aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2015-03-22can: gs_usb: check for kzalloc allocation failureColin Ian King1-0/+2
smatch detected the following issue: drivers/net/can/usb/gs_usb.c:904 gs_usb_probe() error: potential null dereference 'dev'. (kzalloc returns null) Add a check for null return from kzalloc and return -ENOMEM Signed-off-by: Colin Ian King <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2015-03-22can: kvaser_usb: Fix sparse warning __le16 degrades to integerAhmed S. Darwish1-3/+4
USB endpoint's wMaxPacketSize field is an le16 entity. Use appropriate le16_to_cpu macros to maintain endian independence. Reported-by: Marc Kleine-Budde <[email protected]> Signed-off-by: Ahmed S. Darwish <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2015-03-22can: kvaser_usb: Comply with firmware max tx URBs valueAhmed S. Darwish1-24/+38
Current driver code arbitrarily assumes a max outstanding tx value of 16 parallel transmissions. Meanwhile, the device firmware provides its actual maximum inside its reply to the CMD_GET_SOFTWARE_INFO message. Under heavy tx traffic, if the interleaved transmissions count increases above the limit reported by firmware, the firmware breaks up badly, reports a massive list of internal errors, and the candump traces hardly matches the actual frames sent and received. On the other hand, in certain models, the firmware can support up to 48 tx URBs instead of just 16, increasing the driver throughput by two-fold and reducing the possibility of -ENOBUFs. Thus dynamically set the driver's max tx URBs value according to firmware replies. Signed-off-by: Ahmed S. Darwish <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2015-03-22rtlwifi: Fix IOMMU mapping leak in AP modeLarry Finger1-1/+11
Transmission of an AP beacon does not call the TX interrupt service routine, which usually does the cleanup. Instead, cleanup is handled in a tasklet completion routine. Unfortunately, this routine has a serious bug in that it does not release the DMA mapping before it frees the skb, thus one IOMMU mapping is leaked for each beacon. The test system failed with no free IOMMU mapping slots approximately one hour after hostapd was used to start an AP. This issue was reported and tested at https://github.com/lwfinger/rtlwifi_new/issues/30. Reported-and-tested-by: Kevin Mullican <[email protected]> Cc: Kevin Mullican <[email protected]> Signed-off-by: Shao Fu <[email protected]> Signed-off-by: Larry Finger <[email protected]> Cc: Stable <[email protected]> [3.18+] Signed-off-by: Kalle Valo <[email protected]>
2015-03-21cx82310_eth: wait for firmware to become readyOndrej Zary1-6/+24
When the device is powered up, some (older) firmware versions fail to work properly if we send commands before the boot is complete (everything is OK when the device is hot-plugged). The firmware indicates its ready status by putting the link up. Newer firmwares delay the first command so they don't suffer from this problem. They also report the link being always up. Wait for firmware to become ready (link up) before sending any commands and/or data. This also allows lowering CMD_TIMEOUT value to a reasonable time. Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions. Signed-off-by: Ondrej Zary <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-03-21Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds5-80/+137
Pull slave dmaengine fixes from Vinod Koul: "Four fixes for dw, pl08x, imx-sdma and at_hdmac driver. Nothing unusual here, simple fixes to these drivers" * 'fixes' of git://git.infradead.org/users/vkoul/slave-dma: dmaengine: pl08x: Define capabilities for generic capabilities reporting dmaengine: dw: append MODULE_ALIAS for platform driver dmaengine: imx-sdma: switch to dynamic context mode after script loaded dmaengine: at_hdmac: Fix calculation of the residual bytes
2015-03-21Merge tag 'pm+acpi-4.0-rc5' of ↵Linus Torvalds8-54/+78
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management and ACPI fixes from Rafael Wysocki: "These are fixes for recent regressions (PCI/ACPI resources and at91 RTC locking), a stable-candidate powercap RAPL driver fix and two ARM cpuidle fixes (one stable-candidate too). Specifics: - Revert a recent PCI commit related to IRQ resources management that introduced a regression for drivers attempting to bind to devices whose previous drivers did not balance pci_enable_device() and pci_disable_device() as expected (Rafael J Wysocki). - Fix a deadlock in at91_rtc_interrupt() introduced by a typo in a recent commit related to wakeup interrupt handling (Dan Carpenter). - Allow the power capping RAPL (Running-Average Power Limit) driver to use different energy units for domains within one CPU package which is necessary to handle Intel Haswell EP processors correctly (Jacob Pan). - Improve the cpuidle mvebu driver's handling of Armada XP SoCs by updating the target residency and exit latency numbers for those chips (Sebastien Rannou). - Prevent the cpuidle mvebu driver from calling cpu_pm_enter() twice in a row before cpu_pm_exit() is called on the same CPU which breaks the core's assumptions regarding the usage of those functions (Gregory Clement)" * tag 'pm+acpi-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: Revert "x86/PCI: Refine the way to release PCI IRQ resources" rtc: at91rm9200: double locking bug in at91_rtc_interrupt() powercap / RAPL: handle domains with different energy units cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs cpuidle: mvebu: Fix the CPU PM notifier usage
