| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
- A fix for OMAP5 and DRA7 to make the branch predictor hardening
settings take proper effect on secondary cores
- Disable USB OTG on am3517 since current driver isn't working
- Fix thermal sensor register settings on Armada 38x
- Fix suspend/resume IRQs on pxa3xx
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
ARM: pxa: irq: fix handling of ICMR registers in suspend/resume
ARM: dts: armada-38x: use the new thermal binding
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for 4.18:
- an important core fix for RTCs using the core offsetting only one
driver is affected
- a fix for the error path of mrst"
* tag 'rtc-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: fix alarm read and set offset
rtc: mrst: fix error code in probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two omap fixes for v4.18-rc cycle
Turns out the recent patches for ARM branch predictor hardening are
not working on omap5 and dra7 as planned because the secondary CPU
is parked to the bootrom code. We can't configure it in the bootloader.
So we must enable invalidates of BTB for omap5 and dra7 secondary
core in the kernel.
And there's a fix for reserved register access for am3517. The
usb otg module on am3517 is not the same as for other omap3.
* tag 'omap-for-v4.18/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
Signed-off-by: Olof Johansson <[email protected]>
|
|
mvebu fixes for 4.18 (part 1)
Use the new thermal binding on Armada 38x allowing to use a driver fix
which is already part of the kernel.
* tag 'mvebu-fixes-4.18-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: use the new thermal binding
Signed-off-by: Olof Johansson <[email protected]>
|
|
This is the fixes set for v4.18 cycle.
This is a fix for suspending all pxa3xx platforms, where high
number interrupts are not reenabled.
* tag 'pxa-fixes-4.18' of https://github.com/rjarzmik/linux:
ARM: pxa: irq: fix handling of ICMR registers in suspend/resume
Signed-off-by: Olof Johansson <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two related fixes for a boot failure of Xen PV guests"
* tag 'for-linus-4.18-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: setup pv irq ops vector earlier
xen: remove global bit from __default_kernel_pte_mask for pv guests
|
|
Pull block fix from Jens Axboe:
"Just a single regression fix (from 4.17) for bsg, fixing an EINVAL
return on non-data commands"
* tag 'for-linus-20180713' of git://git.kernel.dk/linux-block:
bsg: fix bogus EINVAL on non-data commands
|
|
Merge misc fixes from Andrew Morton:
"11 fixes"
* emailed patches form Andrew Morton <[email protected]>:
reiserfs: fix buffer overflow with long warning messages
checkpatch: fix duplicate invalid vsprintf pointer extension '%p<foo>' messages
mm: do not bug_on on incorrect length in __mm_populate()
mm/memblock.c: do not complain about top-down allocations for !MEMORY_HOTREMOVE
fs, elf: make sure to page align bss in load_elf_library
x86/purgatory: add missing FORCE to Makefile target
net/9p/client.c: put refcount of trans_mod in error case in parse_opts()
mm: allow arch to supply p??_free_tlb functions
autofs: fix slab out of bounds read in getname_kernel()
fs/proc/task_mmu.c: fix Locked field in /proc/pid/smaps*
mm: do not drop unused pages when userfaultd is running
|
|
ReiserFS prepares log messages into a 1024-byte buffer with no bounds
checks. Long messages, such as the "unknown mount option" warning when
userspace passes a crafted mount options string, overflow this buffer.
This causes KASAN to report a global-out-of-bounds write.
