aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2017-11-27i2c: i801: Fix Failed to allocate irq -2147483648 errorHans de Goede1-0/+3
On Apollo Lake devices the BIOS does not set up IRQ routing for the i801 SMBUS controller IRQ, so we end up with dev->irq set to IRQ_NOTCONNECTED. Detect this and do not try to use the irq in this case silencing: i801_smbus 0000:00:1f.1: Failed to allocate irq -2147483648: -107 Cc: [email protected] BugLink: https://communities.intel.com/thread/114759 Signed-off-by: Hans de Goede <[email protected]> Reviewed-by: Jean Delvare <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2017-11-27xfs: log recovery should replay deferred ops in orderDarrick J. Wong5-40/+85
As part of testing log recovery with dm_log_writes, Amir Goldstein discovered an error in the deferred ops recovery that lead to corruption of the filesystem metadata if a reflink+rmap filesystem happened to shut down midway through a CoW remap: "This is what happens [after failed log recovery]: "Phase 1 - find and verify superblock... "Phase 2 - using internal log " - zero log... " - scan filesystem freespace and inode maps... " - found root inode chunk "Phase 3 - for each AG... " - scan (but don't clear) agi unlinked lists... " - process known inodes and perform inode discovery... " - agno = 0 "data fork in regular inode 134 claims CoW block 376 "correcting nextents for inode 134 "bad data fork in inode 134 "would have cleared inode 134" Hou Tao dissected the log contents of exactly such a crash: "According to the implementation of xfs_defer_finish(), these ops should be completed in the following sequence: "Have been done: "(1) CUI: Oper (160) "(2) BUI: Oper (161) "(3) CUD: Oper (194), for CUI Oper (160) "(4) RUI A: Oper (197), free rmap [0x155, 2, -9] "Should be done: "(5) BUD: for BUI Oper (161) "(6) RUI B: add rmap [0x155, 2, 137] "(7) RUD: for RUI A "(8) RUD: for RUI B "Actually be done by xlog_recover_process_intents() "(5) BUD: for BUI Oper (161) "(6) RUI B: add rmap [0x155, 2, 137] "(7) RUD: for RUI B "(8) RUD: for RUI A "So the rmap entry [0x155, 2, -9] for COW should be freed firstly, then a new rmap entry [0x155, 2, 137] will be added. However, as we can see from the log record in post_mount.log (generated after umount) and the trace print, the new rmap entry [0x155, 2, 137] are added firstly, then the rmap entry [0x155, 2, -9] are freed." When reconstructing the internal log state from the log items found on disk, it's required that deferred ops replay in exactly the same order that they would have had the filesystem not gone down. However, replaying unfinished deferred ops can create /more/ deferred ops. These new deferred ops are finished in the wrong order. This causes fs corruption and replay crashes, so let's create a single defer_ops to handle the subsequent ops created during replay, then use one single transaction at the end of log recovery to ensure that everything is replayed in the same order as they're supposed to be. Reported-by: Amir Goldstein <[email protected]> Analyzed-by: Hou Tao <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Tested-by: Amir Goldstein <[email protected]> Signed-off-by: Darrick J. Wong <[email protected]>
2017-11-27xfs: always free inline data before resetting inode fork during ifreeDarrick J. Wong1-0/+21
In xfs_ifree, we reset the data/attr forks to extents format without bothering to free any inline data buffer that might still be around after all the blocks have been truncated off the file. Prior to commit 43518812d2 ("xfs: remove support for inlining data/extents into the inode fork") nobody noticed because the leftover inline data after truncation was small enough to fit inside the inline buffer inside the fork itself. However, now that we've removed the inline buffer, we /always/ have to free the inline data buffer or else we leak them like crazy. This test was found by turning on kmemleak for generic/001 or generic/388. Signed-off-by: Darrick J. Wong <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]>
2017-11-27Merge tag 'kvm-ppc-fixes-4.15-1' of ↵Paolo Bonzini3-16/+25
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master PPC KVM fixes for 4.15 One commit here, that fixes a couple of bugs relating to the patch series that enables HPT guests to run on a radix host on POWER9 systems. This patch series went upstream in the 4.15 merge window, so no stable backport is required.
