| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The O2Micro controller only supports tuning at 4-bits. So the host driver
needs to change the bus width while tuning and then set it back when done.
There was a bug in the original implementation in that mmc->ios.bus_width
also wasn't updated. Thus setting the incorrect blocksize in
sdhci_send_tuning which results in a tuning failure.
Signed-off-by: Raul E Rangel <[email protected]>
Fixes: 0086fc217d5d7 ("mmc: sdhci: Add support for O2 hardware tuning")
Acked-by: Adrian Hunter <[email protected]>
Cc: [email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
When Broadcom SDIO cards are idled they go to sleep and a whole
separate subsystem takes over their SDIO communication. This is the
Always-On-Subsystem (AOS) and it can't handle tuning requests.
Specifically, as tested on rk3288-veyron-minnie (which reports having
BCM4354/1 in dmesg), if I force a retune in brcmf_sdio_kso_control()
when "on = 1" (aka we're transition from sleep to wake) by whacking:
bus->sdiodev->func1->card->host->need_retune = 1
...then I can often see tuning fail. In this case dw_mmc reports "All
phases bad!"). Note that I don't get 100% failure, presumably because
sometimes the card itself has already transitioned away from the AOS
itself by the time we try to wake it up. If I force retuning when "on
= 0" (AKA force retuning right before sending the command to go to
sleep) then retuning is always OK.
NOTE: we need _both_ this patch and the patch to avoid triggering
tuning due to CRC errors in the sleep/wake transition, AKA ("brcmfmac:
sdio: Disable auto-tuning around commands expected to fail"). Though
both patches handle issues with Broadcom's AOS, the problems are
distinct:
1. We want to defer (but not ignore) asynchronous (like
timer-requested) tuning requests till the card is awake. However,
we want to ignore CRC errors during the transition, we don't want
to queue deferred tuning request.
2. You could imagine that the AOS could implement retuning but we
could still get errors while transitioning in and out of the AOS.
Similarly you could imagine a seamless transition into and out of
the AOS (with no CRC errors) even if the AOS couldn't handle
tuning.
ALSO NOTE: presumably there is never a desperate need to retune in
order to wake up the card, since doing so is impossible. Luckily the
only way the card can get into sleep state is if we had a good enough
tuning to send it the command to put it into sleep, so presumably that
"good enough" tuning is enough to wake us up, at least with a few
retries.
Cc: [email protected] #v4.18+
Signed-off-by: Douglas Anderson <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Reviewed-by: Arend van Spriel <[email protected]>
Acked-by: Kalle Valo <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
We want SDIO drivers to be able to temporarily stop retuning when the
driver knows that the SDIO card is not in a state where retuning will
work (maybe because the card is asleep). We'll move the relevant
functions to a place where drivers can call them.
Cc: [email protected] #v4.18+
Signed-off-by: Douglas Anderson <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Acked-by: Kalle Valo <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
There are certain cases, notably when transitioning between sleep and
active state, when Broadcom SDIO WiFi cards will produce errors on the
SDIO bus. This is evident from the source code where you can see that
we try commands in a loop until we either get success or we've tried
too many times. The comment in the code reinforces this by saying
"just one write attempt may fail"
Unfortunately these failures sometimes end up causing an "-EILSEQ"
back to the core which triggers a retuning of the SDIO card and that
blocks all traffic to the card until it's done.
Let's disable retuning around the commands we expect might fail.
Cc: [email protected] #v4.18+
Signed-off-by: Douglas Anderson <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Reviewed-by: Arend van Spriel <[email protected]>
Acked-by: Kalle Valo <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Normally when the MMC core sees an "-EILSEQ" error returned by a host
controller then it will trigger a retuning of the card. This is
generally a good idea.
However, if a command is expected to sometimes cause transfer errors
then these transfer errors shouldn't cause a re-tuning. This
re-tuning will be a needless waste of time. One example case where a
transfer is expected to cause errors is when transitioning between
idle (sometimes referred to as "sleep" in Broadcom code) and active
state on certain Broadcom WiFi SDIO cards. Specifically if the card
was already transitioning between states when the command was sent it
could cause an error on the SDIO bus.