Fix it by truncating messages to the buffer size.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: [email protected]
Signed-off-by: Eric Biggers <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Multiline statements with invalid %p<foo> uses produce multiple
warnings. Fix that.
e.g.:
$ cat t_block.c
void foo(void)
{
MY_DEBUG(drv->foo,
"%pk",
foo->boo);
}
$ ./scripts/checkpatch.pl -f t_block.c
WARNING: Missing or malformed SPDX-License-Identifier tag in line 1
#1: FILE: t_block.c:1:
+void foo(void)
WARNING: Invalid vsprintf pointer extension '%pk'
#3: FILE: t_block.c:3:
+ MY_DEBUG(drv->foo,
+ "%pk",
+ foo->boo);
WARNING: Invalid vsprintf pointer extension '%pk'
#3: FILE: t_block.c:3:
+ MY_DEBUG(drv->foo,
+ "%pk",
+ foo->boo);
total: 0 errors, 3 warnings, 6 lines checked
NOTE: For some of the reported defects, checkpatch may be able to
mechanically convert to the typical style using --fix or --fix-inplace.
t_block.c has style problems, please review.
NOTE: If any of the errors are false positives, please report
them to the maintainer, see CHECKPATCH in MAINTAINERS.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Joe Perches <[email protected]>
Cc: "Tobin C. Harding" <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
syzbot has noticed that a specially crafted library can easily hit
VM_BUG_ON in __mm_populate
kernel BUG at mm/gup.c:1242!
invalid opcode: 0000 [#1] SMP
CPU: 2 PID: 9667 Comm: a.out Not tainted 4.18.0-rc3 #644
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 05/19/2017
RIP: 0010:__mm_populate+0x1e2/0x1f0
Code: 55 d0 65 48 33 14 25 28 00 00 00 89 d8 75 21 48 83 c4 20 5b 41 5c 41 5d 41 5e 41 5f 5d c3 e8 75 18 f1 ff 0f 0b e8 6e 18 f1 ff <0f> 0b 31 db eb c9 e8 93 06 e0 ff 0f 1f 00 55 48 89 e5 53 48 89 fb
Call Trace:
vm_brk_flags+0xc3/0x100
vm_brk+0x1f/0x30
load_elf_library+0x281/0x2e0
__ia32_sys_uselib+0x170/0x1e0
do_fast_syscall_32+0xca/0x420
entry_SYSENTER_compat+0x70/0x7f
The reason is that the length of the new brk is not page aligned when we
try to populate the it. There is no reason to bug on that though.
do_brk_flags already aligns the length properly so the mapping is
expanded as it should. All we need is to tell mm_populate about it.
Besides that there is absolutely no reason to to bug_on in the first
place. The worst thing that could happen is that the last page wouldn't
get populated and that is far from putting system into an inconsistent
state.
Fix the issue by moving the length sanitization code from do_brk_flags
up to vm_brk_flags. The only other caller of do_brk_flags is brk
syscall entry and it makes sure to provide the proper length so t here
is no need for sanitation and so we can use do_brk_flags without it.
Also remove the bogus BUG_ONs.
[[email protected]: fix up vm_brk_flags s@request@len@]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Michal Hocko <[email protected]>
Reported-by: syzbot <[email protected]>
Tested-by: Tetsuo Handa <[email protected]>
Reviewed-by: Oscar Salvador <[email protected]>
Cc: Zi Yan <[email protected]>
Cc: "Aneesh Kumar K.V" <[email protected]>
Cc: Dan Williams <[email protected]>
Cc: "Kirill A. Shutemov" <[email protected]>
Cc: Michael S. Tsirkin <[email protected]>
Cc: Al Viro <[email protected]>
Cc: "Huang, Ying" <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Mike Rapoport is converting architectures from bootmem to nobootmem
allocator. While doing so for m68k Geert has noticed that he gets a
scary looking warning:
WARNING: CPU: 0 PID: 0 at mm/memblock.c:230
memblock_find_in_range_node+0x11c/0x1be
memblock: bottom-up allocation failed, memory hotunplug may be affected
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted
4.18.0-rc3-atari-01343-gf2fb5f2e09a97a3c-dirty #7
Call Trace: __warn+0xa8/0xc2
kernel_pg_dir+0x0/0x1000
netdev_lower_get_next+0x2/0x22
warn_slowpath_fmt+0x2e/0x36
memblock_find_in_range_node+0x11c/0x1be
memblock_find_in_range_node+0x11c/0x1be
memblock_find_in_range_node+0x0/0x1be
vprintk_func+0x66/0x6e
memblock_virt_alloc_internal+0xd0/0x156
