| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
A few regression fixes, the runpm ones dating back to 3.15. Also a fairly severe TMDS regression that effected a lot of GF8/9/GT2xx users.
* 'linux-3.17' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: make sure display hardware is reinitialised on runtime resume
drm/nouveau: punt fbcon resume out to a workqueue
drm/nouveau: fix regression on original nv50 board
drm/nv50/disp: fix dpms regression on certain boards
|
|
Pull networking fixes from David Miller:
1) Don't halt the firmware in r8152 driver, from Hayes Wang.
2) Handle full sized 802.1ad frames in bnx2 and tg3 drivers properly,
from Vlad Yasevich.
3) Don't sleep while holding tx_clean_lock in netxen driver, fix from
Manish Chopra.
4) Certain kinds of ipv6 routes can end up endlessly failing the route
validation test, causing it to be re-looked up over and over again.
This particularly kills input route caching in TCP sockets. Fix
from Hannes Frederic Sowa.
5) netvsc_start_xmit() has a use-after-free access to skb->len, fix
from K Y Srinivasan.
6) Fix matching of inverted containers in ematch module, from Ignacy
Gawędzki.
7) Aggregation of GRO frames via SKB ->frag_list for linear skbs isn't
handled properly, regression fix from Eric Dumazet.
8) Don't test return value of ipv4_neigh_lookup(), which returns an
error pointer, against NULL. From WANG Cong.
9) Fix an old regression where we mistakenly allow a double add of the
same tunnel. Fixes from Steffen Klassert.
10) macvtap device delete and open can run in parallel and corrupt lists
etc., fix from Vlad Yasevich.
11) Fix build error with IPV6=m NETFILTER_XT_TARGET_TPROXY=y, from Pablo
Neira Ayuso.
12) rhashtable_destroy() triggers lockdep splats, fix also from Pablo.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
bna: Update Maintainer Email
r8152: disable power cut for RTL8153
r8152: remove clearing bp
bnx2: Correctly receive full sized 802.1ad fragmes
tg3: Allow for recieve of full-size 8021AD frames
r8152: fix setting RTL8152_UNPLUG
netxen: Fix bug in Tx completion path.
netxen: Fix BUG "sleeping function called from invalid context"
ipv6: remove rt6i_genid
hyperv: Fix a bug in netvsc_start_xmit()
net: stmmac: fix stmmac_pci_probe failed when CONFIG_HAVE_CLK is selected
ematch: Fix matching of inverted containers.
gro: fix aggregation for skb using frag_list
neigh: check error pointer instead of NULL for ipv4_neigh_lookup()
ip6_gre: Return an error when adding an existing tunnel.
ip6_vti: Return an error when adding an existing tunnel.
ip6_tunnel: Return an error when adding an existing tunnel.
ip6gre: add a rtnl link alias for ip6gretap
net/mlx4_core: Allow not to specify probe_vf in SRIOV IB mode
r8152: fix the carrier off when autoresuming
...
|
|
It has come to my attention (thanks Martin) that 'discard_zeroes_data'
is only a hint. Some devices in some cases don't do what it
says on the label.
The use of DISCARD in RAID5 depends on reads from discarded regions
being predictably zero. If a write to a previously discarded region
performs a read-modify-write cycle it assumes that the parity block
was consistent with the data blocks. If all were zero, this would
be the case. If some are and some aren't this would not be the case.
This could lead to data corruption after a device failure when
data needs to be reconstructed from the parity.
As we cannot trust 'discard_zeroes_data', ignore it by default
and so disallow DISCARD on all raid4/5/6 arrays.
As many devices are trustworthy, and as there are benefits to using
DISCARD, add a module parameter to over-ride this caution and cause
DISCARD to work if discard_zeroes_data is set.
If a site want to enable DISCARD on some arrays but not on others they
should select DISCARD support at the filesystem level, and set the
raid456 module parameter.
raid456.devices_handle_discard_safely=Y
As this is a data-safety issue, I believe this patch is suitable for
-stable.
