairs, but it's likely that the bug affects more Samsung products than just the five series mentioned above. Further, it should not be harmful to run acpi_ec_clear() on systems without the bug; it will return immediately after finding no data waiting. - Runs acpi_ec_clear() on initialisation (boot), from acpi_ec_add() - Runs acpi_ec_clear() on wake, from acpi_ec_unblock_transactions() References: https://bugzilla.kernel.org/show_bug.cgi?id=44161 References: https://bugzilla.kernel.org/show_bug.cgi?id=45461 References: https://bugzilla.kernel.org/show_bug.cgi?id=57271 References: https://bugzilla.kernel.org/attachment.cgi?id=126801 Suggested-by: Juan Manuel Cabo <[email protected]> Signed-off-by: Kieran Clancy <[email protected]> Reviewed-by: Lan Tianyu <[email protected]> Reviewed-by: Dennis Jansen <[email protected]> Tested-by: Kieran Clancy <[email protected]> Tested-by: Juan Manuel Cabo <[email protected]> Tested-by: Dennis Jansen <[email protected]> Tested-by: Maurizio D'Addona <[email protected]> Tested-by: San Zamoyski <[email protected]> Cc: All applicable <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2014-03-06cpufreq: Initialize governor for a new policy under policy->rwsemViresh Kumar1-0/+2
policy->rwsem is used to lock access to all parts of code modifying struct cpufreq_policy, but it's not used on a new policy created by __cpufreq_add_dev(). Because of that, if cpufreq_update_policy() is called in a tight loop on one CPU in parallel with offline/online of another CPU, then the following crash can be triggered: Unable to handle kernel NULL pointer dereference at virtual address 00000020 pgd = c0003000 [00000020] *pgd=80000000004003, *pmd=00000000 Internal error: Oops: 206 [#1] PREEMPT SMP ARM PC is at __cpufreq_governor+0x10/0x1ac LR is at cpufreq_update_policy+0x114/0x150 ---[ end trace f23a8defea6cd706 ]--- Kernel panic - not syncing: Fatal exception CPU0: stopping CPU: 0 PID: 7136 Comm: mpdecision Tainted: G D W 3.10.0-gd727407-00074-g979ede8 #396 [<c0afe180>] (notifier_call_chain+0x40/0x68) from [<c02a23ac>] (__blocking_notifier_call_chain+0x40/0x58) [<c02a23ac>] (__blocking_notifier_call_chain+0x40/0x58) from [<c02a23d8>] (blocking_notifier_call_chain+0x14/0x1c) [<c02a23d8>] (blocking_notifier_call_chain+0x14/0x1c) from [<c0803c68>] (cpufreq_set_policy+0xd4/0x2b8) [<c0803c68>] (cpufreq_set_policy+0xd4/0x2b8) from [<c0803e7c>] (cpufreq_init_policy+0x30/0x98) [<c0803e7c>] (cpufreq_init_policy+0x30/0x98) from [<c0805a18>] (__cpufreq_add_dev.isra.17+0x4dc/0x7a4) [<c0805a18>] (__cpufreq_add_dev.isra.17+0x4dc/0x7a4) from [<c0805d38>] (cpufreq_cpu_callback+0x58/0x84) [<c0805d38>] (cpufreq_cpu_callback+0x58/0x84) from [<c0afe180>] (notifier_call_chain+0x40/0x68) [<c0afe180>] (notifier_call_chain+0x40/0x68) from [<c02812dc>] (__cpu_notify+0x28/0x44) [<c02812dc>] (__cpu_notify+0x28/0x44) from [<c0aeed90>] (_cpu_up+0xf4/0x1dc) [<c0aeed90>] (_cpu_up+0xf4/0x1dc) from [<c0aeeed4>] (cpu_up+0x5c/0x78) [<c0aeeed4>] (cpu_up+0x5c/0x78) from [<c0aec808>] (store_online+0x44/0x74) [<c0aec808>] (store_online+0x44/0x74) from [<c03a40f4>] (sysfs_write_file+0x108/0x14c) [<c03a40f4>] (sysfs_write_file+0x108/0x14c) from [<c03517d4>] (vfs_write+0xd0/0x180) [<c03517d4>] (vfs_write+0xd0/0x180) from [<c0351ca8>] (SyS_write+0x38/0x68) [<c0351ca8>] (SyS_write+0x38/0x68) from [<c0205de0>] (ret_fast_syscall+0x0/0x30) Fix that by taking locks at appropriate places in __cpufreq_add_dev() as well. Reported-by: Saravana Kannan <[email protected]> Suggested-by: Srivatsa S. Bhat <[email protected]> Signed-off-by: Viresh Kumar <[email protected]> [rjw: Changelog] Signed-off-by: Rafael J. Wysocki <[email protected]>
2014-03-06cpufreq: Initialize policy before making it available for others to useViresh Kumar1-14/+14
