| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 5f300acd8ae9f3d4585154370012ffc5c665330f
(ARM: 7152/1: distclean: Remove generated .dtb files)
ensured that dtbs were cleaned up when they were in
arch/arm/boot.
However, with the following commit:
commit 499cd8298628eeabf0eb5eb6525d4faa0eec80d8
(ARM: dt: change .dtb build rules to build in dts directory)
make clean now leaves dtbs in arch/arm/boot/dts/
untouched. Include dts directory so that clean-files rule
from arch/arm/boot/dts/Makefile is invoked when make
clean is done.
Cc: Dirk Behme <[email protected]>
CC: Grant Likely <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
BCM2835-ARM-Peripherals.pdf states that the I2C module's input clock is
nominally 150MHz, and that value is currently reflected in bcm2835.dtsi.
However, practical measurements show that the rate is actually 250MHz,
and this agrees with various downstream kernels.
Switch the I2C clock's frequency to 250MHz so that the generated bus
clock rate is accurate.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
In b1cffebf (ARM: GIC: remove direct use of gic_raise_softirq)
gic_raise_softirq() was moved inside arch/arm/common/gic.c but in the
process it reverted by mistake a change to that function made by
384a290 (ARM: gic: use a private mapping for CPU target interfaces).
This breaks multicluster systems on ARM.
This patch fixes the typo.
Signed-off-by: Javi Merino <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
This patch (as1661) fixes a rather obscure bug in ehci-hcd. In a
couple of places, the driver compares the DMA address stored in a QH's
overlay region with the address of a particular qTD, in order to see
whether that qTD is the one currently being processed by the hardware.
(If it is then the status in the QH's overlay region is more
up-to-date than the status in the qTD, and if it isn't then the
overlay's value needs to be adjusted when the QH is added back to the
active schedule.)
However, DMA address in the overlay region isn't always valid. It
sometimes will contain a stale value, which may happen by coincidence
to be equal to a qTD's DMA address. Instead of checking the DMA
address, we should check whether the overlay region is active and
valid. The patch tests the ACTIVE bit in the overlay, and clears this
bit when the overlay becomes invalid (which happens when the
currently-executing URB is unlinked).
This is the second part of a fix for the regression reported at:
https://bugs.launchpad.net/bugs/1088733
Signed-off-by: Alan Stern <[email protected]>
Reported-by: Joseph Salisbury <[email protected]>
Reported-and-tested-by: Stephen Thirlwall <[email protected]>
CC: <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch (as1660) works around a hardware problem present in some
(if not all) Intel EHCI controllers. After a QH has been unlinked
from the async schedule and the corresponding IAA interrupt has
occurred, the controller is not supposed access the QH and its qTDs.
There certainly shouldn't be any more DMA writes to those structures.
Nevertheless, Intel's controllers have been observed to perform a
final writeback to the QH's overlay region and to the most recent qTD.
For more information and a test program to determine whether this
problem is present in a particular controller, see
http://marc.info/?l=linux-usb&m=135492071812265&w=2
http://marc.info/?l=linux-usb&m=136182570800963&w=2
This patch works around the problem by always waiting for two IAA
cycles when unlinking an async QH. The extra IAA delay gives the
controller time to perform its final writeback.
Surprisingly enough, the effects of this silicon bug have gone
undetected until quite recently. More through luck than anything
else, it hasn't caused any apparent problems. However, it does
interact badly with the path that follows this one, so it needs to be
addressed.
This is the first part of a fix for the regression reported at:
https://bugs.launchpad.net/bugs/1088733
Signed-off-by: Alan Stern <[email protected]>
Tested-by: Stephen Thirlwall <[email protected]>
CC: <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
"usb: fixes for v3.9-rc2
A few drivers got their gadget->dev registration problems
exposed by the removal of ->start()/->stop() functions from
udc-core.c. All of such instances are now fixed.
We're also fixing chipidea's mistake of registering private
debugging sysfs files under the gadget's device. This is
in preparation to complete removal of gadget->dev handling
from all UDC drivers which will happen for v3.10 merge window.
