| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When it gets set, End Of Queue Flag halts the DSPI controller and forces
the chip select signal to deassert.
This operating mode is not ideal, but it is used for the DSPI
instantiations where there is no other notification from the controller
that the data in the FIFO has finished transmission. So in practice, it
means that transmitting buffers larger than the FIFO size will yield
unpredictable results.
The only controller that operates in EOQ mode is MCF5441X (Coldfire). I
would say that the way EOQ is used (and documented in the reference
manual, too) on this chip is incorrect, and I would personally migrate
it to TCFQ, but that's notably worse in terms of performance (it can
only use 1 entry of the 16-deep FIFO) and if this limitation didn't
bother any Coldfire DSPI user so far, it's likely that we just need to
throw an error for larger buffers to make sure that callers are aware
their transfers are getting truncated/split.
Signed-off-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
These function names are very generic and it is easy to get confused.
Rename them after the hardware register that they are accessing.
Signed-off-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Their names are confusing, since dspi_pop_tx prepares a word to be
written to the PUSHR register, and dspi_push_rx gets a word from the
POPR register.
Signed-off-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This is a useless operation, and if the driver needs to do that, there's
something deeply wrong going on.
Signed-off-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This variable has been present since the initial submission of the
driver, and held, for some reason, the value of zero, to be sent on the
wire in the case there wasn't any TX buffer for the current transfer.
Since quite a while now, however, it isn't doing anything at all.
Signed-off-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Reduce the if-then-else-if-then-else sequence to:
- a simple division in the case of bytes_per_word calculation
- a memcpy command with a variable size. The semantics of larger-than-8
xfer->bits_per_word is that those words are to be interpreted and
transmitted in CPU native endianness.
Signed-off-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Vladimir Oltean <[email protected]>:
This series makes room in the driver for differentiation between the
controllers which currently operate in TCFQ mode. Most of these are
actually capable of a lot more in terms of throughput. This is in
preparation of a second series which will convert the remaining users of
TCFQ mode altogether to XSPI mode with command cycling.
Vladimir Oltean (6):
doc: spi-fsl-dspi: Add specific compatibles for all Layerscape SoCs
spi: spi-fsl-dspi: Use specific compatible strings for all SoC
instantiations
spi: spi-fsl-dspi: Parameterize the FIFO size and DMA buffer size
spi: spi-fsl-dspi: LS2080A and LX2160A support XSPI mode
spi: spi-fsl-dspi: Support SPI software timestamping in all non-DMA
modes
spi: spi-fsl-dspi: Convert the instantiations that support it to DMA
.../devicetree/bindings/spi/spi-fsl-dspi.txt | 17 +-
drivers/spi/spi-fsl-dspi.c | 162 +++++++++++++-----
2 files changed, 128 insertions(+), 51 deletions(-)
--
2.17.1
|
|
Make the second compatible string optional for LS1012A, LS1088A and
LS2080A. Old versions of the spi-fsl-dspi.c driver still need to probe
on the old, generic compatible string for these controllers (such as
"fsl,ls1021a-v1.0-dspi") which provides less functionality.
Document the device tree bindings for LS1043A and LS1046A, whose
bindings are already in use in fsl-ls1043a.dtsi and fsl-ls1046a.dtsi.
Introduce new compatible strings for LS1028A and LX2160A. There will be
no second compatible string for these.
Signed-off-by: Vladimir Oltean <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
The A-011218 eDMA/DSPI erratum affects most of the older Layerscape SoCs
with DSPI, and its workaround is a bit intrusive.
After this patch, there are no users of TCFQ mode that don't also
support XSPI (previously there was LS2085A).
Signed-off-by: Vladimir Oltean <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
There's no reason to keep this .ptp_sts_supported property explicitly in
devtype_data, since it can be deduced from the operating mode alone.
Signed-off-by: Vladimir Oltean <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
XSPI allows for 2 extra features:
- Command cycling (use a single TX command with more than 1 word in the
TX FIFO).
