aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2016-04-13usb: host: xhci-plat: Make enum xhci_plat_type start at a non zero valuePeter Griffin1-1/+1
Otherwise generic-xhci and xhci-platform which have no data get wrongly detected as XHCI_PLAT_TYPE_MARVELL_ARMADA by xhci_plat_type_is(). This fixes a regression in v4.5 for STiH407 family SoC's which use the synopsis dwc3 IP, whereby the disable_clk error path gets taken due to wrongly being detected as XHCI_PLAT_TYPE_MARVELL_ARMADA and the hcd never gets added. I suspect this will also fix other dwc3 DT platforms such as Exynos, although I've only tested on STih410 SoC. Fixes: 4efb2f694114 ("usb: host: xhci-plat: add struct xhci_plat_priv") Cc: [email protected] Cc: [email protected] Cc: [email protected] Signed-off-by: Peter Griffin <[email protected]> Signed-off-by: Mathias Nyman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2016-04-13xhci: fix 10 second timeout on removal of PCI hotpluggable xhci controllersMathias Nyman4-4/+9
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will remove the xhci controller from the PCI bus when the last USB device is disconnected. Add a flag to indicate that the host is being removed to avoid queueing configure_endpoint commands for the dropped endpoints. For PCI hotplugged controllers this will prevent 5 second command timeouts For static xhci controllers the configure_endpoint command is not needed in the removal case as everything will be returned, freed, and the controller is reset. For now the flag is only set for PCI connected host controllers. Cc: <[email protected]> Signed-off-by: Mathias Nyman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2016-04-13usb: xhci: fix wild pointers in xhci_mem_cleanupLu Baolu1-0/+6
This patch fixes some wild pointers produced by xhci_mem_cleanup. These wild pointers will cause system crash if xhci_mem_cleanup() is called twice. Reported-and-tested-by: Pengcheng Li <[email protected]> Signed-off-by: Lu Baolu <[email protected]> Cc: [email protected] Signed-off-by: Mathias Nyman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2016-04-13usb: host: xhci-plat: fix cannot work if R-Car Gen2/3 run on above 4GB physYoshihiro Shimoda1-0/+13
This patch fixes an issue that cannot work if R-Car Gen2/3 run on above 4GB physical memory environment to use a quirk XHCI_NO_64BIT_SUPPORT. Cc: <[email protected]> Signed-off-by: Yoshihiro Shimoda <[email protected]> Reviewed-by: Felipe Balbi <[email protected]> Signed-off-by: Mathias Nyman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2016-04-13usb: host: xhci: add a new quirk XHCI_NO_64BIT_SUPPORTYoshihiro Shimoda2-0/+11
On some xHCI controllers (e.g. R-Car SoCs), the AC64 bit (bit 0) of HCCPARAMS1 is set to 1. However, the xHCs don't support 64-bit address memory pointers actually. So, in this case, this driver should call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in xhci_gen_setup(). Otherwise, the xHCI controller will be died after a usb device is connected if it runs on above 4GB physical memory environment. So, this patch adds a new quirk XHCI_NO_64BIT_SUPPORT to resolve such an issue. Cc: <[email protected]> Signed-off-by: Yoshihiro Shimoda <[email protected]> Reviewed-by: Felipe Balbi <[email protected]> Signed-off-by: Mathias Nyman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2016-04-13xhci: resume USB 3 roothub firstMathias Nyman1-3/+3
Give USB3 devices a better chance to enumerate at USB 3 speeds if they are connected to a suspended host. Solves an issue with NEC uPD720200 host hanging when partially enumerating a USB3 device as USB2 after host controller runtime resume. Cc: <[email protected]> Tested-by: Mike Murdoch <[email protected]> Signed-off-by: Mathias Nyman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2016-04-13usb: xhci: applying XHCI_PME_STUCK_QUIRK to Intel BXT B0 hostRafal Redzimski1-1/+3
Broxton B0 also requires XHCI_PME_STUCK_QUIRK. Adding PCI device ID for Broxton B and adding to quirk. Cc: <[email protected]> Signed-off-by: Rafal Redzimski <[email protected]> Signed-off-by: Robert Dobrowolski <[email protected]> Signed-off-by: Mathias Nyman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2016-04-13cdc-acm: fix crash if flushed with nothing bufferedOliver Neukum1-0/+4
