| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Merge misc fixes from Andrew Morton:
"Six fixes"
* emailed patches from Andrew Morton <[email protected]>:
drivers/rtc/rtc-s5m.c: terminate s5m_rtc_id array with empty element
printk: add dummy routine for when CONFIG_PRINTK=n
mm/vmscan: fix highidx argument type
memcg: remove extra newlines from memcg oom kill log
x86, build: replace Perl script with Shell script
mm: page_alloc: embed OOM killing naturally into allocation slowpath
|
|
Commit 69ad0dd7af22b61d9e0e68e56b6290121618b0fb
Author: Ezequiel Garcia <[email protected]>
Date: Mon May 19 13:59:59 2014 -0300
net: mv643xx_eth: Use dma_map_single() to map the skb fragments
caused a nasty regression by removing the support for highmem skb
fragments. By using page_address() to get the address of a fragment's
page, we are assuming a lowmem page. However, such assumption is incorrect,
as fragments can be in highmem pages, resulting in very nasty issues.
This commit fixes this by using the skb_frag_dma_map() helper,
which takes care of mapping the skb fragment properly. Additionally,
the type of mapping is now tracked, so it can be unmapped using
dma_unmap_page or dma_unmap_single when appropriate.
This commit also fixes the error path in txq_init() to release the
resources properly.
Fixes: 69ad0dd7af22 ("net: mv643xx_eth: Use dma_map_single() to map the skb fragments")
Reported-by: Russell King <[email protected]>
Signed-off-by: Ezequiel Garcia <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Ben Hutchings says:
====================
Fixes for sh_eth #2
I'm continuing review and testing of Ethernet support on the R-Car H2
chip. This series fixes more of the issues I've found, but it won't be
the last set.
These are not tested on any of the other supported chips.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
In order to stop the RX path accessing the RX ring while it's being
stopped or resized, we clear the interrupt mask (EESIPR) and then call
free_irq() or synchronise_irq(). This is insufficient because the
interrupt handler or NAPI poller may set EESIPR again after we clear
it. Also, in sh_eth_set_ringparam() we currently don't disable NAPI
polling at all.
I could easily trigger a crash by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine.
To fix this:
- Add a software flag (irq_enabled) to signal whether interrupts
should be enabled
- In the interrupt handler, if the flag is clear then clear EESIPR
and return
- In the NAPI poller, if the flag is clear then don't set EESIPR
- Set the flag before enabling interrupts in sh_eth_dev_init() and
sh_eth_set_ringparam()
- Clear the flag and serialise with the interrupt and NAPI
handlers before clearing EESIPR in sh_eth_close() and
sh_eth_set_ringparam()
After this, I could run the loop for 100,000 iterations successfully.
Signed-off-by: Ben Hutchings <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If the device is down then no packet buffers should be allocated.
We also must not touch its registers as it may be powered off.
Signed-off-by: Ben Hutchings <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.
I could easily trigger this by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
Signed-off-by: Ben Hutchings <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding. This could result in leaking sensitive
data. We also pass different lengths to dma_map_single() and
dma_unmap_single().
Use skb_padto() to pad properly, before calling dma_map_single().
Signed-off-by: Ben Hutchings <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.
Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.
Fixes: d9ba8f9e6298 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <[email protected]> # v3.9+
Reported-by: Felipe Balbi <[email protected]>
Signed-off-by: Mugunthan V N <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
into drm-fixes
Suspend/resume regression fix for 3.19.
* 'drm-fixes-3.19' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Remove rdev->gart.pages_addr array
drm/radeon: Restore GART table contents after pinning it in VRAM v3
drm/radeon: Split off gart_get_page_entry ASIC hook from set_page_entry
|
|
Daniel Borkmann says:
====================
Two cls_bpf fixes
Found them while doing a review on act_bpf and going over the
cls_bpf code again. Will also address the first issue in act_bpf
as it needs to be fixed there, too.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
When creating a bpf classifier in tc with priority collisions and
invoking automatic unique handle assignment, cls_bpf_grab_new_handle()
will return a wrong handle id which in fact is non-unique. Usually
altering of specific filters is being addressed over major id, but
in case of collisions we result in a filter chain, where handle ids
address individual cls_bpf_progs inside the classifier.
