aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2017-03-28net: moxa: fix TX overrun memory leakJonas Jensen2-2/+19
moxart_mac_start_xmit() doesn't care where tx_tail is, tx_head can catch and pass tx_tail, which is bad because moxart_tx_finished() isn't guaranteed to catch up on freeing resources from tx_tail. Add a check in moxart_mac_start_xmit() stopping the queue at the end of the circular buffer. Also add a check in moxart_tx_finished() waking the queue if the buffer has TX_WAKE_THRESHOLD or more free descriptors. While we're at it, move spin_lock_irq() to happen before our descriptor pointer is assigned in moxart_mac_start_xmit(). Addresses https://bugzilla.kernel.org/show_bug.cgi?id=99451 Signed-off-by: Jonas Jensen <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-28isdn: kcapi: avoid uninitialized dataArnd Bergmann1-0/+1
gcc-7 points out that the AVMB1_ADDCARD ioctl results in an unintialized value ending up in the cardnr parameter: drivers/isdn/capi/kcapi.c: In function 'old_capi_manufacturer': drivers/isdn/capi/kcapi.c:1042:24: error: 'cdef.cardnr' may be used uninitialized in this function [-Werror=maybe-uninitialized] cparams.cardnr = cdef.cardnr; This has been broken since before the start of the git history, so either the value is not used for anything important, or the ioctl command doesn't get called in practice. Setting the cardnr to zero avoids the warning and makes sure we have consistent behavior. Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-28sctp: change to save MSG_MORE flag into assocXin Long3-3/+3
David Laight noticed the support for MSG_MORE with datamsg->force_delay didn't really work as we expected, as the first msg with MSG_MORE set would always block the following chunks' dequeuing. This Patch is to rewrite it by saving the MSG_MORE flag into assoc as David Laight suggested. asoc->force_delay is used to save MSG_MORE flag before a msg is sent. All chunks in queue would not be sent out if asoc->force_delay is set by the msg with MSG_MORE flag, until a new msg without MSG_MORE flag clears asoc->force_delay. Note that this change would not affect the flush is generated by other triggers, like asoc->state != ESTABLISHED, queue size > pmtu etc. v1->v2: Not clear asoc->force_delay after sending the msg with MSG_MORE flag. Fixes: 4ea0c32f5f42 ("sctp: add support for MSG_MORE") Signed-off-by: Xin Long <[email protected]> Acked-by: David Laight <[email protected]> Acked-by: Marcelo Ricardo Leitner <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-27net: ipconfig: fix ic_close_devs() use-after-freeMark Rutland1-1/+1
Our chosen ic_dev may be anywhere in our list of ic_devs, and we may free it before attempting to close others. When we compare d->dev and ic_dev->dev, we're potentially dereferencing memory returned to the allocator. This causes KASAN to scream for each subsequent ic_dev we check. As there's a 1-1 mapping between ic_devs and netdevs, we can instead compare d and ic_dev directly, which implicitly handles the !ic_dev case, and avoids the use-after-free. The ic_dev pointer may be stale, but we will not dereference it. Original splat: [ 6.487446] ================================================================== [ 6.494693] BUG: KASAN: use-after-free in ic_close_devs+0xc4/0x154 at addr ffff800367efa708 [ 6.503013] Read of size 8 by task swapper/0/1 [ 6.507452] CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.11.0-rc3-00002-gda42158 #8 [ 6.514993] Hardware name: AppliedMicro Mustang/Mustang, BIOS 3.05.05-beta_rc Jan 27 2016 [ 6.523138] Call trace: [ 6.525590] [<ffff200008094778>] dump_backtrace+0x0/0x570 [ 6.530976] [<ffff200008094d08>] show_stack+0x20/0x30 [ 6.536017] [<ffff200008bee928>] dump_stack+0x120/0x188 [ 6.541231] [<ffff20000856d5e4>] kasan_object_err+0x24/0xa0 [ 6.546790] [<ffff20000856d924>] kasan_report_error+0x244/0x738 [ 6.552695] [<ffff20000856dfec>] __asan_report_load8_noabort+0x54/0x80 [ 6.559204] [<ffff20000aae86ac>] ic_close_devs+0xc4/0x154 [ 6.564590] [<ffff20000aaedbac>] ip_auto_config+0x2ed4/0x2f1c [ 6.570321] [<ffff200008084b04>] do_one_initcall+0xcc/0x370 [ 6.575882] [<ffff20000aa31de8>] kernel_init_freeable+0x5f8/0x6c4 [ 6.581959] [<ffff20000a16df00>] kernel_init+0x18/0x190 [ 6.587171] [<ffff200008084710>] ret_from_fork+0x10/0x40 [ 6.592468] Object at ffff800367efa700, in cache kmalloc-128 size: 128 [ 6.598969] Allocated: [ 6.601324] PID = 1 [ 6.603427] save_stack_trace_tsk+0x0/0x418 [ 6.607603] save_stack_trace+0x20/0x30 [ 6.611430] kasan_kmalloc+0xd8/0x188 [ 6.615087] ip_auto_config+0x8c4/0x2f1c [ 6.619002] do_one_initcall+0xcc/0x370 [ 6.622832] kernel_init_freeable+0x5f8/0x6c4 [ 6.627178] kernel_init+0x18/0x190 [ 6.630660] ret_from_fork+0x10/0x40 [ 6.634223] Freed: [ 6.636233] PID = 1 [ 6.638334] save_stack_trace_tsk+0x0/0x418 [ 6.642510] save_stack_trace+0x20/0x30 [ 6.646337] kasan_slab_free+0x88/0x178 [ 6.650167] kfree+0xb8/0x478 [ 6.653131] ic_close_devs+0x130/0x154 [ 6.656875] ip_auto_config+0x2ed4/0x2f1c [ 6.660875] do_one_initcall+0xcc/0x370 [ 6.664705] kernel_init_freeable+0x5f8/0x6c4 [ 6.669051] kernel_init+0x18/0x190 [ 6.672534] ret_from_fork+0x10/0x40 [ 6.676098] Memory state around the buggy address: [ 6.680880] ffff800367efa600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 6.688078] ffff800367efa680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 6.695276] >ffff800367efa700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 6.702469] ^ [ 6.705952] ffff800367efa780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 6.713149] ffff800367efa800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 6.720343] ================================================================== [ 6.727536] Disabling lock debugging due to kernel taint Signed-off-by: Mark Rutland <[email protected]> Cc: Alexey Kuznetsov <[email protected]> Cc: David S. Miller <[email protected]> Cc: Hideaki YOSHIFUJI <[email protected]> Cc: James Morris <[email protected]> Cc: Patrick McHardy <[email protected]> Cc: [email protected] Signed-off-by: David S. Miller <[email protected]>
