| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Shutting down the RSB controller prevents communicating with a PMIC
inside pm_power_off(), since that gets called after device_shutdown(),
so it breaks system poweroff on some boards.
Reported-by: Ivaylo Dimitrov <[email protected]>
Tested-by: Ivaylo Dimitrov <[email protected]>
Acked-by: Jernej Skrabec <[email protected]>
Fixes: 843107498f91 ("bus: sunxi-rsb: Implement suspend/resume/shutdown callbacks")
Signed-off-by: Samuel Holland <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>
|
|
If the returning value of SMB2_set_info_init is an error-value,
exit the function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0967e5457954 ("cifs: use a compound for setting an xattr")
Signed-off-by: Anastasia Belova <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
Add LARA-L6 PIDs for three different USB compositions.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In default mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
In CDC-ECM mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <[email protected]>
[ johan: drop PID defines in favour of comments ]
Cc: [email protected]
Signed-off-by: Johan Hovold <[email protected]>
|
|
The official LARA-R6 (00B) modem uses 0x908b PID. LARA-R6 00B does not
implement a QMI interface on port 4, the reservation (RSVD(4)) has been
added to meet other companies that implement QMI on that interface.
LARA-R6 00B USB composition exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
Signed-off-by: Davide Tronchin <[email protected]>
Cc: [email protected]
Signed-off-by: Johan Hovold <[email protected]>
|
|
Remove the UBLOX_PRODUCT_R6XX 0x90fa association since LARA-R6 00B final
product uses a new USB composition with different PID. 0x90fa PID used
only by LARA-R6 internal prototypes.
Move 0x90fa PID directly in the option_ids array since used by other
Qualcomm based modem vendors as pointed out in:
https://lore.kernel.org/all/[email protected]
Signed-off-by: Davide Tronchin <[email protected]>
Cc: [email protected]
Signed-off-by: Johan Hovold <[email protected]>
|
|
pci_get_device() will increase the reference count for the returned
pci_dev. We need to use pci_dev_put() to decrease the reference count
before amd_probe() returns. There is no problem for the 'smbus_dev ==
NULL' branch because pci_dev_put() can also handle the NULL input
parameter case.
Fixes: 659c9bc114a8 ("mmc: sdhci-pci: Build o2micro support in the same module")
Signed-off-by: Xiongfeng Wang <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
I got a UAF report as following:
==================================================================
BUG: KASAN: use-after-free in __lock_acquire+0x935/0x2060
Read of size 8 at addr ffff88810e838220 by task python3/268
Call Trace:
<TASK>
dump_stack_lvl+0x67/0x83
print_report+0x178/0x4b0
kasan_report+0x90/0x190
__lock_acquire+0x935/0x2060
lock_acquire+0x156/0x400
_raw_spin_lock+0x2a/0x40
lockref_get+0x11/0x30
simple_recursive_removal+0x41/0x440
debugfs_remove.part.12+0x32/0x50
debugfs_remove+0x29/0x30
_regulator_put.cold.54+0x3e/0x27f
regulator_put+0x1f/0x30
release_nodes+0x6a/0xa0
devres_release_all+0xf8/0x150
Allocated by task 37:
kasan_save_stack+0x1c/0x40
kasan_set_track+0x21/0x30
__kasan_slab_alloc+0x5d/0x70
slab_post_alloc_hook+0x62/0x510
kmem_cache_alloc_lru+0x222/0x5a0
__d_alloc+0x31/0x440
d_alloc+0x30/0xf0
d_alloc_parallel+0xc4/0xd20
__lookup_slow+0x15e/0x2f0
lookup_one_len+0x13a/0x150
start_creating+0xea/0x190
debugfs_create_dir+0x1e/0x210
create_regulator+0x254/0x4e0
_regulator_get+0x2a1/0x467
_devm_regulator_get+0x5a/0xb0
regulator_virtual_probe+0xb9/0x1a0
Freed by task 30:
kasan_save_stack+0x1c/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x50
__kasan_slab_free+0x102/0x190
kmem_cache_free+0xf6/0x600
rcu_core+0x54c/0x12b0
__do_softirq+0xf2/0x5e3
Last potentially related work creation:
kasan_save_stack+0x1c/0x40
__kasan_record_aux_stack+0x98/0xb0
call_rcu+0x42/0x700
dentry_free+0x6c/0xd0
__dentry_kill+0x23b/0x2d0
dput.part.31+0x431/0x780
simple_recursive_removal+0xa9/0x440
debugfs_remove.part.12+0x32/0x50
debugfs_remove+0x29/0x30
