| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
- Return error instead of success if DMA mapping of MSI area fails (Jiantao
Zhang)
- Drop tegra194 MSI register save/restore, which is unnecessary since the
DWC core does it (Jisheng Zhang)
- Factor out qcom enable/disable resources code (Dmitry Baryshkov)
- Remove "snps,dw-pcie" from rockchip-dwc DT "compatible" property because
it's not fully compatible with rockchip (Peter Geis)
- Reset rockchip-dwc controller at probe (Peter Geis)
- Add rockchip-dwc INTx support (Peter Geis)
* remotes/lorenzo/pci/dwc:
PCI: rockchip-dwc: Add legacy interrupt support
PCI: rockchip-dwc: Reset core at driver probe
dt-bindings: PCI: Remove fallback from Rockchip DesignWare binding
PCI: qcom-ep: Move enable/disable resources code to common functions
PCI: tegra194: Remove unnecessary MSI enable reg save and restore
PCI: dwc: Fix setting error return on MSI DMA mapping failure
|
|
- Fix bitmap size when searching for free outbound region (Dan Carpenter)
- Do device-specific setup to allow PTM Responder to be enabled (Christian
Gmeiner)
- Don't advertise FLR in Device Capabilities register because the
controller incorrectly resets Margining Lane Status and Margining Lane
Control on FLR (Parshuram Thombare)
* remotes/lorenzo/pci/cadence:
PCI: cadence: Clear FLR in device capabilities register
PCI: cadence: Allow PTM Responder to be enabled
PCI: cadence: Fix find_first_zero_bit() limit
|
|
- Avoid pci_dev_lock() AB/BA deadlock with sriov_numvfs_store() (Yicong
Yang, Jay Zhou)
* pci/virtualization:
PCI: Avoid pci_dev_lock() AB/BA deadlock with sriov_numvfs_store()
|
|
- Clip only host bridge windows for E820 regions and log what is clipped
(Bjorn Helgaas)
- Add kernel cmdline options to use/ignore E820 reserved regions (Hans de
Goede)
- Disable E820 reserved region clipping for IdeaPads, Yoga, Yoga Slip, Acer
Spin 5, Clevo Barebone systems where clipping leaves no usable address
space for touchpads, Thunderbolt devices, etc (Hans de Goede)
- Disable E820 reserved region clipping by default starting in 2023 (Hans
de Goede)
* pci/resource:
x86/PCI: Disable E820 reserved region clipping starting in 2023
x86/PCI: Disable E820 reserved region clipping via quirks
x86/PCI: Add kernel cmdline options to use/ignore E820 reserved regions
x86/PCI: Clip only host bridge windows for E820 regions
x86: Log resource clipping for E820 regions
x86/PCI: Eliminate remove_e820_regions() common subexpressions
|
|
- Define pci_restore_standard_config() only for CONFIG_PM_SLEEP, since it's
not used otherwise (Krzysztof Kozlowski)
- Power up all devices during runtime resume (Rafael J. Wysocki)
- Resume subordinate bus in bus type callbacks (Rafael J. Wysocki)
- Drop pci_dev runtime_d3cold flag since no uses remain (Rafael J. Wysocki)
- Move power-up to D0 code to pci_power_up() and rename
pci_raw_set_power_state() to pci_set_low_power_state() (Rafael J.
Wysocki)
- Set current_state to D3cold if the device is not accessible (Rafael J.
Wysocki)
- Do not call pci_update_current_state() from pci_power_up() (Rafael J.
Wysocki)
- Write 0 to PMCSR in pci_power_up() in all cases (Rafael J. Wysocki)
- Split part of pci_power_up() off to pci_set_full_power_state() (Rafael J.