- Increased word size (from 16 bits to 32 bits)
Signed-off-by: Vladimir Oltean <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
Get rid of the ifdef for Coldfire and make these hardware
characteristics part of dspi->devtype_data.
Signed-off-by: Vladimir Oltean <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
Currently, the device tree bindings submitted in mainline for Layerscape
SoCs look like this:
LS1021A:
compatible = "fsl,ls1021a-v1.0-dspi";
LS1012A:
compatible = "fsl,ls1012a-dspi", "fsl,ls1021a-v1.0-dspi";
LS2085A:
compatible = "fsl,ls2085a-dspi";
LS2088A:
compatible = "fsl,ls2080a-dspi", "fsl,ls2085a-dspi";
LX2160A:
compatible = "fsl,lx2160a-dspi", "fsl,ls2085a-dspi";
LS1043A:
compatible = "fsl,ls1043a-dspi", "fsl,ls1021a-v1.0-dspi";
LS1046A:
compatible = "fsl,ls1021a-v1.0-dspi";
Due to a lack of a more specific compatible string, LS1012A, LS1043A and
LS1046A will fall under the LS1021A umbrella, and LS2088A and LX2160A
under the LS2085A umbrella.
They do work in those modes, but there are slight differences in the
hardware instantiations, mostly related to FIFO sizes (with the more
specific compatible strings, the FIFO size can be increased properly).
Signed-off-by: Vladimir Oltean <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
Pull cifs fixes from Steve French:
"Five small cifs/smb3 fixes, two for stable (one for a reconnect
problem and the other fixes a use case when renaming an open file)"
* tag '5.6-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Use #define in cifs_dbg
cifs: fix rename() by ensuring source handle opened with DELETE bit
cifs: add missing mount option to /proc/mounts
cifs: fix potential mismatch of UNC paths
cifs: don't leak -EAGAIN for stat() during reconnect
|
|
<[email protected]>:
- the memory optimization in fsl-spi
- the fix of the max speed setting bug in spidev
Oleksandr Suvorov (2):
spi: fsl-lpspi: remove unneeded array
spi: spidev: fix a max speed setting
drivers/spi/spi-fsl-lpspi.c | 7 ++-----
drivers/spi/spidev.c | 10 ++++++----
2 files changed, 8 insertions(+), 9 deletions(-)
--
2.24.1
|
|
- replace the array with the shift operation
- remove the extra comparing operation.
Signed-off-by: Oleksandr Suvorov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
devm_regulator_register() could return -EPROBE_DEFER when trying to
get init data and NOT all resources are available at that time, for
this case, error message is better to be present for debug level ONLY.
Signed-off-by: Anson Huang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
<[email protected]>:
- fix the values source for the xfer debug message.
- fix the "max speed setting" message showing.
Oleksandr Suvorov (2):
spi: spidev: fix a debug message value
spi: spidev: fix speed setting message
drivers/spi/spidev.c | 23 ++++++++++++-----------
1 file changed, 12 insertions(+), 11 deletions(-)
--
2.24.1
|
|
The message of max device speed setting is shown when
an error in spi_setup() occurs.
Instead, it should be shown when the setup call succeeds.
Signed-off-by: Oleksandr Suvorov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The debug message in spidev_message() can show wrong xfer speed.
It happens if the initial (came from DT) and set with ioctl call spidev
speeds are different (spidev->speed_hz != spi->max_speed_hz) and one
sends a message with ioctl call and the field of speed is uninitialized
(u_tmp->speed_hz == 0).
In this case the kernel shows the spi->max_speed_hz value instead of
correct spidev->speed_hz.
...
set the max speed with an ioctl call:
[ 1227.702714] spidev spi0.0: setup mode 0, 32 bits/w, 20000000 Hz max --> 0
(real speed sets to 20000000Hz)
send a message with an ioctl call:
[ 1227.731801] spidev spi0.0: xfer len 4096 tx 32bits 0 usec 10000000Hz
(debug message shows 10000000Hz that is the original max speed of this
spidev came from DT)
...