2017-03-27MAINTAINERS: Add Andrew Lunn as co-maintainer of PHYLIBFlorian Fainelli1-0/+1
Andrew has been contributing a lot to PHYLIB over the past months and his feedback on patches is more than welcome. Signed-off-by: Florian Fainelli <[email protected]> Acked-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-27netfilter: nf_nat_snmp: Fix panic when snmp_trap_helper fails to registerGao Feng1-18/+1
In the commit 93557f53e1fb ("netfilter: nf_conntrack: nf_conntrack snmp helper"), the snmp_helper is replaced by nf_nat_snmp_hook. So the snmp_helper is never registered. But it still tries to unregister the snmp_helper, it could cause the panic. Now remove the useless snmp_helper and the unregister call in the error handler. Fixes: 93557f53e1fb ("netfilter: nf_conntrack: nf_conntrack snmp helper") Signed-off-by: Gao Feng <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
2017-03-27netfilter: nf_ct_ext: fix possible panic after nf_ct_extend_unregisterLiping Zhang1-3/+10
If one cpu is doing nf_ct_extend_unregister while another cpu is doing __nf_ct_ext_add_length, then we may hit BUG_ON(t == NULL). Moreover, there's no synchronize_rcu invocation after set nf_ct_ext_types[id] to NULL, so it's possible that we may access invalid pointer. But actually, most of the ct extends are built-in, so the problem listed above will not happen. However, there are two exceptions: NF_CT_EXT_NAT and NF_CT_EXT_SYNPROXY. For _EXT_NAT, the panic will not happen, since adding the nat extend and unregistering the nat extend are located in the same file(nf_nat_core.c), this means that after the nat module is removed, we cannot add the nat extend too. For _EXT_SYNPROXY, synproxy extend may be added by init_conntrack, while synproxy extend unregister will be done by synproxy_core_exit. So after nf_synproxy_core.ko is removed, we may still try to add the synproxy extend, then kernel panic may happen. I know it's very hard to reproduce this issue, but I can play a tricky game to make it happen very easily :) Step 1. Enable SYNPROXY for tcp dport 1234 at FORWARD hook: # iptables -I FORWARD -p tcp --dport 1234 -j SYNPROXY Step 2. Queue the syn packet to the userspace at raw table OUTPUT hook. Also note, in the userspace we only add a 20s' delay, then reinject the syn packet to the kernel: # iptables -t raw -I OUTPUT -p tcp --syn -j NFQUEUE --queue-num 1 Step 3. Using "nc 2.2.2.2 1234" to connect the server. Step 4. Now remove the nf_synproxy_core.ko quickly: # iptables -F FORWARD # rmmod ipt_SYNPROXY # rmmod nf_synproxy_core Step 5. After 20s' delay, the syn packet is reinjected to the kernel. Now you will see the panic like this: kernel BUG at net/netfilter/nf_conntrack_extend.c:91! Call Trace: ? __nf_ct_ext_add_length+0x53/0x3c0 [nf_conntrack] init_conntrack+0x12b/0x600 [nf_conntrack] nf_conntrack_in+0x4cc/0x580 [nf_conntrack] ipv4_conntrack_local+0x48/0x50 [nf_conntrack_ipv4] nf_reinject+0x104/0x270 nfqnl_recv_verdict+0x3e1/0x5f9 [nfnetlink_queue] ? nfqnl_recv_verdict+0x5/0x5f9 [nfnetlink_queue] ? nla_parse+0xa0/0x100 nfnetlink_rcv_msg+0x175/0x6a9 [nfnetlink] [...] One possible solution is to make NF_CT_EXT_SYNPROXY extend built-in, i.e. introduce nf_conntrack_synproxy.c and only do ct extend register and unregister in it, similar to nf_conntrack_timeout.c. But having such a obscure restriction of nf_ct_extend_unregister is not a good idea, so we should invoke synchronize_rcu after set nf_ct_ext_types to NULL, and check the NULL pointer when do __nf_ct_ext_add_length. Then it will be easier if we add new ct extend in the future. Last, we use kfree_rcu to free nf_ct_ext, so rcu_barrier() is unnecessary anymore, remove it too. Signed-off-by: Liping Zhang <[email protected]> Acked-by: Florian Westphal <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
2017-03-27netfilter: nfnl_cthelper: fix a race when walk the nf_ct_helper_hash tableLiping Zhang1-96/+81
The nf_ct_helper_hash table is protected by nf_ct_helper_mutex, while nfct_helper operation is protected by nfnl_lock(NFNL_SUBSYS_CTHELPER). So it's possible that one CPU is walking the nf_ct_helper_hash for cthelper add/get/del, another cpu is doing nf_conntrack_helpers_unregister at the same time. This is dangrous, and may cause use after free error. Note, delete operation will flush all cthelpers added via nfnetlink, so using rcu to do protect is not easy. Now introduce a dummy list to record all the cthelpers added via nfnetlink, then we can walk the dummy list instead of walking the nf_ct_helper_hash. Also, keep nfnl_cthelper_dump_table unchanged, it may be invoked without nfnl_lock(NFNL_SUBSYS_CTHELPER) held. Signed-off-by: Liping Zhang <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
2017-03-27netfilter: invoke synchronize_rcu after set the _hook_ to NULLLiping Zhang5-1/+7
Otherwise, another CPU may access the invalid pointer. For example: CPU0 CPU1 - rcu_read_lock(); - pfunc = _hook_; _hook_ = NULL; - mod unload - - pfunc(); // invalid, panic - rcu_read_unlock(); So we must call synchronize_rcu() to wait the rcu reader to finish. Also note, in nf_nat_snmp_basic_fini, synchronize_rcu() will be invoked by later nf_conntrack_helper_unregister, but I'm inclined to add a explicit synchronize_rcu after set the nf_nat_snmp_hook to NULL. Depend on such obscure assumptions is not a good idea. Last, in nfnetlink_cttimeout, we use kfree_rcu to free the time object, so in cttimeout_exit, invoking rcu_barrier() is not necessary at all, remove it too. Signed-off-by: Liping Zhang <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
2017-03-25irda: vlsi_ir: fix check for DMA mapping errorsAlexey Khoroshilov1-4/+4
vlsi_alloc_ring() checks for DMA mapping errors by comparing returned address with zero, while pci_dma_mapping_error() should be used. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-25net: hns: avoid gcc-7.0.1 warning for uninitialized dataArnd Bergmann1-0/+1