2015-03-21Merge git://people.freedesktop.org/~airlied/linuxLinus Torvalds18-372/+159
Pull drm updates from Dave Airlie: "A bunch of fixes across drivers: radeon: disable two ended allocation for now, it breaks some stuff amdkfd: misc fixes nouveau: fix irq loop problem, add basic support for GM206 (new hw) i915: fix some WARNs people were seeing exynos: fix some iommu interactions causing boot failures" * git://people.freedesktop.org/~airlied/linux: drm/radeon: drop ttm two ended allocation drm/exynos: fix the initialization order in FIMD drm/exynos: fix typo config name correctly. drm/exynos: Check for NULL dereference of crtc drm/exynos: IS_ERR() vs NULL bug drm/exynos: remove unused files drm/i915: Make sure the primary plane is enabled before reading out the fb state drm/nouveau/bios: fix i2c table parsing for dcb 4.1 drm/nouveau/device/gm100: Basic GM206 bring up (as copy of GM204) drm/nouveau/device: post write to NV_PMC_BOOT_1 when flipping endian switch drm/nouveau/gr/gf100: fix some accidental or'ing of buffer addresses drm/nouveau/fifo/nv04: remove the loop from the interrupt handler drm/radeon: Changing number of compute pipe lines drm/amdkfd: Fix SDMA queue init. in non-HWS mode drm/amdkfd: destroy mqd when destroying kernel queue drm/i915: Ensure plane->state->fb stays in sync with plane->fb
2015-03-21Merge tag 'devicetree-fixes-for-4.0-part2' of ↵Linus Torvalds3-12/+14
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux Pull more DeviceTree fixes vfom Rob Herring: - revert setting stdout-path as preferred console. This caused regressions in PowerMACs and other systems. - yet another fix for stdout-path option parsing. - fix error path handling in of_irq_parse_one * tag 'devicetree-fixes-for-4.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: Revert "of: Fix premature bootconsole disable with 'stdout-path'" of: handle both '/' and ':' in path strings of: unittest: Add option string test case with longer path of/irq: Fix of_irq_parse_one() returned error codes
2015-03-21Merge git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pendingLinus Torvalds14-47/+61
Pull SCSI target fixes from Nicholas Bellinger: "Here are current target-pending fixes for v4.0-rc5 code that have made their way into the queue over the last weeks. The fixes this round include: - Fix long-standing iser-target logout bug related to early conn_logout_comp completion, resulting in iscsi_conn use-after-tree OOpsen. (Sagi + nab) - Fix long-standing tcm_fc bug in ft_invl_hw_context() failure handing for DDP hw offload. (DanC) - Fix incorrect use of unprotected __transport_register_session() in tcm_qla2xxx + other single local se_node_acl fabrics. (Bart) - Fix reference leak in target_submit_cmd() -> target_get_sess_cmd() for ack_kref=1 failure path. (Bart) - Fix pSCSI backend ->get_device_type() statistics OOPs with un-configured device. (Olaf + nab) - Fix virtual LUN=0 target_configure_device failure OOPs at modprobe time. (Claudio + nab) - Fix FUA write false positive failure regression in v4.0-rc1 code. (Christophe Vu-Brugier + HCH)" * git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: target: do not reject FUA CDBs when write cache is enabled but emulate_write_cache is 0 target: Fix virtual LUN=0 target_configure_device failure OOPs target/pscsi: Fix NULL pointer dereference in get_device_type tcm_fc: missing curly braces in ft_invl_hw_context() target: Fix reference leak in target_get_sess_cmd() error path loop/usb/vhost-scsi/xen-scsiback: Fix use of __transport_register_session tcm_qla2xxx: Fix incorrect use of __transport_register_session iscsi-target: Avoid early conn_logout_comp for iser connections Revert "iscsi-target: Avoid IN_LOGOUT failure case for iser-target" target: Disallow changing of WRITE cache/FUA attrs after export
2015-03-21Merge tag 'dm-4.0-fixes' of ↵Linus Torvalds5-26/+142
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm Pull devicemapper fixes from Mike Snitzer: "A handful of stable fixes for DM: - fix thin target to always zero-fill reads to unprovisioned blocks - fix to interlock device destruction's suspend from internal suspends - fix 2 snapshot exception store handover bugs - fix dm-io to cope with DISCARD and WRITE_SAME capabilities changing" * tag 'dm-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: dm io: deal with wandering queue limits when handling REQ_DISCARD and REQ_WRITE_SAME dm snapshot: suspend merging snapshot when doing exception handover dm snapshot: suspend origin when doing exception handover dm: hold suspend_lock while suspending device during device deletion dm thin: fix to consistently zero-fill reads to unprovisioned blocks
2015-03-21Merge branch 'for-linus' of ↵Linus Torvalds8-46/+352