Fix the data source for the debug message.
Signed-off-by: Oleksandr Suvorov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The purpose of commit 0fd85869c2a9 ("spi/bcm63xx-hsspi: keep pll clk enabled")
was to keep the pll clk enabled through the lifetime of the device.
In order to do that, some 'clk_prepare_enable()'/'clk_disable_unprepare()'
calls have been added in the error handling path of the probe function, in
the remove function and in the suspend and resume functions.
However, a 'clk_disable_unprepare()' call has been unfortunately left in
the probe function. So the commit seems to be more or less a no-op.
Axe it now, so that the pll clk is left enabled through the lifetime of
the device, as described in the commit.
Fixes: 0fd85869c2a9 ("spi/bcm63xx-hsspi: keep pll clk enabled")
Signed-off-by: Christophe JAILLET <[email protected]>
Acked-by: Jonas Gorski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Deferred probe is an expected return value for devm_pwm_get(). Given
that the driver deals with it properly, rather than warn on probe
deferral, only output a message on probe deferral if debug level
prints are enabled.
Signed-off-by: Jon Hunter <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
ANATOP regulator should depend on ARCH_MXC or COMPILE_TEST.
Signed-off-by: Anson Huang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes: a pkeys fix for a bug that triggers with weird BIOS
settings, and two Xen PV fixes: a paravirt interface fix, and
pagetable dumping fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix dump_pagetables with Xen PV
x86/ioperm: Add new paravirt function update_io_bitmap()
x86/pkeys: Manually set X86_FEATURE_OSPKE to preserve existing changes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix a scheduler statistics bug"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix statistics for find_idlest_group()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"No kernel side changes, all tooling fixes plus two tooling cleanups
that were committed late in the merge window alongside the perf
annotate fixes, delayed by Arnaldo's European trip"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
perf annotate: Fix segfault with source toggle
perf annotate: Align struct annotate_args
perf annotate: Simplify disasm_line allocation and freeing code
perf annotate: Remove privsize from symbol__annotate() args
perf probe: Check return value of strlist__add() for -ENOMEM
perf config: Document missing config options
perf annotate: Fix perf config option description
perf annotate: Prefer cmdline option over default config
perf annotate: Make perf config effective
perf config: Introduce perf_config_u8()
perf annotate: Fix --show-nr-samples for tui/stdio2
perf annotate: Fix --show-total-period for tui/stdio2
perf annotate/tui: Re-render title bar after switching back from script browser
tools headers UAPI: Update tools's copy of kvm.h headers
tools arch x86: Sync the msr-index.h copy with the kernel sources
perf arch powerpc: Sync powerpc syscall.tbl with the kernel sources
perf auxtrace: Add auxtrace_record__read_finish()
perf arm-spe: Fix endless record after being terminated
perf cs-etm: Fix endless record after being terminated
perf intel-bts: Fix endless record after being terminated
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Three fixes to EFI mixed boot mode, mostly related to x86-64 vmap
stacks activated years ago, bug-fixed recently for EFI, which had
knock-on effects of various 1:1 mapping assumptions in mixed mode.
There's also a READ_ONCE() fix for reading an mmap-ed EFI firmware
data field only once, out of caution"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: READ_ONCE rng seed size before munmap
efi/x86: Handle by-ref arguments covering multiple pages in mixed mode
efi/x86: Remove support for EFI time and counter services in mixed mode
efi/x86: Align GUIDs to their size in the mixed mode runtime wrapper
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Two more bug fixes (including a regression) for 5.6"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: potential crash on allocation error in ext4_alloc_flex_bg_array()
jbd2: fix data races at struct journal_head
|
|
Pull KVM fixes from Paolo Bonzini:
"More bugfixes, including a few remaining "make W=1" issues such as too
large frame sizes on some configurations.
