| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
An exception is seen in ICMP ping receive path where the skb
destructor sock_rfree() tries to access a freed socket. This happens
because ping_rcv() releases socket reference with sock_put() and this
internally frees up the socket. Later icmp_rcv() will try to free the
skb and as part of this, skb destructor is called and which leads
to a kernel panic as the socket is freed already in ping_rcv().
-->|exception
-007|sk_mem_uncharge
-007|sock_rfree
-008|skb_release_head_state
-009|skb_release_all
-009|__kfree_skb
-010|kfree_skb
-011|icmp_rcv
-012|ip_local_deliver_finish
Fix this incorrect free by cloning this skb and processing this cloned
skb instead.
This patch was suggested by Eric Dumazet
Signed-off-by: Subash Abhinov Kasiviswanathan <[email protected]>
Cc: Eric Dumazet <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
While working on rhashtable walking I noticed that the UDP diag
dumping code is buggy. In particular, the socket skipping within
a chain never happens, even though we record the number of sockets
that should be skipped.
As this code was supposedly copied from TCP, this patch does what
TCP does and resets num before we walk a chain.
Signed-off-by: Herbert Xu <[email protected]>
Acked-by: Pavel Emelyanov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
While being in an ERROR_WARNING state, and receiving further
bus error events with error counters still in the ERROR_WARNING
range of 97-127 inclusive, the state handling code erroneously
reverts back to ERROR_ACTIVE.
Per the CAN standard, only revert to ERROR_ACTIVE when the
error counters are less than 96.
Moreover, in certain Kvaser models, the BUS_ERROR flag is
always set along with undefined bits in the M16C status
register. Thus use bitwise operators instead of full equality
for checking that register against bus errors.
Signed-off-by: Ahmed S. Darwish <[email protected]>
Cc: linux-stable <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
On some x86 laptops, plugging a Kvaser device again after an
unplug makes the firmware always ignore the very first command.
For such a case, provide some room for retries instead of
completely exiting the driver init code.
Signed-off-by: Ahmed S. Darwish <[email protected]>
Cc: linux-stable <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Send expected argument to the URB completion hander: a CAN
netdevice instead of the network interface private context
`kvaser_usb_net_priv'.
This was discovered by having some garbage in the kernel
log in place of the netdevice names: can0 and can1.
Signed-off-by: Ahmed S. Darwish <[email protected]>
Cc: linux-stable <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Upon receiving a hardware event with the BUS_RESET flag set,
the driver kills all of its anchored URBs and resets all of
its transmit URB contexts.
Unfortunately it does so under the context of URB completion
handler `kvaser_usb_read_bulk_callback()', which is often
called in an atomic context.
While the device is flooded with many received error packets,
usb_kill_urb() typically sleeps/reschedules till the transfer
request of each killed URB in question completes, leading to
the sleep in atomic bug. [3]
In v2 submission of the original driver patch [1], it was
stated that the URBs kill and tx contexts reset was needed
since we don't receive any tx acknowledgments later and thus
such resources will be locked down forever. Fortunately this
is no longer needed since an earlier bugfix in this patch
series is now applied: all tx URB contexts are reset upon CAN
channel close. [2]
Moreover, a BUS_RESET is now treated _exactly_ like a BUS_OFF
event, which is the recommended handling method advised by
the device manufacturer.
[1] http://article.gmane.org/gmane.linux.network/239442
http://www.webcitation.org/6Vr2yagAQ
[2] can: kvaser_usb: Reset all URB tx contexts upon channel close
889b77f7fd2bcc922493d73a4c51d8a851505815
[3] Stacktrace:
<IRQ> [<ffffffff8158de87>] dump_stack+0x45/0x57
[<ffffffff8158b60c>] __schedule_bug+0x41/0x4f
[<ffffffff815904b1>] __schedule+0x5f1/0x700
[<ffffffff8159360a>] ? _raw_spin_unlock_irqrestore+0xa/0x10
[<ffffffff81590684>] schedule+0x24/0x70
[<ffffffff8147d0a5>] usb_kill_urb+0x65/0xa0
[<ffffffff81077970>] ? prepare_to_wait_event+0x110/0x110
[<ffffffff8147d7d8>] usb_kill_anchored_urbs+0x48/0x80
[<ffffffffa01f4028>] kvaser_usb_unlink_tx_urbs+0x18/0x50 [kvaser_usb]
