aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2022-08-25pinctrl: qcom: Add sm8450 lpass lpi pinctrl driverSrinivas Kandagatla3-0/+250
Add pinctrl driver to support pin configuration for LPASS (Low Power Audio SubSystem) LPI (Low Power Island) pinctrl on SM8450. This IP is an additional pin control block for Audio Pins on top the existing SoC Top level pin-controller. Hardware setup looks like: TLMM GPIO[165 - 187] --> LPASS LPI GPIO [0 - 22] This pin controller has some similarities compared to Top level msm SoC Pin controller like 'each pin belongs to a single group' and so on. However this one is intended to control only audio pins in particular, which can not be configured/touched by the Top level SoC pin controller except setting them as gpios. Apart from this, slew rate is also available in this block for certain pins which are connected to SLIMbus or SoundWire Bus. Signed-off-by: Srinivas Kandagatla <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-25dt-bindings: pinctrl: qcom: Add sm8450 lpass lpi pinctrl bindingsSrinivas Kandagatla1-0/+135
Add device tree binding Documentation details for Qualcomm SM8450 LPASS(Low Power Audio Sub System) LPI(Low Power Island) pinctrl driver. Signed-off-by: Srinivas Kandagatla <[email protected]> Reviewed-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-25pinctrl: nomadik: Convert drivers to use struct pingroup and PINCTRL_PINGROUP()Andy Shevchenko4-186/+180
The pin control header provides struct pingroup and PINCTRL_PINGROUP() macro. Utilize them instead of open coded variants in the driver. Signed-off-by: Andy Shevchenko <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-25pinctrl: bcm: Convert drivers to use struct pingroup and PINCTRL_PINGROUP()Andy Shevchenko7-320/+259
The pin control header provides struct pingroup and PINCTRL_PINGROUP() macro. Utilize them instead of open coded variants in the driver. Signed-off-by: Andy Shevchenko <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-25pinctrl: Add Cypress cy8c95x0 supportPatrick Rudolph4-0/+1402
Add support for cypress I2C GPIO expanders cy8c9520, cy8c9540 and cy8c9560. The GPIO expanders feature a PWM mode, thus add it as pinctrl driver. The chip features multiple drive modes for each pin when configured as output and multiple bias settings when configured as input. Tested all three components and verified that all functionality is fully working. Datasheet: https://www.cypress.com/file/37971/download Signed-off-by: Patrick Rudolph <[email protected]> Signed-off-by: Naresh Solanki <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-25dt-binding: pinctrl: Add cypress,cy8c95x0Patrick Rudolph1-0/+134
Added device tree binding documentation for Cypress CY8C95x0 I2C pin-controller. Signed-off-by: Patrick Rudolph <[email protected]> Reviewed-by: Krzysztof Kozlowski <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-22dt-bindings: pinctrl: aspeed: Add missing properties to examplesRob Herring3-0/+16
The aspeed pinctrl parent node (SCU) in the examples is missing various properties. Add the properties in preparation for the SCU schema. Signed-off-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-22pinctrl: armada-37xx: Remove unused macro PIN_GRP()Pali Rohár1-10/+0
Macro PIN_GRP() is not used, remove it. Signed-off-by: Pali Rohár <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-22pinctrl: armada-37xx: Checks for errors in gpio_request_enable callbackPali Rohár1-2/+6
Now when all MPP pins are properly defined and every MPP pin has GPIO function, always checks for errors in armada_37xx_gpio_request_enable() function when calling armada_37xx_pmx_set_by_name(). Function armada_37xx_pmx_set_by_name() should not return "not supported" error anymore for any GPIO pin when requesting GPIO mode. Fixes: 87466ccd9401 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx") Signed-off-by: Pali Rohár <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-22pinctrl: armada-37xx: Fix definitions for MPP pins 20-22Pali Rohár1-3/+5
All 3 MPP pins (20, 21 and 22) can be configured individually and also can be configured to GPIO functions. Fix definitions for these MPP pins in existing pin groups. After this change GPIO function can be enabled just for one of these 3 pins. Fixes: 87466ccd9401 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx") Signed-off-by: Pali Rohár <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-22pinctrl: armada-37xx: Add missing GPIO-only pinsPali Rohár1-0/+12
