aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2019-08-31net: aquantia: linkstate irq should be oneshotIgor Russkikh1-1/+1
Declaring threaded irq handler should also indicate the irq is oneshot. It is oneshot indeed, because HW implements irq automasking on trigger. Not declaring this causes some kernel configurations to fail on interface up, because request_threaded_irq returned an err code. The issue was originally hidden on normal x86_64 configuration with latest kernel, because depending on interrupt controller, irq driver added ONESHOT flag on its own. Issue was observed on older kernels (4.14) where no such logic exists. Fixes: 4c83f170b3ac ("net: aquantia: link status irq handling") Signed-off-by: Igor Russkikh <[email protected]> Reported-by: Michael Symolkin <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-08-31net: aquantia: reapply vlan filters on upDmitry Bogdanov1-0/+4
In case of device reconfiguration the driver may reset the device invisible for other modules, vlan module in particular. So vlans will not be removed&created and vlan filters will not be configured in the device. The patch reapplies the vlan filters at device start. Fixes: 7975d2aff5afb ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov <[email protected]> Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-08-31net: aquantia: fix limit of vlan filtersDmitry Bogdanov1-1/+1
Fix a limit condition of vlans on the interface before setting vlan promiscuous mode Fixes: 48dd73d08d4dd ("net: aquantia: fix vlans not working over bridged network") Signed-off-by: Dmitry Bogdanov <[email protected]> Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-08-31net: aquantia: fix removal of vlan 0Dmitry Bogdanov1-1/+2
Due to absence of checking against the rx flow rule when vlan 0 is being removed, the other rule could be removed instead of the rule with vlan 0 Fixes: 7975d2aff5afb ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov <[email protected]> Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-08-31Merge branch 'Fix-issues-in-tc-taprio-and-tc-cbs'David S. Miller2-22/+28
Vladimir Oltean says: ==================== Fix issues in tc-taprio and tc-cbs This series fixes one panic and one WARN_ON found in the tc-taprio qdisc, while trying to apply it: - On an interface which is not multi-queue - On an interface which has no carrier The tc-cbs was also visually found to suffer of the same issue as tc-taprio, and the fix was only compile-tested in that case. ==================== Signed-off-by: David S. Miller <[email protected]>
2019-08-31net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rateVladimir Oltean1-8/+11
The discussion to be made is absolutely the same as in the case of previous patch ("taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte"). Nothing is lost when setting a default. Cc: Leandro Dorileo <[email protected]> Fixes: e0a7683d30e9 ("net/sched: cbs: fix port_rate miscalculation") Acked-by: Vinicius Costa Gomes <[email protected]> Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-08-31taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byteVladimir Oltean1-10/+13
The taprio budget needs to be adapted at runtime according to interface link speed. But that handling is problematic. For one thing, installing a qdisc on an interface that doesn't have carrier is not illegal. But taprio prints the following stack trace: [ 31.851373] ------------[ cut here ]------------ [ 31.856024] WARNING: CPU: 1 PID: 207 at net/sched/sch_taprio.c:481 taprio_dequeue+0x1a8/0x2d4 [ 31.864566] taprio: dequeue() called with unknown picos per byte. [ 31.864570] Modules linked in: [ 31.873701] CPU: 1 PID: 207 Comm: tc Not tainted 5.3.0-rc5-01199-g8838fe023cd6 #1689 [ 31.881398] Hardware name: Freescale LS1021A [ 31.885661] [<c03133a4>] (unwind_backtrace) from [<c030d8cc>] (show_stack+0x10/0x14) [ 31.893368] [<c030d8cc>] (show_stack) from [<c10ac958>] (dump_stack+0xb4/0xc8) [ 31.900555] [<c10ac958>] (dump_stack) from [<c0349d04>] (__warn+0xe0/0xf8) [ 31.907395] [<c0349d04>] (__warn) from [<c0349d64>] (warn_slowpath_fmt+0x48/0x6c) [ 31.914841] [<c0349d64>] (warn_slowpath_fmt) from [<c0f38db4>] (taprio_dequeue+0x1a8/0x2d4) [ 31.923150] [<c0f38db4>] (taprio_dequeue) from [<c0f227b0>] (__qdisc_run+0x90/0x61c) [ 31.930856] [<c0f227b0>] (__qdisc_run) from [<c0ec82ac>] (net_tx_action+0x12c/0x2bc) [ 31.938560] [<c0ec82ac>] (net_tx_action) from [<c0302298>] (__do_softirq+0x130/0x3c8) [ 