aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2021-01-26wext: fix NULL-ptr-dereference with cfg80211's lack of commit()Johannes Berg1-2/+3
Since cfg80211 doesn't implement commit, we never really cared about that code there (and it's configured out w/o CONFIG_WIRELESS_EXT). After all, since it has no commit, it shouldn't return -EIWCOMMIT to indicate commit is needed. However, EIWCOMMIT is actually an alias for EINPROGRESS, which _can_ happen if e.g. we try to change the frequency but we're already in the process of connecting to some network, and drivers could return that value (or even cfg80211 itself might). This then causes us to crash because dev->wireless_handlers is NULL but we try to check dev->wireless_handlers->standard[0]. Fix this by also checking dev->wireless_handlers. Also simplify the code a little bit. Cc: [email protected] Reported-by: [email protected] Reported-by: [email protected] Link: https://lore.kernel.org/r/20210121171621.2076e4a37d5a.I5d9c72220fe7bb133fb718751da0180a57ecba4e@changeid Signed-off-by: Johannes Berg <[email protected]>
2021-01-26HID: wacom: Correct NULL dereference on AES pen proximityJason Gerecke2-4/+5
The recent commit to fix a memory leak introduced an inadvertant NULL pointer dereference. The `wacom_wac->pen_fifo` variable was never intialized, resuling in a crash whenever functions tried to use it. Since the FIFO is only used by AES pens (to buffer events from pen proximity until the hardware reports the pen serial number) this would have been easily overlooked without testing an AES device. This patch converts `wacom_wac->pen_fifo` over to a pointer (since the call to `devres_alloc` allocates memory for us) and ensures that we assign it to point to the allocated and initalized `pen_fifo` before the function returns. Link: https://github.com/linuxwacom/input-wacom/issues/230 Fixes: 37309f47e2f5 ("HID: wacom: Fix memory leakage caused by kfifo_alloc") CC: [email protected] # v4.19+ Signed-off-by: Jason Gerecke <[email protected]> Tested-by: Ping Cheng <[email protected]> Signed-off-by: Jiri Kosina <[email protected]>
2021-01-26xen-blkfront: allow discard-* nodes to be optionalRoger Pau Monne1-13/+7
This is inline with the specification described in blkif.h: * discard-granularity: should be set to the physical block size if node is not present. * discard-alignment, discard-secure: should be set to 0 if node not present. This was detected as QEMU would only create the discard-granularity node but not discard-alignment, and thus the setup done in blkfront_setup_discard would fail. Fix blkfront_setup_discard to not fail on missing nodes, and also fix blkif_set_queue_limits to set the discard granularity to the physical block size if none is specified in xenbus. Fixes: ed30bf317c5ce ('xen-blkfront: Handle discard requests.') Reported-by: Arthur Borsboom <[email protected]> Signed-off-by: Roger Pau Monné <[email protected]> Reviewed-by: Juergen Gross <[email protected]> Tested-By: Arthur Borsboom <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Juergen Gross <[email protected]>
2021-01-26ecryptfs: fix uid translation for setxattr on security.capabilityMiklos Szeredi1-3/+7
Prior to commit 7c03e2cda4a5 ("vfs: move cap_convert_nscap() call into vfs_setxattr()") the translation of nscap->rootid did not take stacked filesystems (overlayfs and ecryptfs) into account. That patch fixed the overlay case, but made the ecryptfs case worse. Restore old the behavior for ecryptfs that existed before the overlayfs fix. This does not fix ecryptfs's handling of complex user namespace setups, but it does make sure existing setups don't regress. Reported-by: Eric W. Biederman <[email protected]> Cc: Tyler Hicks <[email protected]> Fixes: 7c03e2cda4a5 ("vfs: move cap_convert_nscap() call into vfs_setxattr()") Signed-off-by: Miklos Szeredi <[email protected]> Signed-off-by: Tyler Hicks <[email protected]>
2021-01-25KVM: x86: allow KVM_REQ_GET_NESTED_STATE_PAGES outside guest mode for VMXPaolo Bonzini3-9/+29
VMX also uses KVM_REQ_GET_NESTED_STATE_PAGES for the Hyper-V eVMCS, which may need to be loaded outside guest mode. Therefore we cannot WARN in that case. However, that part of nested_get_vmcs12_pages is _not_ needed at vmentry time. Split it out of KVM_REQ_GET_NESTED_STATE_PAGES handling, so that both vmentry and migration (and in the latter case, independent of is_guest_mode) do the parts that are needed. Cc: <[email protected]> # 5.10.x: f2c7ef3ba: KVM: nSVM: cancel KVM_REQ_GET_NESTED_STATE_PAGES Cc: <[email protected]> # 5.10.x Signed-off-by: Paolo Bonzini <[email protected]>
2021-01-25KVM: x86: Revert "KVM: x86: Mark GPRs dirty when written"Sean Christopherson1-26/+25
Revert the dirty/available tracking of GPRs now that KVM copies the GPRs to the GHCB on any post-VMGEXIT VMRUN, even if a GPR is not dirty. Per commit de3cd117ed2f ("KVM: x86: Omit caching logic for always-available GPRs"), tracking for GPRs noticeably impacts KVM's code footprint. This reverts commit 1c04d8c986567c27c56c05205dceadc92efb14ff. Signed-off-by: Sean Christopherson <[email protected]> Message-Id: <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2021-01-25KVM: SVM: Unconditionally sync GPRs to GHCB on VMRUN of SEV-ES guestSean Christopherson1-9/+6
Drop the per-GPR dirty checks when synchronizing GPRs to the GHCB, the GRPs' dirty bits are set from time zero and never cleared, i.e. will always be seen as dirty. The obvious alternative would be to clear the dirty bits when appropriate, but removing the dirty checks is desirable as it allows reverting GPR dirty+available tracking, which adds overhead to all flavors of x86 VMs. Note, unconditionally writing the GPRs in the GHCB is tacitly allowed by the GHCB spec, which allows the hypervisor (or guest) to provide unnecessary info; it's the guest's responsibility to consume only what it needs (the hypervisor is untrusted after all). The guest and hypervisor can supply additional state if desired but must not rely on that additional state being provided. Cc: Brijesh Singh <[email protected]> Cc: Tom Lendacky <[email protected]> Fixes: 291bd20d5d88 ("KVM: SVM: Add initial support for a VMGEXIT VMEXIT") Signed-off-by: Sean Christopherson <[email protected]> Message-Id: <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2021-01-25KVM: nVMX: Sync unsync'd vmcs02 state to vmcs12 on migrationMaxim Levitsky1-5/+8