hns_dsaf_set_mac_key() calls dsaf_set_field() on an uninitialized field, which will then change only a few of its bits, causing a warning with the latest gcc: hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_mac_uc_entry': hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized] (origin) &= (~(mask)); \ ^~ hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_mac_mc_entry': hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_add_mac_mc_port': hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_del_mac_entry': hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_rm_mac_addr': hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_del_mac_mc_port': hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_mac_uc_entry': hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_mac_mc_entry': hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized] The code is actually correct since we always set all 16 bits of the port_vlan field, but gcc correctly points out that the first access does contain uninitialized data. This initializes the field to zero first before setting the individual bits. Fixes: 5483bfcb169c ("net: hns: modify tcam table and set mac key") Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-25net: hns: fix uninitialized data useArnd Bergmann1-2/+3
When dev_dbg() is enabled, we print uninitialized data, as gcc-7.0.1 now points out: ethernet/hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_promisc_tcam': ethernet/hisilicon/hns/hns_dsaf_main.c:2947:75: error: 'tbl_tcam_data.low.val' may be used uninitialized in this function [-Werror=maybe-uninitialized] ethernet/hisilicon/hns/hns_dsaf_main.c:2947:75: error: 'tbl_tcam_data.high.val' may be used uninitialized in this function [-Werror=maybe-uninitialized] We also pass the data into hns_dsaf_tcam_mc_cfg(), which might later use it (not sure about that), so it seems safer to just always initialize the tbl_tcam_data structure. Fixes: 1f5fa2dd1cfa ("net: hns: fix for promisc mode in HNS driver") Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24bpf: improve verifier packet range checksAlexei Starovoitov2-2/+23
llvm can optimize the 'if (ptr > data_end)' checks to be in the order slightly different than the original C code which will confuse verifier. Like: if (ptr + 16 > data_end) return TC_ACT_SHOT; // may be followed by if (ptr + 14 > data_end) return TC_ACT_SHOT; while llvm can see that 'ptr' is valid for all 16 bytes, the verifier could not. Fix verifier logic to account for such case and add a test. Reported-by: Huapeng Zhou <[email protected]> Fixes: 969bf05eb3ce ("bpf: direct packet access") Signed-off-by: Alexei Starovoitov <[email protected]> Acked-by: Daniel Borkmann <[email protected]> Acked-by: Martin KaFai Lau <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24ping: implement proper lockingEric Dumazet1-2/+3
We got a report of yet another bug in ping http://www.openwall.com/lists/oss-security/2017/03/24/6 ->disconnect() is not called with socket lock held. Fix this by acquiring ping rwlock earlier. Thanks to Daniel, Alexander and Andrey for letting us know this problem. Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind") Signed-off-by: Eric Dumazet <[email protected]> Reported-by: Daniel Jiang <[email protected]> Reported-by: Solar Designer <[email protected]> Reported-by: Andrey Konovalov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24i40e: Do not enable NAPI on q_vectors that have no ringsAlexander Duyck1-4/+12
When testing the epoll w/ busy poll code I found that I could get into a state where the i40e driver had q_vectors w/ active NAPI that had no rings. This was resulting in a divide by zero error. To correct it I am updating the driver code so that we only support NAPI on q_vectors that have 1 or more rings allocated to them. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24secure_seq: downgrade to per-host timestamp offsetsFlorian Westphal1-2/+29
Unfortunately too many devices (not under our control) use tcp_tw_recycle=1, which depends on timestamps being identical of the same saddr. Although tcp_tw_recycle got removed in net-next we can't make such end hosts disappear so downgrade to per-host timestamp offsets. Cc: Soheil Hassas Yeganeh <[email protected]> Cc: Eric Dumazet <[email protected]> Cc: Neal Cardwell <[email protected]> Cc: Yuchung Cheng <[email protected]> Reported-by: Yvan Vanrossomme <[email protected]> Fixes: 95a22caee396c ("tcp: randomize tcp timestamp offsets for each connection") Signed-off-by: Florian Westphal <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24net: Do not allow negative values for busy_read and busy_poll sysctl interfacesAlexander Duyck1-2/+4
This change basically codifies what I think was already the limitations on the busy_poll and busy_read sysctl interfaces. We weren't checking the lower bounds and as such could input negative values. The behavior when that was used was dependent on the architecture. In order to prevent any issues with that I am just disabling support for values less than 0 since this way we don't have to worry about any odd behaviors. By limiting the sysctl values this way it also makes it consistent with how we handle the SO_BUSY_POLL socket option since the value appears to be reported as a signed integer value and negative values are rejected. Signed-off-by: Alexander Duyck <[email protected]> Acked-by: Eric Dumazet <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24Revert "e1000e: driver trying to free already-free irq"Jeff Kirsher1-1/+1
This reverts commit 7e54d9d063fa239c95c21548c5267f0ef419ff56. After additional regression testing, several users are experiencing kernel panics during shutdown on e1000e devices. Reverting this change resolves the issue. Signed-off-by: Jeff Kirsher <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24kcm: return immediately after copy_from_user() failureWANG Cong1-3/+3
There is no reason to continue after a copy_from_user() failure. Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Cc: Tom Herbert <[email protected]> Signed-off-by: Cong Wang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24bna: avoid writing uninitialized data into hw registersArnd Bergmann1-3/+7