31.946350] [<c0302298>] (__do_softirq) from [<c03502a0>] (irq_exit+0xbc/0xd8) [ 31.953536] [<c03502a0>] (irq_exit) from [<c03a4808>] (__handle_domain_irq+0x60/0xb4) [ 31.961328] [<c03a4808>] (__handle_domain_irq) from [<c0754478>] (gic_handle_irq+0x58/0x9c) [ 31.969638] [<c0754478>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90) [ 31.977076] Exception stack(0xe8167b20 to 0xe8167b68) [ 31.982100] 7b20: e9d4bd80 00000cc0 000000cf 00000000 e9d4bd80 c1f38958 00000cc0 c1f38960 [ 31.990234] 7b40: 00000001 000000cf 00000004 e9dc0800 00000000 e8167b70 c0f478ec c0f46d94 [ 31.998363] 7b60: 60070013 ffffffff [ 32.001833] [<c0301a8c>] (__irq_svc) from [<c0f46d94>] (netlink_trim+0x18/0xd8) [ 32.009104] [<c0f46d94>] (netlink_trim) from [<c0f478ec>] (netlink_broadcast_filtered+0x34/0x414) [ 32.017930] [<c0f478ec>] (netlink_broadcast_filtered) from [<c0f47cec>] (netlink_broadcast+0x20/0x28) [ 32.027102] [<c0f47cec>] (netlink_broadcast) from [<c0eea378>] (rtnetlink_send+0x34/0x88) [ 32.035238] [<c0eea378>] (rtnetlink_send) from [<c0f25890>] (notify_and_destroy+0x2c/0x44) [ 32.043461] [<c0f25890>] (notify_and_destroy) from [<c0f25e08>] (qdisc_graft+0x398/0x470) [ 32.051595] [<c0f25e08>] (qdisc_graft) from [<c0f27a00>] (tc_modify_qdisc+0x3a4/0x724) [ 32.059470] [<c0f27a00>] (tc_modify_qdisc) from [<c0ee4c84>] (rtnetlink_rcv_msg+0x260/0x2ec) [ 32.067864] [<c0ee4c84>] (rtnetlink_rcv_msg) from [<c0f4a988>] (netlink_rcv_skb+0xb8/0x110) [ 32.076172] [<c0f4a988>] (netlink_rcv_skb) from [<c0f4a170>] (netlink_unicast+0x1b4/0x22c) [ 32.084392] [<c0f4a170>] (netlink_unicast) from [<c0f4a5e4>] (netlink_sendmsg+0x33c/0x380) [ 32.092614] [<c0f4a5e4>] (netlink_sendmsg) from [<c0ea9f40>] (sock_sendmsg+0x14/0x24) [ 32.100403] [<c0ea9f40>] (sock_sendmsg) from [<c0eaa780>] (___sys_sendmsg+0x214/0x228) [ 32.108279] [<c0eaa780>] (___sys_sendmsg) from [<c0eabad0>] (__sys_sendmsg+0x50/0x8c) [ 32.116068] [<c0eabad0>] (__sys_sendmsg) from [<c0301000>] (ret_fast_syscall+0x0/0x54) [ 32.123938] Exception stack(0xe8167fa8 to 0xe8167ff0) [ 32.128960] 7fa0: b6fa68c8 000000f8 00000003 bea142d0 00000000 00000000 [ 32.137093] 7fc0: b6fa68c8 000000f8 0052154c 00000128 5d6468a2 00000000 00000028 00558c9c [ 32.145224] 7fe0: 00000070 bea14278 00530d64 b6e17e64 [ 32.150659] ---[ end trace 2139c9827c3e5177 ]--- This happens because the qdisc ->dequeue callback gets called. Which again is not illegal, the qdisc will dequeue even when the interface is up but doesn't have carrier (and hence SPEED_UNKNOWN), and the frames will be dropped further down the stack in dev_direct_xmit(). And, at the end of the day, for what? For calculating the initial budget of an interface which is non-operational at the moment and where frames will get dropped anyway. So if we can't figure out the link speed, default to SPEED_10 and move along. We can also remove the runtime check now. Cc: Leandro Dorileo <[email protected]> Fixes: 7b9eba7ba0c1 ("net/sched: taprio: fix picos_per_byte miscalculation") Acked-by: Vinicius Costa Gomes <[email protected]> Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-08-31taprio: Fix kernel panic in taprio_destroyVladimir Oltean1-4/+4
taprio_init may fail earlier than this line: list_add(&q->taprio_list, &taprio_list); i.e. due to the net device not being multi queue. Attempting to remove q from the global taprio_list when it is not part of it will result in a kernel panic. Fix it by matching list_add and list_del better to one another in the order of operations. This way we can keep the deletion unconditional and with lower complexity - O(1). Cc: Leandro Dorileo <[email protected]> Fixes: 7b9eba7ba0c1 ("net/sched: taprio: fix picos_per_byte miscalculation") Signed-off-by: Vladimir Oltean <[email protected]> Acked-by: Vinicius Costa Gomes <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-08-31net: dsa: microchip: fill regmap_config nameGeorge McCollister1-0/+1
Use the register value width as the regmap_config name to prevent the following error when the second and third regmap_configs are initialized. "debugfs: Directory '${bus-id}' with parent 'regmap' already present!" Signed-off-by: George McCollister <[email protected]> Reviewed-by: Marek Vasut <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-08-31Merge tag 'batadv-net-for-davem-20190830' of git://git.open-mesh.org/linux-mergeDavid S. Miller2-13/+25