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs Pull btrfs fixes from Chris Mason: "Most of these are fixing extent reservation accounting, or corners with tree writeback during commit. Josef's set does add a test, which isn't strictly a fix, but it'll keep us from making this same mistake again" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: Btrfs: fix outstanding_extents accounting in DIO Btrfs: add sanity test for outstanding_extents accounting Btrfs: just free dummy extent buffers Btrfs: account merges/splits properly Btrfs: prepare block group cache before writing Btrfs: fix ASSERT(list_empty(&cur_trans->dirty_bgs_list) Btrfs: account for the correct number of extents for delalloc reservations Btrfs: fix merge delalloc logic Btrfs: fix comp_oper to get right order Btrfs: catch transaction abortion after waiting for it btrfs: fix sizeof format specifier in btrfs_check_super_valid()
2015-03-21Merge branch 'for-4.0' of git://linux-nfs.org/~bfields/linuxLinus Torvalds1-2/+0
Pull nfsd bufix from Bruce Fields: "This is a fix for a crash easily triggered by 4.1 activity to a server built with CONFIG_NFSD_PNFS. There are some more bugfixes queued up that I intend to pass along next week, but this is the most critical" * 'for-4.0' of git://linux-nfs.org/~bfields/linux: Subject: nfsd: don't recursively call nfsd4_cb_layout_fail
2015-03-21Merge tag 'upstream-4.0-rc5' of git://git.infradead.org/linux-ubifsLinus Torvalds1-1/+2
Pull UBI fix from Artem Bityutskiy: "This fixes a bug introduced during the v4.0 merge window where we forgot to put braces where they should be" * tag 'upstream-4.0-rc5' of git://git.infradead.org/linux-ubifs: UBI: fix missing brace control flow
2015-03-21Merge tag 'arm64-fixes' of ↵Linus Torvalds3-5/+19
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fixes from Catalin Marinas: - mm switching fix where the kernel pgd ends up in the user TTBR0 after returning from an EFI run-time services call - fix __GFP_ZERO handling for atomic pool and CMA DMA allocations (the generic code does get the gfp flags, so it's left with the arch code to memzero accordingly) * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: Honor __GFP_ZERO in dma allocations arm64: efi: don't restore TTBR0 if active_mm points at init_mm
2015-03-21Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds5-23/+23
Pull ARM fixes from Russell King: "Another few ARM fixes. Fabrice fixed the L2 cache DT parsing to allow prefetch configuration to be specified even when the cache size parsing fails. Laura noticed that the setting of page attributes wasn't working for modules due to is_module_addr() always returning false. Marc Gonzalez (aka Mason) noticed a potential latent bug with the way we read one of the CPUID registers (where we could attempt to read a non-present CPUID register which may fault.) I've fixed an issue where 32-bit DMA masks were failing with memory which extended to the top of physical address space, and I've also added debugging output of the page tables when we hit a data access exception which we don't specifically handle - prompted by the lack of information in a bug report" * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: 8313/1: Use read_cpuid_ext() macro instead of inline asm ARM: 8311/1: Don't use is_module_addr in setting page attributes ARM: 8310/1: l2c: Fix prefetch settings dt parsing ARM: dump pgd, pmd and pte states on unhandled data abort faults ARM: dma-api: fix off-by-one error in __dma_supported()
2015-03-21cifs: potential memory leaks when parsing mnt optsTaesoo Kim1-0/+4
For example, when mount opt is redundently specified (e.g., "user=A,user=B,user=C"), kernel kept allocating new key/val with kstrdup() and overwrite previous ptr (to be freed). Althouhg mount.cifs in userspace performs a bit of sanitization (e.g., forcing one user option), current implementation is not robust. Other options such as iocharset and domainanme are similarly vulnerable. Signed-off-by: Taesoo Kim <[email protected]> Signed-off-by: Steve French <[email protected]>
2015-03-21cifs: fix use-after-free bug in find_writable_fileDavid Disseldorp1-0/+1
Under intermittent network outages, find_writable_file() is susceptible to the following race condition, which results in a user-after-free in the cifs_writepages code-path: Thread 1 Thread 2 ======== ======== inv_file = NULL refind = 0 spin_lock(&cifs_file_list_lock) // invalidHandle found on openFileList inv_file = open_file // inv_file->count currently 1 cifsFileInfo_get(inv_file) // inv_file->count = 2 spin_unlock(&cifs_file_list_lock); cifs_reopen_file() cifs_close() // fails (rc != 0) ->cifsFileInfo_put() spin_lock(&cifs_file_list_lock) // inv_file->count = 1 spin_unlock(&cifs_file_list_lock) spin_lock(&cifs_file_list_lock); list_move_tail(&inv_file->flist, &cifs_inode->openFileList); spin_unlock(&cifs_file_list_lock); cifsFileInfo_put(inv_file); ->spin_lock(&cifs_file_list_lock) // inv_file->count = 0 list_del(&cifs_file->flist); // cleanup!! kfree(cifs_file); spin_unlock(&cifs_file_list_lock); spin_lock(&cifs_file_list_lock); ++refind; // refind = 1 goto refind_writable; At this point we loop back through with an invalid inv_file pointer and a refind value of 1. On second pass, inv_file is not overwritten on openFileList traversal, and is subsequently dereferenced. Signed-off-by: David Disseldorp <[email protected]> Reviewed-by: Jeff Layton <[email protected]> CC: <[email protected]> Signed-off-by: Steve French <[email protected]>