Even when we are outside the nested guest, some vmcs02 fields may not be in sync vs vmcs12. This is intentional, even across nested VM-exit, because the sync can be delayed until the nested hypervisor performs a VMCLEAR or a VMREAD/VMWRITE that affects those rarely accessed fields. However, during KVM_GET_NESTED_STATE, the vmcs12 has to be up to date to be able to restore it. To fix that, call copy_vmcs02_to_vmcs12_rare() before the vmcs12 contents are copied to userspace. Fixes: 7952d769c29ca ("KVM: nVMX: Sync rarely accessed guest fields only when needed") Reviewed-by: Sean Christopherson <[email protected]> Signed-off-by: Maxim Levitsky <[email protected]> Message-Id: <[email protected]> Cc: [email protected] Signed-off-by: Paolo Bonzini <[email protected]>
2021-01-25kvm: tracing: Fix unmatched kvm_entry and kvm_exit eventsLorenzo Brescia3-2/+5
On VMX, if we exit and then re-enter immediately without leaving the vmx_vcpu_run() function, the kvm_entry event is not logged. That means we will see one (or more) kvm_exit, without its (their) corresponding kvm_entry, as shown here: CPU-1979 [002] 89.871187: kvm_entry: vcpu 1 CPU-1979 [002] 89.871218: kvm_exit: reason MSR_WRITE CPU-1979 [002] 89.871259: kvm_exit: reason MSR_WRITE It also seems possible for a kvm_entry event to be logged, but then we leave vmx_vcpu_run() right away (if vmx->emulation_required is true). In this case, we will have a spurious kvm_entry event in the trace. Fix these situations by moving trace_kvm_entry() inside vmx_vcpu_run() (where trace_kvm_exit() already is). A trace obtained with this patch applied looks like this: CPU-14295 [000] 8388.395387: kvm_entry: vcpu 0 CPU-14295 [000] 8388.395392: kvm_exit: reason MSR_WRITE CPU-14295 [000] 8388.395393: kvm_entry: vcpu 0 CPU-14295 [000] 8388.395503: kvm_exit: reason EXTERNAL_INTERRUPT Of course, not calling trace_kvm_entry() in common x86 code any longer means that we need to adjust the SVM side of things too. Signed-off-by: Lorenzo Brescia <[email protected]> Signed-off-by: Dario Faggioli <[email protected]> Message-Id: <160873470698.11652.13483635328769030605.stgit@Wayrath> Signed-off-by: Paolo Bonzini <[email protected]>
2021-01-25KVM: Documentation: Update description of KVM_{GET,CLEAR}_DIRTY_LOGZenghui Yu1-9/+7
Update various words, including the wrong parameter name and the vague description of the usage of "slot" field. Signed-off-by: Zenghui Yu <[email protected]> Message-Id: <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2021-01-25KVM: x86: get smi pending status correctlyJay Zhou1-0/+4
The injection process of smi has two steps: Qemu KVM Step1: cpu->interrupt_request &= \ ~CPU_INTERRUPT_SMI; kvm_vcpu_ioctl(cpu, KVM_SMI) call kvm_vcpu_ioctl_smi() and kvm_make_request(KVM_REQ_SMI, vcpu); Step2: kvm_vcpu_ioctl(cpu, KVM_RUN, 0) call process_smi() if kvm_check_request(KVM_REQ_SMI, vcpu) is true, mark vcpu->arch.smi_pending = true; The vcpu->arch.smi_pending will be set true in step2, unfortunately if vcpu paused between step1 and step2, the kvm_run->immediate_exit will be set and vcpu has to exit to Qemu immediately during step2 before mark vcpu->arch.smi_pending true. During VM migration, Qemu will get the smi pending status from KVM using KVM_GET_VCPU_EVENTS ioctl at the downtime, then the smi pending status will be lost. Signed-off-by: Jay Zhou <[email protected]> Signed-off-by: Shengen Zhuang <[email protected]> Message-Id: <[email protected]> Cc: [email protected] Signed-off-by: Paolo Bonzini <[email protected]>
2021-01-25KVM: x86/pmu: Fix HW_REF_CPU_CYCLES event pseudo-encoding in intel_arch_events[]Like Xu1-1/+1
The HW_REF_CPU_CYCLES event on the fixed counter 2 is pseudo-encoded as 0x0300 in the intel_perfmon_event_map[]. Correct its usage. Fixes: 62079d8a4312 ("KVM: PMU: add proper support for fixed counter 2") Signed-off-by: Like Xu <[email protected]> Message-Id: <[email protected]> Reviewed-by: Sean Christopherson <[email protected]> Cc: [email protected] Signed-off-by: Paolo Bonzini <[email protected]>
2021-01-25KVM: x86/pmu: Fix UBSAN shift-out-of-bounds warning in intel_pmu_refresh()Like Xu1-0/+4
Since we know vPMU will not work properly when (1) the guest bit_width(s) of the [gp|fixed] counters are greater than the host ones, or (2) guest requested architectural events exceeds the range supported by the host, so we can setup a smaller left shift value and refresh the guest cpuid entry, thus fixing the following UBSAN shift-out-of-bounds warning: shift exponent 197 is too large for 64-bit type 'long long unsigned int' Call Trace: __dump_stack lib/dump_stack.c:79 [inline] dump_stack+0x107/0x163 lib/dump_stack.c:120 ubsan_epilogue+0xb/0x5a lib/ubsan.c:148 __ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:395 intel_pmu_refresh.cold+0x75/0x99 arch/x86/kvm/vmx/pmu_intel.c:348 kvm_vcpu_after_set_cpuid+0x65a/0xf80 arch/x86/kvm/cpuid.c:177 kvm_vcpu_ioctl_set_cpuid2+0x160/0x440 arch/x86/kvm/cpuid.c:308 kvm_arch_vcpu_ioctl+0x11b6/0x2d70 arch/x86/kvm/x86.c:4709 kvm_vcpu_ioctl+0x7b9/0xdb0 arch/x86/kvm/../../../virt/kvm/kvm_main.c:3386 vfs_ioctl fs/ioctl.c:48 [inline] __do_sys_ioctl fs/ioctl.c:753 [inline] __se_sys_ioctl fs/ioctl.c:739 [inline] __x64_sys_ioctl+0x193/0x200 fs/ioctl.c:739 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reported-by: [email protected] Signed-off-by: Like Xu <[email protected]> Message-Id: <[email protected]> Cc: [email protected] Signed-off-by: Paolo Bonzini <[email protected]>
2021-01-25KVM: x86: Add more protection against undefined behavior in rsvd_bits()Sean Christopherson1-1/+8