MUSB's Kconfig got a fix to avoid a non-buildable selection
of its Kconfig choices.
Some extra devm_ioremap_resource() are added here because they
missed the merge window.
Finally, we have a temporary fix linking function drivers
before gadget drivers so they work fine when they're statically
linked to the kernel. We've done it so since the real fix wouldn't
fit the -rc cycle."
|
|
virtio_rng feeds the randomness buffer handed by the core directly
into the scatterlist, since commit bb347d98079a547e80bd4722dee1de61e4dca0e8.
However, if CONFIG_HW_RANDOM=m, the static buffer isn't a linear address
(at least on most archs). We could fix this in virtio_rng, but it's actually
far easier to just do it in the core as virtio_rng would have to allocate
a buffer every time (it doesn't know how much the core will want to read).
Reported-by: Aurelien Jarno <[email protected]>
Tested-by: Aurelien Jarno <[email protected]>
Signed-off-by: Rusty Russell <[email protected]>
Cc: [email protected]
|
|
Commit 5ac00add added a testnset mutex and code that disallows
running administrative tasks in parallel. It is prevented that
the device add/delete/balance/replace/resize operations are
started in parallel. By mistake, the defragmentation operation
was included in the check for mutually exclusiveness as well.
This is fixed with this commit.
Signed-off-by: Stefan Behrens <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
|
|
Only let one trans handle to wait for other handles, otherwise we
will get ABBA issues.
Signed-off-by: Liu Bo <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
|
|
Btrfs balance can easily hit BUG_ON in these places, but we want
to it bail out gracefully after we force the whole filesystem to
readonly. So we use btrfs_std_error hook in place of BUG_ON.
Signed-off-by: Liu Bo <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
|
|
We can bail out from here gracefully instead of a cold BUG_ON.
Signed-off-by: Liu Bo <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
|
|
We've missed the 'free blocks' part on ENOMEM error.
Signed-off-by: Liu Bo <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
|
|
We first use btrfs_std_error hook to replace with BUG_ON, and we
also need to cleanup what is left, including reloc roots rbtree
and reloc roots list.
Here we use a helper function to cleanup both rbtree and list, and
since this function can also be used in the balance recover path,
we also make the change as well to keep code simple.
Signed-off-by: Liu Bo <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
|
|
Add a check for NULL pointer to avoid invalid reference.
Signed-off-by: Liu Bo <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
|
|
commitment fails
If the async transaction commitment failed, we need close the
current transaction handler, or the current transaction will be
blocked to commit because of this orphan handler.
We fix the problem by doing sync transaction commitment, that is
to invoke btrfs_commit_transaction().
Signed-off-by: Miao Xie <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
|
|
There are several bugs at error path of create_snapshot() when the
transaction commitment failed.
- access the freed transaction handler. At the end of the
transaction commitment, the transaction handler was freed, so we
should not access it after the transaction commitment.
- we were not aware of the error which happened during the snapshot
creation if we submitted a async transaction commitment.
- pending snapshot access vs pending snapshot free. when something
wrong happened after we submitted a async transaction commitment,
the transaction committer would cleanup the pending snapshots and
free them. But the snapshot creators were not aware of it, they
would access the freed pending snapshots.
This patch fixes the above problems by:
- remove the dangerous code that accessed the freed handler
- assign ->error if the error happens during the snapshot creation
- the transaction committer doesn't free the pending snapshots,
just assigns the error number and evicts them before we unblock
the transaction.
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Miao Xie <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
|
|
We need to inc the nlink of deleted entries when running replay so we can do the
unlink on the fs_root and get everything cleaned up and then have the orphan
cleanup do the right thing. The problem is inc_nlink complains about this, even
thought it still does the right thing. So use set_nlink() if our i_nlink is 0
to keep users from seeing the warnings during log replay. Thanks,
Signed-off-by: Josef Bacik <[email protected]>
|
|
Commit bbd707ac {ARM: omap2: use machine specific hook for late init}
accidentally added two declarations for omap4430_init_late().
Remove the duplicate declaration.