Policy must be fully initialized before it is being made available for use by others. Otherwise cpufreq_cpu_get() would be able to grab a half initialized policy structure that might not have affected_cpus (for example) populated. Then, anybody accessing those fields will get a wrong value and that will lead to unpredictable results. In order to fix this, do all the necessary initialization before we make the policy structure available via cpufreq_cpu_get(). That will guarantee that any code accessing fields of the policy will get correct data from them. Reported-by: Saravana Kannan <[email protected]> Signed-off-by: Viresh Kumar <[email protected]> [rjw: Changelog] Signed-off-by: Rafael J. Wysocki <[email protected]>
2014-03-06cpufreq: use cpufreq_cpu_get() to avoid cpufreq_get() race conditionsAaron Plattner1-14/+7
If a module calls cpufreq_get while cpufreq is initializing, it's possible for it to be called after cpufreq_driver is set but before cpufreq_cpu_data is written during subsys_interface_register. This happens because cpufreq_get doesn't take the cpufreq_driver_lock around its use of cpufreq_cpu_data. Fix this by using cpufreq_cpu_get(cpu) to look up the policy rather than reading it out of cpufreq_cpu_data directly. cpufreq_cpu_get() takes the appropriate locks to prevent this race from happening. Since it's possible for policy to be NULL if the caller passes in an invalid CPU number or calls the function before cpufreq is initialized, delete the BUG_ON(!policy) and simply return 0. Don't try to return -ENOENT because that's negative and the function returns an unsigned integer. References: https://bbs.archlinux.org/viewtopic.php?id=177934 Signed-off-by: Aaron Plattner <[email protected]> Cc: 3.13+ <[email protected]> # 3.13+ Signed-off-by: Rafael J. Wysocki <[email protected]>
2014-03-05clk: shmobile: rcar-gen2: Use kick bit to allow Z clock frequency changeBenoit Cousson1-2/+34
The Z clock frequency change is effective only after setting the kick bit located in the FRQCRB register. Without that, the CA15 CPUs clock rate will never change. Fix that by checking if the kick bit is cleared and enable it to make the clock rate change effective. The bit is cleared automatically upon completion. Signed-off-by: Benoit Cousson <[email protected]> Acked-by: Laurent Pinchart <[email protected]> Signed-off-by: Mike Turquette <[email protected]>
2014-03-05dm thin: fix noflush suspend IO queueingJoe Thornber1-2/+72
i) by the time DM core calls the postsuspend hook the dm_noflush flag has been cleared. So the old thin_postsuspend did nothing. We need to use the presuspend hook instead. ii) There was a race between bios leaving DM core and arriving in the deferred queue. thin_presuspend now sets a 'requeue' flag causing all bios destined for that thin to be requeued back to DM core. Then it requeues all held IO, and all IO on the deferred queue (destined for that thin). Finally postsuspend clears the 'requeue' flag. Signed-off-by: Joe Thornber <[email protected]> Signed-off-by: Mike Snitzer <[email protected]>
2014-03-05dm thin: fix deadlock in __requeue_bio_listJoe Thornber1-6/+7
The spin lock in requeue_io() was held for too long, allowing deadlock. Don't worry, due to other issues addressed in the following "dm thin: fix noflush suspend IO queueing" commit, this code was never called. Fix this by taking the spin lock for a much shorter period of time. Signed-off-by: Joe Thornber <[email protected]> Signed-off-by: Mike Snitzer <[email protected]>
2014-03-05dm thin: fix out of data space handlingJoe Thornber1-45/+102
