aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2021-08-10PCI/MSI: Mask all unused MSI-X entriesThomas Gleixner1-18/+27
When MSI-X is enabled the ordering of calls is: msix_map_region(); msix_setup_entries(); pci_msi_setup_msi_irqs(); msix_program_entries(); This has a few interesting issues: 1) msix_setup_entries() allocates the MSI descriptors and initializes them except for the msi_desc:masked member which is left zero initialized. 2) pci_msi_setup_msi_irqs() allocates the interrupt descriptors and sets up the MSI interrupts which ends up in pci_write_msi_msg() unless the interrupt chip provides its own irq_write_msi_msg() function. 3) msix_program_entries() does not do what the name suggests. It solely updates the entries array (if not NULL) and initializes the masked member for each MSI descriptor by reading the hardware state and then masks the entry. Obviously this has some issues: 1) The uninitialized masked member of msi_desc prevents the enforcement of masking the entry in pci_write_msi_msg() depending on the cached masked bit. Aside of that half initialized data is a NONO in general 2) msix_program_entries() only ensures that the actually allocated entries are masked. This is wrong as experimentation with crash testing and crash kernel kexec has shown. This limited testing unearthed that when the production kernel had more entries in use and unmasked when it crashed and the crash kernel allocated a smaller amount of entries, then a full scan of all entries found unmasked entries which were in use in the production kernel. This is obviously a device or emulation issue as the device reset should mask all MSI-X table entries, but obviously that's just part of the paper specification. Cure this by: 1) Masking all table entries in hardware 2) Initializing msi_desc::masked in msix_setup_entries() 3) Removing the mask dance in msix_program_entries() 4) Renaming msix_program_entries() to msix_update_entries() to reflect the purpose of that function. As the masking of unused entries has never been done the Fixes tag refers to a commit in: git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support") Signed-off-by: Thomas Gleixner <[email protected]> Tested-by: Marc Zyngier <[email protected]> Reviewed-by: Marc Zyngier <[email protected]> Acked-by: Bjorn Helgaas <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/r/[email protected]
2021-08-10PCI/MSI: Enable and mask MSI-X earlyThomas Gleixner1-13/+15
The ordering of MSI-X enable in hardware is dysfunctional: 1) MSI-X is disabled in the control register 2) Various setup functions 3) pci_msi_setup_msi_irqs() is invoked which ends up accessing the MSI-X table entries 4) MSI-X is enabled and masked in the control register with the comment that enabling is required for some hardware to access the MSI-X table Step #4 obviously contradicts #3. The history of this is an issue with the NIU hardware. When #4 was introduced the table access actually happened in msix_program_entries() which was invoked after enabling and masking MSI-X. This was changed in commit d71d6432e105 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts") which removed the table write from msix_program_entries(). Interestingly enough nobody noticed and either NIU still works or it did not get any testing with a kernel 3.19 or later. Nevertheless this is inconsistent and there is no reason why MSI-X can't be enabled and masked in the control register early on, i.e. move step #4 above to step #1. This preserves the NIU workaround and has no side effects on other hardware. Fixes: d71d6432e105 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts") Signed-off-by: Thomas Gleixner <[email protected]> Tested-by: Marc Zyngier <[email protected]> Reviewed-by: Ashok Raj <[email protected]> Reviewed-by: Marc Zyngier <[email protected]> Acked-by: Bjorn Helgaas <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/r/[email protected]
2021-08-10Merge branch 'ks8795-vlan-fixes'David S. Miller3-21/+74
Ben Hutchings says: ==================== ksz8795 VLAN fixes This series fixes a number of bugs in the ksz8795 driver that affect VLAN filtering, tag insertion, and tag removal. I've tested these on the KSZ8795CLXD evaluation board, and checked the register usage against the datasheets for the other supported chips. ==================== Signed-off-by: David S. Miller <[email protected]>
2021-08-10net: dsa: microchip: ksz8795: Don't use phy_port_cnt in VLAN table lookupBen Hutchings1-4/+4
The magic number 4 in VLAN table lookup was the number of entries we can read and write at once. Using phy_port_cnt here doesn't make sense and presumably broke VLAN filtering for 3-port switches. Change it back to 4. Fixes: 4ce2a984abd8 ("net: dsa: microchip: ksz8795: use phy_port_cnt ...") Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-08-10net: dsa: microchip: ksz8795: Fix VLAN filteringBen Hutchings1-0/+11
Currently ksz8_port_vlan_filtering() sets or clears the VLAN Enable hardware flag. That controls discarding of packets with a VID that has not been enabled for any port on the switch. Since it is a global flag, set the dsa_switch::vlan_filtering_is_global flag so that the DSA core understands this can't be controlled per port. When VLAN filtering is enabled, the switch should also discard packets with a VID that's not enabled on the ingress port. Set or clear each external port's VLAN Ingress Filter flag in ksz8_port_vlan_filtering() to make that happen. Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-08-10net: dsa: microchip: ksz8795: Use software untagging on CPU portBen Hutchings1-1/+8