Simon Wunderlich says: ==================== Here are two batman-adv bugfixes: - Fix OGM and OGMv2 header read boundary check, by Sven Eckelmann (2 patches) ==================== Signed-off-by: David S. Miller <[email protected]>
2019-08-31tools/power turbostat: update version numberLen Brown1-1/+1
Today is 19.08.31, at least in some parts of the world. Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: Add support for Hygon Fam 18h (Dhyana) RAPLPu Wen1-2/+7
Commit 9392bd98bba760be96ee ("tools/power turbostat: Add support for AMD Fam 17h (Zen) RAPL") and the commit 3316f99a9f1b68c578c5 ("tools/power turbostat: Also read package power on AMD F17h (Zen)") add AMD Fam 17h RAPL support. Hygon Family 18h(Dhyana) support RAPL in bit 14 of CPUID 0x80000007 EDX, and has MSRs RAPL_PWR_UNIT/CORE_ENERGY_STAT/PKG_ENERGY_STAT. So add Hygon Dhyana Family 18h support for RAPL. Already tested on Hygon multi-node systems and it shows correct per-core energy usage and the total package power. Signed-off-by: Pu Wen <[email protected]> Reviewed-by: Calvin Walton <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: Fix caller parameter of get_tdp_amd()Pu Wen1-1/+1
Commit 9392bd98bba760be96ee ("tools/power turbostat: Add support for AMD Fam 17h (Zen) RAPL") add a function get_tdp_amd(), the parameter is CPU family. But the rapl_probe_amd() function use wrong model parameter. Fix the wrong caller parameter of get_tdp_amd() to use family. Cc: <[email protected]> # v5.1+ Signed-off-by: Pu Wen <[email protected]> Reviewed-by: Calvin Walton <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: Fix CPU%C1 display valueSrinivas Pandruvada1-6/+17
In some case C1% will be wrong value, when platform doesn't have MSR for C1 residency. For example: Core CPU CPU%c1 - - 100.00 0 0 100.00 0 2 100.00 1 1 100.00 1 3 100.00 But adding Busy% will fix this Core CPU Busy% CPU%c1 - - 99.77 0.23 0 0 99.77 0.23 0 2 99.77 0.23 1 1 99.77 0.23 1 3 99.77 0.23 This issue can be reproduced on most of the recent systems including Broadwell, Skylake and later. This is because if we don't select Busy% or Avg_MHz or Bzy_MHz then mperf value will not be read from MSR, so it will be 0. But this is required for C1% calculation when MSR for C1 residency is not present. Same is true for C3, C6 and C7 column selection. So add another define DO_BIC_READ(), which doesn't depend on user column selection and use for mperf, C3, C6 and C7 related counters. So when there is no platform support for C1 residency counters, we still read these counters, if the CPU has support and user selected display of CPU%c1. Signed-off-by: Srinivas Pandruvada <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: do not enforce 1msArtem Bityutskiy1-5/+0
Turbostat works by taking a snapshot of counters, sleeping, taking another snapshot, calculating deltas, and printing out the table. The sleep time is controlled via -i option or by user sending a signal or a character to stdin. In the latter case, turbostat always adds 1 ms sleep before it reads the counters, in order to avoid larger imprecisions in the results in prints. While the 1 ms delay may be a good idea for a "dumb" user, it is a problem for an "aware" user. I do thousands and thousands of measurements over a short period of time (like 2ms), and turbostat unconditionally adds a 1ms to my interval, so I cannot get what I really need. This patch removes the unconditional 1ms sleep. This is an expert user tool, after all, and non-experts will unlikely ever use it in the non-fixed interval mode anyway, so I think it is OK to remove the 1ms delay. Signed-off-by: Artem Bityutskiy <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: read from pipes tooArtem Bityutskiy1-4/+16
Commit '47936f944e78 tools/power turbostat: fix printing on input' make a valid fix, but it completely disabled piped stdin support, which is a valuable use-case. Indeed, if stdin is a pipe, turbostat won't read anything from it, so it becomes impossible to get turbostat output at user-defined moments, instead of the regular intervals. There is no reason why this should works for terminals, but not for pipes. This patch improves the situation. Instead of ignoring pipes, we read data from them but gracefully handle the EOF case. Signed-off-by: Artem Bityutskiy <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: Add Ice Lake NNPI supportRajneesh Bhardwaj1-0/+1
This enables turbostat utility on Ice Lake NNPI SoC. Link: https://lkml.org/lkml/2019/6/5/1034 Signed-off-by: Rajneesh Bhardwaj <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: rename has_hsw_msrs()Len Brown1-4/+4