netdev_lower_get_next+0x2/0x22
netdev_lower_get_next+0x2/0x22
kernel_pg_dir+0x0/0x1000
memblock_virt_alloc_try_nid_nopanic+0x58/0x7a
netdev_lower_get_next+0x2/0x22
kernel_pg_dir+0x0/0x1000
kernel_pg_dir+0x0/0x1000
EXPTBL+0x234/0x400
EXPTBL+0x234/0x400
alloc_node_mem_map+0x4a/0x66
netdev_lower_get_next+0x2/0x22
free_area_init_node+0xe2/0x29e
EXPTBL+0x234/0x400
paging_init+0x430/0x462
kernel_pg_dir+0x0/0x1000
printk+0x0/0x1a
EXPTBL+0x234/0x400
setup_arch+0x1b8/0x22c
start_kernel+0x4a/0x40a
_sinittext+0x344/0x9e8
The warning is basically saying that a top-down allocation can break
memory hotremove because memblock allocation is not movable. But m68k
doesn't even support MEMORY_HOTREMOVE so there is no point to warn about
it.
Make the warning conditional only to configurations that care.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Michal Hocko <[email protected]>
Reported-by: Geert Uytterhoeven <[email protected]>
Tested-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: Mike Rapoport <[email protected]>
Cc: Greg Ungerer <[email protected]>
Cc: Sam Creasey <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The current code does not make sure to page align bss before calling
vm_brk(), and this can lead to a VM_BUG_ON() in __mm_populate() due to
the requested lenght not being correctly aligned.
Let us make sure to align it properly.
Kees: only applicable to CONFIG_USELIB kernels: 32-bit and configured
for libc5.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Oscar Salvador <[email protected]>
Reported-by: [email protected]
Tested-by: Tetsuo Handa <[email protected]>
Acked-by: Kees Cook <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Nicolas Pitre <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
- Build the kernel without the fix
- Add some flag to the purgatories KBUILD_CFLAGS,I used
-fno-asynchronous-unwind-tables
- Re-build the kernel
When you look at makes output you see that sha256.o is not re-build in the
last step. Also readelf -S still shows the .eh_frame section for
sha256.o.
With the fix sha256.o is rebuilt in the last step.
Without FORCE make does not detect changes only made to the command line
options. So object files might not be re-built even when they should be.
Fix this by adding FORCE where it is missing.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: df6f2801f511 ("kernel/kexec_file.c: move purgatories sha256 to common code")
Signed-off-by: Philipp Rudo <[email protected]>
Acked-by: Dave Young <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: <[email protected]> [4.17+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
In my testing, the second mount will fail after umounting successfully.
The reason is that we put refcount of trans_mod in the correct case
rather than the error case in parse_opts() at last. That will cause the
refcount decrease to -1, and when we try to get trans_mod again in
try_module_get(), we could only increase refcount to 0 which will cause
failure as follows:
parse_opts
v9fs_get_trans_by_name
try_module_get : return NULL to caller which cause error
So we should put refcount of trans_mod in error case.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 9421c3e64137ec ("net/9p/client.c: fix potential refcnt problem of trans module")
Signed-off-by: Jun Piao <[email protected]>
Reviewed-by: Yiwen Jiang <[email protected]>
Reviewed-by: Greg Kurz <[email protected]>
Reviewed-by: Dominique Martinet <[email protected]>
Tested-by: Dominique Martinet <[email protected]>
Cc: Eric Van Hensbergen <[email protected]>
Cc: Ron Minnich <[email protected]>
Cc: Latchesar Ionkov <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The mmu_gather APIs keep track of the invalidated address range
including the span covered by invalidated page table pages. Ranges
covered by page tables but not ptes (and therefore no TLBs) still need
to be invalidated because some architectures (x86) can cache
intermediate page table entries, and invalidate those with normal TLB
invalidation instructions to be almost-backward-compatible.