Issue is, in cls_bpf_grab_new_handle() we probe for head->hgen handle
in cls_bpf_get() and in case we found a free handle, we're supposed
to use exactly head->hgen. In case of insufficient numbers of handles,
we bail out later as handle id 0 is not allowed.
Fixes: 7d1d65cb84e1 ("net: sched: cls_bpf: add BPF-based classifier")
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In cls_bpf_modify_existing(), we read out the number of filter blocks,
do some sanity checks, allocate a block on that size, and copy over the
BPF instruction blob from user space, then pass everything through the
classic BPF checker prior to installation of the classifier.
We should reject mismatches here, there are 2 scenarios: the number of
filter blocks could be smaller than the provided instruction blob, so
we do a partial copy of the BPF program, and thus the instructions will
either be rejected from the verifier or a valid BPF program will be run;
in the other case, we'll end up copying more than we're supposed to,
and most likely the trailing garbage will be rejected by the verifier
as well (i.e. we need to fit instruction pattern, ret {A,K} needs to be
last instruction, load/stores must be correct, etc); in case not, we
would leak memory when dumping back instruction patterns. The code should
have only used nla_len() as Dave noted to avoid this from the beginning.
Anyway, lets fix it by rejecting such load attempts.
Fixes: 7d1d65cb84e1 ("net: sched: cls_bpf: add BPF-based classifier")
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://people.freedesktop.org/~gabbayo/linux into drm-fixes
A couple of fixes for -rc7 in amdkfd:
- Forgot to free resources when creation of queue has failed
- Initialization of pipelines was incorrect (3 patches)
In addition, The patch "drm/amdkfd: Allow user to limit only queues per device"
is not a fix, but I would like to push it for 3.19 as it changes the ABI
between amdkfd and userspace (by changing the module parameters). I would
prefer *not* to support the two deprecated module parameters if I don't have
too, as amdkfd hasn't been released yet.
* tag 'drm-amdkfd-fixes-2015-01-26' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Fix bug in call to init_pipelines()
drm/amdkfd: Fix bug in pipelines initialization
drm/radeon: Don't increment pipe_id in kgd_init_pipeline
drm/amdkfd: Allow user to limit only queues per device
drm/amdkfd: PQM handle queue creation fault
|
|
Linux 3.19-rc6
pull in rc6 as the amdkfd fixes are based on it, and I'd rather
be doing the merges separately
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-01-21
this is a pull request for v3.19, net/master, which consists of a single patch.
Viktor Babrian fixes the issue in the c_can dirver, that the CAN interface
might continue to send frames after the interface has been shut down.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"The lifetime rules of cgroup hierarchies always have been somewhat
counter-intuitive and cgroup core tried to enforce that hierarchies
w/o userland-visible usages must die in finite amount of time so that
the controllers can be reused for other hierarchies; unfortunately,
this can't be implemented reasonably for the memory controller - the
kmemcg part doesn't have any way to forcefully drain the existing
usages, leading to an interruptible hang if a following mount attempts
to use the controller in any way.
So, it seems like we're stuck with "hierarchies live on till they die
whenever that may be" at least for now. This pretty much confines
attaching controllers to hierarchies to before the hierarchies are
actively used by making dynamic configurations post active usages
unreliable. This has never been reliable and should be fine in
practice given how cgroups are used.
After the patch, hierarchies aren't killed if it isn't already
drained. A following mount attempt of the same mount options will
reuse the existing hierarchy. Mount attempts with differing options
will fail w/ -EBUSY"
* 'for-3.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: prevent mount hang due to memory controller lifetime
|
|
git://ftp.arm.linux.org.uk/~rmk/linux-arm into drm-fixes
3 fixes for the tda998x.