[<ffffffffa01f45d0>] kvaser_usb_rx_error+0xc0/0x400 [kvaser_usb]
[<ffffffff8108b14a>] ? vprintk_default+0x1a/0x20
[<ffffffffa01f5241>] kvaser_usb_read_bulk_callback+0x4c1/0x5f0 [kvaser_usb]
[<ffffffff8147a73e>] __usb_hcd_giveback_urb+0x5e/0xc0
[<ffffffff8147a8a1>] usb_hcd_giveback_urb+0x41/0x110
[<ffffffffa0008748>] finish_urb+0x98/0x180 [ohci_hcd]
[<ffffffff810cd1a7>] ? acct_account_cputime+0x17/0x20
[<ffffffff81069f65>] ? local_clock+0x15/0x30
[<ffffffffa000a36b>] ohci_work+0x1fb/0x5a0 [ohci_hcd]
[<ffffffff814fbb31>] ? process_backlog+0xb1/0x130
[<ffffffffa000cd5b>] ohci_irq+0xeb/0x270 [ohci_hcd]
[<ffffffff81479fc1>] usb_hcd_irq+0x21/0x30
[<ffffffff8108bfd3>] handle_irq_event_percpu+0x43/0x120
[<ffffffff8108c0ed>] handle_irq_event+0x3d/0x60
[<ffffffff8108ec84>] handle_fasteoi_irq+0x74/0x110
[<ffffffff81004dfd>] handle_irq+0x1d/0x30
[<ffffffff81004727>] do_IRQ+0x57/0x100
[<ffffffff8159482a>] common_interrupt+0x6a/0x6a
Signed-off-by: Ahmed S. Darwish <[email protected]>
Cc: linux-stable <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Another set of last-minute fixes:
* fix station double-removal when suspending while associating
* fix the HT (802.11n) header length calculation
* fix the CCK radiotap flag used for monitoring, a pretty
old regression but a simple one-liner
* fix per-station group-key handling
Signed-off-by: David S. Miller <[email protected]>
|
|
Not caching dst_entries which cause redirects could be exploited by hosts
on the same subnet, causing a severe DoS attack. This effect aggravated
since commit f88649721268999 ("ipv4: fix dst race in sk_dst_get()").
Lookups causing redirects will be allocated with DST_NOCACHE set which
will force dst_release to free them via RCU. Unfortunately waiting for
RCU grace period just takes too long, we can end up with >1M dst_entries
waiting to be released and the system will run OOM. rcuos threads cannot
catch up under high softirq load.
Attaching the flag to emit a redirect later on to the specific skb allows
us to cache those dst_entries thus reducing the pressure on allocation
and deallocation.
This issue was discovered by Marcelo Leitner.
Cc: Julian Anastasov <[email protected]>
Signed-off-by: Marcelo Leitner <[email protected]>
Signed-off-by: Florian Westphal <[email protected]>
Signed-off-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: Julian Anastasov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Alexei Starovoitov says:
====================
bpf: fix two bugs
Michael Holzheu caught two issues (in bpf syscall and in the test).
Fix them. Details in corresponding patches.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
hash map is unordered, so get_next_key() iterator shouldn't
rely on particular order of elements. So relax this test.
Fixes: ffb65f27a155 ("bpf: add a testsuite for eBPF maps")
Reported-by: Michael Holzheu <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
Acked-by: Daniel Borkmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
BUG: sleeping function called from invalid context at mm/memory.c:3732
in_atomic(): 0, irqs_disabled(): 0, pid: 671, name: test_maps
1 lock held by test_maps/671:
#0: (rcu_read_lock){......}, at: [<0000000000264190>] map_lookup_elem+0xe8/0x260
Call Trace:
([<0000000000115b7e>] show_trace+0x12e/0x150)
[<0000000000115c40>] show_stack+0xa0/0x100
[<00000000009b163c>] dump_stack+0x74/0xc8
[<000000000017424a>] ___might_sleep+0x23a/0x248
[<00000000002b58e8>] might_fault+0x70/0xe8
[<0000000000264230>] map_lookup_elem+0x188/0x260
[<0000000000264716>] SyS_bpf+0x20e/0x840
Fix it by allocating temporary buffer to store map element value.
Fixes: db20fd2b0108 ("bpf: add lookup/update/delete/iterate methods to BPF maps")
Reported-by: Michael Holzheu <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
Acked-by: Daniel Borkmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When hitting an INIT collision case during the 4WHS with AUTH enabled, as
already described in detail in commit 1be9a950c646 ("net: sctp: inherit
auth_capable on INIT collisions"), it can happen that we occasionally
still remotely trigger the following panic on server side which seems to
have been uncovered after the fix from commit 1be9a950c646 ...
[ 533.876389] BUG: unable to handle kernel paging request at 00000000ffffffff
[ 533.913657] IP: [<ffffffff811ac385>] __kmalloc+0x95/0x230
[ 533.940559] PGD 5030f2067 PUD 0
[ 533.957104] Oops: 0000 [#1] SMP
[ 533.974283] Modules linked in: sctp mlx4_en [...]