regulator_unregister+0xe3/0x230
release_nodes+0x6a/0xa0
==================================================================
Here is how happened:
processor A processor B
regulator_register()
rdev_init_debugfs()
rdev->debugfs = debugfs_create_dir()
devm_regulator_get()
rdev = regulator_dev_lookup()
create_regulator(rdev)
// using rdev->debugfs as parent
debugfs_create_dir(rdev->debugfs)
mfd_remove_devices_fn()
release_nodes()
regulator_unregister()
// free rdev->debugfs
debugfs_remove_recursive(rdev->debugfs)
release_nodes()
destroy_regulator()
debugfs_remove_recursive() <- causes UAF
In devm_regulator_get(), after getting rdev, the refcount
is get, so fix this by moving debugfs_remove_recursive()
to regulator_dev_release(), then it can be proctected by
the refcount, the 'rdev->debugfs' can not be freed until
the refcount is 0.
Fixes: 5de705194e98 ("regulator: Add basic per consumer debugfs")
Signed-off-by: Yang Yingliang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
pci_get_device() will increase the reference count for the returned
pci_dev. Since 'dma_dev' is only used to filter the channel in
dw_spi_dma_chan_filer() after using it we need to call pci_dev_put() to
decrease the reference count. Also add pci_dev_put() for the error case.
Fixes: 7063c0d942a1 ("spi/dw_spi: add DMA support")
Signed-off-by: Xiongfeng Wang <[email protected]>
Acked-by: Serge Semin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
On embedded systems with little memory and no relevant
security concerns, it is beneficial to reduce the size
of the table.
Reducing the size from 2^16 to 2^8 saves 255 KiB
of kernel RAM.
Makes the table size configurable as an expert option.
The size was previously increased from 2^8 to 2^16
in commit 4c2c8f03a5ab ("tcp: increase source port perturb table to
2^16").
Signed-off-by: Gleb Mazovetskiy <[email protected]>
Reviewed-by: Kuniyuki Iwashima <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
timeout
The SD card is recognized failed sometimes when resume from suspend.
Because CD# debounce time too long then card present report wrong.
Finally, card is recognized failed.
Signed-off-by: Chevron Li <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
In mmc_select_voltage(), if there is no full power cycle, the voltage
range selected at the end of the function will be on a single range
(e.g. 3.3V/3.4V). To keep a range around the selected voltage (3.2V/3.4V),
the mask shift should be reduced by 1.
This issue was triggered by using a specific SD-card (Verbatim Premium
16GB UHS-1) on an STM32MP157C-DK2 board. This board cannot do UHS modes
and there is no power cycle. And the card was failing to switch to
high-speed mode. When adding the range 3.2V/3.3V for this card with the
proposed shift change, the card can switch to high-speed mode.
Fixes: ce69d37b7d8f ("mmc: core: Prevent violation of specs while initializing cards")
Signed-off-by: Yann Gautier <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
sk->sk_user_data has multiple users, which are not compatible with each
other. Writers must synchronize by grabbing the sk->sk_callback_lock.
l2tp currently fails to grab the lock when modifying the underlying tunnel
socket fields. Fix it by adding appropriate locking.
We err on the side of safety and grab the sk_callback_lock also inside the
sk_destruct callback overridden by l2tp, even though there should be no
refs allowing access to the sock at the time when sk_destruct gets called.
v4:
- serialize write to sk_user_data in l2tp sk_destruct
v3:
- switch from sock lock to sk_callback_lock
- document write-protection for sk_user_data
v2:
- update Fixes to point to origin of the bug
- use real names in Reported/Tested-by tags
Cc: Tom Parkin <[email protected]>
Fixes: 3557baabf280 ("[L2TP]: PPP over L2TP driver core")
Reported-by: Haowei Yan <[email protected]>
Signed-off-by: Jakub Sitnicki <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In case the requested bus clock is higher than the input clock, the correct
dividers (pre = 0, post = 0) are returned from mx51_ecspi_clkdiv(), but
*fres is left uninitialized and therefore contains an arbitrary value.