gpio1_5 and gpio2_2 are GPIO-only pins. Add them into MPP groups table so they are properly exported as valid pin numbers. Fixes: 87466ccd9401 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx") Signed-off-by: Pali Rohár <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-22pinctrl: rockchip: Add RV1126 pinctrl supportJagan Teki2-7/+327
RV1126 has five GPIOs groups - GPIO0 in PD_MMU and GPIO1-4 in PD_BUS. In GPIO0, up to Lower C group GPIO0_C[3:0] is part of PMU but rest of the groups from there are part of GRF. Added pinctrl support for RV1126 and the pull, drv and schmitt calculations are inferred from [1] authored by Jianqun Xu. [1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/pinctrl/pinctrl-rockchip.c Cc: [email protected] Cc: Linus Walleij <[email protected]> Signed-off-by: Jianqun Xu <[email protected]> Signed-off-by: Sugar Zhang <[email protected]> Signed-off-by: Jagan Teki <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-22dt-bindings: pinctrl: rockchip: Document RV1126 pinctrlJagan Teki1-0/+1
Document dt-bindings for RV1126 SoC pinctrl support. Cc: [email protected] Cc: Linus Walleij <[email protected]> Acked-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: Jagan Teki <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2022-08-19dt-bindings: pinctrl: samsung: deprecate header with register constantsKrzysztof Kozlowski1-0/+7
For convenience (less code duplication, some meaning added to raw number), the pin controller pin configuration register values were defined in the bindings header. These are not some IDs or other abstraction layer but raw numbers used in the registers These constants do not fit the purpose of bindings. They do not provide any abstraction, any hardware and driver independent ID. With minor exceptions, the Linux drivers actually do not use the bindings header at all. All of the constants were moved already to headers local to DTS (residing in DTS directory) and to Samsung pinctrl driver (where applicable), so remove any references to the bindings header and add a warning tha tit is deprecated. Signed-off-by: Krzysztof Kozlowski <[email protected]> Reviewed-by: Chanho Park <[email protected]> Acked-by: Rob Herring <[email protected]> Reviewed-by: Linus Walleij <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-08-19dt-bindings: pinctrl: samsung: stop using bindings header with constantsKrzysztof Kozlowski2-37/+27
The bindings header with pin controller register values is being deprecated and DTS already switched to a DTS-local header. Do not reference the bindings header in schema and replace the defines with raw values. Signed-off-by: Krzysztof Kozlowski <[email protected]> Reviewed-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-08-16i2c: Make remove callback return voidUwe Kleine-König619-1733/+646
The value returned by an i2c driver's remove function is mostly ignored. (Only an error message is printed if the value is non-zero that the error is ignored.) So change the prototype of the remove function to return no value. This way driver authors are not tempted to assume that passing an error to the upper layer is a good idea. All drivers are adapted accordingly. There is no intended change of behaviour, all callbacks were prepared to return 0 before. Reviewed-by: Peter Senna Tschudin <[email protected]> Reviewed-by: Jeremy Kerr <[email protected]> Reviewed-by: Benjamin Mugnier <[email protected]> Reviewed-by: Javier Martinez Canillas <[email protected]> Reviewed-by: Crt Mori <[email protected]> Reviewed-by: Heikki Krogerus <[email protected]> Acked-by: Greg Kroah-Hartman <[email protected]> Acked-by: Marek Behún <[email protected]> # for leds-turris-omnia Acked-by: Andy Shevchenko <[email protected]> Reviewed-by: Petr Machata <[email protected]> # for mlxsw Reviewed-by: Maximilian Luz <[email protected]> # for surface3_power Acked-by: Srinivas Pandruvada <[email protected]> # for bmc150-accel-i2c + kxcjk-1013 Reviewed-by: Hans Verkuil <[email protected]> # for media/* + staging/media/* Acked-by: Miguel Ojeda <[email protected]> # for auxdisplay/ht16k33 + auxdisplay/lcd2s Reviewed-by: Luca Ceresoli <[email protected]> # for versaclock5 Reviewed-by: Ajay Gupta <[email protected]> # for ucsi_ccg Acked-by: Jonathan Cameron <[email protected]> # for iio Acked-by: Peter Rosin <[email protected]> # for i2c-mux-*, max9860 Acked-by: Adrien Grassein <[email protected]> # for lontium-lt8912b Reviewed-by: Jean Delvare <[email protected]> # for hwmon, i2c-core and i2c/muxes Acked-by: Corey Minyard <[email protected]> # for IPMI Reviewed-by: Vladimir Oltean <[email protected]> Acked-by: Dmitry Torokhov <[email protected]> Acked-by: Sebastian Reichel <[email protected]> # for drivers/power Acked-by: Krzysztof Hałasa <[email protected]> Signed-off-by: Uwe Kleine-König <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2022-08-16gpio: pca953x: Make platform teardown callback return voidUwe Kleine-König3-17/+8