Under some circumstances acm_tty_flush_chars() is called with no buffer to flush. We simply need to do nothing. Signed-off-by: Oliver Neukum <[email protected]> Reported-by: Torsten Hilbrich <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2016-04-13lib: lz4: cleanup unaligned access efficiency detectionRui Salvaterra1-3/+1
These identifiers are bogus. The interested architectures should define HAVE_EFFICIENT_UNALIGNED_ACCESS whenever relevant to do so. If this isn't true for some arch, it should be fixed in the arch definition. Signed-off-by: Rui Salvaterra <[email protected]> Reviewed-by: Sergey Senozhatsky <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2016-04-13lib: lz4: fixed zram with lz4 on big endian machinesRui Salvaterra1-9/+12
Based on Sergey's test patch [1], this fixes zram with lz4 compression on big endian cpus. Note that the 64-bit preprocessor test is not a cleanup, it's part of the fix, since those identifiers are bogus (for example, __ppc64__ isn't defined anywhere else in the kernel, which means we'd fall into the 32-bit definitions on ppc64). Tested on ppc64 with no regression on x86_64. [1] http://marc.info/?l=linux-kernel&m=145994470805853&w=4 Cc: [email protected] Suggested-by: Sergey Senozhatsky <[email protected]> Signed-off-by: Rui Salvaterra <[email protected]> Reviewed-by: Sergey Senozhatsky <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2016-04-13dmaengine: dw: fix master selectionAndy Shevchenko1-15/+19
The commit 895005202987 ("dmaengine: dw: apply both HS interfaces and remove slave_id usage") cleaned up the code to avoid usage of depricated slave_id member of generic slave configuration. Meanwhile it broke the master selection by removing important call to dwc_set_masters() in ->device_alloc_chan_resources() which copied masters from custom slave configuration to the internal channel structure. Everything works until now since there is no customized connection of DesignWare DMA IP to the bus, i.e. one bus and one or more masters are in use. The configurations where 2 masters are connected to the different masters are not working anymore. We are expecting one user of such configuration and need to select masters properly. Besides that it is obviously a performance regression since only one master is in use in multi-master configuration. Select masters in accordance with what user asked for. Keep this patch in a form more suitable for back porting. We are safe to take necessary data in ->device_alloc_chan_resources() because we don't support generic slave configuration embedded into custom one, and thus the only way to provide such is to use the parameter to a filter function which is called exactly before channel resource allocation. While here, replase BUG_ON to less noisy dev_warn() and prevent channel allocation in case of error. Fixes: 895005202987 ("dmaengine: dw: apply both HS interfaces and remove slave_id usage") Cc: [email protected] Signed-off-by: Andy Shevchenko <[email protected]> Signed-off-by: Vinod Koul <[email protected]>
2016-04-13Merge branch 'for-linus' of ↵Linus Torvalds1-7/+1
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu Pull m68knommu/coldfire fix from Greg Ungerer: "Only a single change that removes a local arch specific gpio bus sysfs device that now clashes with the generic gpio bus sysfs device interface" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: m68k/gpio: remove arch specific sysfs bus device
2016-04-13Merge tag 'armsoc-fixes' of ↵Linus Torvalds20-85/+89
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Olof Johansson: "A batch of fixes for -rc4, for various platforms. Nothing really substantial and worth pointing out in particular; small fixes for various bugs, see shortlog for details" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: sa1100: remove references to the defunct handhelds.org bus: uniphier-system-bus: fix condition of overlap check ARM: uniphier: drop weird sizeof() ARM: dts: am335x-baltos-ir5221: fix cpsw_emac0 link type ARM: OMAP: Correct interrupt type for ARM TWD ARM: DRA722: Add ID detect for Silicon Rev 2.0 ARM: dts: am43xx: fix edma memcpy channel allocation ARM: dts: AM43x-epos: Fix clk parent for synctimer ARM: OMAP2: Fix up interconnect barrier initialization for DRA7 documentation: Fix pinctrl documentation for Meson8 / Meson8b ARM: dts: amlogic: Split pinctrl device for Meson8 / Meson8b ARM: mvebu: Correct unit address for linksys bus: mvebu-mbus: use %pa to print phys_addr_t arm64: dts: vulcan: Update PCI ranges ARM: u8500_defconfig: turn on the Synaptics RMI4 driver ARM: pxa: fix the number of DMA requestor lines ARM: OMAP2+: hwmod: Fix updating of sysconfig register ARM: OMAP2+: Use srst_udelay for USB on dm814x
