aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2020-11-16bnxt_en: read EEPROM A2h address using page 0Edwin Peer1-1/+1
The module eeprom address range returned by bnxt_get_module_eeprom() should be 256 bytes of A0h address space, the lower half of the A2h address space, and page 0 for the upper half of the A2h address space. Fix the firmware call by passing page_number 0 for the A2h slave address space. Fixes: 42ee18fe4ca2 ("bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO") Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16net: ipa: lock when freeing transactionAlex Elder1-3/+12
Transactions sit on one of several lists, depending on their state (allocated, pending, complete, or polled). A spinlock protects against concurrent access when transactions are moved between these lists. Transactions are also reference counted. A newly-allocated transaction has an initial count of 1; a transaction is released in gsi_trans_free() only if its decremented reference count reaches 0. Releasing a transaction includes removing it from the polled (or if unused, allocated) list, so the spinlock is acquired when we release a transaction. The reference count is used to allow a caller to synchronously wait for a committed transaction to complete. In this case, the waiter takes an extra reference to the transaction *before* committing it (so it won't be freed), and releases its reference (calls gsi_trans_free()) when it is done with it. Similarly, gsi_channel_update() takes an extra reference to ensure a transaction isn't released before the function is done operating on it. Until the transaction is moved to the completed list (by this function) it won't be freed, so this reference is taken "safely." But in the quiesce path, we want to wait for the "last" transaction, which we find in the completed or polled list. Transactions on these lists can be freed at any time, so we (try to) prevent that by taking the reference while holding the spinlock. Currently gsi_trans_free() decrements a transaction's reference count unconditionally, acquiring the lock to remove the transaction from its list *only* when the count reaches 0. This does not protect the quiesce path, which depends on the lock to ensure its extra reference prevents release of the transaction. Fix this by only dropping the last reference to a transaction in gsi_trans_free() while holding the spinlock. Fixes: 9dd441e4ed575 ("soc: qcom: ipa: GSI transactions") Reported-by: Stephen Boyd <[email protected]> Signed-off-by: Alex Elder <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16net/tls: fix corrupted data in recvmsgVadim Fedorenko1-1/+1
If tcp socket has more data than Encrypted Handshake Message then tls_sw_recvmsg will try to decrypt next record instead of returning full control message to userspace as mentioned in comment. The next message - usually Application Data - gets corrupted because it uses zero copy for decryption that's why the data is not stored in skb for next iteration. Revert check to not decrypt next record if current is not Application Data. Fixes: 692d7b5d1f91 ("tls: Fix recvmsg() to be able to peek across multiple records") Signed-off-by: Vadim Fedorenko <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16net: qualcomm: rmnet: Fix incorrect receive packet handling during cleanupSubash Abhinov Kasiviswanathan1-0/+5
During rmnet unregistration, the real device rx_handler is first cleared followed by the removal of rx_handler_data after the rcu synchronization. Any packets in the receive path may observe that the rx_handler is NULL. However, there is no check when dereferencing this value to use the rmnet_port information. This fixes following splat by adding the NULL check. Unable to handle kernel NULL pointer dereference at virtual address 000000000000000d pc : rmnet_rx_handler+0x124/0x284 lr : rmnet_rx_handler+0x124/0x284 rmnet_rx_handler+0x124/0x284 __netif_receive_skb_core+0x758/0xd74 __netif_receive_skb+0x50/0x17c process_backlog+0x15c/0x1b8 napi_poll+0x88/0x284 net_rx_action+0xbc/0x23c __do_softirq+0x20c/0x48c Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation") Signed-off-by: Sean Tranchetti <[email protected]> Signed-off-by: Subash Abhinov Kasiviswanathan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16net: mvneta: fix possible memory leak in mvneta_swbm_add_rx_fragmentLorenzo Bianconi1-2/+3
Recycle the page running page_pool_put_full_page() in mvneta_swbm_add_rx_fragment routine when the last descriptor contains just the FCS or if the received packet contains more than MAX_SKB_FRAGS fragments Fixes: ca0e014609f0 ("net: mvneta: move skb build after descriptors processing") Signed-off-by: Lorenzo Bianconi <[email protected]> Link: https://lore.kernel.org/r/df6a2bad70323ee58d3901491ada31c1ca2a40b9.1605291228.git.lorenzo@kernel.org Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16net: stmmac: Use rtnl_lock/unlock on netif_set_real_num_rx_queues() callWong Vee Khee1-0/+2
Fix an issue where dump stack is printed on suspend resume flow due to netif_set_real_num_rx_queues() is not called with rtnl_lock held(). Fixes: 686cff3d7022 ("net: stmmac: Fix incorrect location to set real_num_rx|tx_queues") Reported-by: Christophe ROULLIER <[email protected]> Tested-by: Christophe ROULLIER <[email protected]> Cc: Alexandre TORGUE <[email protected]> Reviewed-by: Ong Boon Leong <[email protected]> Signed-off-by: Wong Vee Khee <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16net: bridge: add missing counters to ndo_get_stats64 callbackHeiner Kallweit1-0/+1
In br_forward.c and br_input.c fields dev->stats.tx_dropped and dev->stats.multicast are populated, but they are ignored in ndo_get_stats64. Fixes: 28172739f0a2 ("net: fix 64 bit counters on 32 bit arches") Signed-off-by: Heiner Kallweit <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16net: ethernet: ti: cpsw: fix error return code in cpsw_probe()Zhang Changzhong1-0/+1
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 83a8471ba255 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization") Reported-by: Hulk Robot <[email protected]> Signed-off-by: Zhang Changzhong <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16net: stmmac: dwmac-intel-plat: fix error return code in intel_eth_plat_probe()Zhang Changzhong1-1/+3
