| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Running TCRYPT with LRW compiled causes spinlock recursion:
testing speed of async lrw(aes) (lrw(ecb-aes-s5p)) encryption
tcrypt: test 0 (256 bit key, 16 byte blocks): 19007 operations in 1 seconds (304112 bytes)
tcrypt: test 1 (256 bit key, 64 byte blocks): 15753 operations in 1 seconds (1008192 bytes)
tcrypt: test 2 (256 bit key, 256 byte blocks): 14293 operations in 1 seconds (3659008 bytes)
tcrypt: test 3 (256 bit key, 1024 byte blocks): 11906 operations in 1 seconds (12191744 bytes)
tcrypt: test 4 (256 bit key, 8192 byte blocks):
BUG: spinlock recursion on CPU#1, irq/84-10830000/89
lock: 0xeea99a68, .magic: dead4ead, .owner: irq/84-10830000/89, .owner_cpu: 1
CPU: 1 PID: 89 Comm: irq/84-10830000 Not tainted 4.11.0-rc1-00001-g897ca6d0800d #559
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c010e1ec>] (unwind_backtrace) from [<c010ae1c>] (show_stack+0x10/0x14)
[<c010ae1c>] (show_stack) from [<c03449c0>] (dump_stack+0x78/0x8c)
[<c03449c0>] (dump_stack) from [<c015de68>] (do_raw_spin_lock+0x11c/0x120)
[<c015de68>] (do_raw_spin_lock) from [<c0720110>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c0720110>] (_raw_spin_lock_irqsave) from [<c0572ca0>] (s5p_aes_crypt+0x2c/0xb4)
[<c0572ca0>] (s5p_aes_crypt) from [<bf1d8aa4>] (do_encrypt+0x78/0xb0 [lrw])
[<bf1d8aa4>] (do_encrypt [lrw]) from [<bf1d8b00>] (encrypt_done+0x24/0x54 [lrw])
[<bf1d8b00>] (encrypt_done [lrw]) from [<c05732a0>] (s5p_aes_complete+0x60/0xcc)
[<c05732a0>] (s5p_aes_complete) from [<c0573440>] (s5p_aes_interrupt+0x134/0x1a0)
[<c0573440>] (s5p_aes_interrupt) from [<c01667c4>] (irq_thread_fn+0x1c/0x54)
[<c01667c4>] (irq_thread_fn) from [<c0166a98>] (irq_thread+0x12c/0x1e0)
[<c0166a98>] (irq_thread) from [<c0136a28>] (kthread+0x108/0x138)
[<c0136a28>] (kthread) from [<c0107778>] (ret_from_fork+0x14/0x3c)
Interrupt handling routine was calling req->base.complete() under
spinlock. In most cases this wasn't fatal but when combined with some
of the cipher modes (like LRW) this caused recursion - starting the new
encryption (s5p_aes_crypt()) while still holding the spinlock from
previous round (s5p_aes_complete()).
Beside that, the s5p_aes_interrupt() error handling path could execute
two completions in case of error for RX and TX blocks.
Rewrite the interrupt handling routine and the completion by:
1. Splitting the operations on scatterlist copies from
s5p_aes_complete() into separate s5p_sg_done(). This still should be
done under lock.
The s5p_aes_complete() now only calls req->base.complete() and it has
to be called outside of lock.
2. Moving the s5p_aes_complete() out of spinlock critical sections.
In interrupt service routine s5p_aes_interrupts(), it appeared in few
places, including error paths inside other functions called from ISR.
This code was not so obvious to read so simplify it by putting the
s5p_aes_complete() only within ISR level.
Reported-by: Nathan Royce <[email protected]>
Cc: <[email protected]> # v4.10.x: 07de4bc88c crypto: s5p-sss - Fix completing
Cc: <[email protected]> # v4.10.x
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.11-rc2
Here's a fix for a digi_acceleport regression in -rc1, and some fixes
for long-standing issues in three other drivers, including a
NULL-pointer dereference and a couple of information leaks that could be
triggered by a malicious device.
Signed-off-by: Johan Hovold <[email protected]>
|
|
A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.
Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <[email protected]>
Fixes: 2d380889215f ("USB: serial: digi_acceleport: fix OOB data sanity check")
Cc: stable <[email protected]> # v2.6.30
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The platform_data header file was dropped in the merged version of the
USB251xB driver. Therefore remove its reference from the MAINTAINERS file.
