| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use the newly introduced usb_control_msg_send() instead of usb_control_msg()
when selecting the channel.
Reviewed-by: Alan Stern <[email protected]>
Signed-off-by: Helge Deller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.4-rc3 to resolve
some reported problems, and add some new device ids. These include:
- termios documentation updates
- vc_screen use-after-free fix
- memory leak fix in arc_uart driver
- new 8250 driver ids
- other small serial driver fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vc_screen: reload load of struct vc_data pointer in vcs_write() to avoid UAF
serial: qcom-geni: fix enabling deactivated interrupt
serial: 8250_bcm7271: fix leak in `brcmuart_probe`
serial: 8250_bcm7271: balance clk_enable calls
serial: arc_uart: fix of_iomap leak in `arc_serial_probe`
serial: 8250: Document termios parameter of serial8250_em485_config()
serial: Add support for Advantech PCI-1611U card
serial: 8250_exar: Add support for USR298x PCI Modems
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt fixes from Greg KH:
"Here are some USB fixes for 6.4-rc3, as well as a driver core fix that
resolves a memory leak that shows up in USB devices easier than other
subsystems.
Included in here are:
- driver core memory leak as reported and tested by syzbot and
developers
- dwc3 driver fixes for reported problems
- xhci driver fixes for reported problems
- USB gadget driver reverts to resolve regressions
- usbtmc driver fix for syzbot reported problem
- thunderbolt driver fixes for reported issues
- other small USB fixes
All of these, except for the driver core fix, have been in linux-next
with no reported problems. The driver core fix was tested and verified
to solve the issue by syzbot and the original reporter"
* tag 'usb-6.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
driver core: class: properly reference count class_dev_iter()
xhci: Fix incorrect tracking of free space on transfer rings
xhci-pci: Only run d3cold avoidance quirk for s2idle
usb-storage: fix deadlock when a scsi command timeouts more than once
usb: dwc3: fix a test for error in dwc3_core_init()
usb: typec: tps6598x: Fix fault at module removal
usb: gadget: u_ether: Fix host MAC address case
usb: typec: altmodes/displayport: fix pin_assignment_show
Revert "usb: gadget: udc: core: Invoke usb_gadget_connect only when started"
Revert "usb: gadget: udc: core: Prevent redundant calls to pullup"
usb: gadget: drop superfluous ':' in doc string
usb: dwc3: debugfs: Resume dwc3 before accessing registers
USB: UHCI: adjust zhaoxin UHCI controllers OverCurrent bit value
usb: dwc3: fix gadget mode suspend interrupt handler issue
usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()
USB: usbtmc: Fix direction for 0-length ioctl control messages
thunderbolt: Clear registers properly when auto clear isn't in use
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- More device quirks (Sagi, Hristo, Adrian, Daniel)
- Controller delete race (Maurizo)
- Multipath cleanup fix (Christoph)
- Deny writeable mmap mapping on a readonly block device (Loic)
- Kill unused define that got introduced by accident (Christoph)
- Error handling fix for s390 dasd (Stefan)
- ublk locking fix (Ming)
* tag 'block-6.4-2023-05-20' of git://git.kernel.dk/linux:
block: remove NFL4_UFLG_MASK
block: Deny writable memory mapping if block is read-only
s390/dasd: fix command reject error on ESE devices
nvme-pci: Add quirk for Teamgroup MP33 SSD
ublk: fix AB-BA lockdep warning
nvme: do not let the user delete a ctrl before a complete initialization
nvme-multipath: don't call blk_mark_disk_dead in nvme_mpath_remove_disk
nvme-pci: clamp max_hw_sectors based on DMA optimized limitation
nvme-pci: add quirk for missing secondary temperature thresholds
nvme-pci: add NVME_QUIRK_BOGUS_NID for HS-SSD-FUTURE 2048G
|
|
The NFL4_UFLG_MASK define slipped in in commit 9208d4149758
("block: add a ->get_unique_id method") and should never have been
added, as NFSD as the only user of it already has it's copy.
Signed-off-by: Christoph Hellwig <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fix compiler warnings on btnxpuart
- Fix potential double free on hci_conn_unlink
- Fix UAF on hci_conn_hash_flush
* tag 'for-net-2023-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: btnxpuart: Fix compiler warnings
Bluetooth: Unlink CISes when LE disconnects in hci_conn_del
Bluetooth: Fix UAF in hci_conn_hash_flush again
Bluetooth: Refcnt drop must be placed last in hci_conn_unlink
Bluetooth: Fix potential double free caused by hci_conn_unlink
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.
team0
|
+------+------+-----+-----+
| | | | |
team1 team2 team3 ... team200
If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.
But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.
Reproducer:
ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
ip link add team$i master team0 type team
ethtool -K team$i lro on
done
ethtool -K team0 lro off
In order to fix it, the notifier_ctx member of bonding/team is introduced.
Reported-by: [email protected]
Fixes: fd867d51f889 ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Taehee Yoo <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Reviewed-by: Nikolay Aleksandrov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Aditi Ghag says:
====================
This patch set adds the capability to destroy sockets in BPF. We plan to
use the capability in Cilium to force client sockets to reconnect when
their remote load-balancing backends are deleted. The other use case is
on-the-fly policy enforcement where existing socket connections
prevented by policies need to be terminated.
The use cases, and more details around
the selected approach were presented at LPC 2022 -
https://lpc.events/event/16/contributions/1358/.
