| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling
into usb_sg_cancel(). usb_sg_cancel() will do nothing and return
directly if req->status has been set to a non-zero value. This will
cause driver hang whenever transfer time out is triggered.
This patch fixes this issue. It could be backported to stable kernel
with version later than v3.15.
Cc: [email protected] # 3.15+
Cc: Alan Stern <[email protected]>
Signed-off-by: Lu Baolu <[email protected]>
Suggested-by: Alan Stern <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.8-rc1
First set of fixes for v4.8-rc cycle. Again, dwc3 is
the most active driver with over 60% of this pull
request touching it.
The most important fixes are related to scatterlist
usage with dwc3. Before this pull request, we were
increment request->actual multiple times and this
would result in request->actual being larger than
request->length.
Also, if a we received a short packet midway through
processing a scatterlist, we were not clearning HWO
bit as we should.
Other than the large dwc3 scatterlist fixes, we have
a new Device ID for Intel's Kabylake silicon.
Other drivers, such as fsl_qe_udc and renesas udc,
also got a few minor fixes. Details are in shortlog.
|
|
stop consuming TRBs when we reach one with HWO bit
already set. This will prevent us from prematurely
retiring a TRB.
Signed-off-by: Felipe Balbi <[email protected]>
|
|
According to Synopsys Databook 2.60a, section 8.3.4,
it's stated that:
The LST bit should be set to 0 (isochronous
transfers normally continue until the
endpoint is removed entirely, at which time
an End Transfer command is used to stop the
transfer).
This patch makes sure that detail is observed and
fixes a regression with Android Audio playback
caused by recent changes to DWC3 gadget.
Signed-off-by: Janusz Dziedzic <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
When rndis data transfer is in progress, some Windows7 Host PC is not
sending the GET_ENCAPSULATED_RESPONSE command for receiving the response
for the previous SEND_ENCAPSULATED_COMMAND processed.
The rndis function driver appends each response for the
SEND_ENCAPSULATED_COMMAND in a queue. As the above process got corrupted,
the Host sends a REMOTE_NDIS_RESET_MSG command to do a soft-reset.
As the rndis response queue is not freed, the previous response is sent
as a part of this REMOTE_NDIS_RESET_MSG's reset response and the Host
block any more Rndis transfers.
Hence free the rndis response queue as a part of this soft-reset so that
the correct response for REMOTE_NDIS_RESET_MSG is sent properly during the
response command.
Signed-off-by: Rajkumar Raghupathy <[email protected]>
Signed-off-by: Xerox Lin <[email protected]>
[AmitP: Cherry-picked this patch and folded other relevant
fixes from Android common kernel android-4.4]
Signed-off-by: Amit Pundir <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
The udc device needs to be deleted if error occurs
Fixes: 855ed04a3758 ("usb: gadget: udc-core: independent registration of
gadgets and gadget drivers")
Signed-off-by: Peter Chen <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
The udc->eps[] array has USB_MAX_ENDPOINTS elements so > should be >=.
Fixes: 3948f0e0c999 ('usb: add Freescale QE/CPM USB peripheral controller driver')
Acked-by: Peter Chen <[email protected]>
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
Fix io submissions failing with ENODEV.
Signed-off-by: Mathieu Laurendeau <[email protected]>
Fixes: 7fe3976e0f3a ("gadget: switch ep_io_operations to ->read_iter/->write_iter")
Signed-off-by: Felipe Balbi <[email protected]>
|
|
In 'composite_os_desc_req_prepare', if one of the memory allocations fail,
0 will be returned, which means success.
We should return -ENOMEM instead.
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
If this memory allocation fail, we will return 0, which means success.
Return -ENOMEM instead.
Reviewed-by: Laurent Pinchart <[email protected]>
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
When reading synchronously from a non-zero endpoint, gadgetfs will
return -EFAULT even if the read succeeds, due to a bad check of the
copy_to_iter() return value.
This fix compares the return value of copy_to_iter to the amount of
bytes that was passed, and only fails if they are not the same.
Signed-off-by: Binyamin Sharet <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
For case 14 and case 21, their correct return value is the number
of bytes transferred, so it is a positive integer. But in usbtest_ioctl,
it takes non-zero as false return value for usbtest_do_ioctl, so
it will treat the correct test as wrong test, then the time on
tests will be the minus value.