Signed-off-by: Richard Leitner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Mark the reg property as required and furthermore fix some typos and
spellings in the documentation.
Signed-off-by: Richard Leitner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Rename oc-delay-* to oc-delay-us and make it expect a time value.
Furthermore add -ms suffix to power-on-time. There changes were
suggested by Rob Herring in https://lkml.org/lkml/2017/2/15/1283.
Signed-off-by: Richard Leitner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Remove the max_{power,current}_{sp,bp} properties of the usb251xb driver
from devicetree. This is done to simplify the dt bindings as requested
by Rob Herring in https://lkml.org/lkml/2017/2/15/1283. If those
properties are ever needed by somebody they can be enabled again easily.
Signed-off-by: Richard Leitner <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This USB-SATA bridge chip is used in a StarTech enclosure for
optical drives.
Without the quirk MakeMKV fails during the key exchange with an
installed BluRay drive:
> Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED'
> occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:2'
Signed-off-by: Tobias Jakobi <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Make sure to verify that we have the required interrupt-out endpoint for
IOWarrior56 devices to avoid dereferencing a NULL-pointer in write
should a malicious device lack such an endpoint.
Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.")
Cc: stable <[email protected]> # 2.6.21
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Make sure to check for the required interrupt-in endpoint to avoid
dereferencing a NULL-pointer should a malicious device lack such an
endpoint.
Note that a fairly recent change purported to fix this issue, but added
an insufficient test on the number of endpoints only, a test which can
now be removed.
Fixes: 4ec0ef3a8212 ("USB: iowarrior: fix oops with malicious USB descriptors")
Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.")
Cc: stable <[email protected]> # 2.6.21
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In patch 2e2aa1bc7eff90ecm, USB suspend and wakeup control requests are
passed to SFR_OHCIICR register. If a processor does not have such a
register, this hub control request will be dropped.
If no such a SFR register is available, all USB suspend control requests
will now be processed using ohci_hub_control()
(like before patch 2e2aa1bc7eff90ecm.)
Tested on an Atmel AT91SAM9G20 with an on-board TI TUSB2046B hub chip
If the last USB device is unplugged from the USB hub, the hub goes into
sleep and will not wakeup when an USB devices is inserted.
Fixes: 2e2aa1bc7eff90ec ("usb: ohci-at91: Forcibly suspend ports while USB suspend")
Signed-off-by: Jelle Martijn Kok <[email protected]>
Tested-by: Wenyou Yang <[email protected]>
Cc: Wenyou Yang <[email protected]>
Cc: Alan Stern <[email protected]>
Cc: stable <[email protected]>
Acked-by: Nicolas Ferre <[email protected]>
Reviewed-by: Alexandre Belloni <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
On POWERNV platform, in order to do DMA via IOMMU (i.e. 32bit DMA in
our case), a device needs an iommu_table pointer set via
set_iommu_table_base().
The codeflow is:
- pnv_pci_ioda2_setup_dma_pe()
- pnv_pci_ioda2_setup_default_config()
- pnv_ioda_setup_bus_dma() [1]
pnv_pci_ioda2_setup_dma_pe() creates IOMMU groups,
pnv_pci_ioda2_setup_default_config() does default DMA setup,
pnv_ioda_setup_bus_dma() takes a bus PE (on IODA2, all physical function
PEs as bus PEs except NPU), walks through all underlying buses and
devices, adds all devices to an IOMMU group and sets iommu_table.
On IODA2, when VFIO is used, it takes ownership over a PE which means it
removes all tables and creates new ones (with a possibility of sharing
them among PEs). So when the ownership is returned from VFIO to
the kernel, the iommu_table pointer written to a device at [1] is
stale and needs an update.
This adds an "add_to_group" parameter to pnv_ioda_setup_bus_dma()
(in fact re-adds as it used to be there a while ago for different
reasons) to tell the helper if a device needs to be added to
an IOMMU group with an iommu_table update or just the latter.
This calls pnv_ioda_setup_bus_dma(..., false) from
pnv_ioda2_release_ownership() so when the ownership is restored,
32bit DMA can work again for a device. This does the same thing
on obtaining ownership as the iommu_table point is stale at this point
anyway and it is safer to have NULL there.