On the CPU port, we can support both tagged and untagged VLANs at the same time by doing any necessary untagging in software rather than hardware. To enable that, keep the CPU port's Remove Tag flag cleared and set the dsa_switch::untag_bridge_pvid flag. Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-08-10net: dsa: microchip: ksz8795: Fix VLAN untagged flag change on deletionBen Hutchings1-3/+0
When a VLAN is deleted from a port, the flags in struct switchdev_obj_port_vlan are always 0. ksz8_port_vlan_del() copies the BRIDGE_VLAN_INFO_UNTAGGED flag to the port's Tag Removal flag, and therefore always clears it. In case there are multiple VLANs configured as untagged on this port - which seems useless, but is allowed - deleting one of them changes the remaining VLANs to be tagged. It's only ever necessary to change this flag when a VLAN is added to the port, so leave it unchanged in ksz8_port_vlan_del(). Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-08-10net: dsa: microchip: ksz8795: Reject unsupported VLAN configurationBen Hutchings2-1/+27
The switches supported by ksz8795 only have a per-port flag for Tag Removal. This means it is not possible to support both tagged and untagged VLANs on the same port. Reject attempts to add a VLAN that requires the flag to be changed, unless there are no VLANs currently configured. VID 0 is excluded from this check since it is untagged regardless of the state of the flag. On the CPU port we could support tagged and untagged VLANs at the same time. This will be enabled by a later patch. Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-08-10net: dsa: microchip: ksz8795: Fix PVID tag insertionBen Hutchings2-7/+23
ksz8795 has never actually enabled PVID tag insertion, and it also programmed the PVID incorrectly. To fix this: * Allow tag insertion to be controlled per ingress port. On most chips, set bit 2 in Global Control 19. On KSZ88x3 this control flag doesn't exist. * When adding a PVID: - Set the appropriate register bits to enable tag insertion on egress at every other port if this was the packet's ingress port. - Mask *out* the VID from the default tag, before or-ing in the new PVID. * When removing a PVID: - Clear the same control bits to disable tag insertion. - Don't update the default tag. This wasn't doing anything useful. Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-08-10net: dsa: microchip: Fix ksz_read64()Ben Hutchings1-6/+2
ksz_read64() currently does some dubious byte-swapping on the two halves of a 64-bit register, and then only returns the high bits. Replace this with a straightforward expression. Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-08-10Merge tag 'linux-can-fixes-for-5.14-20210810' of ↵David S. Miller2-5/+5
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can linux-can-fixes-for-5.14-20210810 Marc Kleine-Budde says: ==================== pull-request: can 2021-08-10 this is a pull request of 2 patches for net/master. Baruch Siach's patch fixes a typo for the Microchip CAN BUS Analyzer Tool entry in the MAINTAINERS file. Hussein Alasadi fixes the setting of the M_CAN_DBTP register in the m_can driver. The regression git mainline in v5.14-rc1, so no backport to stable is needed. ==================== Signed-off-by: David S. Miller <[email protected]>
2021-08-10Merge tag 'mlx5-fixes-2021-08-09' of ↵David S. Miller19-58/+83
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5 fixes 2021-08-09 This series introduces fixes to mlx5 driver. Please pull and let me know if there is any problem. ==================== Signed-off-by: David S. Miller <[email protected]>
2021-08-10Merge branch '100GbE' of ↵David S. Miller4-13/+36
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-08-09 This series contains updates to ice and iavf drivers. Ani prevents the ice driver from accidentally being probed to a virtual function and stops processing of VF messages when VFs are being torn down. Brett prevents the ice driver from deleting is own MAC address. Fahad ensures the RSS LUT and key are always set following reset for iavf. ==================== Signed-off-by: David S. Miller <[email protected]>
2021-08-10bpf: Fix potentially incorrect results with bpf_get_local_storage()Yonghong Song2-4/+4