The latest gcc-7 snapshot warns about bfa_ioc_send_enable/bfa_ioc_send_disable writing undefined values into the hardware registers: drivers/net/ethernet/brocade/bna/bfa_ioc.c: In function 'bfa_iocpf_sm_disabling_entry': arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+4)' is used uninitialized in this function [-Werror=uninitialized] arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+8)' is used uninitialized in this function [-Werror=uninitialized] The two functions look like they should do the same thing, but only one of them initializes the time stamp and clscode field. The fact that we only get a warning for one of the two functions seems to be arbitrary, based on the inlining decisions in the compiler. To address this, I'm making both functions do the same thing: - set the clscode from the ioc structure in both - set the time stamp from ktime_get_real_seconds (which also avoids the signed-integer overflow in 2038 and extends the well-defined behavior until 2106). - zero-fill the reserved field Fixes: 8b230ed8ec96 ("bna: Brocade 10Gb Ethernet device driver") Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24Merge branch 's390-net'David S. Miller5-18/+17
Ursula Braun says: ==================== s390/qeth patches for net here are 2 s390/qeth patches built for net fixing a problem with AF_IUCV traffic through HiperSockets. And we come up with an update for the MAINTAINERS file to establish Julian as Co-Maintainer for drivers/s390/net and net/iucv. ==================== Signed-off-by: David S. Miller <[email protected]>
2017-03-24MAINTAINERS: add Julian WiedmannUrsula Braun1-0/+2
Add Julian Wiedmann as additional maintainer for drivers/s390/net and net/iucv. Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24s390/qeth: no ETH header for outbound AF_IUCVJulian Wiedmann1-11/+4
With AF_IUCV traffic, the skb passed to hard_start_xmit() has a 14 byte slot at skb->data, intended for an ETH header. qeth_l3_fill_af_iucv_hdr() fills this ETH header... and then immediately moves it to the skb's headroom, where it disappears and is never seen again. But it's still possible for us to return NETDEV_TX_BUSY after the skb has been modified. Since we didn't get a private copy of the skb, the next time the skb is delivered to hard_start_xmit() it no longer has the expected layout (we moved the ETH header to the headroom, so skb->data now starts at the IUCV_TRANS header). So when qeth_l3_fill_af_iucv_hdr() does another round of rebuilding, the resulting qeth header ends up all wrong. On transmission, the buffer is then rejected by the HiperSockets device with SBALF15 = x'04'. When this error is passed back to af_iucv as TX_NOTIFY_UNREACHABLE, it tears down the offending socket. As the ETH header for AF_IUCV serves no purpose, just align the code to what we do for IP traffic on L3 HiperSockets: keep the ETH header at skb->data, and pass down data_offset = ETH_HLEN to qeth_fill_buffer(). When mapping the payload into the SBAL elements, the ETH header is then stripped off. This avoids the skb manipulations in qeth_l3_fill_af_iucv_hdr(), and any buffer re-entering hard_start_xmit() after NETDEV_TX_BUSY is now processed properly. Signed-off-by: Julian Wiedmann <[email protected]> Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24s390/qeth: size calculation outbound buffersJulian Wiedmann4-7/+11
Depending on the device type, hard_start_xmit() builds different output buffer formats. For instance with HiperSockets, on both L2 and L3 we strip the ETH header from the skb - L3 doesn't need it, and L2 carries it in the buffer's header element. For this, we pass data_offset = ETH_HLEN all the way down to __qeth_fill_buffer(), where skb->data is then adjusted accordingly. But the initial size calculation still considers the *full* skb length (including the ETH header). So qeth_get_elements_no() can erroneously reject a skb as too big, even though it would actually fit into an output buffer once the ETH header has been trimmed off later. Fix this by passing an additional offset to qeth_get_elements_no(), that indicates where in the skb the on-wire data actually begins. Since the current code uses data_offset=-1 for some special handling on OSA, we need to clamp data_offset to 0... On HiperSockets this helps when sending ~MTU-size skbs with weird page alignment. No change for OSA or AF_IUCV. Signed-off-by: Julian Wiedmann <[email protected]> Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24Merge branch 'aquantia-fixes'David S. Miller6-10/+30
Pavel Belous says: ==================== net:ethernet:aquantia: Misc fixes for atlantic driver. The following patchset containg several fixes for aQuantia AQtion driver for net tree: A couple fixes for IPv6 and other fixes. v1->v2: Fix compilation error (using HW_ATL_A0_TXD_CTL_CMD_IPV6 instead HW_ATL_B0_TXD_CTL_CMD_IPV6). v2->v3: Added "Fixes" tags. ==================== Signed-off-by: David S. Miller <[email protected]>
2017-03-24net:ethernet:aquantia: Reset is_gso flag when EOP reached.Pavel Belous2-0/+2
We need to reset is_gso flag when EOP reached (entire LSO packet processed). Fixes: bab6de8fd180 ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.") Signed-off-by: Pavel Belous <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24net:ethernet:aquantia: Fix for LSO with IPv6.Pavel Belous4-1/+11
Fix Context Command bit: L3 type = "0" for IPv4, "1" for IPv6. Fixes: bab6de8fd180 ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.") Signed-off-by: Pavel Belous <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24net:ethernet:aquantia: Missing spinlock initialization.Pavel Belous1-0/+1
Fix for missing initialization aq_ring header.lock spinlock. Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Signed-off-by: Pavel Belous <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24net:ethernet:aquantia: Fix packet type detection (TCP/UDP) for IPv6.Pavel Belous1-4/+16