Cc: Shawn Guo <[email protected]>
Signed-off-by: Santosh Shilimkar <[email protected]>
Reviewed-by: Felipe Balbi <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
This is needed because the omap_mux_get_by_name()
function calls the _omap_mux_get_by_name subfunction
for each mux partition until needed mux is not found.
As a result, we get messages like
"Could not find signal XXX" for each partition
where this mux name does not exist.
This patch fixes wrong error message in
the _omap_mux_get_by_name() function moving it
to the omap_mux_get_by_name() one and as result
reduces noise in the kernel log.
My kernel log without this patch:
[...]
[ 0.221801] omap_mux_init: Add partition: #2: wkup, flags: 3
[ 0.222045] _omap_mux_get_by_name: Could not find signal fref_clk0_out.sys_drm_msecure
[ 0.222137] _omap_mux_get_by_name: Could not find signal sys_nirq
[ 0.222167] _omap_mux_get_by_name: Could not find signal sys_nirq
[ 0.225006] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[ 0.225006] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[ 0.270111] _omap_mux_get_by_name: Could not find signal fref_clk4_out.fref_clk4_out
[ 0.273406] twl: not initialized
[...]
My kernel log with this patch:
[...]
[ 0.221771] omap_mux_init: Add partition: #2: wkup, flags: 3
[ 0.222106] omap_mux_get_by_name: Could not find signal sys_nirq
[ 0.224945] omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[ 0.274536] twl: not initialized
[...]
Signed-off-by: Ruslan Bilovol <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
|
|
OMAP's debugfs interface creates one file
for each signal in the mux table, such file
provides a read method but didn't provide
read permission. Fix it.
Signed-off-by: Felipe Balbi <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
We should not select drivers from kconfig as they should by default
be optional. Otherwise we'll be chasing broken dependencies forever:
warning: (MACH_OMAP_ZOOM2 && MACH_OMAP_ZOOM3 && MWAVE) selects SERIAL_8250
which has unmet direct dependencies (TTY && HAS_IOMEM && GENERIC_HARDIRQS)
Fix the issue by removing the selects for zoom and add them to
omap2plus_defconfig.
Reported-by: Russell King <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
The .init_late callback for OMAP3 has been missing for DT
builds, which causes a lot of late PM initializations to
be missed in turn.
Signed-off-by: Rajendra Nayak <[email protected]>
Acked-by: Santosh Shilimkar <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
Commit 6797b4fe (ARM: OMAP2+: Prevent potential crash if GPMC probe fails)
added code to ensure that GPMC chip-selects could not be requested until the
device probe was successful. The chip-selects should have been
unreserved at the end of the probe function, but the code to unreserve
them appears to have ended up in the gpmc_calc_timings() function and
hence, this is causing problems requesting chip-selects. Fix this merge
error by unreserving the chip-selects at the end of the probe, but
before we call the gpmc child probe functions (for device-tree) which
request a chip-select.
Signed-off-by: Jon Hunter <[email protected]>
Tested-by: Ezequiel Garcia <[email protected]>
Tested-by: Philip Avinash <[email protected]>
Tested-by: Grazvydas Ignotas <[email protected]>
[[email protected]: updated description to add breaking commit id]
Signed-off-by: Tony Lindgren <[email protected]>
|
|
Commit 16559ae4 (kgdb: remove #include <linux/serial_8250.h> from kgdb.h)
had a side effect of breaking omap1_defconfig build as some headers
were included indirectly:
arch/arm/mach-omap1/board-h2.c:249: error: ‘INT_KEYBOARD’ undeclared here (not in a function)
...
This worked earlier as linux/serial_8250.h included linux/serial_core.h,
via linux/serial_8250.h from linux/kgdb.h. Fix this by including the
necessary headers directly.
Signed-off-by: Tony Lindgren <[email protected]>
|
|
We should not update ts_recent and call tcp_rcv_rtt_measure_ts() both
before and after going to step5. That wastes CPU and double-counts the
receiver-side RTT sample.
Signed-off-by: Neal Cardwell <[email protected]>
Acked-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This fixes the following sparse warning:
net/caif/caif_usb.c:84:16: warning: symbol 'cfusbl_create' was not
declared. Should it be static?