Commit b910eaaaa4b8 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage() helper") fixed a bug for bpf_get_local_storage() helper so different tasks won't mess up with each other's percpu local storage. The percpu data contains 8 slots so it can hold up to 8 contexts (same or different tasks), for 8 different program runs, at the same time. This in general is sufficient. But our internal testing showed the following warning multiple times: [...] warning: WARNING: CPU: 13 PID: 41661 at include/linux/bpf-cgroup.h:193 __cgroup_bpf_run_filter_sock_ops+0x13e/0x180 RIP: 0010:__cgroup_bpf_run_filter_sock_ops+0x13e/0x180 <IRQ> tcp_call_bpf.constprop.99+0x93/0xc0 tcp_conn_request+0x41e/0xa50 ? tcp_rcv_state_process+0x203/0xe00 tcp_rcv_state_process+0x203/0xe00 ? sk_filter_trim_cap+0xbc/0x210 ? tcp_v6_inbound_md5_hash.constprop.41+0x44/0x160 tcp_v6_do_rcv+0x181/0x3e0 tcp_v6_rcv+0xc65/0xcb0 ip6_protocol_deliver_rcu+0xbd/0x450 ip6_input_finish+0x11/0x20 ip6_input+0xb5/0xc0 ip6_sublist_rcv_finish+0x37/0x50 ip6_sublist_rcv+0x1dc/0x270 ipv6_list_rcv+0x113/0x140 __netif_receive_skb_list_core+0x1a0/0x210 netif_receive_skb_list_internal+0x186/0x2a0 gro_normal_list.part.170+0x19/0x40 napi_complete_done+0x65/0x150 mlx5e_napi_poll+0x1ae/0x680 __napi_poll+0x25/0x120 net_rx_action+0x11e/0x280 __do_softirq+0xbb/0x271 irq_exit_rcu+0x97/0xa0 common_interrupt+0x7f/0xa0 </IRQ> asm_common_interrupt+0x1e/0x40 RIP: 0010:bpf_prog_1835a9241238291a_tw_egress+0x5/0xbac ? __cgroup_bpf_run_filter_skb+0x378/0x4e0 ? do_softirq+0x34/0x70 ? ip6_finish_output2+0x266/0x590 ? ip6_finish_output+0x66/0xa0 ? ip6_output+0x6c/0x130 ? ip6_xmit+0x279/0x550 ? ip6_dst_check+0x61/0xd0 [...] Using drgn [0] to dump the percpu buffer contents showed that on this CPU slot 0 is still available, but slots 1-7 are occupied and those tasks in slots 1-7 mostly don't exist any more. So we might have issues in bpf_cgroup_storage_unset(). Further debugging confirmed that there is a bug in bpf_cgroup_storage_unset(). Currently, it tries to unset "current" slot with searching from the start. So the following sequence is possible: 1. A task is running and claims slot 0 2. Running BPF program is done, and it checked slot 0 has the "task" and ready to reset it to NULL (not yet). 3. An interrupt happens, another BPF program runs and it claims slot 1 with the *same* task. 4. The unset() in interrupt context releases slot 0 since it matches "task". 5. Interrupt is done, the task in process context reset slot 0. At the end, slot 1 is not reset and the same process can continue to occupy slots 2-7 and finally, when the above step 1-5 is repeated again, step 3 BPF program won't be able to claim an empty slot and a warning will be issued. To fix the issue, for unset() function, we should traverse from the last slot to the first. This way, the above issue can be avoided. The same reverse traversal should also be done in bpf_get_local_storage() helper itself. Otherwise, incorrect local storage may be returned to BPF program. [0] https://github.com/osandov/drgn Fixes: b910eaaaa4b8 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage() helper") Signed-off-by: Yonghong Song <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Andrii Nakryiko <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2021-08-10Merge tag 'efi-urgent-for-v5.14-rc4' of ↵Thomas Gleixner2-10/+63
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/urgent Pull EFI fixes from Ard Biesheuvel: A batch of fixes for the arm64 stub image loader: - fix a logic bug that can make the random page allocator fail spuriously - force reallocation of the Image when it overlaps with firmware reserved memory regions - fix an oversight that defeated on optimization introduced earlier where images loaded at a suitable offset are never moved if booting without randomization - complain about images that were not loaded at the right offset by the firmware image loader. Link: https://lore.kernel.org/r/[email protected]
2021-08-10ovl: prevent private clone if bind mount is not allowedMiklos Szeredi1-14/+28
Add the following checks from __do_loopback() to clone_private_mount() as well: - verify that the mount is in the current namespace - verify that there are no locked children Reported-by: Alois Wohlschlager <[email protected]> Fixes: c771d683a62e ("vfs: introduce clone_private_mount()") Cc: <[email protected]> # v3.18 Signed-off-by: Miklos Szeredi <[email protected]>
2021-08-10ovl: fix uninitialized pointer read in ovl_lookup_real_one()Miklos Szeredi1-1/+1
One error path can result in release_dentry_name_snapshot() being called before "name" was initialized by take_dentry_name_snapshot(). Fix by moving the release_dentry_name_snapshot() to immediately after the only use. Reported-by: Colin Ian King <[email protected]> Signed-off-by: Miklos Szeredi <[email protected]>
2021-08-10ovl: fix deadlock in splice writeMiklos Szeredi1-1/+46
There's possibility of an ABBA deadlock in case of a splice write to an overlayfs file and a concurrent splice write to a corresponding real file. The call chain for splice to an overlay file: -> do_splice [takes sb_writers on overlay file] -> do_splice_from -> iter_file_splice_write [takes pipe->mutex] -> vfs_iter_write ... -> ovl_write_iter [takes sb_writers on real file] And the call chain for splice to a real file: -> do_splice [takes sb_writers on real file] -> do_splice_from -> iter_file_splice_write [takes pipe->mutex] Syzbot successfully bisected this to commit 82a763e61e2b ("ovl: simplify file splice"). Fix by reverting the write part of the above commit and by adding missing bits from ovl_write_iter() into ovl_splice_write(). Fixes: 82a763e61e2b ("ovl: simplify file splice") Reported-and-tested-by: [email protected] Signed-off-by: Miklos Szeredi <[email protected]>
2021-08-10ovl: skip stale entries in merge dir cache iterationAmir Goldstein1-0/+5
