aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2021-12-16riscv: dts: sifive unmatched: Fix regulator for board rev3Vincent Pelletier1-60/+24
The existing values are rejected by the da9063 regulator driver, as they are unachievable with the declared chip setup (non-merged vcore and bmem are unable to provide the declared curent). Fix voltages to match rev3 schematics, which also matches their boot-up configuration within the chip's available precision. Declare bcore1/bcore2 and bmem/bio as merged. Set ldo09 and ldo10 as always-on as their consumers are not declared but exist. Drop ldo current limits as there is no current limit feature for these regulators in the DA9063. Fixes warnings like: DA9063_LDO3: Operation of current configuration missing Signed-off-by: Vincent Pelletier <[email protected]> Signed-off-by: Palmer Dabbelt <[email protected]>
2021-12-16riscv: dts: sifive unmatched: Expose the PMIC sub-functionsVincent Pelletier1-0/+12
These sub-functions are available in the chip revision on this board, so expose them. Signed-off-by: Vincent Pelletier <[email protected]> Signed-off-by: Palmer Dabbelt <[email protected]>
2021-12-16riscv: dts: sifive unmatched: Expose the board ID eepromVincent Pelletier1-0/+10
Mark it as read-only as it is factory-programmed with identifying information, and no executable nor configuration: - eth MAC address - board model (PCB version, BoM version) - board serial number Accidental modification would cause misidentification which could brick the board, so marking read-only seem like both a safe and non-constraining choice. Signed-off-by: Vincent Pelletier <[email protected]> Signed-off-by: Palmer Dabbelt <[email protected]>
2021-12-16riscv: dts: sifive unmatched: Name gpio linesVincent Pelletier1-0/+4
Follow the pin descriptions given in the version 3 of the board schematics. Signed-off-by: Vincent Pelletier <[email protected]> Signed-off-by: Palmer Dabbelt <[email protected]>
2021-12-17Merge tag 'amd-drm-fixes-5.16-2021-12-15' of ↵Dave Airlie15-16/+32
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes amd-drm-fixes-5.16-2021-12-15: amdgpu: - Fix RLC register offset - GMC fix - Properly cache SMU FW version on Yellow Carp - Fix missing callback on DCN3.1 - Reset DMCUB before HW init - Fix for GMC powergating on PCO - Fix a possible memory leak in GPU metrics table handling on RN Signed-off-by: Dave Airlie <[email protected]> From: Alex Deucher <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2021-12-17Merge tag 'drm-misc-fixes-2021-12-16-1' of ↵Dave Airlie3-3/+12
ssh://git.freedesktop.org/git/drm/drm-misc into drm-fixes One null pointer dereference fix for ast, a pixel clock unit fix for simpledrm and a user-space regression revert for fb-helper Signed-off-by: Dave Airlie <[email protected]> From: Maxime Ripard <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/20211216082603.pm6yzlckmxvwnqyv@houat
2021-12-16scsi: lpfc: Terminate string in lpfc_debugfs_nvmeio_trc_write()Dan Carpenter1-2/+2
The "mybuf" string comes from the user, so we need to ensure that it is NUL terminated. Link: https://lore.kernel.org/r/20211214070527.GA27934@kili Fixes: bd2cdd5e400f ("scsi: lpfc: NVME Initiator: Add debugfs support") Reviewed-by: James Smart <[email protected]> Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2021-12-17crypto: qat - do not handle PFVF sources for qat_4xxxGiovanni Cabiddu1-0/+7
The QAT driver does not have support for PFVF interrupts for GEN4 devices, therefore report the vf2pf sources as 0. This prevents a NULL pointer dereference in the function adf_msix_isr_ae() if the device triggers a spurious interrupt. Fixes: 993161d36ab5 ("crypto: qat - fix handling of VF to PF interrupts") Reported-by: Adam Guerin <[email protected]> Signed-off-by: Giovanni Cabiddu <[email protected]> Signed-off-by: Herbert Xu <[email protected]>
2021-12-17libata: if T_LENGTH is zero, dma direction should be DMA_NONEGeorge Kennedy1-2/+13
Avoid data corruption by rejecting pass-through commands where T_LENGTH is zero (No data is transferred) and the dma direction is not DMA_NONE. Cc: <[email protected]> Reported-by: syzkaller<[email protected]> Signed-off-by: George Kennedy<[email protected]> Signed-off-by: Damien Le Moal <[email protected]>
2021-12-16Merge tag 'audit-pr-20211216' of ↵Linus Torvalds1-11/+10
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit Pull audit fix from Paul Moore: "A single patch to fix a problem where the audit queue could grow unbounded when the audit daemon is forcibly stopped" * tag 'audit-pr-20211216' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit: audit: improve robustness of the audit queue handling
2021-12-16Merge tag 'net-5.16-rc6' of ↵Linus Torvalds81-198/+881