2017-11-27KVM: Let KVM_SET_SIGNAL_MASK work as advertisedJan H. Schönherr7-25/+37
KVM API says for the signal mask you set via KVM_SET_SIGNAL_MASK, that "any unblocked signal received [...] will cause KVM_RUN to return with -EINTR" and that "the signal will only be delivered if not blocked by the original signal mask". This, however, is only true, when the calling task has a signal handler registered for a signal. If not, signal evaluation is short-circuited for SIG_IGN and SIG_DFL, and the signal is either ignored without KVM_RUN returning or the whole process is terminated. Make KVM_SET_SIGNAL_MASK behave as advertised by utilizing logic similar to that in do_sigtimedwait() to avoid short-circuiting of signals. Signed-off-by: Jan H. Schönherr <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2017-11-27Btrfs: fix list_add corruption and soft lockups in fsyncLiu Bo2-3/+4
Xfstests btrfs/146 revealed this corruption, [ 58.138831] Buffer I/O error on dev dm-0, logical block 2621424, async page read [ 58.151233] BTRFS error (device sdf): bdev /dev/mapper/error-test errs: wr 1, rd 0, flush 0, corrupt 0, gen 0 [ 58.152403] list_add corruption. prev->next should be next (ffff88005e6775d8), but was ffffc9000189be88. (prev=ffffc9000189be88). [ 58.153518] ------------[ cut here ]------------ [ 58.153892] WARNING: CPU: 1 PID: 1287 at lib/list_debug.c:31 __list_add_valid+0x169/0x1f0 ... [ 58.157379] RIP: 0010:__list_add_valid+0x169/0x1f0 ... [ 58.161956] Call Trace: [ 58.162264] btrfs_log_inode_parent+0x5bd/0xfb0 [btrfs] [ 58.163583] btrfs_log_dentry_safe+0x60/0x80 [btrfs] [ 58.164003] btrfs_sync_file+0x4c2/0x6f0 [btrfs] [ 58.164393] vfs_fsync_range+0x5f/0xd0 [ 58.164898] do_fsync+0x5a/0x90 [ 58.165170] SyS_fsync+0x10/0x20 [ 58.165395] entry_SYSCALL_64_fastpath+0x1f/0xbe ... It turns out that we could record btrfs_log_ctx:io_err in log_one_extents when IO fails, but make log_one_extents() return '0' instead of -EIO, so the IO error is not acknowledged by the callers, i.e. btrfs_log_inode_parent(), which would remove btrfs_log_ctx:list from list head 'root->log_ctxs'. Since btrfs_log_ctx is allocated from stack memory, it'd get freed with a object alive on the list. then a future list_add will throw the above warning. This returns the correct error in the above case. Jeff also reported this while testing against his fsync error patch set[1]. [1]: https://www.spinics.net/lists/linux-btrfs/msg65308.html "btrfs list corruption and soft lockups while testing writeback error handling" Fixes: 8407f553268a4611f254 ("Btrfs: fix data corruption after fast fsync and writeback error") Signed-off-by: Liu Bo <[email protected]> Reviewed-by: David Sterba <[email protected]> Signed-off-by: David Sterba <[email protected]>
2017-11-27KVM: VMX: Fix vmx->nested freeing when no SMI handlerWanpeng Li1-1/+2
Reported by syzkaller: ------------[ cut here ]------------ WARNING: CPU: 5 PID: 2939 at arch/x86/kvm/vmx.c:3844 free_loaded_vmcs+0x77/0x80 [kvm_intel] CPU: 5 PID: 2939 Comm: repro Not tainted 4.14.0+ #26 RIP: 0010:free_loaded_vmcs+0x77/0x80 [kvm_intel] Call Trace: vmx_free_vcpu+0xda/0x130 [kvm_intel] kvm_arch_destroy_vm+0x192/0x290 [kvm] kvm_put_kvm+0x262/0x560 [kvm] kvm_vm_release+0x2c/0x30 [kvm] __fput+0x190/0x370 task_work_run+0xa1/0xd0 do_exit+0x4d2/0x13e0 do_group_exit+0x89/0x140 get_signal+0x318/0xb80 do_signal+0x8c/0xb40 exit_to_usermode_loop+0xe4/0x140 syscall_return_slowpath+0x206/0x230 entry_SYSCALL_64_fastpath+0x98/0x9a The syzkaller testcase will execute VMXON/VMLAUCH instructions, so the vmx->nested stuff is populated, it will also issue KVM_SMI ioctl. However, the testcase is just a simple c program and not be lauched by something like seabios which implements smi_handler. Commit 05cade71cf (KVM: nSVM: fix SMI injection in guest mode) gets out of guest mode and set nested.vmxon to false for the duration of SMM according to SDM 34.14.1 "leave VMX operation" upon entering SMM. We can't alloc/free the vmx->nested stuff each time when entering/exiting SMM since it will induce more overhead. So the function vmx_pre_enter_smm() marks nested.vmxon false even if vmx->nested stuff is still populated. What it expected is em_rsm() can mark nested.vmxon to be true again. However, the smi_handler/rsm will not execute since there is no something like seabios in this scenario. The function free_nested() fails to free the vmx->nested stuff since the vmx->nested.vmxon is false which results in the above warning. This patch fixes it by also considering the no SMI handler case, luckily vmx->nested.smm.vmxon is marked according to the value of vmx->nested.vmxon in vmx_pre_enter_smm(), we can take advantage of it and free vmx->nested stuff when L1 goes down. Reported-by: Dmitry Vyukov <[email protected]> Cc: Paolo Bonzini <[email protected]> Cc: Radim Krčmář <[email protected]> Cc: Dmitry Vyukov <[email protected]> Reviewed-by: Liran Alon <[email protected]> Fixes: 05cade71cf (KVM: nSVM: fix SMI injection in guest mode) Signed-off-by: Wanpeng Li <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2017-11-27KVM: VMX: Fix rflags cache during vCPU resetWanpeng Li1-1/+1