This causes trouble for the recently introduced PIO polling feature as the
value in spi_imx->spi_bus_clk is used there to calculate for which
transfers to enable PIO polling.
Fix this by setting *fres even if no clock dividers are in use.
This issue was observed on Kontron BL i.MX8MM with an SPI peripheral clock set
to 50 MHz by default and a requested SPI bus clock of 80 MHz for the SPI NOR
flash.
With the fix applied the debug message from mx51_ecspi_clkdiv() now prints the
following:
spi_imx 30820000.spi: mx51_ecspi_clkdiv: fin: 50000000, fspi: 50000000,
post: 0, pre: 0
Fixes: 6fd8b8503a0d ("spi: spi-imx: Fix out-of-order CS/SCLK operation at low speeds")
Fixes: 07e759387788 ("spi: spi-imx: add PIO polling support")
Cc: Marc Kleine-Budde <[email protected]>
Cc: David Jander <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Mark Brown <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: [email protected]
Signed-off-by: Frieder Schrempf <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
I got the following OOB report:
BUG: KASAN: slab-out-of-bounds in validate_desc+0xba/0x109
Read of size 8 at addr ffff888107db8ff0 by task python3/253
Call Trace:
<TASK>
dump_stack_lvl+0x67/0x83
print_report+0x178/0x4b0
kasan_report+0x90/0x190
validate_desc+0xba/0x109
gpiod_set_value_cansleep+0x40/0x5a
regulator_ena_gpio_ctrl+0x93/0xfc
_regulator_do_enable.cold.61+0x89/0x163
set_machine_constraints+0x140a/0x159c
regulator_register.cold.73+0x762/0x10cd
devm_regulator_register+0x57/0xb0
rt5759_probe+0x3a0/0x4ac [rt5759_regulator]
The desc used in validate_desc() is passed from 'reg_cfg.ena_gpiod',
which is not initialized. Fix this by initializing 'reg_cfg' to 0.
Fixes: 7b36ddb208bd ("regulator: rt5759: Add support for Richtek RT5759 DCDC converter")
Signed-off-by: Yang Yingliang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
regulator_register()
Here is a warning report about lack of registered release()
from kobject lib:
Device '(null)' does not have a release() function, it is broken and must be fixed.
WARNING: CPU: 0 PID: 48430 at drivers/base/core.c:2332 device_release+0x104/0x120
Call Trace:
kobject_put+0xdc/0x180
put_device+0x1b/0x30
regulator_register+0x651/0x1170
devm_regulator_register+0x4f/0xb0
When regulator_register() returns fail and directly goto `clean` symbol,
rdev->dev has not registered release() function yet (which is registered
by regulator_class in the following), so rdev needs to be freed manually.
If rdev->dev.of_node is not NULL, which means the of_node has gotten by
regulator_of_get_init_data(), it needs to call of_node_put() to avoid
refcount leak.
Otherwise, only calling put_device() would lead memory leak of rdev
in further:
unreferenced object 0xffff88810d0b1000 (size 2048):
comm "107-i2c-rtq6752", pid 48430, jiffies 4342258431 (age 1341.780s)
backtrace:
kmalloc_trace+0x22/0x110
regulator_register+0x184/0x1170
devm_regulator_register+0x4f/0xb0
When regulator_register() returns fail and goto `wash` symbol,
rdev->dev has registered release() function, so directly call
put_device() to cleanup everything.
Fixes: d3c731564e09 ("regulator: plug of_node leak in regulator_register()'s error path")
Signed-off-by: Zeng Heng <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
As the devm_kcalloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference.
Fixes: 349dd23931d1 ("ASoC: max98373: don't access volatile registers in bias level off")
Signed-off-by: Jiasheng Jiang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
transitions
Due to the hardware behavior, it takes some time for CBJ detection/impedance sensing/de-bounce.