We did not hit this earlier as all tested devices in recent years were
only using 64bit DMA; the rare exception for this is MPT3 SAS adapter
which uses both 32bit and 64bit DMA access and it has not been tested
with VFIO much.
Signed-off-by: Alexey Kardashevskiy <[email protected]>
Acked-by: Gavin Shan <[email protected]>
Reviewed-by: David Gibson <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
Having only 32 memslots is a real constraint for the maximum
number of PCI devices that can be assigned to a single guest.
Assuming each PCI device/virtual function having two memory BAR
regions, we could assign only 15 devices/virtual functions to a
guest.
Hence increase KVM_USER_MEM_SLOTS to 512 as done in other archs like
powerpc.
Reviewed-by: Christoffer Dall <[email protected]>
Signed-off-by: Linu Cherian <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
|
|
arm/arm64 architecture doesnt use private memslots, hence removing
KVM_PRIVATE_MEM_SLOTS macro definition.
Reviewed-by: Christoffer Dall <[email protected]>
Signed-off-by: Linu Cherian <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
|
|
Return KVM_USER_MEM_SLOTS for userspace capability query on
NR_MEMSLOTS.
Reviewed-by: Christoffer Dall <[email protected]>
Signed-off-by: Linu Cherian <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
|
|
Add documentation for KVM_CAP_NR_MEMSLOTS capability.
Reviewed-by: Christoffer Dall <[email protected]>
Signed-off-by: Linu Cherian <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.11-rc2
dwc3 got a few fixes this time around:
Fixed an old bug where a broken endpoint descriptor passed in via
userspace through f_fs could prevent dwc3 from working because when
calculating max bursts, we could overwrite top 16 bits of a register.
Also fixed a bug on dwc3's ep_dequeue implementation which wasn't
properly incrementing our TRB dequeue pointer.
dwc3 on omap got two fixes: one for system suspend/resume and another
added a missing break statement on dwc3_omap_set_mailbox().
Apart from these, we have a set of smaller fixes including memory leak
in configfs, build warning fix in atmel udc and a revert of a broken
patch that went in during the merge window
|
|
The IODA2 specification says that a 64 DMA address cannot use top 4 bits
(3 are reserved and one is a "TVE select"); bottom page_shift bits
cannot be used for multilevel table addressing either.
The existing IODA2 table allocation code aligns the minimum TCE table
size to PAGE_SIZE so in the case of 64K system pages and 4K IOMMU pages,
we have 64-4-12=48 bits. Since 64K page stores 8192 TCEs, i.e. needs
13 bits, the maximum number of levels is 48/13 = 3 so we physically
cannot address more and EEH happens on DMA accesses.
This adds a check that too many levels were requested.
It is still possible to have 5 levels in the case of 4K system page size.
Signed-off-by: Alexey Kardashevskiy <[email protected]>
Acked-by: Gavin Shan <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
This warnings may be hit even in case they should not - in case user
puts a TC-flower rule which failed to be offloaded. So just remove them.
Reported-by: Petr Machata <[email protected]>
Reported-by: Ido Schimmel <[email protected]>
Fixes: commit 7aa0f5aa9030 ("mlxsw: spectrum: Implement TC flower offload")
Signed-off-by: Jiri Pirko <[email protected]>
Acked-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
KASAN detected a use-after-free:
[ 269.467067] BUG: KASAN: use-after-free in vrf_xmit+0x7f1/0x827 [vrf] at addr ffff8800350a21c0
[ 269.467067] Read of size 4 by task ssh/1879
[ 269.467067] CPU: 1 PID: 1879 Comm: ssh Not tainted 4.10.0+ #249
[ 269.467067] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 269.467067] Call Trace:
[ 269.467067] dump_stack+0x81/0xb6
[ 269.467067] kasan_object_err+0x21/0x78
[ 269.467067] kasan_report+0x2f7/0x450
[ 269.467067] ? vrf_xmit+0x7f1/0x827 [vrf]
[ 269.467067] ? ip_output+0xa4/0xdb
[ 269.467067] __asan_load4+0x6b/0x6d
[ 269.467067] vrf_xmit+0x7f1/0x827 [vrf]
...
Which corresponds to the skb access after xmit handling. Fix by saving
skb->len and using the saved value to update stats.