Signed-off-by: Peter Chen <[email protected]>
Cc: stable <[email protected]>
Fixes: 18fc4ebdc705 ("usb: misc: usbtest: Remove timeval usage")
Signed-off-by: Felipe Balbi <[email protected]>
|
|
Add missing platform_set_drvdata() in dwc3_of_simple_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
Add missing platform_set_drvdata() in omap_otg_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
There may be a race condition if f_fs calls unregister_gadget_item in
ffs_closed() when unregister_gadget is called by UDC store at the same time.
this leads to a kernel NULL pointer dereference:
[ 310.644928] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 310.645053] init: Service 'adbd' is being killed...
[ 310.658938] pgd = c9528000
[ 310.662515] [00000004] *pgd=19451831, *pte=00000000, *ppte=00000000
[ 310.669702] Internal error: Oops: 817 [#1] PREEMPT SMP ARM
[ 310.675211] Modules linked in:
[ 310.678294] CPU: 0 PID: 1537 Comm: ->transport Not tainted 4.1.15-03725-g793404c #2
[ 310.685958] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 310.692493] task: c8e24200 ti: c945e000 task.ti: c945e000
[ 310.697911] PC is at usb_gadget_unregister_driver+0xb4/0xd0
[ 310.703502] LR is at __mutex_lock_slowpath+0x10c/0x16c
[ 310.708648] pc : [<c075efc0>] lr : [<c0bfb0bc>] psr: 600f0113
<snip..>
[ 311.565585] [<c075efc0>] (usb_gadget_unregister_driver) from [<c075e2b8>] (unregister_gadget_item+0x1c/0x34)
[ 311.575426] [<c075e2b8>] (unregister_gadget_item) from [<c076fcc8>] (ffs_closed+0x8c/0x9c)
[ 311.583702] [<c076fcc8>] (ffs_closed) from [<c07736b8>] (ffs_data_reset+0xc/0xa0)
[ 311.591194] [<c07736b8>] (ffs_data_reset) from [<c07738ac>] (ffs_data_closed+0x90/0xd0)
[ 311.599208] [<c07738ac>] (ffs_data_closed) from [<c07738f8>] (ffs_ep0_release+0xc/0x14)
[ 311.607224] [<c07738f8>] (ffs_ep0_release) from [<c023e030>] (__fput+0x80/0x1d0)
[ 311.614635] [<c023e030>] (__fput) from [<c014e688>] (task_work_run+0xb0/0xe8)
[ 311.621788] [<c014e688>] (task_work_run) from [<c010afdc>] (do_work_pending+0x7c/0xa4)
[ 311.629718] [<c010afdc>] (do_work_pending) from [<c010770c>] (work_pending+0xc/0x20)
for functions using functionFS, i.e. android adbd will close /dev/usb-ffs/adb/ep0
when usb IO thread fails, but switch adb from on to off also triggers write
"none" > UDC. These 2 operations both call unregister_gadget, which will lead
to the panic above.
add a mutex before calling unregister_gadget for api used in f_fs.
Signed-off-by: Winter Wang <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
dev->port_usb is checked for null pointer at above code, so dev->port_usb
might be null, fix it by adding null pointer check.
Signed-off-by: Peter Chen <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
cdev->config is checked for null pointer at above code, so cdev->config
might be null, fix it by adding null pointer check.
Signed-off-by: Peter Chen <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
This patch fixes an issue that isochronous transfer's data is possible to
be lost as a workaround. Since this driver uses a workqueue to start
the dmac, the transfer is possible to be delayed when system load is high.
Fixes: 6e4b74e4690d ("usb: renesas: fix scheduling in atomic context bug")
Cc: <[email protected]> # v3.4+
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
This patch fixes an issue that unexpected BRDY interruption happens
when the usb_ep_{enable,disable}() are called with different direction.
In this case, the driver will cause the following message:
renesas_usbhs e6590000.usb: irq_ready run_error 1 : -16
This issue causes the followings:
1) A pipe is enabled as transmission
2) The pipe sent a data
3) The pipe is disabled and re-enabled as reception.