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Networking fixes, including fixes from mac80211, wifi, bpf. Relatively large batches of fixes from BPF and the WiFi stack, calm in general networking. Current release - regressions: - dpaa2-eth: fix buffer overrun when reporting ethtool statistics Current release - new code bugs: - bpf: fix incorrect state pruning for <8B spill/fill - iavf: - add missing unlocks in iavf_watchdog_task() - do not override the adapter state in the watchdog task (again) - mlxsw: spectrum_router: consolidate MAC profiles when possible Previous releases - regressions: - mac80211 fixes: - rate control, avoid driver crash for retransmitted frames - regression in SSN handling of addba tx - a memory leak where sta_info is not freed - marking TX-during-stop for TX in in_reconfig, prevent stall - cfg80211: acquire wiphy mutex on regulatory work - wifi drivers: fix build regressions and LED config dependency - virtio_net: fix rx_drops stat for small pkts - dsa: mv88e6xxx: unforce speed & duplex in mac_link_down() Previous releases - always broken: - bpf fixes: - kernel address leakage in atomic fetch - kernel address leakage in atomic cmpxchg's r0 aux reg - signed bounds propagation after mov32 - extable fixup offset - extable address check - mac80211: - fix the size used for building probe request - send ADDBA requests using the tid/queue of the aggregation session - agg-tx: don't schedule_and_wake_txq() under sta->lock, avoid deadlocks - validate extended element ID is present - mptcp: - never allow the PM to close a listener subflow (null-defer) - clear 'kern' flag from fallback sockets, prevent crash - fix deadlock in __mptcp_push_pending() - inet_diag: fix kernel-infoleak for UDP sockets - xsk: do not sleep in poll() when need_wakeup set - smc: avoid very long waits in smc_release() - sch_ets: don't remove idle classes from the round-robin list - netdevsim: - zero-initialize memory for bpf map's value, prevent info leak - don't let user space overwrite read only (max) ethtool parms - ixgbe: set X550 MDIO speed before talking to PHY - stmmac: - fix null-deref in flower deletion w/ VLAN prio Rx steering - dwmac-rk: fix oob read in rk_gmac_setup - ice: time stamping fixes - systemport: add global locking for descriptor life cycle" * tag 'net-5.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (89 commits) bpf, selftests: Fix racing issue in btf_skc_cls_ingress test selftest/bpf: Add a test that reads various addresses. bpf: Fix extable address check. bpf: Fix extable fixup offset. bpf, selftests: Add test case trying to taint map value pointer bpf: Make 32->64 bounds propagation slightly more robust bpf: Fix signed bounds propagation after mov32 sit: do not call ipip6_dev_free() from sit_init_net() net: systemport: Add global locking for descriptor lifecycle net/smc: Prevent smc_release() from long blocking net: Fix double 0x prefix print in SKB dump virtio_net: fix rx_drops stat for small pkts dsa: mv88e6xxx: fix debug print for SPEED_UNFORCED sfc_ef100: potential dereference of null pointer net: stmmac: dwmac-rk: fix oob read in rk_gmac_setup net: usb: lan78xx: add Allied Telesis AT29M2-AF net/packet: rx_owner_map depends on pg_vec netdevsim: Zero-initialize memory for new map's value in function nsim_bpf_map_alloc dpaa2-eth: fix ethtool statistics ixgbe: set X550 MDIO speed before talking to PHY ...
2021-12-16Merge tag 'soc-fixes-5.16-3' of ↵Linus Torvalds32-57/+84
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "There are a number of DT fixes, mostly for mistakes found through static checking of the dts files again, as well as a couple of minor changes to address incorrect DT settings. For i.MX, there is yet another series of devitree changes to update RGMII delay settings for ethernet, which is an ongoing problem after some driver changes. For SoC specific device drivers, a number of smaller fixes came up: - i.MX SoC identification was incorrectly registered non-i.MX machines when the driver is built-in - One fix on imx8m-blk-ctrl driver to get i.MX8MM MIPI reset work properly - a few compile fixes for warnings that get in the way of -Werror - a string overflow in the scpi firmware driver - a boot failure with FORTIFY_SOURCE on Rockchips machines - broken error handling in the AMD TEE driver - a revert for a tegra reset driver commit that broke HDA" * tag 'soc-fixes-5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits) soc/tegra: fuse: Fix bitwise vs. logical OR warning firmware: arm_scpi: Fix string overflow in SCPI genpd driver soc: imx: Register SoC device only on i.MX boards soc: imx: imx8m-blk-ctrl: Fix imx8mm mipi reset ARM: dts: imx6ull-pinfunc: Fix CSI_DATA07__ESAI_TX0 pad name arm64: dts: imx8mq: remove interconnect property from lcdif ARM: socfpga: dts: fix qspi node compatible arm64: dts: apple: add #interrupt-cells property to pinctrl nodes dt-bindings: i2c: apple,i2c: allow multiple compatibles arm64: meson: remove COMMON_CLK arm64: meson: fix dts for JetHub D1 tee: amdtee: fix an IS_ERR() vs NULL bug arm64: dts: apple: change ethernet0 device type to ethernet arm64: dts: ten64: remove redundant interrupt declaration for gpio-keys arm64: dts: rockchip: fix poweroff on helios64 arm64: dts: rockchip: fix audio-supply for Rock Pi 4 arm64: dts: rockchip: fix rk3399-leez-p710 vcc3v3-lan supply arm64: dts: rockchip: fix rk3308-roc-cc vcc-sd supply arm64: dts: rockchip: remove mmc-hs400-enhanced-strobe from rk3399-khadas-edge ARM: rockchip: Use memcpy_toio instead of memcpy on smp bring-up ...