Architectures which don't cache intermediate page table entries, or
which invalidate these caches separately from TLB invalidation, do not
require TLB invalidation range expanded over page tables.
Allow architectures to supply their own p??_free_tlb functions, which
can avoid the __tlb_adjust_range.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Nicholas Piggin <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Cc: "Aneesh Kumar K. V" <[email protected]>
Cc: Minchan Kim <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: Nadav Amit <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The autofs subsystem does not check that the "path" parameter is present
for all cases where it is required when it is passed in via the "param"
struct.
In particular it isn't checked for the AUTOFS_DEV_IOCTL_OPENMOUNT_CMD
ioctl command.
To solve it, modify validate_dev_ioctl(function to check that a path has
been provided for ioctl commands that require it.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Tomas Bortoli <[email protected]>
Signed-off-by: Ian Kent <[email protected]>
Reported-by: [email protected]
Cc: Dmitry Vyukov <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Thomas reports:
"While looking around in /proc on my v4.14.52 system I noticed that all
processes got a lot of "Locked" memory in /proc/*/smaps. A lot more
memory than a regular user can usually lock with mlock().
Commit 493b0e9d945f (in v4.14-rc1) seems to have changed the behavior
of "Locked".
Before that commit the code was like this. Notice the VM_LOCKED check.
(vma->vm_flags & VM_LOCKED) ?
(unsigned long)(mss.pss >> (10 + PSS_SHIFT)) : 0);
After that commit Locked is now the same as Pss:
(unsigned long)(mss->pss >> (10 + PSS_SHIFT)));
This looks like a mistake."
Indeed, the commit has added mss->pss_locked with the correct value that
depends on VM_LOCKED, but forgot to actually use it. Fix it.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 493b0e9d945f ("mm: add /proc/pid/smaps_rollup")
Signed-off-by: Vlastimil Babka <[email protected]>
Reported-by: Thomas Lindroth <[email protected]>
Cc: Alexey Dobriyan <[email protected]>
Cc: Daniel Colascione <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
KVM guests on s390 can notify the host of unused pages. This can result
in pte_unused callbacks to be true for KVM guest memory.
If a page is unused (checked with pte_unused) we might drop this page
instead of paging it. This can have side-effects on userfaultd, when
the page in question was already migrated:
The next access of that page will trigger a fault and a user fault
instead of faulting in a new and empty zero page. As QEMU does not
expect a userfault on an already migrated page this migration will fail.
The most straightforward solution is to ignore the pte_unused hint if a
userfault context is active for this VMA.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Christian Borntraeger <[email protected]>
Cc: Martin Schwidefsky <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Cc: Mike Rapoport <[email protected]>
Cc: Janosch Frank <[email protected]>
Cc: David Hildenbrand <[email protected]>
Cc: Cornelia Huck <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
We must zero struct pages for memory that is not backed by physical
memory, or kernel does not have access to.
Recently, there was a change which zeroed all memmap for all holes in
e820. Unfortunately, it introduced a bug that is discussed here:
https://www.spinics.net/lists/linux-mm/msg156764.html
Linus, also saw this bug on his machine, and confirmed that reverting
commit 124049decbb1 ("x86/e820: put !E820_TYPE_RAM regions into
memblock.reserved") fixes the issue.
The problem is that we incorrectly zero some struct pages after they
were setup.
The fix is to zero unavailable struct pages prior to initializing of
struct pages.
A more detailed fix should come later that would avoid double zeroing
cases: one in __init_single_page(), the other one in
zero_resv_unavail().