Let's add an API that the SDIO function drivers can call that will
temporarily disable the auto-tuning functionality. Then we can add a
call to this in the Broadcom WiFi driver and any other driver that
might have similar needs.
NOTE: this makes the assumption that the card is already tuned well
enough that it's OK to disable the auto-retuning during one of these
error-prone situations. Presumably the driver code performing the
error-prone transfer knows how to recover / retry from errors. ...and
after we can get back to a state where transfers are no longer
error-prone then we can enable the auto-retuning again. If we truly
find ourselves in a case where the card needs to be retuned sometimes
to handle one of these error-prone transfers then we can always try a
few transfers first without auto-retuning and then re-try with
auto-retuning if the first few fail.
Without this change on rk3288-veyron-minnie I periodically see this in
the logs of a machine just sitting there idle:
dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to XYZ
Cc: [email protected] #v4.18+
Signed-off-by: Douglas Anderson <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Acked-by: Kalle Valo <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
This reverts commit 29f6589140a10ece8c1d73f58043ea5b3473ab3e.
After that patch landed I find that my kernel log on
rk3288-veyron-minnie and rk3288-veyron-speedy is filled with:
brcmfmac: brcmf_sdio_bus_sleep: error while changing bus sleep state -110
This seems to happen every time the Broadcom WiFi transitions out of
sleep mode. Reverting the commit fixes the problem for me, so that's
what this patch does.
Note that, in general, the justification in the original commit seemed
a little weak. It looked like someone was testing on a SD card
controller that would sometimes die if there were CRC errors on the
bus. This used to happen back in early days of dw_mmc (the controller
on my boards), but we fixed it. Disabling a feature on all boards
just because one SD card controller is broken seems bad.
Fixes: 29f6589140a1 ("brcmfmac: disable command decode in sdio_aos")
Cc: Wright Feng <[email protected]>
Cc: Double Lo <[email protected]>
Cc: Madhan Mohan R <[email protected]>
Cc: Chi-Hsien Lin <[email protected]>
Signed-off-by: Douglas Anderson <[email protected]>
Cc: [email protected]
Acked-by: Kalle Valo <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Multiple ixp4xx specific files require macros from irqs.h that
were moved out from mach/irqs.h, e.g.:
arch/arm/mach-ixp4xx/vulcan-pci.c:41:19: error: this function declaration is not a prototype [-Werror,-Wstrict-prototypes]
arch/arm/mach-ixp4xx/vulcan-pci.c:49:10: error: implicit declaration of function 'IXP4XX_GPIO_IRQ' [-Werror,-Wimplicit-function-declaration]
return IXP4XX_GPIO_IRQ(INTA);
Include this header in all files that failed to build because of
that.
Fixes: dc8ef8cd3a05 ("ARM: ixp4xx: Convert to SPARSE_IRQ")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
Kbuild complains about ixp4xx_irq_setup not being __init
itself in some configurations:
WARNING: vmlinux.o(.text+0x85bae4): Section mismatch in reference from the function ixp4xx_irq_setup() to the function .init.text:set_handle_irq()
The function ixp4xx_irq_setup() references
the function __init set_handle_irq().
This is often because ixp4xx_irq_setup lacks a __init
annotation or the annotation of set_handle_irq is wrong.
I suspect it normally gets inlined, so we get no such warning,
but clang makes this obvious when the function is left out
of line.
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
Platforms should not normally select all the device drivers, leave that
up to the user and the defconfig file.
In this case, we get a warning for randconfig builds:
WARNING: unmet direct dependencies detected for SERIAL_OF_PLATFORM
Depends on [n]: TTY [=y] && HAS_IOMEM [=y] && SERIAL_8250 [=n] && OF [=y]
Selected by [y]:
- MACH_IXP4XX_OF [=y] && ARCH_IXP4XX [=y]
Fixes: 9540724ca29d ("ARM: ixp4xx: Add device tree boot support")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
The "+sec" extension is invalid for older ARM architectures, but
the code can now be built on any ARM configuration:
/tmp/trusted_foundations-2d0882.s: Assembler messages:
/tmp/trusted_foundations-2d0882.s:194: Error: architectural extension `sec' is not allowed for the current base architecture
/tmp/trusted_foundations-2d0882.s:201: Error: selected processor does not support `smc #0' in ARM mode
/tmp/trusted_foundations-2d0882.s:213: Error: architectural extension `sec' is not allowed for the current base architecture
/tmp/trusted_foundations-2d0882.s:220: Error: selected processor does not support `smc #0' in ARM mode
Add a dependency on ARMv7 for the build.