DISCARD support for RAID456 was added in 3.7
Cc: Shaohua Li <[email protected]>
Cc: "Martin K. Petersen" <[email protected]>
Cc: Mike Snitzer <[email protected]>
Cc: Heinz Mauelshagen <[email protected]>
Cc: [email protected] (3.7+)
Acked-by: Martin K. Petersen <[email protected]>
Acked-by: Mike Snitzer <[email protected]>
Fixes: 620125f2bf8ff0c4969b79653b54d7bcc9d40637
Signed-off-by: NeilBrown <[email protected]>
|
|
Linus commit 05c63c2ff23a80b654d6c088ac3ba21628db0173 modified the
runtime suspend/resume paths to skip over display-related tasks to
avoid locking issues on resume.
Unfortunately, this resulted in the display hardware being left in
a partially initialised state, preventing subsequent modesets from
completing.
This commit unifies the (many) suspend/resume paths, bringing back
display (and fbcon) handling in the runtime paths.
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Preparation for some runtime pm fixes. Currently we skip over fbcon
suspend/resume in the runtime path, which causes issues on resume if
fbcon tries to write to the framebuffer before the BAR subdev has
been resumed to restore the BAR1 VM setup.
As we might be woken up via a sysfs connector, we are unable to call
fb_set_suspend() in the resume path as it could make its way down to
a modeset and cause all sorts of locking hilarity.
To solve this, we'll just delay the fbcon resume to a workqueue.
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Xorg (and any non-DRM client really) doesn't have permission to directly
touch VRAM on nv50 and up, which the fence code prior to g84 depends on.
It's less invasive to temporarily grant it premission to do so, as it
previously did, than it is to rework fencenv50 to use the VM. That
will come later on.
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Reported in fdo#82527 comment #2.
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Update the maintainer email for BNA driver.
Signed-off-by: Rasesh Mody <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Hayes Wang says:
====================
r8152: patches about firmware
The patches fix the issues when the firmware exists.
For the multiple OS, the firmware may be loaded by the
driver of the other OS. And the Linux driver has influences
on it.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The firmware would be clear when the power cut is enabled for
RTL8153.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The xxx_clear_bp() is used to halt the firmware. It only necessary
for updating the new firmware. Besides, depend on the version of
the current firmware, it may have problem to halt the firmware
directly. Finally, halt the firmware would let the firmware code
useless, and the bugs which are fixed by the firmware would occur.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This driver, similar to tg3, has a check that will
cause full sized 802.1ad frames to be dropped. The
frame will be larger then the standard mtu due to the
presense of vlan header that has not been stripped.
The driver should not drop this frame and should process
it just like it does for 802.1q.
CC: Sony Chacko <[email protected]>
CC: [email protected]
Signed-off-by: Vladislav Yasevich <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <[email protected]>
CC: Prashant Sreedharan <[email protected]>
CC: Michael Chan <[email protected]>
Signed-off-by: Vladislav Yasevich <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Pull nfsd bugfix from Bruce Fields:
"This fixes a data corruption bug introduced by the v3.16 xdr encoding
rewrite. I haven't managed to reproduce it myself yet, but it's
apparently not hard to hit given the right workload"
* 'for-3.17' of git://linux-nfs.org/~bfields/linux:
nfsd4: fix corruption of NFSv4 read data
|
|
Fix the serial console on machines where the serial port is located on
the SuperIO chip.
Signed-off-by: Helge Deller <[email protected]>
Cc: Peter Hurley <[email protected]>
|
|
cxgbi_inet6addr_handler() can be called in interrupt context, so use rcu
protected list while finding netdev. This is observed as a scheduling in
atomic oops when running over ipv6.