On the ARM side, the compiler was messing up shadow stacks between EL1
and EL2 code, which is easily fixed with __always_inline"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: check descriptor table exits on instruction emulation
kvm: x86: Limit the number of "kvm: disabled by bios" messages
KVM: x86: avoid useless copy of cpufreq policy
KVM: allow disabling -Werror
KVM: x86: allow compiling as non-module with W=1
KVM: Pre-allocate 1 cpumask variable per cpu for both pv tlb and pv ipis
KVM: Introduce pv check helpers
KVM: let declaration of kvm_get_running_vcpus match implementation
KVM: SVM: allocate AVIC data structures based on kvm_amd module parameter
arm64: Ask the compiler to __always_inline functions used by KVM at HYP
KVM: arm64: Define our own swab32() to avoid a uapi static inline
KVM: arm64: Ask the compiler to __always_inline functions used at HYP
kvm: arm/arm64: Fold VHE entry/exit work into kvm_vcpu_run_vhe()
KVM: arm/arm64: Fix up includes for trace.h
|
|
KVM emulates UMIP on hardware that doesn't support it by setting the
'descriptor table exiting' VM-execution control and performing
instruction emulation. When running nested, this emulation is broken as
KVM refuses to emulate L2 instructions by default.
Correct this regression by allowing the emulation of descriptor table
instructions if L1 hasn't requested 'descriptor table exiting'.
Fixes: 07721feee46b ("KVM: nVMX: Don't emulate instructions in guest mode")
Reported-by: Jan Kiszka <[email protected]>
Cc: [email protected]
Cc: Paolo Bonzini <[email protected]>
Cc: Jim Mattson <[email protected]>
Signed-off-by: Oliver Upton <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has three driver bugfixes for you. We agreed on the Mac regression
to go in via I2C"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
macintosh: therm_windtunnel: fix regression when instantiating devices
i2c: altera: Fix potential integer overflow
i2c: jz4780: silence log flood on txabrt
|
|
If sbi->s_flex_groups_allocated is zero and the first allocation fails
then this code will crash. The problem is that "i--" will set "i" to
-1 but when we compare "i >= sbi->s_flex_groups_allocated" then the -1
is type promoted to unsigned and becomes UINT_MAX. Since UINT_MAX
is more than zero, the condition is true so we call kvfree(new_groups[-1]).
The loop will carry on freeing invalid memory until it crashes.
Fixes: 7c990728b99e ("ext4: fix potential race between s_flex_groups online resizing and access")
Reviewed-by: Suraj Jitindar Singh <[email protected]>
Signed-off-by: Dan Carpenter <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
Removing attach_adapter from this driver caused a regression for at
least some machines. Those machines had the sensors described in their
DT, too, so they didn't need manual creation of the sensor devices. The
old code worked, though, because manual creation came first. Creation of
DT devices then failed later and caused error logs, but the sensors
worked nonetheless because of the manually created devices.
When removing attach_adaper, manual creation now comes later and loses
the race. The sensor devices were already registered via DT, yet with
another binding, so the driver could not be bound to it.
This fix refactors the code to remove the race and only manually creates
devices if there are no DT nodes present. Also, the DT binding is updated
to match both, the DT and manually created devices. Because we don't
know which device creation will be used at runtime, the code to start
the kthread is moved to do_probe() which will be called by both methods.