The ClockStop_NotFinished flag will be raised until these functions are completed.
In ClockStopMode0 mode case, the SdW controller might check this flag from D3 to D0 when the
jack detection interrupt happened.
Signed-off-by: Shuming Fan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Commit 30de14b1884b ("s390: current_stack_pointer shouldn't be a
function") made current_stack_pointer a global register variable like
on many other architectures. Unfortunately on s390 it uncovers old
gcc bug which is fixed only since gcc-9.1 [gcc commit 3ad7fed1cc87
("S/390: Fix PR89775. Stackpointer save/restore instructions removed")]
and backported to gcc-8.4 and later. Due to this bug gcc versions prior
to 8.4 generate broken code which leads to stack corruptions.
Current minimal gcc version required to build the kernel is declared
as 5.1. It is not possible to fix all old gcc versions, so work
around this problem by avoiding using global register variable for
current_stack_pointer.
Fixes: 30de14b1884b ("s390: current_stack_pointer shouldn't be a function")
Reviewed-by: Heiko Carstens <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
After the rework from commit 1ebe2e5f9d68 ("block: remove
GENHD_FL_EXT_DEVT"), when calling device_add_disk(), dcssblk will end up
in disk_scan_partitions(), and not break out early w/o GENHD_FL_NO_PART.
This will trigger implicit open/release via blkdev_get/put_whole()
later. dcssblk_release() will then deadlock on dcssblk_devices_sem
semaphore, which is already held from dcssblk_add_store() when calling
device_add_disk().
dcssblk does not support partitions (DCSSBLK_MINORS_PER_DISK == 1), and
never scanned partitions before. Therefore restore the previous
behavior, and explicitly disallow partition scanning by setting the
GENHD_FL_NO_PART flag. This will also prevent this deadlock scenario.
Fixes: 1ebe2e5f9d68 ("block: remove GENHD_FL_EXT_DEVT")
Cc: <[email protected]> # 5.17+
Signed-off-by: Gerald Schaefer <[email protected]>
Acked-by: Heiko Carstens <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
.data.rel.ro* catches .data.rel.root_cpuacct, and the kernel crashes on
a store in css_clear_dir. At least we know read-only data protection is
working...
Fixes: b6adc6d6d3272 ("powerpc/build: move .data.rel.ro, .sdata2 to read-only")
Signed-off-by: Nicholas Piggin <[email protected]>
Reviewed-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Commit 1d1a0e7c5100 ("scripts/faddr2line: Fix overlapping text section
failures") can cause faddr2line to fail on ppc64le on some
distributions, while it works fine on other distributions. The failure
can be attributed to differences in the readelf output.
$ ./scripts/faddr2line vmlinux find_busiest_group+0x00
no match for find_busiest_group+0x00
On ppc64le, readelf adds the localentry tag before the symbol name on
some distributions, and adds the localentry tag after the symbol name on
other distributions. This problem has been discussed previously:
https://lore.kernel.org/bpf/20191211160133.GB4580@calabresa/
This problem can be overcome by filtering out the localentry tags in the
readelf output. Similar fixes are already present in the kernel by way
of the following commits:
1fd6cee127e2 ("libbpf: Fix VERSIONED_SYM_COUNT number parsing")
aa915931ac3e ("libbpf: Fix readelf output parsing for Fedora")
[jpoimboe: rework commit log]
Fixes: 1d1a0e7c5100 ("scripts/faddr2line: Fix overlapping text section failures")
Signed-off-by: Srikar Dronamraju <[email protected]>
Acked-by: Naveen N. Rao <[email protected]>
Reviewed-by: Thadeu Lima de Souza Cascardo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Josh Poimboeuf <[email protected]>
Signed-off-by: Peter Zijlstra <[email protected]>
|
|
A problem about insmod thunderbolt-net failed is triggered with following
log given while lsmod does not show thunderbolt_net:
insmod: ERROR: could not insert module thunderbolt-net.ko: File exists
The reason is that tbnet_init() returns tb_register_service_driver()
directly without checking its return value, if tb_register_service_driver()
failed, it returns without removing property directory, resulting the
property directory can never be created later.
tbnet_init()
tb_register_property_dir() # register property directory
tb_register_service_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without remove property directory
Fix by remove property directory when tb_register_service_driver() returns
error.