2016-04-13Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds12-37/+106
Pull KVM fixes from Radim Krčmář: "ARM fixes: - Wrong indentation in the PMU code from the merge window - A long-time bug occuring with running ntpd on the host, candidate for stable - Properly handle (and warn about) the unsupported configuration of running on systems with less than 40 bits of PA space - More fixes to the PM and hotplug notifier stuff from the merge window x86: - leak of guest xcr0 (typically shows up as SIGILL) - new maintainer (who is sending the pull request too) - fix for merge window regression - fix for guest CPUID" Paolo Bonzini points out: "For the record, this tag is signed by me because I prepared the pull request. Further pull requests for 4.6 will be signed and sent out by Radim directly" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: mask CPUID(0xD,0x1).EAX against host value kvm: x86: do not leak guest xcr0 into host interrupt handlers KVM: MMU: fix permission_fault() KVM: new maintainer on the block arm64: KVM: unregister notifiers in hyp mode teardown path arm64: KVM: Warn when PARange is less than 40 bits KVM: arm/arm64: Handle forward time correction gracefully arm64: KVM: Add braces to multi-line if statement in virtual PMU code
2016-04-13x86/mce: Avoid using object after free in genpoolTony Luck1-2/+2
When we loop over all queued machine check error records to pass them to the registered notifiers we use llist_for_each_entry(). But the loop calls gen_pool_free() for the entry in the body of the loop - and then the iterator looks at node->next after the free. Use llist_for_each_entry_safe() instead. Signed-off-by: Tony Luck <[email protected]> Signed-off-by: Borislav Petkov <[email protected]> Cc: <[email protected]> Cc: Gong Chen <[email protected]> Cc: Linus Torvalds <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Thomas Gleixner <[email protected]> Cc: linux-edac <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Ingo Molnar <[email protected]>
2016-04-13ALSA: hda - Fix inconsistent monitor_present state until repollTakashi Iwai1-7/+4
While the previous commit fixed the missing monitor_present flag update, it may be still in an inconsistent state while the driver repolls: the flag itself is updated, but the eld_valid flag and the contents don't follow until the repoll finishes (and may be repeated for a few times). The basic problem is that pin_eld->monitor_present is updated in the caller side. This should have been updated only in update_eld(). So, the proper fix is to avoid accessing pin_eld but only spec->temp_eld. Signed-off-by: Takashi Iwai <[email protected]>
2016-04-13ALSA: hda - Fix regression of monitor_present flag in eld proc fileHyungwon Hwang1-0/+2
The commit [bd48128539ab: ALSA: hda - Fix forgotten HDMI monitor_present update] covered the missing update of monitor_present flag, but this caused a regression for devices without the i915 eld notifier. Since the old code supposed that pin_eld->monitor_present was updated by the caller side, the hdmi_present_sense_via_verbs() doesn't update the temporary eld->monitor_present but only pin_eld->monitor_present, which is now overridden in update_eld(). The fix is to update pin_eld->monitor_present as well before calling update_eld(). Note that this may still leave monitor_present flag in an inconsistent state when the driver repolls, but this is at least the old behavior. More proper fix will follow in the later patch. Fixes: bd48128539ab ('ALSA: hda - Fix forgotten HDMI monitor_present update') Signed-off-by: Hyungwon Hwang <[email protected]> Cc: <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2016-04-12ext4/fscrypto: avoid RCU lookup in d_revalidateJaegeuk Kim2-0/+8
As Al pointed, d_revalidate should return RCU lookup before using d_inode. This was originally introduced by: commit 34286d666230 ("fs: rcu-walk aware d_revalidate method"). Reported-by: Al Viro <[email protected]> Signed-off-by: Jaegeuk Kim <[email protected]> Cc: Theodore Ts'o <[email protected]> Cc: stable <[email protected]>
2016-04-13Merge tag 'keys-fixes-20160412' of ↵James Morris2-2/+4
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs into for-linus
