| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This platform carries a HID compatible I2C touchscreen on the i2c4 bus,
but it may be at a different address, depending on the board model.
Add the node for a touchscreen at 0x10, but enable it only in the
final board dts.
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
This platform has a SPI NOR: enable support for it, completing the
storage compartment enablement for the entire platform.
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Nícolas F. R. A. Prado <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
All devices of the Cherry platform have a MT6360 sub-pmic,
providing two LDOs. Add the required node to enable the PMIC
but without regulators yet, as these will be added in a
later commit.
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Nícolas F. R. A. Prado <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add USB functionality by enabling the required PHYs and the XHCI
controllers.
This enables all of the supported USB ports on the Cherry boards.
Please note that u3phy1 also enables u3port1, which is configured
to be a PCI-Express PHY for the second PCIe controller that is
found on the MT8195 SoC, which will be enabled in a later commit.
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Nícolas F. R. A. Prado <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
This platform uses eight I2C controllers and one SPI controller:
in preparation for enabling devices attached to these controllers,
add basic configuration to enable the busses.
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Nícolas F. R. A. Prado <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add gpio-line-names to document GPIO names and add the default basic
pin configuration to allow lower power operation by setting appropriate
state on the unused pins.
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Nícolas F. R. A. Prado <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add mtk-sd controller and pin configuration to enable the internal
eMMC storage: now it is possible to mount a rootfs located at the
internal storage.
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Nícolas F. R. A. Prado <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
To allow MT6359 peripherals to trigger interrupts and the driver to
safely handle them, assign the right interrupt line for the Cherry
platform to the MT6359 PMIC node.
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Nícolas F. R. A. Prado <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add the regulators layout for this platform, including the basic power
rails controlled by the EC (and/or always on).
Moreover, include the MT6359 PMIC devicetree and add some configuration
for its regulators, essential to keep the machine alive after booting.
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Nícolas F. R. A. Prado <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Introduce the MT8195 Cherry Chromebook platform, including three
revisions of Cherry Tomato boards.
This basic configuration allows to boot Linux on all board revisions
and get a serial console from a ramdisk.
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Document board compatibles for the MT8195 Cherry platform's
Tomato Chromebooks, at the time of writing composed of four
revisions (r1, r2, r3-r4).
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add support for the SPI NOR flash memory present on the Asurada
platform.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Enable support for the SCP co-processor present on MT8192. It is used
as part of the video encoding and decoding processes.
A region of memory is carved out for its use, and remoteproc setup for
communication with the ChromeOS EC.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Enable both MMC controllers present on Asurada. MMC0 is for
non-removable internal memory, while MMC1 is an SD card slot. MMC1 isn't
used on all machines, but in those cases the CD interrupt is never
triggered and thus it is basically as if it was disabled.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
The Asurada platform uses regulators from MT6315 PMICs acessible through
SPMI. Add support for them.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
MT6359 is the primary PMIC present on the Asurada platform. Include its
dtsi and configure properties specific for the platform.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Enable MT8192's PCIe controller and add support for the MT7921e WiFi
card that is present on that bus for the Asurada platform.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Enable XHCI controller on the Asurada platform. This allows the use of
the USB ports, and therefore a rootfs can be loaded and a usable shell
reached from a live USB image.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
The Spherion board has keyboard backlight controlled by the PWM signal
generated by the ChromeOS EC.
Enable PWM output for ChromeOS EC and add a PWM controlled LED node for
the keyboard backlight.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
All machines of the Asurada platform have a touchscreen at address 0x10
in the I2C0 bus, but the devices vary: Spherion has the Elan eKTH3500
touchscreen, while Hayato has a generic HID-over-i2c touchscreen.
Add common support for the touchscreens on the platform and the
specifics in each board file.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add support for the Elan eKTH3000 i2c trackpad present on Asurada. It is
connected to the I2C2 bus and has address 0x15.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
The Asurada platform has a Google Security Chip connected to the SPI5
bus. It runs the cr50 firmware and provides TPM functionality. Add
support for it.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Chromebooks' embedded keyboards differ from standard layouts for the
top row in that they have shortcuts in place of the standard function
keys. Map these keys to achieve the functionality that is pictured on
the printouts.
There's a minor difference between the keys present on Hayato, which
uses an older layout, and Spherion, which uses a newer one.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add support for the ChromeOS Embedded Controller present on the Asurada
platform. It is connected through the SPI1 bus and offers several
functionalities: base detection, PWM controller, I2C tunneling,
regulators, Type-C connector management, keyboard and Smart Battery
Metrics (SBS).
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
The Asurada platform has five I2C controllers and two SPI controllers
that are used. In preparation for enabling the devices connected to
these controllers, enable and configure their busses.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add system-wide power supplies present on all of the boards in the
Asurada family.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add the gpio-line-names property to gpio-controller in order to
document the usage of GPIOs on the Asurada platform.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Introduce the MT8192 Asurada Chromebook platform, including the Asurada
Spherion and Asurada Hayato boards.
This is enough configuration to get serial output working on Spherion
and Hayato.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add binding for the Google Hayato board.
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Acked-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add binding for the Google Spherion board, which is used for Acer
Chromebook 514 (CB514-2H).
Signed-off-by: Nícolas F. R. A. Prado <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Acked-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add a phandle to the MT8183_POWER_DOMAIN_MFG_ASYNC power domain and
assign the GPU VSRAM supply to this in mt8183-kukui: this allows to
keep the sram powered up while the GPU is used.