Add compile-time asserts in rsvd_bits() to guard against KVM passing in garbage hardcoded values, and cap the upper bound at '63' for dynamic values to prevent generating a mask that would overflow a u64. Suggested-by: Paolo Bonzini <[email protected]> Signed-off-by: Sean Christopherson <[email protected]> Message-Id: <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2021-01-25KVM: Documentation: Fix spec for KVM_CAP_ENABLE_CAP_VMQuentin Perret1-1/+1
The documentation classifies KVM_ENABLE_CAP with KVM_CAP_ENABLE_CAP_VM as a vcpu ioctl, which is incorrect. Fix it by specifying it as a VM ioctl. Fixes: e5d83c74a580 ("kvm: make KVM_CAP_ENABLE_CAP_VM architecture agnostic") Signed-off-by: Quentin Perret <[email protected]> Message-Id: <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2021-01-25Merge tag 'kvmarm-fixes-5.11-2' of ↵Paolo Bonzini6-49/+74
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD KVM/arm64 fixes for 5.11, take #2 - Don't allow tagged pointers to point to memslots - Filter out ARMv8.1+ PMU events on v8.0 hardware - Hide PMU registers from userspace when no PMU is configured - More PMU cleanups - Don't try to handle broken PSCI firmware - More sys_reg() to reg_to_encoding() conversions
2021-01-25Merge branch 'linus' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 Pull crypto fix from Herbert Xu: "Fix a regression in the cesa driver" * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: marvel/cesa - Fix tdma descriptor on 64-bit
2021-01-25uapi: fix big endian definition of ipv6_rpl_sr_hdrJustin Iurman1-3/+3
Following RFC 6554 [1], the current order of fields is wrong for big endian definition. Indeed, here is how the header looks like: +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Next Header | Hdr Ext Len | Routing Type | Segments Left | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | CmprI | CmprE | Pad | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ This patch reorders fields so that big endian definition is now correct. [1] https://tools.ietf.org/html/rfc6554#section-3 Fixes: cfa933d938d8 ("include: uapi: linux: add rpl sr header definition") Signed-off-by: Justin Iurman <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-01-25dt-bindings: usb: j721e: add ranges and dma-coherent propsGrygorii Strashko1-0/+4
Add missed 'ranges' and 'dma-coherent' properties as cdns-usb DT nodes has child node and DMA IO is coherent on TI K3 J721E/J7200 SoCs. This also fixes dtbs_check warning: cdns-usb@4104000: 'dma-coherent', 'ranges' do not match any of the regexes: '^usb@', 'pinctrl-[0-9]+' Signed-off-by: Grygorii Strashko <[email protected]> Acked-by: Aswath Govindraju <[email protected]> Reviewed-by: Aswath Govindraju <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Rob Herring <[email protected]>
2021-01-25SUNRPC: Handle 0 length opaque XDR object data properlyDave Wysochanski1-3/+6
When handling an auth_gss downcall, it's possible to get 0-length opaque object for the acceptor. In the case of a 0-length XDR object, make sure simple_get_netobj() fills in dest->data = NULL, and does not continue to kmemdup() which will set dest->data = ZERO_SIZE_PTR for the acceptor. The trace event code can handle NULL but not ZERO_SIZE_PTR for a string, and so without this patch the rpcgss_context trace event will crash the kernel as follows: [ 162.887992] BUG: kernel NULL pointer dereference, address: 0000000000000010 [ 162.898693] #PF: supervisor read access in kernel mode [ 162.900830] #PF: error_code(0x0000) - not-present page [ 162.902940] PGD 0 P4D 0 [ 162.904027] Oops: 0000 [#1] SMP PTI [ 162.905493] CPU: 4 PID: 4321 Comm: rpc.gssd Kdump: loaded Not tainted 5.10.0 #133 [ 162.908548] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 [ 162.910978] RIP: 0010:strlen+0x0/0x20 [ 162.912505] Code: 48 89 f9 74 09 48 83 c1 01 80 39 00 75 f7 31 d2 44 0f b6 04 16 44 88 04 11 48 83 c2 01 45 84 c0 75 ee c3 0f 1f 80 00 00 00 00 <80> 3f 00 74 10 48 89 f8 48 83 c0 01 80 38 00 75 f7 48 29 f8 c3 31 [ 162.920101] RSP: 0018:ffffaec900c77d90 EFLAGS: 00010202 [ 162.922263] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 00000000fffde697 [ 162.925158] RDX: 000000000000002f RSI: 0000000000000080 RDI: 0000000000000010 [ 162.928073] RBP: 0000000000000010 R08: 0000000000000e10 R09: 0000000000000000 [ 162.930976] R10: ffff8e698a590cb8 R11: 0000000000000001 R12: 0000000000000e10 [ 162.933883] R13: 00000000fffde697 R14: 000000010034d517 R15: 0000000000070028 [ 162.936777] FS: 00007f1e1eb93700(0000) GS:ffff8e6ab7d00000(0000) knlGS:0000000000000000 [ 162.940067] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 162.942417] CR2: 0000000000000010 CR3: 0000000104eba000 CR4: 00000000000406e0 [ 162.945300] Call Trace: [ 162.946428] trace_event_raw_event_rpcgss_context+0x84/0x140 [auth_rpcgss] [ 162.949308] ? __kmalloc_track_caller+0x35/0x5a0 [ 162.951224] ? gss_pipe_downcall+0x3a3/0x6a0 [auth_rpcgss] [ 162.953484] gss_pipe_downcall+0x585/0x6a0 [auth_rpcgss] [ 162.955953] rpc_pipe_write+0x58/0x70 [sunrpc] [ 162.957849] vfs_write+0xcb/0x2c0 [ 162.959264] ksys_write+0x68/0xe0 [ 162.960706] do_syscall_64+0x33/0x40 [ 162.962238] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 162.964346] RIP: 0033:0x7f1e1f1e57df Signed-off-by: Dave Wysochanski <[email protected]> Signed-off-by: Trond Myklebust <[email protected]>
2021-01-25SUNRPC: Move simple_get_bytes and simple_get_netobj into private headerDave Wysochanski4-60/+46
Remove duplicated helper functions to parse opaque XDR objects and place inside new file net/sunrpc/auth_gss/auth_gss_internal.h. In the new file carry the license and copyright from the source file net/sunrpc/auth_gss/auth_gss.c. Finally, update the comment inside include/linux/sunrpc/xdr.h since lockd is not the only user of struct xdr_netobj. Signed-off-by: Dave Wysochanski <[email protected]> Signed-off-by: Trond Myklebust <[email protected]>
2021-01-25fs/pipe: allow sendfile() to pipe againJohannes Berg1-0/+1