* 'drm-tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: set the CEC I2C address based on the slave I2C address
drm: tda998x: Fix EDID read timeout on HDMI connect
drm: tda998x: Protect the page register
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One correctness fix here for the s2mps11 driver which would have
resulted in some of the regulators being completely broken together
with a fix for locking in regualtor_put() (which is fortunately rarely
called at all in practical systems)"
* tag 'regulator-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mps11: Fix wrong calculation of register offset
regulator: core: fix race condition in regulator_put()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes here, some fixes for issues introduced and
discovered during recent work on the DesignWare driver (which has been
getting a lot of attention recently) and a couple of other drivers.
All serious things for people who run into them"
* tag 'spi-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dw: amend warning message
spi: sh-msiof: fix MDR1_FLD_MASK value
spi: dw-mid: fix FIFO size
spi: dw: Fix detecting FIFO depth
spi/pxa2xx: Clear cur_chip pointer before starting next message
|
|
Array of platform_device_id elements should be terminated with empty
element.
Fixes: 5bccae6ec458 ("rtc: s5m-rtc: add real-time clock driver for s5m8767")
Signed-off-by: Andrey Ryabinin <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
There are missing dummy routines for log_buf_addr_get() and
log_buf_len_get() for when CONFIG_PRINTK is not set causing build
failures.
This patch adds these dummy routines at the appropriate location.
Signed-off-by: Pranith Kumar <[email protected]>
Cc: Michael Ellerman <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Acked-by: Steven Rostedt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
for_each_zone_zonelist_nodemask wants an enum zone_type argument, but is
passed gfp_t:
mm/vmscan.c:2658:9: expected int enum zone_type [signed] highest_zoneidx
mm/vmscan.c:2658:9: got restricted gfp_t [usertype] gfp_mask
mm/vmscan.c:2658:9: warning: incorrect type in argument 2 (different base types)
mm/vmscan.c:2658:9: expected int enum zone_type [signed] highest_zoneidx
mm/vmscan.c:2658:9: got restricted gfp_t [usertype] gfp_mask
convert argument to the correct type.
Signed-off-by: Michael S. Tsirkin <[email protected]>
Cc: Johannes Weiner <[email protected]>
Cc: Vladimir Davydov <[email protected]>
Cc: Rik van Riel <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: Suleiman Souhlal <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Commit e61734c55c24 ("cgroup: remove cgroup->name") added two extra
newlines to memcg oom kill log messages. This makes dmesg hard to read
and parse. The issue affects 3.15+.
Example:
Task in /t <<< extra #1
killed as a result of limit of /t
<<< extra #2
memory: usage 102400kB, limit 102400kB, failcnt 274712
Remove the extra newlines from memcg oom kill messages, so the messages
look like:
Task in /t killed as a result of limit of /t
memory: usage 102400kB, limit 102400kB, failcnt 240649
Fixes: e61734c55c24 ("cgroup: remove cgroup->name")
Signed-off-by: Greg Thelen <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Acked-by: Johannes Weiner <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Commit e6023367d779 ("x86, kaslr: Prevent .bss from overlaping initrd")
added Perl to the required build environment. This reimplements in
shell the Perl script used to find the size of the kernel with bss and
brk added.
Signed-off-by: Kees Cook <[email protected]>
Reported-by: Rob Landley <[email protected]>
Acked-by: Rob Landley <[email protected]>
Cc: Anca Emanuel <[email protected]>
Cc: Fengguang Wu <[email protected]>
Cc: Junjie Mao <[email protected]>
Cc: Kees Cook <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The OOM killing invocation does a lot of duplicative checks against the
task's allocation context. Rework it to take advantage of the existing
checks in the allocator slowpath.