[ 534.939704] Call Trace:
[ 534.951833] [<ffffffff81294e30>] ? crypto_init_shash_ops+0x60/0xf0
[ 534.984213] [<ffffffff81294e30>] crypto_init_shash_ops+0x60/0xf0
[ 535.015025] [<ffffffff8128c8ed>] __crypto_alloc_tfm+0x6d/0x170
[ 535.045661] [<ffffffff8128d12c>] crypto_alloc_base+0x4c/0xb0
[ 535.074593] [<ffffffff8160bd42>] ? _raw_spin_lock_bh+0x12/0x50
[ 535.105239] [<ffffffffa0418c11>] sctp_inet_listen+0x161/0x1e0 [sctp]
[ 535.138606] [<ffffffff814e43bd>] SyS_listen+0x9d/0xb0
[ 535.166848] [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b
... or depending on the the application, for example this one:
[ 1370.026490] BUG: unable to handle kernel paging request at 00000000ffffffff
[ 1370.026506] IP: [<ffffffff811ab455>] kmem_cache_alloc+0x75/0x1d0
[ 1370.054568] PGD 633c94067 PUD 0
[ 1370.070446] Oops: 0000 [#1] SMP
[ 1370.085010] Modules linked in: sctp kvm_amd kvm [...]
[ 1370.963431] Call Trace:
[ 1370.974632] [<ffffffff8120f7cf>] ? SyS_epoll_ctl+0x53f/0x960
[ 1371.000863] [<ffffffff8120f7cf>] SyS_epoll_ctl+0x53f/0x960
[ 1371.027154] [<ffffffff812100d3>] ? anon_inode_getfile+0xd3/0x170
[ 1371.054679] [<ffffffff811e3d67>] ? __alloc_fd+0xa7/0x130
[ 1371.080183] [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b
With slab debugging enabled, we can see that the poison has been overwritten:
[ 669.826368] BUG kmalloc-128 (Tainted: G W ): Poison overwritten
[ 669.826385] INFO: 0xffff880228b32e50-0xffff880228b32e50. First byte 0x6a instead of 0x6b
[ 669.826414] INFO: Allocated in sctp_auth_create_key+0x23/0x50 [sctp] age=3 cpu=0 pid=18494
[ 669.826424] __slab_alloc+0x4bf/0x566
[ 669.826433] __kmalloc+0x280/0x310
[ 669.826453] sctp_auth_create_key+0x23/0x50 [sctp]
[ 669.826471] sctp_auth_asoc_create_secret+0xcb/0x1e0 [sctp]
[ 669.826488] sctp_auth_asoc_init_active_key+0x68/0xa0 [sctp]
[ 669.826505] sctp_do_sm+0x29d/0x17c0 [sctp] [...]
[ 669.826629] INFO: Freed in kzfree+0x31/0x40 age=1 cpu=0 pid=18494
[ 669.826635] __slab_free+0x39/0x2a8
[ 669.826643] kfree+0x1d6/0x230
[ 669.826650] kzfree+0x31/0x40
[ 669.826666] sctp_auth_key_put+0x19/0x20 [sctp]
[ 669.826681] sctp_assoc_update+0x1ee/0x2d0 [sctp]
[ 669.826695] sctp_do_sm+0x674/0x17c0 [sctp]
Since this only triggers in some collision-cases with AUTH, the problem at
heart is that sctp_auth_key_put() on asoc->asoc_shared_key is called twice
when having refcnt 1, once directly in sctp_assoc_update() and yet again
from within sctp_auth_asoc_init_active_key() via sctp_assoc_update() on
the already kzfree'd memory, which is also consistent with the observation
of the poison decrease from 0x6b to 0x6a (note: the overwrite is detected
at a later point in time when poison is checked on new allocation).
Reference counting of auth keys revisited:
Shared keys for AUTH chunks are being stored in endpoints and associations
in endpoint_shared_keys list. On endpoint creation, a null key is being
added; on association creation, all endpoint shared keys are being cached
and thus cloned over to the association. struct sctp_shared_key only holds
a pointer to the actual key bytes, that is, struct sctp_auth_bytes which
keeps track of users internally through refcounting. Naturally, on assoc
or enpoint destruction, sctp_shared_key are being destroyed directly and
the reference on sctp_auth_bytes dropped.
User space can add keys to either list via setsockopt(2) through struct
sctp_authkey and by passing that to sctp_auth_set_key() which replaces or
adds a new auth key. There, sctp_auth_create_key() creates a new sctp_auth_bytes
with refcount 1 and in case of replacement drops the reference on the old
sctp_auth_bytes. A key can be set active from user space through setsockopt()
on the id via sctp_auth_set_active_key(), which iterates through either
endpoint_shared_keys and in case of an assoc, invokes (one of various places)
sctp_auth_asoc_init_active_key().
sctp_auth_asoc_init_active_key() computes the actual secret from local's
and peer's random, hmac and shared key parameters and returns a new key
directly as sctp_auth_bytes, that is asoc->asoc_shared_key, plus drops
the reference if there was a previous one. The secret, which where we
eventually double drop the ref comes from sctp_auth_asoc_set_secret() with
intitial refcount of 1, which also stays unchanged eventually in
sctp_assoc_update(). This key is later being used for crypto layer to
set the key for the hash in crypto_hash_setkey() from sctp_auth_calculate_hmac().