All platforms that provide a teardown callback return 0. New users are supposed to not make use of platform support, so there is no functionality lost. This patch is a preparation for making i2c remove callbacks return void. Reviewed-by: Andy Shevchenko <[email protected]> Signed-off-by: Uwe Kleine-König <[email protected]> Acked-by: Bartosz Golaszewski <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2022-08-16leds: lm3601x: Improve error reporting for problems during .remove()Uwe Kleine-König1-3/+8
Returning an error value in an i2c remove callback results in a generic error message being emitted by the i2c core, but otherwise it doesn't make a difference. The device goes away anyhow and the devm cleanups are called. So instead of triggering the generic i2c error message, emit a more helpful message if a problem occurs and return 0 to suppress the generic message. This patch is a preparation for making i2c remove callbacks return void. Acked-by: Pavel Machek <[email protected]> Signed-off-by: Uwe Kleine-König <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2022-08-16leds: lm3601x: Don't use mutex after it was destroyedUwe Kleine-König1-2/+0
The mutex might still be in use until the devm cleanup callback devm_led_classdev_flash_release() is called. This only happens some time after lm3601x_remove() completed. Fixes: e63a744871a3 ("leds: lm3601x: Convert class registration to device managed") Acked-by: Pavel Machek <[email protected]> Signed-off-by: Uwe Kleine-König <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2022-08-16leds: lm3697: Remove duplicated error reporting in .remove()Uwe Kleine-König1-3/+1
Returning an error value from an i2c remove callback results in an error message being emitted by the i2c core, but otherwise it doesn't make a difference. The device goes away anyhow and the devm cleanups are called. As lm3697_remove() already emits an error message on failure and the additional error message by the i2c core doesn't add any useful information, don't pass the error value up the stack. Instead continue to clean up and return 0. This patch is a preparation for making i2c remove callbacks return void. Acked-by: Pavel Machek <[email protected]> Signed-off-by: Uwe Kleine-König <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2022-08-16drm/i2c/sil164: Drop no-op remove functionUwe Kleine-König1-7/+0
A remove callback that just returns 0 is equivalent to no callback at all as can be seen in i2c_device_remove(). So simplify accordingly. Signed-off-by: Uwe Kleine-König <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2022-08-16pinctrl: samsung: Finish initializing the gpios before registering themSaravana Kannan1-4/+4
As soon as a gpio is registered, it should be usable by a consumer. So, do all the initialization before registering the gpios. Without this change, a consumer can request a GPIO IRQ and have the gpio to IRQ mapping fail. Signed-off-by: Saravana Kannan <[email protected]> Reviewed-by: Sam Protsenko <[email protected]> Reviewed-by: Chanho Park <[email protected]> Tested-by: Chanho Park <[email protected]> Signed-off-by: Krzysztof Kozlowski <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-08-16dt-bindings: pinctrl: renesas: Document RZ/Five SoCLad Prabhakar1-1/+1
RZ/Five SoC is pin compatible with RZ/G2UL (Type 1) SoC. This patch updates the comment to include RZ/Five SoC so that we make it clear "renesas,r9a07g043-pinctrl" compatible string will be used for RZ/Five SoC. Signed-off-by: Lad Prabhakar <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Geert Uytterhoeven <[email protected]>
2022-08-14Linux 6.0-rc1Linus Torvalds1-4/+4
2022-08-14radix-tree: replace gfp.h inclusion with gfp_types.hYury Norov1-1/+1
Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we have gfp_types.h for this. Fixes powerpc allmodconfig build: In file included from include/linux/nodemask.h:97, from include/linux/mmzone.h:17, from include/linux/gfp.h:7, from include/linux/radix-tree.h:12, from include/linux/idr.h:15, from include/linux/kernfs.h:12, from include/linux/sysfs.h:16, from include/linux/kobject.h:20, from include/linux/pci.h:35, from arch/powerpc/kernel/prom_init.c:24: include/linux/random.h: In function 'add_latent_entropy': >> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'? 25 | add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy)); | ^~~~~~~~~~~~~~ | add_latent_entropy include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in Reported-by: kernel test robot <[email protected]> CC: Andy Shevchenko <[email protected]> CC: Andrew Morton <[email protected]> CC: Jason A. Donenfeld <[email protected]> Signed-off-by: Yury Norov <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2022-08-14Merge tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds1-0/+3
Pull vfs lseek fix from Al Viro: "Fix proc_reg_llseek() breakage. Always had been possible if somebody left NULL ->proc_lseek, became a practical issue now" * tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: take care to handle NULL ->proc_lseek()
2022-08-14take care to handle NULL ->proc_lseek()Al Viro1-0/+3
Easily done now, just by clearing FMODE_LSEEK in ->f_mode during proc_reg_open() for such entries. Fixes: 868941b14441 "fs: remove no_llseek" Signed-off-by: Al Viro <[email protected]>
2022-08-14Merge tag 'for-linus-6.0-rc1b-tag' of ↵Linus Torvalds16-36/+116
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull more xen updates from Juergen Gross: - fix the handling of the "persistent grants" feature negotiation between Xen blkfront and Xen blkback drivers - a cleanup of xen.config and adding xen.config to Xen section in MAINTAINERS - support HVMOP_set_evtchn_upcall_vector, which is more compliant to "normal" interrupt handling than the global callback used up to now - further small cleanups * tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections xen: remove XEN_SCRUB_PAGES in xen.config xen/pciback: Fix comment typo xen/xenbus: fix return type in xenbus_file_read() xen-blkfront: Apply 'feature_persistent' parameter when connect xen-blkback: Apply 'feature_persistent' parameter when connect xen-blkback: fix persistent grants negotiation x86/xen: Add support for HVMOP_set_evtchn_upcall_vector
2022-08-14Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of ↵Linus Torvalds112-4871/+93678
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux Pull more perf tool updates from Arnaldo Carvalho de Melo: - 'perf c2c' now supports ARM64, adjust its output to cope with differences with what is in x86_64. Now go find false sharing on ARM64 (at least Neoverse) as well! - Refactor the JSON processing, making the output more compact and thus reducing the size of the resulting perf binary - Improvements for 'perf offcpu' profiling, including tracking child processes - Update Intel JSON metrics and events files for broadwellde, broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown, knightslanding, sapphirerapids, skylakex and snowridgex - Add 'perf stat' JSON output and a 'perf test' entry for it - Ignore memfd and anonymous mmap events if jitdump present - Refactor 'perf test' shell tests allowing subdirs - Fix an error handling path in 'parse_perf_probe_command()' - Fixes for the guest Intel PT tracing patchkit in the 1st batch of this merge window - Print debuginfod queries if -v option is used, to explain delays in processing when debuginfo servers are enabled to fetch DSOs with richer symbol tables - Improve error message for 'perf record -p not_existing_pid' - Fix openssl and libbpf feature detection - Add PMU pai_crypto event description for IBM z16 on 'perf list' - Fix typos and duplicated words on comments in various places * tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits) perf test: Refactor shell tests allowing subdirs perf vendor events: Update events for snowridgex perf vendor events: Update events and metrics for skylakex perf vendor events: Update metrics for sapphirerapids perf vendor events: Update events for knightslanding perf vendor events: Update metrics for jaketown perf vendor events: Update metrics for ivytown perf vendor events: Update events and metrics for icelakex perf vendor events: Update events and metrics for haswellx perf vendor events: Update events and metrics for cascadelakex perf vendor events: Update events and metrics for broadwellx perf vendor events: Update metrics for broadwellde perf jevents: Fold strings optimization perf jevents: Compress the pmu_events_table perf metrics: Copy entire pmu_event in find metric perf pmu-events: Hide the pmu_events perf pmu-events: Don't assume pmu_event is an array perf pmu-events: Move test events/metrics to JSON perf test: Use full metric resolution perf pmu-events: Hide pmu_events_map ...