2021-12-16selinux: fix sleeping function called from invalid contextScott Mayhew1-14/+19
selinux_sb_mnt_opts_compat() is called via sget_fc() under the sb_lock spinlock, so it can't use GFP_KERNEL allocations: [ 868.565200] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:230 [ 868.568246] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 4914, name: mount.nfs [ 868.569626] preempt_count: 1, expected: 0 [ 868.570215] RCU nest depth: 0, expected: 0 [ 868.570809] Preemption disabled at: [ 868.570810] [<0000000000000000>] 0x0 [ 868.571848] CPU: 1 PID: 4914 Comm: mount.nfs Kdump: loaded Tainted: G W 5.16.0-rc5.2585cf9dfa #1 [ 868.573273] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-4.fc34 04/01/2014 [ 868.574478] Call Trace: [ 868.574844] <TASK> [ 868.575156] dump_stack_lvl+0x34/0x44 [ 868.575692] __might_resched.cold+0xd6/0x10f [ 868.576308] slab_pre_alloc_hook.constprop.0+0x89/0xf0 [ 868.577046] __kmalloc_track_caller+0x72/0x420 [ 868.577684] ? security_context_to_sid_core+0x48/0x2b0 [ 868.578569] kmemdup_nul+0x22/0x50 [ 868.579108] security_context_to_sid_core+0x48/0x2b0 [ 868.579854] ? _nfs4_proc_pathconf+0xff/0x110 [nfsv4] [ 868.580742] ? nfs_reconfigure+0x80/0x80 [nfs] [ 868.581355] security_context_str_to_sid+0x36/0x40 [ 868.581960] selinux_sb_mnt_opts_compat+0xb5/0x1e0 [ 868.582550] ? nfs_reconfigure+0x80/0x80 [nfs] [ 868.583098] security_sb_mnt_opts_compat+0x2a/0x40 [ 868.583676] nfs_compare_super+0x113/0x220 [nfs] [ 868.584249] ? nfs_try_mount_request+0x210/0x210 [nfs] [ 868.584879] sget_fc+0xb5/0x2f0 [ 868.585267] nfs_get_tree_common+0x91/0x4a0 [nfs] [ 868.585834] vfs_get_tree+0x25/0xb0 [ 868.586241] fc_mount+0xe/0x30 [ 868.586605] do_nfs4_mount+0x130/0x380 [nfsv4] [ 868.587160] nfs4_try_get_tree+0x47/0xb0 [nfsv4] [ 868.587724] vfs_get_tree+0x25/0xb0 [ 868.588193] do_new_mount+0x176/0x310 [ 868.588782] __x64_sys_mount+0x103/0x140 [ 868.589388] do_syscall_64+0x3b/0x90 [ 868.589935] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 868.590699] RIP: 0033:0x7f2b371c6c4e [ 868.591239] Code: 48 8b 0d dd 71 0e 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 49 89 ca b8 a5 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d aa 71 0e 00 f7 d8 64 89 01 48 [ 868.593810] RSP: 002b:00007ffc83775d88 EFLAGS: 00000246 ORIG_RAX: 00000000000000a5 [ 868.594691] RAX: ffffffffffffffda RBX: 00007ffc83775f10 RCX: 00007f2b371c6c4e [ 868.595504] RDX: 0000555d517247a0 RSI: 0000555d51724700 RDI: 0000555d51724540 [ 868.596317] RBP: 00007ffc83775f10 R08: 0000555d51726890 R09: 0000555d51726890 [ 868.597162] R10: 0000000000000000 R11: 0000000000000246 R12: 0000555d51726890 [ 868.598005] R13: 0000000000000003 R14: 0000555d517246e0 R15: 0000555d511ac925 [ 868.598826] </TASK> Cc: [email protected] Fixes: 69c4a42d72eb ("lsm,selinux: add new hook to compare new mount to an existing mount") Signed-off-by: Scott Mayhew <[email protected]> [PM: cleanup/line-wrap the backtrace] Signed-off-by: Paul Moore <[email protected]>
2021-12-16Merge https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfJakub Kicinski12-30/+434
Daniel Borkmann says: ==================== pull-request: bpf 2021-12-16 We've added 15 non-merge commits during the last 7 day(s) which contain a total of 12 files changed, 434 insertions(+), 30 deletions(-). The main changes are: 1) Fix incorrect verifier state pruning behavior for <8B register spill/fill, from Paul Chaignon. 2) Fix x86-64 JIT's extable handling for fentry/fexit when return pointer is an ERR_PTR(), from Alexei Starovoitov. 3) Fix 3 different possibilities that BPF verifier missed where unprivileged could leak kernel addresses, from Daniel Borkmann. 4) Fix xsk's poll behavior under need_wakeup flag, from Magnus Karlsson. 5) Fix an oob-write in test_verifier due to a missed MAX_NR_MAPS bump, from Kumar Kartikeya Dwivedi. 6) Fix a race in test_btf_skc_cls_ingress selftest, from Martin KaFai Lau. * https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf: bpf, selftests: Fix racing issue in btf_skc_cls_ingress test selftest/bpf: Add a test that reads various addresses. bpf: Fix extable address check. bpf: Fix extable fixup offset. bpf, selftests: Add test case trying to taint map value pointer bpf: Make 32->64 bounds propagation slightly more robust bpf: Fix signed bounds propagation after mov32 bpf, selftests: Update test case for atomic cmpxchg on r0 with pointer bpf: Fix kernel address leakage in atomic cmpxchg's r0 aux reg bpf, selftests: Add test case for atomic fetch on spilled pointer bpf: Fix kernel address leakage in atomic fetch selftests/bpf: Fix OOB write in test_verifier xsk: Do not sleep in poll() when need_wakeup set selftests/bpf: Tests for state pruning with u32 spill/fill bpf: Fix incorrect state pruning for <8B spill/fill ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-12-16bpf, selftests: Fix racing issue in btf_skc_cls_ingress testMartin KaFai Lau1-2/+14
The libbpf CI reported occasional failure in btf_skc_cls_ingress: test_syncookie:FAIL:Unexpected syncookie states gen_cookie:80326634 recv_cookie:0 bpf prog error at line 97 "error at line 97" means the bpf prog cannot find the listening socket when the final ack is received. It then skipped processing the syncookie in the final ack which then led to "recv_cookie:0". The problem is the userspace program did not do accept() and went ahead to close(listen_fd) before the kernel (and the bpf prog) had a chance to process the final ack. The fix is to add accept() call so that the userspace will wait for the kernel to finish processing the final ack first before close()-ing everything. Fixes: 9a856cae2217 ("bpf: selftest: Add test_btf_skc_cls_ingress") Reported-by: Andrii Nakryiko <[email protected]> Signed-off-by: Martin KaFai Lau <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2021-12-16selftest/bpf: Add a test that reads various addresses.Alexei Starovoitov2-0/+32