Signed-off-by: Silviu-Mihai Popescu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Cc: David S. Miller <[email protected]>
Cc: Venkat Venkatsubra <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
build error cause by
Commit ff43da86c69d76a726ffe7d1666148960dc1d108
("NET: FEC: dynamtic check DMA desc buff type")
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_nextdesc’:
drivers/net/ethernet/freescale/fec.c:215:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_prevdesc’:
drivers/net/ethernet/freescale/fec.c:224:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_start_xmit’:
drivers/net/ethernet/freescale/fec.c:286:37: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:287:13: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:324:7: error: dereferencing pointer to incomplete type etc....
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Setting net.ipv6.conf.<interface>.accept_ra=2 causes the kernel
to accept RAs even when forwarding is enabled. However, enabling
forwarding purges all default routes on the system, breaking
connectivity until the next RA is received. Fix this by not
purging default routes on interfaces that have accept_ra=2.
Signed-off-by: Lorenzo Colitti <[email protected]>
Acked-by: YOSHIFUJI Hideaki <[email protected]>
Acked-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
up stack ndo_start_xmit already hold lock.
fec_enet_start_xmit needn't spin lock.
stat_xmit just update fep->cur_tx
fec_enet_tx just update fep->dirty_tx
Reserve a empty bdb to check full or empty
cur_tx == dirty_tx means full
cur_tx == dirty_tx +1 means empty
So needn't is_full variable.
Fix spin lock deadlock
=================================
[ INFO: inconsistent lock state ]
3.8.0-rc5+ #107 Not tainted
---------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
ptp4l/615 [HC1[1]:SC0[0]:HE0:SE1] takes:
(&(&list->lock)->rlock#3){?.-...}, at: [<8042c3c4>] skb_queue_tail+0x20/0x50
{HARDIRQ-ON-W} state was registered at:
[<80067250>] mark_lock+0x154/0x4e8
[<800676f4>] mark_irqflags+0x110/0x1a4
[<80069208>] __lock_acquire+0x494/0x9c0
[<80069ce8>] lock_acquire+0x90/0xa4
[<80527ad0>] _raw_spin_lock_bh+0x44/0x54
[<804877e0>] first_packet_length+0x38/0x1f0
[<804879e4>] udp_poll+0x4c/0x5c
[<804231f8>] sock_poll+0x24/0x28
[<800d27f0>] do_poll.isra.10+0x120/0x254
[<800d36e4>] do_sys_poll+0x15c/0x1e8
[<800d3828>] sys_poll+0x60/0xc8
[<8000e780>] ret_fast_syscall+0x0/0x3c
*** DEADLOCK ***
1 lock held by ptp4l/615:
#0: (&(&fep->hw_lock)->rlock){-.-...}, at: [<80355f9c>] fec_enet_tx+0x24/0x268
stack backtrace:
Backtrace:
[<800121e0>] (dump_backtrace+0x0/0x10c) from [<80516210>] (dump_stack+0x18/0x1c)
r6:8063b1fc r5:bf38b2f8 r4:bf38b000 r3:bf38b000
[<805161f8>] (dump_stack+0x0/0x1c) from [<805189d0>] (print_usage_bug.part.34+0x164/0x1a4)