Perhaps if this more descriptive name had been used, then we wouldn't have had the HSW ULT vs HSW CORE bug, fixed by the previous commit. Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: Fix Haswell Core systemsLen Brown1-4/+6
turbostat: cpu0: msr offset 0x630 read failed: Input/output error because Haswell Core does not have C8-C10. Output C8-C10 only on Haswell ULT. Fixes: f5a4c76ad7de ("tools/power turbostat: consolidate duplicate model numbers") Reported-by: Prarit Bhargava <[email protected]> Suggested-by: Kosuke Tatsukawa <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: add Jacobsville supportZhang Rui1-0/+3
Jacobsville behaves like Denverton. Signed-off-by: Zhang Rui <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: fix buffer overrunNaoya Horiguchi1-1/+1
turbostat could be terminated by general protection fault on some latest hardwares which (for example) support 9 levels of C-states and show 18 "tADDED" lines. That bloats the total output and finally causes buffer overrun. So let's extend the buffer to avoid this. Signed-off-by: Naoya Horiguchi <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: fix file descriptor leaksGustavo A. R. Silva1-0/+1
Fix file descriptor leaks by closing fp before return. Addresses-Coverity-ID: 1444591 ("Resource leak") Addresses-Coverity-ID: 1444592 ("Resource leak") Fixes: 5ea7647b333f ("tools/power turbostat: Warn on bad ACPI LPIT data") Signed-off-by: Gustavo A. R. Silva <[email protected]> Reviewed-by: Prarit Bhargava <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: fix leak of file descriptor on error return pathColin Ian King1-0/+1
Currently the error return path does not close the file fp and leaks a file descriptor. Fix this by closing the file. Fixes: 5ea7647b333f ("tools/power turbostat: Warn on bad ACPI LPIT data") Signed-off-by: Colin Ian King <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: Make interval calculation per thread to reduce jitterYazen Ghannam1-3/+10
Turbostat currently normalizes TSC and other values by dividing by an interval. This interval is the delta between the start of one global (all counters on all CPUs) sampling and the start of another. However, this introduces a lot of jitter into the data. In order to reduce jitter, the interval calculation should be based on timestamps taken per thread and close to the start of the thread's sampling. Define a per thread time value to hold the delta between samples taken on the thread. Use the timestamp taken at the beginning of sampling to calculate the delta. Move the thread's beginning timestamp to after the CPU migration to avoid jitter due to the migration. Use the global time delta for the average time delta. Signed-off-by: Yazen Ghannam <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power turbostat: remove duplicate pc10 columnLen Brown1-1/+0
Remove the duplicate pc10 column. Fixes: be0e54c4ebbf ("turbostat: Build-in "Low Power Idle" counters support") Reported-by: Naoya Horiguchi <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power x86_energy_perf_policy: Fix argument parsingZephaniah E. Loss-Cutler-Hull1-1/+1
The -w argument in x86_energy_perf_policy currently triggers an unconditional segfault. This is because the argument string reads: "+a:c:dD:E:e:f:m:M:rt:u:vw" and yet the argument handler expects an argument. When parse_optarg_string is called with a null argument, we then proceed to crash in strncmp, not horribly friendly. The man page describes -w as taking an argument, the long form (--hwp-window) is correctly marked as taking a required argument, and the code expects it. As such, this patch simply marks the short form (-w) as requiring an argument. Signed-off-by: Zephaniah E. Loss-Cutler-Hull <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power: Fix typo in man pageMatt Lupfer1-1/+1
From context, we mean EPB (Enegry Performance Bias). Signed-off-by: Matt Lupfer <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power/x86: Enable compiler optimisations and Fortify by defaultBen Hutchings2-2/+4
Compiling without optimisations is silly, especially since some warnings depend on the optimiser. Use -O2. Fortify adds warnings for unchecked I/O (among other things), which seems to be a good idea for user-space code. Enable that too. Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31tools/power x86_energy_perf_policy: Fix "uninitialized variable" warnings at -O2Ben Hutchings1-11/+15
