| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch makes g2d power domain and clock to be controlled
through pm runtime interfaces instead of controlling them
respectively.
Signed-off-by: Inki Dae <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
|
|
While trying to get boot-logo up on exynos5420 SMDK which has eDP panel
connected with resolution 2560x1600, following error occured even with
IOMMU enabled:
[0.880000] [drm:lowlevel_buffer_allocate] *ERROR* failed to allocate buffer.
[0.890000] [drm] Initialized exynos 1.0.0 20110530 on minor 0
To address the cases where physically contiguous memory MAY NOT be a
mandatory requirement for fb, the patch adds a feature to get non physically
contiguous memory for fb if physically contiguous memory allocation fails
and if IOMMU is supported.
Signed-off-by: Vikas Sajjan <[email protected]>
Signed-off-by: Arun Kumar <[email protected]>
Reviewed-by: Rob Clark <[email protected]>
Signed-off-by: Inki Dae <[email protected]>
|
|
Previously, we experience bio traces as follows when running simple sequential
write test.
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500104928, size = 4K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 499922208, size = 368K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 499914752, size = 140K
-> total 512K
The first one is to write an indirect node block, and the others are to write
direct node blocks.
The reason why there are two separate bios for direct node blocks is:
0. initial state
------------------ ------------------
| | |xxxxxxxx |
------------------ ------------------
1. write 368K
------------------ ------------------
| | |xxxxxxxxWWWWWWWW|
------------------ ------------------
2. write 140K
------------------ ------------------
|WWWWWWW | |xxxxxxxxWWWWWWWW|
------------------ ------------------
This is because f2fs_write_node_pages tries to write just 512K totally, so that
we can lose the chance to merge more bios nicely.
After this patch is applied, we can get the following bio traces.
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500103168, size = 8K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500111368, size = 4K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500107272, size = 512K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500108296, size = 512K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500109320, size = 500K
And finally, we can improve the sequential write performance,
from 458.775 MB/s to 479.945 MB/s on SSD.
Signed-off-by: Jaegeuk Kim <[email protected]>
|
|
Pull KVM updates from Gleb Natapov:
"The highlights of the release are nested EPT and pv-ticketlocks
support (hypervisor part, guest part, which is most of the code, goes
through tip tree). Apart of that there are many fixes for all arches"
Fix up semantic conflicts as discussed in the pull request thread..
* 'next' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (88 commits)
ARM: KVM: Add newlines to panic strings
ARM: KVM: Work around older compiler bug
ARM: KVM: Simplify tracepoint text
ARM: KVM: Fix kvm_set_pte assignment
ARM: KVM: vgic: Bump VGIC_NR_IRQS to 256
ARM: KVM: Bugfix: vgic_bytemap_get_reg per cpu regs
ARM: KVM: vgic: fix GICD_ICFGRn access
ARM: KVM: vgic: simplify vgic_get_target_reg
KVM: MMU: remove unused parameter
KVM: PPC: Book3S PR: Rework kvmppc_mmu_book3s_64_xlate()
KVM: PPC: Book3S PR: Make instruction fetch fallback work for system calls
KVM: PPC: Book3S PR: Don't corrupt guest state when kernel uses VMX
KVM: x86: update masterclock when kvmclock_offset is calculated (v2)
KVM: PPC: Book3S: Fix compile error in XICS emulation
KVM: PPC: Book3S PR: return appropriate error when allocation fails
arch: powerpc: kvm: add signed type cast for comparation
KVM: x86: add comments where MMIO does not return to the emulator
KVM: vmx: count exits to userspace during invalid guest emulation
KVM: rename __kvm_io_bus_sort_cmp to kvm_io_bus_cmp
kvm: optimize away THP checks in kvm_is_mmio_pfn()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from Konrad Rzeszutek Wilk:
"A couple of features and a ton of bug-fixes. There is also some
maintership changes. Jeremy is enjoying the full-time work at the
startup and as much as he would love to help - he can't find the time.
I have a bunch of other things that I promised to work on - paravirt
diet, get SWIOTLB working everywhere, etc, but haven't been able to
find the time.
As such both David Vrabel and Boris Ostrovsky have graciously
volunteered to help with the maintership role. They will keep the lid
on regressions, bug-fixes, etc. I will be in the background to help -
but eventually there will be less of me doing the Xen GIT pulls and
more of them. Stefano is still doing the ARM/ARM64 and will continue
on doing so.
Features:
- Xen Trusted Platform Module (TPM) frontend driver - with the
backend in MiniOS.
- Scalability improvements in event channel.
- Two extra Xen co-maintainers (David, Boris) and one going away (Jeremy)
Bug-fixes:
- Make the 1:1 mapping work during early bootup on selective regions.
- Add scratch page to balloon driver to deal with unexpected code
still holding on stale pages.
- Allow NMIs on PV guests (64-bit only)
- Remove unnecessary TLB flush in M2P code.