Ideally a thin pool would never run out of data space; the low water mark would trigger userland to extend the pool before we completely run out of space. However, many small random IOs to unprovisioned space can consume data space at an alarming rate. Adjust your low water mark if you're frequently seeing "out-of-data-space" mode. Before this fix, if data space ran out the pool would be put in PM_READ_ONLY mode which also aborted the pool's current metadata transaction (data loss for any changes in the transaction). This had a side-effect of needlessly compromising data consistency. And retry of queued unserviceable bios, once the data pool was resized, could initiate changes to potentially inconsistent pool metadata. Now when the pool's data space is exhausted transition to a new pool mode (PM_OUT_OF_DATA_SPACE) that allows metadata to be changed but data may not be allocated. This allows users to remove thin volumes or discard data to recover data space. The pool is no longer put in PM_READ_ONLY mode in response to the pool running out of data space. And PM_READ_ONLY mode no longer aborts the pool's current metadata transaction. Also, set_pool_mode() will now notify userspace when the pool mode is changed. Signed-off-by: Joe Thornber <[email protected]> Signed-off-by: Mike Snitzer <[email protected]>
2014-03-05dm thin: ensure user takes action to validate data and metadata consistencyMike Snitzer5-29/+135
If a thin metadata operation fails the current transaction will abort, whereby causing potential for IO layers up the stack (e.g. filesystems) to have data loss. As such, set THIN_METADATA_NEEDS_CHECK_FLAG in the thin metadata's superblock which: 1) requires the user verify the thin metadata is consistent (e.g. use thin_check, etc) 2) suggests the user verify the thin data is consistent (e.g. use fsck) The only way to clear the superblock's THIN_METADATA_NEEDS_CHECK_FLAG is to run thin_repair. On metadata operation failure: abort current metadata transaction, set pool in read-only mode, and now set the needs_check flag. As part of this change, constraints are introduced or relaxed: * don't allow a pool to transition to write mode if needs_check is set * don't allow data or metadata space to be resized if needs_check is set * if a thin pool's metadata space is exhausted: the kernel will now force the user to take the pool offline for repair before the kernel will allow the metadata space to be extended. Also, update Documentation to include information about when the thin provisioning target commits metadata, how it handles metadata failures and running out of space. Signed-off-by: Mike Snitzer <[email protected]> Signed-off-by: Joe Thornber <[email protected]>
2014-03-05NFSv4: Fail the truncate() if the lock/open stateid is invalidTrond Myklebust1-3/+6
If the open stateid could not be recovered, or the file locks were lost, then we should fail the truncate() operation altogether. Reported-by: Andy Adamson <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Trond Myklebust <[email protected]>
2014-03-05NFSv4.1 Fail data server I/O if stateid represents a lost lockAndy Adamson1-4/+6
Signed-off-by: Andy Adamson <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Trond Myklebust <[email protected]>
2014-03-05NFSv4: Fix the return value of nfs4_select_rw_stateidTrond Myklebust1-11/+3
In commit 5521abfdcf4d6 (NFSv4: Resend the READ/WRITE RPC call if a stateid change causes an error), we overloaded the return value of nfs4_select_rw_stateid() to cause it to return -EWOULDBLOCK if an RPC call is outstanding that would cause the NFSv4 lock or open stateid to change. That is all redundant when we actually copy the stateid used in the read/write RPC call that failed, and check that against the current stateid. It is doubly so, when we consider that in the NFSv4.1 case, we also set the stateid's seqid to the special value '0', which means 'match the current valid stateid'. Reported-by: Andy Adamson <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Trond Myklebust <[email protected]>