RFC discussion -
https://lore.kernel.org/netdev/CABG=zsBEh-P4NXk23eBJw7eajB5YJeRS7oPXnTAzs=yob4EMoQ@mail.gmail.com/T/#u.
v8 patch series -
https://lore.kernel.org/bpf/[email protected]/
v9 highlights:
Address review comments:
Martin:
- Rearranged the kfunc filter patch, and added the missing break
statement.
- Squashed the extended selftest/bpf patch.
Yonghong:
- Revised commit message for patch 1.
(Below notes are same as v8 patch series that are still relevant. Refer to
earlier patch series versions for other notes.)
- I hit a snag while writing the kfunc where verifier complained about the
`sock_common` type passed from TCP iterator. With kfuncs, there don't
seem to be any options available to pass BTF type hints to the verifier
(equivalent of `ARG_PTR_TO_BTF_ID_SOCK_COMMON`, as was the case with the
helper). As a result, I changed the argument type of the sock_destory
kfunc to `sock_common`.
====================
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
The test cases for destroying sockets mirror the intended usages of the
bpf_sock_destroy kfunc using iterators.
The destroy helpers set `ECONNABORTED` error code that we can validate
in the test code with client sockets. But UDP sockets have an overriding
error code from `disconnect()` called during abort, so the error code
validation is only done for TCP sockets.
The failure test cases validate that the `bpf_sock_destroy` kfunc is not
allowed from program attach types other than BPF trace iterator, and
such programs fail to load.
Signed-off-by: Aditi Ghag <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
The helper will be used to programmatically retrieve
and pass ports in userspace and kernel selftest programs.
Suggested-by: Stanislav Fomichev <[email protected]>
Signed-off-by: Aditi Ghag <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
The socket destroy kfunc is used to forcefully terminate sockets from
certain BPF contexts. We plan to use the capability in Cilium
load-balancing to terminate client sockets that continue to connect to
deleted backends. The other use case is on-the-fly policy enforcement
where existing socket connections prevented by policies need to be
forcefully terminated. The kfunc also allows terminating sockets that may
or may not be actively sending traffic.
The kfunc can currently be called only from BPF TCP and UDP iterators
where users can filter, and terminate selected sockets. More
specifically, it can only be called from BPF contexts that ensure
socket locking in order to allow synchronous execution of protocol
specific `diag_destroy` handlers. The previous commit that batches UDP
sockets during iteration facilitated a synchronous invocation of the UDP
destroy callback from BPF context by skipping socket locks in
`udp_abort`. TCP iterator already supported batching of sockets being
iterated. To that end, `tracing_iter_filter` callback filter is added so
that verifier can restrict the kfunc to programs with `BPF_TRACE_ITER`
attach type, and reject other programs.
The kfunc takes `sock_common` type argument, even though it expects, and
casts them to a `sock` pointer. This enables the verifier to allow the
sock_destroy kfunc to be called for TCP with `sock_common` and UDP with
`sock` structs. Furthermore, as `sock_common` only has a subset of
certain fields of `sock`, casting pointer to the latter type might not
always be safe for certain sockets like request sockets, but these have a
special handling in the diag_destroy handlers.
Additionally, the kfunc is defined with `KF_TRUSTED_ARGS` flag to avoid the
cases where a `PTR_TO_BTF_ID` sk is obtained by following another pointer.
eg. getting a sk pointer (may be even NULL) by following another sk
pointer. The pointer socket argument passed in TCP and UDP iterators is
tagged as `PTR_TRUSTED` in {tcp,udp}_reg_info. The TRUSTED arg changes
are contributed by Martin KaFai Lau <[email protected]>.
Signed-off-by: Aditi Ghag <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
This commit adds the ability to filter kfuncs to certain BPF program
types. This is required to limit bpf_sock_destroy kfunc implemented in
follow-up commits to programs with attach type 'BPF_TRACE_ITER'.
The commit adds a callback filter to 'struct btf_kfunc_id_set'. The
filter has access to the `bpf_prog` construct including its properties
such as `expected_attached_type`.
Signed-off-by: Aditi Ghag <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
The syzbot fuzzer detected a problem in the udlfb driver, caused by an
endpoint not having the expected type:
usb 1-1: Read EDID byte 0 failed: -71
usb 1-1: Unable to get valid EDID from device/display
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 9 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880
drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 9 Comm: kworker/0:1 Not tainted
6.4.0-rc1-syzkaller-00016-ga4422ff22142 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
04/28/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
dlfb_submit_urb+0x92/0x180 drivers/video/fbdev/udlfb.c:1980
dlfb_set_video_mode+0x21f0/0x2950 drivers/video/fbdev/udlfb.c:315
dlfb_ops_set_par+0x2a7/0x8d0 drivers/video/fbdev/udlfb.c:1111
dlfb_usb_probe+0x149a/0x2710 drivers/video/fbdev/udlfb.c:1743
The current approach for this issue failed to catch the problem
because it only checks for the existence of a bulk-OUT endpoint; it
doesn't check whether this endpoint is the one that the driver will
actually use.
We can fix the problem by instead checking that the endpoint used by
the driver does exist and is bulk-OUT.
Reported-and-tested-by: [email protected]
Signed-off-by: Alan Stern <[email protected]>
CC: Pavel Skripkin <[email protected]>
Fixes: aaf7dbe07385 ("video: fbdev: udlfb: properly check endpoint type")
Signed-off-by: Helge Deller <[email protected]>
|
|
Just below the removed lines par->clk_wr_offset is hard coded to 3 so
there is no use in determining a different clock just to then ignore it
anyway. This also removes the only I/O port use remaining in the driver
allowing it to be built without CONFIG_HAS_IOPORT.