On the first getdents call, ovl_iterate() populates the readdir cache with a list of entries, but for upper entries with origin lower inode, p->ino remains zero. Following getdents calls traverse the readdir cache list and call ovl_cache_update_ino() for entries with zero p->ino to lookup the entry in the overlay and return d_ino that is consistent with st_ino. If the upper file was unlinked between the first getdents call and the getdents call that lists the file entry, ovl_cache_update_ino() will not find the entry and fall back to setting d_ino to the upper real st_ino, which is inconsistent with how this object was presented to users. Instead of listing a stale entry with inconsistent d_ino, simply skip the stale entry, which is better for users. xfstest overlay/077 is failing without this patch. Signed-off-by: Amir Goldstein <[email protected]> Link: https://lore.kernel.org/fstests/CAOQ4uxgR_cLnC_vdU5=seP3fwqVkuZM_-WfD6maFTMbMYq=a9w@mail.gmail.com/ Signed-off-by: Miklos Szeredi <[email protected]>
2021-08-10bpf: Add missing bpf_read_[un]lock_trace() for syscall programYonghong Song1-0/+4
Commit 79a7f8bdb159d ("bpf: Introduce bpf_sys_bpf() helper and program type.") added support for syscall program, which is a sleepable program. But the program run missed bpf_read_lock_trace()/bpf_read_unlock_trace(), which is needed to ensure proper rcu callback invocations. This patch adds bpf_read_[un]lock_trace() properly. Fixes: 79a7f8bdb159d ("bpf: Introduce bpf_sys_bpf() helper and program type.") Signed-off-by: Yonghong Song <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Andrii Nakryiko <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2021-08-10bpf: Add lockdown check for probe_write_user helperDaniel Borkmann3-2/+5
Back then, commit 96ae52279594 ("bpf: Add bpf_probe_write_user BPF helper to be called in tracers") added the bpf_probe_write_user() helper in order to allow to override user space memory. Its original goal was to have a facility to "debug, divert, and manipulate execution of semi-cooperative processes" under CAP_SYS_ADMIN. Write to kernel was explicitly disallowed since it would otherwise tamper with its integrity. One use case was shown in cf9b1199de27 ("samples/bpf: Add test/example of using bpf_probe_write_user bpf helper") where the program DNATs traffic at the time of connect(2) syscall, meaning, it rewrites the arguments to a syscall while they're still in userspace, and before the syscall has a chance to copy the argument into kernel space. These days we have better mechanisms in BPF for achieving the same (e.g. for load-balancers), but without having to write to userspace memory. Of course the bpf_probe_write_user() helper can also be used to abuse many other things for both good or bad purpose. Outside of BPF, there is a similar mechanism for ptrace(2) such as PTRACE_PEEK{TEXT,DATA} and PTRACE_POKE{TEXT,DATA}, but would likely require some more effort. Commit 96ae52279594 explicitly dedicated the helper for experimentation purpose only. Thus, move the helper's availability behind a newly added LOCKDOWN_BPF_WRITE_USER lockdown knob so that the helper is disabled under the "integrity" mode. More fine-grained control can be implemented also from LSM side with this change. Fixes: 96ae52279594 ("bpf: Add bpf_probe_write_user BPF helper to be called in tracers") Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Andrii Nakryiko <[email protected]>
2021-08-10drm/meson: fix colour distortion from HDR set during vendor u-bootChristian Hewitt2-1/+11
Add support for the OSD1 HDR registers so meson DRM can handle the HDR properties set by Amlogic u-boot on G12A and newer devices which result in blue/green/pink colour distortion to display output. This takes the original patch submissions from Mathias [0] and [1] with corrections for formatting and the missing description and attribution needed for merge. [0] https://lore.kernel.org/linux-amlogic/[email protected]/T/ [1] https://lore.kernel.org/linux-amlogic/CAOKfEHBx_fboUqkENEMd-OC-NSrf46nto+vDLgvgttzPe99kXg@mail.gmail.com/T/#u Fixes: 728883948b0d ("drm/meson: Add G12A Support for VIU setup") Suggested-by: Mathias Steiger <[email protected]> Signed-off-by: Christian Hewitt <[email protected]> Tested-by: Neil Armstrong <[email protected]> Tested-by: Philip Milev <[email protected]> [narmsrong: adding missing space on second tested-by tag] Signed-off-by: Neil Armstrong <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2021-08-10Revert "usb: dwc3: gadget: Use list_replace_init() before traversing lists"Greg Kroah-Hartman1-16/+2
This reverts commit d25d85061bd856d6be221626605319154f9b5043 as it is reported to cause problems on many different types of boards. Reported-by: Thinh Nguyen <[email protected]> Reported-by: John Stultz <[email protected]> Cc: Ray Chi <[email protected]> Link: https://lore.kernel.org/r/CANcMJZCEVxVLyFgLwK98hqBEdc0_n4P0x_K6Gih8zNH3ouzbJQ@mail.gmail.com Fixes: d25d85061bd8 ("usb: dwc3: gadget: Use list_replace_init() before traversing lists") Cc: stable <[email protected]> Cc: Felipe Balbi <[email protected]> Cc: Wesley Cheng <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-08-10Merge tag 'iio-fixes-5.14a' of ↵Greg Kroah-Hartman7-49/+10