Wysocki)
- Do not restore BARs if device is not in D0 (Rafael J. Wysocki)
* pci/pm:
PCI/PM: Replace pci_set_power_state() in pci_pm_thaw_noirq()
PCI/PM: Rearrange pci_set_power_state()
PCI/PM: Clean up pci_set_low_power_state()
PCI/PM: Do not restore BARs if device is not in D0
PCI/PM: Split pci_power_up()
PCI/PM: Write 0 to PMCSR in pci_power_up() in all cases
PCI/PM: Do not call pci_update_current_state() from pci_power_up()
PCI/PM: Unfold pci_platform_power_transition() in pci_power_up()
PCI/PM: Set current_state to D3cold if the device is not accessible
PCI/PM: Relocate pci_set_low_power_state()
PCI/PM: Split pci_raw_set_power_state()
PCI/PM: Rearrange pci_update_current_state()
PCI/PM: Drop the runtime_d3cold device flag
PCI/PM: Resume subordinate bus in bus type callbacks
PCI/PM: Power up all devices during runtime resume
PCI/PM: Define pci_restore_standard_config() only for CONFIG_PM_SLEEP
|
|
- Update pci_p2pdma_whitelist[] checking so we accept Skylake-E Root Ports
even if they're not at devfn 00.0 (Shlomo Pongratz)
* pci/p2pdma:
PCI/P2PDMA: Whitelist Intel Skylake-E Root Ports at any devfn
|
|
- Change pci_set_dma_mask() documentation references to dma_set_mask()
(Alex Williamson)
* pci/misc:
PCI/doc: Update obsolete pci_set_dma_mask() references
|
|
- Allow D3 only if Root Port can signal and wake from D3 so we don't miss
hotplug events on AMD Yellow Carp (Mario Limonciello)
- Clean up hotplug include files to enable future powerpc cleanup
(Christophe Leroy)
* pci/hotplug:
PCI: hotplug: Clean up include files
PCI/ACPI: Allow D3 only if Root Port can signal and wake from D3
|
|
- Clear AER "multiple errors" bits to avoid race that left them set forever
(Kuppuswamy Sathyanarayanan)
* pci/error:
PCI/AER: Clear MULTI_ERR_COR/UNCOR_RCV bits
|
|
- Quirk Intel DG2 ASPM L1 acceptable latency to be unlimited. The device
advertises that it can only tolerate 1us, which means L1 is rarely if
ever used (Mika Westerberg)
* pci/aspm:
PCI/ASPM: Make Intel DG2 L1 acceptable latency unlimited
|
|
Some firmware includes unusable space (host bridge registers, hidden PCI
device BARs, etc) in PCI host bridge _CRS. As far as we know, there's
nothing in the ACPI, UEFI, or PCI Firmware spec that requires the OS to
remove E820 reserved regions from _CRS, so this seems like a firmware
defect.
As a workaround, 4dc2287c1805 ("x86: avoid E820 regions when allocating
address space") has clipped out the unusable space in the past. This is
required for machines like the following:
- Dell Precision T3500 (the original motivator for 4dc2287c1805); see
https://bugzilla.kernel.org/show_bug.cgi?id=16228
- Asus C523NA (Coral) Chromebook; see
https://lore.kernel.org/all/[email protected]/
- Lenovo ThinkPad X1 Gen 2; see:
https://bugzilla.redhat.com/show_bug.cgi?id=2029207
But other firmware supplies E820 reserved regions that cover entire _CRS
windows, and clipping throws away the entire window, leaving none for
hot-added or uninitialized devices. This clipping breaks a whole range of
Lenovo IdeaPads, Yogas, Yoga Slims, and notebooks, as well as Acer Spin 5
and Clevo X170KM-G Barebone machines.
E820 reserved entries that cover a memory-mapped PCI host bridge, including
its registers and memory/IO windows, are probably *not* a firmware defect.
Per ACPI v5.4, sec 15.2, the E820 memory map may include:
Address ranges defined for baseboard memory-mapped I/O devices, such as
APICs, are returned as reserved.
Disable the E820 clipping by default for all post-2022 machines. We
already have quirks to disable clipping for pre-2023 machines, and we'll
likely need quirks to *enable* clipping for post-2022 machines that
incorrectly include unusable space in _CRS, including Chromebooks and
Lenovo ThinkPads.
Here's the rationale for doing this. If we do nothing, and continue
clipping by default:
- Future systems like the Lenovo IdeaPads, Yogas, etc, Acer Spin, and
Clevo Barebones will require new quirks to disable clipping.
- The problem here is E820 entries that cover entire _CRS windows that
should not be clipped out.
- I think these E820 entries are legal per spec, and it would be hard to
get BIOS vendors to change them.
- We will discover new systems that need clipping disabled piecemeal as
they are released.
- Future systems like Lenovo X1 Carbon and the Chromebooks (probably
anything using coreboot) will just work, even though their _CRS is
incorrect, so we will not notice new ones that rely on the clipping.
- BIOS updates will not require new quirks unless they change the DMI
model string.
If we add the date check in this commit that disables clipping, e.g., "no
clipping when date >= 2023":
- Future systems like Lenovo *IIL*, Acer Spin, and Clevo Barebones will
just work without new quirks.
- Future systems like Lenovo X1 Carbon and the Chromebooks will require
new quirks to *enable* clipping.