2015-03-21cifs: smb2_clone_range() - exit on unhandled errorSachin Prabhu1-1/+2
While attempting to clone a file on a samba server, we receive a STATUS_INVALID_DEVICE_REQUEST. This is mapped to -EOPNOTSUPP which isn't handled in smb2_clone_range(). We end up looping in the while loop making same call to the samba server over and over again. The proposed fix is to exit and return the error value when encountered with an unhandled error. Cc: <[email protected]> Signed-off-by: Sachin Prabhu <[email protected]> Signed-off-by: Steve French <[email protected]> Signed-off-by: Steve French <[email protected]>
2015-03-21brcmfmac: disable MBSS feature for BCM43362Arend van Spriel1-1/+2
The BCM43362 firmware falsely reports it is capable of providing MBSS. As a result AP mode no longer works for this device. Therefor disable MBSS in the driver for this chipset. Cc: [email protected] # 3.19.y Reported-by: Jorg Krause <[email protected]> Reviewed-by: Hante Meuleman <[email protected]> Reviewed-by: Pieter-Paul Giesberts <[email protected]> Signed-off-by: Arend van Spriel <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2015-03-21Merge branches 'pm-cpuidle', 'powercap', 'irq-pm' and 'acpi-resources'Rafael J. Wysocki266-1509/+2867
* pm-cpuidle: cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs cpuidle: mvebu: Fix the CPU PM notifier usage * powercap: powercap / RAPL: handle domains with different energy units * irq-pm: rtc: at91rm9200: double locking bug in at91_rtc_interrupt() * acpi-resources: Revert "x86/PCI: Refine the way to release PCI IRQ resources"
2015-03-21md: fix problems with freeing private data after ->run failure.NeilBrown2-3/+2
If ->run() fails, it can either free the data structures it allocated, or leave that task to ->free() which will be called on failures. However: md.c calls ->free() even if ->private_data is NULL, which causes problems in some personalities. raid0.c frees the data, but doesn't clear ->private_data, which will become a problem when we fix md.c So better fix both these issues at once. Reported-by: Richard W.M. Jones <[email protected]> Fixes: 5aa61f427e4979be733e4847b9199ff9cc48a47e URL: https://bugzilla.kernel.org/show_bug.cgi?id=94381 Signed-off-by: NeilBrown <[email protected]>
2015-03-20net: validate the range we feed to iov_iter_init() in sys_sendto/sys_recvfromAl Viro1-0/+4
Cc: [email protected] # v3.19 Signed-off-by: Al Viro <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-03-20net: compat: Update get_compat_msghdr() to match copy_msghdr_from_user() ↵Catalin Marinas1-0/+7
behaviour Commit db31c55a6fb2 (net: clamp ->msg_namelen instead of returning an error) introduced the clamping of msg_namelen when the unsigned value was larger than sizeof(struct sockaddr_storage). This caused a msg_namelen of -1 to be valid. The native code was subsequently fixed by commit dbb490b96584 (net: socket: error on a negative msg_namelen). In addition, the native code sets msg_namelen to 0 when msg_name is NULL. This was done in commit (6a2a2b3ae075 net:socket: set msg_namelen to 0 if msg_name is passed as NULL in msghdr struct from userland) and subsequently updated by 08adb7dabd48 (fold verify_iovec() into copy_msghdr_from_user()). This patch brings the get_compat_msghdr() in line with copy_msghdr_from_user(). Fixes: db31c55a6fb2 (net: clamp ->msg_namelen instead of returning an error) Cc: David S. Miller <[email protected]> Cc: Dan Carpenter <[email protected]> Signed-off-by: Catalin Marinas <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-03-20NFSD: Put exports after nfsd4_layout_verify failKinglong Mee1-1/+1
Fix commit 9cf514ccfa (nfsd: implement pNFS operations). Signed-off-by: Kinglong Mee <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Signed-off-by: J. Bruce Fields <[email protected]>
2015-03-20arm64: Honor __GFP_ZERO in dma allocationsSuzuki K. Poulose1-3/+9
Current implementation doesn't zero out the pages allocated. Honor the __GFP_ZERO flag and zero out if set. Cc: <[email protected]> # v3.14+ Acked-by: Will Deacon <[email protected]> Signed-off-by: Suzuki K. Poulose <[email protected]> Signed-off-by: Catalin Marinas <[email protected]>
2015-03-20Merge branch 'be2net'David S. Miller4-44/+108
Sathya Perla says: ==================== be2net: patch set Hi David, this patch set includes 3 bug fixes to the be2net driver. Patch 1 fixes a vlan isolation issue with VFs. When a VF is placed in promiscous mode, it could receive packets belonging to any vlan, as the PF driver grants vlan promisc capability to VFs. The PF driver now disables the vlan promisc capability for VFs to fix this problem. Patch 2 fixes the call to MODIFY_EQ_DELAY FW cmd to not include more than 8 EQs per cmd. The FW is not capable of handling more than 8 EQs per cmd. Patch 3 fixes an EEH error detection issue. On Power platforms, when an EEH error occurs, the slot disconnect state is more reliably detected via an MMIO read compared to a config read. So, the error register reads that occur every second are now done via MMIO. Pls apply this patch set to the "net" tree. Thanks! ==================== Signed-off-by: David S. Miller <[email protected]>