The OOM killer is invoked when the allocator is unable to reclaim any
pages but the allocation has to keep looping. Instead of having a check
for __GFP_NORETRY hidden in oom_gfp_allowed(), just move the OOM
invocation to the true branch of should_alloc_retry(). The __GFP_FS
check from oom_gfp_allowed() can then be moved into the OOM avoidance
branch in __alloc_pages_may_oom(), along with the PF_DUMPCORE test.
__alloc_pages_may_oom() can then signal to the caller whether the OOM
killer was invoked, instead of requiring it to duplicate the order and
high_zoneidx checks to guess this when deciding whether to continue.
Signed-off-by: Johannes Weiner <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Cc: David Rientjes <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Make the slave support depend on CONFIG_I2C_SLAVE. Otherwise it gets
included unconditionally, even when it is not needed.
I2C bus drivers which implement slave support must select
I2C_SLAVE.
Signed-off-by: Jean Delvare <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
|
|
Add helpers for the following kernel formats:
%pi4 print an IPv4 address with leading zeros
%pI4 print an IPv4 address without leading zeros
%pi6 print an IPv6 address without colons
%pI6 print an IPv6 address with colons
%pI6c print an IPv6 address in compressed form with colons
%pISpc print an IP address from a sockaddr
Allows these formats to be used in tracepoints.
Quite a bit of this is adapted from code in lib/vsprintf.c.
v4:
- fixed pI6c description in git commit message per Valdis' comment
v3:
- use of 'c' and 'p' requires 'I'
v2:
- pass ptr+1 to print_ip_arg per Namhyung's comments
- added field length checks to sockaddr function
Signed-off-by: David Ahern <[email protected]>
Acked-by: Steven Rostedt <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
When the last subscriber to a "Through" port has been removed, the
subscribed destination ports might still be active, so it would be
wrong to send "all sounds off" and "reset controller" events to them.
The proper place for such a shutdown would be the closing of the actual
MIDI port (and close_substream() in rawmidi.c already can do this).
This also fixes a deadlock when dummy_unuse() tries to send events to
its own port that is already locked because it is being freed.
Reported-by: Peter Billam <[email protected]>
Cc: <[email protected]>
Signed-off-by: Clemens Ladisch <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Commit 315786ebbf4a ("iommu: Add iommu_map_sg() function") adds a new
->map_sg() callback and provides a default implementation that drivers
can use until they implement a hardware-specific variant. Unfortunately
the Tegra GART driver was not updated as part of that commit, so that
iommu_map_sg() calls on a domain provided by the GART cause an oops.
Fixes: 315786ebbf4a ("iommu: Add iommu_map_sg() function")
Cc: Hiroshi Doyu <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
|
|
The driver currently doesn't work as expected and causes existing setups
with Tegra20 to break after commit df06b759f2cf ("drm/tegra: Add IOMMU
support"). To restore these setups, do not register the operations with
the platform bus for now. Fixing this properly will involve non-trivial
changes to the DRM driver, which are unlikely to be accepted at this
point in the release cycle.
Reported-by: Misha Komarovskiy <[email protected]>
Reported-by: Nicolas Chauvet <[email protected]>
Tested-by: Misha Komarovskiy <[email protected]>
Tested-by: Dmitry Osipenko <[email protected]>
Cc: Hiroshi Doyu <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.19
There's a lot more fixes here than I'd like since I've been lax in
sending things throughout the release cycle but there's only two in
generic code and they've had quite some time to cook in -next so
hopefully on balance are OK.
The two generic fixes are a fix for crashes on capture DAIs in the
compress code and a fix for error handling on probe failures which would
have been harmless in the past but now oopses with the new dynamic probe
code.
|
|
'asoc/fix/ts3a227e', 'asoc/fix/wm8904' and 'asoc/fix/wm8960' into asoc-linus
|
|
'asoc/fix/fsl-ssi', 'asoc/fix/imx', 'asoc/fix/intel', 'asoc/fix/omap', 'asoc/fix/rockchip' and 'asoc/fix/rt286' into asoc-linus
|
|
|
|
|
|
'spi/fix/pxa2xx' into spi-linus
|
|
BDW with PCI-IDs ended in "2" aren't ULT, but HALO.