Reported by syzkaller: *** Guest State *** CR0: actual=0x0000000080010031, shadow=0x0000000060000010, gh_mask=fffffffffffffff7 CR4: actual=0x0000000000002061, shadow=0x0000000000000000, gh_mask=ffffffffffffe8f1 CR3 = 0x000000002081e000 RSP = 0x000000000000fffa RIP = 0x0000000000000000 RFLAGS=0x00023000 DR7 = 0x00000000000000 ^^^^^^^^^^ ------------[ cut here ]------------ WARNING: CPU: 6 PID: 24431 at /home/kernel/linux/arch/x86/kvm//x86.c:7302 kvm_arch_vcpu_ioctl_run+0x651/0x2ea0 [kvm] CPU: 6 PID: 24431 Comm: reprotest Tainted: G W OE 4.14.0+ #26 RIP: 0010:kvm_arch_vcpu_ioctl_run+0x651/0x2ea0 [kvm] RSP: 0018:ffff880291d179e0 EFLAGS: 00010202 Call Trace: kvm_vcpu_ioctl+0x479/0x880 [kvm] do_vfs_ioctl+0x142/0x9a0 SyS_ioctl+0x74/0x80 entry_SYSCALL_64_fastpath+0x23/0x9a The failed vmentry is triggered by the following beautified testcase: #include <unistd.h> #include <sys/syscall.h> #include <string.h> #include <stdint.h> #include <linux/kvm.h> #include <fcntl.h> #include <sys/ioctl.h> long r[5]; int main() { struct kvm_debugregs dr = { 0 }; r[2] = open("/dev/kvm", O_RDONLY); r[3] = ioctl(r[2], KVM_CREATE_VM, 0); r[4] = ioctl(r[3], KVM_CREATE_VCPU, 7); struct kvm_guest_debug debug = { .control = 0xf0403, .arch = { .debugreg[6] = 0x2, .debugreg[7] = 0x2 } }; ioctl(r[4], KVM_SET_GUEST_DEBUG, &debug); ioctl(r[4], KVM_RUN, 0); } which testcase tries to setup the processor specific debug registers and configure vCPU for handling guest debug events through KVM_SET_GUEST_DEBUG. The KVM_SET_GUEST_DEBUG ioctl will get and set rflags in order to set TF bit if single step is needed. All regs' caches are reset to avail and GUEST_RFLAGS vmcs field is reset to 0x2 during vCPU reset. However, the cache of rflags is not reset during vCPU reset. The function vmx_get_rflags() returns an unreset rflags cache value since the cache is marked avail, it is 0 after boot. Vmentry fails if the rflags reserved bit 1 is 0. This patch fixes it by resetting both the GUEST_RFLAGS vmcs field and its cache to 0x2 during vCPU reset. Reported-by: Dmitry Vyukov <[email protected]> Tested-by: Dmitry Vyukov <[email protected]> Reviewed-by: David Hildenbrand <[email protected]> Cc: Paolo Bonzini <[email protected]> Cc: Radim Krčmář <[email protected]> Cc: Nadav Amit <[email protected]> Cc: Dmitry Vyukov <[email protected]> Signed-off-by: Wanpeng Li <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2017-11-27KVM: X86: Fix softlockup when get the current kvmclockWanpeng Li1-4/+7
watchdog: BUG: soft lockup - CPU#6 stuck for 22s! [qemu-system-x86:10185] CPU: 6 PID: 10185 Comm: qemu-system-x86 Tainted: G OE 4.14.0-rc4+ #4 RIP: 0010:kvm_get_time_scale+0x4e/0xa0 [kvm] Call Trace: get_time_ref_counter+0x5a/0x80 [kvm] kvm_hv_process_stimers+0x120/0x5f0 [kvm] kvm_arch_vcpu_ioctl_run+0x4b4/0x1690 [kvm] kvm_vcpu_ioctl+0x33a/0x620 [kvm] do_vfs_ioctl+0xa1/0x5d0 SyS_ioctl+0x79/0x90 entry_SYSCALL_64_fastpath+0x1e/0xa9 This can be reproduced when running kvm-unit-tests/hyperv_stimer.flat and cpu-hotplug stress simultaneously. __this_cpu_read(cpu_tsc_khz) returns 0 (set in kvmclock_cpu_down_prep()) when the pCPU is unhotplug which results in kvm_get_time_scale() gets into an infinite loop. This patch fixes it by treating the unhotplug pCPU as not using master clock. Reviewed-by: Radim Krčmář <[email protected]> Reviewed-by: David Hildenbrand <[email protected]> Cc: Paolo Bonzini <[email protected]> Cc: Radim Krčmář <[email protected]> Signed-off-by: Wanpeng Li <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2017-11-27KVM: lapic: Fixup LDR on load in x2apicDr. David Alan Gilbert1-0/+5
In x2apic mode the LDR is fixed based on the ID rather than separately loadable like it was before x2. When kvm_apic_set_state is called, the base is set, and if it has the X2APIC_ENABLE flag set then the LDR is calculated; however that value gets overwritten by the memcpy a few lines below overwriting it with the value that came from userland. The symptom is a lack of EOI after loading the state (e.g. after a QEMU migration) and is due to the EOI bitmap being wrong due to the incorrect LDR. This was seen with a Win2016 guest under Qemu with irqchip=split whose USB mouse didn't work after a VM migration. This corresponds to RH bug: https://bugzilla.redhat.com/show_bug.cgi?id=1502591 Reported-by: Yiqian Wei <[email protected]> Signed-off-by: Dr. David Alan Gilbert <[email protected]> Cc: [email protected] [Applied fixup from Liran Alon. - Paolo] Signed-off-by: Paolo Bonzini <[email protected]>