To close the loop: asoc->asoc_shared_key is freshly allocated secret
material and independant of the sctp_shared_key management keeping track
of only shared keys in endpoints and assocs. Hence, also commit 4184b2a79a76
("net: sctp: fix memory leak in auth key management") is independant of
this bug here since it concerns a different layer (though same structures
being used eventually). asoc->asoc_shared_key is reference dropped correctly
on assoc destruction in sctp_association_free() and when active keys are
being replaced in sctp_auth_asoc_init_active_key(), it always has a refcount
of 1. Hence, it's freed prematurely in sctp_assoc_update(). Simple fix is
to remove that sctp_auth_key_put() from there which fixes these panics.
Fixes: 730fc3d05cd4 ("[SCTP]: Implete SCTP-AUTH parameter processing")
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Vlad Yasevich <[email protected]>
Acked-by: Neil Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Merge misc fixes from Andrew Morton:
"Six fixes"
* emailed patches from Andrew Morton <[email protected]>:
drivers/rtc/rtc-s5m.c: terminate s5m_rtc_id array with empty element
printk: add dummy routine for when CONFIG_PRINTK=n
mm/vmscan: fix highidx argument type
memcg: remove extra newlines from memcg oom kill log
x86, build: replace Perl script with Shell script
mm: page_alloc: embed OOM killing naturally into allocation slowpath
|
|
Commit 69ad0dd7af22b61d9e0e68e56b6290121618b0fb
Author: Ezequiel Garcia <[email protected]>
Date: Mon May 19 13:59:59 2014 -0300
net: mv643xx_eth: Use dma_map_single() to map the skb fragments
caused a nasty regression by removing the support for highmem skb
fragments. By using page_address() to get the address of a fragment's
page, we are assuming a lowmem page. However, such assumption is incorrect,
as fragments can be in highmem pages, resulting in very nasty issues.
This commit fixes this by using the skb_frag_dma_map() helper,
which takes care of mapping the skb fragment properly. Additionally,
the type of mapping is now tracked, so it can be unmapped using
dma_unmap_page or dma_unmap_single when appropriate.
This commit also fixes the error path in txq_init() to release the
resources properly.
Fixes: 69ad0dd7af22 ("net: mv643xx_eth: Use dma_map_single() to map the skb fragments")
Reported-by: Russell King <[email protected]>
Signed-off-by: Ezequiel Garcia <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Ben Hutchings says:
====================
Fixes for sh_eth #2
I'm continuing review and testing of Ethernet support on the R-Car H2
chip. This series fixes more of the issues I've found, but it won't be
the last set.
These are not tested on any of the other supported chips.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
In order to stop the RX path accessing the RX ring while it's being
stopped or resized, we clear the interrupt mask (EESIPR) and then call
free_irq() or synchronise_irq(). This is insufficient because the
interrupt handler or NAPI poller may set EESIPR again after we clear
it. Also, in sh_eth_set_ringparam() we currently don't disable NAPI
polling at all.
I could easily trigger a crash by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine.
To fix this:
- Add a software flag (irq_enabled) to signal whether interrupts
should be enabled
- In the interrupt handler, if the flag is clear then clear EESIPR
and return
- In the NAPI poller, if the flag is clear then don't set EESIPR
- Set the flag before enabling interrupts in sh_eth_dev_init() and
sh_eth_set_ringparam()
- Clear the flag and serialise with the interrupt and NAPI
handlers before clearing EESIPR in sh_eth_close() and
sh_eth_set_ringparam()
After this, I could run the loop for 100,000 iterations successfully.
Signed-off-by: Ben Hutchings <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If the device is down then no packet buffers should be allocated.
We also must not touch its registers as it may be powered off.
Signed-off-by: Ben Hutchings <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.
I could easily trigger this by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
Signed-off-by: Ben Hutchings <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding. This could result in leaking sensitive
data. We also pass different lengths to dma_map_single() and
dma_unmap_single().
Use skb_padto() to pad properly, before calling dma_map_single().
Signed-off-by: Ben Hutchings <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.
Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.
Fixes: d9ba8f9e6298 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <[email protected]> # v3.9+
Reported-by: Felipe Balbi <[email protected]>
Signed-off-by: Mugunthan V N <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
into drm-next
single rockchip fix.
* 'drm-next' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: fix dma_alloc_attrs() error check
|
|
into drm-fixes
Suspend/resume regression fix for 3.19.