Link: https://lore.kernel.org/all/[email protected]/
Suggested-by: Ville Syrjälä <[email protected]>
Signed-off-by: Niklas Schnelle <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Signed-off-by: Helge Deller <[email protected]>
|
|
Building with W=1 shows that a header needs to be included to
make the prototypes visible:
drivers/video/fbdev/i810/i810_dvt.c:194:6: error: no previous prototype for 'round_off_xres' [-Werror=missing-prototypes]
drivers/video/fbdev/i810/i810_dvt.c:233:6: error: no previous prototype for 'i810fb_encode_registers' [-Werror=missing-prototypes]
drivers/video/fbdev/i810/i810_dvt.c:245:6: error: no previous prototype for 'i810fb_fill_var_timings' [-Werror=missing-prototypes]
drivers/video/fbdev/i810/i810_dvt.c:279:5: error: no previous prototype for 'i810_get_watermark' [-Werror=missing-prototypes]
Adding the header leads to another warning from a mismatched
prototype, so fix this as well:
drivers/video/fbdev/i810/i810_dvt.c:280:5: error: conflicting types for 'i810_get_watermark'; have 'u32(struct fb_var_screeninfo *,
Signed-off-by: Arnd Bergmann <[email protected]>
Reviewed-by: Jani Nikula <[email protected]>
Signed-off-by: Helge Deller <[email protected]>
|
|
There is a global function with this name on sparc, but no
global declaration:
drivers/video/fbdev/core/fbmem.c:1469:15: error: no previous prototype for 'get_fb_unmapped_area'
Make the generic definition static to avoid this warning. On
sparc, this is never seen.
Edit by Helge:
Update Kconfig text as suggested by Geert Uytterhoeven.
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Helge Deller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-05-18 (igc, igb, e1000e)
This series contains updates to igc, igb, and e1000e drivers.
Kurt Kanzenbach adds calls to txq_trans_cond_update() for XDP transmit
on igc.
Tom Rix makes definition of igb_pm_ops conditional on CONFIG_PM for igb.
Baozhu Ni adds a missing kdoc description on e1000e.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000e: Add @adapter description to kdoc
igb: Define igb_pm_ops conditionally on CONFIG_PM
igc: Avoid transmit queue timeout for XDP
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
User should not be able to write block device if it is read-only at
block level (e.g force_ro attribute). This is ensured in the regular
fops write operation (blkdev_write_iter) but not when writing via
user mapping (mmap), allowing user to actually write a read-only
block device via a PROT_WRITE mapping.
Example: This can lead to integrity issue of eMMC boot partition
(e.g mmcblk0boot0) which is read-only by default.
To fix this issue, simply deny shared writable mapping if the block
is readonly.
Note: Block remains writable if switch to read-only is performed
after the initial mapping, but this is expected behavior according
to commit a32e236eb93e ("Partially revert "block: fail op_is_write()
requests to read-only partitions"")'.
Signed-off-by: Loic Poulain <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
Pull drm fixes from Dave Airlie:
"Regular fixes pull, amdgpu and msm make up most of these, nothing too
serious, also one i915 and one exynos.
I didn't get a misc fixes pull this week (one of the maintainers is
off, so have to engage the backup) so I think there are a few
outstanding patches that will show up next week,
amdgpu:
- update gfx11 clock counter logic
- Fix a race when disabling gfxoff on gfx10/11 for profiling
- Raven/Raven2/PCO clock counter fix
- Add missing get_vbios_fb_size for GMC 11
- Fix a spurious irq warning in the device remove case
- Fix possible power mode mismatch between driver and PMFW
- USB4 fix
exynos:
- fix build warning
i915:
- fix missing NULL check in HDCP code
msm:
- display:
- msm8998: fix fetch and qos to align with downstream
- msm8998: fix LM pairs to align with downstream
- remove unused INTF0 interrupt mask on some chipsets
- remove TE2 block from relevant chipsets
- relocate non-MDP_TOP offset to different header
- fix some indentation
- fix register offets/masks for dither blocks
- make ping-ping block length 0
- remove duplicated defines
- fix log mask for writeback block
- unregister the hdmi codec for dp during unbind
- fix yaml warnings
- gpu:
- fix submit error path leak
- arm-smmu-qcom fix for regression that broke per-process page
tables
- fix no-iommu crash"
* tag 'drm-fixes-2023-05-20' of git://anongit.freedesktop.org/drm/drm: (29 commits)
drm/amd/display: enable dpia validate
drm/amd/pm: fix possible power mode mismatch between driver and PMFW
drm/amdgpu: skip disabling fence driver src_irqs when device is unplugged
drm/amdgpu/gmc11: implement get_vbios_fb_size()
drm/amdgpu: Differentiate between Raven2 and Raven/Picasso according to revision id
drm/amdgpu/gfx11: Adjust gfxoff before powergating on gfx11 as well
drm/amdgpu/gfx10: Disable gfxoff before disabling powergating.
drm/amdgpu/gfx11: update gpu_clock_counter logic
drm/msm: Be more shouty if per-process pgtables aren't working
iommu/arm-smmu-qcom: Fix missing adreno_smmu's
drm/i915/hdcp: Check if media_gt exists
drm/exynos: fix g2d_open/close helper function definitions
drm/msm: Fix submit error-path leaks
drm/msm/iommu: Fix null pointer dereference in no-IOMMU case
dt-bindings: display/msm: dsi-controller-main: Document qcom, master-dsi and qcom, sync-dual-dsi
drm/msm/dpu: Remove duplicate register defines from INTF
drm/msm/dpu: Set PINGPONG block length to zero for DPU >= 7.0.0
drm/msm/dpu: Use V2 DITHER PINGPONG sub-block in SM8[34]50/SC8280XP
drm/msm/dpu: Fix PP_BLK_DIPHER -> DITHER typo
drm/msm/dpu: Reindent REV_7xxx interrupt masks with tabs
...
|
|
Formatting a thin-provisioned (ESE) device that is part of a PPRC copy
relation might fail with the following error:
dasd-eckd 0.0.f500: An error occurred in the DASD device driver, reason=09
[...]