- The problem here is that _CRS contains regions that are not usable by
PCI devices, and we rely on the E820 kludge to clip them out.
- I think this use of E820 is clearly a firmware bug, so we have a
fighting chance of getting it changed eventually.
- BIOS updates after the cutoff date *will* require quirks, but only for
systems like Lenovo X1 Carbon and Chromebooks that we already think
have broken firmware.
It seems to me like it's better to add quirks for firmware that we think is
broken than for firmware that seems unusual but correct.
[bhelgaas: comment and commit log]
Link: https://lore.kernel.org/linux-pci/20220518220754.GA7911@bhelgaas/
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Acked-by: Rafael J. Wysocki <[email protected]>
Cc: Benoit Grégoire <[email protected]>
Cc: Hui Wang <[email protected]>
|
|
To avoid unusable space that some firmware includes in PCI host bridge
_CRS, Linux currently excludes E820 reserved regions from _CRS windows; see
4dc2287c1805 ("x86: avoid E820 regions when allocating address space").
However, some systems supply E820 reserved regions that cover the entire
memory window from _CRS, so clipping them out leaves no space for hot-added
or uninitialized PCI devices.
For example, from a Lenovo IdeaPad 3 15IIL 81WE:
BIOS-e820: [mem 0x4bc50000-0xcfffffff] reserved
pci_bus 0000:00: root bus resource [mem 0x65400000-0xbfffffff window]
pci 0000:00:15.0: BAR 0: [mem 0x00000000-0x00000fff 64bit]
pci 0000:00:15.0: BAR 0: no space for [mem size 0x00001000 64bit]
Add quirks to disable the E820 clipping for machines known to do this.
A single DMI_PRODUCT_VERSION "IIL" quirk matches all the below:
Lenovo IdeaPad 3 14IIL05
Lenovo IdeaPad 3 15IIL05
Lenovo IdeaPad 3 17IIL05
Lenovo IdeaPad 5 14IIL05
Lenovo IdeaPad 5 15IIL05
Lenovo IdeaPad Slim 7 14IIL05
Lenovo IdeaPad Slim 7 15IIL05
Lenovo IdeaPad S145-15IIL
Lenovo IdeaPad S340-14IIL
Lenovo IdeaPad S340-15IIL
Lenovo IdeaPad C340-15IIL
Lenovo BS145-15IIL
Lenovo V14-IIL
Lenovo V15-IIL
Lenovo V17-IIL
Lenovo Yoga C940-14IIL
Lenovo Yoga S740-14IIL
Lenovo Yoga Slim 7 14IIL05
Lenovo Yoga Slim 7 15IIL05
in addition to the following that don't actually need it because they have
no E820 reserved regions that overlap _CRS windows:
Lenovo IdeaPad Flex 5 14IIL05
Lenovo IdeaPad Flex 5 15IIL05
Lenovo ThinkBook 14-IIL
Lenovo ThinkBook 15-IIL
Lenovo Yoga S940-14IIL
Other quirks match these:
Acer Spin 5 (SP513-54N)
Clevo X170KM-G Barebone
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206459 Lenovo Yoga C940-14IIL
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214259 Clevo X170KM Barebone
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1868899 Lenovo IdeaPad 3 15IIL05
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1871793 Lenovo IdeaPad 5 14IIL05
Link: https://bugs.launchpad.net/bugs/1878279 Lenovo IdeaPad 5 14IIL05
Link: https://bugs.launchpad.net/bugs/1880172 Lenovo IdeaPad 3 14IIL05
Link: https://bugs.launchpad.net/bugs/1884232 Acer Spin SP513-54N
Link: https://bugs.launchpad.net/bugs/1921649 Lenovo IdeaPad S145
Link: https://bugs.launchpad.net/bugs/1931715 Lenovo IdeaPad S145
Link: https://bugs.launchpad.net/bugs/1932069 Lenovo BS145-15IIL
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Acked-by: Rafael J. Wysocki <[email protected]>
Cc: Benoit Grégoire <[email protected]>
Cc: Hui Wang <[email protected]>
|
|
Some firmware supplies PCI host bridge _CRS that includes address space
unusable by PCI devices, e.g., space occupied by host bridge registers or
used by hidden PCI devices.
To avoid this unusable space, Linux currently excludes E820 reserved
regions from _CRS windows; see 4dc2287c1805 ("x86: avoid E820 regions when
allocating address space").