2016-04-12debugfs: Make automount point inodes permanently emptySeth Forshee1-1/+1
Starting with 4.1 the tracing subsystem has its own filesystem which is automounted in the tracing subdirectory of debugfs. Prior to this debugfs could be bind mounted in a cloned mount namespace, but if tracefs has been mounted under debugfs this now fails because there is a locked child mount. This creates a regression for container software which bind mounts debugfs to satisfy the assumption of some userspace software. In other pseudo filesystems such as proc and sysfs we're already creating mountpoints like this in such a way that no dirents can be created in the directories, allowing them to be exceptions to some MNT_LOCKED tests. In fact we're already do this for the tracefs mountpoint in sysfs. Do the same in debugfs_create_automount(), since the intention here is clearly to create a mountpoint. This fixes the regression, as locked child mounts on permanently empty directories do not cause a bind mount to fail. Cc: [email protected] # v4.1+ Signed-off-by: Seth Forshee <[email protected]> Acked-by: Serge Hallyn <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2016-04-12Merge tag 'mvebu-fixes-4.6-1' of git://git.infradead.org/linux-mvebu into fixesOlof Johansson2-2/+2
mvebu fixes for 4.6 (part 1) - fix USB adress register for Linksys Armada 388 based boards - fix build warning in mvebu-mbus * tag 'mvebu-fixes-4.6-1' of git://git.infradead.org/linux-mvebu: ARM: mvebu: Correct unit address for linksys bus: mvebu-mbus: use %pa to print phys_addr_t Signed-off-by: Olof Johansson <[email protected]>
2016-04-12ARM: sa1100: remove references to the defunct handhelds.orgLinus Walleij1-8/+2
The website handhelds.org has been down for a long time and is likely never coming back online. Signed-off-by: Linus Walleij <[email protected]> Signed-off-by: Olof Johansson <[email protected]>
2016-04-12Merge tag 'pxa-fixes-v4.6' of https://github.com/rjarzmik/linux into fixesOlof Johansson1-0/+1
ARM: pxa: fixes for v4.6 There is only a single fix for dma requestor lines initial setup, triggered by dmaengine previous fix. * tag 'pxa-fixes-v4.6' of https://github.com/rjarzmik/linux: ARM: pxa: fix the number of DMA requestor lines Signed-off-by: Olof Johansson <[email protected]>
2016-04-12Merge tag 'omap-for-v4.6/fixes-rc1' of ↵Olof Johansson9-9/+21
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes Fixes for omaps against v4.6-rc1. Mostly minor fixes for the newer SoCs with few board fixes and a fix for a long time hwmod bug: - Fix cpsw_emac0 link type for baltos-ir5221 - Fix interrupt type for TWD - Fix edma memcpy channel allocation for am43x - Fix am43x-epos sycntimer32k by using the correct assigned clock - Fix interconnect barrier for dra7 - Fix a long time hwmod bug for updating sysconfig register properly - Fix flakey booting on dm814x where USB reset needs a delay And there is one minor change that is not strictly a fix, but is good to have for proper hardware detection: - Detect dra7 silicon revision 2.0 properly * tag 'omap-for-v4.6/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: am335x-baltos-ir5221: fix cpsw_emac0 link type ARM: OMAP: Correct interrupt type for ARM TWD ARM: DRA722: Add ID detect for Silicon Rev 2.0 ARM: dts: am43xx: fix edma memcpy channel allocation ARM: dts: AM43x-epos: Fix clk parent for synctimer ARM: OMAP2: Fix up interconnect barrier initialization for DRA7 ARM: OMAP2+: hwmod: Fix updating of sysconfig register ARM: OMAP2+: Use srst_udelay for USB on dm814x Signed-off-by: Olof Johansson <[email protected]>
2016-04-12bus: uniphier-system-bus: fix condition of overlap checkKunihiko Hayashi1-1/+1
This patch fixes condition whether the specified address ranges overlap each other. Fixes: 4b7f48d395a7 ("bus: uniphier-system-bus: add UniPhier System Bus driver") Signed-off-by: Kunihiko Hayashi <[email protected]> Acked-by: Masahiro Yamada <[email protected]> Signed-off-by: Olof Johansson <[email protected]>
2016-04-12ARM: uniphier: drop weird sizeof()Masahiro Yamada1-1/+1
My intention was to ioremap a 4-byte register. Coincidentally enough, sizeof(SZ_4) equals to SZ_4, but this code is weird anyway. Signed-off-by: Masahiro Yamada <[email protected]> Signed-off-by: Olof Johansson <[email protected]>
2016-04-12fscrypto: don't let data integrity writebacks fail with ENOMEMJaegeuk Kim3-23/+38