After commit 36e2c7421f02 ("fs: don't allow splice read/write without explicit ops") sendfile() could no longer send data from a real file to a pipe, breaking for example certain cgit setups (e.g. when running behind fcgiwrap), because in this case cgit will try to do exactly this: sendfile() to a pipe. Fix this by using iter_file_splice_write for the splice_write method of pipes, as suggested by Christoph. Cc: [email protected] Fixes: 36e2c7421f02 ("fs: don't allow splice read/write without explicit ops") Suggested-by: Christoph Hellwig <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Tested-by: Johannes Berg <[email protected]> Signed-off-by: Johannes Berg <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2021-01-25Commit 9bb48c82aced ("tty: implement write_iter") converted the ttySami Tolvanen3-7/+3
layer to use write_iter. Fix the redirected_tty_write declaration also in n_tty and change the comparisons to use write_iter instead of write. [ Also moved the declaration of redirected_tty_write() to the proper location in a header file. The reason for the bug was the bogus extern declaration in n_tty.c silently not matching the changed definition in tty_io.c, and because it wasn't in a shared header file, there was no cross-checking of the declaration. Sami noticed because Clang's Control Flow Integrity checking ended up incidentally noticing the inconsistent declaration. - Linus ] Fixes: 9bb48c82aced ("tty: implement write_iter") Signed-off-by: Sami Tolvanen <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2021-01-25dt-bindings:iio:adc: update adc.yaml referenceMauro Carvalho Chehab1-1/+1
Changeset b70d154d6558 ("dt-bindings:iio:adc: convert adc.txt to yaml") renamed: Documentation/devicetree/bindings/iio/adc/adc.txt to: Documentation/devicetree/bindings/iio/adc/adc.yaml. Update its cross-reference accordingly. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Acked-by: Jonathan Cameron <[email protected]> Link: https://lore.kernel.org/r/8e37dba8ae9099acd649bab8a1cf718caa4f3e6a.1610535350.git.mchehab+huawei@kernel.org Signed-off-by: Rob Herring <[email protected]>
2021-01-25dt-bindings: memory: mediatek: update mediatek,smi-larb.yaml referencesMauro Carvalho Chehab4-4/+4
Changeset 27bb0e42855a ("dt-bindings: memory: mediatek: Convert SMI to DT schema") renamed: Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt to: Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml. Update its cross-references accordingly. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Link: https://lore.kernel.org/r/c70bd79b311a65babe7374eaf81974563400a943.1610535350.git.mchehab+huawei@kernel.org Signed-off-by: Rob Herring <[email protected]>
2021-01-25dt-bindings: display: mediatek: update mediatek,dpi.yaml referenceMauro Carvalho Chehab1-1/+1
Changeset 9273cf7d3942 ("dt-bindings: display: mediatek: convert the dpi bindings to yaml") renamed: Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt to: Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml. Update its cross-reference accordingly. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Link: https://lore.kernel.org/r/3bf906f39b797d18800abd387187cce71296e5eb.1610535350.git.mchehab+huawei@kernel.org Signed-off-by: Rob Herring <[email protected]>
2021-01-25ASoC: audio-graph-card: update audio-graph-card.yaml referenceMauro Carvalho Chehab1-1/+1
Changeset 97198614f6c3 ("ASoC: audio-graph-card: switch to yaml base Documentation") renamed: Documentation/devicetree/bindings/sound/audio-graph-card.txt to: Documentation/devicetree/bindings/sound/audio-graph-card.yaml. Update its cross-reference accordingly. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Link: https://lore.kernel.org/r/8a779e6b9644d19c5d77b382059f6ccf9781434d.1610535350.git.mchehab+huawei@kernel.org Signed-off-by: Rob Herring <[email protected]>
2021-01-25Merge tag 'printk-for-5.11-urgent-fixup' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux Pull printk fix from Petr Mladek: "The fix of a potential buffer overflow in 5.11-rc5 introduced another one. The trailing '\0' might be written up to the message "len" past the buffer. Fortunately, it is not that easy to hit. Most readers use 1kB buffers for a single message. Typical messages fit into the temporary buffer with enough reserve. Also readers do not rely on the '\0'. It is related to the previous fix. Some readers required the space for the trailing '\0'. We decided to write it there to avoid such regressions in the future. The most realistic victims are dumpers using kmsg_dump_get_buffer(). They are filling the entire buffer with as many messages as possible. They are typically used when handling panic()" * tag 'printk-for-5.11-urgent-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: printk: fix string termination for record_print_text()
2021-01-25nbd: freeze the queue while we're adding connectionsJosef Bacik1-0/+8
When setting up a device, we can krealloc the config->socks array to add new sockets to the configuration. However if we happen to get a IO request in at this point even though we aren't setup we could hit a UAF, as we deref config->socks without any locking, assuming that the configuration was setup already and that ->socks is safe to access it as we have a reference on the configuration. But there's nothing really preventing IO from occurring at this point of the device setup, we don't want to incur the overhead of a lock to access ->socks when it will never change while the device is running. To fix this UAF scenario simply freeze the queue if we are adding sockets. This will protect us from this particular case without adding any additional overhead for the normal running case. Cc: [email protected] Signed-off-by: Josef Bacik <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2021-01-25PM: hibernate: flush swap writer after markingLaurent Badel1-1/+1
Flush the swap writer after, not before, marking the files, to ensure the signature is properly written. Fixes: 6f612af57821 ("PM / Hibernate: Group swap ops") Signed-off-by: Laurent Badel <[email protected]> Cc: All applicable <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2021-01-25btrfs: fix log replay failure due to race with space cache rebuildFilipe Manana1-43/+18