* 'drm-fixes-3.19' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Remove rdev->gart.pages_addr array
drm/radeon: Restore GART table contents after pinning it in VRAM v3
drm/radeon: Split off gart_get_page_entry ASIC hook from set_page_entry
|
|
Daniel Borkmann says:
====================
Two cls_bpf fixes
Found them while doing a review on act_bpf and going over the
cls_bpf code again. Will also address the first issue in act_bpf
as it needs to be fixed there, too.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
When creating a bpf classifier in tc with priority collisions and
invoking automatic unique handle assignment, cls_bpf_grab_new_handle()
will return a wrong handle id which in fact is non-unique. Usually
altering of specific filters is being addressed over major id, but
in case of collisions we result in a filter chain, where handle ids
address individual cls_bpf_progs inside the classifier.
Issue is, in cls_bpf_grab_new_handle() we probe for head->hgen handle
in cls_bpf_get() and in case we found a free handle, we're supposed
to use exactly head->hgen. In case of insufficient numbers of handles,
we bail out later as handle id 0 is not allowed.
Fixes: 7d1d65cb84e1 ("net: sched: cls_bpf: add BPF-based classifier")
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In cls_bpf_modify_existing(), we read out the number of filter blocks,
do some sanity checks, allocate a block on that size, and copy over the
BPF instruction blob from user space, then pass everything through the
classic BPF checker prior to installation of the classifier.
We should reject mismatches here, there are 2 scenarios: the number of
filter blocks could be smaller than the provided instruction blob, so
we do a partial copy of the BPF program, and thus the instructions will
either be rejected from the verifier or a valid BPF program will be run;
in the other case, we'll end up copying more than we're supposed to,
and most likely the trailing garbage will be rejected by the verifier
as well (i.e. we need to fit instruction pattern, ret {A,K} needs to be
last instruction, load/stores must be correct, etc); in case not, we
would leak memory when dumping back instruction patterns. The code should
have only used nla_len() as Dave noted to avoid this from the beginning.
Anyway, lets fix it by rejecting such load attempts.
Fixes: 7d1d65cb84e1 ("net: sched: cls_bpf: add BPF-based classifier")
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://people.freedesktop.org/~gabbayo/linux into drm-fixes
A couple of fixes for -rc7 in amdkfd:
- Forgot to free resources when creation of queue has failed
- Initialization of pipelines was incorrect (3 patches)
In addition, The patch "drm/amdkfd: Allow user to limit only queues per device"
is not a fix, but I would like to push it for 3.19 as it changes the ABI
between amdkfd and userspace (by changing the module parameters). I would
prefer *not* to support the two deprecated module parameters if I don't have
too, as amdkfd hasn't been released yet.
* tag 'drm-amdkfd-fixes-2015-01-26' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Fix bug in call to init_pipelines()
drm/amdkfd: Fix bug in pipelines initialization
drm/radeon: Don't increment pipe_id in kgd_init_pipeline
drm/amdkfd: Allow user to limit only queues per device
drm/amdkfd: PQM handle queue creation fault
|
|
Linux 3.19-rc6
pull in rc6 as the amdkfd fixes are based on it, and I'd rather
be doing the merges separately
|
|
into drm-next
Radeon drm-next changes for 3.20. Highlights:
- Indirect draw support for evergreen/NI hw
- SMC fan control support for SI/CI
- Manual fan control for SI/CI
- DP audio support
- Lots of code cleanup
* 'drm-next-3.20' of git://people.freedesktop.org/~agd5f/linux: (45 commits)
drm/radeon: make MMU_NOTIFIER optional
drm/radeon: use NULL rather then 0 in audio detect
drm/radeon: whitespace clean up in radeon_audio.c
radeon/audio: enable DP audio
radeon/audio: moved audio caps programming to audio_hotplug() function
radeon/audio: applied audio_dpms() and audio_mode_set() calls
radeon/audio: consolidate audio_mode_set() functions
radeon/audio: removed unnecessary debug settings
radeon/audio: moved mute programming to a separate function
radeon/audio: moved audio packet programming to a separate function
radeon/audio: set_avi_packet() function cleanup
radeon/audio: removed unnecessary CRC control programing
radeon: moved HDMI color depth programming to a separate function
radeon/audio: moved VBI packet programming to separate functions
radeon/audio: consolidate update_acr() functions (v2)
radeon/audio: consolidate update_avi_infoframe() functions
radeon/audio: consolidate audio_set_dto() functions
radeon/audio: consolidate audio_fini() functions
radeon/audio: consolidate audio_enable() functions
radeon/audio: consolidate select_pin() functions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
This pull request includes some code refactoring which removes
Exynos specific structure names and uses generic structure
names instead, and makes all plane updating to be done
by only exynos_update_plane function. And also it includes
some cleanup and fixup patches.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos: (22 commits)
drm/exynos: fimd: check error status for drm_iommu_attach_device
drm/exynos: create exynos_check_plane()
drm/exynos: remove mode_set() ops from exynos_crtc
drm/exynos: don't duplicate drm_display_mode in fimd context
drm/exynos: remove struct exynos_drm_manager
drm/exynos: remove drm_dev from struct exynos_drm_manager
drm/exynos: move 'type' from manager to crtc struct
drm/exynos: remove pipe member of struct exynos_drm_manager
drm/exynos: add pipe param to exynos_drm_crtc_create()
drm/exynos: rename base object of struct exynos_drm_crtc to 'base'
drm/exynos: remove exynos_drm_crtc_mode_set_commit()
drm/exynos: call exynos_update_plane() directly on page flips
drm/exynos: unify plane update on exynos_update_plane()
drm/exynos: remove exynos_plane_commit() wrapper
drm/exynos: don't do any DPMS operation while updating planes
drm/exynos: Don't touch DPMS when updating overlay planes
drm/exynos/vidi: remove useless ops->commit()
drm/exynos/fimd: don't initialize 'ret' variable in fimd_probe()
drm/exynos: remove struct exynos_drm_overlay
drm/exynos: remove exynos_drm_crtc_plane_* wrappers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-01-21
this is a pull request for v3.19, net/master, which consists of a single patch.