Fixes: fc8d0590d914 ("libcxgbi: Add ipv6 api to driver")
Fixes: 759a0cc5a3e1 ("cxgb4i: Add ipv6 code to driver, call into libcxgbi ipv6 api")
Signed-off-by: Anish Bhatt <[email protected]>
Signed-off-by: Karen Xie <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
Signed-off-by: James Bottomley <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fix SSM2602 device identification
Another fix for v3.17, fixing device identification after the split out
of the I2C and SPI code.
|
|
Pull ARM fixes from Russell King:
"Some further ARM fixes:
- another build fix for the kprobes test code
- a fix for no kuser helpers for the set_tls code, which oopsed on
noMMU hardware
- a fix for alignment handler with neon opcodes being misinterpreted
- turning off the hardware access support, which is not implemented
- a build fix for the v7 coherency exiting code, which can be built
in non-v7 environments (but still only executed on v7 CPUs)"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8179/1: kprobes-test: Fix compile error "bad immediate value for offset"
ARM: 8178/1: fix set_tls for !CONFIG_KUSER_HELPERS
ARM: 8177/1: cacheflush: Fix v7_exit_coherency_flush exynos build breakage on ARMv6
ARM: 8165/1: alignment: don't break misaligned NEON load/store
ARM: 8164/1: mm: clear SCTLR.HA instead of setting it for LPAE
|
|
The flag of RTL8152_UNPLUG should only be set when the device is
unplugged, not each time the rtl8152_disconnect() is called.
Otherwise, the device wouldn't be stopped normally.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Manish Chopra says:
====================
netxen: Bug fixes.
This series fixes some TX specific issues.
* Move spin_lock(tx_clean_lock) in down path to fix
atomic sleep bug (Reported by Mike Galbraith).
* Fix hang in interface down while running traffic.
Please consider applying this to 'net'.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
o Driver is not updating sw_consumer while processing Tx completion
when interface is going down. Due to this interface down path gets
stuck forever waiting for NAPI to complete.
Signed-off-by: Manish Chopra <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
o __netxen_nic_down() function might sleep while holding spinlock_t(tx_clean_lock).
Acquire this lock for only releasing TX buffers instead of taking it
for whole down path.
Reported-by: Mike Galbraith <[email protected]>
Signed-off-by: Manish Chopra <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The calculation of page_ptr here is wrong in the case the read doesn't
start at an offset that is a multiple of a page.
The result is that nfs4svc_encode_compoundres sets rq_next_page to a
value one too small, and then the loop in svc_free_res_pages may
incorrectly fail to clear a page pointer in rq_respages[].
Pages left in rq_respages[] are available for the next rpc request to
use, so xdr data may be written to that page, which may hold data still
waiting to be transmitted to the client or data in the page cache.
The observed result was silent data corruption seen on an NFSv4 client.
We tag this as "fixing" 05638dc73af2 because that commit exposed this
bug, though the incorrect calculation predates it.
Particular thanks to Andrea Arcangeli and David Gilbert for analysis and
testing.
Fixes: 05638dc73af2 "nfsd4: simplify server xdr->next_page use"
Cc: [email protected]
Reported-by: Andrea Arcangeli <[email protected]>
Tested-by: "Dr. David Alan Gilbert" <[email protected]>
Signed-off-by: J. Bruce Fields <[email protected]>
|
|
The existing implementation of swsusp_free iterates over all
pfns in the system and checks every bit in the two memory
bitmaps.
This doesn't scale very well with large numbers of pfns,
especially when the bitmaps are not populated very densly.
Change the algorithm to iterate over the set bits in the
bitmaps instead to make it scale better in large memory
configurations.
Also add a memory_bm_clear_current() helper function that
clears the bit for the last position returned from the
memory bitmap.
This new version adds a !NULL check for the memory bitmaps
before they are walked. Not doing so causes a kernel crash
when the bitmaps are NULL.