[<8051886c>] (print_usage_bug.part.34+0x0/0x1a4) from [<80518a88>] (print_usage_bug+0x78/0x88)
r8:80065664 r7:bf38b2f8 r6:00000002 r5:00000000 r4:bf38b000
[<80518a10>] (print_usage_bug+0x0/0x88) from [<80518b58>] (mark_lock_irq+0xc0/0x270)
r7:bf38b000 r6:00000002 r5:bf38b2f8 r4:00000000
[<80518a98>] (mark_lock_irq+0x0/0x270) from [<80067270>] (mark_lock+0x174/0x4e8)
[<800670fc>] (mark_lock+0x0/0x4e8) from [<80067744>] (mark_irqflags+0x160/0x1a4)
[<800675e4>] (mark_irqflags+0x0/0x1a4) from [<80069208>] (__lock_acquire+0x494/0x9c0)
r5:00000002 r4:bf38b2f8
[<80068d74>] (__lock_acquire+0x0/0x9c0) from [<80069ce8>] (lock_acquire+0x90/0xa4)
[<80069c58>] (lock_acquire+0x0/0xa4) from [<805278d8>] (_raw_spin_lock_irqsave+0x4c/0x60)
[<8052788c>] (_raw_spin_lock_irqsave+0x0/0x60) from [<8042c3c4>] (skb_queue_tail+0x20/0x50)
r6:bfbb2180 r5:bf1d0190 r4:bf1d0184
[<8042c3a4>] (skb_queue_tail+0x0/0x50) from [<8042c4cc>] (sock_queue_err_skb+0xd8/0x188)
r6:00000056 r5:bfbb2180 r4:bf1d0000 r3:00000000
[<8042c3f4>] (sock_queue_err_skb+0x0/0x188) from [<8042d15c>] (skb_tstamp_tx+0x70/0xa0)
r6:bf0dddb0 r5:bf1d0000 r4:bfbb2180 r3:00000004
[<8042d0ec>] (skb_tstamp_tx+0x0/0xa0) from [<803561d0>] (fec_enet_tx+0x258/0x268)
r6:c089d260 r5:00001c00 r4:bfbd0000
[<80355f78>] (fec_enet_tx+0x0/0x268) from [<803562cc>] (fec_enet_interrupt+0xec/0xf8)
[<803561e0>] (fec_enet_interrupt+0x0/0xf8) from [<8007d5b0>] (handle_irq_event_percpu+0x54/0x1a0)
[<8007d55c>] (handle_irq_event_percpu+0x0/0x1a0) from [<8007d740>] (handle_irq_event+0x44/0x64)
[<8007d6fc>] (handle_irq_event+0x0/0x64) from [<80080690>] (handle_fasteoi_irq+0xc4/0x15c)
r6:bf0dc000 r5:bf811290 r4:bf811240 r3:00000000
[<800805cc>] (handle_fasteoi_irq+0x0/0x15c) from [<8007ceec>] (generic_handle_irq+0x28/0x38)
r5:807130c8 r4:00000096
[<8007cec4>] (generic_handle_irq+0x0/0x38) from [<8000f16c>] (handle_IRQ+0x54/0xb4)
r4:8071d280 r3:00000180
[<8000f118>] (handle_IRQ+0x0/0xb4) from [<80008544>] (gic_handle_irq+0x30/0x64)
r8:8000e924 r7:f4000100 r6:bf0ddef8 r5:8071c974 r4:f400010c
r3:00000000
[<80008514>] (gic_handle_irq+0x0/0x64) from [<8000e2e4>] (__irq_svc+0x44/0x5c)
Exception stack(0xbf0ddef8 to 0xbf0ddf40)
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Don't definite its own MAX_KMALLOC_SIZE, use the one
defined in mm.
Cc: Vlad Yasevich <[email protected]>
Cc: Sridhar Samudrala <[email protected]>
Cc: Neil Horman <[email protected]>
Cc: David S. Miller <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Acked-by: Neil Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Dave Jones reported the following bug:
"When fed mangled socket data, rds will trust what userspace gives it,
and tries to allocate enormous amounts of memory larger than what
kmalloc can satisfy."