Fixes: 4cb5d9eca143 ("firmware: Move Trusted Foundations support")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
Setting params.phy_utmi_width in dwc2_lowlevel_hw_init() is pointless since
it's value will be overwritten by dwc2_init_params().
This change make sure to take in account the generic PHY width information
during paraminitialisation, done in dwc2_set_param_phy_utmi_width().
By doing so, the phy_utmi_width params can still be overrided by
devicetree specific params and will also be checked against hardware
capabilities.
Fixes: 707d80f0a3c5 ("usb: dwc2: gadget: Replace phyif with phy_utmi_width")
Acked-by: Minas Harutyunyan <[email protected]>
Tested-by: Marek Szyprowski <[email protected]>
Signed-off-by: Jules Maselbas <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
Add device tree probing to the fotg2 driver.
Signed-off-by: Hans Ulli Kroll <[email protected]>
[Drop DMA mask coercion, drivers/of/platform.c does the job]
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The wusb code takes a very peculiar approach at implementing CBC-MAC,
by using plain CBC into a scratch buffer, and taking the output IV
as the MAC.
We can clean up this code substantially by switching to the cbcmac
shash, as exposed by the CCM template. To ensure that the module is
loaded on demand, add the cbcmac template name as a module alias.
Signed-off-by: Ard Biesheuvel <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Recently usfbs gained availability to retrieve device speed, but there
is sill no way to determine the bus number or list of ports the device
is connected to when using usbfs. While this information can be obtained
from sysfs, not all environments allow sysfs access. In a jailed
environment a program might be simply given an opened file descriptor to
usbfs device, and it is really important that all data can be gathered
from said file descriptor.
This patch introduces a new ioctl, USBDEVFS_CONNINFO_EX, which return
extended connection information for the device, including the bus
number, address, port list and speed. The API allows kernel to extend
amount of data returned by the ioctl and userspace has an option of
adjusting the amount of data it is willing to consume. A new capability,
USBDEVFS_CAP_CONNINFO_EX, is introduced to help userspace in determining
whether the kernel supports this new ioctl.
Signed-off-by: Dmitry Torokhov <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Clang produces the following warning
drivers/usb/host/xhci-tegra.c:357:27: warning: unused variable
'mbox_cmd_name' [-Wunused-const-variable]
static const char * const mbox_cmd_name[] = {
Looks like it was intended for logging or debugging, but was
never implemented. Removing mbox_cmd_name.
Cc: [email protected]
Link: https://github.com/ClangBuiltLinux/linux/issues/533
Signed-off-by: Nathan Huckleberry <[email protected]>
Acked-by: Thierry Reding <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Existing code would mistakenly return success in case of error instead
of a proper return value.
Fixes: e9c6c5373088 ("RDMA/efa: Add common command handlers")
Reviewed-by: Firas JahJah <[email protected]>
Reviewed-by: Yossi Leybovich <[email protected]>
Signed-off-by: Gal Pressman <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
The call to sc_buffer_alloc currently returns NULL (no buffer) or
a buffer descriptor.
There is a third case when the port is down. Currently that
returns NULL and this prevents the caller from properly handling the
sc_buffer_alloc() failure. A verbs code link test after the call is
racy so the indication needs to come from the state check inside the allocation
routine to be valid.
Fix by encoding the ECOMM failure like SDMA. IS_ERR_OR_NULL() tests
are added at all call sites. For verbs send, this needs to treat any
error by returning a completion without any MMIO copy.
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
Once a send context is taken down due to a link failure, any QPs waiting
for pio credits will stay on the waitlist indefinitely.
Fix by wakeing up all QPs linked to piowait list.
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
Once an SDMA engine is taken down due to a link failure, any waiting QPs
that do not have outstanding descriptors in the ring will stay
on the dmawait list as long as the port is down.