Fixes: e69b6c02b4c3 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Yuan Can <[email protected]>
Acked-by: Mika Westerberg <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When compiling linux 6.1.0-rc3 configured with CONFIG_64BIT=y and
CONFIG_PARAVIRT_SPINLOCKS=y on x86_64 using LLVM 11.0, an error:
"<inline asm> error: changed section flags for .spinlock.text,
expected:: 0x6" occurred.
The reason is the .spinlock.text in kernel/locking/qspinlock.o
is used many times, but its flags are omitted in subsequent use.
LLVM 11.0 assembler didn't permit to
leave out flags in subsequent uses of the same sections.
So this patch adds the corresponding flags to avoid above error.
Fixes: 501f7f69bca1 ("locking: Add __lockfunc to slow path functions")
Signed-off-by: Guo Jin <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Reviewed-by: Nathan Chancellor <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Deal with errata TGL052, ADL037 and RPL017 "Trace May Contain Incorrect
Data When Configured With Single Range Output Larger Than 4KB" by
disabling single range output whenever larger than 4KB.
Fixes: 670638477aed ("perf/x86/intel/pt: Opportunistically use single range output mode")
Signed-off-by: Adrian Hunter <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
throttling
amd_pmu_enable_all() does:
if (!test_bit(idx, cpuc->active_mask))
continue;
amd_pmu_enable_event(cpuc->events[idx]);
A perf NMI of another event can come between these two steps. Perf NMI
handler internally disables and enables _all_ events, including the one
which nmi-intercepted amd_pmu_enable_all() was in process of enabling.
If that unintentionally enabled event has very low sampling period and
causes immediate successive NMI, causing the event to be throttled,
cpuc->events[idx] and cpuc->active_mask gets cleared by x86_pmu_stop().
This will result in amd_pmu_enable_event() getting called with event=NULL
when amd_pmu_enable_all() resumes after handling the NMIs. This causes a
kernel crash:
BUG: kernel NULL pointer dereference, address: 0000000000000198
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
[...]
Call Trace:
<TASK>
amd_pmu_enable_all+0x68/0xb0
ctx_resched+0xd9/0x150
event_function+0xb8/0x130
? hrtimer_start_range_ns+0x141/0x4a0
? perf_duration_warn+0x30/0x30
remote_function+0x4d/0x60
__flush_smp_call_function_queue+0xc4/0x500
flush_smp_call_function_queue+0x11d/0x1b0
do_idle+0x18f/0x2d0
cpu_startup_entry+0x19/0x20
start_secondary+0x121/0x160
secondary_startup_64_no_verify+0xe5/0xeb
</TASK>
amd_pmu_disable_all()/amd_pmu_enable_all() calls inside perf NMI handler
were recently added as part of BRS enablement but I'm not sure whether
we really need them. We can just disable BRS in the beginning and enable
it back while returning from NMI. This will solve the issue by not
enabling those events whose active_masks are set but are not yet enabled
in hw pmu.
Fixes: ada543459cab ("perf/x86/amd: Add AMD Fam19h Branch Sampling support")
Reported-by: Linux Kernel Functional Testing <[email protected]>
Signed-off-by: Ravi Bangoria <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
Shang XiaoJing says:
====================
net: microchip: Fix potential null-ptr-deref due to create_singlethread_workqueue()
There are some functions call create_singlethread_workqueue() without
checking ret value, and the NULL workqueue_struct pointer may causes
null-ptr-deref. Will be fixed by this patch.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
and sparx5_start()
sparx_stats_init() calls create_singlethread_workqueue() and not
checked the ret value, which may return NULL. And a null-ptr-deref may
happen:
sparx_stats_init()
create_singlethread_workqueue() # failed, sparx5->stats_queue is NULL
queue_delayed_work()
queue_delayed_work_on()
__queue_delayed_work() # warning here, but continue
__queue_work() # access wq->flags, null-ptr-deref
Check the ret value and return -ENOMEM if it is NULL. So as
sparx5_start().