Fixes: 193125dbd8eb2 ("net: Introduce VRF device driver")
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This restores the ability to set a team device's mtu to anything higher
than 1500. Similar to the reported issue with bonding, the team driver
calls ether_setup(), which sets an initial max_mtu of 1500, while the
underlying hardware can handle something much larger. Just set it to
ETH_MAX_MTU to support all possible values, and the limitations of the
underlying devices will prevent setting anything too large.
Fixes: 91572088e3fd ("net: use core MTU range checking in core net infra")
CC: Cong Wang <[email protected]>
CC: Jiri Pirko <[email protected]>
CC: [email protected]
Signed-off-by: Jarod Wilson <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Those were supposed to go into the net-next tree not
the net tree. Oops...
Signed-off-by: David S. Miller <[email protected]>
|
|
Julian Margetson reported a panic on his SAM460EX with Kernel 4.11-rc1:
| Unable to handle kernel paging request for data at address 0x00000014
| Oops: Kernel access of bad area, sig: 11 [#1]
| PREEMPT
| Canyonlands
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper Not tainted [...]
| task: ea838000 task.stack: ea836000
| NIP: c0599f5c LR: c0599dd8 CTR: 00000000
| REGS: ea837c80 TRAP: 0300 Not tainted [...]
| MSR: 00029000 <CE,EE,ME>
| CR: 24371242 XER: 20000000
| DEAR: 00000014 ESR: 00000000
| GPR00: c0599ce8 ea837d30 ea838000 c0e52dcc c0d56ffb [...]
| NIP [c0599f5c] emac_probe+0xfb4/0x1304
| LR [c0599dd8] emac_probe+0xe30/0x1304
| Call Trace:
| [ea837d30] [c0599ce8] emac_probe+0xd40/0x1304 (unreliable)
| [ea837d80] [c0533504] platform_drv_probe+0x48/0x90
| [ea837da0] [c0531c14] driver_probe_device+0x15c/0x2c4
| [ea837dd0] [c0531e04] __driver_attach+0x88/0xb0
| ---[ end trace ... ]---
The problem is caused by emac_dt_phy_probe() returing success (0)
for existing device-trees configurations that do not specify a
"phy-handle" property. This caused the code to skip the existing
phy probe and setup. Which led to essential phy related
data-structures being uninitialized.
This patch also removes the unused variable in emac_dt_phy_connect().
Fixes: a577ca6badb5261d ("net: emac: add support for device-tree based PHY discovery and setup")
Reported-by: Julian Margetson <[email protected]>
Signed-off-by: Christian Lamparter <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <[email protected]>
Tested-by: Geoff Levand <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <[email protected]>
Tested-by: Robert Jarzmik <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
On POWER8 (ISA 2.07) lxvx and stxvx are defined to be extended mnemonics
of lxvd2x and stxvd2x. For POWER9 (ISA 3.0) the HW architects in their
infinite wisdom made lxvx and stxvx instructions in their own right.
POWER9 aware GCC will use the POWER9 instruction for lxvx and stxvx
causing these selftests to fail on POWER8. Further compounding the
issue, because of the way -mvsx works it will cause the power9
instructions to be used regardless of -mcpu=power8 to GCC or -mpower8 to
AS.
The safest way to address the problem for now is to not use the extended
mnemonic. We don't care how the CPU loads the values from memory since
the tests only performs register comparisons, so using stdvd2x/lxvd2x
does not impact the test.
Signed-off-by: Cyril Bur <[email protected]>
Acked-by: Balbir Singh<[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
MMCRA[SDAR_MODE] specifices how the SDAR should be updated in
continous sampling mode. On P9 it must be set to 0b00 when
MMCRA[63] is set.
Fixes: c7c3f568beff2 ('powerpc/perf: macros for power9 format encoding')
Signed-off-by: Madhavan Srinivasan <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
Power9 DD1 do not support PMU_HAS_SIER flag and sdsync in
perf_get_data_addr() defaults to MMCRA_SDSYNC which is wrong. Since
power9 MMCRA does not support SDSYNC bit, patch includes PPMU_NO_SIAR
flag to the check and set the sdsync with MMCRA_SAMPLE_ENABLE;
Fixes: 27593d72c4ad ("powerpc/perf: Use MSR to report privilege level on P9 DD1")
Signed-off-by: Madhavan Srinivasan <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched.h split-up fixes for MIPS from Ingo Molnar:
"These are the fixes for MIPS build failures due to the sched.h
split-up, from Arnd Bergmann"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MIPS: Add missing include files
|
|
Signed-off-by: Jim Qu <[email protected]>
Reviewed-by: Alex Deucher <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Commit 13ad59df67f1 ("mm, page_alloc: avoid page_to_pfn() when merging
buddies") moved the check for memory holes out of page_is_buddy() and
had the callers do the check.