2017-11-27KVM: lapic: Split out x2apic ldr calculationDr. David Alan Gilbert1-1/+6
Split out the ldr calculation from kvm_apic_set_x2apic_id since we're about to reuse it in the following patch. Signed-off-by: Dr. David Alan Gilbert <[email protected]> Cc: [email protected] Signed-off-by: Paolo Bonzini <[email protected]>
2017-11-27reiserfs: remove unneeded i_version bumpJeff Layton1-1/+0
The i_version field in reiserfs is not initialized and is only ever updated here. Nothing ever views it, so just remove it. Signed-off-by: Jeff Layton <[email protected]> Signed-off-by: Jan Kara <[email protected]>
2017-11-28Merge tag 'mac80211-for-davem-2017-11-27' of ↵David S. Miller10-17/+61
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Four fixes: * CRYPTO_SHA256 is needed for regdb validation * mac80211: mesh path metric was wrong in some frames * mac80211: use QoS null-data packets on QoS connections * mac80211: tear down RX aggregation sessions first to drop fewer packets in HW restart scenarios ==================== Signed-off-by: David S. Miller <[email protected]>
2017-11-27btrfs: Fix wild memory access in compression level parserQu Wenruo3-3/+14
[BUG] Kernel panic when mounting with "-o compress" mount option. KASAN will report like: ------ ================================================================== BUG: KASAN: wild-memory-access in strncmp+0x31/0xc0 Read of size 1 at addr d86735fce994f800 by task mount/662 ... Call Trace: dump_stack+0xe3/0x175 kasan_report+0x163/0x370 __asan_load1+0x47/0x50 strncmp+0x31/0xc0 btrfs_compress_str2level+0x20/0x70 [btrfs] btrfs_parse_options+0xff4/0x1870 [btrfs] open_ctree+0x2679/0x49f0 [btrfs] btrfs_mount+0x1b7f/0x1d30 [btrfs] mount_fs+0x49/0x190 vfs_kern_mount.part.29+0xba/0x280 vfs_kern_mount+0x13/0x20 btrfs_mount+0x31e/0x1d30 [btrfs] mount_fs+0x49/0x190 vfs_kern_mount.part.29+0xba/0x280 do_mount+0xaad/0x1a00 SyS_mount+0x98/0xe0 entry_SYSCALL_64_fastpath+0x1f/0xbe ------ [Cause] For 'compress' and 'compress_force' options, its token doesn't expect any parameter so its args[0] contains uninitialized data. Accessing args[0] will cause above wild memory access. [Fix] For Opt_compress and Opt_compress_force, set compression level to the default. Signed-off-by: Qu Wenruo <[email protected]> Reviewed-by: David Sterba <[email protected]> [ set the default in advance ] Signed-off-by: David Sterba <[email protected]>
2017-11-27RISC-V: Add VDSO entries for clock_get/gettimeofday/getcpuAndrew Waterman6-1/+113
For now these are just placeholders that execute the syscall. We will later optimize them to avoid kernel crossings, but we'd like to have the VDSO entries from the first released kernel version to make the ABI simpler. Signed-off-by: Andrew Waterman <[email protected]> Signed-off-by: Palmer Dabbelt <[email protected]>
2017-11-27RISC-V: Remove __vdso_cmpxchg{32,64} symbol versionsPalmer Dabbelt1-2/+0
These were left over from an earlier version of the port. Signed-off-by: Palmer Dabbelt <[email protected]>
2017-11-28Merge branch 'sctp-stream-reconfig-fixes'David S. Miller1-12/+65
Xin Long says: ==================== sctp: a bunch of fixes for stream reconfig This patchset is to make stream reset and asoc reset work more correctly for stream reconfig. Thank to Marcelo making them very clear. ==================== Signed-off-by: David S. Miller <[email protected]>
2017-11-28sctp: set sender next_tsn for the old result with ctsn_ack_point plus 1Xin Long1-1/+1
When doing asoc reset, if the sender of the response has already sent some chunk and increased asoc->next_tsn before the duplicate request comes, the response will use the old result with an incorrect sender next_tsn. Better than asoc->next_tsn, asoc->ctsn_ack_point can't be changed after the sender of the response has performed the asoc reset and before the peer has confirmed it, and it's value is still asoc->next_tsn original value minus 1. This patch sets sender next_tsn for the old result with ctsn_ack_point plus 1 when processing the duplicate request, to make sure the sender next_tsn value peer gets will be always right. Fixes: 692787cef651 ("sctp: implement receiver-side procedures for the SSN/TSN Reset Request Parameter") Signed-off-by: Xin Long <[email protected]> Acked-by: Marcelo Ricardo Leitner <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-11-28sctp: avoid flushing unsent queue when doing asoc resetXin Long1-7/+14