24 Byte: 0 MSG 4, no MSGb to SYSOP
During format of an ESE disk the Release Allocated Space command is used.
A bit in the payload of the command is set that is not allowed to be set
for devices in a copy relation. This bit is set to allow the partial
release of an extent.
Check for the existence of a copy relation before setting the respective
bit.
Fixes: 91dc4a197569 ("s390/dasd: Add new ioctl to release space")
Cc: [email protected] # 5.3+
Signed-off-by: Stefan Haberland <[email protected]>
Reviewed-by: Jan Hoeppner <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
Batch UDP sockets from BPF iterator that allows for overlapping locking
semantics in BPF/kernel helpers executed in BPF programs. This facilitates
BPF socket destroy kfunc (introduced by follow-up patches) to execute from
BPF iterator programs.
Previously, BPF iterators acquired the sock lock and sockets hash table
bucket lock while executing BPF programs. This prevented BPF helpers that
again acquire these locks to be executed from BPF iterators. With the
batching approach, we acquire a bucket lock, batch all the bucket sockets,
and then release the bucket lock. This enables BPF or kernel helpers to
skip sock locking when invoked in the supported BPF contexts.
The batching logic is similar to the logic implemented in TCP iterator:
https://lore.kernel.org/bpf/[email protected]/.
Suggested-by: Martin KaFai Lau <[email protected]>
Signed-off-by: Aditi Ghag <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
This is a preparatory commit to remove the field. The field was
previously shared between proc fs and BPF UDP socket iterators. As the
follow-up commits will decouple the implementation for the iterators,
remove the field. As for BPF socket iterator, filtering of sockets is
exepected to be done in BPF programs.
Suggested-by: Martin KaFai Lau <[email protected]>
Signed-off-by: Aditi Ghag <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
This is a preparatory commit that encapsulates the logic
to get udp table in iterator inside udp_get_table_afinfo, and
renames the function to `udp_get_table_seq` accordingly.
Suggested-by: Martin KaFai Lau <[email protected]>
Signed-off-by: Aditi Ghag <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
This is a preparatory commit to refactor code that matches socket
attributes in iterators to a helper function, and use it in the
proc fs iterator.
Signed-off-by: Aditi Ghag <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
This is a preparatory commit to replace `lock_sock_fast` with
`lock_sock`,and facilitate BPF programs executed from the TCP sockets
iterator to be able to destroy TCP sockets using the bpf_sock_destroy
kfunc (implemented in follow-up commits).
Previously, BPF TCP iterator was acquiring the sock lock with BH
disabled. This led to scenarios where the sockets hash table bucket lock
can be acquired with BH enabled in some path versus disabled in other.
In such situation, kernel issued a warning since it thinks that in the
BH enabled path the same bucket lock *might* be acquired again in the
softirq context (BH disabled), which will lead to a potential dead lock.
Since bpf_sock_destroy also happens in a process context, the potential
deadlock warning is likely a false alarm.
Here is a snippet of annotated stack trace that motivated this change:
```
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&h->lhash2[i].lock);
local_bh_disable();
lock(&h->lhash2[i].lock);
kernel imagined possible scenario:
local_bh_disable(); /* Possible softirq */
lock(&h->lhash2[i].lock);
*** Potential Deadlock ***
process context:
lock_acquire+0xcd/0x330
_raw_spin_lock+0x33/0x40
------> Acquire (bucket) lhash2.lock with BH enabled
__inet_hash+0x4b/0x210
inet_csk_listen_start+0xe6/0x100
inet_listen+0x95/0x1d0
__sys_listen+0x69/0xb0
__x64_sys_listen+0x14/0x20
do_syscall_64+0x3c/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
bpf_sock_destroy run from iterator:
lock_acquire+0xcd/0x330
_raw_spin_lock+0x33/0x40
------> Acquire (bucket) lhash2.lock with BH disabled
inet_unhash+0x9a/0x110
tcp_set_state+0x6a/0x210
tcp_abort+0x10d/0x200
bpf_prog_6793c5ca50c43c0d_iter_tcp6_server+0xa4/0xa9
bpf_iter_run_prog+0x1ff/0x340
------> lock_sock_fast that acquires sock lock with BH disabled
bpf_iter_tcp_seq_show+0xca/0x190
bpf_seq_read+0x177/0x450
```
Also, Yonghong reported a deadlock for non-listening TCP sockets that
this change resolves. Previously, `lock_sock_fast` held the sock spin
lock with BH which was again being acquired in `tcp_abort`:
```
watchdog: BUG: soft lockup - CPU#0 stuck for 86s! [test_progs:2331]
RIP: 0010:queued_spin_lock_slowpath+0xd8/0x500
Call Trace:
<TASK>
_raw_spin_lock+0x84/0x90
tcp_abort+0x13c/0x1f0
bpf_prog_88539c5453a9dd47_iter_tcp6_client+0x82/0x89
bpf_iter_run_prog+0x1aa/0x2c0
? preempt_count_sub+0x1c/0xd0
? from_kuid_munged+0x1c8/0x210
bpf_iter_tcp_seq_show+0x14e/0x1b0
bpf_seq_read+0x36c/0x6a0
bpf_iter_tcp_seq_show
lock_sock_fast
__lock_sock_fast
spin_lock_bh(&sk->sk_lock.slock);
/* * Fast path return with bottom halves disabled and * sock::sk_lock.slock held.* */
...