After a sudden power failure we may end up with a space cache on disk that is not valid and needs to be rebuilt from scratch. If that happens, during log replay when we attempt to pin an extent buffer from a log tree, at btrfs_pin_extent_for_log_replay(), we do not wait for the space cache to be rebuilt through the call to: btrfs_cache_block_group(cache, 1); That is because that only waits for the task (work queue job) that loads the space cache to change the cache state from BTRFS_CACHE_FAST to any other value. That is ok when the space cache on disk exists and is valid, but when the cache is not valid and needs to be rebuilt, it ends up returning as soon as the cache state changes to BTRFS_CACHE_STARTED (done at caching_thread()). So this means that we can end up trying to unpin a range which is not yet marked as free in the block group. This results in the call to btrfs_remove_free_space() to return -EINVAL to btrfs_pin_extent_for_log_replay(), which in turn makes the log replay fail as well as mounting the filesystem. More specifically the -EINVAL comes from free_space_cache.c:remove_from_bitmap(), because the requested range is not marked as free space (ones in the bitmap), we have the following condition triggered: static noinline int remove_from_bitmap(struct btrfs_free_space_ctl *ctl, (...) if (ret < 0 || search_start != *offset) return -EINVAL; (...) It's the "search_start != *offset" that results in the condition being evaluated to true. When this happens we got the following in dmesg/syslog: [72383.415114] BTRFS: device fsid 32b95b69-0ea9-496a-9f02-3f5a56dc9322 devid 1 transid 1432 /dev/sdb scanned by mount (3816007) [72383.417837] BTRFS info (device sdb): disk space caching is enabled [72383.418536] BTRFS info (device sdb): has skinny extents [72383.423846] BTRFS info (device sdb): start tree-log replay [72383.426416] BTRFS warning (device sdb): block group 30408704 has wrong amount of free space [72383.427686] BTRFS warning (device sdb): failed to load free space cache for block group 30408704, rebuilding it now [72383.454291] BTRFS: error (device sdb) in btrfs_recover_log_trees:6203: errno=-22 unknown (Failed to pin buffers while recovering log root tree.) [72383.456725] BTRFS: error (device sdb) in btrfs_replay_log:2253: errno=-22 unknown (Failed to recover log tree) [72383.460241] BTRFS error (device sdb): open_ctree failed We also mark the range for the extent buffer in the excluded extents io tree. That is fine when the space cache is valid on disk and we can load it, in which case it causes no problems. However, for the case where we need to rebuild the space cache, because it is either invalid or it is missing, having the extent buffer range marked in the excluded extents io tree leads to a -EINVAL failure from the call to btrfs_remove_free_space(), resulting in the log replay and mount to fail. This is because by having the range marked in the excluded extents io tree, the caching thread ends up never adding the range of the extent buffer as free space in the block group since the calls to add_new_free_space(), called from load_extent_tree_free(), filter out any ranges that are marked as excluded extents. So fix this by making sure that during log replay we wait for the caching task to finish completely when we need to rebuild a space cache, and also drop the need to mark the extent buffer range in the excluded extents io tree, as well as clearing ranges from that tree at btrfs_finish_extent_commit(). This started to happen with some frequency on large filesystems having block groups with a lot of fragmentation since the recent commit e747853cae3ae3 ("btrfs: load free space cache asynchronously"), but in fact the issue has been there for years, it was just much less likely to happen. Reviewed-by: Josef Bacik <[email protected]> Signed-off-by: Filipe Manana <[email protected]> Signed-off-by: David Sterba <[email protected]>
2021-01-25btrfs: fix lockdep warning due to seqcount_mutex on 32bit archSu Yue2-6/+7
This effectively reverts commit d5c8238849e7 ("btrfs: convert data_seqcount to seqcount_mutex_t"). While running fstests on 32 bits test box, many tests failed because of warnings in dmesg. One of those warnings (btrfs/003): [66.441317] WARNING: CPU: 6 PID: 9251 at include/linux/seqlock.h:279 btrfs_remove_chunk+0x58b/0x7b0 [btrfs] [66.441446] CPU: 6 PID: 9251 Comm: btrfs Tainted: G O 5.11.0-rc4-custom+ #5 [66.441449] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ArchLinux 1.14.0-1 04/01/2014 [66.441451] EIP: btrfs_remove_chunk+0x58b/0x7b0 [btrfs] [66.441472] EAX: 00000000 EBX: 00000001 ECX: c576070c EDX: c6b15803 [66.441475] ESI: 10000000 EDI: 00000000 EBP: c56fbcfc ESP: c56fbc70 [66.441477] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 EFLAGS: 00010246 [66.441481] CR0: 80050033 CR2: 05c8da20 CR3: 04b20000 CR4: 00350ed0 [66.441485] Call Trace: [66.441510] btrfs_relocate_chunk+0xb1/0x100 [btrfs] [66.441529] ? btrfs_lookup_block_group+0x17/0x20 [btrfs] [66.441562] btrfs_balance+0x8ed/0x13b0 [btrfs] [66.441586] ? btrfs_ioctl_balance+0x333/0x3c0 [btrfs] [66.441619] ? __this_cpu_preempt_check+0xf/0x11 [66.441643] btrfs_ioctl_balance+0x333/0x3c0 [btrfs] [66.441664] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs] [66.441683] btrfs_ioctl+0x414/0x2ae0 [btrfs] [66.441700] ? __lock_acquire+0x35f/0x2650 [66.441717] ? lockdep_hardirqs_on+0x87/0x120 [66.441720] ? lockdep_hardirqs_on_prepare+0xd0/0x1e0 [66.441724] ? call_rcu+0x2d3/0x530 [66.441731] ? __might_fault+0x41/0x90 [66.441736] ? kvm_sched_clock_read+0x15/0x50 [66.441740] ? sched_clock+0x8/0x10 [66.441745] ? sched_clock_cpu+0x13/0x180 [66.441750] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs] [66.441750] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs] [66.441768] __ia32_sys_ioctl+0x165/0x8a0 [66.441773] ? __this_cpu_preempt_check+0xf/0x11 [66.441785] ? __might_fault+0x89/0x90 [66.441791] __do_fast_syscall_32+0x54/0x80 [66.441796] do_fast_syscall_32+0x32/0x70 [66.441801] do_SYSENTER_32+0x15/0x20 [66.441805] entry_SYSENTER_32+0x9f/0xf2 [66.441808] EIP: 0xab7b5549 [66.441814] EAX: ffffffda EBX: 00000003 ECX: c4009420 EDX: bfa91f5c [66.441816] ESI: 00000003 EDI: 00000001 EBP: 00000000 ESP: bfa91e98 [66.441818] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 007b EFLAGS: 00000292 [66.441833] irq event stamp: 42579 [66.441835] hardirqs last enabled at (42585): [<c60eb065>] console_unlock+0x495/0x590 [66.441838] hardirqs last disabled at (42590): [<c60eafd5>] console_unlock+0x405/0x590 [66.441840] softirqs last enabled at (41698): [<c601b76c>] call_on_stack+0x1c/0x60 [66.441843] softirqs last disabled at (41681): [<c601b76c>] call_on_stack+0x1c/0x60 ======================================================================== btrfs_remove_chunk+0x58b/0x7b0: __seqprop_mutex_assert at linux/./include/linux/seqlock.h:279 (inlined by) btrfs_device_set_bytes_used at linux/fs/btrfs/volumes.h:212 (inlined by) btrfs_remove_chunk at linux/fs/btrfs/volumes.c:2994 ======================================================================== The warning is produced by lockdep_assert_held() in __seqprop_mutex_assert() if CONFIG_LOCKDEP is enabled. And "olumes.c:2994 is btrfs_device_set_bytes_used() with mutex lock fs_info->chunk_mutex held already. After adding some debug prints, the cause was found that many __alloc_device() are called with NULL @fs_info (during scanning ioctl). Inside the function, btrfs_device_data_ordered_init() is expanded to seqcount_mutex_init(). In this scenario, its second parameter info->chunk_mutex is &NULL->chunk_mutex which equals to offsetof(struct btrfs_fs_info, chunk_mutex) unexpectedly. Thus, seqcount_mutex_init() is called in wrong way. And later btrfs_device_get/set helpers trigger lockdep warnings. The device and filesystem object lifetimes are different and we'd have to synchronize initialization of the btrfs_device::data_seqcount with the fs_info, possibly using some additional synchronization. It would still not prevent concurrent access to the seqcount lock when it's used for read and initialization. Commit d5c8238849e7 ("btrfs: convert data_seqcount to seqcount_mutex_t") does not mention a particular problem being fixed so revert should not cause any harm and we'll get the lockdep warning fixed. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=210139 Reported-by: Erhard F <[email protected]> Fixes: d5c8238849e7 ("btrfs: convert data_seqcount to seqcount_mutex_t") CC: [email protected] # 5.10 CC: Davidlohr Bueso <[email protected]> Signed-off-by: Su Yue <[email protected]> Reviewed-by: David Sterba <[email protected]> Signed-off-by: David Sterba <[email protected]>
2021-01-25btrfs: fix possible free space tree corruption with online conversionJosef Bacik3-2/+21
While running btrfs/011 in a loop I would often ASSERT() while trying to add a new free space entry that already existed, or get an EEXIST while adding a new block to the extent tree, which is another indication of double allocation. This occurs because when we do the free space tree population, we create the new root and then populate the tree and commit the transaction. The problem is when you create a new root, the root node and commit root node are the same. During this initial transaction commit we will run all of the delayed refs that were paused during the free space tree generation, and thus begin to cache block groups. While caching block groups the caching thread will be reading from the main root for the free space tree, so as we make allocations we'll be changing the free space tree, which can cause us to add the same range twice which results in either the ASSERT(ret != -EEXIST); in __btrfs_add_free_space, or in a variety of different errors when running delayed refs because of a double allocation. Fix this by marking the fs_info as unsafe to load the free space tree, and fall back on the old slow method. We could be smarter than this, for example caching the block group while we're populating the free space tree, but since this is a serious problem I've opted for the simplest solution. CC: [email protected] # 4.9+ Fixes: a5ed91828518 ("Btrfs: implement the free space B-tree") Reviewed-by: Filipe Manana <[email protected]> Signed-off-by: Josef Bacik <[email protected]> Signed-off-by: David Sterba <[email protected]>
2021-01-25kernel: kexec: remove the lock operation of system_transition_mutexBaoquan He1-2/+0
Function kernel_kexec() is called with lock system_transition_mutex held in reboot system call. While inside kernel_kexec(), it will acquire system_transition_mutex agin. This will lead to dead lock. The dead lock should be easily triggered, it hasn't caused any failure report just because the feature 'kexec jump' is almost not used by anyone as far as I know. An inquiry can be made about who is using 'kexec jump' and where it's used. Before that, let's simply remove the lock operation inside CONFIG_KEXEC_JUMP ifdeffery scope. Fixes: 55f2503c3b69 ("PM / reboot: Eliminate race between reboot and suspend") Signed-off-by: Baoquan He <[email protected]> Reported-by: Dan Carpenter <[email protected]> Reviewed-by: Pingfan Liu <[email protected]> Cc: 4.19+ <[email protected]> # 4.19+ Signed-off-by: Rafael J. Wysocki <[email protected]>
2021-01-25s390/dasd: Fix inconsistent kobject removalJan Höppner3-8/+17
Our intention was to only remove path kobjects whenever a device is being set offline. However, one corner case was missing. If a device is disabled and enabled (using the IOCTLs BIODASDDISABLE and BIODASDENABLE respectively), the enabling process will call dasd_eckd_reload_device() which itself calls dasd_eckd_read_conf() in order to update path information. During that update, dasd_eckd_clear_conf_data() clears all old data and also removes all kobjects. This will leave us with an inconsistent state of path kobjects and a subsequent path verification leads to a failing kobject creation. Fix this by removing kobjects only in the context of offlining a device as initially intended. Fixes: 19508b204740 ("s390/dasd: Display FC Endpoint Security information via sysfs") Reported-by: Stefan Haberland <[email protected]> Signed-off-by: Jan Höppner <[email protected]> Reviewed-by: Stefan Haberland <[email protected]> Reviewed-by: Cornelia Huck <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2021-01-25ACPI: thermal: Do not call acpi_thermal_check() directlyRafael J. Wysocki1-13/+33