However, this use of E820 reserved regions to clip things out of _CRS is
not supported by ACPI, UEFI, or PCI Firmware specs, and some systems have
E820 reserved regions that cover the entire memory window from _CRS.
4dc2287c1805 clips the entire window, leaving no space for hot-added or
uninitialized PCI devices.
For example, from a Lenovo IdeaPad 3 15IIL 81WE:
BIOS-e820: [mem 0x4bc50000-0xcfffffff] reserved
pci_bus 0000:00: root bus resource [mem 0x65400000-0xbfffffff window]
pci 0000:00:15.0: BAR 0: [mem 0x00000000-0x00000fff 64bit]
pci 0000:00:15.0: BAR 0: no space for [mem size 0x00001000 64bit]
Future patches will add quirks to enable/disable E820 clipping
automatically.
Add a "pci=no_e820" kernel command line option to disable clipping with
E820 reserved regions. Also add a matching "pci=use_e820" option to enable
clipping with E820 reserved regions if that has been disabled by default by
further patches in this patch-set.
Both options taint the kernel because they are intended for debugging and
workaround purposes until a quirk can set them automatically.
[bhelgaas: commit log, add printk]
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1868899 Lenovo IdeaPad 3
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Acked-by: Rafael J. Wysocki <[email protected]>
Cc: Benoit Grégoire <[email protected]>
Cc: Hui Wang <[email protected]>
|
|
When a Root Port or Root Complex Event Collector receives an error Message
e.g., ERR_COR, it sets PCI_ERR_ROOT_COR_RCV in the Root Error Status
register and logs the Requester ID in the Error Source Identification
register. If it receives a second ERR_COR Message before software clears
PCI_ERR_ROOT_COR_RCV, hardware sets PCI_ERR_ROOT_MULTI_COR_RCV and the
Requester ID is lost.
In the following scenario, PCI_ERR_ROOT_MULTI_COR_RCV was never cleared:
- hardware receives ERR_COR message
- hardware sets PCI_ERR_ROOT_COR_RCV
- aer_irq() entered
- aer_irq(): status = pci_read_config_dword(PCI_ERR_ROOT_STATUS)
- aer_irq(): now status == PCI_ERR_ROOT_COR_RCV
- hardware receives second ERR_COR message
- hardware sets PCI_ERR_ROOT_MULTI_COR_RCV
- aer_irq(): pci_write_config_dword(PCI_ERR_ROOT_STATUS, status)
- PCI_ERR_ROOT_COR_RCV is cleared; PCI_ERR_ROOT_MULTI_COR_RCV is set
- aer_irq() entered again
- aer_irq(): status = pci_read_config_dword(PCI_ERR_ROOT_STATUS)
- aer_irq(): now status == PCI_ERR_ROOT_MULTI_COR_RCV
- aer_irq() exits because PCI_ERR_ROOT_COR_RCV not set
- PCI_ERR_ROOT_MULTI_COR_RCV is still set
The same problem occurred with ERR_NONFATAL/ERR_FATAL Messages and
PCI_ERR_ROOT_UNCOR_RCV and PCI_ERR_ROOT_MULTI_UNCOR_RCV.
Fix the problem by queueing an AER event and clearing the Root Error Status
bits when any of these bits are set:
PCI_ERR_ROOT_COR_RCV
PCI_ERR_ROOT_UNCOR_RCV
PCI_ERR_ROOT_MULTI_COR_RCV
PCI_ERR_ROOT_MULTI_UNCOR_RCV
See the bugzilla link for details from Eric about how to reproduce this
problem.
[bhelgaas: commit log, move repro details to bugzilla]
Fixes: e167bfcaa4cd ("PCI: aerdrv: remove magical ROOT_ERR_STATUS_MASKS")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215992
Link: https://lore.kernel.org/r/20220418150237.1021519-1-sathyanarayanan.kuppuswamy@linux.intel.com
Reported-by: Eric Badger <[email protected]>
Signed-off-by: Kuppuswamy Sathyanarayanan <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Ashok Raj <[email protected]>
|
|
Clear FLR (Function Level Reset) from device capabilities
registers for all physical functions.
During FLR, the Margining Lane Status and Margining Lane Control
registers should not be reset, as per PCIe specification.
However, the controller incorrectly resets these registers upon FLR.