In order for the checksum offloads to work correctly we need to set the packet type bit (TCP/UDP) in the TX context buffer. Fixes: 97bde5c4f909 ("net: ethernet: aquantia: Support for NIC-specific code") Signed-off-by: Pavel Belous <[email protected]> Tested-by: David Arcari <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24net:ethernet:aquantia: Remove adapter re-opening when MTU changed.Pavel Belous1-5/+0
Closing/opening the adapter is not needed at all. The new MTU settings take effect immediately. Fixes: 97bde5c4f909 ("net: ethernet: aquantia: Support for NIC-specific code") Signed-off-by: Pavel Belous <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24r8152: prevent the driver from transmitting packets with carrier offhayeswang1-2/+16
The linking status may be changed when autosuspend. And, after autoresume, the driver may try to transmit packets when the device is carrier off, because the interrupt transfer doesn't update the linking status, yet. And, if the device is in ALDPS mode, the device would stop working. The another similar case is 1. unplug the cable. 2. interrupt transfer queue a work_queue for linking change. 3. device enters the ALDPS mode. 4. a tx occurs before the work_queue is called. Signed-off-by: Hayes Wang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24net: phy: handle state correctly in phy_stop_machineNathan Sullivan1-1/+1
If the PHY is halted on stop, then do not set the state to PHY_UP. This ensures the phy will be restarted later in phy_start when the machine is started again. Fixes: 00db8189d984 ("This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details.") Signed-off-by: Nathan Sullivan <[email protected]> Signed-off-by: Brad Mouring <[email protected]> Acked-by: Xander Huff <[email protected]> Acked-by: Kyle Roeschley <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-24iwlwifi: mvm: support ibss in dqa modeLiad Kaufman3-6/+13
Allow working IBSS also when working in DQA mode. This is done by setting it to treat the queues the same as a BSS AP treats the queues. Fixes: 7948b87308a4 ("iwlwifi: mvm: enable dynamic queue allocation mode") Signed-off-by: Liad Kaufman <[email protected]> Signed-off-by: Luca Coelho <[email protected]>
2017-03-24iwlwifi: mvm: writing zero bytes to debugfs causes a crashDan Carpenter1-0/+2
This is a static analysis fix. The warning is: drivers/net/wireless/intel/iwlwifi/mvm/fw-dbg.c:912 iwl_mvm_fw_dbg_collect() warn: integer overflows 'sizeof(*desc) + len' I guess this code is supposed to take a NUL character, but if we write zero bytes then it tries to write -1 characters and crashes. Fixes: c91b865cb14d ("iwlwifi: mvm: support description for user triggered fw dbg collection") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Luca Coelho <[email protected]>
2017-03-24iwlwifi: mvm: fix accessing fw_id_to_mac_idSara Sharon1-1/+1
Access should be by rcu_dereference. Issue was found by sparse. Fixes: 65e254821cee ("iwlwifi: mvm: use firmware station PM notification for AP_LINK_PS") Signed-off-by: Sara Sharon <[email protected]> Signed-off-by: Luca Coelho <[email protected]>
2017-03-23net: neigh: guard against NULL solicit() methodEric Dumazet1-1/+2
Dmitry posted a nice reproducer of a bug triggering in neigh_probe() when dereferencing a NULL neigh->ops->solicit method. This can happen for arp_direct_ops/ndisc_direct_ops and similar, which can be used for NUD_NOARP neighbours (created when dev->header_ops is NULL). Admin can then force changing nud_state to some other state that would fire neigh timer. Signed-off-by: Eric Dumazet <[email protected]> Reported-by: Dmitry Vyukov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-23net: phy: Export mdiobus_register_board_info()Florian Fainelli1-0/+1
We can build modular code that uses mdiobus_register_board_info() which would lead to linking failure since this symbol is not expoerted. Fixes: 648ea0134069 ("net: phy: Allow pre-declaration of MDIO devices") Signed-off-by: Florian Fainelli <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-23Merge tag 'sound-4.11-rc4' of ↵Linus Torvalds8-7/+47
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound fixes from Takashi Iwai: "This contains the collection of small fixes for 4.11 that were pending during my vacation: - a few HD-audio quirks (more Dell headset support, docking station support on HP laptops) - a regression fix for the previous ctxfi DMA mask fix - a correction of the new CONFIG_SND_X86 menu entry - a fix for the races in ALSA sequencer core spotted by syzkaller" * tag 'sound-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: hda - Adding a group of pin definition to fix headset problem ALSA: seq: Fix racy cell insertions during snd_seq_pool_done() ALSA: x86: Make CONFIG_SND_X86 bool ALSA: hda - add support for docking station for HP 840 G3 ALSA: hda - add support for docking station for HP 820 G2 ALSA: ctxfi: Fix the incorrect check of dma_set_mask() call
2017-03-23Merge branch 'for-linus-4.11' of ↵Linus Torvalds3-28/+16
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs Pull btrfs fixes from Chris Mason: "Zygo tracked down a very old bug with inline compressed extents. I didn't tag this one for stable because I want to do individual tested backports. It's a little tricky and I'd rather do some extra testing on it along the way" * 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: btrfs: add missing memset while reading compressed inline extents Btrfs: fix regression in lock_delalloc_pages btrfs: remove btrfs_err_str function from uapi/linux/btrfs.h
2017-03-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds100-612/+1086