WARNING: at mm/page_alloc.c:2393 __alloc_pages_nodemask+0xa0d/0xbe0()
Hardware name: GA-MA78GM-S2H
Modules linked in: vmw_vsock_vmci_transport vmw_vmci vsock fuse bnep dlci bridge 8021q garp stp mrp binfmt_misc l2tp_ppp l2tp_core rfcomm s
Pid: 24652, comm: trinity-child2 Not tainted 3.8.0+ #65
Call Trace:
[<ffffffff81044155>] warn_slowpath_common+0x75/0xa0
[<ffffffff8104419a>] warn_slowpath_null+0x1a/0x20
[<ffffffff811444ad>] __alloc_pages_nodemask+0xa0d/0xbe0
[<ffffffff8100a196>] ? native_sched_clock+0x26/0x90
[<ffffffff810b2128>] ? trace_hardirqs_off_caller+0x28/0xc0
[<ffffffff810b21cd>] ? trace_hardirqs_off+0xd/0x10
[<ffffffff811861f8>] alloc_pages_current+0xb8/0x180
[<ffffffff8113eaaa>] __get_free_pages+0x2a/0x80
[<ffffffff811934fe>] kmalloc_order_trace+0x3e/0x1a0
[<ffffffff81193955>] __kmalloc+0x2f5/0x3a0
[<ffffffff8104df0c>] ? local_bh_enable_ip+0x7c/0xf0
[<ffffffffa0401ab3>] rds_message_alloc+0x23/0xb0 [rds]
[<ffffffffa04043a1>] rds_sendmsg+0x2b1/0x990 [rds]
[<ffffffff810b21cd>] ? trace_hardirqs_off+0xd/0x10
[<ffffffff81564620>] sock_sendmsg+0xb0/0xe0
[<ffffffff810b2052>] ? get_lock_stats+0x22/0x70
[<ffffffff810b24be>] ? put_lock_stats.isra.23+0xe/0x40
[<ffffffff81567f30>] sys_sendto+0x130/0x180
[<ffffffff810b872d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff816c547b>] ? _raw_spin_unlock_irq+0x3b/0x60
[<ffffffff816cd767>] ? sysret_check+0x1b/0x56
[<ffffffff810b8695>] ? trace_hardirqs_on_caller+0x115/0x1a0
[<ffffffff81341d8e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff816cd742>] system_call_fastpath+0x16/0x1b
---[ end trace eed6ae990d018c8b ]---
Reported-by: Dave Jones <[email protected]>
Cc: Dave Jones <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Venkat Venkatsubra <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Acked-by: Venkat Venkatsubra <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This was pointed out by Al Viro. Using the correct wrappers
properly does sign extension as necessary on syscall arguments.
Signed-off-by: Chris Metcalf <[email protected]>
|
|
Commit 6133705494bb introduced a circular lock dependency because
posix_cpu_timers_exit() is called by release_task(), which is holding
a writer lock on tasklist_lock, and this can cause a deadlock since
kill_fasync() gets called with nonblocking_pool.lock taken.
There's no reason why kill_fasync() needs to be taken while the random
pool is locked, so move it out to fix this locking dependency.
Signed-off-by: "Theodore Ts'o" <[email protected]>
Reported-by: Russ Dill <[email protected]>
Cc: [email protected]
|
|
On G45 some low res modes (800x600 and 1024x768) produce a blank
screen when the display plane is enabled with with cursor plane
off.
Experiments showed that this issue occurred when the following
conditions were met:
a. a previous mode had the cursor plane enabled (Xserver).
b. this mode or the previous one was using self refresh. (Thus
the problem was only seen with low res modes).
The screens lit up as soon as the cursor plane got enabled.
Therefore the blank screen occurred only in console mode, not
when running an Xserver.
It also seemed to be necessary to disable self refresh while briefly
enabling the cursor plane.
Signed-off-by: Egbert Eich <[email protected]>
Bugzilla: https://bugs.freedesktop.org/attachment.cgi?bugid=61457
Acked-by: Chris Wilson <[email protected]>
[danvet: drop spurious whitespace change.]
Signed-off-by: Daniel Vetter <[email protected]>
|
|
sys_llseek should specify the high and low 32-bit seek values as "unsigned
int" but instead it specifies "unsigned long". Since compat syscall
arguments are always sign-extended on tile, this means that a seek value
of 0xffffffff will be incorrectly interpreted as a value of -1ULL.
To avoid the risk of breaking binary compatibility on architectures
that already use sys_llseek this way, we follow the same path as MIPS
and provide a wrapper override.
Signed-off-by: Chris Metcalf <[email protected]>
Cc: [email protected] [v3.6 onwards]
|
|
The "dev" variable could be out of bounds. Calling
snd_seq_oss_synth_is_valid() checks that it is is a valid device
which has been opened. We check this inside set_note_event() so
this function can't succeed without a valid "dev". But we need to
do the check earlier to prevent invalid dereferences and memory
corruption.