Add a function to bpf_testmod that returns invalid kernel and user addresses. Then attach an fexit program to that function that tries to read memory through these addresses. This logic checks that bpf_probe_read_kernel and BPF_PROBE_MEM logic is sane. Signed-off-by: Alexei Starovoitov <[email protected]> Acked-by: Daniel Borkmann <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]>
2021-12-16bpf: Fix extable address check.Alexei Starovoitov1-7/+42
The verifier checks that PTR_TO_BTF_ID pointer is either valid or NULL, but it cannot distinguish IS_ERR pointer from valid one. When offset is added to IS_ERR pointer it may become small positive value which is a user address that is not handled by extable logic and has to be checked for at the runtime. Tighten BPF_PROBE_MEM pointer check code to prevent this case. Fixes: 4c5de127598e ("bpf: Emit explicit NULL pointer checks for PROBE_LDX instructions.") Reported-by: Lorenzo Fontana <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]> Acked-by: Daniel Borkmann <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]>
2021-12-16bpf: Fix extable fixup offset.Alexei Starovoitov1-1/+1
The prog - start_of_ldx is the offset before the faulting ldx to the location after it, so this will be used to adjust pt_regs->ip for jumping over it and continuing, and with old temp it would have been fixed up to the wrong offset, causing crash. Fixes: 4c5de127598e ("bpf: Emit explicit NULL pointer checks for PROBE_LDX instructions.") Signed-off-by: Alexei Starovoitov <[email protected]> Reviewed-by: Daniel Borkmann <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]>
2021-12-16Merge tag 'clk-fixes-for-linus' of ↵Linus Torvalds1-3/+12
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux Pull clk fix from Stephen Boyd: "A single fix for the clk framework that needed some more bake time in linux-next. The problem is that two clks being registered at the same time can lead to a busted clk tree if the parent isn't fully registered by the time the child finds the parent. We rejigger the place where we mark the parent as fully registered so that the child can't find the parent until things are proper" * tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: clk: Don't parent clks until the parent is fully registered
2021-12-16bpf, selftests: Add test case trying to taint map value pointerDaniel Borkmann1-0/+23
Add a test case which tries to taint map value pointer arithmetic into a unknown scalar with subsequent export through the map. Before fix: # ./test_verifier 1186 #1186/u map access: trying to leak tained dst reg FAIL Unexpected success to load! verification time 24 usec stack depth 8 processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 1 #1186/p map access: trying to leak tained dst reg FAIL Unexpected success to load! verification time 8 usec stack depth 8 processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 1 Summary: 0 PASSED, 0 SKIPPED, 2 FAILED After fix: # ./test_verifier 1186 #1186/u map access: trying to leak tained dst reg OK #1186/p map access: trying to leak tained dst reg OK Summary: 2 PASSED, 0 SKIPPED, 0 FAILED Signed-off-by: Daniel Borkmann <[email protected]> Reviewed-by: John Fastabend <[email protected]> Acked-by: Alexei Starovoitov <[email protected]>
2021-12-16bpf: Make 32->64 bounds propagation slightly more robustDaniel Borkmann1-9/+15
Make the bounds propagation in __reg_assign_32_into_64() slightly more robust and readable by aligning it similarly as we did back in the __reg_combine_64_into_32() counterpart. Meaning, only propagate or pessimize them as a smin/smax pair. Signed-off-by: Daniel Borkmann <[email protected]> Reviewed-by: John Fastabend <[email protected]> Acked-by: Alexei Starovoitov <[email protected]>
2021-12-16bpf: Fix signed bounds propagation after mov32Daniel Borkmann1-0/+4
For the case where both s32_{min,max}_value bounds are positive, the __reg_assign_32_into_64() directly propagates them to their 64 bit counterparts, otherwise it pessimises them into [0,u32_max] universe and tries to refine them later on by learning through the tnum as per comment in mentioned function. However, that does not always happen, for example, in mov32 operation we call zext_32_to_64(dst_reg) which invokes the __reg_assign_32_into_64() as is without subsequent bounds update as elsewhere thus no refinement based on tnum takes place. Thus, not calling into the __update_reg_bounds() / __reg_deduce_bounds() / __reg_bound_offset() triplet as we do, for example, in case of ALU ops via adjust_scalar_min_max_vals(), will lead to more pessimistic bounds when dumping the full register state: Before fix: 0: (b4) w0 = -1 1: R0_w=invP4294967295 (id=0,imm=ffffffff, smin_value=4294967295,smax_value=4294967295, umin_value=4294967295,umax_value=4294967295, var_off=(0xffffffff; 0x0), s32_min_value=-1,s32_max_value=-1, u32_min_value=-1,u32_max_value=-1) 1: (bc) w0 = w0 2: R0_w=invP4294967295 (id=0,imm=ffffffff, smin_value=0,smax_value=4294967295, umin_value=4294967295,umax_value=4294967295, var_off=(0xffffffff; 0x0), s32_min_value=-1,s32_max_value=-1, u32_min_value=-1,u32_max_value=-1) Technically, the smin_value=0 and smax_value=4294967295 bounds are not incorrect, but given the register is still a constant, they break assumptions about const scalars that smin_value == smax_value and umin_value == umax_value. After fix: 0: (b4) w0 = -1 1: R0_w=invP4294967295 (id=0,imm=ffffffff, smin_value=4294967295,smax_value=4294967295, umin_value=4294967295,umax_value=4294967295, var_off=(0xffffffff; 0x0), s32_min_value=-1,s32_max_value=-1, u32_min_value=-1,u32_max_value=-1) 1: (bc) w0 = w0 2: R0_w=invP4294967295 (id=0,imm=ffffffff, smin_value=4294967295,smax_value=4294967295, umin_value=4294967295,umax_value=4294967295, var_off=(0xffffffff; 0x0), s32_min_value=-1,s32_max_value=-1, u32_min_value=-1,u32_max_value=-1) Without the smin_value == smax_value and umin_value == umax_value invariant being intact for const scalars, it is possible to leak out kernel pointers from unprivileged user space if the latter is enabled. For example, when such registers are involved in pointer arithmtics, then adjust_ptr_min_max_vals() will taint the destination register into an unknown scalar, and the latter can be exported and stored e.g. into a BPF map value. Fixes: 3f50f132d840 ("bpf: Verifier, do explicit ALU32 bounds tracking") Reported-by: Kuee K1r0a <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Reviewed-by: John Fastabend <[email protected]> Acked-by: Alexei Starovoitov <[email protected]>