Viktor Babrian fixes the issue in the c_can dirver, that the CAN interface
might continue to send frames after the interface has been shut down.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"The lifetime rules of cgroup hierarchies always have been somewhat
counter-intuitive and cgroup core tried to enforce that hierarchies
w/o userland-visible usages must die in finite amount of time so that
the controllers can be reused for other hierarchies; unfortunately,
this can't be implemented reasonably for the memory controller - the
kmemcg part doesn't have any way to forcefully drain the existing
usages, leading to an interruptible hang if a following mount attempts
to use the controller in any way.
So, it seems like we're stuck with "hierarchies live on till they die
whenever that may be" at least for now. This pretty much confines
attaching controllers to hierarchies to before the hierarchies are
actively used by making dynamic configurations post active usages
unreliable. This has never been reliable and should be fine in
practice given how cgroups are used.
After the patch, hierarchies aren't killed if it isn't already
drained. A following mount attempt of the same mount options will
reuse the existing hierarchy. Mount attempts with differing options
will fail w/ -EBUSY"
* 'for-3.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: prevent mount hang due to memory controller lifetime
|
|
git://people.freedesktop.org/~gabbayo/linux into drm-next
Here is a pull request of fixes for 3.20 patches, including the fix you asked
me when you merged the previous pull request.
* tag 'drm-amdkfd-next-fixes-2015-01-25' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: change amdkfd version to 0.7.1
drm/radeon: cik_sdma_ctx_switch_enable() can be static
drm/amdkfd: Fix sparse errors
drm/amdkfd: Handle case of invalid queue type
drm/amdkfd: Add break at the end of case
drm/amdkfd: Remove negative check of uint variable
|
|
git://ftp.arm.linux.org.uk/~rmk/linux-arm into drm-fixes
3 fixes for the tda998x.
* 'drm-tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: set the CEC I2C address based on the slave I2C address
drm: tda998x: Fix EDID read timeout on HDMI connect
drm: tda998x: Protect the page register
|
|
formats and num_formats arguments were previously called fmts and nfmts.
Fix the kernel doc comment so that it matches the new argument names.
Signed-off-by: Boris Brezillon <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
- refactor i915/snd-hda interaction to use the component framework (Imre)
- psr cleanups and small fixes (Rodrigo)
- a few perf w/a from Ken Graunke
- switch to atomic plane helpers (Matt Roper)
- wc mmap support (Chris Wilson & Akash Goel)
- smaller things all over
* tag 'drm-intel-next-2015-01-17' of git://anongit.freedesktop.org/drm-intel: (40 commits)
drm/i915: Update DRIVER_DATE to 20150117
i915: reuse %ph to dump small buffers
drm/i915: Ensure the HiZ RAW Stall Optimization is on for Cherryview.
drm/i915: Enable the HiZ RAW Stall Optimization on Broadwell.
drm/i915: PSR link standby at debugfs
drm/i915: group link_standby setup and let this info visible everywhere.
drm/i915: Add missing vbt check.
drm/i915: PSR HSW/BDW: Fix inverted logic at sink main_link_active bit.
drm/i915: PSR VLV/CHV: Remove condition checks that only applies to Haswell.
drm/i915: VLV/CHV PSR needs to exit PSR on every flush.
drm/i915: Fix kerneldoc for i915 atomic plane code
drm/i915: Don't pretend SDVO hotplug works on 915
drm/i915: Don't register HDMI connectors for eDP ports on VLV/CHV
drm/i915: Remove I915_HAS_HOTPLUG() check from i915_hpd_irq_setup()
drm/i915: Make hpd arrays big enough to avoid out of bounds access
Revert "drm/i915/chv: Use timeout mode for RC6 on chv"
drm/i915: Improve HiZ throughput on Cherryview.
drm/i915: Reset CSB read pointer in ring init
drm/i915: Drop unused position fields (v2)
drm/i915: Move to atomic plane helpers (v9)
...