This causes PCISIG compliance FLR test to fail. Hence preventing
all functions from advertising FLR support if flag quirk_disable_flr
is set.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Parshuram Thombare <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
This enables the Controller [RP] to automatically respond with
Response/ResponseD messages if CDNS_PCIE_LM_TPM_CTRL_PTMRSEN
and PCI_PTM_CTRL_ENABLE bits are both set.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Christian Gmeiner <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
The sysfs sriov_numvfs_store() path acquires the device lock before the
config space access lock:
sriov_numvfs_store
device_lock # A (1) acquire device lock
sriov_configure
vfio_pci_sriov_configure # (for example)
vfio_pci_core_sriov_configure
pci_disable_sriov
sriov_disable
pci_cfg_access_lock
pci_wait_cfg # B (4) wait for dev->block_cfg_access == 0
Previously, pci_dev_lock() acquired the config space access lock before the
device lock:
pci_dev_lock
pci_cfg_access_lock
dev->block_cfg_access = 1 # B (2) set dev->block_cfg_access = 1
device_lock # A (3) wait for device lock
Any path that uses pci_dev_lock(), e.g., pci_reset_function(), may
deadlock with sriov_numvfs_store() if the operations occur in the sequence
(1) (2) (3) (4).
Avoid the deadlock by reversing the order in pci_dev_lock() so it acquires
the device lock before the config space access lock, the same as the
sriov_numvfs_store() path.
[bhelgaas: combined and adapted commit log from Jay Zhou's independent
subsequent posting:
https://lore.kernel.org/r/[email protected]]
Link: https://lore.kernel.org/linux-pci/[email protected]/
Also-posted-by: Jay Zhou <[email protected]>
Signed-off-by: Yicong Yang <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
The legacy interrupts on the rk356x PCIe controller are handled by a
single muxed interrupt. Add IRQ domain support to the pcie-dw-rockchip
driver to support the virtual domain.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Peter Geis <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Marc Zyngier <[email protected]>
|
|
The PCIe controller is in an unknown state at driver probe. This can
lead to undesireable effects when the driver attempts to configure the
controller.
Prevent issues in the future by resetting the core during probe.
Link: https://lore.kernel.org/r/[email protected]
Tested-by: Nicolas Frattaroli <[email protected]>
Signed-off-by: Peter Geis <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
The snps,dw-pcie binds to a standalone driver. It is not fully
compatible with the Rockchip implementation and causes a hang if it
binds to the device.
Remove this binding as a valid fallback.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Peter Geis <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
|
|
Remove code duplication by moving the code related to enabling/disabling
the resources (PHY, CLK, Reset) to common functions so that they can be
called from multiple places.
[mani: renamed the functions and reworded the commit message]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
Calling pci_set_power_state() to put the given device into D0 in
pci_pm_thaw_noirq() may cause it to restore the device's BARs, which is
redundant before calling pci_restore_state(), so replace it with a direct
pci_power_up() call followed by pci_update_current_state() if it returns a
nonzero value, in analogy with pci_pm_default_resume_early().
Avoid code duplication by introducing a wrapper function to contain the
repeating pattern and calling it in both places.
Link: https://lore.kernel.org/r/3639079.MHq7AAxBmi@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
The part of pci_set_power_state() related to transitions into
low-power states is unnecessary convoluted, so clearly divide it
into the D3cold special case and the general case covering all of
the other states.
Also fix a potential issue with calling pci_bus_set_current_state()
to set the current state of all devices on the subordinate bus to
D3cold without checking if the power state of the parent bridge has
really changed to D3cold.
Link: https://lore.kernel.org/r/2139440.Mh6RI2rZIc@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Mika Westerberg <[email protected]>
|
|
Make the following assorted non-essential changes in
pci_set_low_power_state():
1. Drop two redundant checks from it (the caller takes care of these
conditions).
2. Change the log level of a messages printed by it to "debug",
because it only indicates a programming mistake.
Link: https://lore.kernel.org/r/2539071.Lt9SDvczpP@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Mika Westerberg <[email protected]>
|
|
Do not attempt to restore the device's BARs in
pci_set_full_power_state() if the actual current
power state of the device is not D0.
Link: https://lore.kernel.org/r/1849718.CQOukoFCf9@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
One of the two callers of pci_power_up() invokes
pci_update_current_state() and pci_restore_state() right after calling
it, in which case running the part of it happening after the mandatory
transition delays is redundant, so move that part out of it into a new
function called pci_set_full_power_state() that will be invoked from
pci_set_power_state() which is the other caller of pci_power_up().
Link: https://lore.kernel.org/r/1942150.usQuhbGJ8B@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
Make pci_power_up() write 0 to the device's PCI_PM_CTRL register in
order to put it into D0 regardless of the power state returned by
the previous read from that register which should not matter.