Signed-off-by: Joerg Roedel <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
'cpu_data' is updated for policy->cpu first and then for all CPUs in
policy->cpus. policy->cpus is guaranteed to contain policy->cpu as well and so
the first write to 'cpu_data' for policy->cpu is redundant. Remove it.
Acked-by: Tang Yuantian <[email protected]>
Signed-off-by: Viresh Kumar <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
The ACPI GPE wakeup from suspend-to-idle is currently based on using
the IRQF_NO_SUSPEND flag for the ACPI SCI, but that is problematic
for a couple of reasons. First, in principle the ACPI SCI may be
shared and IRQF_NO_SUSPEND does not really work well with shared
interrupts. Second, it may require the ACPI subsystem to special-case
the handling of device notifications depending on whether or not
they are received during suspend-to-idle in some places which would
lead to fragile code. Finally, it's better the handle ACPI wakeup
interrupts consistently with wakeup interrupts from other sources.
For this reason, remove the IRQF_NO_SUSPEND flag from the ACPI SCI
and use enable_irq_wake()/disable_irq_wake() with it instead, which
requires two additional platform hooks to be added to struct
platform_freeze_ops.
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Rename several local functions related to platform handling during
system suspend resume in suspend.c so that their names better
reflect their roles.
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Subsequent change sets will add platform-related operations between
dpm_suspend_late() and dpm_suspend_noirq() as well as between
dpm_resume_noirq() and dpm_resume_early() in suspend_enter(), so
export these functions for suspend_enter() to be able to call them
separately and split the invocations of dpm_suspend_end() and
dpm_resume_start() in there accordingly.
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
|
|
Add a routine for host OSes to enable all wakeup GPEs and disable
all of the non-wakeup ones at the same time.
It will be used for the handling of GPE wakeup from suspend-to-idle
in Linux.
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Since acpi_hw_enable_wakeup_gpe_block() is currently always called
after disabling all GPEs, it can actually write zeros to all
non-wakeup enable bits unconditionally.
That will be useful going forward for disabling runtime GPEs and
enabling wakeup GPEs in one go instead of doing that in two steps
(disable runtime and enable wakeup) which in theory may lead to a
loss of a wakeup event.
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Commit 8e30444e1530 ("cpufreq: fix cpufreq suspend/resume for intel_pstate")
introduced a bug where the governors wouldn't be stopped anymore for
->target{_index}() drivers during suspend. This happens because
'cpufreq_suspended' is updated before stopping the governors during suspend
and due to this __cpufreq_governor() would return early due to this check:
/* Don't start any governor operations if we are entering suspend */
if (cpufreq_suspended)
return 0;
Fixes: 8e30444e1530 ("cpufreq: fix cpufreq suspend/resume for intel_pstate")
Cc: 3.15+ <[email protected]> # 3.15+: 8e30444e1530 "cpufreq: fix cpufreq suspend/resume for intel_pstate"
Signed-off-by: Viresh Kumar <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
The _DOD method lists which video output device is currently attached so
we should only care about them and ignore others. An user recently
reported that there are two acpi_video interfaces appeared on his system
and one of them doesn't work. From the acpidump, it is found that there
are more than one video output devices that have _BCM control method but
the _DOD lists only one of them. So this patch checks if the video output
device is in the _DOD list and will not create backlight device if it is
not in the list. Also, we consider the broken _DOD case(reflected by the
video->attached_count is 0) and do not change behaviour for those broken
_DOD systems.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84111
Reported-and-tested-by: [email protected]
Signed-off-by: Aaron Lu <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
|
|
Eric Dumazet noticed that all no-nonexthop or no-gateway routes which
are already marked DST_HOST (e.g. input routes routes) will always be
invalidated during sk_dst_check. Thus per-socket dst caching absolutely
had no effect and early demuxing had no effect.