Pull networking fixes from David Miller: 1) Several netfilter fixes from Pablo and the crew: - Handle fragmented packets properly in netfilter conntrack, from Florian Westphal. - Fix SCTP ICMP packet handling, from Ying Xue. - Fix big-endian bug in nftables, from Liping Zhang. - Fix alignment of fake conntrack entry, from Steven Rostedt. 2) Fix feature flags setting in fjes driver, from Taku Izumi. 3) Openvswitch ipv6 tunnel source address not set properly, from Or Gerlitz. 4) Fix jumbo MTU handling in amd-xgbe driver, from Thomas Lendacky. 5) sk->sk_frag.page not released properly in some cases, from Eric Dumazet. 6) Fix RTNL deadlocks in nl80211, from Johannes Berg. 7) Fix erroneous RTNL lockdep splat in crypto, from Herbert Xu. 8) Cure improper inflight handling during AF_UNIX GC, from Andrey Ulanov. 9) sch_dsmark doesn't write to packet headers properly, from Eric Dumazet. 10) Fix SCM_TIMESTAMPING_OPT_STATS handling in TCP, from Soheil Hassas Yeganeh. 11) Add some IDs for Motorola qmi_wwan chips, from Tony Lindgren. 12) Fix nametbl deadlock in tipc, from Ying Xue. 13) GRO and LRO packets not counted correctly in mlx5 driver, from Gal Pressman. 14) Fix reset of internal PHYs in bcmgenet, from Doug Berger. 15) Fix hashmap allocation handling, from Alexei Starovoitov. 16) nl_fib_input() needs stronger netlink message length checking, from Eric Dumazet. 17) Fix double-free of sk->sk_filter during sock clone, from Daniel Borkmann. 18) Fix RX checksum offloading in aquantia driver, from Pavel Belous. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits) net:ethernet:aquantia: Fix for RX checksum offload. amd-xgbe: Fix the ECC-related bit position definitions sfc: cleanup a condition in efx_udp_tunnel_del() Bluetooth: btqcomsmd: fix compile-test dependency inet: frag: release spinlock before calling icmp_send() tcp: initialize icsk_ack.lrcvtime at session start time genetlink: fix counting regression on ctrl_dumpfamily() socket, bpf: fix sk_filter use after free in sk_clone_lock ipv4: provide stronger user input validation in nl_fib_input() bpf: fix hashmap extra_elems logic enic: update enic maintainers net: bcmgenet: remove bcmgenet_internal_phy_setup() ipv6: make sure to initialize sockc.tsflags before first use fjes: Do not load fjes driver if extended socket device is not power on. fjes: Do not load fjes driver if system does not have extended socket device. net/mlx5e: Count LRO packets correctly net/mlx5e: Count GSO packets correctly net/mlx5: Increase number of max QPs in default profile net/mlx5e: Avoid supporting udp tunnel port ndo for VF reps net/mlx5e: Use the proper UAPI values when offloading TC vlan actions ...
2017-03-23ALSA: hda - Adding a group of pin definition to fix headset problemHui Wang1-0/+2
A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to fix the headset problem, and the pin definiton of this machine is not in the pin quirk table yet, now adding it to the table. Signed-off-by: Hui Wang <[email protected]> Cc: <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2017-03-22net:ethernet:aquantia: Fix for RX checksum offload.Pavel Belous2-0/+2
Since AQC-100/107/108 chips supports hardware checksums for RX we should indicate this via NETIF_F_RXCSUM flag. v1->v2: 'Signed-off-by' tag added. Signed-off-by: Pavel Belous <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22amd-xgbe: Fix the ECC-related bit position definitionsLendacky, Thomas1-12/+12
The ECC bit positions that describe whether the ECC interrupt is for Tx, Rx or descriptor memory and whether the it is a single correctable or double detected error were defined in incorrectly (reversed order). Fix the bit position definitions for these settings so that the proper ECC handling is performed. Signed-off-by: Tom Lendacky <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22sfc: cleanup a condition in efx_udp_tunnel_del()Dan Carpenter1-1/+1
Presumably if there is an "add" function, there is also a "del" function. But it causes a static checker warning because it looks like a common cut and paste bug. Signed-off-by: Dan Carpenter <[email protected]> Acked-by: Jarod Wilson <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22Bluetooth: btqcomsmd: fix compile-test dependencyArnd Bergmann1-1/+2
compile-testing fails when QCOM_SMD is a loadable module: drivers/bluetooth/built-in.o: In function `btqcomsmd_send': btqca.c:(.text+0xa8): undefined reference to `qcom_smd_send' drivers/bluetooth/built-in.o: In function `btqcomsmd_probe': btqca.c:(.text+0x3ec): undefined reference to `qcom_wcnss_open_channel' btqca.c:(.text+0x46c): undefined reference to `qcom_smd_set_drvdata' This clarifies the dependency to allow compile-testing only when SMD is completely disabled, otherwise the dependency on QCOM_SMD will make sure we can link against it. Fixes: e27ee2b16bad ("Bluetooth: btqcomsmd: Allow driver to build if COMPILE_TEST is enabled") Signed-off-by: Arnd Bergmann <[email protected]> [bjorn: Restructure and clarify dependency to QCOM_WCNSS_CTRL] Signed-off-by: Bjorn Andersson <[email protected]> Acked-by: Marcel Holtmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22inet: frag: release spinlock before calling icmp_send()Eric Dumazet1-8/+17
Dmitry reported a lockdep splat [1] (false positive) that we can fix by releasing the spinlock before calling icmp_send() from ip_expire() This is a false positive because sending an ICMP message can not possibly re-enter the IP frag engine. [1] [ INFO: possible circular locking dependency detected ] 4.10.0+ #29 Not tainted ------------------------------------------------------- modprobe/12392 is trying to acquire lock: (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] spin_lock include/linux/spinlock.h:299 [inline] (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] __netif_tx_lock include/linux/netdevice.h:3486 [inline] (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 but task is already holding lock: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock include/linux/spinlock.h:299 [inline] (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&(&q->lock)->rlock){+.-...