Fixes: 124049decbb1 ("x86/e820: put !E820_TYPE_RAM regions into memblock.reserved")
Signed-off-by: Pavel Tatashin <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- I2C core bugfix regarding bus recovery
- driver bugfix for the tegra driver
- typo correction
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: recovery: if possible send STOP with recovery pulses
i2c: tegra: Fix NACK error handling
i2c: stu300: use non-archaic spelling of failes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"A clocksource driver fix and a revert"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: arm_arch_timer: Set arch_mem_timer cpumask to cpu_possible_mask
Revert "tick: Prefer a lower rating device only if it's CPU local device"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tool fixes from Ingo Molnar:
"Misc tooling fixes: python3 related fixes, gcc8 fix, bashism fixes and
some other smaller fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Use python-config --includes rather than --cflags
perf script python: Fix dict reference counting
perf stat: Fix --interval_clear option
perf tools: Fix compilation errors on gcc8
perf test shell: Prevent temporary editor files from being considered test scripts
perf llvm-utils: Remove bashism from kernel include fetch script
perf test shell: Make perf's inet_pton test more portable
perf test shell: Replace '|&' with '2>&1 |' to work with more shells
perf scripts python: Add Python 3 support to EventClass.py
perf scripts python: Add Python 3 support to sched-migration.py
perf scripts python: Add Python 3 support to Util.py
perf scripts python: Add Python 3 support to SchedGui.py
perf scripts python: Add Python 3 support to Core.py
perf tools: Generate a Python script compatible with Python 2 and 3
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Ingo Molnar:
"Fix a UEFI mixed mode (64-bit kernel on 32-bit UEFI) reboot loop
regression"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix mixed mode reboot loop by removing pointless call to PciIo->Attributes()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rseq fixes from Ingo Molnar:
"Various rseq ABI fixes and cleanups: use get_user()/put_user(),
validate parameters and use proper uapi types, etc"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq/selftests: cleanup: Update comment above rseq_prepare_unload
rseq: Remove unused types_32_64.h uapi header
rseq: uapi: Declare rseq_cs field as union, update includes
rseq: uapi: Update uapi comments
rseq: Use get_user/put_user rather than __get_user/__put_user
rseq: Use __u64 for rseq_cs fields, validate user inputs
|
|
Pull rdma fixes from Jason Gunthorpe:
"Things have been quite slow, only 6 RC patches have been sent to the
list. Regression, user visible bugs, and crashing fixes:
- cxgb4 could wrongly fail MR creation due to a typo
- various crashes if the wrong QP type is mixed in with APIs that
expect other types
- syzkaller oops
- using ERR_PTR and NULL together cases HFI1 to crash in some cases
- mlx5 memory leak in error unwind"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Fix memory leak in mlx5_ib_create_srq() error path
RDMA/uverbs: Don't fail in creation of multiple flows
IB/hfi1: Fix incorrect mixing of ERR_PTR and NULL return values
RDMA/uverbs: Fix slab-out-of-bounds in ib_uverbs_ex_create_flow
RDMA/uverbs: Protect from attempts to create flows on unsupported QP
iw_cxgb4: correctly enforce the max reg_mr depth
|
|
Pull VFIO fix from Alex Williamson:
"Fix deadlock in mbochs sample driver (Alexey Khoroshilov)"
* tag 'vfio-v4.18-rc5' of git://github.com/awilliam/linux-vfio:
sample: vfio-mdev: avoid deadlock in mdev_access()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- update Kbuild and Kconfig documents
- sanitize -I compiler option handling
- update extract-vmlinux script to recognize LZ4 and ZSTD
- fix tools Makefiles
- update tags.sh to handle __ro_after_init
- suppress warnings in case getconf does not recognize LFS_* parameters
* tag 'kbuild-fixes-v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: suppress warnings from 'getconf LFS_*'
scripts/tags.sh: add __ro_after_init
tools: build: Use HOSTLDFLAGS with fixdep
tools: build: Fixup host c flags
tools build: fix # escaping in .cmd files for future Make
scripts: teach extract-vmlinux about LZ4 and ZSTD
kbuild: remove duplicated comments about PHONY
kbuild: .PHONY is not a variable, but PHONY is
kbuild: do not drop -I without parameter
kbuild: document the KBUILD_KCONFIG env. variable
kconfig: update user kconfig tools doc.