4) The pipe got a queue
Since the driver doesn't clear the BRDYSTS flags after 2) above, the issue
happens. If we add such clearing the flags into the driver, the code will
become complicate. So, this patch clears the BRDYSTS flag of reception in
usbhsg_ep_enable() to avoid complicate.
Cc: <[email protected]> # v4.1+ (usbhs_xxxsts_clear() is needed)
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
Since R-Car Gen3 SoC has the USB-DMAC, this driver should set
dparam->has_usb_dmac to 1. Otherwise, behavior of this driver and
the usb-dmac driver will be mismatch, then sometimes receiving data will
be corrupt.
Fixes: de18757e272d ("usb: renesas_usbhs: add R-Car Gen3 power control")
Cc: <[email protected]> # v4.5+
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
Intel Kabylake PCH has the same DWC3 than Intel
Sunrisepoint. Add the new ID to the supported devices.
Cc: <[email protected]>
Signed-off-by: Heikki Krogerus <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
If we stop earlier due to short packet, we will
not be able to giveback all TRBs.
Cc: <[email protected]>
Cc: Brian E Rogers <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
DWC3 has one interesting peculiarity with chained
transfers. If we setup N chained transfers and we
get a short packet before processing all N TRBs,
DWC3 will (conditionally) issue a XferComplete or
XferInProgress event and retire all TRBs from the
one which got a short packet to the last without
clearing their HWO bits.
This means SW must clear HWO bit manually, which
this patch is doing.
Cc: <[email protected]>
Cc: Brian E Rogers <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
When using SG lists, we would end up setting
request->actual to:
num_mapped_sgs * (request->length - count)
Let's fix that up by incrementing request->actual
only once.
Cc: <[email protected]>
Reported-by: Brian E Rogers <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
GPIO control register is divided into IOPINS1 and IOPINS2.
And low 4-bit of register is controls output.
So, this patch fixes wrong mask of GPIO output.
Signed-off-by: Jaewon Kim <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Hans de Goede has reported a difficulty in the Linux port of libusb.
When a device is removed, the poll() system call in usbfs starts
returning POLLERR as soon as udev->state is set to
USB_STATE_NOTATTACHED, but the outstanding URBs are not available for
reaping until some time later (after usbdev_remove() has been called).
This is awkward for libusb or other usbfs clients, although not an
insuperable problem.
At any rate, it's easy to change usbfs so that it returns POLLHUP as
soon as the state becomes USB_STATE_NOTATTACHED but it doesn't return
POLLERR until after the outstanding URBs have completed. That's what
this patch does; it uses the fact that ps->list is always on the
dev->filelist list until usbdev_remove() takes it off, which happens
after all the outstanding URBs have been cancelled.
Signed-off-by: Alan Stern <[email protected]>
Reported-by: Hans de Goede <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
usbdev_mmap allocates a buffer. The size of the buffer is determined
by a user. So with this code (no need to be root):
int fd = open("/dev/bus/usb/001/001", O_RDONLY);
mmap(NULL, 0x800000, PROT_READ, MAP_SHARED, fd, 0);
we can see a warning:
WARNING: CPU: 0 PID: 21771 at ../mm/page_alloc.c:3563 __alloc_pages_slowpath+0x1036/0x16e0()
...
Call Trace:
[<ffffffff8117a3ae>] ? warn_slowpath_null+0x2e/0x40
[<ffffffff815178b6>] ? __alloc_pages_slowpath+0x1036/0x16e0
[<ffffffff81516880>] ? warn_alloc_failed+0x250/0x250
[<ffffffff8151226b>] ? get_page_from_freelist+0x75b/0x28b0
[<ffffffff815184e3>] ? __alloc_pages_nodemask+0x583/0x6b0
[<ffffffff81517f60>] ? __alloc_pages_slowpath+0x16e0/0x16e0
[<ffffffff810565d4>] ? dma_generic_alloc_coherent+0x104/0x220
[<ffffffffa0269e56>] ? hcd_buffer_alloc+0x1d6/0x3e0 [usbcore]
[<ffffffffa0269c80>] ? hcd_buffer_destroy+0xa0/0xa0 [usbcore]
[<ffffffffa0228f05>] ? usb_alloc_coherent+0x65/0x90 [usbcore]
[<ffffffffa0275c05>] ? usbdev_mmap+0x1a5/0x770 [usbcore]
...