}: validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] ip_defrag+0x3a2/0x4130 net/ipv4/ip_fragment.c:669 ip_check_defrag+0x4e3/0x8b0 net/ipv4/ip_fragment.c:713 packet_rcv_fanout+0x282/0x800 net/packet/af_packet.c:1459 deliver_skb net/core/dev.c:1834 [inline] dev_queue_xmit_nit+0x294/0xa90 net/core/dev.c:1890 xmit_one net/core/dev.c:2903 [inline] dev_hard_start_xmit+0x16b/0xab0 net/core/dev.c:2923 sch_direct_xmit+0x31f/0x6d0 net/sched/sch_generic.c:182 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_resolve_output+0x6b9/0xb10 net/core/neighbour.c:1308 neigh_output include/net/neighbour.h:478 [inline] ip_finish_output2+0x8b8/0x15a0 net/ipv4/ip_output.c:228 ip_do_fragment+0x1d93/0x2720 net/ipv4/ip_output.c:672 ip_fragment.constprop.54+0x145/0x200 net/ipv4/ip_output.c:545 ip_finish_output+0x82d/0xe10 net/ipv4/ip_output.c:314 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 raw_sendmsg+0x26de/0x3a00 net/ipv4/raw.c:655 inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:761 sock_sendmsg_nosec net/socket.c:633 [inline] sock_sendmsg+0xca/0x110 net/socket.c:643 ___sys_sendmsg+0x4a3/0x9f0 net/socket.c:1985 __sys_sendmmsg+0x25c/0x750 net/socket.c:2075 SYSC_sendmmsg net/socket.c:2106 [inline] SyS_sendmmsg+0x35/0x60 net/socket.c:2101 do_syscall_64+0x2e8/0x930 arch/x86/entry/common.c:281 return_from_SYSCALL_64+0x0/0x7a -> #0 (_xmit_ETHER#2){+.-...}: check_prev_add kernel/locking/lockdep.c:1830 [inline] check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940 validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] __netif_tx_lock include/linux/netdevice.h:3486 [inline] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_hh_output include/net/neighbour.h:468 [inline] neigh_output include/net/neighbour.h:476 [inline] ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228 ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394 icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754 ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239 call_timer_fn+0x241/0x820 kernel/time/timer.c:1268 expire_timers kernel/time/timer.c:1307 [inline] __run_timers+0x960/0xcf0 kernel/time/timer.c:1601 run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614 __do_softirq+0x31f/0xbe7 kernel/softirq.c:284 invoke_softirq kernel/softirq.c:364 [inline] irq_exit+0x1cc/0x200 kernel/softirq.c:405 exiting_irq arch/x86/include/asm/apic.h:657 [inline] smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962 apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707 __read_once_size include/linux/compiler.h:254 [inline] atomic_read arch/x86/include/asm/atomic.h:26 [inline] rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline] __rcu_is_watching kernel/rcu/tree.c:1133 [inline] rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147 rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293 radix_tree_deref_slot include/linux/radix-tree.h:238 [inline] filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335 do_fault_around mm/memory.c:3231 [inline] do_read_fault mm/memory.c:3265 [inline] do_fault+0xbd5/0x2080 mm/memory.c:3370 handle_pte_fault mm/memory.c:3600 [inline] __handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714 handle_mm_fault+0x1e2/0x480 mm/memory.c:3751 __do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397 do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460 page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&(&q->lock)->rlock); lock(_xmit_ETHER#2); lock(&(&q->lock)->rlock); lock(_xmit_ETHER#2); *** DEADLOCK *** 10 locks held by modprobe/12392: #0: (&mm->mmap_sem){++++++}, at: [<ffffffff81329758>] __do_page_fault+0x2b8/0xb60 arch/x86/mm/fault.c:1336 #1: (rcu_read_lock){......}, at: [<ffffffff8188cab6>] filemap_map_pages+0x1e6/0x1570 mm/filemap.c:2324 #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] spin_lock include/linux/spinlock.h:299 [inline] #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] pte_alloc_one_map mm/memory.c:2944 [inline] #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] alloc_set_pte+0x13b8/0x1b90 mm/memory.c:3072 #3: (((&q->timer))){+.-...}, at: [<ffffffff81627e72>] lockdep_copy_map include/linux/lockdep.h:175 [inline] #3: (((&q->timer))){+.-...}, at: [<ffffffff81627e72>] call_timer_fn+0x1c2/0x820 kernel/time/timer.c:1258 #4: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock include/linux/spinlock.h:299 [inline] #4: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201 #5: (rcu_read_lock){......}, at: [<ffffffff8389a633>] ip_expire+0x1b3/0x6c0 net/ipv4/ip_fragment.c:216 #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] spin_trylock include/linux/spinlock.h:309 [inline] #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] icmp_xmit_lock net/ipv4/icmp.c:219 [inline] #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] icmp_send+0x803/0x1c80 net/ipv4/icmp.c:681 #7: (rcu_read_lock_bh){......}, at: [<ffffffff838ab9a1>] ip_finish_output2+0x2c1/0x15a0 net/ipv4/ip_output.c:198 #8: (rcu_read_lock_bh){......}, at: [<ffffffff836d1dee>] __dev_queue_xmit+0x23e/0x1e60 net/core/dev.c:3324 #9: (dev->qdisc_running_key ?: &qdisc_running_key){+.....}, at: [<ffffffff836d3a27>] dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 stack backtrace: CPU: 0 PID: 12392 Comm: modprobe Not tainted 4.10.0+ #29 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:16 [inline] dump_stack+0x2ee/0x3ef lib/dump_stack.c:52 print_circular_bug+0x307/0x3b0 kernel/locking/lockdep.c:1204 check_prev_add kernel/locking/lockdep.c:1830 [inline] check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940 validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] __netif_tx_lock include/linux/netdevice.h:3486 [inline] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_hh_output include/net/neighbour.h:468 [inline] neigh_output include/net/neighbour.h:476 [inline] ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228 ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394 icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754 ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239 call_timer_fn+0x241/0x820 kernel/time/timer.c:1268 expire_timers kernel/time/timer.c:1307 [inline] __run_timers+0x960/0xcf0 kernel/time/timer.c:1601 run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614 __do_softirq+0x31f/0xbe7 kernel/softirq.c:284 invoke_softirq