- Fixes duplicate callbacks in Xen granttable code.
- Fixes in PRIVCMD_MMAPBATCH ioctls to allow retries
- Fix for events being lost due to rescheduling on different VCPUs.
- More documentation"
* tag 'stable/for-linus-3.12-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (23 commits)
hvc_xen: Remove unnecessary __GFP_ZERO from kzalloc
drivers/xen-tpmfront: Fix compile issue with missing option.
xen/balloon: don't set P2M entry for auto translated guest
xen/evtchn: double free on error
Xen: Fix retry calls into PRIVCMD_MMAPBATCH*.
xen/pvhvm: Initialize xen panic handler for PVHVM guests
xen/m2p: use GNTTABOP_unmap_and_replace to reinstate the original mapping
xen: fix ARM build after 6efa20e4
MAINTAINERS: Remove Jeremy from the Xen subsystem.
xen/events: document behaviour when scanning the start word for events
x86/xen: during early setup, only 1:1 map the ISA region
x86/xen: disable premption when enabling local irqs
swiotlb-xen: replace dma_length with sg_dma_len() macro
swiotlb: replace dma_length with sg_dma_len() macro
xen/balloon: set a mapping for ballooned out pages
xen/evtchn: improve scalability by using per-user locks
xen/p2m: avoid unneccesary TLB flush in m2p_remove_override()
MAINTAINERS: Add in two extra co-maintainers of the Xen tree.
MAINTAINERS: Update the Xen subsystem's with proper mailing list.
xen: replace strict_strtoul() with kstrtoul()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Minor fixes mainly, including a potential use-after-free on remove
found by CONFIG_DEBUG_KOBJECT_RELEASE which may be theoretical"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: Fix mod->mkobj.kobj potentially freed too early
kernel/params.c: use scnprintf() instead of sprintf()
kernel/module.c: use scnprintf() instead of sprintf()
module/lsm: Have apparmor module parameters work with no args
module: Add NOARG flag for ops with param_set_bool_enable_only() set function
module: Add flag to allow mod params to have no arguments
modules: add support for soft module dependencies
scripts/mod/modpost.c: permit '.cranges' secton for sh64 architecture.
module: fix sprintf format specifier in param_get_byte()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm updates from David Teigland:
"This set includes a workqueue cleanup and the removal of incorrect and
unneeded signal blocking"
* tag 'dlm-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: remove signal blocking
dlm: WQ_NON_REENTRANT is meaningless and going away
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"New features for 3.12:
- Added aggressive extent caching using the extent status tree. This
can actually decrease memory usage in read-mostly workloads since
the information is much more compactly stored in the extent status
tree than if we had to keep the extent tree metadata blocks in the
buffer cache. This also improves Asynchronous I/O since it is it
makes much less likely that we need to do metadata I/O to lookup
the extent tree information.
- Improve the recovery after corrupted allocation bitmaps are found
when running in errors=ignore mode.
Also fixed some writeback vs truncate races when using a blocksize
less than the page size"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (25 commits)
ext4: allow specifying external journal by pathname mount option
ext4: mark group corrupt on group descriptor checksum
ext4: mark block group as corrupt on inode bitmap error
ext4: mark block group as corrupt on block bitmap error
ext4: fix type declaration of ext4_validate_block_bitmap
ext4: error out if verifying the block bitmap fails
jbd2: Fix endian mixing problems in the checksumming code
ext4: isolate ext4_extents.h file
ext4: Fix misspellings using 'codespell' tool
ext4: convert write_begin methods to stable_page_writes semantics
ext4: fix use of potentially uninitialized variables in debugging code
ext4: fix lost truncate due to race with writeback
ext4: simplify truncation code in ext4_setattr()
ext4: fix ext4_writepages() in presence of truncate
ext4: move test whether extent to map can be extended to one place
ext4: fix warning in ext4_da_update_reserve_space()
quota: provide interface for readding allocated space into reserved space
ext4: avoid reusing recently deleted inodes in no journal mode
ext4: allocate delayed allocation blocks before rename
ext4: start handle at least possible moment when renaming files
...
|
|
All the cool kids are doing this, join in the fun.
Signed-off-by: Tony Luck <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Changes are seen in a wide range of codes, mainly due to ASoC DAPM
requirements; HD-audio shows a high peak in diffstat, it's just a
removal of bunch of old static quirks.
Some highlights:
- HDPM: Updates for AIO/RayDAT support, TCO/sync support
- RME96: Add PCM sync support
- HD-audio:
* A few HDMI/DP audio updates (CA assignment fix, stream switching
fix, Intel DP device list support)
* Device specific fixes (ASUS/CXT HP mic support, Thinkpad mic
improvements, Chromebook fixes, STAC9228 Dell fixes)
* Replace the all static quirks for AD codecs with the generic
parser
* WAKEEN support for handling irqs in the power saving mode
- USB-audio: Clean up implicit fb handling and related codes
- DAPM is now mandatory for ASoC CODEC drivers; all existing drivers
have had some level of DAPM support added. In addition, a lot of
cleanups and improvements in DAPM.