Link: https://lore.kernel.org/r/5748066.MhkbZ0Pkbq@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
Notice that calling pci_update_current_state() from pci_power_up() is
redundant and may be harmful in some cases.
First, if the device is in a low-power state before pci_power_up()
gets called for it and platform_pci_set_power_state() successfully
changes its power state to D0, pci_update_current_state() will update
current_state to reflect that and pci_power_up() will return success
right away without restoring the device's BARs or reconfiguring ASPM
which may be necessary. This is arguably incorrect and definitely
inconsistent with the case when platform_pci_set_power_state() returns
an error (for example, because the device is not power-manageable by
the platform firmware).
Second, current_state should not be overwritten until the decision
whether or not to restore the device's BARs is made, because that
decision generally depends on its value. Again, calling
pci_update_current_state() in pci_power_up() is not consistent with
this observation.
Next, pci_power_up() attempts to read from the device's PCI_PM_CTRL
register regardless of the current_state value unless it is PCI_D0,
including the case when pci_update_current_state() sets current_state
to PCI_D3cold to indicate that the device is not accessible. If the
register read is not successful, current_state will be set to
PCI_D3cold anyway, so that pci_update_current_state() action is
redundant.
Further, if pci_update_current_state() reads the device's PCI_PM_CTRL
register, pci_power_up() will repeat that read going forward and
it is not necessary to update current_state in the meantime.
Finally, if pm_cap is not set (in which case the PCI_PM_CTRL register
is not present), the power state of the device should be determined
with the help of the platform firmware or set to D0 if that's not
possible and pci_update_current_state() does not do that.
Accordingly, rearrange pci_power_up() so as to address the above
shortcomings.
Link: https://lore.kernel.org/r/3695055.kQq0lBPeGt@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
Some actions carried out by pci_platform_power_transition(() in
pci_power_up() are redundant, but before dealing with them, make
pci_power_up() call the pci_platform_power_transition() code directly
(and avoid a redundant check when pm_cap is unset while at it).
Link: https://lore.kernel.org/r/1922486.PYKUYFuaPT@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
Make pci_power_up() and pci_set_low_power_state() change current_state
to PCI_D3cold when the device is not accessible along the lines of
pci_update_current_state().
Link: https://lore.kernel.org/r/10104376.nUPlyArG6x@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
Because pci_set_power_state() is the only caller of
pci_set_low_power_state(), put the latter next to the former.
No functional impact.
Link: https://lore.kernel.org/r/3202976.44csPzL39Z@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
The transitions from low-power states to D0 and the other way around
are unnecessarily tangled in pci_raw_set_power_state() which makes it
rather hard to follow.
Moreover, the only caller of pci_raw_set_power_state() passing PCI_D0
as its state argument is pci_power_up(), so the code carrying out
transitions into D0 can be put directly into that function.
Accordingly, move the code handling transitions from low-power states
into D0 directly into pci_power_up() and rename the remaining part
of pci_raw_set_power_state() to pci_set_low_power_state(), because
it only handles transitions into low-power state now.
While at it, fix up some white space, update some comments and modify
messages printed by pci_power_up() and pci_set_low_power_state() to
be less confusing (which is the only expected functional impact of
this change).
Link: https://lore.kernel.org/r/13038676.uLZWGnKmhe@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
Save one config space access in pci_update_current_state() by testing the
retrieved PCI_PM_CTRL register value against PCI_POSSIBLE_ERROR() instead
of invoking pci_device_is_present() separately.
While at it, drop a pair of unnecessary parens.
No expected functional impact.
Link: https://lore.kernel.org/r/1917095.PYKUYFuaPT@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
The runtime_d3cold flag is not needed any more, so drop it.
Link: https://lore.kernel.org/r/8077784.T7Z3S40VBb@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Mika Westerberg <[email protected]>
|
|
Calling pci_resume_bus() on the secondary bus from pci_power_up() as it is
done now is questionable, because it depends on the mandatory bridge
power-up delays that are only covered by the PCI bus type PM callbacks.
For this reason, move the subordinate bus resume to those callbacks too and
use the observation that if a bridge is being powered-up during resume from
system-wide suspend, it may be still desirable to runtime-resume its
subordinate bus after completing the system-wide transition (in case the
resume of the devices on that bus is skipped during it).
Link: https://lore.kernel.org/r/3190097.aeNJFYEL58@kreacher
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Mika Westerberg <[email protected]>
|
|
Currently, endpoint devices may not be powered up entirely during runtime
resume that follows a D3hot -> D0 transition of the parent bridge.