Let's fix it and at least allow VGA to work on this units.
v2: forgot ammend and v1 doesn't compile
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87220
Cc: Xion Zhang <[email protected]>
Cc: Guo Jinxian <[email protected]>
Cc: Jani Nikula <[email protected]>
Cc: Stable <[email protected]>
Signed-off-by: Rodrigo Vivi <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
|
|
It seems in the past we have BDW with PCH not been propperly identified
and we force it to be LPT and we were warning !IS_HASWELL on propper identification.
Now that products are out there we are receiveing logs with this incorrect WARN.
And also according to local tests on all production BDW here ULT or HALO we don't
need this force anymore. So let's clean this block for real.
v2: Fix LPT_LP WARNs to avoid wrong warns on BDW_ULT (By Jani).
Reference: https://bugs.freedesktop.org/attachment.cgi?id=110972
Cc: Jani Nikula <[email protected]>
Cc: Paulo Zanoni <[email protected]>
Cc: Xion Zhang <[email protected]>
Cc: [email protected]
Signed-off-by: Rodrigo Vivi <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
|
|
When creating a fence for a tiled object, only fence the area that
makes up the actual tiles. The object may be larger than the tiled
area and if we allow those extra addresses to be fenced, they'll
get converted to addresses beyond where the object is mapped. This
opens up the possiblity of writes beyond the end of object.
To prevent this, we adjust the size of the fence to only encompass
the area that makes up the actual tiles. The extra space is considered
un-tiled and now behaves as if it was a linear object.
Testcase: igt/gem_tiled_fence_overflow
Reported-by: Dan Hettena <[email protected]>
Signed-off-by: Bob Paauwe <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Cc: [email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
commit 6dda730e55f412a6dfb181cae6784822ba463847
Author: Jani Nikula <[email protected]>
Date: Tue Jun 24 18:27:40 2014 +0300
drm/i915: respect the VBT minimum backlight brightness
introduced a bug which resulted in inconsistent brightness levels on
different machines. If a suspended was entered with the screen off some
machines would resume with the screen at minimum brightness and others
at maximum brightness.
The following commands can be used to produce this behavior.
xset dpms force off
sleep 1
sudo systemctl suspend
(resume ...)
The root cause of this problem is a comparison which checks to see if
the backlight level is zero when the panel is enabled. If it is zero,
it is set to the maximum level. Unfortunately, not all machines have a
minimum level of zero. On those machines the level is left at the
minimum instead of begin set to the maximum.
Fix the bug by updating the comparison to check for the minimum
backlight level instead of zero. Also, expand the comparison for
the possible case when the level is less than the minimum.
Fixes: 6dda730e55f4 ("respect the VBT minimum backlight brightness")
Signed-off-by: Jeremiah Mahler <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
|
|
Commit 82460d972 ("drm/i915: Rework ppgtt init to no require an aliasing
ppgtt") introduced a regression on Broadwell, triggering the following
IOMMU fault at startup:
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
dmar: DRHD: handling fault status reg 2
dmar: DMAR:[DMA Write] Request device [00:02.0] fault addr 880000
DMAR:[fault reason 23] Unknown
fbcon: inteldrmfb (fb0) is primary device
Further commentary from Daniel:
I sugggested this change to David after staring at the offending patch
for a while. I have no idea and theory whatsoever why this would upset
the gpu less than the other way round. But it seems to work. David
promised to chase hw people a bit more to get a more meaningful answer.
Wrt the comment that this deletes: I've done some digging and afaict
loading context before ppgtt enable was once required before our recent
restructuring of the context/ppgtt init code: Before that context sw
setup (i.e. allocating the default context) and hw setup was smashed
together. Also the setup of the default context was the bit that
actually allocated the aliasing ppgtt structures. Which is the reason
for the context before ppgtt depency.