Calling acpi_thermal_check() from acpi_thermal_notify() directly is problematic if _TMP triggers Notify () on the thermal zone for which it has been evaluated (which happens on some systems), because it causes a new acpi_thermal_notify() invocation to be queued up every time and if that takes place too often, an indefinite number of pending work items may accumulate in kacpi_notify_wq over time. Besides, it is not really useful to queue up a new invocation of acpi_thermal_check() if one of them is pending already. For these reasons, rework acpi_thermal_notify() to queue up a thermal check instead of calling acpi_thermal_check() directly and only allow one thermal check to be pending at a time. Moreover, only allow one acpi_thermal_check_fn() instance at a time to run thermal_zone_device_update() for one thermal zone and make it return early if it sees other instances running for the same thermal zone. While at it, fold acpi_thermal_check() into acpi_thermal_check_fn(), as it is only called from there after the other changes made here. [This issue appears to have been exposed by commit 6d25be5782e4 ("sched/core, workqueues: Distangle worker accounting from rq lock"), but it is unclear why it was not visible earlier.] BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208877 Reported-by: Stephen Berman <[email protected]> Diagnosed-by: Sebastian Andrzej Siewior <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]> Reviewed-by: Sebastian Andrzej Siewior <[email protected]> Tested-by: Stephen Berman <[email protected]> Cc: All applicable <[email protected]>
2021-01-25ACPI: sysfs: Prefer "compatible" modaliasKai-Heng Feng1-14/+6
Commit 8765c5ba1949 ("ACPI / scan: Rework modalias creation when "compatible" is present") may create two "MODALIAS=" in one uevent file if specific conditions are met. This breaks systemd-udevd, which assumes each "key" in one uevent file to be unique. The internal implementation of systemd-udevd overwrites the first MODALIAS with the second one, so its kmod rule doesn't load the driver for the first MODALIAS. So if both the ACPI modalias and the OF modalias are present, use the latter to ensure that there will be only one MODALIAS. Link: https://github.com/systemd/systemd/pull/18163 Suggested-by: Mika Westerberg <[email protected]> Fixes: 8765c5ba1949 ("ACPI / scan: Rework modalias creation when "compatible" is present") Signed-off-by: Kai-Heng Feng <[email protected]> Reviewed-by: Mika Westerberg <[email protected]> Reviewed-by: Greg Kroah-Hartman <[email protected]> Cc: 4.1+ <[email protected]> # 4.1+ [ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <[email protected]>
2021-01-25Merge series "ASoC: SOF: partial fix to Kconfig issues" from Pierre-Louis ↵Mark Brown3-10/+14
Bossart <[email protected]>: We've had several reports of broken dependencies. The 'right' fix is to revisit the module dependencies as suggested by Arnd Bergmann. This is WIP at https://github.com/thesofproject/linux/pull/2683. Since this is taking longer than expected, I am only sharing quick fixes for now. Pierre-Louis Bossart (2): ASoC: SOF: Intel: soundwire: fix select/depend unmet dependencies ASoC: SOF: SND_INTEL_DSP_CONFIG dependency sound/soc/sof/intel/Kconfig | 3 ++- sound/soc/sof/sof-acpi-dev.c | 11 ++++++----- sound/soc/sof/sof-pci-dev.c | 10 ++++++---- 3 files changed, 14 insertions(+), 10 deletions(-) -- 2.25.1
2021-01-25mt7601u: fix kernel crash unplugging the deviceLorenzo Bianconi1-1/+1
The following crash log can occur unplugging the usb dongle since, after the urb poison in mt7601u_free_tx_queue(), usb_submit_urb() will always fail resulting in a skb kfree while the skb has been already queued. Fix the issue enqueuing the skb only if usb_submit_urb() succeed. Hardware name: Hewlett-Packard 500-539ng/2B2C, BIOS 80.06 04/01/2015 Workqueue: usb_hub_wq hub_event RIP: 0010:skb_trim+0x2c/0x30 RSP: 0000:ffffb4c88005bba8 EFLAGS: 00010206 RAX: 000000004ad483ee RBX: ffff9a236625dee0 RCX: 000000000000662f RDX: 000000000000000c RSI: 0000000000000000 RDI: ffff9a2343179300 RBP: ffff9a2343179300 R08: 0000000000000001 R09: 0000000000000000 R10: ffff9a23748f7840 R11: 0000000000000001 R12: ffff9a236625e4d4 R13: ffff9a236625dee0 R14: 0000000000001080 R15: 0000000000000008 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fd410a34ef8 CR3: 00000001416ee001 CR4: 00000000001706f0 Call Trace: mt7601u_tx_status+0x3e/0xa0 [mt7601u] mt7601u_dma_cleanup+0xca/0x110 [mt7601u] mt7601u_cleanup+0x22/0x30 [mt7601u] mt7601u_disconnect+0x22/0x60 [mt7601u] usb_unbind_interface+0x8a/0x270 ? kernfs_find_ns+0x35/0xd0 __device_release_driver+0x17a/0x230 device_release_driver+0x24/0x30 bus_remove_device+0xdb/0x140 device_del+0x18b/0x430 ? kobject_put+0x98/0x1d0 usb_disable_device+0xc6/0x1f0 usb_disconnect.cold+0x7e/0x20a hub_event+0xbf3/0x1870 process_one_work+0x1b6/0x350 worker_thread+0x53/0x3e0 ? process_one_work+0x350/0x350 kthread+0x11b/0x140 ? __kthread_bind_mask+0x60/0x60 ret_from_fork+0x22/0x30 Fixes: 23377c200b2eb ("mt7601u: fix possible memory leak when the device is disconnected") Signed-off-by: Lorenzo Bianconi <[email protected]> Acked-by: Jakub Kicinski <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/3b85219f669a63a8ced1f43686de05915a580489.1610919247.git.lorenzo@kernel.org
2021-01-25iwlwifi: queue: bail out on invalid freeingJohannes Berg1-4/+2
If we find an entry without an SKB, we currently continue, but that will just result in an infinite loop since we won't increment the read pointer, and will try the same thing over and over again. Fix this. Signed-off-by: Johannes Berg <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20210122144849.abe2dedcc3ac.Ia6b03f9eeb617fd819e56dd5376f4bb8edc7b98a@changeid
2021-01-25iwlwifi: mvm: guard against device removal in reprobeJohannes Berg1-1/+2