Since there is no timer running, they will stay there for a long time.
The fix is to wake up all iowaits linked to dmawait. The send engine
will build and post packets that get flushed back.
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Kaike Wan <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
SDMA and pio flushes will cause a lot of packets to be transmitted
after a link has gone down, using a lot of CPU to retransmit
packets.
Fix for RC QPs by recognizing the flush status and:
- Forcing a timer start
- Putting the QP into a "send one" mode
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Kaike Wan <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
This paves the way for another patch that reacts to a
flush sdma completion for RC.
Fixes: 81cd3891f021 ("IB/hfi1: Add support for 16B Management Packets")
Reviewed-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
The following warning can happen when a memory shortage
occurs during txreq allocation:
[10220.939246] SLUB: Unable to allocate memory on node -1, gfp=0xa20(GFP_ATOMIC)
[10220.939246] Hardware name: Intel Corporation S2600WT2R/S2600WT2R, BIOS SE5C610.86B.01.01.0018.C4.072020161249 07/20/2016
[10220.939247] cache: mnt_cache, object size: 384, buffer size: 384, default order: 2, min order: 0
[10220.939260] Workqueue: hfi0_0 _hfi1_do_send [hfi1]
[10220.939261] node 0: slabs: 1026568, objs: 43115856, free: 0
[10220.939262] Call Trace:
[10220.939262] node 1: slabs: 820872, objs: 34476624, free: 0
[10220.939263] dump_stack+0x5a/0x73
[10220.939265] warn_alloc+0x103/0x190
[10220.939267] ? wake_all_kswapds+0x54/0x8b
[10220.939268] __alloc_pages_slowpath+0x86c/0xa2e
[10220.939270] ? __alloc_pages_nodemask+0x2fe/0x320
[10220.939271] __alloc_pages_nodemask+0x2fe/0x320
[10220.939273] new_slab+0x475/0x550
[10220.939275] ___slab_alloc+0x36c/0x520
[10220.939287] ? hfi1_make_rc_req+0x90/0x18b0 [hfi1]
[10220.939299] ? __get_txreq+0x54/0x160 [hfi1]
[10220.939310] ? hfi1_make_rc_req+0x90/0x18b0 [hfi1]
[10220.939312] __slab_alloc+0x40/0x61
[10220.939323] ? hfi1_make_rc_req+0x90/0x18b0 [hfi1]
[10220.939325] kmem_cache_alloc+0x181/0x1b0
[10220.939336] hfi1_make_rc_req+0x90/0x18b0 [hfi1]
[10220.939348] ? hfi1_verbs_send_dma+0x386/0xa10 [hfi1]
[10220.939359] ? find_prev_entry+0xb0/0xb0 [hfi1]
[10220.939371] hfi1_do_send+0x1d9/0x3f0 [hfi1]
[10220.939372] process_one_work+0x171/0x380
[10220.939374] worker_thread+0x49/0x3f0
[10220.939375] kthread+0xf8/0x130
[10220.939377] ? max_active_store+0x80/0x80
[10220.939378] ? kthread_bind+0x10/0x10
[10220.939379] ret_from_fork+0x35/0x40
[10220.939381] SLUB: Unable to allocate memory on node -1, gfp=0xa20(GFP_ATOMIC)
The shortage is handled properly so the message isn't needed. Silence by
adding the no warn option to the slab allocation.
Fixes: 45842abbb292 ("staging/rdma/hfi1: move txreq header code")
Cc: <[email protected]>
Reviewed-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
Heavy contention of the sde flushlist_lock can cause hard lockups at
extreme scale when the flushing logic is under stress.
Mitigate by replacing the item at a time copy to the local list with
an O(1) list_splice_init() and using the high priority work queue to
do the flushes.
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Cc: <[email protected]>
Reviewed-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
The hcall H_SET_DAWR is used by a guest to set the data address
watchpoint register (DAWR). This hcall is handled in the host in
kvmppc_h_set_dawr() which can be called in either real mode on the
guest exit path from hcall_try_real_mode() in book3s_hv_rmhandlers.S,
or in virtual mode when called from kvmppc_pseries_do_hcall() in
book3s_hv.c.