2015-03-20be2net: use PCI MMIO read instead of config read for errorsSuresh Reddy2-11/+23
When an EEH error occurs, the device/slot is disconnected. This condition is more reliably detected (i.e., returns all ones) with an MMIO read rather than a config read -- especially on power platforms. Hence, this patch fixes EEH error detection by replacing config reads with MMIO reads for reading the error registers. The error registers in Skyhawk-R/BE2/BE3 are accessible both via the config space and the PCICFG (BAR0) memory space. Reported-by: Gavin Shan <[email protected]> Signed-off-by: Suresh Reddy <[email protected]> Signed-off-by: Sathya Perla <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-03-20be2net: restrict MODIFY_EQ_DELAY cmd to a max of 8 EQsSuresh Reddy1-9/+5
Issuing this cmd for more than 8 EQs does not have the intended effect even on BEx and Skyhawk-R. This patch fixes this by issuing this cmd for upto 8 EQs at a time. Signed-off-by: Suresh Reddy <[email protected]> Signed-off-by: Sathya Perla <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-03-20be2net: Prevent VFs from enabling VLAN promiscuous modeVasundhara Volam4-24/+80
Currently, a PF does not restrict its VF interface from enabling vlan promiscuous mode. This breaks vlan isolation when a vlan (transparent tagging) is configured on a VF. This patch fixes this problem by disabling the vlan promisc capability for VFs. Reported-by: Yoann Juet <[email protected]> Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Sathya Perla <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-03-20tcp: fix tcp fin memory accountingJosh Hunt1-5/+1
tcp_send_fin() does not account for the memory it allocates properly, so sk_forward_alloc can be negative in cases where we've sent a FIN: ss example output (ss -amn | grep -B1 f4294): tcp FIN-WAIT-1 0 1 192.168.0.1:45520 192.0.2.1:8080 skmem:(r0,rb87380,t0,tb87380,f4294966016,w1280,o0,bl0) Acked-by: Eric Dumazet <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-03-20arm64: efi: don't restore TTBR0 if active_mm points at init_mmWill Deacon2-2/+10
init_mm isn't a normal mm: it has swapper_pg_dir as its pgd (which contains kernel mappings) and is used as the active_mm for the idle thread. When restoring the pgd after an EFI call, we write current->active_mm into TTBR0. If the current task is actually the idle thread (e.g. when initialising the EFI RTC before entering userspace), then the TLB can erroneously populate itself with junk global entries as a result of speculative table walks. When we do eventually return to userspace, the task can end up hitting these junk mappings leading to lockups, corruption or crashes. This patch fixes the problem in the same way as the CPU suspend code by ensuring that we never switch to the init_mm in efi_set_pgd and instead point TTBR0 at the zero page. A check is also added to cpu_switch_mm to BUG if we get passed swapper_pg_dir. Reviewed-by: Ard Biesheuvel <[email protected]> Fixes: f3cdfd239da5 ("arm64/efi: move SetVirtualAddressMap() to UEFI stub") Signed-off-by: Will Deacon <[email protected]> Signed-off-by: Catalin Marinas <[email protected]>
2015-03-20ipv6: fix backtracking for throw routesSteven Barth1-0/+1
for throw routes to trigger evaluation of other policy rules EAGAIN needs to be propagated up to fib_rules_lookup similar to how its done for IPv4 A simple testcase for verification is: ip -6 rule add lookup 33333 priority 33333 ip -6 route add throw 2001:db8::1 ip -6 route add 2001:db8::1 via fe80::1 dev wlan0 table 33333 ip route get 2001:db8::1 Signed-off-by: Steven Barth <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-03-20net: ethernet: pcnet32: Setup the SRAM and NOUFLO on Am79C97{3, 5}Markos Chandras1-2/+29
On a MIPS Malta board, tons of fifo underflow errors have been observed when using u-boot as bootloader instead of YAMON. The reason for that is that YAMON used to set the pcnet device to SRAM mode but u-boot does not. As a result, the default Tx threshold (64 bytes) is now too small to keep the fifo relatively used and it can result to Tx fifo underflow errors. As a result of which, it's best to setup the SRAM on supported controllers so we can always use the NOUFLO bit. Cc: <[email protected]> Cc: <[email protected]> Cc: <[email protected]> Cc: Don Fry <[email protected]> Signed-off-by: Markos Chandras <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-03-20ipv6: call ipv6_proxy_select_ident instead of ipv6_select_ident in ↵Sabrina Dubroca1-5/+3