But this wasn't done correctly in one place which caused ia64 to crash
very early in boot.
Update to fix that and make ia64 boot again.
[ v2: Vlastimil pointed out we don't need to call page_to_pfn()
since we already have the result of that in "buddy_pfn" ]
Fixes: 13ad59df67f1 ("avoid page_to_pfn() when merging buddies")
Cc: Mel Gorman <[email protected]>
Cc: Joonsoo Kim <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: "Kirill A. Shutemov" <[email protected]>
Cc: Johannes Weiner <[email protected]>
Cc: Andrew Morton <[email protected]>
Signed-off-by: Tony Luck <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest fixes from Steven Rostedt:
"Greg Kroah-Hartman reported to me that the ktest of v4.11-rc1 locked
up in an infinite loop while doing the make mrproper.
Looking into the cause I noticed that a recent update to the function
run_command (used for running all shell commands, including "make
mrproper") changed the internal loop to use the function
wait_for_input.
The wait_for_input function uses select to look at two file
descriptors. One is the file descriptor of the command it is running,
the other is STDIN. The STDIN check was not checking the return status
of the sysread call, and was also just writing a lot of data into
syswrite without regard to the size of the data read.
Changing the code to check the return status of sysread, and also to
still process the passed in descriptor data without looping back to
the select fixed Greg's problem.
While looking at this code I also realized that the loop did not honor
the timeout if STDIN always had input (or for some reason return
error). this could prevent wait_for_input to timeout on the file
descriptor it is suppose to be waiting for. That is fixed too"
* tag 'ktest-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Make sure wait_for_input does honor the timeout
ktest: Fix while loop in wait_for_input
|
|
This removes the extra include header file that was added in commit
e58bc927835a "Pull overlayfs updates from Miklos Szeredi" now that it
is no longer needed.
There are probably other such includes that got added during the
scheduler header splitup series, but this is the one that annoyed me
personally and I know about.
Signed-off-by: Linus Torvalds <[email protected]>
|
|
When a reflink operation causes the bmap code to allocate a btree block
we're currently doing single-AG allocations due to having ->firstblock
set and then try any higher AG due a little reflink quirk we've put in
when adding the reflink code. But given that we do not have a minleft
reservation of any kind in this AG we can still not have any space in
the same or higher AG even if the file system has enough free space.
To fix this use a XFS_ALLOCTYPE_FIRST_AG allocation in this fall back
path instead.
[And yes, we need to redo this properly instead of piling hacks over
hacks. I'm working on that, but it's not going to be a small series.
In the meantime this fixes the customer reported issue]
Also add a warning for failing allocations to make it easier to debug.
Signed-off-by: Christoph Hellwig <[email protected]>
Reviewed-by: Darrick J. Wong <[email protected]>
Signed-off-by: Darrick J. Wong <[email protected]>
|
|
The scheduler header file split and cleanups ended up exposing a few
nasty header file dependencies, and in particular it showed how we in
<linux/wait.h> ended up depending on "signal_pending()", which now comes
from <linux/sched/signal.h>.
That's a very subtle and annoying dependency, which already caused a
semantic merge conflict (see commit e58bc927835a "Pull overlayfs updates
from Miklos Szeredi", which added that fixup in the merge commit).
It turns out that we can avoid this dependency _and_ improve code
generation by moving the guts of the fairly nasty helper #define
__wait_event_interruptible_locked() to out-of-line code. The code that
includes the signal_pending() check is all in the slow-path where we
actually go to sleep waiting for the event anyway, so using a helper
function is the right thing to do.
Using a helper function is also what we already did for the non-locked
versions, see the "__wait_event*()" macros and the "prepare_to_wait*()"
set of helper functions.
We might want to try to unify all these macro games, we have a _lot_ of
subtly different wait-event loops. But this is the minimal patch to fix
the annoying header dependency.