Allocations like this one should be marked as __GFP_NOWARN. So do so.
The size could be also clipped by something like:
if (size >= (1 << (MAX_ORDER + PAGE_SHIFT - 1)))
return -ENOMEM;
But I think the overall limit of 16M (by usbfs_increase_memory_usage)
is enough, so that we only silence the warning here.
Signed-off-by: Jiri Slaby <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Alan Stern <[email protected]>
Cc: Steinar H. Gunderson <[email protected]>
Cc: Markus Rechberger <[email protected]>
Fixes: f7d34b445a (USB: Add support for usbfs zerocopy.)
Cc: 4.6+ <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In ehci_turn_off_all_ports() all EHCI port registers are cleared to zero.
On some hardware, this can lead to an system hang,
when ehci_port_power() accesses the already cleared registers.
This patch changes the order of cleanup.
First call ehci_port_power() which respects the current bits in
port status registers
and afterwards cleanup the hard way by setting everything to zero.
Signed-off-by: Marc Ohlf <[email protected]>
Acked-by: Alan Stern <[email protected]>
CC: <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Erroneous or malicious endpoint descriptors may have non-zero bits in
reserved positions, or out-of-bounds values. This patch helps prevent
these from causing problems by bounds-checking the wMaxPacketValue
entries in endpoint descriptors and capping the values at the maximum
allowed.
This issue was first discovered and tests were conducted by Jake Lamberson
<[email protected]>, an intern working for Rosie Hall.
Signed-off-by: Alan Stern <[email protected]>
Reported-by: roswest <[email protected]>
Tested-by: roswest <[email protected]>
CC: <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch fixes fives off-by-one bugs in the ftdi-elan driver code. The
bug can be triggered by plugging a USB adapter for CardBus 3G cards (model
U132 manufactured by Elan Digital Systems, Ltd), causing a kernel panic.
The fix was tested on Ubuntu 14.04.4 with 4.7.0-rc14.2.0-27-generic+ and
4.4.0-22-generic+ kernel. In the ftdi_elan_synchronize function, an
off-by-one memory corruption occurs when packet_bytes is equal or bigger
than m. After having read m bytes, that is bytes_read is equal to m, "
..\x00" is still copied to the stack variable causing an out bounds write
of 4 bytes, which overwrites the stack canary and results in a kernel
panic.
This off-by-one requires physical access to the machine. It is not
exploitable since we have no control on the overwritten data. Similar
off-by-one bugs have been observed in 4 other functions:
ftdi_elan_stuck_waiting, ftdi_elan_read, ftdi_elan_edset_output and
ftdi_elan_flush_input_fifo.
Reported-by: Alex Palesandro <[email protected]>
Signed-off-by: Xiao Han <[email protected]>
Tested-by: Paul Chaignon <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
For case 14 and case 21, their correct return value is the number
of bytes transferred, so it is a positive integer. But in usbtest_ioctl,
it takes non-zero as false return value for usbtest_do_ioctl, so
it will treat the correct test as wrong test, then the time on
tests will be the minus value.
Signed-off-by: Peter Chen <[email protected]>
Cc: stable <[email protected]>
Fixes: 18fc4ebdc705 ("usb: misc: usbtest: Remove timeval usage")
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The locking in hub_activate() is not adequate to provide full mutual
exclusion with hub_quiesce(). The subroutine locks the hub's
usb_interface, but the callers of hub_quiesce() (such as
hub_pre_reset() and hub_event()) hold the lock to the hub's
usb_device.
This patch changes hub_activate() to make it acquire the same lock as
those other routines.
Signed-off-by: Alan Stern <[email protected]>
CC: <[email protected]> #4.4+
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The early-exit pathway in hub_activate, added by commit e50293ef9775
("USB: fix invalid memory access in hub_activate()") needs
improvement. It duplicates code that is already present at the end of
the subroutine, and it neglects to undo the effect of a
usb_autopm_get_interface_no_resume() call.
This patch fixes both problems by making the early-exit pathway jump
directly to the end of the subroutine. It simplifies the code at the
end by merging two conditionals that actually test the same condition
although they appear different: If type < HUB_INIT3 then type must be
either HUB_INIT2 or HUB_INIT, and it can't be HUB_INIT because in that
case the subroutine would have exited earlier.