The function kvmppc_h_set_dawr() updates the dawr and dawrx fields in
the vcpu struct accordingly and then also writes the respective values
into the DAWR and DAWRX registers directly. It is necessary to write
the registers directly here when calling the function in real mode
since the path to re-enter the guest won't do this. However when in
virtual mode the host DAWR and DAWRX values have already been
restored, and so writing the registers would overwrite these.
Additionally there is no reason to write the guest values here as
these will be read from the vcpu struct and written to the registers
appropriately the next time the vcpu is run.
This also avoids the case when handling h_set_dawr for a nested guest
where the guest hypervisor isn't able to write the DAWR and DAWRX
registers directly and must rely on the real hypervisor to do this for
it when it calls H_ENTER_NESTED.
Fixes: c1fe190c0672 ("powerpc: Add force enable of DAWR on P9 option")
Signed-off-by: Suraj Jitindar Singh <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
Commit c1fe190c0672 ("powerpc: Add force enable of DAWR on P9 option")
screwed up some assembler and corrupted a pointer in r3. This resulted
in crashes like the below:
BUG: Kernel NULL pointer dereference at 0x000013bf
Faulting instruction address: 0xc00000000010b044
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
CPU: 8 PID: 1771 Comm: qemu-system-ppc Kdump: loaded Not tainted 5.2.0-rc4+ #3
NIP: c00000000010b044 LR: c0080000089dacf4 CTR: c00000000010aff4
REGS: c00000179b397710 TRAP: 0300 Not tainted (5.2.0-rc4+)
MSR: 800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 42244842 XER: 00000000
CFAR: c00000000010aff8 DAR: 00000000000013bf DSISR: 42000000 IRQMASK: 0
GPR00: c0080000089dd6bc c00000179b3979a0 c008000008a04300 ffffffffffffffff
GPR04: 0000000000000000 0000000000000003 000000002444b05d c0000017f11c45d0
...
NIP kvmppc_h_set_dabr+0x50/0x68
LR kvmppc_pseries_do_hcall+0xa3c/0xeb0 [kvm_hv]
Call Trace:
0xc0000017f11c0000 (unreliable)
kvmppc_vcpu_run_hv+0x694/0xec0 [kvm_hv]
kvmppc_vcpu_run+0x34/0x48 [kvm]
kvm_arch_vcpu_ioctl_run+0x2f4/0x400 [kvm]
kvm_vcpu_ioctl+0x460/0x850 [kvm]
do_vfs_ioctl+0xe4/0xb40
ksys_ioctl+0xc4/0x110
sys_ioctl+0x28/0x80
system_call+0x5c/0x70
Instruction dump:
4082fff4 4c00012c 38600000 4e800020 e96280c0 896b0000 2c2b0000 3860ffff
4d820020 50852e74 508516f6 78840724 <f88313c0> f8a313c8 7c942ba6 7cbc2ba6
Fix the bug by only changing r3 when we are returning immediately.
Fixes: c1fe190c0672 ("powerpc: Add force enable of DAWR on P9 option")
Signed-off-by: Michael Neuling <[email protected]>
Signed-off-by: Suraj Jitindar Singh <[email protected]>
Reported-by: Cédric Le Goater <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
Pull vfs fixes from Al Viro:
"MS_MOVE regression fix + breakage in fsmount(2) (also introduced in
this cycle, along with fsmount(2) itself).
I'm still digging through the piles of mail, so there might be more
fixes to follow, but these two are obvious and self-contained, so
there's no point delaying those..."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs/namespace: fix unprivileged mount propagation
vfs: fsmount: add missing mntget()
|
|
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
|
|
When propagating mounts across mount namespaces owned by different user
namespaces it is not possible anymore to move or umount the mount in the
less privileged mount namespace.
Here is a reproducer:
sudo mount -t tmpfs tmpfs /mnt
sudo --make-rshared /mnt
# create unprivileged user + mount namespace and preserve propagation
unshare -U -m --map-root --propagation=unchanged
# now change back to the original mount namespace in another terminal:
sudo mkdir /mnt/aaa
sudo mount -t tmpfs tmpfs /mnt/aaa
# now in the unprivileged user + mount namespace
mount --move /mnt/aaa /opt
Unfortunately, this is a pretty big deal for userspace since this is
e.g. used to inject mounts into running unprivileged containers.