- Support for ASoC cross-platform compile test
- New drivers and support for Analog Devices ADAU1702 and
ADAU1401(a), Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and
WM8904 based machines, Freescale S/PDIF and SSI AC'97, Renesas
R-Car SoCs, Samsung Exynos5420 SoCs, Texas Instruments PCM1681 and
PCM1792A and Wolfson Microelectronics WM8997
- DT bindings for kirkwood and i.MX S/PDIF
- Clean up and bug fixes: ssm2602, rt5640 and sgtl5000.
- Core helpers for bitbanged AC'97 reset"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (375 commits)
ALSA: hda - Re-setup HDMI pin and audio infoframe on stream switches
ALSA: hda - hdmi: Fallback to ALSA allocation when selecting CA
ASoC: mxs-sgtl5000: Configure the dai_links as unidirectional
ASoC: soc-pcm: Allow to specify unidirectional dai_link
ASoC: fsl_spdif: Staticse non-exported symbols
ASoC: ssm2602: Fix cache sync
ASoC: Remove unused sysfs_registered field from snd_soc_codec struct
ASoC: Remove unused debugfs_dapm field from snd_soc_{platform,codec} struct
ASoC: Remove unused control_type field from snd_soc_codec struct
ASoC: fsl: Add one blank space after ':=' in Makefile
ASoC: fsl: Add wrapping for dev_dbg() in fsl_spdif.c
ASoC: rt5640: change widget sequence for depop
ASoC: dapm: Fix auto-disable for inverted controls
ASoC: fsl: Drop SND_SOC_FSL_UTILS from SND_SOC_IMX_SPDIF
ASoC: Samsung: Do not queue cyclic buffers multiple times
ASoC: ep93xx-i2s: Remove unnecessary dev_set_drvdata()
ASoC: designware_i2s: Remove unnecessary dev_set_drvdata()
ASoC: fsl_spdif: remove redundant dev_err call in fsl_spdif_probe()
ASoC: fsl: Add S/PDIF machine driver
ASoc: kirkwood: Use the Kirkwood audio driver in Dove boards
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"Here is the bulk of pin control changes for the v3.12 series. Most of
the relevant information is in the tag.
I merged in v3.11-rc7 last week to get rid of a largeish conflict
within the sunxi (AllWinner) driver in linux-next and fix up the
non-trivial merge the right way. That driver had a rather large fix
adding locking late in the release cycle.
Overall the bulk changes this time is cleanups and refactorings and
not much new features, which is nice.
- Refactorings for generic pin config handling in the core.
- Factor out a set of device tree utilities for use in all drivers,
to parse and allocate maps from the device tree.
- Some fixes to the core such as more nitpicky locking.
- Pushed down config array iteration into the drivers.
This patch is necessary for drivers that want to iterate over
configs and pile up a stack of alterations to the same register(s),
or if the driver wants to take a local spinlock when committing the
configuration.
- A new driver for the Texas Instruments Palmas PMIC by Laxman
Dewangan. This is used on the Tegra systems.
- A major cleanup and modernization of the PFC (Super Hitachi and ARM
SHmobile) pin controller and subdrivers.
- Support for the A20 and A31 sunxi (AllWinner) SoCs.
- A huge pile of fixes and cleanups: Axel Lin, Jingoo Han Dan
Carpenter, Julia Lawall and Sachin Kamat did an excellent job here"
* tag 'pinctrl-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (124 commits)
pinctrl: sunxi: Fix off-by-one for valid offset range checking
pinctrl: sunxi: drop lock on error path
pinctrl: pinconf-generic: Remove ti prefix in dev_err messages
pinctrl: rockchip: Implement .request() and .free() callbacks
pinctrl: at91: fix get_pullup/down function return
pinctrl: sh-pfc: remove unnecessary platform_set_drvdata()
pinctrl: Add s5pv210 support to pinctrl-exynos
pinctrl: utils: include export.h to avoid warnings
pinctrl: s3c24xx: off by one in s3c24xx_eint_init()
pinctrl: mvebu: testing the wrong variable
pinctrl: abx500: fix bitwise AND test
pinctrl: mvebu: Convert to use devm_ioremap_resource
pinctrl: Pass all configs to driver on pin_config_set()
pinctrl: tz1090-pdc: Convert to devm_ioremap_resource
pinctrl: tz1090: Convert to devm_ioremap_resource
pinctrl: tegra: Convert to devm_ioremap_resource
pinctrl: rockchip: Simplify pin_to_bank equation
pinctrl: spear: Convert to devm_ioremap_resource
pinctrl: rockchip: Remove of_match_ptr macro for DT only driver
pinctrl: palmas: PINCTRL_PALMAS needs to select PINMUX
...
|
|
Suppress warning of unused-variables by adding a BUG()+return for invalid
audio-formats.