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 9efc9b2b04c7 ("net: stmmac: Add dwmac-intel-plat for GBE driver") Reported-by: Hulk Robot <[email protected]> Signed-off-by: Zhang Changzhong <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16Merge Intel catpt DSP fixes into asoc-5.10Mark Brown1-5/+4
2020-11-16qlcnic: fix error return code in qlcnic_83xx_restart_hw()Zhang Changzhong1-1/+2
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 3ced0a88cd4c ("qlcnic: Add support to run firmware POST") Reported-by: Hulk Robot <[email protected]> Signed-off-by: Zhang Changzhong <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16cx82310_eth: fix error return code in cx82310_bind()Zhang Changzhong1-1/+2
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: ca139d76b0d9 ("cx82310_eth: re-enable ethernet mode after router reboot") Reported-by: Hulk Robot <[email protected]> Signed-off-by: Zhang Changzhong <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16Merge tag 'arm-soc-fixes-v5.10-2' of ↵Linus Torvalds48-139/+128
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "Around one third of the fixes this time are for dts files that list their ethernet controller as using 'phy-mode="rgmii"' but are changed to 'phy-mode="rgmii-id"' now, because the PHY drivers (realtek, ksz9031, dp83867, ...) now configure the internal delay based on that when they used to stay on the hardware default. The long story is archived at https://lore.kernel.org/netdev/CAMj1kXEEF_Un-4NTaD5iUN0NoZYaJQn-rPediX0S6oRiuVuW-A@mail.gmail.com/ I was trying to hold off on the bugfixes until there was a solution that would avoid breaking all boards, but that does not seem to be happening any time soon, so I am now sending the correct version of the dts files to ensure that at least these machines can use their network devices again. The other changes this time are: - Updating the MAINTAINER lists for Allwinner and Samsung SoCs - Multiple i.MX8MN machines get updates for their CPU operating points to match the data sheet - A revert for a dts patch that caused a regression in USB support on Odroid U3 - Two fixes for the AMD Tee driver, addressing a memory leak and missing locking - Mark the network subsystem on qoriq-fman3 as cache coherent for correctness as better performance. - Minor dts fixes elsewhere, addressing dtc warnings and similar problems" * tag 'arm-soc-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits) ARM: dts: exynos: revert "add input clock to CMU in Exynos4412 Odroid" ARM: dts: imx50-evk: Fix the chip select 1 IOMUX arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point ARM: dts: stm32: Keep VDDA LDO1 always on on DHCOM ARM: dts: stm32: Enable thermal sensor support on stm32mp15xx-dhcor ARM: dts: stm32: Define VIO regulator supply on DHCOM ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2 ARM: dts: stm32: Fix TA3-GPIO-C key on STM32MP1 DHCOM PDK2 arm64: dts: renesas: r8a774e1: Add missing audio_clk_b tee: amdtee: synchronize access to shm list tee: amdtee: fix memory leak due to reset of global shm list arm64: dts: agilex/stratix10: Fix qspi node compatible ARM: dts: imx6q-prti6q: fix PHY address ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy arm64: dts imx8mn: Remove non-existent USB OTG2 arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio arm64: dts: fsl: DPAA FMan DMA operations are coherent arm64: dts: fsl: fix endianness issue of rcpm arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up ...
2020-11-16drm/i915/selftests: Fix wrong return value of perf_request_latency()Zhang Xiaoxu1-1/+3
If intel context create failed, the perf_request_latency() will return 0 rather than error, because we doesn't initialize the return value. Fixes: 25c26f18ea79 ("drm/i915/selftests: Measure dispatch latency") Reported-by: Hulk Robot <[email protected]> Signed-off-by: Zhang Xiaoxu <[email protected]> Reviewed-by: Mika Kuoppala <[email protected]> Signed-off-by: Chris Wilson <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit 19384452052a1e0525e663bfbdd62ac1399bb647) Signed-off-by: Rodrigo Vivi <[email protected]>
2020-11-16drm/i915/selftests: Fix wrong return value of perf_series_engines()Zhang Xiaoxu1-1/+3
If intel context create failed, the perf_series_engines() will return 0 rather than error, because we doesn't initialize the return value. Fixes: cbfd3a0c5a55 ("drm/i915/selftests: Add request throughput measurement to perf") Reported-by: Hulk Robot <[email protected]> Signed-off-by: Zhang Xiaoxu <[email protected]> Reviewed-by: Mika Kuoppala <[email protected]> Signed-off-by: Chris Wilson <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit 01d708840c26c9532579677eaca942363a009fd5) Signed-off-by: Rodrigo Vivi <[email protected]>
2020-11-16drm/i915: Avoid memory leak with more than 16 workarounds on a listTvrtko Ursulin1-1/+3
I forgot to free the old list when growing past 16 entries. Luckily, as much as I checked, none of the current platforms has more than 16 workarounds on a single list. Signed-off-by: Tvrtko Ursulin <[email protected]> Fixes: 452420d22d5b ("drm/i915: Fuse per-context workaround handling with the common framework") Reported-by: Chris Wilson <[email protected]> Reviewed-by: Chris Wilson <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit 77c296966e866a795742a46fc52a218771894867) Signed-off-by: Rodrigo Vivi <[email protected]>
2020-11-16drm/i915/tgl: Fix Media power gate sequence.Rodrigo Vivi3-25/+22
Some media power gates are disabled by default. commit 5d86923060fc ("drm/i915/tgl: Enable VD HCP/MFX sub-pipe power gating") tried to enable it, but it duplicated an existent register. So, the main PG setup sequences ended up overwriting it. So, let's now merge this to the main PG setup sequence. v2: (Chris): s/BIT/REG_BIT, remove useless comment, remove useless =0, use the right gt, remove rc6 sequence doubt from commit message. Fixes: 5d86923060fc ("drm/i915/tgl: Enable VD HCP/MFX sub-pipe power gating") Cc: Lucas De Marchi <[email protected]> Cc: [email protected]#v5.5+ Cc: Dale B Stimson <[email protected]> Signed-off-by: Rodrigo Vivi <[email protected]> Cc: Chris Wilson <[email protected]> Reviewed-by: Chris Wilson <[email protected]> Signed-off-by: Chris Wilson <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit 695dc55b573985569259e18f8e6261a77924342b) Signed-off-by: Rodrigo Vivi <[email protected]>