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus Jonathan writes: First set of fixes for IIO in the 5.14 cycle adi,adis: - Ensure GPIO pin direction set explicitly in driver. fxls8952af: - Fix use of ret when not initialized. - Fix issue with use of module symbol from built in. hdc100x: - Add a margin to conversion time as some parts run to slowly. palmas-adc: - Fix a wrong exit condition that leads to adc period always being set to maximum value. st,sensors: - Drop a wrong restriction on number of interrupts in dt binding. ti-ads7950: - Ensure CS deasserted after channel read. * tag 'iio-fixes-5.14a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: iio: adc: Fix incorrect exit of for-loop iio: humidity: hdc100x: Add margin to the conversion time dt-bindings: iio: st: Remove wrong items length check iio: accel: fxls8962af: fix i2c dependency iio: adis: set GPIO reset pin direction iio: adc: ti-ads7950: Ensure CS is deasserted after reading channels iio: accel: fxls8962af: fix potential use of uninitialized symbol
2021-08-10locking/rtmutex: Use the correct rtmutex debugging config optionZhen Lei1-1/+1
It's CONFIG_DEBUG_RT_MUTEXES not CONFIG_DEBUG_RT_MUTEX. Fixes: f7efc4799f81 ("locking/rtmutex: Inline chainwalk depth check") Signed-off-by: Zhen Lei <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Acked-by: Will Deacon <[email protected]> Acked-by: Boqun Feng <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/r/[email protected]
2021-08-10can: m_can: m_can_set_bittiming(): fix setting M_CAN_DBTP registerHussein Alasadi1-4/+4
This patch fixes the setting of the M_CAN_DBTP register contents: - use DBTP_ (the data bitrate macros) instead of NBTP_ which area used for the nominal bitrate - do not overwrite possibly-existing DBTP_TDC flag by ORing reg_btp instead of overwriting Link: https://lore.kernel.org/r/FRYP281MB06140984ABD9994C0AAF7433D1F69@FRYP281MB0614.DEUP281.PROD.OUTLOOK.COM Fixes: 20779943a080 ("can: m_can: use bits.h macros for all regmasks") Cc: Torin Cooper-Bennun <[email protected]> Cc: Chandrasekar Ramakrishnan <[email protected]> Signed-off-by: Hussein Alasadi <[email protected]> [mkl: update patch description, update indention] Signed-off-by: Marc Kleine-Budde <[email protected]>
2021-08-10MAINTAINERS: fix Microchip CAN BUS Analyzer Tool entry typoBaruch Siach1-1/+1
This patch fixes the abbreviated name of the Microchip CAN BUS Analyzer Tool. Fixes: 8a7b46fa7902 ("MAINTAINERS: add Yasushi SHOJI as reviewer for the Microchip CAN BUS Analyzer Tool driver") Link: https://lore.kernel.org/r/cc4831cb1c8759c15fb32c21fd326e831183733d.1627876781.git.baruch@tkos.co.il Signed-off-by: Baruch Siach <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2021-08-09net/mlx5: Fix return value from tracer initializationAya Levin1-2/+9
Check return value of mlx5_fw_tracer_start(), set error path and fix return value of mlx5_fw_tracer_init() accordingly. Fixes: c71ad41ccb0c ("net/mlx5: FW tracer, events handling") Signed-off-by: Aya Levin <[email protected]> Reviewed-by: Moshe Shemesh <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09net/mlx5: Synchronize correct IRQ when destroying CQShay Drory10-30/+27
The CQ destroy is performed based on the IRQ number that is stored in cq->irqn. That number wasn't set explicitly during CQ creation and as expected some of the API users of mlx5_core_create_cq() forgot to update it. This caused to wrong synchronization call of the wrong IRQ with a number 0 instead of the real one. As a fix, set the IRQ number directly in the mlx5_core_create_cq() and update all users accordingly. Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices") Fixes: ef1659ade359 ("IB/mlx5: Add DEVX support for CQ events") Signed-off-by: Shay Drory <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09net/mlx5e: TC, Fix error handling memory leakChris Mi1-0/+1
Free the offload sample action on error. Fixes: f94d6389f6a8 ("net/mlx5e: TC, Add support to offload sample action") Signed-off-by: Chris Mi <[email protected]> Reviewed-by: Oz Shlomo <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09net/mlx5: Destroy pool->mutexShay Drory1-1/+2
Destroy pool->mutex when we destroy the pool. Fixes: c36326d38d93 ("net/mlx5: Round-Robin EQs over IRQs") Signed-off-by: Shay Drory <[email protected]> Reviewed-by: Parav Pandit <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09net/mlx5: Set all field of mlx5_irq before inserting it to the xarrayShay Drory1-1/+1
Currently irq->pool is set after the irq is insert to the xarray. Set irq->pool before the irq is inserted to the xarray. Fixes: 71e084e26414 ("net/mlx5: Allocating a pool of MSI-X vectors for SFs") Signed-off-by: Shay Drory <[email protected]> Reviewed-by: Parav Pandit <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09net/mlx5: Fix order of functions in mlx5_irq_detach_nb()Shay Drory1-1/+4
Change order of functions in mlx5_irq_detach_nb() so it will be a mirror of mlx5_irq_attach_nb. Fixes: 71e084e26414 ("net/mlx5: Allocating a pool of MSI-X vectors for SFs") Signed-off-by: Shay Drory <[email protected]> Reviewed-by: Parav Pandit <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09net/mlx5: Block switchdev mode while devlink traps are activeAya Levin1-3/+11