Cc: Rob Clark <[email protected]>
Signed-off-by: David Herrmann <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
Signed-off-by: Stephen Rothwell <[email protected]>
Acked-by: Alex Deucher <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
While implementing NAPI for the driver, I overlooked the race conditions where
interrupt handler might have called napi_schedule_prep() before napi_enable()
was called or after napi_disable() was called. If RX interrupt happens, this
would cause the endless interrupts and messages like:
sh-eth eth0: ignoring interrupt, status 0x00040000, mask 0x01ff009f.
The interrupt wouldn't even be masked by the kernel eventually since the handler
would return IRQ_HANDLED all the time.
As a fix, move napi_enable() call before request_irq() call and napi_disable()
call after free_irq() call.
Signed-off-by: Sergei Shtylyov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 spinlock changes from Ingo Molnar:
"The biggest change here are paravirtualized ticket spinlocks (PV
spinlocks), which bring a nice speedup on various benchmarks.
The KVM host side will come to you via the KVM tree"
* 'x86-spinlocks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kvm/guest: Fix sparse warning: "symbol 'klock_waiting' was not declared as static"
kvm: Paravirtual ticketlocks support for linux guests running on KVM hypervisor
kvm guest: Add configuration support to enable debug information for KVM Guests
kvm uapi: Add KICK_CPU and PV_UNHALT definition to uapi
xen, pvticketlock: Allow interrupts to be enabled while blocking
x86, ticketlock: Add slowpath logic
jump_label: Split jumplabel ratelimit
x86, pvticketlock: When paravirtualizing ticket locks, increment by 2
x86, pvticketlock: Use callee-save for lock_spinning
xen, pvticketlocks: Add xen_nopvspin parameter to disable xen pv ticketlocks
xen, pvticketlock: Xen implementation for PV ticket locks
xen: Defer spinlock setup until boot CPU setup
x86, ticketlock: Collapse a layer of functions
x86, ticketlock: Don't inline _spin_unlock when using paravirt spinlocks
x86, spinlock: Replace pv spinlocks with pv ticketlocks
|
|
Document force_mld_version parameter in ip-sysctl.txt.
Signed-off-by: Daniel Borkmann <[email protected]>
Cc: Hannes Frederic Sowa <[email protected]>
Acked-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We already have mld_{gq,ifc,dad}_start_timer() functions, so introduce
mld_{gq,ifc,dad}_stop_timer() functions to reduce code size and make it
more readable.
Signed-off-by: Daniel Borkmann <[email protected]>
Cc: Hannes Frederic Sowa <[email protected]>
Acked-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Make igmp6_event_query() a bit easier to read by refactoring code
parts into mld_process_v1() and mld_process_v2().
Signed-off-by: Daniel Borkmann <[email protected]>
Cc: Hannes Frederic Sowa <[email protected]>
Acked-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Similarly as we do in MLDv2 queries, set a forged MLDv1 query with
0 ms mld_maxdelay to minimum timer shot time of 1 jiffies. This is
eventually done in igmp6_group_queried() anyway, so we can simplify
a check there.
Signed-off-by: Daniel Borkmann <[email protected]>
Cc: Hannes Frederic Sowa <[email protected]>
Acked-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
RFC3810, 10. Security Considerations says under subsection 10.1.
Query Message:
A forged Version 1 Query message will put MLDv2 listeners on that
link in MLDv1 Host Compatibility Mode. This scenario can be avoided
by providing MLDv2 hosts with a configuration option to ignore
Version 1 messages completely.
Hence, implement a MLDv2-only mode that will ignore MLDv1 traffic:
echo 2 > /proc/sys/net/ipv6/conf/ethX/force_mld_version or
echo 2 > /proc/sys/net/ipv6/conf/all/force_mld_version
Note that <all> device has a higher precedence as it was previously
also the case in the macro MLD_V1_SEEN() that would "short-circuit"
if condition on <all> case.
Signed-off-by: Daniel Borkmann <[email protected]>
Cc: Hannes Frederic Sowa <[email protected]>
Acked-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Get rid of MLDV2_MRC and use our new macros for mantisse and
exponent to calculate Maximum Response Delay out of the Maximum
Response Code.
Signed-off-by: Daniel Borkmann <[email protected]>
Cc: Hannes Frederic Sowa <[email protected]>
Acked-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Replace the macro with a function to make it more readable. GCC will
eventually decide whether to inline this or not (also, that's not
fast-path anyway).
Signed-off-by: Daniel Borkmann <[email protected]>
Cc: Hannes Frederic Sowa <[email protected]>
Acked-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
i) RFC3810, 9.2. Query Interval [QI] says:
The Query Interval variable denotes the interval between General
Queries sent by the Querier. Default value: 125 seconds. [...]
ii) RFC3810, 9.3. Query Response Interval [QRI] says:
The Maximum Response Delay used to calculate the Maximum Response
Code inserted into the periodic General Queries. Default value:
10000 (10 seconds) [...] The number of seconds represented by the
[Query Response Interval] must be less than the [Query Interval].
iii) RFC3810, 9.12. Older Version Querier Present Timeout [OVQPT] says:
The Older Version Querier Present Timeout is the time-out for
transitioning a host back to MLDv2 Host Compatibility Mode. When an
MLDv1 query is received, MLDv2 hosts set their Older Version Querier
Present Timer to [Older Version Querier Present Timeout].
