| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch removes the chip select function. Chip select should instead be
supported using GPIOs, defining the DT entry "cs-gpios", and letting the SPI
core assert/deassert the chip select as it sees fit.
The chip select control inside the controller is buggy. It is supposed to
automatically assert the chip select based on the activity in the controller,
but it is buggy and doesn't work at all. So instead we elect to use GPIOs.
Signed-off-by: Andy Gross <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c new drivers from Wolfram Sang:
"Here is a pull request from i2c hoping for the "new driver" rule.
Originally, I wanted to send this request during the merge window, but
code checkers with very recent additions complained, so a few fixups
were needed. So, some more time went by and I merged rc1 to get a
stable base"
So the "new driver" rule is really about drivers that people absolutely
need for the kernel to work on new hardware, which is not so much the
case for i2c. So I considered not pulling this, but eventually
relented.
Just for FYI: the whole (and only) point of "new drivers" is not that
new drivers cannot regress things (they can, and they have - by
triggering badly tested code on machines that never triggered that code
before), but because they can bring to life machines that otherwise
wouldn't be useful at all without the drivers.
So the new driver rule is for essential things that actual consumers
would care about, ie devices like networking or disk drivers that matter
to normal people (not server people - they run old kernels anyway, so
mainlining new drivers is irrelevant for them).
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sun6-p2wi: fix call to snprintf
i2c: rk3x: add NULL entry to the end of_device_id array
i2c: sun6i-p2wi: use proper return value in probe
i2c: sunxi: add P2WI (Push/Pull 2 Wire Interface) controller support
i2c: sunxi: add P2WI DT bindings documentation
i2c: rk3x: add driver for Rockchip RK3xxx SoC I2C adapter
|
|
Pull file locking fixes from Jeff Layton:
"File locking related bugfixes
Nothing too earth-shattering here. A fix for a potential regression
due to a patch in pile #1, and the addition of a memory barrier to
prevent a race condition between break_deleg and generic_add_lease"
* tag 'locks-v3.16-2' of git://git.samba.org/jlayton/linux:
locks: set fl_owner for leases back to current->files
locks: add missing memory barrier in break_deleg
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fixes from Michal Marek:
"There are three fixes for regressions caused by the relative paths
series: deb-pkg, tar-pkg and *docs did not work with O=.
Plus, there is a fix for the linux-headers deb package and a fixed
typo. These are not regression fixes but are safe enough"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: fix a typo in a kbuild document
builddeb: fix missing headers in linux-headers package
Documentation: Fix DocBook build with relative $(srctree)
kbuild: Fix tar-pkg with relative $(objtree)
deb-pkg: Fix for relative paths
|
|
Messages from the modem exceeding 256 bytes cause communication
failure.
The WDM protocol is strictly "read on demand", meaning that we only
poll for unread data after receiving a notification from the modem.
Since we have no way to know how much data the modem has to send,
we must make sure that the buffer we provide is "big enough".
Message truncation does not work. Truncated messages are left unread
until the modem has another message to send. Which often won't
happen until the userspace application has given up waiting for the
final part of the last message, and therefore sends another command.
With a proper CDC WDM function there is a descriptor telling us
which buffer size the modem uses. But with this vendor specific
implementation there is no known way to calculate the exact "big
enough" number. It is an unknown property of the modem firmware.
Experience has shown that 256 is too small. The discussion of
this failure ended up concluding that 512 might be too small as
well. So 1024 seems like a reasonable value for now.
Fixes: 41c47d8cfd68 ("net: huawei_cdc_ncm: Introduce the huawei_cdc_ncm driver")
Cc: Enrico Mioso <[email protected]>
Reported-by: Dan Williams <[email protected]>
Signed-off-by: Bjørn Mork <[email protected]>
Acked-By: Enrico Mioso <[email protected]>
Tested-by: Dan Williams <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This fixes some lockups in btrfs reported with rc1. It probably has
some performance impact because it is backing off our spinning locks
more often and switching to a blocking lock. I'll be able to nail
that down next week, but for now I want to get the lockups taken care
of.