Since switchdev mode can't support devlink traps, verify there are no active devlink traps before moving eswitch to switchdev mode. If there are active traps, prevent the switchdev mode configuration. Fixes: eb3862a0525d ("net/mlx5e: Enable traps according to link state") Signed-off-by: Aya Levin <[email protected]> Reviewed-by: Moshe Shemesh <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09net/mlx5e: Destroy page pool after XDP SQ to fix use-after-freeMaxim Mikityanskiy1-10/+10
mlx5e_close_xdpsq does the cleanup: it calls mlx5e_free_xdpsq_descs to free the outstanding descriptors, which relies on mlx5e_page_release_dynamic and page_pool_release_page. However, page_pool_destroy is already called by this point, because mlx5e_close_rq runs before mlx5e_close_xdpsq. This commit fixes the use-after-free by swapping mlx5e_close_xdpsq and mlx5e_close_rq. The commit cited below started calling page_pool_destroy directly from the driver. Previously, the page pool was destroyed under a call_rcu from xdp_rxq_info_unreg_mem_model, which would defer the deallocation until after the XDPSQ is cleaned up. Fixes: 1da4bbeffe41 ("net: core: page_pool: add user refcnt and reintroduce page_pool_destroy") Signed-off-by: Maxim Mikityanskiy <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09net/mlx5: Bridge, fix ageing timeVlad Buslov1-2/+2
Ageing time is not converted from clock_t to jiffies which results incorrect ageing timeout calculation in workqueue update task. Fix it by applying clock_t_to_jiffies() to provided value. Fixes: c636a0f0f3f0 ("net/mlx5: Bridge, dynamic entry ageing") Signed-off-by: Vlad Buslov <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09net/mlx5e: Avoid creating tunnel headers for local routeRoi Dayan1-0/+5
It could be local and remote are on the same machine and the route result will be a local route which will result in creating encap id with src/dst mac address of 0. Fixes: a54e20b4fcae ("net/mlx5e: Add basic TC tunnel set action for SRIOV offloads") Signed-off-by: Roi Dayan <[email protected]> Reviewed-by: Maor Dickman <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09net/mlx5: DR, Add fail on error check on decapAlex Vesker1-0/+2
While processing encapsulated packet on RX, one of the fields that is checked is the inner packet length. If the length as specified in the header doesn't match the actual inner packet length, the packet is invalid and should be dropped. However, such packet caused the NIC to hang. This patch turns on a 'fail_on_error' HW bit which allows HW to drop such an invalid packet while processing RX packet and trying to decap it. Fixes: ad17dc8cf910 ("net/mlx5: DR, Move STEv0 action apply logic") Signed-off-by: Alex Vesker <[email protected]> Signed-off-by: Yevgeny Kliteynik <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09net/mlx5: Don't skip subfunction cleanup in case of error in module initLeon Romanovsky2-8/+9
Clean SF resources if mlx5 eth failed to initialize. Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver") Signed-off-by: Leon Romanovsky <[email protected]> Reviewed-by: Parav Pandit <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-08-09scsi: mpt3sas: Fix incorrectly assigned error return and checkColin Ian King1-1/+1
Currently the call to _base_static_config_pages() is assigning the error return to variable 'rc' but checking the error return in error 'r'. Fix this by assigning the error return to variable 'r' instead of 'rc'. Link: https://lore.kernel.org/r/[email protected] Fixes: 19a622c39a9d ("scsi: mpt3sas: Handle firmware faults during first half of IOC init") Signed-off-by: Colin Ian King <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]> Addresses-Coverity: ("Unused value")
2021-08-09scsi: storvsc: Log TEST_UNIT_READY errors as warningsMichael Kelley1-2/+12
Commit 08f76547f08d ("scsi: storvsc: Update error logging") added more robust logging of errors, particularly those reported as Hyper-V errors. But this change produces extra logging noise in that TEST_UNIT_READY may report errors during the normal course of detecting device adds and removes. Fix this by logging TEST_UNIT_READY errors as warnings, so that log lines are produced only if the storvsc log level is changed to WARN level on the kernel boot line. Link: https://lore.kernel.org/r/[email protected] Fixes: 08f76547f08d ("scsi: storvsc: Update error logging") Signed-off-by: Michael Kelley <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2021-08-09scsi: lpfc: Move initialization of phba->poll_list earlier to avoid crashEwan D. Milne1-1/+2
The phba->poll_list is traversed in case of an error in lpfc_sli4_hba_setup(), so it must be initialized earlier in case the error path is taken. [ 490.030738] lpfc 0000:65:00.0: 0:1413 Failed to init iocb list. [ 490.036661] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 [ 490.044485] PGD 0 P4D 0 [ 490.047027] Oops: 0000 [#1] SMP PTI [ 490.050518] CPU: 0 PID: 7 Comm: kworker/0:1 Kdump: loaded Tainted: G I --------- - - 4.18. [ 490.060511] Hardware name: Dell Inc. PowerEdge R440/0WKGTH, BIOS 1.4.8 05/22/2018 [ 490.067994] Workqueue: events work_for_cpu_fn [ 490.072371] RIP: 0010:lpfc_sli4_cleanup_poll_list+0x20/0xb0 [lpfc] [ 490.078546] Code: cf e9 04 f7 fe ff 0f 1f 40 00 0f 1f 44 00 00 41 57 49 89 ff 41 56 41 55 41 54 4d 8d a79 [ 490.097291] RSP: 0018:ffffbd1a463dbcc8 EFLAGS: 00010246 [ 