2022-08-14Merge tag 'powerpc-6.0-2' of ↵Linus Torvalds6-30/+25
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: - Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit CPUs trap on it rather than ignoring it as they should. - Fix ftrace when building with clang, which was broken by some refactoring. - A couple of other minor fixes. Thanks to Christophe Leroy, Naveen N. Rao, Nick Desaulniers, Ondrej Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool. * tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/kexec: Fix build failure from uninitialised variable powerpc/ppc-opcode: Fix PPC_RAW_TW() powerpc64/ftrace: Fix ftrace for clang builds powerpc: Make eh value more explicit when using lwarx powerpc: Don't hide eh field of lwarx behind a macro powerpc: Fix eh field when calling lwarx on PPC32
2022-08-13Merge tag 'pull-work.misc' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull /proc/mounts fix from Al Viro: "Fix for /proc/mounts escaping - escape the '#' character too" * tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: vfs: escape hash as well
2022-08-13Merge tag '5.20-rc-smb3-client-fixes-part2' of ↵Linus Torvalds19-445/+528
git://git.samba.org/sfrench/cifs-2.6 Pull more cifs updates from Steve French: - two fixes for stable, one for a lock length miscalculation, and another fixes a lease break timeout bug - improvement to handle leases, allows the close timeout to be configured more safely - five restructuring/cleanup patches * tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: cifs: Do not access tcon->cfids->cfid directly from is_path_accessible cifs: Add constructor/destructors for tcon->cfid SMB3: fix lease break timeout when multiple deferred close handles for the same file. smb3: allow deferred close timeout to be configurable cifs: Do not use tcon->cfid directly, use the cfid we get from open_cached_dir cifs: Move cached-dir functions into a separate file cifs: Remove {cifs,nfs}_fscache_release_page() cifs: fix lock length calculation
2022-08-13afs: Enable multipage folio supportDavid Howells2-1/+3
Enable multipage folio support for the afs filesystem. Support has already been implemented in netfslib, fscache and cachefiles and in most of afs, but I've waited for Matthew Wilcox's latest folio changes. Note that it does require a change to afs_write_begin() to return the correct subpage. This is a "temporary" change as we're working on getting rid of the need for ->write_begin() and ->write_end() completely, at least as far as network filesystems are concerned - but it doesn't prevent afs from making use of the capability. Signed-off-by: David Howells <[email protected]> Acked-by: Matthew Wilcox (Oracle) <[email protected]> Tested-by: [email protected] Cc: Marc Dionne <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/lkml/[email protected]/ Signed-off-by: Linus Torvalds <[email protected]>
2022-08-13Merge tag 'timers-urgent-2022-08-13' of ↵Linus Torvalds4-4/+8
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timer fixes from Ingo Molnar: "Misc timer fixes: - fix a potential use-after-free bug in posix timers - correct a prototype - address a build warning" * tag 'timers-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: posix-cpu-timers: Cleanup CPU timers before freeing them during exec time: Correct the prototype of ns_to_kernel_old_timeval and ns_to_timespec64 posix-timers: Make do_clock_gettime() static
2022-08-13Merge tag 'x86-urgent-2022-08-13' of ↵Linus Torvalds2-12/+27
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fix from Ingo Molnar: "Fix the 'IBPB mitigated RETBleed' mode of operation on AMD CPUs (not turned on by default), which also need STIBP enabled (if available) to be '100% safe' on even the shortest speculation windows" * tag 'x86-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/bugs: Enable STIBP for IBPB mitigated RETBleed
2022-08-13Merge tag 'i2c-for-5.20-part2' of ↵Linus Torvalds59-181/+370