x86_energy_perf_policy first uses __get_cpuid() to check the maximum CPUID level and exits if it is too low. It then assumes that later calls will succeed (which I think is architecturally guaranteed). It also assumes that CPUID works at all (which is not guaranteed on x86_32). If optimisations are enabled, gcc warns about potentially uninitialized variables. Fix this by adding an exit-on-error after every call to __get_cpuid() instead of just checking the maximum level. Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: Len Brown <[email protected]>
2019-08-31Merge branch 'i2c/for-current' of ↵Linus Torvalds7-14/+34
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: "I2C has a bunch of driver fixes and a core improvement to make the on-going API transition more robust" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: mediatek: disable zero-length transfers for mt8183 i2c: iproc: Stop advertising support of SMBUS quick cmd MAINTAINERS: i2c mv64xxx: Update documentation path i2c: piix4: Fix port selection for AMD Family 16h Model 30h i2c: designware: Synchronize IRQs when unregistering slave client i2c: i801: Avoid memory leak in check_acpi_smo88xx_device() i2c: make i2c_unregister_device() ERR_PTR safe
2019-08-31Merge tag 'trace-v5.3-rc6' of ↵Linus Torvalds6-15/+35
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing fixes from Steven Rostedt: "Small fixes and minor cleanups for tracing: - Make exported ftrace function not static - Fix NULL pointer dereference in reading probes as they are created - Fix NULL pointer dereference in k/uprobe clean up path - Various documentation fixes" * tag 'trace-v5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: tracing: Correct kdoc formats ftrace/x86: Remove mcount() declaration tracing/probe: Fix null pointer dereference tracing: Make exported ftrace_set_clr_event non-static ftrace: Check for successful allocation of hash ftrace: Check for empty hash and comment the race with registering probes ftrace: Fix NULL pointer dereference in t_probe_next()
2019-08-31Merge tag 'riscv/for-v5.3-rc7' of ↵Linus Torvalds2-6/+10
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V fix from Paul Walmsley: "One significant fix for 32-bit RISC-V systems: Fix the RV32 memory map to prevent userspace from corrupting the FIXMAP area. Without this patch, the system can crash very early during the boot" * tag 'riscv/for-v5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: RISC-V: Fix FIXMAP area corruption on RV32 systems
2019-08-31Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds6-16/+19
Pull KVM fixes from Radim Krčmář: "PPC: - Fix bug which could leave locks held in the host on return to a guest. x86: - Prevent infinitely looping emulation of a failing syscall while single stepping. - Do not crash the host when nesting is disabled" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: Don't update RIP or do single-step on faulting emulation KVM: x86: hyper-v: don't crash on KVM_GET_SUPPORTED_HV_CPUID when kvm_intel.nested is disabled KVM: PPC: Book3S: Fix incorrect guest-to-user-translation error handling
2019-08-31Merge branch 'akpm' (patches from Andrew)Linus Torvalds6-22/+47
Merge misc mm fixes from Andrew Morton: "7 fixes" * emailed patches from Andrew Morton <[email protected]>: mm: memcontrol: fix percpu vmstats and vmevents flush mm, memcg: do not set reclaim_state on soft limit reclaim mailmap: add aliases for Dmitry Safonov mm/z3fold.c: fix lock/unlock imbalance in z3fold_page_isolate mm, memcg: partially revert "mm/memcontrol.c: keep local VM counters in sync with the hierarchical ones" mm/zsmalloc.c: fix build when CONFIG_COMPACTION=n mm: memcontrol: flush percpu slab vmstats on kmem offlining
2019-08-31tracing: Correct kdoc formatsJakub Kicinski1-12/+14