This value MUST be ([Robustness Variable] times (the [Query Interval]
in the last Query received)) plus ([Query Response Interval]).
Hence, on *default* the timeout results in:
[RV] = 2, [QI] = 125sec, [QRI] = 10sec
[OVQPT] = [RV] * [QI] + [QRI] = 260sec
Having that said, we currently calculate [OVQPT] (here given as 'switchback'
variable) as ...
switchback = (idev->mc_qrv + 1) * max_delay
RFC3810, 9.12. says "the [Query Interval] in the last Query received". In
section "9.14. Configuring timers", it is said:
This section is meant to provide advice to network administrators on
how to tune these settings to their network. Ambitious router
implementations might tune these settings dynamically based upon
changing characteristics of the network. [...]
iv) RFC38010, 9.14.2. Query Interval:
The overall level of periodic MLD traffic is inversely proportional
to the Query Interval. A longer Query Interval results in a lower
overall level of MLD traffic. The value of the Query Interval MUST
be equal to or greater than the Maximum Response Delay used to
calculate the Maximum Response Code inserted in General Query
messages.
I assume that was why switchback is calculated as is (3 * max_delay), although
this setting seems to be meant for routers only to configure their [QI]
interval for non-default intervals. So usage here like this is clearly wrong.
Concluding, the current behaviour in IPv6's multicast code is not conform
to the RFC as switch back is calculated wrongly. That is, it has a too small
value, so MLDv2 hosts switch back again to MLDv2 way too early, i.e. ~30secs
instead of ~260secs on default.
Hence, introduce necessary helper functions and fix this up properly as it
should be.
Introduced in 06da92283 ("[IPV6]: Add MLDv2 support."). Credits to Hannes
Frederic Sowa who also had a hand in this as well. Also thanks to Hangbin Liu
who did initial testing.
Signed-off-by: Daniel Borkmann <[email protected]>
Cc: David Stevens <[email protected]>
Cc: Hannes Frederic Sowa <[email protected]>
Acked-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In tcp_v6_do_rcv() code, when processing pkt options, we soley work
on our skb clone opt_skb that we've created earlier before entering
tcp_rcv_established() on our way. However, only in condition ...
if (np->rxopt.bits.rxtclass)
np->rcv_tclass = ipv6_get_dsfield(ipv6_hdr(skb));
... we work on skb itself. As we extract every other information out
of opt_skb in ipv6_pktoptions path, this seems wrong, since skb can
already be released by tcp_rcv_established() earlier on. When we try
to access it in ipv6_hdr(), we will dereference freed skb.
[ Bug added by commit 4c507d2897bd9b ("net: implement IP_RECVTOS for
IP_PKTOPTIONS") ]
Signed-off-by: Daniel Borkmann <[email protected]>
Cc: Eric Dumazet <[email protected]>
Acked-by: Eric Dumazet <[email protected]>
Acked-by: Jiri Benc <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit 1b7fdd2ab585("tcp: do not use cached RTT for RTT estimation")
removes important comments on how RTO is initialized and updated.
Hopefully this patch puts those information back.
Signed-off-by: Yuchung Cheng <[email protected]>
Acked-by: Neal Cardwell <[email protected]>
Acked-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
vxlan-udp-recv function lookup vxlan_sock struct on every packet
recv by using udp-port number. we can use sk->sk_user_data to
store vxlan_sock and avoid lookup.
I have open coded rcu-api to store and read vxlan_sock from
sk_user_data to avoid sparse warning as sk_user_data is not
__rcu pointer.
Signed-off-by: Pravin B Shelar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: Andy Shevchenko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There is a nice helper to parse MAC. Let's use it and remove custom
implementation.
Signed-off-by: Andy Shevchenko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Allocating skbs when sending out neighbour discovery messages
currently uses sock_alloc_send_skb() based on a per net namespace
socket and thus share a socket wmem buffer space.
If a netdevice is temporarily unable to transmit due to carrier
loss or for other reasons, the queued up ndisc messages will cosnume
all of the wmem space and will thus prevent from any more skbs to
be allocated even for netdevices that are able to transmit packets.
The number of neighbour discovery messages sent is very limited,
use of alloc_skb() bypasses the socket wmem buffer size enforcement
while the manual call to skb_set_owner_w() maintains the socket
reference needed for the IPv6 output path.
This patch has orginally been posted by Eric Dumazet in a modified
form.