Thus this patch removes rt6i_genid: fn_sernum already gets modified during
add operations, so we only must ensure we mutate fn_sernum during ipv6
address remove operations. This is a fairly cost extensive operations,
but address removal should not happen that often. Also our mtu update
functions do the same and we heard no complains so far. xfrm policy
changes also cause a call into fib6_flush_trees. Also plug a hole in
rt6_info (no cacheline changes).
I verified via tracing that this change has effect.
Cc: Eric Dumazet <[email protected]>
Cc: YOSHIFUJI Hideaki <[email protected]>
Cc: Vlad Yasevich <[email protected]>
Cc: Nicolas Dichtel <[email protected]>
Cc: Martin Lau <[email protected]>
Signed-off-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When compiling kprobes-test-arm.c the following error has been observed
/tmp/ccoT403o.s:21439: Error: bad immediate value for offset (4168)
This is caused by the compiler spilling it's literal pool too far away
from the site which is trying to reference it with a PC relative load.
This arises because the compiler is underestimating the size of the
inline assembler code present, which apparently it approximates as 4
bytes per line or instruction.
We fix this problem by moving the operations which generate more than
4 bytes out of the text section. Specifically, moving the .ascii
directives to the .rodata section.
Signed-off-by: Jon Medhurst <[email protected]>
Signed-off-by: Russell King <[email protected]>
|
|
Joachim Eastwood reports that commit fbfb872f5f41 "ARM: 8148/1: flush
TLS and thumbee register state during exec" causes a boot-time crash
on a Cortex-M4 nommu system:
Freeing unused kernel memory: 68K (281e5000 - 281f6000)
Unhandled exception: IPSR = 00000005 LR = fffffff1
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-rc6-00313-gd2205fa30aa7 #191
task: 29834000 ti: 29832000 task.ti: 29832000
PC is at flush_thread+0x2e/0x40
LR is at flush_thread+0x21/0x40
pc : [<2800954a>] lr : [<2800953d>] psr: 4100000b
sp : 29833d60 ip : 00000000 fp : 00000001
r10: 00003cf8 r9 : 29b1f000 r8 : 00000000
r7 : 29b0bc00 r6 : 29834000 r5 : 29832000 r4 : 29832000
r3 : ffff0ff0 r2 : 29832000 r1 : 00000000 r0 : 282121f0
xPSR: 4100000b
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-rc6-00313-gd2205fa30aa7 #191
[<2800afa5>] (unwind_backtrace) from [<2800a327>] (show_stack+0xb/0xc)
[<2800a327>] (show_stack) from [<2800a963>] (__invalid_entry+0x4b/0x4c)
The problem is that set_tls is attempting to clear the TLS location in
the kernel-user helper page, which isn't set up on V7M.
Fix this by guarding the write to the kuser helper page with
a CONFIG_KUSER_HELPERS ifdef.
Fixes: fbfb872f5f41 ARM: 8148/1: flush TLS and thumbee register state during exec
Reported-by: Joachim Eastwood <[email protected]>
Tested-by: Joachim Eastwood <[email protected]>
Cc: [email protected]
Signed-off-by: Nathan Lynch <[email protected]>
Signed-off-by: Russell King <[email protected]>
|
|
on ARMv6
This fixes build breakage of platsmp.c if ARMv6 was chosen for compile
time options (e.g. by building allmodconfig):
$ make allmodconfig
$ make
CC arch/arm/mach-exynos/platsmp.o
/tmp/ccdQM0Eg.s: Assembler messages:
/tmp/ccdQM0Eg.s:432: Error: selected processor does not support ARM mode `isb '
/tmp/ccdQM0Eg.s:437: Error: selected processor does not support ARM mode `isb '
/tmp/ccdQM0Eg.s:438: Error: selected processor does not support ARM mode `dsb '
make[1]: *** [arch/arm/mach-exynos/platsmp.o] Error 1
The error was introduced in commit "ARM: EXYNOS: Move code from
hotplug.c to platsmp.c". Previously code using
v7_exit_coherency_flush() macro was built with '-march=armv7-a' flag but
this flag dissapeared during the movement.