2021-12-16Merge tag 'arm64-fixes' of ↵Linus Torvalds1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fix from Catalin Marinas: "Fix missing error code on kexec failure path" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: kexec: Fix missing error code 'ret' warning in load_other_segments()
2021-12-16ksmbd: fix uninitialized symbol 'pntsd_size'Namjae Jeon1-0/+4
No check for if "rc" is an error code for build_sec_desc(). This can cause problems with using uninitialized pntsd_size. Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3") Cc: [email protected] # v5.15 Reported-by: Dan Carpenter <[email protected]> Signed-off-by: Namjae Jeon <[email protected]> Signed-off-by: Steve French <[email protected]>
2021-12-16ksmbd: fix error code in ndr_read_int32()Dan Carpenter1-1/+1
This is a failure path and it should return -EINVAL instead of success. Otherwise it could result in the caller using uninitialized memory. Fixes: 303fff2b8c77 ("ksmbd: add validation for ndr read/write functions") Cc: [email protected] # v5.15 Acked-by: Namjae Jeon <[email protected]> Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Steve French <[email protected]>
2021-12-16Merge tag 'for-5.16/dm-fixes' of ↵Linus Torvalds2-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm Pull device mapper fixes from Mike Snitzer: - Fix use after free in DM btree remove's rebalance_children() - Fix DM integrity data corruption, introduced during 5.16 merge, due to improper use of bvec_kmap_local() * tag 'for-5.16/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: dm integrity: fix data corruption due to improper use of bvec_kmap_local dm btree remove: fix use after free in rebalance_children()
2021-12-16arm64: kexec: Fix missing error code 'ret' warning in load_other_segments()Lakshmi Ramasubramanian1-0/+1
Since commit ac10be5cdbfa ("arm64: Use common of_kexec_alloc_and_setup_fdt()"), smatch reports the following warning: arch/arm64/kernel/machine_kexec_file.c:152 load_other_segments() warn: missing error code 'ret' Return code is not set to an error code in load_other_segments() when of_kexec_alloc_and_setup_fdt() call returns a NULL dtb. This results in status success (return code set to 0) being returned from load_other_segments(). Set return code to -EINVAL if of_kexec_alloc_and_setup_fdt() returns NULL dtb. Signed-off-by: Lakshmi Ramasubramanian <[email protected]> Reported-by: kernel test robot <[email protected]> Reported-by: Dan Carpenter <[email protected]> Fixes: ac10be5cdbfa ("arm64: Use common of_kexec_alloc_and_setup_fdt()") Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Will Deacon <[email protected]> Signed-off-by: Catalin Marinas <[email protected]>
2021-12-16afs: Fix mmapDavid Howells2-2/+4
Fix afs_add_open_map() to check that the vnode isn't already on the list when it adds it. It's possible that afs_drop_open_mmap() decremented the cb_nr_mmap counter, but hadn't yet got into the locked section to remove it. Also vnode->cb_mmap_link should be initialised, so fix that too. Fixes: 6e0e99d58a65 ("afs: Fix mmap coherency vs 3rd-party changes") Reported-by: [email protected] Suggested-by: Marc Dionne <[email protected]> Signed-off-by: David Howells <[email protected]> Tested-by: [email protected] cc: [email protected] Link: https://lore.kernel.org/r/[email protected]/ # v1 Signed-off-by: Linus Torvalds <[email protected]>
2021-12-16sit: do not call ipip6_dev_free() from sit_init_net()Eric Dumazet1-1/+0
ipip6_dev_free is sit dev->priv_destructor, already called by register_netdevice() if something goes wrong. Alternative would be to make ipip6_dev_free() robust against multiple invocations, but other drivers do not implement this strategy. syzbot reported: dst_release underflow WARNING: CPU: 0 PID: 5059 at net/core/dst.c:173 dst_release+0xd8/0xe0 net/core/dst.c:173 Modules linked in: CPU: 1 PID: 5059 Comm: syz-executor.4 Not tainted 5.16.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:dst_release+0xd8/0xe0 net/core/dst.c:173 Code: 4c 89 f2 89 d9 31 c0 5b 41 5e 5d e9 da d5 44 f9 e8 1d 90 5f f9 c6 05 87 48 c6 05 01 48 c7 c7 80 44 99 8b 31 c0 e8 e8 67 29 f9 <0f> 0b eb 85 0f 1f 40 00 53 48 89 fb e8 f7 8f 5f f9 48 83 c3 a8 48 RSP: 0018:ffffc9000aa5faa0 EFLAGS: 00010246 RAX: d6894a925dd15a00 RBX: 00000000ffffffff RCX: 0000000000040000 RDX: ffffc90005e19000 RSI: 000000000003ffff RDI: 0000000000040000 RBP: 0000000000000000 R08: ffffffff816a1f42 R09: ffffed1017344f2c R10: ffffed1017344f2c R11: 0000000000000000 R12: 0000607f462b1358 R13: 1ffffffff1bfd305 R14: ffffe8ffffcb1358 R15: dffffc0000000000 FS: 00007f66c71a2700(0000) GS:ffff8880b9a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f88aaed5058 CR3: 0000000023e0f000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> dst_cache_destroy+0x107/0x1e0 net/core/dst_cache.c:160 ipip6_dev_free net/ipv6/sit.c:1414 [inline] sit_init_net+0x229/0x550 net/ipv6/sit.c:1936 ops_init+0x313/0x430 net/core/net_namespace.c:140 setup_net+0x35b/0x9d0 net/core/net_namespace.c:326 copy_net_ns+0x359/0x5c0 net/core/net_namespace.c:470 create_new_namespaces+0x4ce/0xa00 kernel/nsproxy.c:110 unshare_nsproxy_namespaces+0x11e/0x180 kernel/nsproxy.c:226 ksys_unshare+0x57d/0xb50 kernel/fork.c:3075 __do_sys_unshare kernel/fork.c:3146 [inline] __se_sys_unshare kernel/fork.c:3144 [inline] __x64_sys_unshare+0x34/0x40 kernel/fork.c:3144 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f66c882ce99 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f66c71a2168 EFLAGS: 00000246 ORIG_RAX: 0000000000000110 RAX: ffffffffffffffda RBX: 00007f66c893ff60 RCX: 00007f66c882ce99 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000048040200 RBP: 00007f66c8886ff1 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007fff6634832f R14: 00007f66c71a2300 R15: 0000000000022000 </TASK> Fixes: cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.") Signed-off-by: Eric Dumazet <[email protected]> Reported-by: syzbot <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-12-16net: systemport: Add global locking for descriptor lifecycleFlorian Fainelli2-1/+5