Otherwise some more stack reduction and assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix wrong error handle when the device is missing or is not writeable
Btrfs: fix deadlock when mounting a degraded fs
Btrfs: use bio_endio_nodec instead of open code
Btrfs: fix NULL pointer crash when running balance and scrub concurrently
btrfs: Skip scrubbing removed chunks to avoid -ENOENT.
Btrfs: fix broken free space cache after the system crashed
Btrfs: make free space cache write out functions more readable
Btrfs: remove unused wait queue in struct extent_buffer
Btrfs: fix deadlocks with trylock on tree nodes
|
|
Pull nfsd bugfixes from Bruce Fields:
"Fixes for a new regression from the xdr encoding rewrite, and a
delegation problem we've had for a while (made somewhat more annoying
by the vfs delegation support added in 3.13)"
* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
NFSD: fix bug for readdir of pseudofs
NFSD: Don't hand out delegations for 30 seconds after recalling them.
|
|
In commit 629c9a8fd0bbdfc6d702526b327470166ec39c6b (drivers: net: cpsw: Add
default vlan for dual emac case also), api cpsw_add_default_vlan() also
changes the port vlan which is required to seperate the ports which results
in the following behavior
In Dual EMAC mode, when both the Etnernet connected is connected to same
switch, it creates a loop in the switch and when a broadcast packet is
received it is forwarded to the other port which stalls the whole switch
and needs a reset/power cycle to the switch to recover. So intead of using
the api, add only the default VLAN entry in dual EMAC case.
Cc: Yegor Yefremov <[email protected]>
Cc: Felipe Balbi <[email protected]>
Signed-off-by: Mugunthan V N <[email protected]>
Tested-by: Yegor Yefremov <[email protected]>
Tested-by: Felipe Balbi <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
David Vrabel says:
====================
xen-netfront: fix resume regressions in 3.16-rc1
The introduction of multi-queue support to xen-netfront in 3.16-rc1,
broke resume/migration.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
When reconnecting to the backend (after a resume/migration, for example),
a different number of queues may be required (since the guest may have
moved to a different host with different capabilities). During the
reconnection the old queues are torn down and new ones created.
Introduce xennet_create_queues() and xennet_destroy_queues() that fixes
three bugs during the reconnection.
- The old info->queues was leaked.
- The old queue's napi instances were not deleted.
- The new queue's napi instances were left disabled (which meant no
packets could be received).
The xennet_destroy_queues() calls is deferred until the reconnection
instead of the disconnection (in xennet_disconnect_backend()) because
napi_disable() might sleep.
Signed-off-by: David Vrabel <[email protected]>
Reviewed-by: Wei Liu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
xennet_disconnect_backend() was not correctly iterating over all the
queues.
Signed-off-by: David Vrabel <[email protected]>
Reviewed-by: Wei Liu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Daniel Mack says:
====================
Handle stuck TX queue bug in AT8030 PHY
These three small patches circument a hardware bug in AT8030 PHYs that
leads to stuck TX FIFO queues when the link goes away while there are
pending patches in der outbound queue. This bug has been confirmed by
the vendor, and their only proposed fix is to apply a hardware reset
every time the link goes down.
v1 -> v2:
* Rename phy device callback from adjust_state to link_change_notify
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The AT8030 will enter a FIFO error mode if a packet is transmitted while
the cable is unplugged. This hardware issue is acknowledged by the
vendor, and the only proposed solution is to conduct a hardware reset
via the external pin each time the link goes down. There is apparantly
no way to fix up the state via the register set.
This patch adds support for reading a 'reset-gpios' property from the DT
node of the PHY. If present, this gpio is used to apply a hardware reset
each time a 'link down' condition is detected. All relevant registers
are read out before, and written back after the reset cycle.
Doing this every time the link goes down might seem like overkill, but
there is unfortunately no way of figuring out whether the PHY is in
such a lock-up state. Hence, this is the only way of reliably fixing up
things.