tcp_abort
local_bh_disable();
spin_lock(&((sk)->sk_lock.slock)); // from bh_lock_sock(sk)
```
With the switch to `lock_sock`, it calls `spin_unlock_bh` before returning:
```
lock_sock
lock_sock_nested
spin_lock_bh(&sk->sk_lock.slock);
:
spin_unlock_bh(&sk->sk_lock.slock);
```
Acked-by: Yonghong Song <[email protected]>
Acked-by: Stanislav Fomichev <[email protected]>
Signed-off-by: Aditi Ghag <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six small fixes.
Four in drivers and the two core changes should be read together as a
correction to a prior iorequest_cnt fix that exposed us to a potential
use after free"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Decrease scsi_device's iorequest_cnt if dispatch failed
scsi: Revert "scsi: core: Do not increase scsi_device's iorequest_cnt if dispatch failed"
scsi: storvsc: Don't pass unused PFNs to Hyper-V host
scsi: ufs: core: Fix MCQ nr_hw_queues
scsi: ufs: core: Rename symbol sizeof_utp_transfer_cmd_desc()
scsi: ufs: core: Fix MCQ tag calculation
|
|
This fixes the follwing compiler warning reported by kernel test robot:
drivers/bluetooth/btnxpuart.c:1332:34: warning: unused variable
'nxpuart_of_match_table' [-Wunused-const-variable]
Signed-off-by: Neeraj Sanjay Kale <[email protected]>
Reported-by: kernel test robot <[email protected]>
Link: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Currently, hci_conn_del calls hci_conn_unlink for BR/EDR, (e)SCO, and
CIS connections, i.e., everything except LE connections. However, if
(e)SCO connections are unlinked when BR/EDR disconnects, CIS connections
should also be unlinked when LE disconnects.
In terms of disconnection behavior, CIS and (e)SCO connections are not
too different. One peculiarity of CIS is that when CIS connections are
disconnected, the CIS handle isn't deleted, as per [BLUETOOTH CORE
SPECIFICATION Version 5.4 | Vol 4, Part E] 7.1.6 Disconnect command:
All SCO, eSCO, and CIS connections on a physical link should be
disconnected before the ACL connection on the same physical
connection is disconnected. If it does not, they will be
implicitly disconnected as part of the ACL disconnection.
...
Note: As specified in Section 7.7.5, on the Central, the handle
for a CIS remains valid even after disconnection and, therefore,
the Host can recreate a disconnected CIS at a later point in
time using the same connection handle.
Since hci_conn_link invokes both hci_conn_get and hci_conn_hold,
hci_conn_unlink should perform both hci_conn_put and hci_conn_drop as
well. However, currently it performs only hci_conn_put.
This patch makes hci_conn_unlink call hci_conn_drop as well, which
simplifies the logic in hci_conn_del a bit and may benefit future users
of hci_conn_unlink. But it is noted that this change additionally
implies that hci_conn_unlink can queue disc_work on conn itself, with
the following call stack:
hci_conn_unlink(conn) [conn->parent == NULL]
-> hci_conn_unlink(child) [child->parent == conn]
-> hci_conn_drop(child->parent)
-> queue_delayed_work(&conn->disc_work)
Queued disc_work after hci_conn_del can be spurious, so during the
process of hci_conn_del, it is necessary to make the call to
cancel_delayed_work(&conn->disc_work) after invoking hci_conn_unlink.
Signed-off-by: Ruihan Li <[email protected]>
Co-developed-by: Luiz Augusto von Dentz <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Commit 06149746e720 ("Bluetooth: hci_conn: Add support for linking
multiple hcon") reintroduced a previously fixed bug [1] ("KASAN:
slab-use-after-free Read in hci_conn_hash_flush"). This bug was
originally fixed by commit 5dc7d23e167e ("Bluetooth: hci_conn: Fix
possible UAF").
The hci_conn_unlink function was added to avoid invalidating the link
traversal caused by successive hci_conn_del operations releasing extra
connections. However, currently hci_conn_unlink itself also releases
extra connections, resulted in the reintroduced bug.
This patch follows a more robust solution for cleaning up all
connections, by repeatedly removing the first connection until there are
none left. This approach does not rely on the inner workings of
hci_conn_del and ensures proper cleanup of all connections.
Meanwhile, we need to make sure that hci_conn_del never fails. Indeed it
doesn't, as it now always returns zero. To make this a bit clearer, this
patch also changes its return type to void.
Reported-by: [email protected]
Closes: https://lore.kernel.org/linux-bluetooth/[email protected]/
Fixes: 06149746e720 ("Bluetooth: hci_conn: Add support for linking multiple hcon")
Signed-off-by: Ruihan Li <[email protected]>
Co-developed-by: Luiz Augusto von Dentz <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
If hci_conn_put(conn->parent) reduces conn->parent's reference count to
zero, it can immediately deallocate conn->parent. At the same time,
conn->link->list has its head in conn->parent, causing use-after-free
problems in the latter list_del_rcu(&conn->link->list).