Namely, even if the power state of an endpoint device, as indicated by its
PCI_PM_CTRL register, is D0 after powering up its parent bridge, it may be
still necessary to bring its ACPI companion into D0 and that should be done
before accessing it. However, the current code assumes that reading the
PCI_PM_CTRL register is sufficient to establish the endpoint device's power
state, which may lead to problems.
Address that by forcing a power-up of all PCI devices, including the
platform firmware part of it, during runtime resume.
Link: https://lore.kernel.org/linux-pm/11967527.O9o76ZdvQC@kreacher
Fixes: 5775b843a619 ("PCI: Restore config space on runtime resume despite being unbound")
Link: https://lore.kernel.org/r/2652115.mvXUDI8C0e@kreacher
Reported-by: Abhishek Sahu <[email protected]>
Tested-by: Abhishek Sahu <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Mika Westerberg <[email protected]>
|
|
pci_restore_standard_config() was defined under CONFIG_PM but called only
by pci_pm_resume() (defined under CONFIG_SUSPEND) and pci_pm_restore()
(defined under CONFIG_HIBERNATE_CALLBACKS). A configuration with only
CONFIG_PM leads to a warning:
drivers/pci/pci-driver.c:533:12: error: ‘pci_restore_standard_config’ defined but not used [-Werror=unused-function]
CONFIG_PM_SLEEP depends on CONFIG_SUSPEND and CONFIG_HIBERNATE_CALLBACKS,
so define pci_restore_standard_config() under that instead.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
The function is dma_set_mask(), fix a missed instance of the old
pci_set_dma_mask() and a reference to a function that doesn't exist.
Fixes: 05b0ebd06ae6 ("PCI/doc: cleanup references to the legacy PCI DMA API")
Link: https://lore.kernel.org/r/165048747271.2959320.13475081883467312497.stgit@omen
Signed-off-by: Alex Williamson <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
|
|
In 7b94b53db34f ("PCI/P2PDMA: Add Intel Sky Lake-E Root Ports B, C, D to
the whitelist"), Andrew Maier added Skylake-E 2031, 2032, and 2033 Root
Ports to the pci_p2pdma_whitelist[], so we assume P2PDMA between devices
below these ports works.
Previously we only checked the whitelist for a device at devfn 00.0 on the
root bus, which is often a "host bridge". But these Skylake Root Ports may
be at any devfn and there may be no "host bridge" device.
Generalize pci_host_bridge_dev() so we check the first device on the root
bus, whether it is devfn 00.0 or a PCIe Root Port, against the whitelist.
[bhelgaas: commit log, comment]
Link: https://lore.kernel.org/r/[email protected]
Tested-by: Maor Gottlieb <[email protected]>
Signed-off-by: Shlomo Pongratz <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Cc: Andrew Maier <[email protected]>
|
|
The integrated MSI Receiver enable register is always initialized in
dw_pcie_setup_rc() which is also called in resume code path, so we
don't need to save/restore the enable register during suspend/resume.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jisheng Zhang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Vidya Sagar <[email protected]>
|
|
ACPI firmware advertises PCI host bridge resources via PNP0A03 _CRS
methods. Some BIOSes include non-window address space in _CRS, and if we
allocate that non-window space for PCI devices, they don't work.
4dc2287c1805 ("x86: avoid E820 regions when allocating address space")
works around this issue by clipping out any regions mentioned in the E820
table in the allocate_resource() path, but the implementation has a couple
issues:
- The clipping is done for *all* allocations, not just those for PCI
address space, and
- The clipping is done at each allocation instead of being done once when
setting up the host bridge windows.
Rework the implementation so we only clip PCI host bridge windows, and we
do it once when setting them up.
Example output changes:
BIOS-e820: [mem 0x00000000b0000000-0x00000000c00fffff] reserved
+ acpi PNP0A08:00: clipped [mem 0xc0000000-0xfebfffff window] to [mem 0xc0100000-0xfebfffff window] for e820 entry [mem 0xb0000000-0xc00fffff]
- pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff window]
+ pci_bus 0000:00: root bus resource [mem 0xc0100000-0xfebfffff window]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Reviewed-by: Mika Westerberg <[email protected]>
Acked-by: Rafael J. Wysocki <[email protected]>
|
|
When remove_e820_regions() clips a resource because an E820 region overlaps
it, log a note in dmesg to add in debugging.