This patch fixes the issue introduced by the ext4 crypto fix in a same manner. For F2FS, however, we flush the pending IOs and wait for a while to acquire free memory. Fixes: c9af28fdd4492 ("ext4 crypto: don't let data integrity writebacks fail with ENOMEM") Cc: Theodore Ts'o <[email protected]> Signed-off-by: Jaegeuk Kim <[email protected]>
2016-04-12f2fs: use dget_parent and file_dentry in f2fs_file_openJaegeuk Kim1-3/+7
This patch synced with the below two ext4 crypto fixes together. In 4.6-rc1, f2fs newly introduced accessing f_path.dentry which crashes overlayfs. To fix, now we need to use file_dentry() to access that field. Fixes: c0a37d487884 ("ext4: use file_dentry()") Fixes: 9dd78d8c9a7b ("ext4: use dget_parent() in ext4_file_open()") Cc: Miklos Szeredi <[email protected]> Cc: Theodore Ts'o <[email protected]> Signed-off-by: Jaegeuk Kim <[email protected]>
2016-04-12fscrypto: use dget_parent() in fscrypt_d_revalidate()Jaegeuk Kim1-3/+8
This patch updates fscrypto along with the below ext4 crypto change. Fixes: 3d43bcfef5f0 ("ext4 crypto: use dget_parent() in ext4_d_revalidate()") Cc: Theodore Ts'o <[email protected]> Signed-off-by: Jaegeuk Kim <[email protected]>
2016-04-13drm/exynos: Use VIDEO_SAMSUNG_S5P_G2D=n as G2D Kconfig dependencyJavier Martinez Canillas1-1/+1
Commit 254d4d111ee1 ("drm/exynos: Add dependency for G2D in Kconfig") made the DRM_EXYNOS_G2D symbol to only be selectable if the s5p-g2d V4L2 driver is not enabled, since both use the same HW IP block. But added the dependency as depends on !VIDEO_SAMSUNG_S5P_G2D which isn't correct since Kconfig expressions are not boolean but tristate. So it will only evaluate to 'n' if VIDEO_SAMSUNG_S5P_G2D=y but it will evaluate to m if VIDEO_SAMSUNG_S5P_G2D=m. This means that both the V4L2 and DRM drivers can be enabled if the former is enabled as a module, which is not what we want. Signed-off-by: Javier Martinez Canillas <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2016-04-12drm/exynos: fix a warning messageDan Carpenter1-1/+1
The "ret = regmap_write()" assignment was missing so this error message is never printed. Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2016-04-12drm/exynos: mic: fix an error codeDan Carpenter1-0/+1
We accidentally return success instead of a negative error code here. Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2016-04-12drm/exynos: fimd: fix broken dp_clock controlMarek Szyprowski1-1/+1
Commit 1feafd3afd294b03dbbedb8e8f94e0c4db526f10 ("drm/exynos: add exynos5420 support for fimd") add support for Exynos 5420 SoC, but it broke enabling display clock feature because of incorrect condition check. This patch fixes it, so display is working again on platforms requiring display clock control (i.e. Exynos5250-based SNOW platform). Signed-off-by: Marek Szyprowski <[email protected]> Reviewed-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2016-04-12drm/exynos: build fbdev code conditionallyAndrzej Hajda4-15/+36
Fbdev code should be compiled only if CONFIG_DRM_FBDEV_EMULATION option is enabled. The patch fixes exynos-drm code trying to manipulate fbdev data which is not initialized in case CONFIG_DRM_FBDEV_EMULATION is disabled. Signed-off-by: Andrzej Hajda <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2016-04-12drm/exynos: fix adjusted_mode pointer in exynos_plane_mode_setAndrzej Hajda1-5/+7
exynos_plane_mode_set should use adjusted_mode from the same atomic state as plane state. Otherwise it will result in incorrect behavior in case crtc mode changes. The patch fixes bug with black console framebuffer in case of command mode panels. Signed-off-by: Andrzej Hajda <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2016-04-12drm/exynos: fix error handling in exynos_drm_subdrv_openArnd Bergmann1-1/+1
gcc-6 warns about a pointless loop in exynos_drm_subdrv_open: drivers/gpu/drm/exynos/exynos_drm_core.c: In function 'exynos_drm_subdrv_open': drivers/gpu/drm/exynos/exynos_drm_core.c:104:199: error: self-comparison always evaluates to false [-Werror=tautological-compare] list_for_each_entry_reverse(subdrv, &subdrv->list, list) { Here, the list_for_each_entry_reverse immediately terminates because the subdrv pointer is compared to itself as the loop end condition. If we were to take the current subdrv pointer as the start of the list (as we would do if list_for_each_entry_reverse() was not a macro), we would iterate backwards over the &exynos_drm_subdrv_list anchor, which would be even worse. Instead, we need to use list_for_each_entry_continue_reverse() to go back over each subdrv that was successfully opened until the first entry. Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2016-04-12ALSA: usb-audio: Skip volume controls triggers hangup on Dell USB DockKailang Yang1-0/+14