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
Just flushing out my drm-misc branch, nothing major. Well too old patches
I've dug out from years since a patch from Rob look eerily familiar ;-)
* tag 'topic/core-stuff-2015-01-23' of git://anongit.freedesktop.org/drm-intel:
drm/probe-helper: clamp unknown connector status in the poll work
drm/probe-helper: don't lose hotplug event
next: drm/atomic: Use copy_from_user to copy 64 bit data from user space
drm: Make drm_read() more robust against multithreaded races
drm/fb-helper: Propagate errors from initial config failure
drm: Drop superfluous "select VT_HW_CONSOLE_BINDING"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One correctness fix here for the s2mps11 driver which would have
resulted in some of the regulators being completely broken together
with a fix for locking in regualtor_put() (which is fortunately rarely
called at all in practical systems)"
* tag 'regulator-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mps11: Fix wrong calculation of register offset
regulator: core: fix race condition in regulator_put()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes here, some fixes for issues introduced and
discovered during recent work on the DesignWare driver (which has been
getting a lot of attention recently) and a couple of other drivers.
All serious things for people who run into them"
* tag 'spi-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dw: amend warning message
spi: sh-msiof: fix MDR1_FLD_MASK value
spi: dw-mid: fix FIFO size
spi: dw: Fix detecting FIFO depth
spi/pxa2xx: Clear cur_chip pointer before starting next message
|
|
Array of platform_device_id elements should be terminated with empty
element.
Fixes: 5bccae6ec458 ("rtc: s5m-rtc: add real-time clock driver for s5m8767")
Signed-off-by: Andrey Ryabinin <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
There are missing dummy routines for log_buf_addr_get() and
log_buf_len_get() for when CONFIG_PRINTK is not set causing build
failures.
This patch adds these dummy routines at the appropriate location.
Signed-off-by: Pranith Kumar <[email protected]>
Cc: Michael Ellerman <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Acked-by: Steven Rostedt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
for_each_zone_zonelist_nodemask wants an enum zone_type argument, but is
passed gfp_t:
mm/vmscan.c:2658:9: expected int enum zone_type [signed] highest_zoneidx
mm/vmscan.c:2658:9: got restricted gfp_t [usertype] gfp_mask
mm/vmscan.c:2658:9: warning: incorrect type in argument 2 (different base types)
mm/vmscan.c:2658:9: expected int enum zone_type [signed] highest_zoneidx
mm/vmscan.c:2658:9: got restricted gfp_t [usertype] gfp_mask
convert argument to the correct type.
Signed-off-by: Michael S. Tsirkin <[email protected]>
Cc: Johannes Weiner <[email protected]>
Cc: Vladimir Davydov <[email protected]>
Cc: Rik van Riel <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: Suleiman Souhlal <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Commit e61734c55c24 ("cgroup: remove cgroup->name") added two extra
newlines to memcg oom kill log messages. This makes dmesg hard to read
and parse. The issue affects 3.15+.
Example:
Task in /t <<< extra #1
killed as a result of limit of /t
<<< extra #2
memory: usage 102400kB, limit 102400kB, failcnt 274712
Remove the extra newlines from memcg oom kill messages, so the messages
look like:
Task in /t killed as a result of limit of /t
memory: usage 102400kB, limit 102400kB, failcnt 240649
Fixes: e61734c55c24 ("cgroup: remove cgroup->name")
Signed-off-by: Greg Thelen <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Acked-by: Johannes Weiner <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Commit e6023367d779 ("x86, kaslr: Prevent .bss from overlaping initrd")
added Perl to the required build environment. This reimplements in
shell the Perl script used to find the size of the kernel with bss and
brk added.
Signed-off-by: Kees Cook <[email protected]>
Reported-by: Rob Landley <[email protected]>
Acked-by: Rob Landley <[email protected]>
Cc: Anca Emanuel <[email protected]>
Cc: Fengguang Wu <[email protected]>
Cc: Junjie Mao <[email protected]>
Cc: Kees Cook <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The OOM killing invocation does a lot of duplicative checks against the
task's allocation context. Rework it to take advantage of the existing
checks in the allocator slowpath.
The OOM killer is invoked when the allocator is unable to reclaim any
pages but the allocation has to keep looping. Instead of having a check
for __GFP_NORETRY hidden in oom_gfp_allowed(), just move the OOM
invocation to the true branch of should_alloc_retry(). The __GFP_FS
check from oom_gfp_allowed() can then be moved into the OOM avoidance
branch in __alloc_pages_may_oom(), along with the PF_DUMPCORE test.
__alloc_pages_may_oom() can then signal to the caller whether the OOM
killer was invoked, instead of requiring it to duplicate the order and
high_zoneidx checks to guess this when deciding whether to continue.
Signed-off-by: Johannes Weiner <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Cc: David Rientjes <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
'spi/fix/pxa2xx' into spi-linus
|
|
Ursula Braun says:
====================
s390/qeth patches for net
here are two s390/qeth patches built for net.