Signed-off-by: Daniel Mack <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This removes magic values from two tables and also allows us to match
against specific PHY models at runtime.
Signed-off-by: Daniel Mack <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add a notify callback to inform phy drivers when the core is about to
do its link adjustment. No change for drivers that do not implement
this callback.
Signed-off-by: Daniel Mack <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
skb_cow called in vlan_reorder_header does not free the skb when it failed,
and vlan_reorder_header returns NULL to reset original skb when it is called
in vlan_untag, lead to a memory leak.
Signed-off-by: Li RongQing <[email protected]>
Acked-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"This is larger than usual: the main reason are the ARM symbol lookup
speedups that came in late and were hard to resist.
There's also a kprobes fix and various tooling fixes, plus the minimal
re-enablement of the mmap2 support interface"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/kprobes: Fix build errors and blacklist context_track_user
perf tests: Add test for closing dso objects on EMFILE error
perf tests: Add test for caching dso file descriptors
perf tests: Allow reuse of test_file function
perf tests: Spawn child for each test
perf tools: Add dso__data_* interface descriptons
perf tools: Allow to close dso fd in case of open failure
perf tools: Add file size check and factor dso__data_read_offset
perf tools: Cache dso data file descriptor
perf tools: Add global count of opened dso objects
perf tools: Add global list of opened dso objects
perf tools: Add data_fd into dso object
perf tools: Separate dso data related variables
perf tools: Cache register accesses for unwind processing
perf record: Fix to honor user freq/interval properly
perf timechart: Reflow documentation
perf probe: Improve error messages in --line option
perf probe: Improve an error message of perf probe --vars mode
perf probe: Show error code and description in verbose mode
perf probe: Improve error message for unknown member of data structure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rtmutex fixes from Thomas Gleixner:
"Another three patches to make the rtmutex code more robust. That's
the last urgent fallout from the big futex/rtmutex investigation"
* 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rtmutex: Plug slow unlock race
rtmutex: Detect changes in the pi lock chain
rtmutex: Handle deadlock detection smarter
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"A couple of bug fixes, a debug change for qdio, an update for the
default config, and one small extension.
The watchdog module based on diagnose 0x288 is converted to the
watchdog API and it now works under LPAR as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ccwgroup: use ccwgroup_ungroup wrapper
s390/ccwgroup: fix an uninitialized return code
s390/ccwgroup: obtain extra reference for asynchronous processing
qdio: Keep device-specific dbf entries
s390/compat: correct ucontext layout for high gprs
s390/cio: set device name as early as possible
s390: update default configuration
s390: avoid format strings leaking into names
s390/airq: silence lockdep warning
s390/watchdog: add support for LPAR operation (diag288)
s390/watchdog: use watchdog API
s390/sclp_vt220: Enable ASCII console per default
s390/qdio: replace shift loop by ilog2
s390/cio: silence lockdep warning
s390/uaccess: always load the kernel ASCE after task switch
s390/ap_bus: Make modules parameters visible in sysfs
|
|
Pull UniCore32 bug fixes from Guan Xuetao:
"This includes bugfixes to make unicore32 successfully build under
defconfig, and some changes for allmodconfig (though not finished)"
* tag 'for-linus' of git://github.com/gxt/linux:
unicore32: Remove ARCH_HAS_CPUFREQ config option
UniCore32: Change git tree location information in MAINTAINERS
arch: unicore32: ksyms: export '__cpuc_coherent_kern_range' to avoid compiling failure
arch: unicore32: ksyms: export 'pm_power_off' to avoid compiling failure.