Signed-off-by: Alan Stern <[email protected]>
CC: <[email protected]> #4.4+
Reviewed-by: Viresh Kumar <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Memory leak and unbalanced reference count:
If the hub gets disconnected while the core is still activating it, this
can result in leaking memory of few USB structures.
This will happen if we have done a kref_get() from hub_activate() and
scheduled a delayed work item for HUB_INIT2/3. Now if hub_disconnect()
gets called before the delayed work expires, then we will cancel the
work from hub_quiesce(), but wouldn't do a kref_put(). And so the
unbalance.
kmemleak reports this as (with the commit e50293ef9775 backported to
3.10 kernel with other changes, though the same is true for mainline as
well):
unreferenced object 0xffffffc08af5b800 (size 1024):
comm "khubd", pid 73, jiffies 4295051211 (age 6482.350s)
hex dump (first 32 bytes):
30 68 f3 8c c0 ff ff ff 00 a0 b2 2e c0 ff ff ff 0h..............
01 00 00 00 00 00 00 00 00 94 7d 40 c0 ff ff ff ..........}@....
backtrace:
[<ffffffc0003079ec>] create_object+0x148/0x2a0
[<ffffffc000cc150c>] kmemleak_alloc+0x80/0xbc
[<ffffffc000303a7c>] kmem_cache_alloc_trace+0x120/0x1ac
[<ffffffc0006fa610>] hub_probe+0x120/0xb84
[<ffffffc000702b20>] usb_probe_interface+0x1ec/0x298
[<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
[<ffffffc0005d5308>] __device_attach+0x28/0x4c
[<ffffffc0005d3164>] bus_for_each_drv+0x78/0xac
[<ffffffc0005d4ee0>] device_attach+0x6c/0x9c
[<ffffffc0005d42b8>] bus_probe_device+0x28/0xa0
[<ffffffc0005d23a4>] device_add+0x324/0x604
[<ffffffc000700fcc>] usb_set_configuration+0x660/0x6cc
[<ffffffc00070a350>] generic_probe+0x44/0x84
[<ffffffc000702914>] usb_probe_device+0x54/0x74
[<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
[<ffffffc0005d5308>] __device_attach+0x28/0x4c
Deadlocks:
If the hub gets disconnected early enough (i.e. before INIT2/INIT3 are
finished and the init_work is still queued), the core may call
hub_quiesce() after acquiring interface device locks and it will wait
for the work to be cancelled synchronously. But if the work handler is
already running in parallel, it may try to acquire the same interface
device lock and this may result in deadlock.
Fix both the issues by removing the call to cancel_delayed_work_sync().
CC: <[email protected]> #4.4+
Fixes: e50293ef9775 ("USB: fix invalid memory access in hub_activate()")
Reported-by: Manu Gautam <[email protected]>
Signed-off-by: Viresh Kumar <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
|
|
Pull more block fixes from Jens Axboe:
"As mentioned in the pull the other day, a few more fixes for this
round, all related to the bio op changes in this series.
Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf. I
wanted to do that change right after or right before -rc1, so that
risk of conflict was reduced. I just rebased the series on top of
current master, and no new ->bi_rw usage has snuck in"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: rename bio bi_rw to bi_opf
target: iblock_execute_sync_cache() should use bio_set_op_attrs()
mm: make __swap_writepage() use bio_set_op_attrs()
block/mm: make bdev_ops->rw_page() take a bool for read/write
|
|
Pull drm zpos property support from Dave Airlie:
"This tree was waiting on some media stuff I hadn't had time to get a
stable branchpoint off, so I just waited until it was all in your tree
first.
It's been around a bit on the list and shouldn't affect anything
outside adding the generic API and moving some ARM drivers to using
it"
* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
drm: rcar: use generic code for managing zpos plane property
drm/exynos: use generic code for managing zpos plane property
drm: sti: use generic zpos for plane
drm: add generic zpos property
|
|
Since commit 63a4cc24867d, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <[email protected]>
|
|
The original commit missed this function, it needs to mark it a
write flush.
Cc: Mike Christie <[email protected]>
Fixes: e742fc32fcb4 ("target: use bio op accessors")
Signed-off-by: Jens Axboe <[email protected]>
|
|
Cleaner than manipulating bio->bi_rw flags directly.