Fix the following kdoc warnings: kernel/trace/trace.c:1579: warning: Function parameter or member 'tr' not described in 'update_max_tr_single' kernel/trace/trace.c:1579: warning: Function parameter or member 'tsk' not described in 'update_max_tr_single' kernel/trace/trace.c:1579: warning: Function parameter or member 'cpu' not described in 'update_max_tr_single' kernel/trace/trace.c:1776: warning: Function parameter or member 'type' not described in 'register_tracer' kernel/trace/trace.c:2239: warning: Function parameter or member 'task' not described in 'tracing_record_taskinfo' kernel/trace/trace.c:2239: warning: Function parameter or member 'flags' not described in 'tracing_record_taskinfo' kernel/trace/trace.c:2269: warning: Function parameter or member 'prev' not described in 'tracing_record_taskinfo_sched_switch' kernel/trace/trace.c:2269: warning: Function parameter or member 'next' not described in 'tracing_record_taskinfo_sched_switch' kernel/trace/trace.c:2269: warning: Function parameter or member 'flags' not described in 'tracing_record_taskinfo_sched_switch' kernel/trace/trace.c:3078: warning: Function parameter or member 'ip' not described in 'trace_vbprintk' kernel/trace/trace.c:3078: warning: Function parameter or member 'fmt' not described in 'trace_vbprintk' kernel/trace/trace.c:3078: warning: Function parameter or member 'args' not described in 'trace_vbprintk' Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Steven Rostedt (VMware) <[email protected]>
2019-08-31ftrace/x86: Remove mcount() declarationJisheng Zhang1-1/+0
Commit 562e14f72292 ("ftrace/x86: Remove mcount support") removed the support for using mcount, so we could remove the mcount() declaration to clean up. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Jisheng Zhang <[email protected]> Signed-off-by: Steven Rostedt (VMware) <[email protected]>
2019-08-31tracing/probe: Fix null pointer dereferenceXinpeng Liu1-1/+2
BUG: KASAN: null-ptr-deref in trace_probe_cleanup+0x8d/0xd0 Read of size 8 at addr 0000000000000000 by task syz-executor.0/9746 trace_probe_cleanup+0x8d/0xd0 free_trace_kprobe.part.14+0x15/0x50 alloc_trace_kprobe+0x23e/0x250 Link: http://lkml.kernel.org/r/[email protected] Fixes: e3dc9f898ef9c ("tracing/probe: Add trace_event_call accesses APIs") Signed-off-by: Xinpeng Liu <[email protected]> Signed-off-by: Steven Rostedt (VMware) <[email protected]>
2019-08-31tracing: Make exported ftrace_set_clr_event non-staticDenis Efremov2-1/+2
The function ftrace_set_clr_event is declared static and marked EXPORT_SYMBOL_GPL(), which is at best an odd combination. Because the function was decided to be a part of API, this commit removes the static attribute and adds the declaration to the header. Link: http://lkml.kernel.org/r/[email protected] Fixes: f45d1225adb04 ("tracing: Kernel access to Ftrace instances") Reviewed-by: Joe Jin <[email protected]> Signed-off-by: Denis Efremov <[email protected]> Signed-off-by: Steven Rostedt (VMware) <[email protected]>
2019-08-30Merge branch 'linus' of ↵Linus Torvalds1-0/+8
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 Pull crypto fix from Herbert Xu: "Fix a potential crash in the ccp driver" * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: ccp - Ignore unconfigured CCP device on suspend/resume
2019-08-30Partially revert "kfifo: fix kfifo_alloc() and kfifo_init()"Linus Torvalds1-1/+2
Commit dfe2a77fd243 ("kfifo: fix kfifo_alloc() and kfifo_init()") made the kfifo code round the number of elements up. That was good for __kfifo_alloc(), but it's actually wrong for __kfifo_init(). The difference? __kfifo_alloc() will allocate the rounded-up number of elements, but __kfifo_init() uses an allocation done by the caller. We can't just say "use more elements than the caller allocated", and have to round down. The good news? All the normal cases will be using power-of-two arrays anyway, and most users of kfifo's don't use kfifo_init() at all, but one of the helper macros to declare a KFIFO that enforce the proper power-of-two behavior. But it looks like at least ibmvscsis might be affected. The bad news? Will Deacon refers to an old thread and points points out that the memory ordering in kfifo's is questionable. See https://lore.kernel.org/lkml/[email protected]/ for more. Fixes: dfe2a77fd243 ("kfifo: fix kfifo_alloc() and kfifo_init()") Reported-by: laokz <[email protected]> Cc: Stefani Seibold <[email protected]> Cc: Andrew Morton <[email protected]> Cc: Dan Carpenter <[email protected]> Cc: Greg KH <[email protected]> Cc: Kees Cook <[email protected]> Cc: Will Deacon <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2019-08-30mm: memcontrol: fix percpu vmstats and vmevents flushShakeel Butt1-5/+5