arch: unicore32: ksyms: export additional find_first_*() to avoid compiling failure
arch:unicore32:mm: add devmem_is_allowed() to support STRICT_DEVMEM
unicore32: include: asm: add missing ')' for PAGE_* macros in pgtable.h
arch/unicore32/kernel/setup.c: add generic 'screen_info' to avoid compiling failure
drivers: scsi: mvsas: fix compiling issue by adding 'MVS_' for "enum pci_interrupt_cause"
arch: unicore32: kernel: ksyms: remove 'bswapsi2' and 'muldi3' to avoid compiling failure
arch/unicore32/kernel/ksyms.c: remove 2 export symbols to avoid compiling failure
drivers/rtc/rtc-puv3.c: remove "&dev->" for typo issue MIME-Version: 1.0
drivers/rtc/rtc-puv3.c: use dev_dbg() instead of dev_debug() for typo issue
arch/unicore32/include/asm/io.h: add readl_relaxed() generic definition
arch/unicore32/include/asm/ptrace.h: add generic definition for profile_pc()
arch/unicore32/mm/alignment.c: include "asm/pgtable.h" to avoid compiling error
arch/unicore32/kernel/clock.c: add readl() and writel() for 'PM_' macros
arch/unicore32/kernel/module.c: use __vmalloc_node_range() instead of __vmalloc_area()
arch/unicore32/kernel/ksyms.c: remove several undefined exported symbols
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver fixes from Greg KH:
"Here are 3 patches, one a revert of the UIO patch you objected to in
3.16-rc1 and that no one wanted to defend, a w1 driver bugfix, and a
MAINTAINERS update for the vmware balloon driver.
All of these, except for the MAINTAINERS update which just got added,
have been in linux-next just fine"
* tag 'char-misc-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: add entry for VMware Balloon driver
w1: mxc_w1: Fix incorrect "presence" status
Revert "uio: fix vma io range check in mmap"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few fixes for staging and iio drivers that resolve issues
reported in 3.16-rc1.
All have been in linux-next just fine"
* tag 'staging-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
imx-drm: parallel-display: Fix DPMS default state.
staging: android: timed_output: fix use after free of dev
staging: comedi: addi_apci_1564: add addi_watchdog dependency
staging: rtl8723au: Reference correct firmwarefiles with MODULE_FIRMWARE()
staging: rtl8723au: Request correct firmware file for A-cut parts
iio: adc: checking for NULL instead of IS_ERR() in probe
iio: adc: at91: signedness bug in at91_adc_get_trigger_value_by_name()
iio: mxs-lradc: fix divider
iio: Fix endianness issue in ak8975_read_axis()
staging/iio: IIO_SIMPLE_DUMMY_BUFFER neds IIO_BUFFER
twl4030-madc: Request processed values in twl4030_get_madc_conversion
staging: iio: tsl2x7x_core: fix proximity treshold
iio: Fix two mpl3115 issues in measurement conversion
iio: hid-sensors: Get feature report from sensor hub after changing power state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial bugfixes from Greg KH:
"Here are some tty / serial driver bugfixes for 3.16-rc2 that resolve
some reported issues. The samsung driver build error itself has been
reported by a bunch of people, sorry about that one. The others are
all tiny and everyone seems to like them in linux-next so far"
* tag 'tty-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty/serial: fix 8250 early console option passing to regular console
tty: Correct INPCK handling
serial: Fix IGNBRK handling
serial: samsung: Fix build error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.16-rc2 that resolve some reported
issues. All of these have been in linux-next for a while with no
problems"
* tag 'usb-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbtest: add a timeout for scatter-gather tests
USB: EHCI: avoid BIOS handover on the HASEE E200
usb: fix hub-port pm_runtime_enable() vs runtime pm transitions
usb: quiet peer failure warning, disable poweroff
usb: improve "not suspended yet" message in hub_suspend()
xhci: Fix sleeping with IRQs disabled in xhci_stop_device()
usb: fix ->update_hub_device() vs hdev->maxchild
|
|
On exynos mcpm systems the firmware is hardcoded to jump to an address
in SRAM (0x02073000) when secondary CPUs come up. By default the
firmware puts a bunch of code at that location. That code expects the
kernel to fill in a few slots with addresses that it uses to jump back
to the kernel's entry point for secondary CPUs.