This problem can be easily solved by reordering the two operations,
i.e., first performing the list removal with list_del_rcu and then
decreasing the refcnt with hci_conn_put.
Reported-by: Luiz Augusto von Dentz <[email protected]>
Closes: https://lore.kernel.org/linux-bluetooth/CABBYNZ+1kce8_RJrLNOXd_8=Mdpb=2bx4Nto-hFORk=qiOkoCg@mail.gmail.com/
Fixes: 06149746e720 ("Bluetooth: hci_conn: Add support for linking multiple hcon")
Signed-off-by: Ruihan Li <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
The hci_conn_unlink function is being called by hci_conn_del, which
means it should not call hci_conn_del with the input parameter conn
again. If it does, conn may have already been released when
hci_conn_unlink returns, leading to potential UAF and double-free
issues.
This patch resolves the problem by modifying hci_conn_unlink to release
only conn's child links when necessary, but never release conn itself.
Reported-by: [email protected]
Closes: https://lore.kernel.org/linux-bluetooth/[email protected]/
Fixes: 06149746e720 ("Bluetooth: hci_conn: Add support for linking multiple hcon")
Signed-off-by: Ruihan Li <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Reported-by: [email protected]
Reported-by: Luiz Augusto von Dentz <[email protected]>
Reported-by: [email protected]
|
|
kfree()-ing the scratch page isn't enough, we also need to set the pointer
back to NULL to avoid a double-free in the case of a resend.
Fixes: fbd2a05f29a9 (NFSv4.2: Rework scratch handling for READ_PLUS)
Signed-off-by: Anna Schumaker <[email protected]>
|
|
Some calls to rpc_exit_task() may deliberately change the value of
task->tk_status, for instance because it gets checked by the RPC call's
rpc_release() callback. That makes it wrong to reset the value to
task->tk_rpc_status.
In particular this causes a bug where the rpc_call_done() callback tries
to fail over a set of pNFS/flexfiles writes to a different IP address,
but the reset of task->tk_status causes nfs_commit_release_pages() to
immediately mark the file as having a fatal error.
Fixes: 39494194f93b ("SUNRPC: Fix races with rpc_killall_tasks()")
Cc: [email protected] # 6.1.x
Signed-off-by: Trond Myklebust <[email protected]>
Signed-off-by: Anna Schumaker <[email protected]>
|
|
kmap_atomic() is deprecated in favor of kmap_local_{folio,page}().
Therefore, replace kmap_atomic() with kmap_local_folio() in
nfs_readdir_folio_array_append().
kmap_atomic() disables page-faults and preemption (the latter only for
!PREEMPT_RT kernels), However, the code within the mapping/un-mapping in
nfs_readdir_folio_array_append() does not depend on the above-mentioned
side effects.
Therefore, a mere replacement of the old API with the new one is all that
is required (i.e., there is no need to explicitly add any calls to
pagefault_disable() and/or preempt_disable()).
Tested with (x)fstests in a QEMU/KVM x86_32 VM, 6GB RAM, booting a kernel
with HIGHMEM64GB enabled.
Cc: Ira Weiny <[email protected]>
Signed-off-by: Fabio M. De Francesco <[email protected]>
Fixes: ec108d3cc766 ("NFS: Convert readdir page array functions to use a folio")
Signed-off-by: Anna Schumaker <[email protected]>
|
|
Pull ceph fixes from Ilya Dryomov:
"A workaround for a just discovered bug in MClientSnap encoding which
goes back to 2017 (marked for stable) and a fixup to quieten a static
checker"
* tag 'ceph-for-6.4-rc3' of https://github.com/ceph/ceph-client:
ceph: force updating the msg pointer in non-split case
ceph: silence smatch warning in reconnect_caps_cb()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two issues in the cpupower utility and get rid of a spurious
warning message printed to the kernel log by the ACPI cpufreq driver
after recent changes.
Specifics:
- Get rid of a warning message printed by the ACPI cpufreq driver
after recent changes in it when anohter CPU performance scaling
driver is registered already when it starts (Petr Pavlu)
- Make cpupower read TSC on each CPU right before reading MPERF so as
to reduce the potential time difference between the TSC and MPERF
accesses and improve the C0 percentage calculation (Wyes Karny)
- Fix a possible file handle leak and clean up the code in the
sysfs_get_enabled() function in cpupower (Hao Zeng)"
* tag 'pm-6.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: ACPI: Prevent a warning when another frequency driver is loaded
cpupower: Make TSC read per CPU for Mperf monitor
cpupower:Fix resource leaks in sysfs_get_enabled()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Add an ACPI IRQ override quirk for LG UltraPC 17U70P so as to make the
internal keyboard work on that machine (Rubén Gómez)"
* tag 'acpi-6.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: resource: Add IRQ override quirk for LG UltraPC 17U70P
|
|
Pull documentation fixes from Jonathan Corbet:
"Four straightforward documentation fixes"
* tag 'docs-6.4-fixes' of git://git.lwn.net/linux:
Documentation/filesystems: ramfs-rootfs-initramfs: use :Author:
Documentation/filesystems: sharedsubtree: add section headings
docs: quickly-build-trimmed-linux: various small fixes and improvements
Documentation: use capitalization for chapters and acronyms
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Alexander Gordeev:
- Add check whether the required facilities are installed before using
the s390-specific ChaCha20 implementation
- Key blobs for s390 protected key interface IOCTLs commands
PKEY_VERIFYKEY2 and PKEY_VERIFYKEY3 may contain clear key material.