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
The Draak and Ebisu boards support an optional LVDS panel. One
compatible panel is the Mitsubishi AA104XD12. Add a corresponding DT
overlay.
Signed-off-by: Laurent Pinchart <[email protected]>
Reviewed-by: Kieran Bingham <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
The Salvator-X and Salvator-XS boards support an optional LVDS panel.
One compatible panel is the Mitsubishi AA104XD12. Add a corresponding DT
overlay.
Signed-off-by: Laurent Pinchart <[email protected]>
Reviewed-by: Kieran Bingham <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
The Mitsubishi AA1024XD12 panel can be used for R-Car Gen2 and Gen3
boards as an optional external panel. It is described in the
arm/boot/dts/r8a77xx-aa104xd12-panel.dtsi file as a direct child of the
DT root node. This allows including r8a77xx-aa104xd12-panel.dtsi in
board device trees, with other minor modifications, to enable the panel.
This is however not how external components should be modelled. Instead
of modifying the board device tree to enable the panel, it should be
compiled as a DT overlay, to be loaded by the boot loader.
Prepare the r8a77xx-aa104xd12-panel.dtsi file for this usage by
declaring a panel node only, without hardcoding its path. Overlay
sources can then include r8a77xx-aa104xd12-panel.dtsi where appropriate.
This change doesn't cause any regression as r8a77xx-aa104xd12-panel.dtsi
is currently unused. As overlay support for this panel has only been
tested with Gen3 hardware, and Gen2 support will require more
development, move the file to arch/arm64/boot/dts/renesas/.
Signed-off-by: Laurent Pinchart <[email protected]>
Reviewed-by: Kieran Bingham <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
Group devices like Chip ID or SoC information under "hwinfo" directory.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.20, part two
1. Correct SPI11 pin names on ExynosAutov9.
2. Add more USI (I2C/SPI/UART) devices to ExynosAutov9.
* tag 'samsung-dt64-5.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynosautov9: add usi device tree nodes
arm64: dts: exynosautov9: prepare usi0 changes
arm64: dts: exynosautov9: add pdma0 device tree node
dt-bindings: soc: samsung: usi: add exynosautov9-usi compatible
arm64: dts: exynosautov9: correct spi11 pin names
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.20, part two
1. Cleanups: align SDHCI node names.
2. DT bindings: Document preferred compatible naming schema.
3. DT bindings: fixes and improvements to Exynos PMU bindings.
* tag 'samsung-dt-5.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: soc: samsung: exynos-pmu: add reboot-mode
dt-bindings: soc: samsung: exynos-pmu: use abolute ref paths
dt-bindings: soc: samsung: exynos-pmu: cleanup assigned clocks
dt-bindings: samsung: document preferred compatible naming
ARM: dts: s5pv210: align SDHCI node name with dtschema
ARM: dts: s3c64xx: align SDHCI node name with dtschema
ARM: dts: s3c24xx: align SDHCI node name with dtschema
ARM: dts: exynos: align SDHCI node name with dtschema
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Clean up the PCIe PHY node by renaming the wrapper node and grouping the
child node properties.
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Clean up the PCIe PHY nodes by using a non-empty ranges property.
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The QMP UFS PHY provides more than one symbol clock and would need an
index to differentiate the clocks, but none of this is described by the
binding currently.
Drop the incorrect '#clock-cells' property for now.
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The QMP UFS PHY provides more than one symbol clock and would need an
index to differentiate the clocks, but none of this is described by the
binding currently.
Drop the incorrect '#clock-cells' property for now.
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The QMP UFS PHY provides more than one symbol clock and would need an
index to differentiate the clocks, but none of this is described by the
binding currently.
Drop the incorrect '#clock-cells' property for now.
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The QMP USB PHY provides a single clock so drop the redundant clock
index.
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The QMP USB PHY provides a single clock so drop the redundant clock
index.
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The QMP USB PHY provides a single clock so drop the redundant clock
index.
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The QMP USB PHY provides a single clock so drop the redundant clock
index.
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The QMP USB PHY provides a single clock so drop the redundant clock
index.
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add the missing '#clock-cells' properties to the PCIe QMP PHY nodes.
Signed-off-by: Johan Hovold <[email protected]>
Fixes: e53bdfc00977 ("arm64: dts: qcom: sm8250: Add PCIe support")
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The QMP PCIe PHY provides a single clock so drop the redundant clock
index.
Signed-off-by: Johan Hovold <[email protected]>
Fixes: bd7d507935ca ("arm64: dts: qcom: sc7280: Add pcie clock support")
Fixes: 92e0ee9f83b3 ("arm64: dts: qcom: sc7280: Add PCIe and PHY related nodes")
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This reverts commit afcbe252e9c19161e4d4c95f33faaf592f1de086.
The commit in question caused my sc7280-herobrine-herobrine-r1 board
not to boot anymore. This shouldn't be too surprising since the driver
is relying on the name "cqhci".
The issue seems to be that someone decided to change the names of
things when the binding moved from .txt to .yaml. We should go back to
the names that the bindings have historically specified.
For some history, see commit d3392339cae9 ("mmc: cqhci: Update cqhci
memory ioresource name") and commit d79100c91ae5 ("dt-bindings: mmc:
sdhci-msm: Add CQE reg map").
Fixes: afcbe252e9c1 ("arm64: dts: qcom: Fix 'reg-names' for sdhci nodes")
Signed-off-by: Douglas Anderson <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/20220706144706.1.I48f35820bf3670d54940110462555c2d0a6d5eb2@changeid
|