Fix this by annotating the v7_exit_coherency_flush() asm code with
armv7-a architecture.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reported-by: Mark Brown <[email protected]>
Acked-by: Nicolas Pitre <[email protected]>
Signed-off-by: Kukjin Kim <[email protected]>
Signed-off-by: Russell King <[email protected]>
|
|
The correct type (SSM2602/SSM2603/SSM2604) is passed down
from the ssm2602_spi_probe()/ssm2602_spi_probe() functions,
so use that instead of hardcoding it to SSM2602 in
ssm2602_probe().
Fixes: c924dc68f737 ("ASoC: ssm2602: Split SPI and I2C code into different modules")
Signed-off-by: Stefan Kristiansson <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Acked-by: Lars-Peter Clausen <[email protected]>
Cc: [email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.17
A few small driver specific fixes and a couple of error handling fixes
in the core.
|
|
After the packet is successfully sent, we should not touch the skb
as it may have been freed. This patch is based on the work done by
Long Li <[email protected]>.
In this version of the patch I have fixed issues pointed out by David.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <[email protected]>
Tested-by: Long Li <[email protected]>
Tested-by: Sitsofe Wheeler <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The commit 46420dd73b80 (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.
Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.
Fixes: 46420dd73b80 (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <[email protected]>
Acked-by: Geert Uytterhoeven <[email protected]>
Acked-by: Wolfram Sang <[email protected]>
Acked-by: Mark Brown <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Some of the Thinkpads' firmware will issue a backlight change request
through i915 operation region unconditionally on AC plug/unplug, the
backlight level used is arbitrary and thus should be ignored. This is
handled by commit 0b9f7d93ca61 (ACPI / i915: ignore firmware requests
for backlight change). Then there is a Dell laptop whose vendor backlight
interface also makes use of operation region to change backlight level
and with the above commit, that interface no long works. The condition
used to ignore the backlight change request from firmware is thus
changed to: if the vendor backlight interface is not in use and the ACPI
backlight interface is broken, we ignore the requests; oterwise, we keep
processing them.
Fixes: 0b9f7d93ca61 (ACPI / i915: ignore firmware requests for backlight change)
Link: https://lkml.org/lkml/2014/9/23/854
Reported-and-tested-by: Pali Rohár <[email protected]>
Cc: 3.16+ <[email protected]> # 3.16+
Signed-off-by: Aaron Lu <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
When the CONFIG_HAVE_CLK is selected for the system, the stmmac_pci_probe
will fail with dmesg:
[ 2.167225] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002)
[ 2.178267] stmmaceth 0000:00:14.6: enabling bus mastering
[ 2.178436] stmmaceth 0000:00:14.6: irq 24 for MSI/MSI-X
[ 2.178703] stmmaceth 0000:00:14.6: stmmac_dvr_probe: warning: cannot
get CSR clock
[ 2.186503] stmmac_pci_probe: main driver probe failed
[ 2.194003] stmmaceth 0000:00:14.6: disabling bus mastering
[ 2.196473] stmmaceth: probe of 0000:00:14.6 failed with error -2
This patch fix the issue by breaking the dependency to devm_clk_get()
as the CSR clock can be obtained at priv->plat->clk_csr from pci driver.
Reported-by: Tobias Klausmann <[email protected]>
Signed-off-by: Kweh, Hock Leong <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Negated expressions and sub-expressions need to have their flags checked for
TCF_EM_INVERT and their result negated accordingly.
Signed-off-by: Ignacy Gawędzki <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In commit 8a29111c7ca6 ("net: gro: allow to build full sized skb")
I added a regression for linear skb that traditionally force GRO
to use the frag_list fallback.
Erez Shitrit found that at most two segments were aggregated and
the "if (skb_gro_len(p) != pinfo->gso_size)" test was failing.
This is because pinfo at this spot still points to the last skb in the
chain, instead of the first one, where we find the correct gso_size
information.