Or was, since with all the untangling there's no no real depency any
more (functional, who knows what the hw is doing), so the comment is
just stale.
Signed-off-by: David Woodhouse <[email protected]>
Cc: [email protected]
Reviewed-by: Daniel Vetter <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
|
|
Today we expect that all the bank are enabled, and count the number of banks
used by the pinctrl based on it instead of using the last bank id enabled.
So switch to it, set the chained IRQ at runtime based on enabled banks
and wait only the number of enabled gpio controllers at probe time.
Cc: <[email protected]> # 3.18
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Signed-off-by: Ludovic Desroches <[email protected]>
Acked-by: Nicolas Ferre <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Ursula Braun says:
====================
s390/qeth patches for net
here are two s390/qeth patches built for net.
One patch is quite large, but we would like to fix the locking warning
seen in recent kernels as soon as possible. But if you want me to submit
these patches for net-next, I will do.
Or Gerlitz says:
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Do not wait for channel command buffers in IPA commands.
The potential wait could be done while holding a spin lock and causes
in recent kernels such a bug if kernel lock debugging is enabled:
kernel: BUG: sleeping function called from invalid context at drivers/s390/net/qeth_core_main.c:
794
kernel: in_atomic(): 1, irqs_disabled(): 0, pid: 2031, name: NetworkManager
kernel: 2 locks held by NetworkManager/2031:
kernel: #0: (rtnl_mutex){+.+.+.}, at: [<00000000006e0d7a>] rtnetlink_rcv+0x32/0x50
kernel: #1: (_xmit_ETHER){+.....}, at: [<00000000006cfe90>] dev_set_rx_mode+0x30/0x50
kernel: CPU: 0 PID: 2031 Comm: NetworkManager Not tainted 3.18.0-rc5-next-20141124 #1
kernel: 00000000275fb1f0 00000000275fb280 0000000000000002 0000000000000000
00000000275fb320 00000000275fb298 00000000275fb298 00000000007e326a
0000000000000000 000000000099ce2c 00000000009b4988 000000000000000b
00000000275fb2e0 00000000275fb280 0000000000000000 0000000000000000
0000000000000000 00000000001129c8 00000000275fb280 00000000275fb2e0
kernel: Call Trace:
kernel: ([<00000000001128b0>] show_trace+0xf8/0x158)
kernel: [<000000000011297a>] show_stack+0x6a/0xe8
kernel: [<00000000007e995a>] dump_stack+0x82/0xb0
kernel: [<000000000017d668>] ___might_sleep+0x170/0x228
kernel: [<000003ff80026f0e>] qeth_wait_for_buffer+0x36/0xd0 [qeth]
kernel: [<000003ff80026fe2>] qeth_get_ipacmd_buffer+0x3a/0xc0 [qeth]
kernel: [<000003ff80105078>] qeth_l3_send_setdelmc+0x58/0xf8 [qeth_l3]
kernel: [<000003ff8010b1fe>] qeth_l3_set_ip_addr_list+0x2c6/0x848 [qeth_l3]
kernel: [<000003ff8010bbb4>] qeth_l3_set_multicast_list+0x434/0xc48 [qeth_l3]
kernel: [<00000000006cfe9a>] dev_set_rx_mode+0x3a/0x50
kernel: [<00000000006cff90>] __dev_open+0xe0/0x140
kernel: [<00000000006d02a0>] __dev_change_flags+0xa0/0x178
kernel: [<00000000006d03a8>] dev_change_flags+0x30/0x70
kernel: [<00000000006e14ee>] do_setlink+0x346/0x9a0
...
The device driver has plenty of command buffers available
per channel for channel command communication.
In the extremely rare case when there is no command buffer
available, return a NULL pointer and issue a warning
in the kernel log. The caller handles the case when
a NULL pointer is encountered and returns an error.