2014-03-05NFSv4: nfs4_stateid_is_current should return 'true' for an invalid stateidTrond Myklebust1-2/+3
When nfs4_set_rw_stateid() can fails by returning EIO to indicate that the stateid is completely invalid, then it makes no sense to have it trigger a retry of the READ or WRITE operation. Instead, we should just have it fall through and attempt a recovery. This fixes an infinite loop in which the client keeps replaying the same bad stateid back to the server. Reported-by: Andy Adamson <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Cc: [email protected] # 3.10+ Signed-off-by: Trond Myklebust <[email protected]>
2014-03-05ALSA: usb-audio: Add quirk for Logitech Webcam C500Takashi Iwai1-0/+1
Logitech C500 (046d:0807) needs the same workaround like other Logitech Webcams. Cc: <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2014-03-05ALSA: hda - Use analog beep for Thinkpads with AD1984 codecsTakashi Iwai1-0/+3
For making the driver behavior compatible with the earlier kernels, use the analog beep in the loopback path instead of the digital beep. Cc: <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2014-03-05ALSA: hda - Add missing loopback merge path for AD1884/1984 codecsTakashi Iwai1-0/+1
The mixer widget (NID 0x20) of AD1884 and AD1984 codecs isn't connected directly to the actual I/O paths but only via another mixer widget (NID 0x21). We need a similar fix as we did for AD1882. Cc: <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2014-03-05pinctrl: sirf: fix kernel panic in gpio_lock_as_irqBarry Song1-2/+2
commit 655dada6277991 causes kernel panic, this patch fixes it. [ 1.197816] [ffffffee] *pgd=0d7fd821, *pte=00000000, *ppte=00000000 [ 1.204070] Internal error: Oops: 17 [#1] PREEMPT SMP ARM [ 1.209447] Modules linked in: [ 1.212490] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.0-rc1 #3 [ 1.218737] task: cd03c000 ti: cd040000 task.ti: cd040000 [ 1.224127] PC is at gpiod_lock_as_irq+0xc/0x64 [ 1.228634] LR is at sirfsoc_gpio_irq_startup+0x18/0x44 [ 1.233842] pc : [<c01d3990>] lr : [<c01d1c38>] psr: a0000193 [ 1.233842] sp : cd041d30 ip : 00000000 fp : 00000000 [ 1.245296] r10: 00000000 r9 : cd023db4 r8 : 60000113 [ 1.250505] r7 : 0000003e r6 : cd023dd4 r5 : c06bfa54 r4 : cd023d80 [ 1.257014] r3 : 00000020 r2 : 00000000 r1 : ffffffea r0 : ffffffea [ 1.263526] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel [ 1.270903] Control: 10c53c7d Table: 00004059 DAC: 00000015 [ 1.276631] Process swapper/0 (pid: 1, stack limit = 0xcd040240) [ 1.282620] Stack: (0xcd041d30 to 0xcd042000) [ 1.286963] 1d20: cd023d80 c01d1c38 c01d1c20 cd023d80 [ 1.295124] 1d40: 00000001 c0068438 cd023d80 ccb6d880 cd023dd4 c0067044 0000718e c006719c [ 1.286963] 1d20: cd023d80 c01d1c38 c01d1c20 cd023d80 [ 1.295124] 1d40: 00000001 c0068438 cd023d80 ccb6d880 cd023dd4 c0067044 0000718e c006719c [ 1.295124] 1d40: 00000001 c0068438 cd023d80 ccb6d880 cd023dd4 c0067044 0000718e c006719c [ 1.303283] 1d60: 00000800 00000083 ccb6d880 cd023d80 c02b41d8 00000083 0000003e ccb7c410 [ 1.311442] 1d80: 00000000 c00671dc 00000083 0000003e c02b41d8 cd3dd5c0 0000003e ccb7c634 [ 1.319601] 1da0: cd040030 c00672a8 cd3dd5c0 ccb7c410 ccb6d340 ccb7c410 ccb6d340 cd3dd400 [ 1.327760] 1dc0: cd3dd410 c02b4434 ccb7c410 c01265a8 00000001 cd3dd410 c0687108 00000000 [ 1.335919] 1de0: c0687108 00000000 00000000 c0240170 c0240158 cd3dd410 c06c30d0 c023e8bc [ 1.344079] 1e00: c023e9d4 00000000 cd3dd410 c023e9d4 c0682150 c023cf88 cd003e98 cd2d50c4 [ 1.352238] 1e20: cd3dd410 cd3dd444 c06822f0 c023e768 cd3dd418 cd3dd410 c06822f0 c023de14 [ 1.360397] 1e40: cd3dd418 00000000 cd3dd410 c023c398 cd041e78 cd041ea8 cd3dd400 cd3dd410 [ 1.368556] 