2020-11-16Merge tag 'hyperv-fixes-signed' of ↵Linus Torvalds1-2/+6
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux Pull Hyper-V fix from Wei Liu: "One patch from Chris to fix kexec on Hyper-V" * tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: Drivers: hv: vmbus: Allow cleanup of VMBUS_CONNECT_CPU if disconnected
2020-11-16Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostLinus Torvalds5-117/+289
Pull vhost fixes from Michael Tsirkin: "Fixes all over the place, most notably vhost scsi IO error fixes" * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: vhost scsi: Add support for LUN resets. vhost scsi: add lun parser helper vhost scsi: fix cmd completion race vhost scsi: alloc cmds per vq instead of session vhost: add helper to check if a vq has been setup vdpasim: fix "mac_pton" undefined error swiotlb: using SIZE_MAX needs limits.h included
2020-11-16MAINTAINERS: update cxgb4 and cxgb3 maintainerRaju Rangoju1-3/+3
Update cxgb4 and cxgb3 driver maintainer Signed-off-by: Raju Rangoju <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16drm/amdgpu: remove experimental flag from arcturusAlex Deucher1-4/+4
This has been stable for a while. Reviewed-by: Hawking Zhang <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2020-11-16net: lantiq: Wait for the GPHY firmware to be readyMartin Blumenstingl1-0/+11
A user reports (slightly shortened from the original message): libphy: lantiq,xrx200-mdio: probed mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing. gswip 1e108000.switch lan: no phy at 2 gswip 1e108000.switch lan: failed to connect to port 2: -19 lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy This is a single-port board using the internal Fast Ethernet PHY. The user reports that switching to PHY scanning instead of configuring the PHY within device-tree works around this issue. The documentation for the standalone variant of the PHY11G (which is probably very similar to what is used inside the xRX200 SoCs but having the firmware burnt onto that standalone chip in the factory) states that the PHY needs 300ms to be ready for MDIO communication after releasing the reset. Add a 300ms delay after initializing all GPHYs to ensure that the GPHY firmware had enough time to initialize and to appear on the MDIO bus. Unfortunately there is no (known) documentation on what the minimum time to wait after releasing the reset on an internal PHY so play safe and take the one for the external variant. Only wait after the last GPHY firmware is loaded to not slow down the initialization too much ( xRX200 has two GPHYs but newer SoCs have at least three GPHYs). Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: Martin Blumenstingl <[email protected]> Acked-by: Hauke Mehrtens <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16selftests/bpf: Fix error return code in run_getsockopt_test()Wang Hai1-1/+2
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 65b4414a05eb ("selftests/bpf: add sockopt test that exercises BPF_F_ALLOW_MULTI") Reported-by: Hulk Robot <[email protected]> Signed-off-by: Wang Hai <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2020-11-16mm: never attempt async page lock if we've transferred data alreadyJens Axboe1-4/+14
We catch the case where we enter generic_file_buffered_read() with data already transferred, but we also need to be careful not to allow an async page lock if we're looping transferring data. If not, we could be returning -EIOCBQUEUED instead of the transferred amount, and it could result in double waitqueue additions as well. Cc: [email protected] # v5.9 Fixes: 1a0a7853b901 ("mm: support async buffered reads in generic_file_buffered_read()") Signed-off-by: Jens Axboe <[email protected]>
2020-11-16ASoC: Intel: catpt: Correct clock selection for dai triggerCezary Rojewski1-5/+2
During stream start DSP firmware requires LPCS disabled as that moment in time is resource heavy. Currently high-clock is selected on start of second stream onwards while low-clock is re-selected before stream actually leaves RESUME state i.e. PAUSE_STREAM call. Fix this by always updating clock before RESUME_STREAM and directly after PAUSE_STREAM. Fixes: a126750fc865 ("ASoC: Intel: catpt: PCM operations") Signed-off-by: Cezary Rojewski <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Mark Brown <[email protected]>
2020-11-16ASoC: Intel: catpt: Skip position update for unprepared streamsCezary Rojewski1-0/+2
Playing with very low period sizes may lead to timeouts when awaiting RESET_STREAM reply for offload streams. This is caused by NOTIFY_POSITION appearing in the middle of trigger(stop). Stream is unprepared during trigger(stop) where PAUSE_STREAM IPC gets invoked. However, all data that is already mixed in DSP firmware's mixer stream will still be played regardless of the pause. For offload streams, this means possibility for another NOTIFY_POSITION to process. Keep these notifications in check by only handling them when stream is in prepared state. Fixes: a126750fc865 ("ASoC: Intel: catpt: PCM operations") Signed-off-by: Cezary Rojewski <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Mark Brown <[email protected]>
2020-11-16spi: cadence-quadspi: Fix error return code in cqspi_probeZhihao Cheng1-0/+2
Fix to return the error code from devm_reset_control_get_optional_exclusive() instaed of 0 in cqspi_probe(). Fixes: 31fb632b5d43ca ("spi: Move cadence-quadspi driver to drivers/spi/") Reported-by: Hulk Robot <[email protected]> Signed-off-by: Zhihao Cheng <[email protected]> Reviewed-by: Philipp Zabel <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Mark Brown <[email protected]>
2020-11-16ASoC: qcom: lpass-platform: Fix memory leakSrinivasa Rao Mandadapu1-1/+4