490.102518] RAX: 0000000000008200 RBX: ffff945cdb8c0000 RCX: 0000000000000000 [ 490.109649] RDX: 0000000000018200 RSI: ffff9468d0e16818 RDI: 0000000000000000 [ 490.116783] RBP: ffff945cdb8c1740 R08: 00000000000015c5 R09: 0000000000000042 [ 490.123915] R10: 0000000000000000 R11: ffffbd1a463dbab0 R12: ffff945cdb8c25c0 [ 490.131049] R13: 00000000fffffff4 R14: 0000000000001800 R15: ffff945cdb8c0000 [ 490.138182] FS: 0000000000000000(0000) GS:ffff9468d0e00000(0000) knlGS:0000000000000000 [ 490.146267] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 490.152013] CR2: 0000000000000000 CR3: 000000042ca10002 CR4: 00000000007706f0 [ 490.159146] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 490.166277] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 490.173409] PKRU: 55555554 [ 490.176123] Call Trace: [ 490.178598] lpfc_sli4_queue_destroy+0x7f/0x3c0 [lpfc] [ 490.183745] lpfc_sli4_hba_setup+0x1bc7/0x23e0 [lpfc] [ 490.188797] ? kernfs_activate+0x63/0x80 [ 490.192721] ? kernfs_add_one+0xe7/0x130 [ 490.196647] ? __kernfs_create_file+0x80/0xb0 [ 490.201020] ? lpfc_pci_probe_one_s4.isra.48+0x46f/0x9e0 [lpfc] [ 490.206944] lpfc_pci_probe_one_s4.isra.48+0x46f/0x9e0 [lpfc] [ 490.212697] lpfc_pci_probe_one+0x179/0xb70 [lpfc] [ 490.217492] local_pci_probe+0x41/0x90 [ 490.221246] work_for_cpu_fn+0x16/0x20 [ 490.224994] process_one_work+0x1a7/0x360 [ 490.229009] ? create_worker+0x1a0/0x1a0 [ 490.232933] worker_thread+0x1cf/0x390 [ 490.236687] ? create_worker+0x1a0/0x1a0 [ 490.240612] kthread+0x116/0x130 [ 490.243846] ? kthread_flush_work_fn+0x10/0x10 [ 490.248293] ret_from_fork+0x35/0x40 [ 490.251869] Modules linked in: lpfc(+) xt_CHECKSUM ipt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4i [ 490.332609] CR2: 0000000000000000 Link: https://lore.kernel.org/r/[email protected] Fixes: 93a4d6f40198 ("scsi: lpfc: Add registration for CPU Offline/Online events") Cc: [email protected] Reviewed-by: James Smart <[email protected]> Signed-off-by: Ewan D. Milne <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2021-08-09blk-iocost: fix lockdep warning on blkcg->lockMing Lei1-4/+4
blkcg->lock depends on q->queue_lock which may depend on another driver lock required in irq context, one example is dm-thin: Chain exists of: &pool->lock#3 --> &q->queue_lock --> &blkcg->lock Possible interrupt unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&blkcg->lock); local_irq_disable(); lock(&pool->lock#3); lock(&q->queue_lock); <Interrupt> lock(&pool->lock#3); Fix the issue by using spin_lock_irq(&blkcg->lock) in ioc_weight_write(). Cc: Tejun Heo <[email protected]> Reported-by: Bruno Goncalves <[email protected]> Link: https://lore.kernel.org/linux-block/CA+QYu4rzz6079ighEanS3Qq_Dmnczcf45ZoJoHKVLVATTo1e4Q@mail.gmail.com/T/#u Signed-off-by: Ming Lei <[email protected]> Acked-by: Tejun Heo <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jens Axboe <[email protected]>
2021-08-09io_uring: fix ctx-exit io_rsrc_put_work() deadlockPavel Begunkov1-7/+8
__io_rsrc_put_work() might need ->uring_lock, so nobody should wait for rsrc nodes holding the mutex. However, that's exactly what io_ring_ctx_free() does with io_wait_rsrc_data(). Split it into rsrc wait + dealloc, and move the first one out of the lock. Cc: [email protected] Fixes: b60c8dce33895 ("io_uring: preparation for rsrc tagging") Signed-off-by: Pavel Begunkov <[email protected]> Link: https://lore.kernel.org/r/0130c5c2693468173ec1afab714e0885d2c9c363.1628559783.git.asml.silence@gmail.com Signed-off-by: Jens Axboe <[email protected]>
2021-08-09io_uring: drop ctx->uring_lock before flushing work itemJens Axboe1-2/+4
Ammar reports that he's seeing a lockdep splat on running test/rsrc_tags from the regression suite: ====================================================== WARNING: possible circular locking dependency detected 5.14.0-rc3-bluetea-test-00249-gc7d102232649 #5 Tainted: G OE ------------------------------------------------------ kworker/2:4/2684 is trying to acquire lock: ffff88814bb1c0a8 (&ctx->uring_lock){+.+.}-{3:3}, at: io_rsrc_put_work+0x13d/0x1a0 but task is already holding lock: ffffc90001c6be70 ((work_completion)(&(&ctx->rsrc_put_work)->work)){+.+.}-{0:0}, at: process_one_work+0x1bc/0x530 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 ((work_completion)(&(&ctx->rsrc_put_work)->work)){+.+.}-{0:0}: __flush_work+0x31b/0x490 io_rsrc_ref_quiesce.part.0.constprop.0+0x35/0xb0 __do_sys_io_uring_register+0x45b/0x1060 do_syscall_64+0x35/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae -> #0 (&ctx->uring_lock){+.+.}-{3:3}: __lock_acquire+0x119a/0x1e10 lock_acquire+0xc8/0x2f0 __mutex_lock+0x86/0x740 io_rsrc_put_work+0x13d/0x1a0 process_one_work+0x236/0x530 worker_thread+0x52/0x3b0 kthread+0x135/0x160 ret_from_fork+0x1f/0x30 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock((work_completion)(&(&ctx->rsrc_put_work)->work)); lock(&ctx->uring_lock); lock((work_completion)(&(&ctx->rsrc_put_work)->work)); lock(&ctx->uring_lock); *** DEADLOCK *** 2 locks held by kworker/2:4/2684: #0: ffff88810004d938 ((wq_completion)events){+.+.}-{0:0}, at: process_one_work+0x1bc/0x530 #1: ffffc90001c6be70 ((work_completion)(&(&ctx->rsrc_put_work)->work)){+.+.