Acked-by: Ingo Molnar <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Commit fa7f138 ("xfs: clear delalloc and cache on buffered write
failure") fixed one regression in the iomap error handling code and
exposed another. The fundamental problem is that if a buffered write
is a rewrite of preexisting delalloc blocks and the write fails, the
failure handling code can punch out preexisting blocks with valid
file data.
This was reproduced directly by sub-block writes in the LTP
kernel/syscalls/write/write03 test. A first 100 byte write allocates
a single block in a file. A subsequent 100 byte write fails and
punches out the block, including the data successfully written by
the previous write.
To address this problem, update the ->iomap_begin() handler to
distinguish newly allocated delalloc blocks from preexisting
delalloc blocks via the IOMAP_F_NEW flag. Use this flag in the
->iomap_end() handler to decide when a failed or short write should
punch out delalloc blocks.
This introduces the subtle requirement that ->iomap_begin() should
never combine newly allocated delalloc blocks with existing blocks
in the resulting iomap descriptor. This can occur when a new
delalloc reservation merges with a neighboring extent that is part
of the current write, for example. Therefore, drop the
post-allocation extent lookup from xfs_bmapi_reserve_delalloc() and
just return the record inserted into the fork. This ensures only new
blocks are returned and thus that preexisting delalloc blocks are
always handled as "found" blocks and not punched out on a failed
rewrite.
Reported-by: Xiong Zhou <[email protected]>
Signed-off-by: Brian Foster <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Darrick J. Wong <[email protected]>
Signed-off-by: Darrick J. Wong <[email protected]>
|
|
It is invalid to call del_gendisk() when disk->queue is NULL. Fix error
handling in axon_ram_probe() to avoid doing that.
Also del_gendisk() does not drop a reference to gendisk allocated by
alloc_disk(). That has to be done by put_disk(). Add that call where
needed.
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Jan Kara <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
To avoid recursion on the kernel stack when stacked block devices
are in use, generic_make_request() will, when called recursively,
queue new requests for later handling. They will be handled when the
make_request_fn for the current bio completes.
If any bios are submitted by a make_request_fn, these will ultimately
be handled seqeuntially. If the handling of one of those generates
further requests, they will be added to the end of the queue.
This strict first-in-first-out behaviour can lead to deadlocks in
various ways, normally because a request might need to wait for a
previous request to the same device to complete. This can happen when
they share a mempool, and can happen due to interdependencies
particular to the device. Both md and dm have examples where this happens.
These deadlocks can be erradicated by more selective ordering of bios.
Specifically by handling them in depth-first order. That is: when the
handling of one bio generates one or more further bios, they are
handled immediately after the parent, before any siblings of the
parent. That way, when generic_make_request() calls make_request_fn
for some particular device, we can be certain that all previously
submited requests for that device have been completely handled and are
not waiting for anything in the queue of requests maintained in
generic_make_request().
An easy way to achieve this would be to use a last-in-first-out stack
instead of a queue. However this will change the order of consecutive
bios submitted by a make_request_fn, which could have unexpected consequences.
Instead we take a slightly more complex approach.
A fresh queue is created for each call to a make_request_fn. After it completes,
any bios for a different device are placed on the front of the main queue, followed
by any bios for the same device, followed by all bios that were already on
the queue before the make_request_fn was called.
This provides the depth-first approach without reordering bios on the same level.
This, by itself, it not enough to remove all deadlocks. It just makes
it possible for drivers to take the extra step required themselves.
To avoid deadlocks, drivers must never risk waiting for a request
after submitting one to generic_make_request. This includes never
allocing from a mempool twice in the one call to a make_request_fn.
A common pattern in drivers is to call bio_split() in a loop, handling
the first part and then looping around to possibly split the next part.
Instead, a driver that finds it needs to split a bio should queue
(with generic_make_request) the second part, handle the first part,
and then return. The new code in generic_make_request will ensure the
requests to underlying bios are processed first, then the second bio
that was split off. If it splits again, the same process happens. In
each case one bio will be completely handled before the next one is attempted.
With this is place, it should be possible to disable the
punt_bios_to_recover() recovery thread for many block devices, and
eventually it may be possible to remove it completely.