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull more i2c updates from Wolfram Sang: - two driver fixes for issues introduced this cycle - one trivial driver improvement regarding ACPI - more DTS conversion and additions - documentation updates - subsystem-wide move from strlcpy to strscpy * tag 'i2c-for-5.20-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: docs: i2c: i2c-sysfs: fix hyperlinks docs: i2c: i2c-sysfs: improve wording docs: i2c: instantiating-devices: add syntax coloring to dts and C blocks docs: i2c: smbus-protocol: improve DataLow/DataHigh definition docs: i2c: i2c-protocol: remove unused legend items docs: i2c: i2c-protocol,smbus-protocol: remove nonsense words docs: i2c: i2c-protocol: update introductory paragraph i2c: move core from strlcpy to strscpy i2c: move drivers from strlcpy to strscpy i2c: kempld: Support ACPI I2C device declaration i2c: mediatek: add i2c compatible for MT8188 dt-bindings: i2c: update bindings for mt8188 soc i2c: microchip-corei2c: fix erroneous late ack send dt-bindings: i2c: qcom,i2c-cci: convert to dtschema i2c: qcom-geni: Fix GPI DMA buffer sync-back
2022-08-13Merge tag 'ntb-5.20' of https://github.com/jonmason/ntbLinus Torvalds14-25/+1822
Pull NTB updates from Jon Mason: "Non-Transparent Bridge updates. Fix of heap data and clang warnings, support for a new Intel NTB device, and NTB EndPoint Function (EPF) support and the various fixes for that" * tag 'ntb-5.20' of https://github.com/jonmason/ntb: MAINTAINERS: add PCI Endpoint NTB drivers to NTB files NTB: EPF: Tidy up some bounds checks NTB: EPF: Fix error code in epf_ntb_bind() PCI: endpoint: pci-epf-vntb: reduce several globals to statics PCI: endpoint: pci-epf-vntb: fix error handle in epf_ntb_mw_bar_init() PCI: endpoint: Fix Kconfig dependency NTB: EPF: set pointer addr to null using NULL rather than 0 Documentation: PCI: extend subheading underline for "lspci output" section Documentation: PCI: Use code-block block for scratchpad registers diagram Documentation: PCI: Add specification for the PCI vNTB function device PCI: endpoint: Support NTB transfer between RC and EP NTB: epf: Allow more flexibility in the memory BAR map method PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address ntb: intel: add GNR support for Intel PCIe gen5 NTB NTB: ntb_tool: uninitialized heap data in tool_fn_write() ntb: idt: fix clang -Wformat warnings
2022-08-13Merge tag 'xfs-5.20-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linuxLinus Torvalds5-46/+193
Pull more xfs updates from Darrick Wong: "There's not a lot this time around, just the usual bug fixes and corrections for missing error returns. - Return error codes from block device flushes to userspace - Fix a deadlock between reclaim and mount time quotacheck - Fix an unnecessary ENOSPC return when doing COW on a filesystem with severe free space fragmentation - Fix a miscalculation in the transaction reservation computations for file removal operations" * tag 'xfs-5.20-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: xfs: fix inode reservation space for removing transaction xfs: Fix false ENOSPC when performing direct write on a delalloc extent in cow fork xfs: fix intermittent hang during quotacheck xfs: check return codes when flushing block devices
2022-08-13Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds21-99/+124
Pull more SCSI updates from James Bottomley: "Mostly small bug fixes and trivial updates. The major new core update is a change to the way device, target and host reference counting is done to try to make it more robust (this change has soaked for a while to try to winkle out any bugs)" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: pm8001: Fix typo 'the the' in comment scsi: megaraid_sas: Remove redundant variable cmd_type scsi: FlashPoint: Remove redundant variable bm_int_st scsi: zfcp: Fix missing auto port scan and thus missing target ports scsi: core: Call blk_mq_free_tag_set() earlier scsi: core: Simplify LLD module reference counting scsi: core: Make sure that hosts outlive targets scsi: core: Make sure that targets outlive devices scsi: ufs: ufs-pci: Correct check for RESET DSM scsi: target: core: De-RCU of se_lun and se_lun acl scsi: target: core: Fix race during ACL removal scsi: ufs: core: Correct ufshcd_shutdown() flow scsi: ufs: core: Increase the maximum data buffer size scsi: lpfc: Check the return value of alloc_workqueue()