In the case the wait for command buffer is possible
(because no lock is held as in the OSN case), still wait
until a channel command buffer is available.
Signed-off-by: Thomas Richter <[email protected]>
Signed-off-by: Ursula Braun <[email protected]>
Reviewed-by: Eugene Crosser <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In the functions that are registering and unregistering MAC
addresses in the qeth-handled hardware, remove callback functions
that are unnesessary, as only the return code is analyzed.
Translate hardware response codes to semi-standard 'errno'-like
codes for readability.
Add kernel-doc description to the internal API function
qeth_send_control_data().
Signed-off-by: Eugene Crosser <[email protected]>
Signed-off-by: Ursula Braun <[email protected]>
Reviewed-by: Thomas-Mich Richter <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In my last commit (a3c00e4: ipv6: Remove BACKTRACK macro), the changes in
__ip6_route_redirect is incorrect. The following case is missed:
1. The for loop tries to find a valid gateway rt. If it fails to find
one, rt will be NULL.
2. When rt is NULL, it is set to the ip6_null_entry.
3. The newly added 'else if', from a3c00e4, will stop the backtrack from
happening.
Signed-off-by: Martin KaFai Lau <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Hopefully the last round of fixes for 3.19
- regression fix for the LDT changes
- regression fix for XEN interrupt handling caused by the APIC
changes
- regression fixes for the PAT changes
- last minute fixes for new the MPX support
- regression fix for 32bit UP
- fix for a long standing relocation issue on 64bit tagged for stable
- functional fix for the Hyper-V clocksource tagged for stable
- downgrade of a pr_err which tends to confuse users
Looks a bit on the large side, but almost half of it are valuable
comments"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Change Fast TSC calibration failed from error to info
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
x86, mm: Change cachemode exports to non-gpl
x86, tls: Interpret an all-zero struct user_desc as "no segment"
x86, tls, ldt: Stop checking lm in LDT_empty
x86, mpx: Strictly enforce empty prctl() args
x86, mpx: Fix potential performance issue on unmaps
x86, mpx: Explicitly disable 32-bit MPX support on 64-bit kernels
x86, hyperv: Mark the Hyper-V clocksource as being continuous
x86: Don't rely on VMWare emulating PAT MSR correctly
x86, irq: Properly tag virtualization entry in /proc/interrupts
x86, boot: Skip relocs when load address unchanged
x86/xen: Override ACPI IRQ management callback __acpi_unregister_gsi
ACPI: pci: Do not clear pci_dev->irq in acpi_pci_irq_disable()
x86/xen: Treat SCI interrupt as normal GSI interrupt
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"From the irqchip departement you get:
- regression fix for omap-intc
- regression fix for atmel-aic-common
- functional correctness fix for hip04
- type mismatch fix for gic-v3-its
- proper error pointer check for mtd-sysirq
Mostly one and two liners except for the omap regression fix which is
slightly larger than desired"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: atmel-aic-common: Prevent clobbering of priority when changing IRQ type
irqchip: omap-intc: Fix legacy DMA regression
irqchip: gic-v3-its: Fix use of max with decimal constant
irqchip: hip04: Initialize hip04_cpu_map to 0xffff
irqchip: mtk-sysirq: Use IS_ERR() instead of NULL pointer check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A set of small fixes:
- regression fix for exynos_mct clocksource
- trivial build fix for kona clocksource
- functional one liner fix for the sh_tmu clocksource
- two validation fixes to prevent (root only) data corruption in the
kernel via settimeofday and adjtimex. Tagged for stable"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: adjtimex: Validate the ADJ_FREQUENCY values
time: settimeofday: Validate the values of tv from user
clocksource: sh_tmu: Set cpu_possible_mask to fix SMP broadcast
clocksource: kona: fix __iomem annotation
clocksource: exynos_mct: Fix bitmask regression for exynos4_mct_write
|