lpass_pcm_data is not freed in error paths. Free it in error paths to avoid memory leak. Fixes: 022d00ee0b55 ("ASoC: lpass-platform: Fix broken pcm data usage") Signed-off-by: Pavel Machek <[email protected]> Signed-off-by: V Sujith Kumar Reddy <[email protected]> Signed-off-by: Srinivasa Rao Mandadapu <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Mark Brown <[email protected]>
2020-11-16ASoC: Intel: KMB: Fix S24_LE configurationMichael Sit Wei Hong1-3/+3
S24_LE is 24 bit audio in 32 bit container configuration Fixing the configuration to match the data arrangement of this audio format. Fixes: c5477e966728 ("ASoC: Intel: Add KeemBay platform driver") Signed-off-by: Michael Sit Wei Hong <[email protected]> Reviewed-by: Pierre-Louis Bossart <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Mark Brown <[email protected]>
2020-11-16drm/amd/display: Add missing pflip irq for dcn2.0Alex Deucher1-2/+2
If we have more than 4 displays we will run into dummy irq calls or flip timout issues. Reviewed-by: Nicholas Kazlauskas <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Cc: [email protected]
2020-11-16ACPI, APEI, Fix error return value in apei_map_generic_address()Aili Yao1-0/+4
From commit 6915564dc5a8 ("ACPI: OSL: Change the type of acpi_os_map_generic_address() return value"), acpi_os_map_generic_address() will return logical address or NULL for error, but for ACPI_ADR_SPACE_SYSTEM_IO case, it should be also return 0 as it's a normal case, but now it will return -ENXIO. So check it out for such case to avoid einj module initialization fail. Fixes: 6915564dc5a8 ("ACPI: OSL: Change the type of acpi_os_map_generic_address() return value") Cc: <[email protected]> Reviewed-by: James Morse <[email protected]> Tested-by: Tony Luck <[email protected]> Signed-off-by: Aili Yao <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2020-11-16MAINTAINERS: Add Martin Schiller as a maintainer for the X.25 stackXie He1-10/+9
Martin Schiller is an active developer and reviewer for the X.25 code. His company is providing products based on the Linux X.25 stack. So he is a good candidate for maintainers of the X.25 code. The original maintainer of the X.25 network layer (Andrew Hendry) has not sent any email to the netdev mail list since 2013. So he is probably inactive now. Cc: Andrew Hendry <[email protected]> Signed-off-by: Xie He <[email protected]> Acked-by: Martin Schiller <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16ipv6/netfilter: Discard first fragment not including all headersGeorg Kohmann3-20/+46
Packets are processed even though the first fragment don't include all headers through the upper layer header. This breaks TAHI IPv6 Core Conformance Test v6LC.1.3.6. Referring to RFC8200 SECTION 4.5: "If the first fragment does not include all headers through an Upper-Layer header, then that fragment should be discarded and an ICMP Parameter Problem, Code 3, message should be sent to the source of the fragment, with the Pointer field set to zero." The fragment needs to be validated the same way it is done in commit 2efdaaaf883a ("IPv6: reply ICMP error if the first fragment don't include all headers") for ipv6. Wrap the validation into a common function, ipv6_frag_thdr_truncated() to check for truncation in the upper layer header. This validation does not fullfill all aspects of RFC 8200, section 4.5, but is at the moment sufficient to pass mentioned TAHI test. In netfilter, utilize the fragment offset returned by find_prev_fhdr() to let ipv6_frag_thdr_truncated() start it's traverse from the fragment header. Return 0 to drop the fragment in the netfilter. This is the same behaviour as used on other protocol errors in this function, e.g. when nf_ct_frag6_queue() returns -EPROTO. The Fragment will later be picked up by ipv6_frag_rcv() in reassembly.c. ipv6_frag_rcv() will then send an appropriate ICMP Parameter Problem message back to the source. References commit 2efdaaaf883a ("IPv6: reply ICMP error if the first fragment don't include all headers") Signed-off-by: Georg Kohmann <[email protected]> Acked-by: Pablo Neira Ayuso <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16media: venus: pm_helpers: Fix kernel module reloadStanimir Varbanov1-2/+2
After initial kernel module load during kernel boot and removing the module and try to load it again an Unable to handle kernel paging request is observed: Unable to handle kernel paging request at virtual address ffffa44f7416eae0 Mem abort info: ESR = 0x96000047 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 Data abort info: ISV = 0, ISS = 0x00000047 CM = 0, WnR = 1 swapper pgtable: 4k pages, 48-bit VAs, pgdp=000000008147c000 [ffffa44f7416eae0] pgd=000000017df9f003, p4d=000000017df9f003, pud=000000017df9e003, pmd=000000017df9b003, pte=0000000000000000 Internal error: Oops: 96000047 [#1] PREEMPT SMP Modules linked in: venus_core(+) snd_soc_wsa881x regmap_sdw af_alg snd_soc_wcd934x soundwire_qcom gpio_wcd934x q6asm_dai q6routing q6adm q6afe_dai snd_soc_hdmi_codec q6afe q6asm q6dsp_common q6cor display_connector rmtfs_mem drm ip_tables x_tables ipv6 [last unloaded: venus_core] CPU: 6 PID: 889 Comm: modprobe Tainted: G W 5.10.0-rc1+ #8 Hardware name: Thundercomm Dragonboard 845c (DT) pstate: 80400085 (Nzcv daIf +PAN -UAO -TCO BTYPE=--) pc : queued_spin_lock_slowpath+0x1dc/0x3c8 lr : do_raw_spin_lock+0xc0/0x118 sp : ffff8000142cb7b0 x29: ffff8000142cb7b0 x28: 0000000000000013 x27: ffffa44f72de5690 x26: 0000000000000003 x25: ffff17c2d00f8080 x24: ffff17c2c0d78010 x23: ffff17c2c0d4f700 x22: ffff17c2d00f8080 x21: 0000000000000000 x20: ffffa44f74148000 x19: ffff17c2c0d4f8f8 x18: 0000000000000000 x17: 0000000000000000 x16: ffffa44f7342f158 x15: 0000000000000040 x14: ffffa44f746e8320 x13: 0000000000000228 x12: 0000000000000020 x11: 0000000000000000 x10: 00000000001c0000 x9 : 0000000000000000 x8 : ffff17c33d746ac0 x7 : ffff17c2c109b000 x6 : ffffa44f7416eac0 x5 : ffff17c33d746ac0 x4 : 0000000000000000 x3 : ffff17c2c0d4f8f8 x2 : ffffa44f7416eae0 x1 : ffffa44f7416eae0 x0 : ffff17c33d746ac8 Call trace: queued_spin_lock_slowpath+0x1dc/0x3c8 do_raw_spin_lock+0xc0/0x118 _raw_spin_lock_irqsave+0x80/0x14c __pm_runtime_resume+0x38/0xb8 device_link_add+0x3b8/0x5d0 core_get_v4+0x268/0x2d8 [venus_core] venus_probe+0x108/0x458 [venus_core] platform_drv_probe+0x54/0xa8 really_probe+0xe4/0x3b0 driver_probe_device+0x58/0xb8 device_driver_attach+0x74/0x80 __driver_attach+0x58/0xe8 bus_for_each_dev+0x70/0xc0 driver_attach+0x24/0x30 bus_add_driver+0x150/0x1f8 driver_register+0x64/0x120 __platform_driver_register+0x48/0x58 qcom_venus_driver_init+0x20/0x1000 [venus_core] do_one_initcall+0x84/0x458 do_init_module+0x58/0x208 load_module+0x1ec0/0x26a8 __do_sys_finit_module+0xb8/0xf8 __arm64_sys_finit_module+0x20/0x30 el0_svc_common.constprop.0+0x7c/0x1c0 do_el0_svc+0x24/0x90 el0_sync_handler+0x180/0x188 el0_sync+0x174/0x180 Code: 91002100 8b0200c2 f861d884 aa0203e1 (f8246828) ---[ end trace f1f687c15fd6b2ca ]--- note: modprobe[889] exited with preempt_count 1 After revisit the OPP part of the code I found that OPP pmdomain is detached with direct call to dev_pm_domain_detach instead of OPP wraper for detaching pmdomains with OPP table. Correct this by calling the OPP dev_pm_opp_detach_genpd. Fixes: 9a538b83612c ('media: venus: core: Add support for opp tables/perf voting') Signed-off-by: Stanimir Varbanov <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2020-11-16media: venus: venc: Fix setting of profile and levelStanimir Varbanov3-5/+55
The profile and level in op_set_ctrl was recently changed but during v4l2_ctrl_handler_setup profile and level control values are mangled. Fixes: 435c53c3698f ("media: venus: venc: Use helper to set profile and level") Signed-off-by: Stanimir Varbanov <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2020-11-16Merge branch 'fix-usage-counter-leak-by-adding-a-general-sync-ops'Jakub Kicinski2-7/+26
Zhang Qilong says: ==================== Fix usage counter leak by adding a general sync ops In many case, we need to check return value of pm_runtime_get_sync, but it brings a trouble to the usage counter processing. Many callers forget to decrease the usage counter when it failed, which could resulted in reference leak. It has been discussed a lot[0][1]. So we add a function to deal with the usage counter for better coding and view. Then, we replace pm_runtime_resume_and_get with it in fec_main.c to avoid it. [0] https://lkml.org/lkml/2020/6/14/88 [1] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139 ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16net: fec: Fix reference count leak in fec series opsZhang Qilong1-7/+5
pm_runtime_get_sync() will increment pm usage at first and it will resume the device later. If runtime of the device has error or device is in inaccessible state(or other error state), resume operation will fail. If we do not call put operation to decrease the reference, it will result in reference count leak. Moreover, this device cannot enter the idle state and always stay busy or other non-idle state later. So we fixed it by replacing it with pm_runtime_resume_and_get. Fixes: 8fff755e9f8d0 ("net: fec: Ensure clocks are enabled while using mdio bus") Signed-off-by: Zhang Qilong <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16PM: runtime: Add pm_runtime_resume_and_get to deal with usage counterZhang Qilong1-0/+21
In many case, we need to check return value of pm_runtime_get_sync, but it brings a trouble to the usage counter processing. Many callers forget to decrease the usage counter when it failed, which could resulted in reference leak. It has been discussed a lot[0][1]. So we add a function to deal with the usage counter for better coding. [0]https://lkml.org/lkml/2020/6/14/88 [1]https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139 Signed-off-by: Zhang Qilong <[email protected]> Acked-by: Rafael J. Wysocki <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16dmaengine: pl330: _prep_dma_memcpy: Fix wrong burst sizeSugar Zhang1-1/+1
Actually, burst size is equal to '1 << desc->rqcfg.brst_size'. we should use burst size, not desc->rqcfg.brst_size. dma memcpy performance on Rockchip RV1126 @ 1512MHz A7, 1056MHz LPDDR3, 200MHz DMA: dmatest: /# echo dma0chan0 > /sys/module/dmatest/parameters/channel /# echo 4194304 > /sys/module/dmatest/parameters/test_buf_size /# echo 8 > /sys/module/dmatest/parameters/iterations /# echo y > /sys/module/dmatest/parameters/norandom /# echo y > /sys/module/dmatest/parameters/verbose /# echo 1 > /sys/module/dmatest/parameters/run dmatest: dma0chan0-copy0: result #1: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000 dmatest: dma0chan0-copy0: result #2: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000 dmatest: dma0chan0-copy0: result #3: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000 dmatest: dma0chan0-copy0: result #4: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000 dmatest: dma0chan0-copy0: result #5: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000 dmatest: dma0chan0-copy0: result #6: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000 dmatest: dma0chan0-copy0: result #7: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000 dmatest: dma0chan0-copy0: result #8: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000 Before: dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 48 iops 200338 KB/s (0) After this patch: dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 179 iops 734873 KB/s (0) After this patch and increase dma clk to 400MHz: dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 259 iops 1062929 KB/s (0) Signed-off-by: Sugar Zhang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Vinod Koul <[email protected]>
2020-11-16dmaengine: ioatdma: remove unused function missed during dma_v2 removalLukas Bulwahn1-10/+0
Commit 7f832645d0e5 ("dmaengine: ioatdma: remove ioatdma v2 registration") missed to remove dca2_tag_map_valid() during its removal. Hence, since then, dca2_tag_map_valid() is unused and make CC=clang W=1 warns: drivers/dma/ioat/dca.c:44:19: warning: unused function 'dca2_tag_map_valid' [-Wunused-function] So, remove this unused function and get rid of a -Wused-function warning. Signed-off-by: Lukas Bulwahn <[email protected]> Reviewed-by: Nathan Chancellor <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Vinod Koul <[email protected]>