Zeroize copies of these keys in kernel memory after creating
protected keys
- Set CONFIG_INIT_STACK_NONE=y in defconfigs to avoid extra overhead of
initializing all stack variables by default
- Make sure that when a new channel-path is enabled all subchannels are
evaluated: with and without any devices connected on it
- When SMT thread CPUs are added to CPU topology masks the nr_cpu_ids
limit is not checked and could be exceeded. Respect the nr_cpu_ids
limit and avoid a warning when CONFIG_DEBUG_PER_CPU_MAPS is set
- The pointer to IPL Parameter Information Block is stored in the
absolute lowcore as a virtual address. Save it as the physical
address for later use by dump tools
- Fix a Queued Direct I/O (QDIO) problem on z/VM guests using QIOASSIST
with dedicated (pass through) QDIO-based devices such as FCP, real
OSA or HiperSockets
- s390's struct statfs and struct statfs64 contain padding, which
field-by-field copying does not set. Initialize the respective
structures with zeros before filling them and copying to userspace
- Grow s390 compat_statfs64, statfs and statfs64 structures f_spare
array member to cover padding and simplify things
- Remove obsolete SCHED_BOOK and SCHED_DRAWER configs
- Remove unneeded S390_CCW_IOMMU and S390_AP_IOM configs
* tag 's390-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/iommu: get rid of S390_CCW_IOMMU and S390_AP_IOMMU
s390/Kconfig: remove obsolete configs SCHED_{BOOK,DRAWER}
s390/uapi: cover statfs padding by growing f_spare
statfs: enforce statfs[64] structure initialization
s390/qdio: fix do_sqbs() inline assembly constraint
s390/ipl: fix IPIB virtual vs physical address confusion
s390/topology: honour nr_cpu_ids when adding CPUs
s390/cio: include subchannels without devices also for evaluation
s390/defconfigs: set CONFIG_INIT_STACK_NONE=y
s390/pkey: zeroize key blobs
s390/crypto: use vector instructions only if available for ChaCha20
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A mixture of compiler/static checker resolutions and a couple of MTE
fixes:
- Avoid erroneously marking untagged pages with PG_mte_tagged
- Always reset KASAN tags for destination page in copy_page()
- Mark PMU header functions 'static inline'
- Fix some sparse warnings due to missing casts"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mte: Do not set PG_mte_tagged if tags were not initialized
arm64: Also reset KASAN tag if page is not PG_mte_tagged
arm64: perf: Mark all accessor functions inline
ARM: perf: Mark all accessor functions inline
arm64: vdso: Pass (void *) to virt_to_page()
arm64/mm: mark private VM_FAULT_X defines as vm_fault_t
|
|
In kvm_vm_ioctl_create_vcpu(), add vcpu to vcpu_array iff it's safe to
access vcpu via kvm_get_vcpu() and kvm_for_each_vcpu(), i.e. when there's
no failure path requiring vcpu removal and destruction. Such order is
important because vcpu_array accessors may end up referencing vcpu at
vcpu_array[0] even before online_vcpus is set to 1.
When online_vcpus=0, any call to kvm_get_vcpu() goes through
array_index_nospec() and ends with an attempt to xa_load(vcpu_array, 0):
int num_vcpus = atomic_read(&kvm->online_vcpus);
i = array_index_nospec(i, num_vcpus);
return xa_load(&kvm->vcpu_array, i);
Similarly, when online_vcpus=0, a kvm_for_each_vcpu() does not iterate over
an "empty" range, but actually [0, ULONG_MAX]:
xa_for_each_range(&kvm->vcpu_array, idx, vcpup, 0, \
(atomic_read(&kvm->online_vcpus) - 1))
In both cases, such online_vcpus=0 edge case, even if leading to
unnecessary calls to XArray API, should not be an issue; requesting
unpopulated indexes/ranges is handled by xa_load() and xa_for_each_range().
However, this means that when the first vCPU is created and inserted in
vcpu_array *and* before online_vcpus is incremented, code calling
kvm_get_vcpu()/kvm_for_each_vcpu() already has access to that first vCPU.
This should not pose a problem assuming that once a vcpu is stored in
vcpu_array, it will remain there, but that's not the case:
kvm_vm_ioctl_create_vcpu() first inserts to vcpu_array, then requests a
file descriptor. If create_vcpu_fd() fails, newly inserted vcpu is removed
from the vcpu_array, then destroyed:
vcpu->vcpu_idx = atomic_read(&kvm->online_vcpus);
r = xa_insert(&kvm->vcpu_array, vcpu->vcpu_idx, vcpu, GFP_KERNEL_ACCOUNT);
kvm_get_kvm(kvm);
r = create_vcpu_fd(vcpu);
if (r < 0) {
xa_erase(&kvm->vcpu_array, vcpu->vcpu_idx);
kvm_put_kvm_no_destroy(kvm);
goto unlock_vcpu_destroy;
}
atomic_inc(&kvm->online_vcpus);
This results in a possible race condition when a reference to a vcpu is
acquired (via kvm_get_vcpu() or kvm_for_each_vcpu()) moments before said
vcpu is destroyed.