This is Dell usb dock audio workaround. It was fixed the master volume keep lower. [Some background: the patch essentially skips the controls of a couple of FU volumes. Although the firmware exposes the dB and the value information via the usb descriptor, changing the values (we set the min volume as default) screws up the device. Although this has been fixed in the newer firmware, the devices are shipped with the old firmware, thus we need the workaround in the driver side. -- tiwai] Signed-off-by: Kailang Yang <[email protected]> Cc: <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2016-04-12mailbox: Stop using ENOSYS for anything other than unimplemented syscallsLee Jones1-2/+2
In accordance with e15f431fe2d5 ("errno.h: Improve ENOSYS's comment") and 91c9afaf97ee ("checkpatch.pl: new instances of ENOSYS are errors") we're converting from the old meaning of: ENOSYS "Function not implemented" to a more standard EINVAL. Reported-by: Seraphin Bonnaffe <[email protected]> Signed-off-by: Lee Jones <[email protected]> Signed-off-by: Jassi Brar <[email protected]>
2016-04-12mailbox: mailbox-test: Prevent memory leakLee Jones1-3/+6
If we set the Signal twice or more, without using it as part of a message, memory will be re-allocated and the pointer over-written. Prevent this potential leak by only allocating memory when there isn't any already. Reported-by: Dan Carpenter <[email protected]> Signed-off-by: Lee Jones <[email protected]> Signed-off-by: Jassi Brar <[email protected]>
2016-04-12mailbox: mailbox-test: Use more consistent format for calling copy_from_user()Lee Jones1-4/+3
While we're at it, ensure copy-to location is NULL'ed in the error path. Suggested-by: Dan Carpenter <[email protected]> Signed-off-by: Lee Jones <[email protected]> Signed-off-by: Jassi Brar <[email protected]>
2016-04-11Merge branch 'for-linus' of ↵Linus Torvalds10-73/+164
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid Pull HID fixes from Jiri Kosina: - fix for how scaling linearization is computed in wiimote driver, by Cyan Ogilvie - endless retry loop fix in generic USB HID core reset-resume handling, by Alan Stern - two functional fixes affecting particular devices, and oops fix for wacom driver, by Jason Gerecke - multitouch slot numbering fix from Gabriele Mazzotta - a couple more small fixes on top * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: wacom: Support switching from vendor-defined device mode on G9 and G11 HID: wacom: Initialize hid_data.inputmode to -1 HID: microsoft: add support for 3 more devices HID: multitouch: Synchronize MT frame on reset_resume HID: wacom: fix Bamboo ONE oops HID: lenovo: Don't use stack variables for DMA buffers HID: usbhid: fix inconsistent reset/resume/reset-resume behavior HID: wiimote: Fix wiimote mp scale linearization
2016-04-11Merge branch 'for-linus' of ↵Linus Torvalds15-85/+77
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k Pull m68k update from Geert Uytterhoeven. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: m68k/defconfig: Update defconfigs for v4.6-rc2 m68k: Wire up preadv2 and pwritev2
2016-04-11Merge tag 'arc-4.6-rc4-fixes' of ↵Linus Torvalds5-9/+21
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc Pull ARC fixes from Vineet Gupta: - fix Kconfig splat due to pcie rework - make ethernet work again on axs103 - provide fb_pgprotect() for future video driver integration * tag 'arc-4.6-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: ARC: [plat-axs103] Enable loop block devices Revert "ARC: [plat-axs10x] add Ethernet PHY description in .dts" arc: Add our own implementation of fb_pgprotect() ARC: Don't source drivers/pci/pcie/Kconfig ourselves
2016-04-11NVMe: Fix reset/remove raceKeith Busch1-2/+4