Now when doing asoc reset, it cleans up sacked and abandoned queues by calling sctp_outq_free where it also cleans up unsent, retransmit and transmitted queues. It's safe for the sender of response, as these 3 queues are empty at that time. But when the receiver of response is doing the reset, the users may already enqueue some chunks into unsent during the time waiting the response, and these chunks should not be flushed. To void the chunks in it would be removed, it moves the queue into a temp list, then gets it back after sctp_outq_free is done. The patch also fixes some incorrect comments in sctp_process_strreset_tsnreq. Signed-off-by: Xin Long <[email protected]> Acked-by: Marcelo Ricardo Leitner <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-11-28sctp: only allow the asoc reset when the asoc outq is emptyXin Long1-0/+9
As it says in rfc6525#section5.1.4, before sending the request, C2: The sender has either no outstanding TSNs or considers all outstanding TSNs abandoned. Prior to this patch, it tried to consider all outstanding TSNs abandoned by dropping all chunks in all outqs with sctp_outq_free (even including sacked, retransmit and transmitted queues) when doing this reset, which is too aggressive. To make it work gently, this patch will only allow the asoc reset when the sender has no outstanding TSNs by checking if unsent, transmitted and retransmit are all empty with sctp_outq_is_empty before sending and processing the request. Fixes: 692787cef651 ("sctp: implement receiver-side procedures for the SSN/TSN Reset Request Parameter") Signed-off-by: Xin Long <[email protected]> Acked-by: Marcelo Ricardo Leitner <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-11-28sctp: only allow the out stream reset when the stream outq is emptyXin Long1-0/+35
Now the out stream reset in sctp stream reconf could be done even if the stream outq is not empty. It means that users can not be sure since which msg the new ssn will be used. To make this more synchronous, it shouldn't allow to do out stream reset until these chunks in unsent outq all are sent out. This patch checks the corresponding stream outqs when sending and processing the request . If any of them has unsent chunks in outq, it will return -EAGAIN instead or send SCTP_STRRESET_IN_PROGRESS back to the sender. Fixes: 7f9d68ac944e ("sctp: implement sender-side procedures for SSN Reset Request Parameter") Suggested-by: Marcelo Ricardo Leitner <[email protected]> Signed-off-by: Xin Long <[email protected]> Acked-by: Marcelo Ricardo Leitner <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-11-28sctp: use sizeof(__u16) for each stream number length instead of magic numberXin Long1-4/+6
Now in stream reconf part there are still some places using magic number 2 for each stream number length. To make it more readable, this patch is to replace them with sizeof(__u16). Reported-by: Marcelo Ricardo Leitner <[email protected]> Signed-off-by: Xin Long <[email protected]> Acked-by: Marcelo Ricardo Leitner <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-11-27btrfs: fix deadlock when writing out space cacheJosef Bacik1-1/+2
If we fail to prepare our pages for whatever reason (out of memory in our case) we need to make sure to drop the block_group->data_rwsem, otherwise hilarity ensues. Signed-off-by: Josef Bacik <[email protected]> Reviewed-by: Omar Sandoval <[email protected]> Reviewed-by: Liu Bo <[email protected]> Reviewed-by: David Sterba <[email protected]> [ add label and use existing unlocking code ] Signed-off-by: David Sterba <[email protected]>
2017-11-27usb: bdc: fix platform_no_drv_owner.cocci warningsVasyl Gomonovych1-1/+0
Remove .owner field if calls are used which set it automatically drivers/usb/gadget/udc/bdc/bdc_core.c:645:3-8: No need to set .owner here. The core will do it. Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Signed-off-by: Vasyl Gomonovych <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-11-27usb: gadget: ffs: Forbid usb_ep_alloc_request from sleepingVincent Pelletier1-1/+1
Found using DEBUG_ATOMIC_SLEEP while submitting an AIO read operation: [ 100.853642] BUG: sleeping function called from invalid context at mm/slab.h:421 [ 100.861148] in_atomic(): 1, irqs_disabled(): 1, pid: 1880, name: python [ 100.867954] 2 locks held by python/1880: [ 100.867961] #0: (&epfile->mutex){....}, at: [<f8188627>] ffs_mutex_lock+0x27/0x30 [usb_f_fs] [ 100.868020] #1: (&(&ffs->eps_lock)->rlock){....