}-{0:0}, at: process_one_work+0x1bc/0x530 stack backtrace: CPU: 2 PID: 2684 Comm: kworker/2:4 Tainted: G OE 5.14.0-rc3-bluetea-test-00249-gc7d102232649 #5 Hardware name: Acer Aspire ES1-421/OLVIA_BE, BIOS V1.05 07/02/2015 Workqueue: events io_rsrc_put_work Call Trace: dump_stack_lvl+0x6a/0x9a check_noncircular+0xfe/0x110 __lock_acquire+0x119a/0x1e10 lock_acquire+0xc8/0x2f0 ? io_rsrc_put_work+0x13d/0x1a0 __mutex_lock+0x86/0x740 ? io_rsrc_put_work+0x13d/0x1a0 ? io_rsrc_put_work+0x13d/0x1a0 ? io_rsrc_put_work+0x13d/0x1a0 ? process_one_work+0x1ce/0x530 io_rsrc_put_work+0x13d/0x1a0 process_one_work+0x236/0x530 worker_thread+0x52/0x3b0 ? process_one_work+0x530/0x530 kthread+0x135/0x160 ? set_kthread_struct+0x40/0x40 ret_from_fork+0x1f/0x30 which is due to holding the ctx->uring_lock when flushing existing pending work, while the pending work flushing may need to grab the uring lock if we're using IOPOLL. Fix this by dropping the uring_lock a bit earlier as part of the flush. Cc: [email protected] Link: https://github.com/axboe/liburing/issues/404 Tested-by: Ammar Faizi <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2021-08-09io-wq: fix IO_WORKER_F_FIXED issue in create_io_worker()Hao Xu1-7/+11
There may be cases like: A B spin_lock(wqe->lock) nr_workers is 0 nr_workers++ spin_unlock(wqe->lock) spin_lock(wqe->lock) nr_wokers is 1 nr_workers++ spin_unlock(wqe->lock) create_io_worker() acct->worker is 1 create_io_worker() acct->worker is 1 There should be one worker marked IO_WORKER_F_FIXED, but no one is. Fix this by introduce a new agrument for create_io_worker() to indicate if it is the first worker. Fixes: 3d4e4face9c1 ("io-wq: fix no lock protection of acct->nr_worker") Signed-off-by: Hao Xu <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jens Axboe <[email protected]>
2021-08-09io-wq: fix bug of creating io-wokers unconditionallyHao Xu1-2/+10
The former patch to add check between nr_workers and max_workers has a bug, which will cause unconditionally creating io-workers. That's because the result of the check doesn't affect the call of create_io_worker(), fix it by bringing in a boolean value for it. Fixes: 21698274da5b ("io-wq: fix lack of acct->nr_workers < acct->max_workers judgement") Signed-off-by: Hao Xu <[email protected]> Link: https://lore.kernel.org/r/[email protected] [axboe: drop hunk that isn't strictly needed] Signed-off-by: Jens Axboe <[email protected]>
2021-08-09io_uring: rsrc ref lock needs to be IRQ safeJens Axboe1-14/+5
Nadav reports running into the below splat on re-enabling softirqs: WARNING: CPU: 2 PID: 1777 at kernel/softirq.c:364 __local_bh_enable_ip+0xaa/0xe0 Modules linked in: CPU: 2 PID: 1777 Comm: umem Not tainted 5.13.1+ #161 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/22/2020 RIP: 0010:__local_bh_enable_ip+0xaa/0xe0 Code: a9 00 ff ff 00 74 38 65 ff 0d a2 21 8c 7a e8 ed 1a 20 00 fb 66 0f 1f 44 00 00 5b 41 5c 5d c3 65 8b 05 e6 2d 8c 7a 85 c0 75 9a <0f> 0b eb 96 e8 2d 1f 20 00 eb a5 4c 89 e7 e8 73 4f 0c 00 eb ae 65 RSP: 0018:ffff88812e58fcc8 EFLAGS: 00010046 RAX: 0000000000000000 RBX: 0000000000000201 RCX: dffffc0000000000 RDX: 0000000000000007 RSI: 0000000000000201 RDI: ffffffff8898c5ac RBP: ffff88812e58fcd8 R08: ffffffff8575dbbf R09: ffffed1028ef14f9 R10: ffff88814778a7c3 R11: ffffed1028ef14f8 R12: ffffffff85c9e9ae R13: ffff88814778a000 R14: ffff88814778a7b0 R15: ffff8881086db890 FS: 00007fbcfee17700(0000) GS:ffff8881e0300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000c0402a5008 CR3: 000000011c1ac003 CR4: 00000000003706e0 Call Trace: _raw_spin_unlock_bh+0x31/0x40 io_rsrc_node_ref_zero+0x13e/0x190 io_dismantle_req+0x215/0x220 io_req_complete_post+0x1b8/0x720 __io_complete_rw.isra.0+0x16b/0x1f0 io_complete_rw+0x10/0x20 where it's clear we end up calling the percpu count release directly from the completion path, as it's in atomic mode and we drop the last ref. For file/block IO, this can be from IRQ context already, and the softirq locking for rsrc isn't enough. Just make the lock fully IRQ safe, and ensure we correctly safe state from the release path as we don't know the full context there. Reported-by: Nadav Amit <[email protected]> Tested-by: Nadav Amit <[email protected]> Link: https://lore.kernel.org/io-uring/[email protected]/ Signed-off-by: Jens Axboe <[email protected]>
2021-08-09Merge branch 'for-5.14-fixes' of ↵Linus Torvalds2-14/+19
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup Pull cgroup fix from Tejun Heo: "One commit to fix a possible A-A deadlock around u64_stats_sync on 32bit machines caused by updating it without disabling IRQ when it may be read from IRQ context" * 'for-5.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: cgroup: rstat: fix A-A deadlock on 32bit around u64_stats_sync
2021-08-09bareudp: Fix invalid read beyond skb's linear dataGuillaume Nault1-5/+11
Data beyond the UDP header might not be part of the skb's linear data. Use skb_copy_bits() instead of direct access to skb->data+X, so that we read the correct bytes even on a fragmented skb. Fixes: 4b5f67232d95 ("net: Special handling for IP & MPLS.") Signed-off-by: Guillaume Nault <[email protected]> Link: https://lore.kernel.org/r/7741c46545c6ef02e70c80a9b32814b22d9616b3.1628264975.git.gnault@redhat.com Signed-off-by: Jakub Kicinski <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.