Fixes: af4b11022e2d ("net: sparx5: add ethtool configuration and statistics support")
Fixes: b37a1bae742f ("net: sparx5: add mactable support")
Signed-off-by: Shang XiaoJing <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
lan966x_stats_init() calls create_singlethread_workqueue() and not
checked the ret value, which may return NULL. And a null-ptr-deref may
happen:
lan966x_stats_init()
create_singlethread_workqueue() # failed, lan966x->stats_queue is NULL
queue_delayed_work()
queue_delayed_work_on()
__queue_delayed_work() # warning here, but continue
__queue_work() # access wq->flags, null-ptr-deref
Check the ret value and return -ENOMEM if it is NULL.
Fixes: 12c2d0a5b8e2 ("net: lan966x: add ethtool configuration and statistics")
Signed-off-by: Shang XiaoJing <[email protected]>
Reviewed-by: Horatiu Vultur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add module parameters to allow setting the hw_rfkill_switch and
set_fn_lock_led feature flags for testing these on laptops which are not
on the DMI-id based allow lists for these 2 flags.
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Yoga laptops
Commit 3ae86d2d4704 ("platform/x86: ideapad-laptop: Fix Legion 5 Fn lock
LED") uses the WMI event-id for the fn-lock event on some Legion 5 laptops
to manually toggle the fn-lock LED because the EC does not do it itself.
However, the same WMI ID is also sent on some Yoga laptops. Here, setting
the fn-lock state is not valid behavior, and causes the EC to spam
interrupts until the laptop is rebooted.
Add a set_fn_lock_led_list[] DMI-id list and only enable the workaround to
manually set the LED on models on this list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=212671
Cc: Meng Dong <[email protected]>
Signed-off-by: Arnav Rawat <[email protected]>
Link: https://lore.kernel.org/r/12093851.O9o76ZdvQC@fedora
[[email protected]: Check DMI-id list only once and store the result]
Signed-off-by: Hans de Goede <[email protected]>
|
|
Sometimes hp-wmi driver complains on system resume:
[ 483.116451] hp_wmi: Unknown event_id - 33 - 0x0
According to HP it's a feature called "HP Smart Experience App" and it's
safe to be ignored.
Signed-off-by: Kai-Heng Feng <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Add device nodes to enable support for battery and charger status, the
ACPI platform profile, as well as internal HID devices (including
touchpad and keyboard) on the Surface Laptop 5.
Signed-off-by: Maximilian Luz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Hans de Goede <[email protected]>
|
|
to_attr() in zonefs sysfs code is unused, which it causes a warning when
compiling with clang and W=1. Delete it to prevent the warning.
Signed-off-by: Damien Le Moal <[email protected]>
Reviewed-by: Johannes Thumshirn <[email protected]>
|
|
When an IO error occurs, the function __zonefs_io_error() is used to
issue a zone report to obtain the latest zone information from the
device. This function gets a zone report for all zones used as storage
for a file, which is always 1 zone except for files representing
aggregated conventional zones.
The number of zones of a zone report for a file is calculated in
__zonefs_io_error() by doing a bit-shift of the inode i_zone_size field,
which is equal to or larger than the device zone size. However, this
calculation does not take into account that the last zone of a zoned
device may be smaller than the zone size reported by bdev_zone_sectors()
(which is used to set the bit shift size). As a result, if an error
occurs for an IO targetting such last smaller zone, the zone report will
ask for 0 zones, leading to an invalid zone report.
Fix this by using the fact that all files require a 1 zone report,
except if the inode i_zone_size field indicates a zone size larger than
the device zone size. This exception case corresponds to a mount with
aggregated conventional zones.
A check for this exception is added to the file inode initialization
during mount. If an invalid setup is detected, emit an error and fail
the mount (check contributed by Johannes Thumshirn).
Signed-off-by: Johannes Thumshirn <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
|
|
The return value of CIFSGetExtAttr is negative, should be checked
with -EOPNOTSUPP rather than EOPNOTSUPP.