Signed-off-by: Jens Axboe <[email protected]>
|
|
Commit abf545484d31 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Pull documentation fixes from Jonathan Corbet:
"Three fixes for the docs build, including removing an annoying warning
on 'make help' if sphinx isn't present"
* tag 'doc-4.8-fixes' of git://git.lwn.net/linux:
DocBook: use DOCBOOKS="" to ignore DocBooks instead of IGNORE_DOCBOOKS=1
Documenation: update cgroup's document path
Documentation/sphinx: do not warn about missing tools in 'make help'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc
Pull binfmt_misc update from James Bottomley:
"This update is to allow architecture emulation containers to function
such that the emulation binary can be housed outside the container
itself. The container and fs parts both have acks from relevant
experts.
To use the new feature you have to add an F option to your binfmt_misc
configuration"
From the docs:
"The usual behaviour of binfmt_misc is to spawn the binary lazily when
the misc format file is invoked. However, this doesn't work very well
in the face of mount namespaces and changeroots, so the F mode opens
the binary as soon as the emulation is installed and uses the opened
image to spawn the emulator, meaning it is always available once
installed, regardless of how the environment changes"
* tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc:
binfmt_misc: add F option description to documentation
binfmt_misc: add persistent opened binary handler for containers
fs: add filp_clone_open API
|
|
In most cases, EPERM is returned on immutable inode, and there're only a
few places returning EACCES. I noticed this when running LTP on
overlayfs, setxattr03 failed due to unexpected EACCES on immutable
inode.
So converting all EACCES to EPERM on immutable inode.
Acked-by: Dave Chinner <[email protected]>
Signed-off-by: Eryu Guan <[email protected]>
Signed-off-by: Al Viro <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more vfs updates from Al Viro:
"Assorted cleanups and fixes.
In the "trivial API change" department - ->d_compare() losing 'parent'
argument"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cachefiles: Fix race between inactivating and culling a cache object
9p: use clone_fid()
9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()"
vfs: make dentry_needs_remove_privs() internal
vfs: remove file_needs_remove_privs()
vfs: fix deadlock in file_remove_privs() on overlayfs
get rid of 'parent' argument of ->d_compare()
cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare()
affs ->d_compare(): don't bother with ->d_inode
fold _d_rehash() and __d_rehash() together
fold dentry_rcuwalk_invalidate() into its only remaining caller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull more xfs updates from Dave Chinner:
"This is the second part of the XFS updates for this merge cycle, and
contains the new reverse block mapping feature for XFS.
Reverse mapping allows us to track the owner of a specific block on
disk precisely. It is implemented as a set of btrees (one per
allocation group) that track the owners of allocated extents.
Effectively it is a "used space tree" that is updated when we allocate
or free extents. i.e. it is coherent with the free space btrees we
already maintain and never overlaps with them.
This reverse mapping infrastructure is the building block of several
upcoming features - reflink, copy-on-write data, dedupe, online
metadata and data scrubbing, highly accurate bad sector/data loss
reporting to users, and significantly improved reconstruction of
damaged and corrupted filesystems. There's a lot of new stuff coming
along in the next couple of cycles,a nd it all builds in the rmap
infrastructure.
As such, it's a huge chunk of new code with new on-disk format
features and internal infrastructure. It warns at mount time as an
experimental feature and that it may eat data (as we do with all new
on-disk features until they stabilise). We have not released
userspace suport for it yet - userspace support currently requires
download from Darrick's xfsprogs repo and build from source, so the
access to this feature is really developer/tester only at this point.
Initial userspace support will be released at the same time kernel
with this code in it is released.
The new rmap enabled code regresses 3 xfstests - all are ENOSPC
related corner cases, one of which Darrick posted a fix for a few
hours ago. The other two are fixed by infrastructure that is part of
the upcoming reflink patchset. This new ENOSPC infrastructure
requires a on-disk format tweak required to keep mount times in
check - we need to keep an on-disk count of allocated rmapbt blocks so
we don't have to scan the entire btrees at mount time to count them.