Fixes: 3e7bed52719d ("macintosh: therm_windtunnel: drop using attach_adapter")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201723
Reported-by: Erhard Furtner <[email protected]>
Tested-by: Erhard Furtner <[email protected]>
Acked-by: Michael Ellerman <[email protected]> (powerpc)
Signed-off-by: Wolfram Sang <[email protected]>
Cc: [email protected] # v4.19+
|
|
journal_head::b_transaction and journal_head::b_next_transaction could
be accessed concurrently as noticed by KCSAN,
LTP: starting fsync04
/dev/zero: Can't open blockdev
EXT4-fs (loop0): mounting ext3 file system using the ext4 subsystem
EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
==================================================================
BUG: KCSAN: data-race in __jbd2_journal_refile_buffer [jbd2] / jbd2_write_access_granted [jbd2]
write to 0xffff99f9b1bd0e30 of 8 bytes by task 25721 on cpu 70:
__jbd2_journal_refile_buffer+0xdd/0x210 [jbd2]
__jbd2_journal_refile_buffer at fs/jbd2/transaction.c:2569
jbd2_journal_commit_transaction+0x2d15/0x3f20 [jbd2]
(inlined by) jbd2_journal_commit_transaction at fs/jbd2/commit.c:1034
kjournald2+0x13b/0x450 [jbd2]
kthread+0x1cd/0x1f0
ret_from_fork+0x27/0x50
read to 0xffff99f9b1bd0e30 of 8 bytes by task 25724 on cpu 68:
jbd2_write_access_granted+0x1b2/0x250 [jbd2]
jbd2_write_access_granted at fs/jbd2/transaction.c:1155
jbd2_journal_get_write_access+0x2c/0x60 [jbd2]
__ext4_journal_get_write_access+0x50/0x90 [ext4]
ext4_mb_mark_diskspace_used+0x158/0x620 [ext4]
ext4_mb_new_blocks+0x54f/0xca0 [ext4]
ext4_ind_map_blocks+0xc79/0x1b40 [ext4]
ext4_map_blocks+0x3b4/0x950 [ext4]
_ext4_get_block+0xfc/0x270 [ext4]
ext4_get_block+0x3b/0x50 [ext4]
__block_write_begin_int+0x22e/0xae0
__block_write_begin+0x39/0x50
ext4_write_begin+0x388/0xb50 [ext4]
generic_perform_write+0x15d/0x290
ext4_buffered_write_iter+0x11f/0x210 [ext4]
ext4_file_write_iter+0xce/0x9e0 [ext4]
new_sync_write+0x29c/0x3b0
__vfs_write+0x92/0xa0
vfs_write+0x103/0x260
ksys_write+0x9d/0x130
__x64_sys_write+0x4c/0x60
do_syscall_64+0x91/0xb05
entry_SYSCALL_64_after_hwframe+0x49/0xbe
5 locks held by fsync04/25724:
#0: ffff99f9911093f8 (sb_writers#13){.+.+}, at: vfs_write+0x21c/0x260
#1: ffff99f9db4c0348 (&sb->s_type->i_mutex_key#15){+.+.}, at: ext4_buffered_write_iter+0x65/0x210 [ext4]
#2: ffff99f5e7dfcf58 (jbd2_handle){++++}, at: start_this_handle+0x1c1/0x9d0 [jbd2]
#3: ffff99f9db4c0168 (&ei->i_data_sem){++++}, at: ext4_map_blocks+0x176/0x950 [ext4]
#4: ffffffff99086b40 (rcu_read_lock){....}, at: jbd2_write_access_granted+0x4e/0x250 [jbd2]
irq event stamp: 1407125
hardirqs last enabled at (1407125): [<ffffffff980da9b7>] __find_get_block+0x107/0x790
hardirqs last disabled at (1407124): [<ffffffff980da8f9>] __find_get_block+0x49/0x790
softirqs last enabled at (1405528): [<ffffffff98a0034c>] __do_softirq+0x34c/0x57c
softirqs last disabled at (1405521): [<ffffffff97cc67a2>] irq_exit+0xa2/0xc0
Reported by Kernel Concurrency Sanitizer on:
CPU: 68 PID: 25724 Comm: fsync04 Tainted: G L 5.6.0-rc2-next-20200221+ #7
Hardware name: HPE ProLiant DL385 Gen10/ProLiant DL385 Gen10, BIOS A40 07/10/2019
The plain reads are outside of jh->b_state_lock critical section which result
in data races. Fix them by adding pairs of READ|WRITE_ONCE().
Reviewed-by: Jan Kara <[email protected]>
Signed-off-by: Qian Cai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes.