Signed-off-by: Thomas Graf <[email protected]>
Cc: Eric Dumazet <[email protected]>
Cc: Hannes Frederic Sowa <[email protected]>
Cc: Stephen Warren <[email protected]>
Cc: Fabio Estevam <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
Tested-by: Stephen Warren <[email protected]>
Acked-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Time stamp binary rollover is set.
The synopsys spec says When TSCRLSSR is cleard, the rollover value of
sub-second register is 0x7FFFFFFF(0.465 ns per clock).
Signed-off-by: Sonic Zhang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Bug: error to get the previous BD entry. When the current BD
is the first BD, the previous BD entry must be the last BD,
not "bdp - 1" in current logic.
V4:
* Optimize fec_enet_get_nextdesc() for code clean.
Replace "ex_new_bd - ring_size" with "ex_base".
Replace "new_bd - ring_size" with "base".
V3:
* Restore the API name because David suggest to use fec_enet_
prefix for all function in fec driver.
So, change next_bd() -> fec_enet_get_nextdesc()
change pre_bd() -> fec_enet_get_prevdesc()
* Reduce the two APIs parameters for easy to call.
V2:
* Add tx_ring_size and rx_ring_size to struct fec_enet_private.
* Replace api fec_enet_get_nextdesc() with next_bd().
Replace api fec_enet_get_prevdesc() with pre_bd().
* Move all ring size check logic to next_bd() and pre_bd(), which
simplifies the code redundancy.
V1:
* Add BD ring size check to get the previous BD entry in correctly.
Reviewed-by: Li Frank <[email protected]>
Signed-off-by: Fugang Duan <[email protected]>
Acked-by: Frank Li <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit b67bfe0d42cac56c512dd5da4b1b347a23f4b70a ("hlist: drop
the node parameter from iterators") changed the behavior of
hlist_for_each_entry_safe to leave the p argument NULL.
Fix this up by tracking the last argument.
Reported-by: Michele Baldessari <[email protected]>
Cc: Hideaki YOSHIFUJI <[email protected]>
Cc: Sasha Levin <[email protected]>
Signed-off-by: Hannes Frederic Sowa <[email protected]>
Tested-by: Michele Baldessari <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Driver supporting NAPI should use NAPI-specific function for receiving packets,
so netif_rx() should be changed to netif_receive_skb().
Signed-off-by: Sergei Shtylyov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 SMAP fixes from Ingo Molnar:
"Fixes for Intel SMAP support, to fix SIGSEGVs during bootup"
* 'x86-smap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Introduce [compat_]save_altstack_ex() to unbreak x86 SMAP
x86, smap: Handle csum_partial_copy_*_user()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 RAS changes from Ingo Molnar:
"[ The reason for drivers/ updates is that Boris asked for the
drivers/edac/ changes to go via x86/ras in this cycle ]
Main changes:
- AMD CPUs:
. Add ECC event decoding support for new F15h models
. Various erratum fixes
. Fix single-channel on dual-channel-controllers bug.
- Intel CPUs:
. UC uncorrectable memory error parsing fix
. Add support for CMC (Corrected Machine Check) 'FF' (Firmware
First) flag in the APEI HEST
- Various cleanups and fixes"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
amd64_edac: Fix incorrect wraparounds
amd64_edac: Correct erratum 505 range
cpc925_edac: Use proper array termination
x86/mce, acpi/apei: Only disable banks listed in HEST if mce is configured
amd64_edac: Get rid of boot_cpu_data accesses
amd64_edac: Add ECC decoding support for newer F15h models
x86, amd_nb: Clarify F15h, model 30h GART and L3 support
pci_ids: Add PCI device ID functions 3 and 4 for newer F15h models.
x38_edac: Make a local function static
i3200_edac: Make a local function static
x86/mce: Pay no attention to 'F' bit in MCACOD when parsing 'UC' errors
APEI/ERST: Fix error message formatting
amd64_edac: Fix single-channel setups
EDAC: Replace strict_strtol() with kstrtol()
mce: acpi/apei: Soft-offline a page on firmware GHES notification
mce: acpi/apei: Add a boot option to disable ff mode for corrected errors
mce: acpi/apei: Honour Firmware First for MCA banks listed in APEI HEST CMC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 platform documentation fix from Ingo Molnar.
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/acpi: Correct out-of-date comment of __acpi_map_table()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 paravirt changes from Ingo Molnar:
"Hypervisor signature detection cleanup and fixes - the goal is to make
KVM guests run better on MS/Hyperv and to generalize and factor out
the code a bit"
* 'x86-paravirt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Correctly detect hypervisor
x86, kvm: Switch to use hypervisor_cpuid_base()
xen: Switch to use hypervisor_cpuid_base()
x86: Introduce hypervisor_cpuid_base()
|
|
multiple of 4
net: sctp: Fix data chunk fragmentation for MTU values which are not multiple of 4
Initially the problem was observed with ipsec, but later it became clear that
SCTP data chunk fragmentation algorithm has problems with MTU values which are
not multiple of 4. Test program was used which just transmits 2000 bytes long
packets to other host. tcpdump was used to observe re-fragmentation in IP layer
after SCTP already fragmented data chunks.