This fixes a scenario where device is present and being reset, but a request to unbind the driver occurs. A previous patch series addressing a device failure removal scenario flushed reset_work after controller disable to unblock reset_work waiting on a completion that wouldn't occur. This isn't safe as-is. The broken scenario can potentially be induced with: modprobe nvme && modprobe -r nvme To fix, the reset work is flushed immediately after setting the controller removing flag, and any subsequent reset will not proceed with controller initialization if the flag is set. The controller status must be polled while active, so the watchdog timer is also left active until the controller is disabled to cleanup requests that may be stuck during namespace removal. [Fixes: ff23a2a15a2117245b4599c1352343c8b8fb4c43] Signed-off-by: Keith Busch <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Reviewed-by: Johannes Thumshirn <[email protected]> Reviewed-by: Sagi Grimberg <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2016-04-11dm: fix dm_target_io leak if clone_bio() returns an errorMikulas Patocka1-1/+3
Commit c80914e81ec5b08 ("dm: return error if bio_integrity_clone() fails in clone_bio()") changed clone_bio() such that if it does return error then the alloc_tio() created resources (both the bio that was allocated to be a clone and the containing dm_target_io struct) will leak. Fix this by calling free_tio() in __clone_and_map_data_bio()'s clone_bio() error path. Fixes: c80914e81ec5b08 ("dm: return error if bio_integrity_clone() fails in clone_bio()") Signed-off-by: Mikulas Patocka <[email protected]> Signed-off-by: Mike Snitzer <[email protected]>
2016-04-11ALSA: hda/realtek - Enable the ALC292 dock fixup on the Thinkpad T460sSven Eckelmann1-1/+9
The Lenovo Thinkpad T460s requires the alc_fixup_tpt440_dock as well in order to get working sound output on the docking stations headphone jack. Patch tested on a Thinkpad T460s (20F9CT01WW) using a ThinkPad Ultradock on kernel 4.4.6. Signed-off-by: Sven Eckelmann <[email protected]> Tested-by: Simon Wunderlich <[email protected]> Cc: <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2016-04-11ALSA: sscape: Use correct format identifier for size_tWilliam Breathitt Gray1-1/+1
The 'size' member of a struct firmware is passed to snd_printk with a respective format string using the %d identifier. The 'size' member is of type size_t, but format identifier %d indicates a signed int data type. This patch replaces the %d format identifier with the correct %zu format identifier for size_t data types. Signed-off-by: William Breathitt Gray <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2016-04-11Merge tag 'drm-intel-fixes-2016-04-07' of ↵Dave Airlie4-12/+7
git://anongit.freedesktop.org/drm-intel into drm-fixes misc i915 fixes. * tag 'drm-intel-fixes-2016-04-07' of git://anongit.freedesktop.org/drm-intel: drm/i915: fix deadlock on lid open drm/i915: Exit cherryview_irq_handler() after one pass drm/i915: Call intel_dp_mst_resume() before resuming displays drm/i915: Fix race condition in intel_dp_destroy_mst_connector()
2016-04-11Merge tag 'topic/drm-fixes-2016-04-07' of ↵Dave Airlie3-9/+16
git://anongit.freedesktop.org/drm-intel into drm-fixes The qxl fix I've picked up quite some time ago, and unfortunately neglected. Then there's established timing fixes, of which particularly "drm/edid: Fix parsing of EDID 1.4 Established Timings III descriptor" is quite surprising. It looks like we've never got any of them right. I am not sure what the full implications of this are. That combined with lack of any details of real world bugs fixed made me decide against cc: stable. * tag 'topic/drm-fixes-2016-04-07' of git://anongit.freedesktop.org/drm-intel: drm/edid: Fix DMT 1024x768@43Hz (interlaced) timings drm/edid: Fix parsing of EDID 1.4 Established Timings III descriptor drm/edid: Fix EDID Established Timings I and II drm/qxl: fix cursor position with non-zero hotspot
2016-04-11m68k/gpio: remove arch specific sysfs bus deviceGreg Ungerer1-7/+1
The ColdFire architecture specific gpio support code registers a sysfs bus device named "gpio". This clashes with the new generic API device added in commit 3c702e99 ("gpio: add a userspace chardev ABI for GPIOs"). The old ColdFire sysfs gpio device was never used for anything specific, and no links or other nodes were created under it. The new API sysfs gpio device has all the same default sysfs links (device, drivers, etc) and they are properly populated. Remove the old ColdFire sysfs gpio registration. Signed-off-by: Greg Ungerer <[email protected]> Acked-by: Linus Walleij <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.