Three are in drivers for fairly obvious bugs. The fourth is a set of
regressions introduced by the compat_ioctl changes because some of the
compat updates wrongly replaced .ioctl instead of .compat_ioctl"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: compat_ioctl: cdrom: Replace .ioctl with .compat_ioctl in four appropriate places
scsi: zfcp: fix wrong data and display format of SFP+ temperature
scsi: sd_sbc: Fix sd_zbc_report_zones()
scsi: libfc: free response frame from GPN_ID
|
|
Commit 2ae27137b2db89 ("x86: mm: convert dump_pagetables to use
walk_page_range") broke Xen PV guests as the hypervisor reserved hole in
the memory map was not taken into account.
Fix that by starting the kernel range only at GUARD_HOLE_END_ADDR.
Fixes: 2ae27137b2db89 ("x86: mm: convert dump_pagetables to use walk_page_range")
Reported-by: Julien Grall <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Tested-by: Julien Grall <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
Commit 111e7b15cf10f6 ("x86/ioperm: Extend IOPL config to control ioperm()
as well") reworked the iopl syscall to use I/O bitmaps.
Unfortunately this broke Xen PV domains using that syscall as there is
currently no I/O bitmap support in PV domains.
Add I/O bitmap support via a new paravirt function update_io_bitmap which
Xen PV domains can use to update their I/O bitmaps via a hypercall.
Fixes: 111e7b15cf10f6 ("x86/ioperm: Extend IOPL config to control ioperm() as well")
Reported-by: Jan Beulich <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Tested-by: Jan Beulich <[email protected]>
Reviewed-by: Jan Beulich <[email protected]>
Cc: <[email protected]> # 5.5
Link: https://lkml.kernel.org/r/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
perf annotate:
Ravi Bangoria:
- Fix segfault with source toggle.
- Fix --show-total-period and --show-nr-samples for tui/stdio2.
- Fix handling of settings in ~/.perfconfig versus the ones passed
in the command line
- Re-render title bar after switching back from script browser.
- Fix options man page, document some missing ones.
perf probe:
He Zhe:
- Check return value of strlist__add() for -ENOMEM.
tools UAPI:
Arnaldo Carvalho de Melo:
- Sync x86's msr-index.h copy with the kernel sources.
- Update tools's copy of x86's kvm.h headers.
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix build issue on 32-bit ARM with old compilers (Marek Szyprowski)
- Update MAINTAINERS for recent Cadence driver file move (Lukas
Bulwahn)
* tag 'pci-v5.6-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Correct Cadence PCI driver path
PCI: brcmstb: Fix build on 32bit ARM platforms with older compilers
|
|
Pull block fixes from Jens Axboe:
- Passthrough insertion fix (Ming)
- Kill off some unused arguments (John)
- blktrace RCU fix (Jan)
- Dead fields removal for null_blk (Dongli)
- NVMe polled IO fix (Bijan)
* tag 'block-5.6-2020-02-28' of git://git.kernel.dk/linux-block:
nvme-pci: Hold cq_poll_lock while completing CQEs
blk-mq: Remove some unused function arguments
null_blk: remove unused fields in 'nullb_cmd'
blktrace: Protect q->blk_trace with RCU
blk-mq: insert passthrough request into hctx->dispatch directly
|
|
Pull io_uring fixes from Jens Axboe:
- Fix for a race with IOPOLL used with SQPOLL (Xiaoguang)
- Only show ->fdinfo if procfs is enabled (Tobias)
- Fix for a chain with multiple personalities in the SQEs
- Fix for a missing free of personality idr on exit
- Removal of the spin-for-work optimization
- Fix for next work lookup on request completion
- Fix for non-vec read/write result progation in case of links
- Fix for a fileset references on switch
- Fix for a recvmsg/sendmsg 32-bit compatability mode
* tag 'io_uring-5.6-2020-02-28' of git://git.kernel.dk/linux-block:
io_uring: fix 32-bit compatability with sendmsg/recvmsg
io_uring: define and set show_fdinfo only if procfs is enabled
io_uring: drop file set ref put/get on switch
io_uring: import_single_range() returns 0/-ERROR
io_uring: pick up link work on submit reference drop
io-wq: ensure work->task_pid is cleared on init
io-wq: remove spin-for-work optimization
io_uring: fix poll_list race for SETUP_IOPOLL|SETUP_SQPOLL
io_uring: fix personality idr leak
io_uring: handle multiple personalities in link chains
|
|
Introduce is_mmp2_ssp() helper to be consistent with the rest
helper function to distinguish SSP type.