Fixes: 64a5cfa6db94 ("Allow setting per-file compression via SMB2/3")
Signed-off-by: Zhang Xiaoxu <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
When changing dhchap secrets we need to release the old
secrets as well.
kmemleak complaint:
--
unreferenced object 0xffff8c7f44ed8180 (size 64):
comm "check", pid 7304, jiffies 4295686133 (age 72034.246s)
hex dump (first 32 bytes):
44 48 48 43 2d 31 3a 30 30 3a 4c 64 4c 4f 64 71 DHHC-1:00:LdLOdq
79 56 69 67 77 48 55 32 6d 5a 59 4c 7a 35 59 38 yVigwHU2mZYLz5Y8
backtrace:
[<00000000b6fc5071>] kstrdup+0x2e/0x60
[<00000000f0f4633f>] 0xffffffffc0e07ee6
[<0000000053006c05>] 0xffffffffc0dff783
[<00000000419ae922>] configfs_write_iter+0xb1/0x120
[<000000008183c424>] vfs_write+0x2be/0x3c0
[<000000009005a2a5>] ksys_write+0x5f/0xe0
[<00000000cd495c89>] do_syscall_64+0x38/0x90
[<00000000f2a84ac5>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: db1312dd9548 ("nvmet: implement basic In-Band Authentication")
Signed-off-by: Sagi Grimberg <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
Added a quirk to fix the Netac NV7000 SSD reporting duplicate NGUIDs.
Cc: <[email protected]>
Signed-off-by: Tiago Dias Ferreira <[email protected]>
Reviewed-by: Chaitanya Kulkarni <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
Add patchwork URL for Kconfig and Kbuild.
Signed-off-by: Nicolas Schier <[email protected]>
Reviewed-by: Nick Desaulniers <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Remove Michal Marek from Kbuild maintainers as there is no response from him
since October 2017. Add an entry for Michal in CREDITS.
Michal, thanks for maintaining Kbuild for almost eight years!
Suggested-by: Nick Desaulniers <[email protected]>
Cc: Michal Marek <[email protected]>
Signed-off-by: Nicolas Schier <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
As suggested by Nick, add Nathan and myself to Kbuild reviewers to share more
review responsibilities.
Signed-off-by: Nicolas Schier <[email protected]>
Acked-by: Nick Desaulniers <[email protected]>
Acked-by: Nathan Chancellor <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
In the initial commit dc452a471dba ("net: dsa: introduce tagger-owned
storage for private and shared data"), we had a call to
tag_ops->disconnect(dst) issued from dsa_tree_free(), which is called at
tree teardown time.
There were problems with connecting to a switch tree as a whole, so this
got reworked to connecting to individual switches within the tree. In
this process, tag_ops->disconnect(ds) was made to be called only from
switch.c (cross-chip notifiers emitted as a result of dynamic tag proto
changes), but the normal driver teardown code path wasn't replaced with
anything.
Solve this problem by adding a function that does the opposite of
dsa_switch_setup_tag_protocol(), which is called from the equivalent
spot in dsa_switch_teardown(). The positioning here also ensures that we
won't have any use-after-free in tagging protocol (*rcv) ops, since the
teardown sequence is as follows:
dsa_tree_teardown
-> dsa_tree_teardown_master
-> dsa_master_teardown
-> unsets master->dsa_ptr, making no further packets match the
ETH_P_XDSA packet type handler
-> dsa_tree_teardown_ports
-> dsa_port_teardown
-> dsa_slave_destroy
-> unregisters DSA net devices, there is even a synchronize_net()
in unregister_netdevice_many()
-> dsa_tree_teardown_switches
-> dsa_switch_teardown
-> dsa_switch_teardown_tag_protocol
-> finally frees the tagger-owned storage
Fixes: 7f2973149c22 ("net: dsa: make tagging protocols connect to individual switches from a tree")
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Saeed Mahameed <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
x25_lapb_receive_frame() using skb_copy() to get a private copy of
skb, the new skb should be freed in the undersized/fragmented skb
error handling path. Otherwise there is a memory leak.
Fixes: cb101ed2c3c7 ("x25: Handle undersized/fragmented skbs")
Signed-off-by: Wei Yongjun <[email protected]>
Acked-by: Martin Schiller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
ag71xx_open()
If ag71xx_hw_enable() fails, call phylink_disconnect_phy() to clean up.