2022-08-13Merge tag 'block-6.0-2022-08-12' of git://git.kernel.dk/linux-blockLinus Torvalds6-7/+19
Pull block fixes from Jens Axboe: - NVMe pull request - print nvme connect Linux error codes properly (Amit Engel) - fix the fc_appid_store return value (Christoph Hellwig) - fix a typo in an error message (Christophe JAILLET) - add another non-unique identifier quirk (Dennis P. Kliem) - check if the queue is allocated before stopping it in nvme-tcp (Maurizio Lombardi) - restart admin queue if the caller needs to restart queue in nvme-fc (Ming Lei) - use kmemdup instead of kmalloc + memcpy in nvme-auth (Zhang Xiaoxu) - __alloc_disk_node() error handling fix (Rafael) * tag 'block-6.0-2022-08-12' of git://git.kernel.dk/linux-block: block: Do not call blk_put_queue() if gendisk allocation fails nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG GAMMIX S70 nvme-tcp: check if the queue is allocated before stopping it nvme-fabrics: Fix a typo in an error message nvme-fabrics: parse nvme connect Linux error codes nvmet-auth: use kmemdup instead of kmalloc + memcpy nvme-fc: fix the fc_appid_store return value nvme-fc: restart admin queue if the caller needs to restart queue
2022-08-13Merge tag 'io_uring-6.0-2022-08-13' of git://git.kernel.dk/linux-blockLinus Torvalds26-183/+178
Pull io_uring fixes from Jens Axboe: - Regression fix for this merge window, fixing a wrong order of arguments for io_req_set_res() for passthru (Dylan) - Fix for the audit code leaking context memory (Peilin) - Ensure that provided buffers are memcg accounted (Pavel) - Correctly handle short zero-copy sends (Pavel) - Sparse warning fixes for the recvmsg multishot command (Dylan) - Error handling fix for passthru (Anuj) - Remove randomization of struct kiocb fields, to avoid it growing in size if re-arranged in such a fashion that it grows more holes or padding (Keith, Linus) - Small series improving type safety of the sqe fields (Stefan) * tag 'io_uring-6.0-2022-08-13' of git://git.kernel.dk/linux-block: io_uring: add missing BUILD_BUG_ON() checks for new io_uring_sqe fields io_uring: make io_kiocb_to_cmd() typesafe fs: don't randomize struct kiocb fields io_uring: consistently make use of io_notif_to_data() io_uring: fix error handling for io_uring_cmd io_uring: fix io_recvmsg_prep_multishot sparse warnings io_uring/net: send retry for zerocopy io_uring: mem-account pbuf buckets audit, io_uring, io-wq: Fix memory leak in io_sq_thread() and io_wqe_worker() io_uring: pass correct parameters to io_req_set_res
2022-08-13perf test: Refactor shell tests allowing subdirsCarsten Haitzler4-134/+238
This is a prelude to adding more tests to shell tests and in order to support putting those tests into subdirectories, I need to change the test code that scans/finds and runs them. To support subdirs I have to recurse so it's time to refactor the code to allow this and centralize the shell script finding into one location and only one single scan that builds a list of all the found tests in memory instead of it being duplicated in 3 places. This code also optimizes things like knowing the max width of desciption strings (as we can do that while we scan instead of a whole new pass of opening files). It also more cleanly filters scripts to see only *.sh files thus skipping random other files in directories like *~ backup files, other random junk/data files that may appear and the scripts must be executable to make the cut (this ensures the script lib dir is not seen as scripts to run). This avoids perf test running previous older versions of test scripts that are editor backup files as well as skipping perf.data files that may appear and so on. Reviewed-by: Leo Yan <[email protected]> Signed-off-by: Carsten Haitzler <[email protected]> Tested-by: Leo Yan <[email protected]> Cc: Mathieu Poirier <[email protected]> Cc: Mike Leach <[email protected]> Cc: Suzuki Poulouse <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2022-08-13perf vendor events: Update events for snowridgexZhengjun Xing1-84/+27