2020-11-16perf test: Avoid an msan warning in a copied stack.Ian Rogers1-0/+7
This fix is for a failure that occurred in the DWARF unwind perf test. Stack unwinders may probe memory when looking for frames. Memory sanitizer will poison and track uninitialized memory on the stack, and on the heap if the value is copied to the heap. This can lead to false memory sanitizer failures for the use of an uninitialized value. Avoid this problem by removing the poison on the copied stack. The full msan failure with track origins looks like: ==2168==WARNING: MemorySanitizer: use-of-uninitialized-value #0 0x559ceb10755b in handle_cfi elfutils/libdwfl/frame_unwind.c:648:8 #1 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4 #2 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7 #3 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10 #4 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17 #5 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17 #6 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14 #7 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10 #8 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8 #9 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8 #10 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26 #11 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0) #12 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2 #13 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9 #14 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9 #15 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8 #16 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9 #17 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9 #18 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4 #19 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9 #20 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11 #21 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8 #22 0x559cea95fbce in run_argv tools/perf/perf.c:409:2 #23 0x559cea95fbce in main tools/perf/perf.c:539:3 Uninitialized value was stored to memory at #0 0x559ceb106acf in __libdwfl_frame_reg_set elfutils/libdwfl/frame_unwind.c:77:22 #1 0x559ceb106acf in handle_cfi elfutils/libdwfl/frame_unwind.c:627:13 #2 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4 #3 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7 #4 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10 #5 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17 #6 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17 #7 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14 #8 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10 #9 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8 #10 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8 #11 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26 #12 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0) #13 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2 #14 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9 #15 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9 #16 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8 #17 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9 #18 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9 #19 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4 #20 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9 #21 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11 #22 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8 #23 0x559cea95fbce in run_argv tools/perf/perf.c:409:2 #24 0x559cea95fbce in main tools/perf/perf.c:539:3 Uninitialized value was stored to memory at #0 0x559ceb106a54 in handle_cfi elfutils/libdwfl/frame_unwind.c:613:9 #1 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4 #2 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7 #3 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10 #4 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17 #5 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17 #6 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14 #7 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10 #8 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8 #9 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8 #10 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26 #11 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0) #12 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2 #13 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9 #14 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9 #15 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8 #16 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9 #17 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9 #18 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4 #19 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9 #20 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11 #21 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8 #22 0x559cea95fbce in run_argv tools/perf/perf.c:409:2 #23 0x559cea95fbce in main tools/perf/perf.c:539:3 Uninitialized value was stored to memory at #0 0x559ceaff8800 in memory_read tools/perf/util/unwind-libdw.c:156:10 #1 0x559ceb10f053 in expr_eval elfutils/libdwfl/frame_unwind.c:501:13 #2 0x559ceb1060cc in handle_cfi elfutils/libdwfl/frame_unwind.c:603:18 #3 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4 #4 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7 #5 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10 #6 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17 #7 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17 #8 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14 #9 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10 #10 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8 #11 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8 #12 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26 #13 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0) #14 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2 #15 