The descriptor list is a shared resource across all of the transmit queues, and the locking mechanism used today only protects concurrency across a given transmit queue between the transmit and reclaiming. This creates an opportunity for the SYSTEMPORT hardware to work on corrupted descriptors if we have multiple producers at once which is the case when using multiple transmit queues. This was particularly noticeable when using multiple flows/transmit queues and it showed up in interesting ways in that UDP packets would get a correct UDP header checksum being calculated over an incorrect packet length. Similarly TCP packets would get an equally correct checksum computed by the hardware over an incorrect packet length. The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges when the driver produces a new descriptor anytime it writes to the WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to re-organize its descriptors and it is possible that concurrent TX queues eventually break this internal allocation scheme to the point where the length/status part of the descriptor gets used for an incorrect data buffer. The fix is to impose a global serialization for all TX queues in the short section where we are writing to the WRITE_PORT_{HI,LO} registers which solves the corruption even with multiple concurrent TX queues being used. Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Florian Fainelli <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-12-16net/smc: Prevent smc_release() from long blockingD. Wythe1-1/+3
In nginx/wrk benchmark, there's a hung problem with high probability on case likes that: (client will last several minutes to exit) server: smc_run nginx client: smc_run wrk -c 10000 -t 1 http://server Client hangs with the following backtrace: 0 [ffffa7ce8Of3bbf8] __schedule at ffffffff9f9eOd5f 1 [ffffa7ce8Of3bc88] schedule at ffffffff9f9eløe6 2 [ffffa7ce8Of3bcaO] schedule_timeout at ffffffff9f9e3f3c 3 [ffffa7ce8Of3bd2O] wait_for_common at ffffffff9f9el9de 4 [ffffa7ce8Of3bd8O] __flush_work at ffffffff9fOfeOl3 5 [ffffa7ce8øf3bdfO] smc_release at ffffffffcO697d24 [smc] 6 [ffffa7ce8Of3be2O] __sock_release at ffffffff9f8O2e2d 7 [ffffa7ce8Of3be4ø] sock_close at ffffffff9f8ø2ebl 8 [ffffa7ce8øf3be48] __fput at ffffffff9f334f93 9 [ffffa7ce8Of3be78] task_work_run at ffffffff9flOlff5 10 [ffffa7ce8Of3beaO] do_exit at ffffffff9fOe5Ol2 11 [ffffa7ce8Of3bflO] do_group_exit at ffffffff9fOe592a 12 [ffffa7ce8Of3bf38] __x64_sys_exit_group at ffffffff9fOe5994 13 [ffffa7ce8Of3bf4O] do_syscall_64 at ffffffff9f9d4373 14 [ffffa7ce8Of3bfsO] entry_SYSCALL_64_after_hwframe at ffffffff9fa0007c This issue dues to flush_work(), which is used to wait for smc_connect_work() to finish in smc_release(). Once lots of smc_connect_work() was pending or all executing work dangling, smc_release() has to block until one worker comes to free, which is equivalent to wait another smc_connnect_work() to finish. In order to fix this, There are two changes: 1. For those idle smc_connect_work(), cancel it from the workqueue; for executing smc_connect_work(), waiting for it to finish. For that purpose, replace flush_work() with cancel_work_sync(). 2. Since smc_connect() hold a reference for passive closing, if smc_connect_work() has been cancelled, release the reference. Fixes: 24ac3a08e658 ("net/smc: rebuild nonblocking connect") Reported-by: Tony Lu <[email protected]> Tested-by: Dust Li <[email protected]> Reviewed-by: Dust Li <[email protected]> Reviewed-by: Tony Lu <[email protected]> Signed-off-by: D. Wythe <[email protected]> Acked-by: Karsten Graul <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-12-16optee: Suppress false positive kmemleak report in optee_handle_rpc()Xiaolei Wang1-0/+2
We observed the following kmemleak report: unreferenced object 0xffff000007904500 (size 128): comm "swapper/0", pid 1, jiffies 4294892671 (age 44.036s) hex dump (first 32 bytes): 00 47 90 07 00 00 ff ff 60 00 c0 ff 00 00 00 00 .G......`....... 60 00 80 13 00 80 ff ff a0 00 00 00 00 00 00 00 `............... backtrace: [<000000004c12b1c7>] kmem_cache_alloc+0x1ac/0x2f4 [<000000005d23eb4f>] tee_shm_alloc+0x78/0x230 [<00000000794dd22c>] optee_handle_rpc+0x60/0x6f0 [<00000000d9f7c52d>] optee_do_call_with_arg+0x17c/0x1dc [<00000000c35884da>] optee_open_session+0x128/0x1ec [<000000001748f2ff>] tee_client_open_session+0x28/0x40 [<00000000aecb5389>] optee_enumerate_devices+0x84/0x2a0 [<000000003df18bf1>] optee_probe+0x674/0x6cc [<000000003a4a534a>] platform_drv_probe+0x54/0xb0 [<000000000c51ce7d>] really_probe+0xe4/0x4d0 [<000000002f04c865>] driver_probe_device+0x58/0xc0 [<00000000b485397d>] device_driver_attach+0xc0/0xd0 [<00000000c835f0df>] __driver_attach+0x84/0x124 [<000000008e5a429c>] bus_for_each_dev+0x70/0xc0 [<000000001735e8a8>] driver_attach+0x24/0x30 [<000000006d94b04f>] bus_add_driver+0x104/0x1ec This is not a memory leak because we pass the share memory pointer to secure world and would get it from secure world before releasing it. Signed-off-by: Xiaolei Wang <[email protected]> Signed-off-by: Jens Wiklander <[email protected]>