kbuild: delete INSTALL_FW_PATH from kbuild documentation
kbuild: update ARCH alias info for sparc
kbuild: update ARCH alias info for sh
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Catalin's out enjoying the sunshine, so I'm sending the fixes for a
couple of weeks (although there hopefully won't be any more!).
We've got a revert of a previous fix because it broke the build with
some distro toolchains and a preemption fix when detemining whether or
not the SIMD unit is in use.
Summary:
- Revert back to the 'linux' target for LD, as 'elf' breaks some
distributions
- Fix preemption race when testing whether the vector unit is in use
or not"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: neon: Fix function may_use_simd() return error status
Revert "arm64: Use aarch64elf and aarch64elfb emulation mode variants"
|
|
Pull ARM fixes from Russell King:
"A couple of small fixes this time around from Steven for an
interaction between ftrace and kernel read-only protection, and
Vladimir for nommu"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8780/1: ftrace: Only set kernel memory back to read-only after boot
ARM: 8775/1: NOMMU: Use instr_sync instead of plain isb in common code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixlet from Steven Rostedt:
"Joel Fernandes asked to add a feature in tracing that Android had its
own patch internally for. I took it back in 4.13. Now he realizes that
he had a mistake, and swapped the values from what Android had. This
means that the old Android tools will break when using a new kernel
that has the new feature on it.
The options are:
1. To swap it back to what Android wants.
2. Add a command line option or something to do the swap
3. Just let Android carry a patch that swaps it back
Since it requires setting a tracing option to enable this anyway, I
doubt there are other users of this than Android. Thus, I've decided
to take option 1. If someone else is actually depending on the order
that is in the kernel, then we will have to revert this change and go
to option 2 or 3"
* tag 'trace-v4.18-rc3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Reorder display of TGID to be after PID
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few HD-auio fixes: one fix for a possible mutex deadlock at
HDMI hotplug handling is somewhat subtle and delicate, while the rest
are usual device-specific quirks"
* tag 'sound-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/ca0132: Update a pci quirk device name
ALSA: hda/ca0132: Add Recon3Di quirk for Gigabyte G1.Sniper Z97
ALSA: hda/realtek - two more lenovo models need fixup of MIC_LOCATION
ALSA: hda - Handle pm failure during hotplug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dave Jiang:
- ensure that a variable passed in by reference to acpi_nfit_ctl is
always set to a value. An incremental patch is provided due to notice
from testing in -next. The rest of the commits did not exhibit
issues.
- fix a return path in nsio_rw_bytes() that was not returning "bytes
remain" as expected for the function.
- address an issue where applications polling on scrub-completion for
the NVDIMM may falsely wakeup and read the wrong state value and
cause hang.
- change the test unit persistent capability attribute to fix up a
broken assumption in the unit test infrastructure wrt the
'write_cache' attribute
- ratelimit dev_info() in the dax device check_vma() function since
this is easily triggered from userspace
* tag 'libnvdimm-fixes-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: fix unchecked dereference in acpi_nfit_ctl
acpi, nfit: Fix scrub idle detection
tools/testing/nvdimm: advertise a write cache for nfit_test
acpi/nfit: fix cmd_rc for acpi_nfit_ctl to always return a value
dev-dax: check_vma: ratelimit dev_info-s
libnvdimm, pmem: Fix memcpy_mcsafe() return code handling in nsio_rw_bytes()
|
|
This patch adds r8a77990 xhci support. The driver will use
the fallback compatible string "renesas,rcar-gen3-xhci".
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Remove test_bitmap noise which is a result of cut and paste error.