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9 #16 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9 #17 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8 #18 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9 #19 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9 #20 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4 #21 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9 #22 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11 #23 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8 #24 0x559cea95fbce in run_argv tools/perf/perf.c:409:2 #25 0x559cea95fbce in main tools/perf/perf.c:539:3 Uninitialized value was stored to memory at #0 0x559cea9027d9 in __msan_memcpy llvm/llvm-project/compiler-rt/lib/msan/msan_interceptors.cpp:1558:3 #1 0x559cea9d2185 in sample_ustack tools/perf/arch/x86/tests/dwarf-unwind.c:41:2 #2 0x559cea9d202c in test__arch_unwind_sample tools/perf/arch/x86/tests/dwarf-unwind.c:72:9 #3 0x559ceabc9cbd in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:106:6 #4 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26 #5 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0) #6 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2 #7 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9 #8 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9 #9 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8 #10 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9 #11 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9 #12 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4 #13 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9 #14 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11 #15 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8 #16 0x559cea95fbce in run_argv tools/perf/perf.c:409:2 #17 0x559cea95fbce in main tools/perf/perf.c:539:3 Uninitialized value was created by an allocation of 'bf' in the stack frame of function 'perf_event__synthesize_mmap_events' #0 0x559ceafc5f60 in perf_event__synthesize_mmap_events tools/perf/util/synthetic-events.c:445 SUMMARY: MemorySanitizer: use-of-uninitialized-value elfutils/libdwfl/frame_unwind.c:648:8 in handle_cfi Signed-off-by: Ian Rogers <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: [email protected] Cc: Jiri Olsa <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Sandeep Dasgupta <[email protected]> Cc: Stephane Eranian <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-11-16dmaengine: idxd: fix mapping of portal sizeDave Jiang3-3/+3
Portal size is 4k. Current code is mapping all 4 portals in a single chunk. Restrict the mapped portal size to a single portal to ensure that submission only goes to the intended portal address. Fixes: c52ca478233c ("dmaengine: idxd: add configuration component of driver") Signed-off-by: Dave Jiang <[email protected]> Link: https://lore.kernel.org/r/160513342642.510187.16450549281618747065.stgit@djiang5-desk3.ch.intel.com Signed-off-by: Vinod Koul <[email protected]>
2020-11-16perf inject: Fix file corruption due to event deletionAl Grant1-11/+1
"perf inject" can create corrupt files when synthesizing sample events from AUX data. This happens when in the input file, the first event (for the AUX data) has a different sample_type from the second event (generally dummy). Specifically, they differ in the bits that indicate the standard fields appended to perf records in the mmap buffer. "perf inject" deletes the first event and moves up the second event to first position. The problem is with the synthetic PERF_RECORD_MMAP (etc.) events created by "perf record". Since these are synthetic versions of events which are normally produced by the kernel, they have to have the standard fields appended as described by sample_type. "perf record" fills these in with zeroes, including the IDENTIFIER field; perf readers interpret records with zero IDENTIFIER using the descriptor for the first event in the file. Since "perf inject" changes the first event, these synthetic records are then processed with the wrong value of sample_type, and the perf reader reads bad data, reports on incorrect length records etc. Mismatching sample_types are seen with "perf record -e cs_etm//", where the AUX event has TID|TIME|CPU|IDENTIFIER and the dummy event has TID|TIME|IDENTIFIER. Perhaps they could be the same, but it isn't normally a problem if they aren't - perf has no problems reading the file. The sample_types have to agree on the position of IDENTIFIER, because that's how perf finds the right event descriptor in the first place, but they don't normally have to agree on other fields, and perf doesn't check that they do. The problem is specific to the way "perf inject" reorganizes the events and the way synthetic MMAP events are recorded with a zero identifier. A simple solution is to stop "perf inject" deleting the tracing event. Committer testing Removed the now unused 'evsel' variable, update the comment about the evsel removal not being performed anymore, and apply the patch manually as it failed with this warning: warning: Patch sent with format=flowed; space at the end of lines might be lost. Testing it with: $ perf bench internals inject-build-id # Running 'internals/inject-build-id' benchmark: Average build-id injection took: 8.543 msec (+- 0.130 msec) Average time per event: 0.838 usec (+- 0.013 usec) Average memory usage: 12717 KB (+- 9 KB) Average build-id-all injection took: 5.710 msec (+- 0.058 msec) Average time per event: 0.560 usec (+- 0.006 usec) Average memory usage: 12079 KB (+- 7 KB) $ Signed-off-by: Al Grant <[email protected]> Acked-by: Adrian Hunter <[email protected]> Acked-by: Namhyung Kim <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Peter Zijlstra <[email protected]> LPU-Reference: [email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2020-11-16Merge tag 'imx-fixes-5.10-4' of ↵Arnd Bergmann4-3/+6