One call tree where "dev" could be out of bounds is:
-> snd_seq_oss_oob_user()
-> snd_seq_oss_process_event()
-> extended_event()
-> note_on_event()
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Since commit c14b78e7decd0d1d5add6a4604feb8609fe920a9 ("netfilter:
nfnetlink: add mutex per subsystem") building nefnetlink.o without
CONFIG_PROVE_RCU set, triggers this GCC warning:
net/netfilter/nfnetlink.c:65:22: warning: ‘nfnl_get_lock’ defined but not used [-Wunused-function]
The cause of that warning is, in short, that rcu_lockdep_assert()
compiles away if CONFIG_PROVE_RCU is not set. Silence this warning by
open coding nfnl_get_lock() in the sole place it was called, which
allows to remove that function.
Signed-off-by: Paul Bolle <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
We should stop generting audit log if audit is disabled.
Signed-off-by: Gao feng <[email protected]>
Acked-by: Thomas Graf <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
After PCI and USB have stopped using the .find_bridge() callback in
struct acpi_bus_type, the only remaining user of it is SATA, but SATA
only pretends to be a user, because it points that callback to a stub
always returning -ENODEV.
For this reason, drop the SATA's dummy .find_bridge() callback and
remove .find_bridge(), which is not used any more, from struct
acpi_bus_type entirely.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Yinghai Lu <[email protected]>
Acked-by: Jeff Garzik <[email protected]>
|
|
USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.
What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.
To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Acked-by: Yinghai Lu <[email protected]>
Acked-by: Jeff Garzik <[email protected]>
|
|
pr->id is u32 which never < 0, so remove the redundant pr->id < 0
check from acpi_processor_add().
[rjw: Changelog]
Signed-off-by: Chen Gang <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
kfree() on a NULL pointer is a no-op, so remove a redundant NULL
pointer check in map_mat_entry().
[rjw: Changelog]
Signed-off-by: Syam Sidhardhan <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Got this dmesg log on an Acer Aspire 725.
[ 0.256351] ACPI: (supports S0ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130117/hwxface-568)
[ 0.256373] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130117/hwxface-568)
[ 0.256391] S3 S4 S5)
Avoid this interleaving error messages.
Signed-off-by: Joe Perches <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Device PM QoS sysfs attributes, if present during device removal,
are removed from within device_pm_remove(), which is too late,
since dpm_sysfs_remove() has already removed the whole attribute
group they belonged to. However, moving the removal of those
attributes to dpm_sysfs_remove() alone is not sufficient, because
in theory they still can be re-added right after being removed by it
(the device's driver is still bound to it at that point).
For this reason, move the entire desctruction of device PM QoS
constraints to dpm_sysfs_remove() and make it prevent any new
constraints from being added after it has run. Also, move the
initialization of the power.qos field in struct device to
device_pm_init_common() and drop the no longer needed
dev_pm_qos_constraints_init().
Reported-by: Sasha Levin <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
The current device PM QoS code assumes that certain functions will
never be called in parallel with each other (for example, it is
assumed that dev_pm_qos_expose_flags() won't be called in parallel
with dev_pm_qos_hide_flags() for the same device and analogously
for the latency limit), which may be overly optimistic. Moreover,
dev_pm_qos_expose_flags() and dev_pm_qos_expose_latency_limit()
leak memory in error code paths (req needs to be freed on errors)
and __dev_pm_qos_drop_user_request() forgets to free the request.
To fix the above issues put more things under the device PM QoS
mutex to make them mutually exclusive and add the missing freeing
of memory.
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
As uninitialized array members will be initialized to zero, we can
avoid using a for loop by setting a value to it.
Signed-off-by: Emilio López <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
Acked-By: Mark Langsdorf <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Make Operating Performance Points (OPP) library introductory chapter
a little more reader-friendly. Split the chapter into two sections,
highlight the definition with an example and minor rewording to be
verbose.
Reported-by: Linus Torvalds <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
Reviewed-by: Randy Dunlap <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|