With MTU 1500:
12:54:34.082904 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 1500)
10.151.38.153.39303 > 10.151.24.91.54321: sctp (1) [DATA] (B) [TSN: 2366088589] [SID: 0] [SSEQ 1] [PPID 0x0]
12:54:34.082933 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 596)
10.151.38.153.39303 > 10.151.24.91.54321: sctp (1) [DATA] (E) [TSN: 2366088590] [SID: 0] [SSEQ 1] [PPID 0x0]
12:54:34.090576 IP (tos 0x2,ECT(0), ttl 63, id 0, offset 0, flags [DF], proto SCTP (132), length 48)
10.151.24.91.54321 > 10.151.38.153.39303: sctp (1) [SACK] [cum ack 2366088590] [a_rwnd 79920] [#gap acks 0] [#dup tsns 0]
With MTU 1499:
13:02:49.955220 IP (tos 0x2,ECT(0), ttl 64, id 48215, offset 0, flags [+], proto SCTP (132), length 1492)
10.151.38.153.39084 > 10.151.24.91.54321: sctp[|sctp]
13:02:49.955249 IP (tos 0x2,ECT(0), ttl 64, id 48215, offset 1472, flags [none], proto SCTP (132), length 28)
10.151.38.153 > 10.151.24.91: ip-proto-132
13:02:49.955262 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 600)
10.151.38.153.39084 > 10.151.24.91.54321: sctp (1) [DATA] (E) [TSN: 404355346] [SID: 0] [SSEQ 1] [PPID 0x0]
13:02:49.956770 IP (tos 0x2,ECT(0), ttl 63, id 0, offset 0, flags [DF], proto SCTP (132), length 48)
10.151.24.91.54321 > 10.151.38.153.39084: sctp (1) [SACK] [cum ack 404355346] [a_rwnd 79920] [#gap acks 0] [#dup tsns 0]
Here problem in data portion limit calculation leads to re-fragmentation in IP,
which is sub-optimal. The problem is max_data initial value, which doesn't take
into account the fact, that data chunk must be padded to 4-bytes boundary.
It's enough to correct max_data, because all later adjustments are correctly
aligned to 4-bytes boundary.
After the fix is applied, everything is fragmented correctly for uneven MTUs:
15:16:27.083881 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 1496)
10.151.38.153.53417 > 10.151.24.91.54321: sctp (1) [DATA] (B) [TSN: 3077098183] [SID: 0] [SSEQ 1] [PPID 0x0]
15:16:27.083907 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 600)
10.151.38.153.53417 > 10.151.24.91.54321: sctp (1) [DATA] (E) [TSN: 3077098184] [SID: 0] [SSEQ 1] [PPID 0x0]
15:16:27.085640 IP (tos 0x2,ECT(0), ttl 63, id 0, offset 0, flags [DF], proto SCTP (132), length 48)
10.151.24.91.54321 > 10.151.38.153.53417: sctp (1) [SACK] [cum ack 3077098184] [a_rwnd 79920] [#gap acks 0] [#dup tsns 0]
The bug was there for years already, but
- is a performance issue, the packets are still transmitted
- doesn't show up with default MTU 1500, but possibly with ipsec (MTU 1438)
Signed-off-by: Alexander Sverdlin <[email protected]>
Acked-by: Vlad Yasevich <[email protected]>
Acked-by: Neil Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Free_irq is not needed if there has been no request_irq. Free_irq is
removed from both the probe and remove functions. The correct request_irq
and free_irq are found in the open and close functions.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
*e = platform_get_irq(...);
... when != request_irq(e,...)
*free_irq(e,...)
// </smpl>
Signed-off-by: Julia Lawall <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Solution:
=========
- Synchronize linux's `include/uapi/linux/in6.h'
with glibc's `inet/netinet/in.h'.
- Synchronize glibc's `inet/netinet/in.h with linux's
`include/uapi/linux/in6.h'.
- Allow including the headers in either other.
- First header included defines the structures and macros.
Details:
========
The kernel promises not to break the UAPI ABI so I don't
see why we can't just have the two userspace headers
coordinate?
If you include the kernel headers first you get those,
and if you include the glibc headers first you get those,
and the following patch arranges a coordination and
synchronization between the two.
Let's handle `include/uapi/linux/in6.h' from linux,
and `inet/netinet/in.h' from glibc and ensure they compile
in any order and preserve the required ABI.
These two patches pass the following compile tests:
cat >> test1.c <<EOF
int main (void) {
return 0;
}
EOF
gcc -c test1.c
cat >> test2.c <<EOF
int main (void) {
return 0;
}
EOF
gcc -c test2.c
One wrinkle is that the kernel has a different name for one of
the members in ipv6_mreq. In the kernel patch we create a macro
to cover the uses of the old name, and while that's not entirely
clean it's one of the best solutions (aside from an anonymous
union which has other issues).