1e60: 00000083 00000000 cd3dd400 cd3dd410 00000083 000000c8 c04e00c8 c023fee8 [ 1.376715] 1e80: 00000000 cd041ea8 cd3dd400 00000001 00000083 c024048c c0435ef8 c0434dec [ 1.384874] 1ea0: c068da58 c04c6d04 c0682150 c0435ef8 ffffffff 00000000 00000000 c068da58 [ 1.393033] 1ec0: 00000020 00000000 00000000 00000000 c05dabb8 00000007 c068d640 c068d640 [ 1.401193] 1ee0: c04c247c c04c249c 00000000 c00088e8 cd004c00 c043bbb8 cd029180 c03812a0 [ 1.409352] 1f00: 00000000 00000000 60000113 c0673728 60000113 c0673728 00000000 00000000 [ 1.417511] 1f20: cd7fce01 c0390a54 00000065 c003a81c c049e8bc 00000007 cd7fce0e 00000007 [ 1.425670] 1f40: 00000000 c05dabb8 00000007 c068d640 c068d640 c04c050c c04e00c8 00000065 [ 1.433829] 1f60: c04e00c0 c04c0c54 00000007 00000007 c04c050c c037d8fc cd03c000 c004322c [ 1.441988] 1f80: c0662b40 0000d640 c03737c0 00000000 00000000 00000000 00000000 00000000 [ 1.450147] 1fa0: 00000000 c03737cc 00000000 c000e478 00000000 00000000 00000000 00000000 [ 1.458307] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.466467] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 0002d481 05014092 [ 1.474640] [<c01d3990>] (gpiod_lock_as_irq) from [<c01d1c38>] (sirfsoc_gpio_irq_startup+0x18/0x44) [ 1.483661] [<c01d1c38>] (sirfsoc_gpio_irq_startup) from [<c0068438>] (irq_startup+0x34/0x6c) [ 1.492163] [<c0068438>] (irq_startup) from [<c0067044>] (__setup_irq+0x450/0x4b8) [ 1.499714] [<c0067044>] (__setup_irq) from [<c00671dc>] (request_threaded_irq+0xa8/0x128) [ 1.507960] [<c00671dc>] (request_threaded_irq) from [<c00672a8>] (request_any_context_irq+0x4c/0x7c) [ 1.517164] [<c00672a8>] (request_any_context_irq) from [<c02b4434>] (gpio_extcon_probe+0x144/0x1d4) [ 1.526279] [<c02b4434>] (gpio_extcon_probe) from [<c0240170>] (platform_drv_probe+0x18/0x48) [ 1.534783] [<c0240170>] (platform_drv_probe) from [<c023e8bc>] (driver_probe_device+0x120/0x238) [ 1.543641] [<c023e8bc>] (driver_probe_device) from [<c023cf88>] (bus_for_each_drv+0x58/0x8c) [ 1.552143] [<c023cf88>] (bus_for_each_drv) from [<c023e768>] (device_attach+0x74/0x88) [ 1.560126] [<c023e768>] (device_attach) from [<c023de14>] (bus_probe_device+0x84/0xa8) [ 1.568113] [<c023de14>] (bus_probe_device) from [<c023c398>] (device_add+0x440/0x520) [ 1.576012] [<c023c398>] (device_add) from [<c023fee8>] (platform_device_add+0xb4/0x214) [ 1.584084] [<c023fee8>] (platform_device_add) from [<c024048c>] (platform_device_register_full+0xb8/0xdc) [ 1.593719] [<c024048c>] (platform_device_register_full) from [<c04c6d04>] (sirfsoc_init_late+0xec/0xf4) [ 1.603185] [<c04c6d04>] (sirfsoc_init_late) from [<c04c249c>] (init_machine_late+0x20/0x28) [ 1.611603] [<c04c249c>] (init_machine_late) from [<c00088e8>] (do_one_initcall+0xf8/0x144) [ 1.619934] [<c00088e8>] (do_one_initcall) from [<c04c0c54>] (kernel_init_freeable+0x13c/0x1dc) [ 1.628620] [<c04c0c54>] (kernel_init_freeable) from [<c03737cc>] (kernel_init+0xc/0x118) Signed-off-by: Barry Song <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2014-03-05Merge tag 'drm-intel-fixes-2014-03-04' of ↵Dave Airlie6-28/+38
ssh://git.freedesktop.org/git/drm-intel into drm-fixes Small fixes all around, mostly stable material. Please pull. * tag 'drm-intel-fixes-2014-03-04' of ssh://git.freedesktop.org/git/drm-intel: drm/i915: Reject >165MHz modes w/ DVI monitors drm/i915: fix assert_cursor on BDW drm/i915: vlv: reserve GT power context early drm/i915: fix pch pci device enumeration drm/i915: Resolving the memory region conflict for Stolen area drm/i915: use backlight legacy combination mode also for i915gm/i945gm
2014-03-05spi: atmel: add missing spi_master_{resume,suspend} calls to PM callbacksWenyou Yang1-1/+16
The PM callbacks implemented by the spi-atmel driver don't call spi_master_{resume,suspend}, fix that. Signed-off-by: Wenyou Yang <[email protected]> Signed-off-by: Mark Brown <[email protected]>