udp6_ufo_fragment Matt Grant reported frequent crashes in ipv6_select_ident when udp6_ufo_fragment is called from openvswitch on a skb that doesn't have a dst_entry set. ipv6_proxy_select_ident generates the frag_id without using the dst associated with the skb. This approach was suggested by Vladislav Yasevich. Fixes: 0508c07f5e0c ("ipv6: Select fragment id during UFO segmentation if not set.") Cc: Vladislav Yasevich <[email protected]> Reported-by: Matt Grant <[email protected]> Tested-by: Matt Grant <[email protected]> Signed-off-by: Sabrina Dubroca <[email protected]> Acked-by: Vladislav Yasevich <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-03-20Input: add MT_TOOL_PALMCharlie Mooney2-4/+8
Currently there are only two "tools" that can be specified by a multi-touch driver: MT_TOOL_FINGER and MT_TOOL_PEN. In working with Elan (The touch vendor) and discussing their next-gen devices it seems that it will be useful to have more tools so that their devices can give the upper layers of the stack hints as to what is touching the sensor. In particular they have new experimental firmware that can better differentiate between palms vs fingertips and would like to plumb a patch so that we can use their hints in higher-level gesture soft- ware. The firmware on the device can reasonably do a better job of palm detection because it has access to all of the raw sensor readings as opposed to just the width/pressure/etc that are exposed by the driver. As such, the firmware can characterize what a palm looks like in much finer-grained detail and this change would allow such a device to share its findings with the kernel. Signed-off-by: Charlie Mooney <[email protected]> Acked-by: Peter Hutterer <[email protected]> Signed-off-by: Dmitry Torokhov <[email protected]>
2015-03-20NFSD: Error out when register_shrinker() failKinglong Mee1-1/+5
If register_shrinker() failed, nfsd will cause a NULL pointer access as, [ 9250.875465] nfsd: last server has exited, flushing export cache [ 9251.427270] BUG: unable to handle kernel NULL pointer dereference at (null) [ 9251.427393] IP: [<ffffffff8136fc29>] __list_del_entry+0x29/0xd0 [ 9251.427579] PGD 13e4d067 PUD 13e4c067 PMD 0 [ 9251.427633] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC [ 9251.427706] Modules linked in: ip6t_rpfilter ip6t_REJECT bnep bluetooth xt_conntrack cfg80211 rfkill ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw btrfs xfs microcode ppdev serio_raw pcspkr xor libcrc32c raid6_pq e1000 parport_pc parport i2c_piix4 i2c_core nfsd(OE-) auth_rpcgss nfs_acl lockd sunrpc(E) ata_generic pata_acpi [ 9251.428240] CPU: 0 PID: 1557 Comm: rmmod Tainted: G OE 3.16.0-rc2+ #22 [ 9251.428366] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/31/2013 [ 9251.428496] task: ffff880000849540 ti: ffff8800136f4000 task.ti: ffff8800136f4000 [ 9251.428593] RIP: 0010:[<ffffffff8136fc29>] [<ffffffff8136fc29>] __list_del_entry+0x29/0xd0 [ 9251.428696] RSP: 0018:ffff8800136f7ea0 EFLAGS: 00010207 [ 9251.428751] RAX: 0000000000000000 RBX: ffffffffa0116d48 RCX: dead000000200200 [ 9251.428814] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffa0116d48 [ 9251.428876] RBP: ffff8800136f7ea0 R08: ffff8800136f4000 R09: 0000000000000001 [ 9251.428939] R10: 8080808080808080 R11: 0000000000000000 R12: ffffffffa011a5a0 [ 9251.429002] R13: 0000000000000800 R14: 0000000000000000 R15: 00000000018ac090 [ 9251.429064] FS: 00007fb9acef0740(0000) GS:ffff88003fa00000(0000) knlGS:0000000000000000 [ 9251.429164] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 9251.429221] CR2: 0000000000000000 CR3: 0000000031a17000 CR4: 00000000001407f0 [ 9251.429306] Stack: [ 9251.429410] ffff8800136f7eb8 ffffffff8136fcdd ffffffffa0116d20 ffff8800136f7ed0 [ 9251.429511] ffffffff8118a0f2 0000000000000000 ffff8800136f7ee0 ffffffffa00eb765 [ 9251.429610] ffff8800136f7ef0 ffffffffa010e93c ffff8800136f7f78 ffffffff81104ac2 [ 9251.429709] Call Trace: [ 9251.429755] [<ffffffff8136fcdd>] list_del+0xd/0x30 [ 9251.429896] [<ffffffff8118a0f2>] unregister_shrinker+0x22/0x40 [ 9251.430037] [<ffffffffa00eb765>] nfsd_reply_cache_shutdown+0x15/0x90 [nfsd] [ 9251.430106] [<ffffffffa010e93c>] exit_nfsd+0x9/0x6cd [nfsd] [ 9251.430192] [<ffffffff81104ac2>] SyS_delete_module+0x162/0x200 [ 9251.430280] [<ffffffff81013b69>] ? do_notify_resume+0x59/0x90 [ 9251.430395] [<ffffffff816f2369>] system_call_fastpath+0x16/0x1b [ 9251.430457] Code: 00 00 55 48 8b 17 48 b9 00 01 10 00 00 00 ad de 48 8b 47 08 48 89 e5 48 39 ca 74 29 48 b9 00 02 20 00 00 00 ad de 48 39 c8 74 7a <4c> 8b 00 4c 39 c7 75 53 4c 8b 42 08 4c 39 c7 75 2b 48 89 42 08 [ 9251.430691] RIP [<ffffffff8136fc29>] __list_del_entry+0x29/0xd0 [ 9251.430755] RSP <ffff8800136f7ea0> [ 9251.430805] CR2: 0000000000000000 [ 9251.431033] ---[ end trace 080f3050d082b4ea ]--- Signed-off-by: Kinglong Mee <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Signed-off-by: J. Bruce Fields <[email protected]>
2015-03-20NFSD: Take care the return value from nfsd4_decode_stateidKinglong Mee1-3/+15
Return status after nfsd4_decode_stateid failed. Signed-off-by: Kinglong Mee <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Signed-off-by: J. Bruce Fields <[email protected]>
2015-03-20NFSD: Check layout type when returning client layoutsKinglong Mee1-0/+3