Signed-off-by: Michal Luczaj <[email protected]>
Message-Id: <[email protected]>
Cc: [email protected]
Fixes: c5b077549136 ("KVM: Convert the kvm->vcpus array to a xarray", 2021-12-08)
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
Include a definition of WARN_ON_ONCE() before using it.
Fixes: bb1fcc70d98f ("KVM: nVMX: Allow L1 to use 5-level page walks for nested EPT")
Cc: Sean Christopherson <[email protected]>
Signed-off-by: Jacob Xu <[email protected]>
[reworded commit message; changed <asm/bug.h> to <linux/bug.h>]
Signed-off-by: Jim Mattson <[email protected]>
Reviewed-by: Sean Christopherson <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
Reject hardware enabling, i.e. VM creation, if a restart/shutdown has
been initiated to avoid re-enabling hardware between kvm_reboot() and
machine_{halt,power_off,restart}(). The restart case is especially
problematic (for x86) as enabling VMX (or clearing GIF in KVM_RUN on
SVM) blocks INIT, which results in the restart/reboot hanging as BIOS
is unable to wake and rendezvous with APs.
Note, this bug, and the original issue that motivated the addition of
kvm_reboot(), is effectively limited to a forced reboot, e.g. `reboot -f`.
In a "normal" reboot, userspace will gracefully teardown userspace before
triggering the kernel reboot (modulo bugs, errors, etc), i.e. any process
that might do ioctl(KVM_CREATE_VM) is long gone.
Fixes: 8e1c18157d87 ("KVM: VMX: Disable VMX when system shutdown")
Signed-off-by: Sean Christopherson <[email protected]>
Acked-by: Marc Zyngier <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
Use syscore_ops.shutdown to disable hardware virtualization during a
reboot instead of using the dedicated reboot_notifier so that KVM disables
virtualization _after_ system_state has been updated. This will allow
fixing a race in KVM's handling of a forced reboot where KVM can end up
enabling hardware virtualization between kernel_restart_prepare() and
machine_restart().
Rename KVM's hook to match the syscore op to avoid any possible confusion
from wiring up a "reboot" helper to a "shutdown" hook (neither "shutdown
nor "reboot" is completely accurate as the hook handles both).
Opportunistically rewrite kvm_shutdown()'s comment to make it less VMX
specific, and to explain why kvm_rebooting exists.
Cc: Marc Zyngier <[email protected]>
Cc: Oliver Upton <[email protected]>
Cc: James Morse <[email protected]>
Cc: Suzuki K Poulose <[email protected]>
Cc: Zenghui Yu <[email protected]>
Cc: [email protected]
Cc: Huacai Chen <[email protected]>
Cc: Aleksandar Markovic <[email protected]>
Cc: Anup Patel <[email protected]>
Cc: Atish Patra <[email protected]>
Cc: [email protected]
Signed-off-by: Sean Christopherson <[email protected]>
Acked-by: Marc Zyngier <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes that have been gathered since rc1:
- Lots of small ASoC SOF Intel fixes
- A couple of UAF and NULL-dereference fixes
- Quirks and updates for HD-audio, USB-audio and ASoC AMD
- A few minor build / sparse warning fixes
- MAINTAINERS and DT updates"
* tag 'sound-6.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (38 commits)
ALSA: hda: Add NVIDIA codec IDs a3 through a7 to patch table
ALSA: oss: avoid missing-prototype warnings
ALSA: cs46xx: mark snd_cs46xx_download_image as static
ALSA: hda: Fix Oops by 9.1 surround channel names
ASoC: SOF: topology: Fix tuples array allocation
ASoC: SOF: Separate the tokens for input and output pin index
MAINTAINERS: Remove self from Cirrus Codec drivers
ASoC: cs35l56: Prevent unbalanced pm_runtime in dsp_work() on SoundWire
ASoC: SOF: topology: Fix logic for copying tuples
ASoC: SOF: pm: save io region state in case of errors in resume
ASoC: MAINTAINERS: drop Krzysztof Kozlowski from Samsung audio
ASoC: mediatek: mt8186: Fix use-after-free in driver remove path
ASoC: SOF: ipc3-topology: Make sure that only one cmd is sent in dai_config
ASoC: SOF: sof-client-probes: fix pm_runtime imbalance in error handling
ASoC: SOF: pcm: fix pm_runtime imbalance in error handling
ASoC: SOF: debug: conditionally bump runtime_pm counter on exceptions
ASoC: SOF: Intel: hda-mlink: add helper to program SoundWire PCMSyCM registers
ASoC: SOF: Intel: hda-mlink: initialize instance_offset member
ASoC: SOF: Intel: hda-mlink: use 'ml_addr' parameter consistently
ASoC: SOF: Intel: hda-mlink: fix base_ptr computation
...
|
|
Initialize eswitch instance for a function which is eswitch manager
but not a vport group manager.
Signed-off-by: Roi Dayan <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Limit the PF related warning to show if device is actually a PF.
Signed-off-by: Roi Dayan <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Use metadata matching for RoCE loopback rule if device is configured
to use metadata for source port matching.
Signed-off-by: Roi Dayan <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Could be port initializing eswitch doesn't support RoCE version 1
but all ports should support RoCE version 2.
Signed-off-by: Roi Dayan <[email protected]>
Reviewed-by: Maor Gottlieb <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
If log_max_l2_table is 0 there is no really room for one L2 address.
and should be treated as not supported.
Do the check in MPFS init and for vport context events which
both used to update L2 address.
Signed-off-by: Roi Dayan <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|