If we get into a problem severe enough to attempt a reprobe, we schedule a worker to do that. However, if the problem gets more severe and the device is actually destroyed before this worker has a chance to run, we use a free device. Bump up the reference count of the device until the worker runs to avoid this situation. Signed-off-by: Johannes Berg <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20210122144849.871f0892e4b2.I94819e11afd68d875f3e242b98bef724b8236f1e@changeid
2021-01-25iwlwifi: Fix IWL_SUBDEVICE_NO_160 macro to use the correct bit.Matti Gottlieb1-2/+2
The bit that indicates if the device supports 160MHZ is bit #9. The macro checks bit #8. Fix IWL_SUBDEVICE_NO_160 macro to use the correct bit. Signed-off-by: Matti Gottlieb <[email protected]> Fixes: d6f2134a3831 ("iwlwifi: add mac/rf types and 160MHz to the device tables") Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20210122144849.bddbf9b57a75.I16e09e2b1404b16bfff70852a5a654aa468579e2@changeid
2021-01-25iwlwifi: mvm: clear IN_D3 after wowlan status cmdShaul Triebitz1-3/+3
In D3 resume flow, avoid the following race where sending packets before updating the sequence number (sequence number received from the wowlan status command response): Thread 1: __iwl_mvm_resume clears IWL_MVM_STATUS_IN_D3 and is cut by thread 2 before reaching iwl_mvm_query_wakeup_reasons. Thread 2: iwl_mvm_mac_itxq_xmit calls iwl_mvm_tx_skb since IWL_MVM_STATUS_IN_D3 is not set using a wrong sequence number. Thread 1: __iwl_mvm_resume continues and calls iwl_mvm_query_wakeup_reasons updating the sequence number received from the firmware. The next packet that will be sent now will cause sysassert 0x1096. Fix the bug by moving 'clear IWL_MVM_STATUS_IN_D3' to after sending the wowlan status command and updating the sequence number. Signed-off-by: Shaul Triebitz <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20210122144849.fe927ec939c6.I103d3321fb55da7e6c6c51582cfadf94eb8b6c58@changeid
2021-01-25iwlwifi: pcie: add rules to match Qu with Hr2Luca Coelho3-0/+38
Until now we have been relying on matching the PCI ID and subsystem device ID in order to recognize Qu devices with Hr2. Add rules to match these devices, so that we don't have to add a new rule for every new ID we get. Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20210122144849.591ce253ddd8.Ia4b9cc2c535625890c6d6b560db97ee9f2d5ca3b@changeid
2021-01-25iwlwifi: mvm: invalidate IDs of internal stations at mvm startGregory Greenman2-0/+10
Having sta_id not set for aux_sta and snif_sta can potentially lead to a hard to debug issue in case remove station is called without an add. In this case sta_id 0, an unrelated regular station, will be removed. In fact, we do have a FW assert that occures rarely and from the debug data analysis it looks like sta_id 0 is removed by mistake, though it's hard to pinpoint the exact flow. The WARN_ON in this patch should help to find it. Signed-off-by: Gregory Greenman <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20210122144849.5dc6dd9b22d5.I2add1b5ad24d0d0a221de79d439c09f88fcaf15d@changeid
2021-01-25iwlwifi: mvm: fix the return type for DSM functions 1 and 2Matt Chen3-29/+68
The return type value of functions 1 and 2 were considered to be an integer inside a buffer, but they can also be only an integer, without the buffer. Fix the code in iwl_acpi_get_dsm_u8() to handle it as a single integer value, as well as packed inside a buffer. Signed-off-by: Matt Chen <[email protected]> Fixes: 9db93491f29e ("iwlwifi: acpi: support device specific method (DSM)") Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20210122144849.5757092adcd6.Ic24524627b899c9a01af38107a62a626bdf5ae3a@changeid
2021-01-25iwlwifi: pcie: reschedule in long-running memory readsJohannes Berg1-1/+7
If we spin for a long time in memory reads that (for some reason in hardware) take a long time, then we'll eventually get messages such as watchdog: BUG: soft lockup - CPU#2 stuck for 24s! [kworker/2:2:272] This is because the reading really does take a very long time, and we don't schedule, so we're hogging the CPU with this task, at least if CONFIG_PREEMPT is not set, e.g. with CONFIG_PREEMPT_VOLUNTARY=y. Previously I misinterpreted the situation and thought that this was only going to happen if we had interrupts disabled, and then fixed this (which is good anyway, however), but that didn't always help; looking at it again now I realized that the spin unlock will only reschedule if CONFIG_PREEMPT is used. In order to avoid this issue, change the code to cond_resched() if we've been spinning for too long here. Signed-off-by: Johannes Berg <[email protected]> Fixes: 04516706bb99 ("iwlwifi: pcie: limit memory read spin time") Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20210115130253.217a9d6a6a12.If964cb582ab0aaa94e81c4ff3b279eaafda0fd3f@changeid
2021-01-25iwlwifi: pcie: use jiffies for memory read spin time limitJohannes Berg1-6/+2
There's no reason to use ktime_get() since we don't need any better precision than jiffies, and since we no longer disable interrupts around this code (when grabbing NIC access), jiffies will work fine. Use jiffies instead of ktime_get(). This cleanup is preparation for the following patch "iwlwifi: pcie: reschedule in long-running memory reads". The code gets simpler with the weird clock use etc. removed before we add cond_resched(). Signed-off-by: Johannes Berg <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20210115130253.621c948b1fad.I3ee9f4bc4e74a0c9125d42fb7c35cd80df4698a1@changeid
2021-01-25iwlwifi: pcie: fix context info memory leakJohannes Berg1-2/+9
If the image loader allocation fails, we leak all the previously allocated memory. Fix this. Signed-off-by: Johannes Berg <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20210115130252.97172cbaa67c.I3473233d0ad01a71aa9400832fb2b9f494d88a11@changeid
2021-01-25iwlwifi: pcie: add a NULL check in iwl_pcie_txq_unmapEmmanuel Grumbach1-0/+5
I hit a NULL pointer exception in this function when the init flow went really bad. Signed-off-by: Emmanuel Grumbach <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20210115130252.2e8da9f2c132.I0234d4b8ddaf70aaa5028a20c863255e05bc1f84@changeid
Powered by cgit, Gruvboxed by Blaster4385.