}, at: [<f818ad4b>] ffs_epfile_io.isra.17+0x24b/0x590 [usb_f_fs] [ 100.868076] CPU: 1 PID: 1880 Comm: python Not tainted 4.14.0-edison+ #118 [ 100.868085] Hardware name: Intel Corporation Merrifield/BODEGA BAY, BIOS 542 2015.01.21:18.19.48 [ 100.868093] Call Trace: [ 100.868122] dump_stack+0x47/0x62 [ 100.868156] ___might_sleep+0xfd/0x110 [ 100.868182] __might_sleep+0x68/0x70 [ 100.868217] kmem_cache_alloc_trace+0x4b/0x200 [ 100.868248] ? dwc3_gadget_ep_alloc_request+0x24/0xe0 [dwc3] [ 100.868302] dwc3_gadget_ep_alloc_request+0x24/0xe0 [dwc3] [ 100.868343] usb_ep_alloc_request+0x16/0xc0 [udc_core] [ 100.868386] ffs_epfile_io.isra.17+0x444/0x590 [usb_f_fs] [ 100.868424] ? _raw_spin_unlock_irqrestore+0x27/0x40 [ 100.868457] ? kiocb_set_cancel_fn+0x57/0x60 [ 100.868477] ? ffs_ep0_poll+0xc0/0xc0 [usb_f_fs] [ 100.868512] ffs_epfile_read_iter+0xfe/0x157 [usb_f_fs] [ 100.868551] ? security_file_permission+0x9c/0xd0 [ 100.868587] ? rw_verify_area+0xac/0x120 [ 100.868633] aio_read+0x9d/0x100 [ 100.868692] ? __fget+0xa2/0xd0 [ 100.868727] ? __might_sleep+0x68/0x70 [ 100.868763] SyS_io_submit+0x471/0x680 [ 100.868878] do_int80_syscall_32+0x4e/0xd0 [ 100.868921] entry_INT80_32+0x2a/0x2a [ 100.868932] EIP: 0xb7fbb676 [ 100.868941] EFLAGS: 00000292 CPU: 1 [ 100.868951] EAX: ffffffda EBX: b7aa2000 ECX: 00000002 EDX: b7af8368 [ 100.868961] ESI: b7fbb660 EDI: b7aab000 EBP: bfb6c658 ESP: bfb6c638 [ 100.868973] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 007b Signed-off-by: Vincent Pelletier <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2017-11-27ARM: avoid faulting on qemuRussell King1-2/+2
When qemu starts a kernel in a bare environment, the default SCR has the AW and FW bits clear, which means that the kernel can't modify the PSR A or PSR F bits, and means that FIQs and imprecise aborts are always masked. When running uboot under qemu, the AW and FW SCR bits are set, and the kernel functions normally - and this is how real hardware behaves. Fix this for qemu by ignoring the FIQ bit. Fixes: 8bafae202c82 ("ARM: BUG if jumping to usermode address in kernel mode") Signed-off-by: Russell King <[email protected]>
2017-11-27mac80211: tear down RX aggregations firstSara Sharon1-1/+3
When doing HW restart we tear down aggregations. Since at this point we are not TX'ing any aggregation, while the peer is still sending RX aggregation over the air, it will make sense to tear down the RX aggregations first. Signed-off-by: Sara Sharon <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
2017-11-27mac80211: fix the update of path metric for RANN frameChun-Yeow Yeoh1-6/+9
The previous path metric update from RANN frame has not considered the own link metric toward the transmitting mesh STA. Fix this. Reported-by: Michael65535 Signed-off-by: Chun-Yeow Yeoh <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
2017-11-27mac80211: use QoS NDP for AP probingJohannes Berg7-10/+42
When connected to a QoS/WMM AP, mac80211 should use a QoS NDP for probing it, instead of a regular non-QoS one, fix this. Change all the drivers to *not* allow QoS NDP for now, even though it looks like most of them should be OK with that. Signed-off-by: Johannes Berg <[email protected]>
2017-11-27Merge tag 'v4.15-rc1' into drm-misc-fixesDaniel Vetter23247-275743/+600470
Linux 4.15-rc1 Pull in the merge window to resync. Dave didn't get his -fixes pull landed in time, and now there's another rockchip fix pending, so fast-forwarding isn't possible, hence backmerge. Signed-off-by: Daniel Vetter <[email protected]>
2017-11-27drm/arm: Replace instances of drm_dev_unref with drm_dev_put.Srishti Sharma1-2/+2
Replace drm_dev_unref with drm_dev_put as it is more consistent with kernel coding style. Done using the following semantic patch by coccinelle. @r@ expression e; @@ -drm_dev_unref(); +drm_dev_put(); Signed-off-by: Srishti Sharma <[email protected]> [split into hdlcd and malidp specific patches] Signed-off-by: Liviu Dudau <[email protected]>
2017-11-27drm: Fix checkpatch issue: "WARNING: braces {} are not necessary for single ↵Vitor Massaru Iha1-2/+1
statement blocks." Signed-off-by: Vitor Massaru Iha <[email protected]> Signed-off-by: Liviu Dudau <[email protected]>
2017-11-27USB: serial: option: add Quectel BG96 idSebastian Sjoholm1-0/+3
Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel development board (EVB). The USB id is added to option.c to allow DIAG,GPS,AT and modem communication with the BG96. Signed-off-by: Sebastian Sjoholm <[email protected]> Cc: stable <[email protected]> Signed-off-by: Johan Hovold <[email protected]>
2017-11-27drm/rockchip: dw-mipi-dsi: fix possible un-balanced runtime PM enableMirza Krak1-2/+1
In the case where the bind gets deferred we would end up with a un-balanced runtime PM enable call. Fix this by simply moving the pm_runtime_enable call to the end of the bind function when all paths have succeeded. Signed-off-by: Mirza Krak <[email protected]> Signed-off-by: Sandy Huang <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2017-11-26hwmon: Drop reference to Jean's treeJean Delvare1-1/+0