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 5.10, round 4: - Fix MDIO over clocking on vf610-zii-dev-rev-b board to get switch device work reliably. - Fix imx50-evk IOMUX for the chip select 1 to use GPIO4_13 instead of the native CSPI_SSI function. - Fix voltage for 1.6GHz CPU operating point on i.MX8MM to match hardware datasheet. - Fix phy-mode for KSZ9031 PHY on imx6qdl-udoo board. * tag 'imx-fixes-5.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: dts: imx50-evk: Fix the chip select 1 IOMUX arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy Link: https://lore.kernel.org/r/20201116090702.GM5849@dragon Signed-off-by: Arnd Bergmann <[email protected]>
2020-11-16Merge tag 'renesas-fixes-for-v5.10-tag1' of ↵Arnd Bergmann1-0/+6
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes Renesas fixes for v5.10 - Add missing audio clock on RZ/G2H. * tag 'renesas-fixes-for-v5.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: arm64: dts: renesas: r8a774e1: Add missing audio_clk_b Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnd Bergmann <[email protected]>
2020-11-16Merge tag 'linux-can-fixes-for-5.10-20201115' of ↵Jakub Kicinski11-46/+100
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2020-11-15 Anant Thazhemadam contributed two patches for the AF_CAN that prevent potential access of uninitialized member in can_rcv() and canfd_rcv(). The next patch is by Alejandro Concepcion Rodriguez and changes can_restart() to use the correct function to push a skb into the networking stack from process context. Zhang Qilong's patch fixes a memory leak in the error path of the ti_hecc's probe function. A patch by me fixes mcba_usb_start_xmit() function in the mcba_usb driver, to first fill the skb and then pass it to can_put_echo_skb(). Colin Ian King's patch fixes a potential integer overflow on shift in the peak_usb driver. The next two patches target the flexcan driver, a patch by me adds the missing "req_bit" to the stop mode property comment (which was broken during net-next for v5.10). Zhang Qilong's patch fixes the failure handling of pm_runtime_get_sync(). The next seven patches target the m_can driver including the tcan4x5x spi driver glue code. Enric Balletbo i Serra's patch for the tcan4x5x Kconfig fix the REGMAP_SPI dependency handling. A patch by me for the tcan4x5x driver's probe() function adds missing error handling to for devm_regmap_init(), and in tcan4x5x_can_remove() the order of deregistration is fixed. Wu Bo's patch for the m_can driver fixes the state change handling in m_can_handle_state_change(). Two patches by Dan Murphy first introduce m_can_class_free_dev() and then make use of it to fix the freeing of the can device. A patch by Faiz Abbas add a missing shutdown of the CAN controller in the m_can_stop() function. * tag 'linux-can-fixes-for-5.10-20201115' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can: can: m_can: m_can_stop(): set device to software init mode before closing can: m_can: Fix freeing of can device from peripherials can: m_can: m_can_class_free_dev(): introduce new function can: m_can: m_can_handle_state_change(): fix state change can: tcan4x5x: tcan4x5x_can_remove(): fix order of deregistration can: tcan4x5x: tcan4x5x_can_probe(): add missing error checking for devm_regmap_init() can: tcan4x5x: replace depends on REGMAP_SPI with depends on SPI can: flexcan: fix failure handling of pm_runtime_get_sync() can: flexcan: flexcan_setup_stop_mode(): add missing "req_bit" to stop mode property comment can: peak_usb: fix potential integer overflow on shift of a int can: mcba_usb: mcba_usb_start_xmit(): first fill skb, then pass to can_put_echo_skb() can: ti_hecc: Fix memleak in ti_hecc_probe can: dev: can_restart(): post buffer from the right context can: af_can: prevent potential access of uninitialized member in canfd_rcv() can: af_can: prevent potential access of uninitialized member in can_rcv() ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-11-16s390/dasd: fix null pointer dereference for ERP requestsStefan Haberland1-0/+6
When requeueing all requests on the device request queue to the blocklayer we might get to an ERP (error recovery) request that is a copy of an original CQR. Those requests do not have blocklayer request information or a pointer to the dasd_queue set. When trying to access those data it will lead to a null pointer dereference in dasd_requeue_all_requests(). Fix by checking if the request is an ERP request that can simply be ignored. The blocklayer request will be requeued by the original CQR that is on the device queue right behind the ERP request. Fixes: 9487cfd3430d ("s390/dasd: fix handling of internal requests") Cc: <[email protected]> #4.16 Signed-off-by: Stefan Haberland <[email protected]> Reviewed-by: Jan Hoeppner <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2020-11-16ALSA: hda: Add Alderlake-S PCI ID and HDMI codec vidKai Vehmanen2-0/+4
Add HD Audio PCI ID and HDMI codec vendor ID for Intel Alder Lake. Signed-off-by: Kai Vehmanen <[email protected]> Reviewed-by: Pierre-Louis Bossart <[email protected]> Reviewed-by: Guennadi Liakhovetski <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2020-11-16ACPI: fan: Initialize performance state sysfs attributeGuenter Roeck1-0/+1
The following warning is reported if lock debugging is enabled. DEBUG_LOCKS_WARN_ON(1) WARNING: CPU: 1 PID: 1 at kernel/locking/lockdep.c:4617 lockdep_init_map_waits+0x141/0x222 ... Call Trace: __kernfs_create_file+0x7a/0xd8 sysfs_add_file_mode_ns+0x135/0x189 sysfs_create_file_ns+0x70/0xa0 acpi_fan_probe+0x547/0x621 platform_drv_probe+0x67/0x8b ... Dynamically allocated sysfs attributes need to be initialized to avoid the warning. Fixes: d19e470b6605 ("ACPI: fan: Expose fan performance state information") Signed-off-by: Guenter Roeck <[email protected]> Cc: 5.6+ <[email protected]> # 5.6+ Signed-off-by: Rafael J. Wysocki <[email protected]>
2020-11-16iommu/vt-d: Take CONFIG_PCI_ATS into accountThomas Gleixner1-0/+2
pci_dev::physfn is only available when CONFIG_PCI_ATS is set. The recent fix for the irqdomain rework missed that dependency which makes the build fail when CONFIG_PCI_ATS=n. Add the necessary #ifdeffery. Reported-by: Geert Uytterhoeven <[email protected]> Fixes: ff828729be44 ("iommu/vt-d: Cure VF irqdomain hickup") Signed-off-by: Thomas Gleixner <[email protected]> Cc: Joerg Roedel <[email protected]>