One patch is quite large, but we would like to fix the locking warning
seen in recent kernels as soon as possible. But if you want me to submit
these patches for net-next, I will do.
Or Gerlitz says:
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Do not wait for channel command buffers in IPA commands.
The potential wait could be done while holding a spin lock and causes
in recent kernels such a bug if kernel lock debugging is enabled:
kernel: BUG: sleeping function called from invalid context at drivers/s390/net/qeth_core_main.c:
794
kernel: in_atomic(): 1, irqs_disabled(): 0, pid: 2031, name: NetworkManager
kernel: 2 locks held by NetworkManager/2031:
kernel: #0: (rtnl_mutex){+.+.+.}, at: [<00000000006e0d7a>] rtnetlink_rcv+0x32/0x50
kernel: #1: (_xmit_ETHER){+.....}, at: [<00000000006cfe90>] dev_set_rx_mode+0x30/0x50
kernel: CPU: 0 PID: 2031 Comm: NetworkManager Not tainted 3.18.0-rc5-next-20141124 #1
kernel: 00000000275fb1f0 00000000275fb280 0000000000000002 0000000000000000
00000000275fb320 00000000275fb298 00000000275fb298 00000000007e326a
0000000000000000 000000000099ce2c 00000000009b4988 000000000000000b
00000000275fb2e0 00000000275fb280 0000000000000000 0000000000000000
0000000000000000 00000000001129c8 00000000275fb280 00000000275fb2e0
kernel: Call Trace:
kernel: ([<00000000001128b0>] show_trace+0xf8/0x158)
kernel: [<000000000011297a>] show_stack+0x6a/0xe8
kernel: [<00000000007e995a>] dump_stack+0x82/0xb0
kernel: [<000000000017d668>] ___might_sleep+0x170/0x228
kernel: [<000003ff80026f0e>] qeth_wait_for_buffer+0x36/0xd0 [qeth]
kernel: [<000003ff80026fe2>] qeth_get_ipacmd_buffer+0x3a/0xc0 [qeth]
kernel: [<000003ff80105078>] qeth_l3_send_setdelmc+0x58/0xf8 [qeth_l3]
kernel: [<000003ff8010b1fe>] qeth_l3_set_ip_addr_list+0x2c6/0x848 [qeth_l3]
kernel: [<000003ff8010bbb4>] qeth_l3_set_multicast_list+0x434/0xc48 [qeth_l3]
kernel: [<00000000006cfe9a>] dev_set_rx_mode+0x3a/0x50
kernel: [<00000000006cff90>] __dev_open+0xe0/0x140
kernel: [<00000000006d02a0>] __dev_change_flags+0xa0/0x178
kernel: [<00000000006d03a8>] dev_change_flags+0x30/0x70
kernel: [<00000000006e14ee>] do_setlink+0x346/0x9a0
...
The device driver has plenty of command buffers available
per channel for channel command communication.
In the extremely rare case when there is no command buffer
available, return a NULL pointer and issue a warning
in the kernel log. The caller handles the case when
a NULL pointer is encountered and returns an error.
In the case the wait for command buffer is possible
(because no lock is held as in the OSN case), still wait
until a channel command buffer is available.
Signed-off-by: Thomas Richter <[email protected]>
Signed-off-by: Ursula Braun <[email protected]>
Reviewed-by: Eugene Crosser <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In the functions that are registering and unregistering MAC
addresses in the qeth-handled hardware, remove callback functions
that are unnesessary, as only the return code is analyzed.
Translate hardware response codes to semi-standard 'errno'-like
codes for readability.
Add kernel-doc description to the internal API function
qeth_send_control_data().
Signed-off-by: Eugene Crosser <[email protected]>
Signed-off-by: Ursula Braun <[email protected]>
Reviewed-by: Thomas-Mich Richter <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
drm_plane_helper_{update,disable} are not specific to primary planes;
fix some copy/paste summaries to avoid confusion.
Cc: [email protected]
Signed-off-by: Matt Roper <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
|
|
When commiting a plane update where the framebuffer doesn't change, we
can skip the prepare_fb/cleanup_fb steps. This also allows us to avoid
an unnecessary vblank wait at the end of the operation when we're just
moving a plane and not changing its image (e.g., for a cursor).
At the moment, i915 is the only upstream driver using the transitional
plane helpers, and thus the only driver affected by this change.
Note that this replicates a corresponding change in the atomic helpers
implemented in
commit ab58e3384b9f9863bfd029b458ff337d381bf6d2
Author: Daniel Vetter <[email protected]>
Date: Mon Nov 24 20:42:42 2014 +0100
drm/atomic-helper: Skip vblank waits for unchanged fbs
Reported-by: Jeremiah Mahler <[email protected]>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88540
Signed-off-by: Matt Roper <[email protected]>
Tested-by: Tested-by: Rodrigo Vivi <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
|