This tree has not been used for over a year, Guenter is taking all the hwmon patches in practice. Signed-off-by: Jean Delvare <[email protected]> Cc: Guenter Roeck <[email protected]> Signed-off-by: Guenter Roeck <[email protected]>
2017-11-26Linux 4.15-rc1Linus Torvalds1-2/+2
2017-11-26openvswitch: fix the incorrect flow action alloc sizezhangliping1-8/+8
If we want to add a datapath flow, which has more than 500 vxlan outputs' action, we will get the following error reports: openvswitch: netlink: Flow action size 32832 bytes exceeds max openvswitch: netlink: Flow action size 32832 bytes exceeds max openvswitch: netlink: Actions may not be safe on all matching packets ... ... It seems that we can simply enlarge the MAX_ACTIONS_BUFSIZE to fix it, but this is not the root cause. For example, for a vxlan output action, we need about 60 bytes for the nlattr, but after it is converted to the flow action, it only occupies 24 bytes. This means that we can still support more than 1000 vxlan output actions for a single datapath flow under the the current 32k max limitation. So even if the nla_len(attr) is larger than MAX_ACTIONS_BUFSIZE, we shouldn't report EINVAL and keep it move on, as the judgement can be done by the reserve_sfa_size. Signed-off-by: zhangliping <[email protected]> Acked-by: Pravin B Shelar <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-11-26Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-armLinus Torvalds6-6/+42
Pull ARM fixes from Russell King: - LPAE fixes for kernel-readonly regions - Fix for get_user_pages_fast on LPAE systems - avoid tying decompressor to a particular platform if DEBUG_LL is enabled - BUG if we attempt to return to userspace but the to-be-restored PSR value keeps us in privileged mode (defeating an issue that ftracetest found) * 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm: ARM: BUG if jumping to usermode address in kernel mode ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE ARM: 8721/1: mm: dump: check hardware RO bit for LPAE ARM: make decompressor debug output user selectable ARM: fix get_user_pages_fast
2017-11-26Merge branch 'irq-urgent-for-linus' of ↵Linus Torvalds12-15/+52
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq fixes from Thomas Glexiner: - unbreak the irq trigger type check for legacy platforms - a handful fixes for ARM GIC v3/4 interrupt controllers - a few trivial fixes all over the place * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq/matrix: Make - vs ?: Precedence explicit irqchip/imgpdc: Use resource_size function on resource object irqchip/qcom: Fix u32 comparison with value less than zero irqchip/exiu: Fix return value check in exiu_init() irqchip/gic-v3-its: Remove artificial dependency on PCI irqchip/gic-v4: Add forward definition of struct irq_domain_ops irqchip/gic-v3: pr_err() strings should end with newlines irqchip/s3c24xx: pr_err() strings should end with newlines irqchip/gic-v3: Fix ppi-partitions lookup irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails genirq: Track whether the trigger type has been set
2017-11-26Merge branch 'x86-urgent-for-linus' of ↵Linus Torvalds38-616/+472
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull misc x86 fixes from Ingo Molnar: - topology enumeration fixes - KASAN fix - two entry fixes (not yet the big series related to KASLR) - remove obsolete code - instruction decoder fix - better /dev/mem sanity checks, hopefully working better this time - pkeys fixes - two ACPI fixes - 5-level paging related fixes - UMIP fixes that should make application visible faults more debuggable - boot fix for weird virtualization environment * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits) x86/decoder: Add new TEST instruction pattern x86/PCI: Remove unused HyperTransport interrupt support x86/umip: Fix insn_get_code_seg_params()'s return value x86/boot/KASLR: Remove unused variable x86/entry/64: Add missing irqflags tracing to native_load_gs_index() x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing x86/pkeys/selftests: Fix protection keys write() warning x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey' x86/mpx/selftests: Fix up weird arrays x86/pkeys: Update documentation about availability x86/umip: Print a warning into the syslog if UMIP-protected instructions are used x86/smpboot: Fix __max_logical_packages estimate x86/topology: Avoid wasting 128k for package id array perf/x86/intel/uncore: Cache logical pkg id in uncore driver x86/acpi: Reduce code duplication in mp_override_legacy_irq() x86/acpi: Handle SCI interrupts above legacy space gracefully x86/boot: Fix boot failure when SMP MP-table is based at 0 x86/mm: Limit mmap() of /dev/mem to valid physical addresses x86/selftests: Add test for mapping placement for 5-level paging ...