Instead of using raw_cpu_read() use per_cpu() to read the actual data of the corresponding cpu otherwise we will be reading the data of the current cpu for the number of online CPUs. Link: http://lkml.kernel.org/r/[email protected] Fixes: bb65f89b7d3d ("mm: memcontrol: flush percpu vmevents before releasing memcg") Fixes: c350a99ea2b1 ("mm: memcontrol: flush percpu vmstats before releasing memcg") Signed-off-by: Shakeel Butt <[email protected]> Acked-by: Roman Gushchin <[email protected]> Acked-by: Michal Hocko <[email protected]> Cc: Johannes Weiner <[email protected]> Cc: Vladimir Davydov <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2019-08-30mm, memcg: do not set reclaim_state on soft limit reclaimMichal Hocko1-2/+3
Adric Blake has noticed[1] the following warning: WARNING: CPU: 7 PID: 175 at mm/vmscan.c:245 set_task_reclaim_state+0x1e/0x40 [...] Call Trace: mem_cgroup_shrink_node+0x9b/0x1d0 mem_cgroup_soft_limit_reclaim+0x10c/0x3a0 balance_pgdat+0x276/0x540 kswapd+0x200/0x3f0 ? wait_woken+0x80/0x80 kthread+0xfd/0x130 ? balance_pgdat+0x540/0x540 ? kthread_park+0x80/0x80 ret_from_fork+0x35/0x40 ---[ end trace 727343df67b2398a ]--- which tells us that soft limit reclaim is about to overwrite the reclaim_state configured up in the call chain (kswapd in this case but the direct reclaim is equally possible). This means that reclaim stats would get misleading once the soft reclaim returns and another reclaim is done. Fix the warning by dropping set_task_reclaim_state from the soft reclaim which is always called with reclaim_state set up. [1] http://lkml.kernel.org/r/CAE1jjeePxYPvw1mw2B3v803xHVR_BNnz0hQUY_JDMN8ny29M6w@mail.gmail.com Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Michal Hocko <[email protected]> Reported-by: Adric Blake <[email protected]> Acked-by: Yafang Shao <[email protected]> Acked-by: Yang Shi <[email protected]> Cc: Johannes Weiner <[email protected]> Cc: Hillf Danton <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2019-08-30mailmap: add aliases for Dmitry SafonovDmitry Safonov1-0/+3
I don't work for Virtuozzo or Samsung anymore and I've noticed that they have started sending annoying html email-replies. And I prioritize my personal emails over work email box, so while at it add an entry for Arista too - so I can reply faster when needed. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Dmitry Safonov <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2019-08-30mm/z3fold.c: fix lock/unlock imbalance in z3fold_page_isolateGustavo A. R. Silva1-0/+1
Fix lock/unlock imbalance by unlocking *zhdr* before return. Addresses Coverity ID 1452811 ("Missing unlock") Link: http://lkml.kernel.org/r/20190826030634.GA4379@embeddedor Fixes: d776aaa9895e ("mm/z3fold.c: fix race between migration and destruction") Signed-off-by: Gustavo A. R. Silva <[email protected]> Reviewed-by: Andrew Morton <[email protected]> Cc: Henry Burns <[email protected]> Cc: Vitaly Wool <[email protected]> Cc: Shakeel Butt <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2019-08-30mm, memcg: partially revert "mm/memcontrol.c: keep local VM counters in sync ↵Roman Gushchin1-5/+3
with the hierarchical ones" Commit 766a4c19d880 ("mm/memcontrol.c: keep local VM counters in sync with the hierarchical ones") effectively decreased the precision of per-memcg vmstats_local and per-memcg-per-node lruvec percpu counters. That's good for displaying in memory.stat, but brings a serious regression into the reclaim process. One issue I've discovered and debugged is the following: lruvec_lru_size() can return 0 instead of the actual number of pages in the lru list, preventing the kernel to reclaim last remaining pages. Result is yet another dying memory cgroups flooding. The opposite is also happening: scanning an empty lru list is the waste of cpu time. Also, inactive_list_is_low() can return incorrect values, preventing the active lru from being scanned and freed. It can fail both because the size of active and inactive lists are inaccurate, and because the number of workingset refaults isn't precise. In other words, the result is pretty random. I'm not sure, if using the approximate number of slab pages in count_shadow_number() is acceptable, but issues described above are enough to partially revert the patch. Let's keep per-memcg vmstat_local batched (they are only used for displaying stats to the userspace), but keep lruvec stats precise. This change fixes the dead memcg flooding on my setup. Link: http://lkml.kernel.org/r/[email protected] Fixes: 766a4c19d880 ("mm/memcontrol.c: keep local VM counters in sync with the hierarchical ones") Signed-off-by: Roman Gushchin <[email protected]> Acked-by: Yafang Shao <[email protected]> Cc: Johannes Weiner <[email protected]> Cc: Michal Hocko <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2019-08-30mm/zsmalloc.c: fix build when CONFIG_COMPACTION=nAndrew Morton1-0/+2