kernel/softirq.c:364 [inline] irq_exit+0x1cc/0x200 kernel/softirq.c:405 exiting_irq arch/x86/include/asm/apic.h:657 [inline] smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962 apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707 RIP: 0010:__read_once_size include/linux/compiler.h:254 [inline] RIP: 0010:atomic_read arch/x86/include/asm/atomic.h:26 [inline] RIP: 0010:rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline] RIP: 0010:__rcu_is_watching kernel/rcu/tree.c:1133 [inline] RIP: 0010:rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147 RSP: 0000:ffff8801c391f120 EFLAGS: 00000a03 ORIG_RAX: ffffffffffffff10 RAX: dffffc0000000000 RBX: ffff8801c391f148 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 000055edd4374000 RDI: ffff8801dbe1ae0c RBP: ffff8801c391f1a0 R08: 0000000000000002 R09: 0000000000000000 R10: dffffc0000000000 R11: 0000000000000002 R12: 1ffff10038723e25 R13: ffff8801dbe1ae00 R14: ffff8801c391f680 R15: dffffc0000000000 </IRQ> rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293 radix_tree_deref_slot include/linux/radix-tree.h:238 [inline] filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335 do_fault_around mm/memory.c:3231 [inline] do_read_fault mm/memory.c:3265 [inline] do_fault+0xbd5/0x2080 mm/memory.c:3370 handle_pte_fault mm/memory.c:3600 [inline] __handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714 handle_mm_fault+0x1e2/0x480 mm/memory.c:3751 __do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397 do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460 page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011 RIP: 0033:0x7f83172f2786 RSP: 002b:00007fffe859ae80 EFLAGS: 00010293 RAX: 000055edd4373040 RBX: 00007f83175111c8 RCX: 000055edd4373238 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00007f8317510970 RBP: 00007fffe859afd0 R08: 0000000000000009 R09: 0000000000000000 R10: 0000000000000064 R11: 0000000000000000 R12: 000055edd4373040 R13: 0000000000000000 R14: 00007fffe859afe8 R15: 0000000000000000 Signed-off-by: Eric Dumazet <[email protected]> Reported-by: Dmitry Vyukov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22tcp: initialize icsk_ack.lrcvtime at session start timeEric Dumazet2-1/+2
icsk_ack.lrcvtime has a 0 value at socket creation time. tcpi_last_data_recv can have bogus value if no payload is ever received. This patch initializes icsk_ack.lrcvtime for active sessions in tcp_finish_connect(), and for passive sessions in tcp_create_openreq_child() Signed-off-by: Eric Dumazet <[email protected]> Acked-by: Neal Cardwell <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22genetlink: fix counting regression on ctrl_dumpfamily()Stanislaw Gruszka1-1/+3
Commit 2ae0f17df1cd ("genetlink: use idr to track families") replaced if (++n < fams_to_skip) continue; into: if (n++ < fams_to_skip) continue; This subtle change cause that on retry ctrl_dumpfamily() call we omit one family that failed to do ctrl_fill_info() on previous call, because cb->args[0] = n number counts also family that failed to do ctrl_fill_info(). Patch fixes the problem and avoid confusion in the future just decrease n counter when ctrl_fill_info() fail. User visible problem caused by this bug is failure to get access to some genetlink family i.e. nl80211. However problem is reproducible only if number of registered genetlink families is big enough to cause second call of ctrl_dumpfamily(). Cc: Xose Vazquez Perez <[email protected]> Cc: Larry Finger <[email protected]> Cc: Johannes Berg <[email protected]> Fixes: 2ae0f17df1cd ("genetlink: use idr to track families") Signed-off-by: Stanislaw Gruszka <[email protected]> Acked-by: Johannes Berg <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22socket, bpf: fix sk_filter use after free in sk_clone_lockDaniel Borkmann1-0/+6
In sk_clone_lock(), we create a new socket and inherit most of the parent's members via sock_copy() which memcpy()'s various sections. Now, in case the parent socket had a BPF socket filter attached, then newsk->sk_filter points to the same instance as the original sk->sk_filter. sk_filter_charge() is then called on the newsk->sk_filter to take a reference and should that fail due to hitting max optmem, we bail out and release the newsk instance. The issue is that commit 278571baca2a ("net: filter: simplify socket charging") wrongly combined the dismantle path with the failure path of xfrm_sk_clone_policy(). This means, even when charging failed, we call sk_free_unlock_clone() on the newsk, which then still points to the same sk_filter as the original sk. Thus, sk_free_unlock_clone() calls into __sk_destruct() eventually where it tests for present sk_filter and calls sk_filter_uncharge() on it, which potentially lets sk_omem_alloc wrap around and releases the eBPF prog and sk_filter structure from the (still intact) parent. Fix it by making sure that when sk_filter_charge() failed, we reset newsk->sk_filter back to NULL before passing to sk_free_unlock_clone(), so that we don't mess with the parents sk_filter. Only if xfrm_sk_clone_policy() fails, we did reach the point where either the parent's filter was NULL and as a result newsk's as well or where we previously had a successful sk_filter_charge(), thus for that case, we do need sk_filter_uncharge() to release the prior taken reference on sk_filter. Fixes: 278571baca2a ("net: filter: simplify socket charging") Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Alexei Starovoitov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2017-03-22ipv4: provide stronger user input validation in nl_fib_input()Eric Dumazet1-1/+2
Alexander reported a KMSAN splat caused by reads of uninitialized field (tb_id_in) from user provided struct fib_result_nl It turns out nl_fib_input() sanity tests on user input is a bit wrong : User can pretend nlh->nlmsg_len is big enough, but provide at sendmsg() time a too small buffer. Reported-by: Alexander Potapenko <[email protected]> Signed-off-by: Eric Dumazet <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.