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
When dma_mapping_error() returns error because of no enough memory,
but dw_pcie_host_init() returns success, which will mislead the callers.
Link: https://lore.kernel.org/r/[email protected]
Fixes: 07940c369a6b ("PCI: dwc: Fix MSI page leakage in suspend/resume")
Signed-off-by: Jianrong Zhang <[email protected]>
Signed-off-by: Jiantao Zhang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
|
|
The ep->ob_region_map bitmap is a long and it has BITS_PER_LONG bits.
Link: https://lore.kernel.org/r/20220315065829.GA13572@kili
Fixes: 37dddf14f1ae ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
Intel DG2 discrete graphics PCIe endpoints advertise L1 acceptable exit
latency to be < 1us even though they can actually tolerate unlimited exit
latencies just fine. Quirk the L1 acceptable exit latency for these
endpoints to be unlimited so ASPM L1 can be enabled.
[bhelgaas: use FIELD_GET/FIELD_PREP, wordsmith comment & commit log]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mika Westerberg <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Rodrigo Vivi <[email protected]>
|
|
arch/powerpc/include/asm/prom.h includes some headers that it doesn't need
itself. Add the missing headers to files that include prom.h so we can
remove them from prom.h.
Link: https://lore.kernel.org/r/79201f5fae8d003164ac36ed3be7789db1bc5ab4.1648833421.git.christophe.leroy@csgroup.eu
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
Add local variables to reduce repetition later. No functional change
intended.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Reviewed-by: Mika Westerberg <[email protected]>
Acked-by: Rafael J. Wysocki <[email protected]>
|
|
acpi_pci_bridge_d3(dev) returns "true" if "dev" is a hotplug bridge that
can handle hotplug events while in D3. Previously this meant either:
- "dev" has a _PS0 or _PR0 method (acpi_pci_power_manageable()), or
- The Root Port above "dev" has a _DSD with a "HotPlugSupportInD3"
property with value 1.
This did not consider _PRW, which tells us about wakeup GPEs (ACPI v6.4,
sec 7.3.13). Without a wakeup GPE, from an ACPI perspective the Root Port
has no way of generating wakeup signals, so hotplug events will be lost if
we use D3.
Similarly, it did not consider _S0W, which tells us the deepest D-state
from which a device can wake itself (sec 7.3.20). If _S0W tells us the
device cannot wake from D3, hotplug events will again be lost if we use D3.
Some platforms, e.g., AMD Yellow Carp, supply "HotPlugSupportInD3" without
_PRW or with an _S0W that says the Root Port cannot wake from D3. On those
platforms, we previously put bridges in D3hot, hotplug events were lost,
and hotplugged devices would not be recognized without manually rescanning.
Allow bridges to be put in D3 only if the Root Port can generate wakeup
GPEs (wakeup.flags.valid), it can wake from D3 (_S0W), AND it has the
"HotPlugSupportInD3" property.
Neither Windows 10 nor Windows 11 puts the bridge in D3 when the firmware
is configured this way, and this change aligns the handling of the
situation to be the same.
[bhelgaas: commit log, tidy "HotPlugSupportInD3" check and comment]
Link: https://uefi.org/htmlspecs/ACPI_Spec_6_4_html/07_Power_and_Performance_Mgmt/device-power-management-objects.html?highlight=s0w#s0w-s0-device-wake-state
Link: https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#identifying-pcie-root-ports-supporting-hot-plug-in-d3
Link: https://lore.kernel.org/r/[email protected]
Fixes: 26ad34d510a87 ("PCI / ACPI: Whitelist D3 for more PCIe hotplug ports")
Signed-off-by: Mario Limonciello <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Rafael J. Wysocki <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull more tracing updates from Steven Rostedt:
- Rename the staging files to give them some meaning. Just
stage1,stag2,etc, does not show what they are for
- Check for NULL from allocation in bootconfig
- Hold event mutex for dyn_event call in user events
- Mark user events to broken (to work on the API)
- Remove eBPF updates from user events
- Remove user events from uapi header to keep it from being installed.
- Move ftrace_graph_is_dead() into inline as it is called from hot
paths and also convert it into a static branch.
* tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Move user_events.h temporarily out of include/uapi
ftrace: Make ftrace_graph_is_dead() a static branch
tracing: Set user_events to BROKEN
tracing/user_events: Remove eBPF interfaces
tracing/user_events: Hold event_mutex during dyn_event_add
proc: bootconfig: Add null pointer check
tracing: Rename the staging files for trace_events
|