2014-03-05spi: coldfire-qspi: Fix getting correct address for *mcfqspiAxel Lin1-2/+4
dev_get_drvdata() returns the address of master rather than mcfqspi. Fixes: af361079 (spi/coldfire-qspi: Drop extra calls to spi_master_get in suspend/resume functions) Signed-off-by: Axel Lin <[email protected]> Signed-off-by: Mark Brown <[email protected]> Cc: [email protected]
2014-03-05spi: fsl-dspi: Fix getting correct address for masterAxel Lin1-3/+3
Current code set platform drvdata to dspi. However, the code in dspi_suspend() and dspi_resume() assumes the drvdata is the address of master. Fix it by setting platform drvdata to master. Signed-off-by: Axel Lin <[email protected]> Signed-off-by: Mark Brown <[email protected]> Cc: [email protected]
2014-03-05pinctrl: sh-pfc: r8a7791: SD1_CLK fixMagnus Damm1-2/+4
Fix the SD1_CLK handling for r8a7791. Without this patch it is impossible to request all pins needed for SDHI1 on the Koelsch board. Signed-off-by: Magnus Damm <[email protected]> Acked-by: Laurent Pinchart <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2014-03-05pinctrl: msm: make PINCTRL_MSM bool instead of tristateJosh Cartwright1-1/+1
Modular builds of pinctrl-msm break due to handle_bad_irq being unexported for module use. For now, make PINCTRL_MSM 'bool'. Signed-off-by: Josh Cartwright <[email protected]> Reviewed-by: Bjorn Andersson <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2014-03-05pinctrl: sunxi: Fix interrupt register offset calculationHans de Goede1-3/+3
This fixing setting the interrupt type for eints >= 8. Signed-off-by: Hans de Goede <[email protected]> Acked-by: Maxime Ripard <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2014-03-05pinctrl: sunxi: Fix masking when setting irq typeHans de Goede1-1/+1
Signed-off-by: Hans de Goede <[email protected]> Acked-by: Maxime Ripard <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2014-03-05pinctrl: sunxi: use chained_irq_{enter, exit} for GIC compatibilityChen-Yu Tsai1-0/+4
On tha Allwinner A20 SoC, the external interrupts on the pin controller device are connected to the GIC. Without chained_irq_{enter, exit}, external GPIO interrupts, such as used by mmc core card detect, cause the system to hang. This issue was first encountered during my attempt to get out-of-band interrupts for WiFi on the Cubietruck working. With David's new series of sunci-mci using mmc slot-gpio for (GPIO interrupt based) card detection, removing the SD card also causes my Cubietruck to hang. This problem should extend to all Allwinner A20 based boards. With this fix, the system no longer hangs when I remove or insert the SD card. /proc/interrupts show that the interrupt has correctly fired. However the system still does not detect card removal/insertion. I believe this is another unrelated issue. Cc: [email protected] Signed-off-by: Chen-Yu Tsai <[email protected]> Acked-by: Maxime Ripard <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2014-03-04iser-target: Fix command leak for tx_desc->comp_llnode_batchNicholas Bellinger2-6/+46
This patch addresses a number of active I/O shutdown issues related to isert_cmd descriptors being leaked that are part of a completion interrupt coalescing batch. This includes adding logic in isert_cq_tx_comp_err() to drain any associated tx_desc->comp_llnode_batch, as well as isert_cq_drain_comp_llist() to drain any associated isert_conn->conn_comp_llist. Also, set tx_desc->llnode_active in isert_init_send_wr() in order to determine when work requests need to be skipped in isert_cq_tx_work() exception path code. Finally, update isert_init_send_wr() to only allow interrupt coalescing when ISER_CONN_UP. Acked-by: Sagi Grimberg <[email protected]> Cc: Or Gerlitz <[email protected]> Cc: <[email protected]> #3.13+ Signed-off-by: Nicholas Bellinger <[email protected]>