2017-11-26Merge branch 'sched-urgent-for-linus' of ↵Linus Torvalds3-10/+17
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull scheduler fixes from Ingo Molnar: "Misc fixes: a documentation fix, a Sparse warning fix and a debugging fix" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/debug: Fix task state recording/printout sched/deadline: Don't use dubious signed bitfields sched/deadline: Fix the description of runtime accounting in the documentation
2017-11-26Merge branch 'perf-urgent-for-linus' of ↵Linus Torvalds3-12/+32
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull perf fixes from Ingo Molnar: "Misc fixes: two PMU driver fixes and a memory leak fix" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/core: Fix memory leak triggered by perf --namespace perf/x86/intel/uncore: Add event constraint for BDX PCU perf/x86/intel: Hide TSX events when RTM is not supported
2017-11-26Merge branch 'locking-urgent-for-linus' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull static key fix from Ingo Molnar: "Fix a boot warning related to bad init ordering of the static keys self-test" * 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: jump_label: Invoke jump_label_test() via early_initcall()
2017-11-26Merge branch 'core-urgent-for-linus' of ↵Linus Torvalds15-40/+72
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull objtool fixes from Ingo Molnar: "A handful of objtool fixes, most of them related to making the UAPI header-syncing warnings easier to read and easier to act upon" * 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: tools/headers: Sync objtool UAPI header objtool: Fix cross-build objtool: Move kernel headers/code sync check to a script objtool: Move synced files to their original relative locations objtool: Make unreachable annotation inline asms explicitly volatile objtool: Add a comment for the unreachable annotation macros
2017-11-27net: openvswitch: datapath: fix data type in queue_gso_packetsGustavo A. R. Silva1-1/+1
gso_type is being used in binary AND operations together with SKB_GSO_UDP. The issue is that variable gso_type is of type unsigned short and SKB_GSO_UDP expands to more than 16 bits: SKB_GSO_UDP = 1 << 16 this makes any binary AND operation between gso_type and SKB_GSO_UDP to be always zero, hence making some code unreachable and likely causing undesired behavior. Fix this by changing the data type of variable gso_type to unsigned int. Addresses-Coverity-ID: 1462223 Fixes: 0c19f846d582 ("net: accept UFO datagrams from tuntap and packet") Signed-off-by: Gustavo A. R. Silva <[email protected]> Acked-by: Willem de Bruijn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-11-26ARM: BUG if jumping to usermode address in kernel modeRussell King2-0/+24
Detect if we are returning to usermode via the normal kernel exit paths but the saved PSR value indicates that we are in kernel mode. This could occur due to corrupted stack state, which has been observed with "ftracetest". This ensures that we catch the problem case before we get to user code. Signed-off-by: Russell King <[email protected]>
2017-11-26nvme-rdma: Use mr poolIsrael Rukshin1-58/+37
Currently, blk_mq_tagset_iter() iterate over initial hctx tags only. If an I/O scheduler is used, it doesn't iterate the hctx scheduler tags and the static request aren't been updated. For example, while using NVMe over Fabrics RDMA host, this cause us not to reinit the scheduler requests and thus not re-register all the memory regions during the tagset re-initialization in the reconnect flow. This may lead to a memory registration error: "MEMREG for CQE 0xffff88044c14dce8 failed with status memory management operation error (6)" With this commit we don't need to reinit the requests, and thus fix this failure. Signed-off-by: Israel Rukshin <[email protected]> Reviewed-by: Sagi Grimberg <[email protected]> Reviewed-by: Max Gurtovoy <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
2017-11-26nvme-rdma: Check remotely invalidated rkey matches our expected rkeySagi Grimberg1-2/+7
If we got a remote invalidation on a bogus rkey, this is a protocol error. Fail the connection in this case. Signed-off-by: Sagi Grimberg <[email protected]> Reviewed-by: Max Gurtovoy <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
2017-11-26nvme-rdma: wait for local invalidation before completing a requestSagi Grimberg1-15/+24
We must not complete a request before the host memory region is invalidated. Luckily we have send with invalidate protocol support so we usually don't need to execute it, but in case the target did not invalidate a memory region for us, we must wait for the invalidation to complete before unmapping host memory and completing the I/O. Signed-off-by: Sagi Grimberg <[email protected]> Reviewed-by: Max Gurtovoy <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
2017-11-26nvme-rdma: don't complete requests before a send work request has completedSagi Grimberg1-4/+24
In order to guarantee that the HCA will never get an access violation (either from invalidated rkey or from iommu) when retrying a send operation we must complete a request only when both send completion and the nvme cqe has arrived. We need to set the send/recv completions flags atomically because we might have more than a single context accessing the request concurrently (one is cq irq-poll context and the other is user-polling used in IOCB_HIPRI). Only then we are safe to invalidate the rkey (if needed), unmap the host buffers, and complete the IO. Signed-off-by: Sagi Grimberg <[email protected]> Reviewed-by: Max Gurtovoy <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.