So this regression really needs to go away rather quickly.
The problem is that a recent change falsely locked the root of the newly
added mounts by setting MNT_LOCKED. Fix this by only locking the mounts
on copy_mnt_ns() and not when adding a new mount.
Fixes: 3bd045cc9c4b ("separate copying and locking mount tree on cross-userns copies")
Cc: Linus Torvalds <[email protected]>
Cc: Al Viro <[email protected]>
Cc: <[email protected]>
Tested-by: Christian Brauner <[email protected]>
Acked-by: Christian Brauner <[email protected]>
Signed-off-by: "Eric W. Biederman" <[email protected]>
Signed-off-by: Christian Brauner <[email protected]>
Signed-off-by: Al Viro <[email protected]>
|
|
sys_fsmount() needs to take a reference to the new mount when adding it
to the anonymous mount namespace. Otherwise the filesystem can be
unmounted while it's still in use, as found by syzkaller.
Reported-by: Mark Rutland <[email protected]>
Reported-by: [email protected]
Reported-by: [email protected]
Fixes: 93766fbd2696 ("vfs: syscall: Add fsmount() to create a mount for a superblock")
Signed-off-by: Eric Biggers <[email protected]>
Signed-off-by: Al Viro <[email protected]>
|
|
We can not hold the GlobalMid_Lock spinlock during the
dfs processing in cifs_reconnect since it invokes things that may sleep
and thus trigger :
BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:23
Thus we need to drop the spinlock during this code block.
RHBZ: 1716743
Cc: [email protected]
Signed-off-by: Ronnie Sahlberg <[email protected]>
Acked-by: Pavel Shilovsky <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
Some servers such as Windows 10 will return STATUS_INSUFFICIENT_RESOURCES
as the number of simultaneous SMB3 requests grows (even though the client
has sufficient credits). Return EAGAIN on STATUS_INSUFFICIENT_RESOURCES
so that we can retry writes which fail with this status code.
This (for example) fixes large file copies to Windows 10 on fast networks.
Signed-off-by: Steve French <[email protected]>
CC: Stable <[email protected]>
Reviewed-by: Ronnie Sahlberg <[email protected]>
Reviewed-by: Pavel Shilovsky <[email protected]>
|
|
A branch is needed here to get the fix into staging-next as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
There are some backward incompatible features pending
for months, mainly due to on-disk format expensions.
However, we should ensure that it cannot be mounted with
old kernels. Otherwise, it will causes unexpected behaviors.
Fixes: ba2b77a82022 ("staging: erofs: add super block operations")
Cc: <[email protected]> # 4.19+
Reviewed-by: Chao Yu <[email protected]>
Signed-off-by: Gao Xiang <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 5.2 cycle.
* ad7150
- sense of bit for controlling adaptive vs fixed threshold was flipped.
* adt7316
- Fix a build issue due to wrong headers for gpio usage.
* lsm6dsx
- correctly suspend / resume i2c slaves when the host goes to sleep.
* mlx90632
- relax a compatability check to allow for newer devices.
Also one counters fix
* counter/ftm-quaddec
- missing dependencies in Kconfig.
* tag 'iio-fixes-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
counter/ftm-quaddec: Add missing dependencies in Kconfig
staging: iio: adt7316: Fix build errors when GPIOLIB is not set
iio: temperature: mlx90632 Relax the compatibility check
iio: imu: st_lsm6dsx: fix PM support for st_lsm6dsx i2c controller
staging:iio:ad7150: fix threshold mode config bit
|
|
Eric Dumazet says:
====================
tcp: make sack processing more robust
Jonathan Looney brought to our attention multiple problems
in TCP stack at the sender side.
SACK processing can be abused by malicious peers to either
cause overflows, or increase of memory usage.
First two patches fix the immediate problems.
Since the malicious peers abuse senders by advertizing a very
small MSS in their SYN or SYNACK packet, the last two
patches add a new sysctl so that admins can chose a higher
limit for MSS clamping.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix ssbd.c which depends implicitly on asm/ptrace.h including
linux/prctl.h (through for example linux/compat.h, then linux/time.h,
linux/seqlock.h, linux/spinlock.h and linux/irqflags.h), and uses
PR_SPEC* defines.