2014-03-04iser-target: Ignore completions for FRWRs in isert_cq_tx_workNicholas Bellinger2-2/+7
This patch changes IB_WR_FAST_REG_MR + IB_WR_LOCAL_INV related work requests to include a ISER_FRWR_LI_WRID value in order to signal isert_cq_tx_work() that these requests should be ignored. This is necessary because even though IB_SEND_SIGNALED is not set for either work request, during a QP failure event the work requests will be returned with exception status from the TX completion queue. v2 changes: - Rename ISER_FRWR_LI_WRID -> ISER_FASTREG_LI_WRID (Sagi) Acked-by: Sagi Grimberg <[email protected]> Cc: Or Gerlitz <[email protected]> Cc: <[email protected]> #3.12+ Signed-off-by: Nicholas Bellinger <[email protected]>
2014-03-04iser-target: Fix post_send_buf_count for RDMA READ/WRITENicholas Bellinger1-6/+8
This patch fixes the incorrect setting of ->post_send_buf_count related to RDMA WRITEs + READs where isert_rdma_rw->send_wr_num was not being taken into account. This includes incrementing ->post_send_buf_count within isert_put_datain() + isert_get_dataout(), decrementing within __isert_send_completion() + isert_response_completion(), and clearing wr->send_wr_num within isert_completion_rdma_read() This is necessary because even though IB_SEND_SIGNALED is not set for RDMA WRITEs + READs, during a QP failure event the work requests will be returned with exception status from the TX completion queue. Acked-by: Sagi Grimberg <[email protected]> Cc: Or Gerlitz <[email protected]> Cc: <[email protected]> #3.10+ Signed-off-by: Nicholas Bellinger <[email protected]>
2014-03-04iscsi/iser-target: Fix isert_conn->state hung shutdown issuesNicholas Bellinger4-60/+55
This patch addresses a couple of different hug shutdown issues related to wait_event() + isert_conn->state. First, it changes isert_conn->conn_wait + isert_conn->conn_wait_comp_err from waitqueues to completions, and sets ISER_CONN_TERMINATING from within isert_disconnect_work(). Second, it splits isert_free_conn() into isert_wait_conn() that is called earlier in iscsit_close_connection() to ensure that all outstanding commands have completed before continuing. Finally, it breaks isert_cq_comp_err() into seperate TX / RX related code, and adds logic in isert_cq_rx_comp_err() to wait for outstanding commands to complete before setting ISER_CONN_DOWN and calling complete(&isert_conn->conn_wait_comp_err). Acked-by: Sagi Grimberg <[email protected]> Cc: Or Gerlitz <[email protected]> Cc: <[email protected]> #3.10+ Signed-off-by: Nicholas Bellinger <[email protected]>
2014-03-04iscsi/iser-target: Use list_del_init for ->i_conn_nodeNicholas Bellinger3-14/+14
There are a handful of uses of list_empty() for cmd->i_conn_node within iser-target code that expect to return false once a cmd has been removed from the per connect list. This patch changes all uses of list_del -> list_del_init in order to ensure that list_empty() returns false as expected. Acked-by: Sagi Grimberg <[email protected]> Cc: Or Gerlitz <[email protected]> Cc: <[email protected]> #3.10+ Signed-off-by: Nicholas Bellinger <[email protected]>
2014-03-04iscsi-target: Fix iscsit_get_tpg_from_np tpg_state bugNicholas Bellinger1-1/+1
This patch fixes a bug in iscsit_get_tpg_from_np() where the tpg->tpg_state sanity check was looking for TPG_STATE_FREE, instead of != TPG_STATE_ACTIVE. The latter is expected during a normal TPG shutdown once the tpg_state goes into TPG_STATE_INACTIVE in order to reject any new incoming login attempts. Cc: <[email protected]> #3.10+ Signed-off-by: Nicholas Bellinger <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.