Ref: http://www.spinics.net/lists/raid/msg54680.html
Tested-by: Jinpu Wang <[email protected]>
Inspired-by: Lars Ellenberg <[email protected]>
Signed-off-by: NeilBrown <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
This reverts commit 0dba1314d4f81115dce711292ec7981d17231064. It causes
leaking of device numbers for SCSI when SCSI registers multiple gendisks
for one request_queue in succession. It can be easily reproduced using
Omar's script [1] on kernel with CONFIG_DEBUG_TEST_DRIVER_REMOVE.
Furthermore the protection provided by this commit is not needed anymore
as the problem it was fixing got also fixed by commit 165a5e22fafb
"block: Move bdi_unregister() to del_gendisk()".
[1]: http://marc.info/?l=linux-block&m=148554717109098&w=2
Signed-off-by: Jan Kara <[email protected]>
Acked-by: Dan Williams <[email protected]>
Tested-by: Omar Sandoval <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Commit 165a5e22fafb "block: Move bdi_unregister() to del_gendisk()"
added disk->queue dereference to del_gendisk(). Although del_gendisk()
is not supposed to be called without disk->queue valid and
blk_unregister_queue() warns in that case, this change will make it oops
instead. Return to the old more robust behavior of just warning when
del_gendisk() gets called for gendisk with disk->queue being NULL.
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Jan Kara <[email protected]>
Tested-by: Omar Sandoval <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
bdi_writeback_congested structures get created for each blkcg and bdi
regardless whether bdi is registered or not. When they are created in
unregistered bdi and the request queue (and thus bdi) is then destroyed
while blkg still holds reference to bdi_writeback_congested structure,
this structure will be referencing freed bdi and last wb_congested_put()
will try to remove the structure from already freed bdi.
With commit 165a5e22fafb "block: Move bdi_unregister() to
del_gendisk()", SCSI started to destroy bdis without calling
bdi_unregister() first (previously it was calling bdi_unregister() even
for unregistered bdis) and thus the code detaching
bdi_writeback_congested in cgwb_bdi_destroy() was not triggered and we
started hitting this use-after-free bug. It is enough to boot a KVM
instance with virtio-scsi device to trigger this behavior.
Fix the problem by detaching bdi_writeback_congested structures in
bdi_exit() instead of bdi_unregister(). This is also more logical as
they can get attached to bdi regardless whether it ever got registered
or not.
Fixes: 165a5e22fafb127ecb5914e12e8c32a1f0d3f820
Signed-off-by: Jan Kara <[email protected]>
Tested-by: Omar Sandoval <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
SCSI can call device_add_disk() several times for one request queue when
a device in unbound and bound, creating new gendisk each time. This will
lead to bdi being repeatedly registered and unregistered. This was not a
big problem until commit 165a5e22fafb "block: Move bdi_unregister() to
del_gendisk()" since bdi was only registered repeatedly (bdi_register()
handles repeated calls fine, only we ended up leaking reference to
gendisk due to overwriting bdi->owner) but unregistered only in
blk_cleanup_queue() which didn't get called repeatedly. After
165a5e22fafb we were doing correct bdi_register() - bdi_unregister()
cycles however bdi_unregister() is not prepared for it. So make sure
bdi_unregister() cleans up bdi in such a way that it is prepared for
a possible following bdi_register() call.
An easy way to provoke this behavior is to enable
CONFIG_DEBUG_TEST_DRIVER_REMOVE and use scsi_debug driver to create a
scsi disk which immediately hangs without this fix.
Fixes: 165a5e22fafb127ecb5914e12e8c32a1f0d3f820
Signed-off-by: Jan Kara <[email protected]>
Tested-by: Omar Sandoval <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Phil Sutter reports that IPv6 AH header matching is broken. From
userspace, nft generates bytecode that expects to find the AH header at
NFT_PAYLOAD_TRANSPORT_HEADER both for IPv4 and IPv6. However,
pktinfo->thoff is set to the inner header after the AH header in IPv6,
while in IPv4 pktinfo->thoff points to the AH header indeed. This
behaviour is inconsistent. This patch fixes this problem by updating
ipv6_find_hdr() to get the IP6_FH_F_AUTH flag so this function stops at
the AH header, so both IPv4 and IPv6 pktinfo->thoff point to the AH
header.
This is also inconsistent when trying to match encapsulated headers:
1) A packet that looks like IPv4 + AH + TCP dport 22 will *not* match.
2) A packet that looks like IPv6 + AH + TCP dport 22 will match.
Reported-by: Phil Sutter <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|