2021-12-16tee: optee: Fix incorrect page free bugSumit Garg1-4/+2
Pointer to the allocated pages (struct page *page) has already progressed towards the end of allocation. It is incorrect to perform __free_pages(page, order) using this pointer as we would free any arbitrary pages. Fix this by stop modifying the page pointer. Fixes: ec185dd3ab25 ("optee: Fix memory leak when failing to register shm pages") Cc: [email protected] Reported-by: Patrik Lantz <[email protected]> Signed-off-by: Sumit Garg <[email protected]> Reviewed-by: Tyler Hicks <[email protected]> Signed-off-by: Jens Wiklander <[email protected]>
2021-12-16Merge tag 'tegra-for-5.16-soc-fixes' of ↵Arnd Bergmann2-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes soc/tegra: Fixes for v5.16-rc6 This contains a single build fix without which ARM allmodconfig builds are broken if -Werror is enabled. * tag 'tegra-for-5.16-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: soc/tegra: fuse: Fix bitwise vs. logical OR warning Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnd Bergmann <[email protected]>
2021-12-16netfilter: ctnetlink: remove expired entries firstFlorian Westphal1-2/+3
When dumping conntrack table to userspace via ctnetlink, check if the ct has already expired before doing any of the 'skip' checks. This expires dead entries faster. /proc handler also removes outdated entries first. Reported-by: Vitaly Zuevsky <[email protected]> Signed-off-by: Florian Westphal <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
2021-12-16net: Fix double 0x prefix print in SKB dumpGal Pressman1-1/+1
When printing netdev features %pNF already takes care of the 0x prefix, remove the explicit one. Fixes: 6413139dfc64 ("skbuff: increase verbosity when dumping skb data") Signed-off-by: Gal Pressman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-12-16virtio_net: fix rx_drops stat for small pktsWenliang Wang1-6/+3
We found the stat of rx drops for small pkts does not increment when build_skb fail, it's not coherent with other mode's rx drops stat. Signed-off-by: Wenliang Wang <[email protected]> Acked-by: Jason Wang <[email protected]> Acked-by: Michael S. Tsirkin <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-12-16dsa: mv88e6xxx: fix debug print for SPEED_UNFORCEDAndrey Eremeev1-2/+2
Debug print uses invalid check to detect if speed is unforced: (speed != SPEED_UNFORCED) should be used instead of (!speed). Found by Linux Verification Center (linuxtesting.org) with SVACE. Signed-off-by: Andrey Eremeev <[email protected]> Fixes: 96a2b40c7bd3 ("net: dsa: mv88e6xxx: add port's MAC speed setter") Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-12-16sfc_ef100: potential dereference of null pointerJiasheng Jiang1-0/+3
The return value of kmalloc() needs to be checked. To avoid use in efx_nic_update_stats() in case of the failure of alloc. Fixes: b593b6f1b492 ("sfc_ef100: statistics gathering") Signed-off-by: Jiasheng Jiang <[email protected]> Reported-by: kernel test robot <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-12-16net: stmmac: dwmac-rk: fix oob read in rk_gmac_setupJohn Keeping1-1/+3
KASAN reports an out-of-bounds read in rk_gmac_setup on the line: while (ops->regs[i]) { This happens for most platforms since the regs flexible array member is empty, so the memory after the ops structure is being read here. It seems that mostly this happens to contain zero anyway, so we get lucky and everything still works. To avoid adding redundant data to nearly all the ops structures, add a new flag to indicate whether the regs field is valid and avoid this loop when it is not. Fixes: 3bb3d6b1c195 ("net: stmmac: Add RK3566/RK3568 SoC support") Signed-off-by: John Keeping <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-12-16Merge branch '1GbE' of ↵David S. Miller6-15/+39
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-12-15 This series contains updates to igb, igbvf, igc and ixgbe drivers. Karen moves checks for invalid VF MAC filters to occur earlier for igb. Letu Ren fixes a double free issue in igbvf probe. Sasha fixes incorrect min value being used when calculating for max for igc. Robert Schlabbach adds documentation on enabling NBASE-T support for ixgbe. Cyril Novikov adds missing initialization of MDIO bus speed for ixgbe. ==================== Signed-off-by: David S. Miller <[email protected]>
2021-12-16arm64: dts: lx2160a: fix scl-gpios property nameZhang Ying-224551-2/+2
Fix the typo in the property name. Fixes: d548c217c6a3c ("arm64: dts: add QorIQ LX2160A SoC support") Signed-off-by: Zhang Ying <[email protected]> Signed-off-by: Li Yang <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2021-12-16tee: handle lookup of shm with reference count 0Jens Wiklander2-110/+68
Since the tee subsystem does not keep a strong reference to its idle shared memory buffers, it races with other threads that try to destroy a shared memory through a close of its dma-buf fd or by unmapping the memory. In tee_shm_get_from_id() when a lookup in teedev->idr has been successful, it is possible that the tee_shm is in the dma-buf teardown path, but that path is blocked by the teedev mutex. Since we don't have an API to tell if the tee_shm is in the dma-buf teardown path or not we must find another way of detecting this condition. Fix this by doing the reference counting directly on the tee_shm using a new refcount_t refcount field. dma-buf is replaced by using anon_inode_getfd() instead, this separates the life-cycle of the underlying file from the tee_shm. tee_shm_put() is updated to hold the mutex when decreasing the refcount to 0 and then remove the tee_shm from teedev->idr before releasing the mutex. This means that the tee_shm can never be found unless it has a refcount larger than 0. Fixes: 967c9cca2cc5 ("tee: generic TEE subsystem") Cc: [email protected] Reviewed-by: Greg Kroah-Hartman <[email protected]> Reviewed-by: Lars Persson <[email protected]> Reviewed-by: Sumit Garg <[email protected]> Reported-by: Patrik Lantz <[email protected]> Signed-off-by: Jens Wiklander <[email protected]>