And if phylink_of_phy_connect() fails, nothing needs to be done.
Compile tested only.
Fixes: 892e09153fa3 ("net: ag71xx: port to phylink")
Signed-off-by: Liu Jian <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull netfx fixes from David Howells:
"Two fixes, affecting the functions that iterates over the pagecache
unmarking or unlocking pages after an op is complete:
- xas_for_each() loops must call xas_retry() first thing and
immediately do a "continue" in the case that the extracted value is
a special value that indicates that the walk raced with a
modification. Fix the unlock and unmark loops to do this.
- The maths in the unlock loop is dodgy as it could, theoretically,
at some point in the future end up with a starting file pointer
that is in the middle of a folio. This will cause a subtraction to
go negative - but the number is unsigned. Fix the maths to use
absolute file positions instead of relative page indices"
* tag 'netfs-fixes-20221115' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Fix dodgy maths
netfs: Fix missing xas_retry() calls in xarray iteration
|
|
Current dual mode adaptor ("DP++") detection code assumes that all
adaptors support i2c sub-addressing for read operations from the
DP-HDMI adaptor ID buffer. It has been observed that multiple
adaptors do not in fact support this, and always return data starting
at register 0. On affected adaptors, the code fails to read the proper
registers that would identify the device as a type 2 adaptor, and
handles those as type 1, limiting the TMDS clock to 165MHz, even if
the according register would announce a higher TMDS clock.
Fix this by always reading the ID buffer starting from offset 0, and
discarding any bytes before the actual offset of interest.
We tried finding authoritative documentation on whether or not this is
allowed behaviour, but since all the official VESA docs are paywalled,
the best we could come up with was the spec sheet for Texas Instruments'
SNx5DP149 chip family.[1] It explicitly mentions that sub-addressing is
supported for register writes, but *not* for reads (See NOTE in
section 8.5.3). Unless TI openly decided to violate the VESA spec, one
could take that as a hint that sub-addressing is in fact not mandated
by VESA.
The other two adaptors affected used the PS8409(A) and the LT8611,
according to the data returned from their ID buffers.
[1] https://www.ti.com/lit/ds/symlink/sn75dp149.pdf
Cc: [email protected]
Signed-off-by: Simon Rettberg <[email protected]>
Reviewed-by: Rafael Gieschke <[email protected]>
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/20221006113314.41101987@computer
Acked-by: Jani Nikula <[email protected]>
|
|
If the returning value of SMB2_close_init is an error-value,
exit the function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 352d96f3acc6 ("cifs: multichannel: move channel selection above transport layer")
Signed-off-by: Anastasia Belova <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
"Most patches randomly fix error paths or corner cases in fscache mode
reported recently. One fixes an invalid access relating to fragments
on crafted images.
Summary:
- Fix packed_inode invalid access when reading fragments on crafted
images
- Add a missing erofs_put_metabuf() in an error path in fscache mode
- Fix incorrect `count' for unmapped extents in fscache mode
- Fix use-after-free of fsid and domain_id string when remounting
- Fix missing xas_retry() in fscache mode"
* tag 'erofs-for-6.1-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix missing xas_retry() in fscache mode
erofs: fix use-after-free of fsid and domain_id string
erofs: get correct count for unmapped range in fscache mode
erofs: put metabuf in error path in fscache mode
erofs: fix general protection fault when reading fragment
|
|
The workaround designed for some specific ASICs is wrongly applied
to SMU13 ASICs. That leads to some runpm hang.
Signed-off-by: Evan Quan <[email protected]>
Reviewed-by: Hawking Zhang <[email protected]>
Reviewed-by: Feifei Xu <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
Enable SMU13.0.7 runpm support.
Signed-off-by: Evan Quan <[email protected]>
Reviewed-by: Hawking Zhang <[email protected]>
Reviewed-by: Feifei Xu <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected] # 6.0.x
|
|
Enable SMU13.0.0 runpm support.
Signed-off-by: Evan Quan <[email protected]>
Reviewed-by: Hawking Zhang <[email protected]>
Reviewed-by: Feifei Xu <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected] # 6.0.x
|