Update the events to v1.20, update events for snowridgex by the latest event converter tools. Use script at: https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py to download and generate the latest events and metrics. Manually copy the snowridgex files into perf. Signed-off-by: Xing Zhengjun <[email protected]> Tested-by: Ian Rogers <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2022-08-13perf vendor events: Update events and metrics for skylakexZhengjun Xing4-1157/+24918
Update the events to v1.28, the metrics are based on TMA 4.4 full, update events and metrics for skylakex by the latest event converter tools. Use script at: https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py to download and generate the latest events and metrics. Manually copy the skylakex files into perf. Signed-off-by: Xing Zhengjun <[email protected]> Tested-by: Ian Rogers <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2022-08-13perf vendor events: Update metrics for sapphirerapidsZhengjun Xing1-0/+6
The metrics are based on TMA 4.4 full, add new metrics “UNCORE_FREQ” for sapphirerapids. Use script at: https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py to download and generate the latest events and metrics. Manually copy the sapphirerapids files into perf. Signed-off-by: Xing Zhengjun <[email protected]> Tested-by: Ian Rogers <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2022-08-13perf vendor events: Update events for knightslandingZhengjun Xing1-0/+213
Update the events to v9, update events for knightslanding by the latest event converter tools. Use script at: https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py to download and generate the latest events and metrics. Manually copy the knightslanding files into perf. Signed-off-by: Xing Zhengjun <[email protected]> Tested-by: Ian Rogers <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2022-08-13perf vendor events: Update metrics for jaketownZhengjun Xing1-0/+6
The metrics are based on TMA 4.4 full, add new metrics “UNCORE_FREQ” for jaketown. Use script at: https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py to download and generate the latest events and metrics. Manually copy the jaketown files into perf. Signed-off-by: Xing Zhengjun <[email protected]> Tested-by: Ian Rogers <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2022-08-13perf vendor events: Update metrics for ivytownZhengjun Xing1-0/+6
The metrics are based on TMA 4.4 full, add new metrics “UNCORE_FREQ” for ivytown. Use script at: https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py to download and generate the latest events and metrics. Manually copy the ivytown files into perf. Signed-off-by: Xing Zhengjun <[email protected]> Tested-by: Ian Rogers <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2022-08-13perf vendor events: Update events and metrics for icelakexZhengjun Xing4-556/+38332
Update the events to v1.15, the metrics are based on TMA 4.4 full, update events and metrics for icelakex by the latest event converter tools. Use script at: https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py to download and generate the latest events and metrics. Manually copy the icelakex files into perf. Signed-off-by: Xing Zhengjun <[email protected]> Tested-by: Ian Rogers <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
2022-08-13perf vendor events: Update events and metrics for haswellxZhengjun Xing2-171/+413
Update the events to v25, the metrics are based on TMA 4.4 full, update events and metrics for haswellx by the latest event converter tools. Use script at: https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py to download and generate the latest events and metrics. Manually copy the haswellx files into perf. Signed-off-by: Xing Zhengjun <[email protected]> Tested-by: Ian Rogers <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.