According to RFC5661: " When lr_returntype is LAYOUTRETURN4_FSID, the current filehandle is used to identify the file system and all layouts matching the client ID, the fsid of the file system, lora_layout_type, and lora_iomode are returned. When lr_returntype is LAYOUTRETURN4_ALL, all layouts matching the client ID, lora_layout_type, and lora_iomode are returned and the current filehandle is not used. " When returning client layouts, always check layout type. Signed-off-by: Kinglong Mee <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Signed-off-by: J. Bruce Fields <[email protected]>
2015-03-20NFSD: restore trace event lost in mismergeKinglong Mee1-0/+2
31ef83dc05 "nfsd: add trace events" had a typo that dropped a trace event and replaced it by an incorrect recursive call to nfsd4_cb_layout_fail. 133d558216d9 "Subject: nfsd: don't recursively call nfsd4_cb_layout_fail" fixed the crash, this restores the tracepoint. Reviewed-by: Christoph Hellwig <[email protected]> Signed-off-by: Kinglong Mee <[email protected]> Signed-off-by: J. Bruce Fields <[email protected]>
2015-03-20Fix bug in blk_rq_merge_okWenbo Wang1-1/+1
Use the right array index to reference the last element of rq->biotail->bi_io_vec[] Signed-off-by: Wenbo Wang <[email protected]> Reviewed-by: Chong Yuan <[email protected]> Fixes: 66cb45aa41315 ("block: add support for limiting gaps in SG lists") Cc: [email protected] Signed-off-by: Jens Axboe <[email protected]>
2015-03-20Revert "x86/PCI: Refine the way to release PCI IRQ resources"Rafael J. Wysocki5-32/+32
Commit b4b55cda5874 (Refine the way to release PCI IRQ resources) introduced a regression in the PCI IRQ resource management by causing the IRQ resource of a device, established when pci_enabled_device() is called on a fully disabled device, to be released when the driver is unbound from the device, regardless of the enable_cnt. This leads to the situation that an ill-behaved driver can now make a device unusable to subsequent drivers by an imbalance in their use of pci_enable/disable_device(). That is a serious problem for secondary drivers like vfio-pci, which are innocent of the transgressions of the previous driver. Since the solution of this problem is not immediate and requires further discussion, revert commit b4b55cda5874 and the issue it was supposed to address (a bug related to xen-pciback) will be taken care of in a different way going forward. Reported-by: Alex Williamson <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2015-03-20netfilter: xt_TPROXY: fix invflags check in tproxy_tg6_check()Pablo Neira Ayuso1-2/+2
We have to check for IP6T_INV_PROTO in invflags, instead of flags. Signed-off-by: Pablo Neira Ayuso <[email protected]> Acked-by: Balazs Scheidler <[email protected]>
2015-03-20KVM: PPC: Book3S HV: Fix instruction emulationPaul Mackerras1-0/+1
Commit 4a157d61b48c ("KVM: PPC: Book3S HV: Fix endianness of instruction obtained from HEIR register") had the side effect that we no longer reset vcpu->arch.last_inst to -1 on guest exit in the cases where the instruction is not fetched from the guest. This means that if instruction emulation turns out to be required in those cases, the host will emulate the wrong instruction, since vcpu->arch.last_inst will contain the last instruction that was emulated. This fixes it by making sure that vcpu->arch.last_inst is reset to -1 in those cases. Signed-off-by: Paul Mackerras <[email protected]> Signed-off-by: Alexander Graf <[email protected]>
2015-03-20KVM: PPC: Book3S HV: Endian fix for accessing VPA yield countPaul Mackerras1-1/+1
The VPA (virtual processor area) is defined by PAPR and is therefore big-endian, so we need a be32_to_cpu when reading it in kvmppc_get_yield_count(). Without this, H_CONFER always fails on a little-endian host, causing SMP guests to waste time spinning on spinlocks. Signed-off-by: Paul Mackerras <[email protected]> Signed-off-by: Alexander Graf <[email protected]>
2015-03-20KVM: PPC: Book3S HV: Fix spinlock/mutex ordering issue in kvmppc_set_lpcr()Paul Mackerras1-3/+3
Currently, kvmppc_set_lpcr() has a spinlock around the whole function, and inside that does mutex_lock(&kvm->lock). It is not permitted to take a mutex while holding a spinlock, because the mutex_lock might call schedule(). In addition, this causes lockdep to warn about a lock ordering issue: ====================================================== [ INFO: possible circular locking dependency detected ] 3.18.0-kvm-04645-gdfea862-dirty #131 Not tainted ------------------------------------------------------- qemu-system-ppc/8179 is trying to acquire lock: (&kvm->lock){+.+.+.}, at: [<d00000000ecc1f54>] .kvmppc_set_lpcr+0xf4/0x1c0 [kvm_hv] but task is already holding lock: (&(&vcore->lock)->rlock){+.+...}, at: [<d00000000ecc1ea0>] .kvmppc_set_lpcr+0x40/0x1c0 [kvm_hv] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&(&vcore->lock)->rlock){+.+...}: [<c000000000b3c120>] .mutex_lock_nested+0x80/0x570 [<d00000000ecc7a14>] .kvmppc_vcpu_run_hv+0xc4/0xe40 [kvm_hv] [<d00000000eb9f5cc>] .kvmppc_vcpu_run+0x2c/0x40 [kvm] [<d00000000eb9cb24>] .kvm_arch_vcpu_ioctl_run+0x54/0x160 [kvm] [<d00000000eb94478>] .kvm_vcpu_ioctl+0x4a8/0x7b0 [kvm] [<c00000000026cbb4>] .do_vfs_ioctl+0x444/0x770 [<c00000000026cfa4>] .SyS_ioctl+0xc4/0xe0 [<c000000000009264>] syscall_exit+0x0/0x98 -> #0 (&kvm->lock){+.