This is currently being tested and will be part of the fixes sent in
the next week or two so users will not be exposed to this change"
* tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (52 commits)
xfs: move (and rename) the deferred bmap-free tracepoints
xfs: collapse single use static functions
xfs: remove unnecessary parentheses from log redo item recovery functions
xfs: remove the extents array from the rmap update done log item
xfs: in btree_lshift, only allocate temporary cursor when needed
xfs: remove unnecesary lshift/rshift key initialization
xfs: remove the get*keys and update_keys btree ops pointers
xfs: enable the rmap btree functionality
xfs: don't update rmapbt when fixing agfl
xfs: disable XFS_IOC_SWAPEXT when rmap btree is enabled
xfs: add rmap btree block detection to log recovery
xfs: add rmap btree geometry feature flag
xfs: propagate bmap updates to rmapbt
xfs: enable the xfs_defer mechanism to process rmaps to update
xfs: log rmap intent items
xfs: create rmap update intent log items
xfs: add rmap btree insert and delete helpers
xfs: convert unwritten status of reverse mappings
xfs: remove an extent from the rmap btree
xfs: add an extent to the rmap btree
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull qstr constification updates from Al Viro:
"Fairly self-contained bunch - surprising lot of places passes struct
qstr * as an argument when const struct qstr * would suffice; it
complicates analysis for no good reason.
I'd prefer to feed that separately from the assorted fixes (those are
in #for-linus and with somewhat trickier topology)"
* 'work.const-qstr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
qstr: constify instances in adfs
qstr: constify instances in lustre
qstr: constify instances in f2fs
qstr: constify instances in ext2
qstr: constify instances in vfat
qstr: constify instances in procfs
qstr: constify instances in fuse
qstr constify instances in fs/dcache.c
qstr: constify instances in nfs
qstr: constify instances in ocfs2
qstr: constify instances in autofs4
qstr: constify instances in hfs
qstr: constify instances in hfsplus
qstr: constify instances in logfs
qstr: constify dentry_init_security
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull mailcap fixlets from Mauro Carvalho Chehab:
"A small fixup for my and Shuah's entries in .mailcap.
Basically, those entries were with a syntax that makes
get_maintainer.pl to do the wrong thing"
* tag 'media/v4.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
.mailmap: Correct entries for Mauro Carvalho Chehab and Shuah Khan
|
|
Pull virtio/vhost updates from Michael Tsirkin:
- new vsock device support in host and guest
- platform IOMMU support in host and guest, including compatibility
quirks for legacy systems.
- misc fixes and cleanups.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
VSOCK: Use kvfree()
vhost: split out vringh Kconfig
vhost: detect 32 bit integer wrap around
vhost: new device IOTLB API
vhost: drop vringh dependency
vhost: convert pre sorted vhost memory array to interval tree
vhost: introduce vhost memory accessors
VSOCK: Add Makefile and Kconfig
VSOCK: Introduce vhost_vsock.ko
VSOCK: Introduce virtio_transport.ko
VSOCK: Introduce virtio_vsock_common.ko
VSOCK: defer sock removal to transports
VSOCK: transport-specific vsock_transport functions
vhost: drop vringh dependency
vop: pull in vhost Kconfig
virtio: new feature to detect IOMMU device quirk
balloon: check the number of available pages in leak balloon
vhost: lockless enqueuing
vhost: simplify work flushing
|
|
Pull more KVM updates from Paolo Bonzini:
- ARM bugfix and MSI injection support
- x86 nested virt tweak and OOPS fix
- Simplify pvclock code (vdso bits acked by Andy Lutomirski).
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
nvmx: mark ept single context invalidation as supported
nvmx: remove comment about missing nested vpid support
KVM: lapic: fix access preemption timer stuff even if kernel_irqchip=off
KVM: documentation: fix KVM_CAP_X2APIC_API information
x86: vdso: use __pvclock_read_cycles
pvclock: introduce seqcount-like API
arm64: KVM: Set cpsr before spsr on fault injection
KVM: arm: vgic-irqfd: Workaround changing kvm_set_routing_entry prototype
KVM: arm/arm64: Enable MSI routing
KVM: arm/arm64: Enable irqchip routing
KVM: Move kvm_setup_default/empty_irq_routing declaration in arch specific header
KVM: irqchip: Convey devid to kvm_set_msi
KVM: Add devid in kvm_kernel_irq_routing_entry
KVM: api: Pass the devid in the msi routing entry
|