I've reviewed the code and it looks to me like the ABI is
assured and everything matches on both sides.
Notes:
- You want netinet/in.h to include bits/in.h as early as possible,
but it needs in_addr so define in_addr early.
- You want bits/in.h included as early as possible so you can use
the linux specific code to define __USE_KERNEL_DEFS based on
the _UAPI_* macro definition and use those to cull in.h.
- glibc was missing IPPROTO_MH, added here.
Compile tested and inspected.
Reported-by: Thomas Backlund <[email protected]>
Cc: Thomas Backlund <[email protected]>
Cc: [email protected]
Cc: YOSHIFUJI Hideaki <[email protected]>
Cc: David S. Miller <[email protected]>
Tested-by: Cong Wang <[email protected]>
Signed-off-by: Carlos O'Donell <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It upsets static analyzers when we don't check for allocation failure.
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
DEF_NATIVE() is defined in paravirt_types.h, remove duplicate
definition in paravirt.c
Reported-by: Linus Torvalds <[email protected]>
Signed-off-by: H. Peter Anvin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Konrad Rzeszutek Wilk <[email protected]>
Link: http://lkml.kernel.org/r/CA%2B55aFxVv==DC0JdS87V%2BcPr-twN%[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
This series contains updates to igb only.
Todd provides a fix for igb to not look for a PBA in the iNVM on
devices that are flashless.
Akeem provides igb patches to add a new PHY id for i354, as well as
a couple of patches to implement the new PHY id. He also provides
several patches to correctly report the appropriate media type as
well as correctly report advertised/supported link for i354 devices.
Lastly Akeem implements a 1 second delay mechanism for i210 devices
to avoid erroneous link issue with the link partner.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm changes from Ingo Molnar:
"Misc smaller fixes:
- a parse_setup_data() boot crash fix
- a memblock and an __early_ioremap cleanup
- turn the always-on CONFIG_ARCH_MEMORY_PROBE=y into a configurable
option and turn it off - it's an unrobust debug facility, it
shouldn't be enabled by default"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: avoid remapping data in parse_setup_data()
x86: Use memblock_set_current_limit() to set limit for memblock.
mm: Remove unused variable idx0 in __early_ioremap()
mm/hotplug, x86: Disable ARCH_MEMORY_PROBE by default
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 relocation changes from Ingo Molnar:
"This tree contains a single change, ELF relocation handling in C - one
of the kernel randomization patches that makes sense even without
randomization present upstream"
* 'x86-kaslr-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, relocs: Move ELF relocation handling to C
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timers/nohz changes from Ingo Molnar:
"It mostly contains fixes and full dynticks off-case optimizations, by
Frederic Weisbecker"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
nohz: Include local CPU in full dynticks global kick
nohz: Optimize full dynticks's sched hooks with static keys
nohz: Optimize full dynticks state checks with static keys
nohz: Rename a few state variables
vtime: Always debug check snapshot source _before_ updating it
vtime: Always scale generic vtime accounting results
vtime: Optimize full dynticks accounting off case with static keys
vtime: Describe overriden functions in dedicated arch headers
m68k: hardirq_count() only need preempt_mask.h
hardirq: Split preempt count mask definitions
context_tracking: Split low level state headers
vtime: Fix racy cputime delta update
vtime: Remove a few unneeded generic vtime state checks
context_tracking: User/kernel broundary cross trace events
context_tracking: Optimize context switch off case with static keys
context_tracking: Optimize guest APIs off case with static key
context_tracking: Optimize main APIs off case with static key
context_tracking: Ground setup for static key use
context_tracking: Remove full dynticks' hacky dependency on wide context tracking
nohz: Only enable context tracking on full dynticks CPUs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
The following batch contains:
* Three fixes for the new synproxy target available in your
net-next tree, from Jesper D. Brouer and Patrick McHardy.
* One fix for TCPMSS to correctly handling the fragmentation
case, from Phil Oester. I'll pass this one to -stable.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fb changes from Ingo Molnar:
"This tree includes preparatory patches for SimpleDRM driver support,
by David Herrmann. They clean up x86 framebuffer support by creating
simplefb devices wherever possible. More background can be found at
http://lwn.net/Articles/558104/"
* 'x86-fb-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fbdev: fbcon: select VT_HW_CONSOLE_BINDING
fbdev: efifb: bind to efi-framebuffer
fbdev: vesafb: bind to platform-framebuffer device
fbdev: simplefb: add common x86 RGB formats
x86: sysfb: move EFI quirks from efifb to sysfb
x86: provide platform-devices for boot-framebuffers
fbdev: simplefb: mark as fw and allocate apertures
fbdev: simplefb: add init through platform_data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cpu feature fixes from Ingo Molnar:
"Two small cpufeature support updates"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix override new_cpu_data.x86 with 486
x86, cpufeature: Use new CC_HAVE_ASM_GOTO
|