+.+.}: [<c0000000000ff28c>] .lock_acquire+0xcc/0x1a0 [<c000000000b3c120>] .mutex_lock_nested+0x80/0x570 [<d00000000ecc1f54>] .kvmppc_set_lpcr+0xf4/0x1c0 [kvm_hv] [<d00000000ecc510c>] .kvmppc_set_one_reg_hv+0x4dc/0x990 [kvm_hv] [<d00000000eb9f234>] .kvmppc_set_one_reg+0x44/0x330 [kvm] [<d00000000eb9c9dc>] .kvm_vcpu_ioctl_set_one_reg+0x5c/0x150 [kvm] [<d00000000eb9ced4>] .kvm_arch_vcpu_ioctl+0x214/0x2c0 [kvm] [<d00000000eb940b0>] .kvm_vcpu_ioctl+0xe0/0x7b0 [kvm] [<c00000000026cbb4>] .do_vfs_ioctl+0x444/0x770 [<c00000000026cfa4>] .SyS_ioctl+0xc4/0xe0 [<c000000000009264>] syscall_exit+0x0/0x98 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&(&vcore->lock)->rlock); lock(&kvm->lock); lock(&(&vcore->lock)->rlock); lock(&kvm->lock); *** DEADLOCK *** 2 locks held by qemu-system-ppc/8179: #0: (&vcpu->mutex){+.+.+.}, at: [<d00000000eb93f18>] .vcpu_load+0x28/0x90 [kvm] #1: (&(&vcore->lock)->rlock){+.+...}, at: [<d00000000ecc1ea0>] .kvmppc_set_lpcr+0x40/0x1c0 [kvm_hv] stack backtrace: CPU: 4 PID: 8179 Comm: qemu-system-ppc Not tainted 3.18.0-kvm-04645-gdfea862-dirty #131 Call Trace: [c000001a66c0f310] [c000000000b486ac] .dump_stack+0x88/0xb4 (unreliable) [c000001a66c0f390] [c0000000000f8bec] .print_circular_bug+0x27c/0x3d0 [c000001a66c0f440] [c0000000000fe9e8] .__lock_acquire+0x2028/0x2190 [c000001a66c0f5d0] [c0000000000ff28c] .lock_acquire+0xcc/0x1a0 [c000001a66c0f6a0] [c000000000b3c120] .mutex_lock_nested+0x80/0x570 [c000001a66c0f7c0] [d00000000ecc1f54] .kvmppc_set_lpcr+0xf4/0x1c0 [kvm_hv] [c000001a66c0f860] [d00000000ecc510c] .kvmppc_set_one_reg_hv+0x4dc/0x990 [kvm_hv] [c000001a66c0f8d0] [d00000000eb9f234] .kvmppc_set_one_reg+0x44/0x330 [kvm] [c000001a66c0f960] [d00000000eb9c9dc] .kvm_vcpu_ioctl_set_one_reg+0x5c/0x150 [kvm] [c000001a66c0f9f0] [d00000000eb9ced4] .kvm_arch_vcpu_ioctl+0x214/0x2c0 [kvm] [c000001a66c0faf0] [d00000000eb940b0] .kvm_vcpu_ioctl+0xe0/0x7b0 [kvm] [c000001a66c0fcb0] [c00000000026cbb4] .do_vfs_ioctl+0x444/0x770 [c000001a66c0fd90] [c00000000026cfa4] .SyS_ioctl+0xc4/0xe0 [c000001a66c0fe30] [c000000000009264] syscall_exit+0x0/0x98 This fixes it by moving the mutex_lock()/mutex_unlock() pair outside the spin-locked region. Signed-off-by: Paul Mackerras <[email protected]> Signed-off-by: Alexander Graf <[email protected]>
2015-03-20Merge tag 'drm-intel-fixes-2015-03-19' of ↵Dave Airlie1-4/+28
git://anongit.freedesktop.org/drm-intel into drm-fixes Backporting a couple of plane related fixes from drm-next to v4.0. * tag 'drm-intel-fixes-2015-03-19' of git://anongit.freedesktop.org/drm-intel: drm/i915: Make sure the primary plane is enabled before reading out the fb state drm/i915: Ensure plane->state->fb stays in sync with plane->fb
2015-03-20Merge tag 'drm-amdkfd-fixes-2015-03-19' of ↵Dave Airlie3-11/+23
git://people.freedesktop.org/~gabbayo/linux into drm-fixes - Fixing SDMA initialization when in non-HWS mode (debug mode) - Memory leak fix when destroying kernel queue - Fix number of available compute pipelines according to new firmware * tag 'drm-amdkfd-fixes-2015-03-19' of git://people.freedesktop.org/~gabbayo/linux: drm/radeon: Changing number of compute pipe lines drm/amdkfd: Fix SDMA queue init. in non-HWS mode drm/amdkfd: destroy mqd when destroying kernel queue
2015-03-19target: do not reject FUA CDBs when write cache is enabled but ↵Christophe Vu-Brugier4-18/+17
emulate_write_cache is 0 A check that rejects a CDB with FUA bit set if no write cache is emulated was added by the following commit: fde9f50 target: Add sanity checks for DPO/FUA bit usage The condition is as follows: if (!dev->dev_attrib.emulate_fua_write || !dev->dev_attrib.emulate_write_cache) However, this check is wrong if the backend device supports WCE but "emulate_write_cache" is disabled. This patch uses se_dev_check_wce() (previously named spc_check_dev_wce) to invoke transport->get_write_cache() if the device has a write cache or check the "emulate_write_cache" attribute otherwise. Reported-by: Christoph Hellwig <[email protected]> Signed-off-by: Christophe Vu-Brugier <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]>
2015-03-19target: Fix virtual LUN=0 target_configure_device failure OOPsNicholas Bellinger1-2/+2
This patch fixes a NULL pointer dereference triggered by a late target_configure_device() -> alloc_workqueue() failure that results in target_free_device() being called with DF_CONFIGURED already set, which subsequently OOPses in destroy_workqueue() code. Currently this only happens at modprobe target_core_mod time when core_dev_setup_virtual_lun0() -> target_configure_device() fails, and the explicit target_free_device() gets called. To address this bug originally introduced by commit 0fd97ccf45, go ahead and move DF_CONFIGURED to end of target_configure_device() code to handle this special failure case. Reported-by: Claudio Fleiner <[email protected]> Cc: Claudio Fleiner <[email protected]> Cc: Christoph Hellwig <[email protected]> Cc: <[email protected]> # v3.7+ Signed-off-by: Nicholas Bellinger <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.