This is an issue since we'll soon be removing the include from
asm/ptrace.h.
Fixes: 9cdc0108baa8 ("arm64: ssbd: Add prctl interface for per-thread mitigation")
Cc: [email protected]
Signed-off-by: Anisse Astier <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"This contains fixes, defconfig, and DT data changes for the v5.2-rc
series.
The fixes are relatively straightforward:
- Addition of a TLB fence in the vmalloc_fault path, so the CPU
doesn't enter an infinite page fault loop
- Readdition of the pm_power_off export, so device drivers that
reassign it can now be built as modules
- A udelay() fix for RV32, fixing a miscomputation of the delay time
- Removal of deprecated smp_mb__*() barriers
This also adds initial DT data infrastructure for arch/riscv, along
with initial data for the SiFive FU540-C000 SoC and the corresponding
HiFive Unleashed board.
We also update the RV64 defconfig to include some core drivers for the
FU540 in the build"
* tag 'riscv-for-v5.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: remove unused barrier defines
riscv: mm: synchronize MMU after pte change
riscv: dts: add initial board data for the SiFive HiFive Unleashed
riscv: dts: add initial support for the SiFive FU540-C000 SoC
dt-bindings: riscv: convert cpu binding to json-schema
dt-bindings: riscv: sifive: add YAML documentation for the SiFive FU540
arch: riscv: add support for building DTB files from DT source data
riscv: Fix udelay in RV32.
riscv: export pm_power_off again
RISC-V: defconfig: enable clocks, serial console
|
|
When multiple iovecs reference the same page, each get_user_page call
will add a reference to the page. But once we've created the bio that
information gets lost and only a single reference will be dropped after
I/O completion. Use the same_page information returned from
__bio_try_merge_page to drop additional references to pages that were
already present in the bio.
Based on a patch from Ming Lei.
Link: https://lkml.org/lkml/2019/4/23/64
Fixes: 576ed913 ("block: use bio_add_page in bio_iov_iter_get_pages")
Reported-by: David Gibson <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
Reviewed-by: Ming Lei <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
We currently have an input same_page parameter to __bio_try_merge_page
to prohibit merging in the same page. The rationale for that is that
some callers need to account for every page added to a bio. Instead of
letting these callers call twice into the merge code to account for the
new vs existing page cases, just turn the paramter into an output one that
returns if a merge in the same page occured and let them act accordingly.
Signed-off-by: Christoph Hellwig <[email protected]>
Reviewed-by: Ming Lei <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
After the recent series of cleanups in the properties and xattrs modules
that landed in the 5.2 merge window, we ended up with a regression where
after deleting the compression xattr property through the setflags ioctl,
we don't set the BTRFS_INODE_COPY_EVERYTHING flag in the inode anymore.
As a consequence, if the inode was fsync'ed when it had the compression
property set, after deleting the compression property through the setflags
ioctl and fsync'ing again the inode, the log will still contain the
compression xattr, because the inode did not had that bit set, which
made the fsync not delete all xattrs from the log and copy all xattrs
from the subvolume tree to the log tree.
This regression happens due to the fact that that series of cleanups
made btrfs_set_prop() call the old function do_setxattr() (which is now
named btrfs_setxattr()), and not the old version of btrfs_setxattr(),
which is now called btrfs_setxattr_trans().
Fix this by setting the BTRFS_INODE_COPY_EVERYTHING bit in the current
btrfs_setxattr() function and remove it from everywhere else, including
its setup at btrfs_ioctl_setflags(). This is cleaner, avoids similar
regressions in the future, and centralizes the setup of the bit. After
all, the need to setup this bit should only be in the xattrs module,
since it is an implementation of xattrs.
Fixes: 04e6863b19c722 ("btrfs: split btrfs_setxattr calls regarding transaction")
CC: [email protected] # 4.4+
Signed-off-by: Filipe Manana <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
They were introduced in commit fab957c11efe ("RISC-V: Atomic and
Locking Code") long after commit 2e39465abc4b ("locking: Remove
deprecated smp_mb__() barriers") removed the remnants of all previous
instances from the tree.