Signed-off-by: Eric Dumazet <[email protected]>
Fixes: 8a29111c7ca6 ("net: gro: allow to build full sized skb")
Reported-by: Erez Shitrit <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics
and a slightly buggy strncasecmp. The latter is the POSIX name, so
strnicmp was renamed to strncasecmp, and strnicmp made into a wrapper
for the new strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in
the future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
This patch ensures the cpus to kexec/reboot at nominal frequency.
Nominal frequency is the highest cpu frequency on PowerPC at
which the cores can run without getting throttled.
If the host kernel had set the cpus to a low pstate and then it
kexecs/reboots to a cpufreq disabled kernel it would cause the target
kernel to perform poorly. It will also increase the boot up time of
the target kernel. So set the cpus to high pstate, in this case to
nominal frequency before rebooting to avoid such scenarios.
The reboot notifier will set the cpus to nominal frequncy.
Signed-off-by: Shilpasri G Bhat <[email protected]>
Reviewed-by: Preeti U Murthy <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
policy->cpus to minimum
Its possible today that the pstate of a core is held at a high even after the
entire core is hotplugged out if a load had just run on the hotplugged cpu. This is
fair, since it is assumed that the pstate does not matter to a cpu in a deep idle
state, which is the expected state of a hotplugged core on powerpc. However on powerpc,
the pstate at a socket level is held at the maximum of the pstates of each core. Even
if the pstates of the active cores on that socket is low, the socket pstate is held
high due to the pstate of the hotplugged core in the above mentioned scenario. This
can cost significant amount of power loss for no good.
Besides, since it is a non active core, nothing can be done from the kernel's end
to set the frequency of the core right. Hence make use of the stop_cpu callback
to explicitly set the pstate of the core to a minimum when the last cpu of the
core gets hotplugged out.
Signed-off-by: Preeti U Murthy <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Commit 367dc4aa932bfb3 ("cpufreq: Add stop CPU callback to
cpufreq_driver interface") introduced the stop CPU callback for
intel_pstate drivers. During the CPU_DOWN_PREPARE stage, this
callback is invoked so that drivers can take some action on the
pstate of the cpu before it is taken offline. This callback was
assumed to be useful only for those drivers which have implemented
the set_policy CPU callback because they have no other way to take
action about the cpufreq of a CPU which is being hotplugged out
except in the exit callback which is called very late in the offline
process.
The drivers which implement the target/target_index callbacks were
expected to take care of requirements like the ones that commit
367dc4aa addresses in the GOV_STOP notification event. But there
are disadvantages to restricting the usage of stop CPU callback
to cpufreq drivers that implement the set_policy callbacks and who
want to take explicit action on the setting the cpufreq during a
hotplug operation.
1.GOV_STOP gets called for every CPU offline and drivers would usually
want to take action when the last cpu in the policy->cpus mask
is taken offline. As long as there is more than one cpu in the
policy->cpus mask, cpufreq core itself makes sure that the freq
for the other cpus in this mask is set according to the maximum load.
This is sensible and drivers which implement the target_index callback
would mostly not want to modify that. However the cpufreq core leaves a
loose end when the cpu in the policy->cpus mask is the last one to go offline;
it does nothing explicit to the frequency of the core. Drivers may need
a way to take some action here and stop CPU callback mechanism is the
best way to do it today.
2. We cannot implement driver specific actions in the GOV_STOP mechanism.
So we will need another driver callback which is invoked from here which is
unnecessary.
Therefore this patch extends the usage of stop CPU callback to be used
by all cpufreq drivers as long as they have this callback implemented
and irrespective of whether they are set_policy/target_index drivers.
The assumption is if the drivers find the GOV_STOP path to be a suitable
way of implementing what they want to do with the freq of the cpu
going offine,they will not implement the stop CPU callback at all.
Signed-off-by: Preeti U Murthy <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|