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
quirks" from John Garry <[email protected]>:
As discussed during the original HiSilicon v3xx SPI driver upstreaming,
currently there is no method for the ACPI SPI Serial Bus Connection
Resource Descriptor to define the data buswidth [0], [1].
So we can look to get the ACPI spec updated for this, and I have
submitted a proposal for a new feature here:
https://bugzilla.tianocore.org/show_bug.cgi?id=2557
However I am not sure how successful that will be.
In the meantime, as an alternate approach, this RFC proposes to allow the
SPI controller driver override the device buswidth. In this example,
the driver uses DMI quirks to discover the host machine and set the
buswidth override accordingly when the machine is known to support
dual or quad mode of operation.
I also have included a fix for dual and quad modes in the driver.
Comments welcome. thanks.
[0] https://lore.kernel.org/linux-mtd/[email protected]/
[1] https://uefi.org/sites/default/files/resources/ACPI_6_3_final_Jan30.pdf,
19.6.126
John Garry (3):
spi: Allow SPI controller override device buswidth
spi: HiSilicon v3xx: Properly set CMD_CONFIG for Dual/Quad modes
spi: HiSilicon v3xx: Use DMI quirk to set controller buswidth override
bits
drivers/spi/spi-hisi-sfc-v3xx.c | 99 ++++++++++++++++++++++++++++++++-
drivers/spi/spi.c | 4 +-
include/linux/spi/spi.h | 3 +
3 files changed, 104 insertions(+), 2 deletions(-)
--
2.17.1
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
|
|
When adjust_op_size is defined, len is never used. Move the len
computation where it's actually used.
Signed-off-by: Tudor Ambarus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The Huawei D06 board (and variants) can support Quad mode of operation.
Since we have no current method in ACPI SPI bus device resource description
to describe this information, use DMI to detect the board, and set the
controller buswidth override bits.
Signed-off-by: John Garry <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The CMD_CONFIG register memory interface type field is not set configured
for Dual and Quad modes, so set appropriately.
This was not detected previously as we only ever operated in standard SPI
mode.
Signed-off-by: John Garry <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Currently ACPI firmware description for a SPI device does not have any
method to describe the data buswidth on the board.
So even through the controller and device may support higher modes than
standard SPI, it cannot be assumed that the board does - as such, that
device is limited to standard SPI in such a circumstance.
As a workaround, allow the controller driver supply buswidth override bits,
which are used inform the core code that the controller driver knows the
buswidth supported on that board for that device.
A host controller driver might know this info from DMI tables, for example.
Signed-off-by: John Garry <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The QSPI controller memory space is limited to 128MB:
0x9000_00000-0x9800_00000/0XD000_0000--0XD800_0000.
There are nor flashes that are bigger in size than the memory size
supported by the controller: Micron MT25QL02G (256 MB).
Check if the address exceeds the MMIO window size. An improvement
would be to add support for regular SPI mode and fall back to it
when the flash memories overrun the controller's memory space.
Fixes: 0e6aae08e9ae ("spi: Add QuadSPI driver for Atmel SAMA5D2")
Signed-off-by: Tudor Ambarus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Pull NVMe fix from Keith.
* 'nvme-5.6-rc4' of git://git.infradead.org/nvme:
nvme-pci: Hold cq_poll_lock while completing CQEs
|