Signed-off-by: Rolf Eike Beer <[email protected]>
[[email protected]: stripped spurious mbox header from patch
description; fixed commit references in patch header]
Signed-off-by: Paul Walmsley <[email protected]>
|
|
An endpoint conflict occurs when the USB is working in device mode
during an isochronous communication. When the endpointA IN direction
is an isochronous IN endpoint, and the host sends an IN token to
endpointA on another device, then the OUT transaction may be missed
regardless the OUT endpoint number. Generally, this occurs when the
device is connected to the host through a hub and other devices are
connected to the same hub.
The affected OUT endpoint can be either control, bulk, isochronous, or
an interrupt endpoint. After the OUT endpoint is primed, if an IN token
to the same endpoint number on another device is received, then the OUT
endpoint may be unprimed (cannot be detected by software), which causes
this endpoint to no longer respond to the host OUT token, and thus, no
corresponding interrupt occurs.
There is no good workaround for this issue, the only thing the software
could do is numbering isochronous IN from the highest endpoint since we
have observed most of device number endpoint from the lowest.
Cc: <[email protected]> #v3.14+
Cc: Fabio Estevam <[email protected]>
Cc: Greg KH <[email protected]>
Cc: Sergei Shtylyov <[email protected]>
Cc: Jun Li <[email protected]>
Signed-off-by: Peter Chen <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch updates the Qualcomm SoC repo to a new location.
Signed-off-by: Andy Gross <[email protected]>
Reviewed-by: Bjorn Andersson <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
If cmd19 timeout or response crcerr occurs during execute_tuning(),
it need invoke msdc_reset_hw(). Otherwise SDIO IRQ can't be detected.
Signed-off-by: jjian zhou <[email protected]>
Signed-off-by: Chaotian Jing <[email protected]>
Signed-off-by: Yong Mao <[email protected]>
Fixes: 5215b2e952f3 ("mmc: mediatek: Add MMC_CAP_SDIO_IRQ support")
Cc: [email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
SDIO IRQ is triggered by low level. It need disable SDIO IRQ
detected function. Otherwise the interrupt register can't be cleared.
It will process the interrupt more.
Signed-off-by: Jjian Zhou <[email protected]>
Signed-off-by: Chaotian Jing <[email protected]>
Signed-off-by: Yong Mao <[email protected]>
Fixes: 5215b2e952f3 ("mmc: mediatek: Add MMC_CAP_SDIO_IRQ support")
Cc: [email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
We don't have a reproducible error case, yet our BSP team suggested that
the mmc_switch_status() command in mmc_select_hs400() should come after
the callback into the driver completing HS400 setup. It makes sense to
me because we want the status of a fully setup HS400, so it will
increase the reliability of the mmc_switch_status() command.
Reported-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
Fixes: ba6c7ac3a2f4 ("mmc: core: more fine-grained hooks for HS400 tuning")
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Because RISC-V compliant implementations can cache invalid entries
in TLB, an SFENCE.VMA is necessary after changes to the page table.
This patch adds an SFENCE.vma for the vmalloc_fault path.
Signed-off-by: ShihPo Hung <[email protected]>
[[email protected]: reversed tab->whitespace conversion,
wrapped comment lines]
Signed-off-by: Paul Walmsley <[email protected]>
Cc: Palmer Dabbelt <[email protected]>
Cc: Albert Ou <[email protected]>
Cc: Paul Walmsley <[email protected]>
Cc: [email protected]
Cc: [email protected]
|
|
My @arm.com address will stop working at the end of August, so update to
my @kernel.org address where you'll still be able to reach me.
When I say "stop working" I really mean "will go to my line manager", so
send patches there at your peril because they may reply with roadmaps
and spreadsheets. You have been warned.
Cc: Will Deacon <[email protected]>
Cc: Catalin Marinas <[email protected]>
Cc: Marc Zyngier <[email protected]>
Cc: Russell King <[email protected]>
Cc: "Paul E . McKenney" <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Bjorn Helgaas <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: Stephen Rothwell <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Joerg Roedel <[email protected]>
Cc: arm-soc <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|