Fixes: 701d678599d0c1 ("mm/zsmalloc.c: fix race condition in zs_destroy_pool") Link: http://lkml.kernel.org/r/201908251039.5oSbEEUT%[email protected] Reported-by: kbuild test robot <[email protected]> Cc: Sergey Senozhatsky <[email protected]> Cc: Henry Burns <[email protected]> Cc: Minchan Kim <[email protected]> Cc: Shakeel Butt <[email protected]> Cc: Jonathan Adams <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2019-08-30mm: memcontrol: flush percpu slab vmstats on kmem offliningRoman Gushchin2-10/+30
I've noticed that the "slab" value in memory.stat is sometimes 0, even if some children memory cgroups have a non-zero "slab" value. The following investigation showed that this is the result of the kmem_cache reparenting in combination with the per-cpu batching of slab vmstats. At the offlining some vmstat value may leave in the percpu cache, not being propagated upwards by the cgroup hierarchy. It means that stats on ancestor levels are lower than actual. Later when slab pages are released, the precise number of pages is substracted on the parent level, making the value negative. We don't show negative values, 0 is printed instead. To fix this issue, let's flush percpu slab memcg and lruvec stats on memcg offlining. This guarantees that numbers on all ancestor levels are accurate and match the actual number of outstanding slab pages. Link: http://lkml.kernel.org/r/[email protected] Fixes: fb2f2b0adb98 ("mm: memcg/slab: reparent memcg kmem_caches on cgroup removal") Signed-off-by: Roman Gushchin <[email protected]> Cc: Johannes Weiner <[email protected]> Cc: Michal Hocko <[email protected]> Cc: Vladimir Davydov <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2019-08-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller5-7/+11
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for net: 1) Spurious warning when loading rules using the physdev match, from Todd Seidelmann. 2) Fix FTP conntrack helper debugging output, from Thomas Jarosch. 3) Restore per-netns nf_conntrack_{acct,helper,timeout} sysctl knobs, from Florian Westphal. 4) Clear skbuff timestamp from the flowtable datapath, also from Florian. 5) Fix incorrect byteorder of NFT_META_BRI_IIFVPROTO, from wenxu. ==================== Signed-off-by: David S. Miller <[email protected]>
2019-08-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller2-6/+19
Daniel Borkmann says: ==================== pull-request: bpf 2019-08-31 The following pull-request contains BPF updates for your *net* tree. The main changes are: 1) Fix 32-bit zero-extension during constant blinding which has been causing a regression on ppc64, from Naveen. 2) Fix a latency bug in nfp driver when updating stack index register, from Jiong. ==================== Signed-off-by: David S. Miller <[email protected]>
2019-08-30rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]David Howells5-5/+50
When a local endpoint is ceases to be in use, such as when the kafs module is unloaded, the kernel will emit an assertion failure if there are any outstanding client connections: rxrpc: Assertion failed ------------[ cut here ]------------ kernel BUG at net/rxrpc/local_object.c:433! and even beyond that, will evince other oopses if there are service connections still present. Fix this by: (1) Removing the triggering of connection reaping when an rxrpc socket is released. These don't actually clean up the connections anyway - and further, the local endpoint may still be in use through another socket. (2) Mark the local endpoint as dead when we start the process of tearing it down. (3) When destroying a local endpoint, strip all of its client connections from the idle list and discard the ref on each that the list was holding. (4) When destroying a local endpoint, call the service connection reaper directly (rather than through a workqueue) to immediately kill off all outstanding service connections. (5) Make the service connection reaper reap connections for which the local endpoint is marked dead. Only after destroying the connections can we close the socket lest we get an oops in a workqueue that's looking at a connection or a peer. Fixes: 3d18cbb7fd0c ("rxrpc: Fix conn expiry timers") Signed-off-by: David Howells <[email protected]> Tested-by: Marc Dionne <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.