2021-12-16xen/netback: don't queue unlimited number of packagesJuergen Gross1-7/+11
In case a guest isn't consuming incoming network traffic as fast as it is coming in, xen-netback is buffering network packages in unlimited numbers today. This can result in host OOM situations. Commit f48da8b14d04ca8 ("xen-netback: fix unlimited guest Rx internal queue and carrier flapping") meant to introduce a mechanism to limit the amount of buffered data by stopping the Tx queue when reaching the data limit, but this doesn't work for cases like UDP. When hitting the limit don't queue further SKBs, but drop them instead. In order to be able to tell Rx packages have been dropped increment the rx_dropped statistics counter in this case. It should be noted that the old solution to continue queueing SKBs had the additional problem of an overflow of the 32-bit rx_queue_len value would result in intermittent Tx queue enabling. This is part of XSA-392 Fixes: f48da8b14d04ca8 ("xen-netback: fix unlimited guest Rx internal queue and carrier flapping") Signed-off-by: Juergen Gross <[email protected]> Reviewed-by: Jan Beulich <[email protected]>
2021-12-16xen/netback: fix rx queue stall detectionJuergen Gross2-24/+42
Commit 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when not using GSO") introduced a security problem in netback, as an interface would only be regarded to be stalled if no slot is available in the rx queue ring page. In case the SKB at the head of the queued requests will need more than one rx slot and only one slot is free the stall detection logic will never trigger, as the test for that is only looking for at least one slot to be free. Fix that by testing for the needed number of slots instead of only one slot being available. In order to not have to take the rx queue lock that often, store the number of needed slots in the queue data. As all SKB dequeue operations happen in the rx queue kernel thread this is safe, as long as the number of needed slots is accessed via READ/WRITE_ONCE() only and updates are always done with the rx queue lock held. Add a small helper for obtaining the number of free slots. This is part of XSA-392 Fixes: 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when not using GSO") Signed-off-by: Juergen Gross <[email protected]> Reviewed-by: Jan Beulich <[email protected]>
2021-12-16xen/console: harden hvc_xen against event channel stormsJuergen Gross3-3/+34
The Xen console driver is still vulnerable for an attack via excessive number of events sent by the backend. Fix that by using a lateeoi event channel. For the normal domU initial console this requires the introduction of bind_evtchn_to_irq_lateeoi() as there is no xenbus device available at the time the event channel is bound to the irq. As the decision whether an interrupt was spurious or not requires to test for bytes having been read from the backend, move sending the event into the if statement, as sending an event without having found any bytes to be read is making no sense at all. This is part of XSA-391 Signed-off-by: Juergen Gross <[email protected]> Reviewed-by: Jan Beulich <[email protected]> --- V2: - slightly adapt spurious irq detection (Jan Beulich) V3: - fix spurious irq detection (Jan Beulich)
2021-12-16xen/netfront: harden netfront against event channel stormsJuergen Gross1-31/+94
The Xen netfront driver is still vulnerable for an attack via excessive number of events sent by the backend. Fix that by using lateeoi event channels. For being able to detect the case of no rx responses being added while the carrier is down a new lock is needed in order to update and test rsp_cons and the number of seen unconsumed responses atomically. This is part of XSA-391 Signed-off-by: Juergen Gross <[email protected]> Reviewed-by: Jan Beulich <[email protected]> --- V2: - don't eoi irq in case of interface set broken (Jan Beulich) - handle carrier off + no new responses added (Jan Beulich) V3: - add rx_ prefix to rsp_unconsumed (Jan Beulich) - correct xennet_set_rx_rsp_cons() spelling (Jan Beulich)
2021-12-16xen/blkfront: harden blkfront against event channel stormsJuergen Gross1-3/+12
The Xen blkfront driver is still vulnerable for an attack via excessive number of events sent by the backend. Fix that by using lateeoi event channels. This is part of XSA-391 Signed-off-by: Juergen Gross <[email protected]> Reviewed-by: Jan Beulich <[email protected]>
2021-12-16ARM: dts: imx6qdl-wandboard: Fix Ethernet supportMartin Haaß1-0/+1
Currently, the imx6q-wandboard Ethernet does not transmit any data. This issue has been exposed by commit f5d9aa79dfdf ("ARM: imx6q: remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs"). Fix it by describing the qca,clk-out-frequency property as suggested by the commit above. Fixes: 77591e42458d ("ARM: dts: imx6qdl-wandboard: add ethernet PHY description") Signed-off-by: Martin Haaß <[email protected]> Tested-by: Fabio Estevam <[email protected]> Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2021-12-16pinctrl: stm32: consider the GPIO offset to expose all the GPIO linesFabien Dessenne1-4/+4
Consider the GPIO controller offset (from "gpio-ranges") to compute the maximum GPIO line number. This fixes an issue where gpio-ranges uses a non-null offset. e.g.: gpio-ranges = <&pinctrl 6 86 10> In that case the last valid GPIO line is not 9 but 15 (6 + 10 - 1) Cc: [email protected] Fixes: 67e2996f72c7 ("pinctrl: stm32: fix the reported number of GPIO lines per bank") Reported-by: Christoph Fritz <[email protected]> Signed-off-by: Fabien Dessenne <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.