There is no need for this modprobe -q -r test_bitmap noise in this
test.
Signed-off-by: Shuah Khan (Samsung OSG) <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The tools/usb/ffs-test.c file defines cpu_to_le16/32 by using the C
library htole16/32 function calls. However, cpu_to_le16/32 are used when
initializing structures, i.e in a context where a function call is not
allowed.
It works fine on little endian systems because htole16/32 are defined by
the C library as no-ops. But on big-endian systems, they are actually
doing something, which might involve calling a function, causing build
failures, such as:
ffs-test.c:48:25: error: initializer element is not constant
#define cpu_to_le32(x) htole32(x)
^~~~~~~
ffs-test.c:128:12: note: in expansion of macro ‘cpu_to_le32’
.magic = cpu_to_le32(FUNCTIONFS_DESCRIPTORS_MAGIC_V2),
^~~~~~~~~~~
To solve this, we code cpu_to_le16/32 in a way that allows them to be
used when initializing structures. This fix was imported from
meta-openembedded/android-tools/fix-big-endian-build.patch written by
Thomas Petazzoni <[email protected]>.
CC: Thomas Petazzoni <[email protected]>
Signed-off-by: Peter Senna Tschudin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Variable maxpacket is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'maxpacket' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Pointer dev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Variable num_ports is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'num_ports' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Variable t is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 't' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Pointer dbc is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
variable 'dbc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Variable 'selector' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'selector' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Variable modey is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'modey' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Pointer usbdev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'usbdev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Pointer ep is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'ep' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The offset needs to be added after reading the alarm value.
It also needs to be subtracted after the now < alarm test.
Tested-by: Jon Hunter <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
Setting pv_irq_ops for Xen PV domains should be done as early as
possible in order to support e.g. very early printk() usage.
The same applies to xen_vcpu_info_reset(0), as it is needed for the
pv irq ops.
Move the call of xen_setup_machphys_mapping() after initializing the
pv functions as it contains a WARN_ON(), too.
Remove the no longer necessary conditional in xen_init_irq_ops()
from PVH V1 times to make clear this is a PV only function.
Cc: <[email protected]> # 4.14
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Boris Ostrovsky <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
|
|
Currently ftrace displays data in trace output like so:
_-----=> irqs-off
/ _----=> need-resched
| / _---=> hardirq/softirq
|| / _--=> preempt-depth
||| / delay
TASK-PID CPU TGID |||| TIMESTAMP FUNCTION
| | | | |||| | |
bash-1091 [000] ( 1091) d..2 28.313544: sched_switch:
However Android's trace visualization tools expect a slightly different
format due to an out-of-tree patch patch that was been carried for a
decade, notice that the TGID and CPU fields are reversed:
_-----=> irqs-off
/ _----=> need-resched
| / _---=> hardirq/softirq
|| / _--=> preempt-depth
||| / delay
TASK-PID TGID CPU |||| TIMESTAMP FUNCTION
| | | | |||| | |
bash-1091 ( 1091) [002] d..2 64.965177: sched_switch:
From kernel v4.13 onwards, during which TGID was introduced, tracing
with systrace on all Android kernels will break (most Android kernels
have been on 4.9 with Android patches, so this issues hasn't been seen
yet). From v4.13 onwards things will break.
The chrome browser's tracing tools also embed the systrace viewer which
uses the legacy TGID format and updates to that are known to be
difficult to make.
Considering this, I suggest we make this change to the upstream kernel
and backport it to all Android kernels. I believe this feature is merged
recently enough into the upstream kernel that it shouldn't be a problem.
Also logically, IMO it makes more sense to group the TGID with the
TASK-PID and the CPU after these.
Link: http://lkml.kernel.org/r/[email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Fixes: 441dae8f2f29 ("tracing: Add support for display of tgid in trace output")
Signed-off-by: Joel Fernandes (Google) <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|