Originally (on prerelease hardware) this firmware code contained a
bunch of workarounds to deal with boot ROM bugs. However on all
shipped hardware we simply use this code to redirect to a kernel
function for bringing up the CPUs.
Let's stop relying on the code provided by the bootloader and just
plumb in our own (simple) code jump to the kernel. This has the nice
benefit of fixing problems due to the fact that older bootloaders
(like the one shipped on the Samsung Chromebook 2) might have put
slightly different code into this location.
Once suspend/resume is implemented for systems using exynos-mcpm we'll
need to make sure we reinstall our fixed up code after resume. ...but
that's not anything new since IRAM (and thus the address of the
mcpm_entry_point) is lost across suspend/resume anyway.
Signed-off-by: Doug Anderson <[email protected]>
Acked-by: Kevin Hilman <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
Acked-by: Nicolas Pitre <[email protected]>
Signed-off-by: Kukjin Kim <[email protected]>
|
|
We use regmap regulator ops to enable/disable and check if regulator
is enabled for various SMPS. However, these depend on valid
enable_reg, enable_mask and enable_value in regulator descriptor.
Currently we do not populate these for SMPS other than SMPS10, this
results in spurious results as regmap assumes that the values are
valid and ends up reading register 0x0 RTC:SECONDS_REG on Palmas
variants that do have RTC! To fix this, we update proper parameters
for the descriptor fields.
Further, we want to ensure the behavior consistent with logic
prior to commit dbabd624d4eec50b6, where, once you do a set_mode,
enable/disable ensure the logic remains consistent and configures
Palmas to the configuration that we set with set_mode (since the
configuration register is common). To do this, we can rely on the
regulator core's regulator_register behavior where the regulator
descriptor pointer provided by the regulator driver is stored. (no
reallocation and copy is done). This lets us update the enable_value
post registration, to remain consistent with the mode we configure as
part of set_mode.
Fixes: dbabd624d4eec50b6 ("regulator: palmas: Reemove open coded functions with helper functions")
Reported-by: Alexandre Courbot <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
Tested-by: Alexandre Courbot <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
This patch moves the devm_spi_register_master below the initialization of the
runtime_pm. If done in the wrong order, the spi_register_master fails if any
probed slave devices issue SPI transactions.
Signed-off-by: Andy Gross <[email protected]>
Acked-by: Ivan T. Ivanov <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
|
|
The following commit:
89d7e5c mmc: sdhci-esdhc-imx: add runtime pm support
has the effect of also disabling the hardware card detect
in runtime pm.
We switch to GPIO based detection to avoid this issue.
This patch is based on:
ARM: dts: imx51-babbage: Fix esdhc setup
Signed-off-by: Denis Carikli <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Since commit 89d7e5c13122 (mmc: sdhci-esdhc-imx: add runtime pm
support), controller based card detection / write protection is not
supported anymore by esdhc driver. Let's use GPIO for CD/WP on esdhc1
instead.
While at it, fix cd gpio polarity for esdhc2. This is wrong and
currently only works because the imx esdhc driver ignores the polarity.
Signed-off-by: Sascha Hauer <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Move the display {} node out of the soc {} node . This just aligns
the DT with other boards, there is no functional change.
Signed-off-by: Marek Vasut <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Currently the __field() macro in TRACE_EVENT is only good for primitive
values, such as integers and pointers, but it fails on complex data types
such as structures or unions. This is because the __field() macro
determines if the variable is signed or not with the test of:
(((type)(-1)) < (type)1)
Unfortunately, that fails when type is a structure.
Since trace events should support structures as fields a new macro
is created for such a case called __field_struct() which acts exactly
the same as __field() does but it does not do the signed type check
and just uses a constant false for that answer.
Cc: Tony Luck <[email protected]>
Signed-off-by: Steven Rostedt <[email protected]>
|
|
syscall_regfunc() ignores the kernel threads because "it has no effect",
see cc3b13c1 "Don't trace kernel thread syscalls" which added this check.
However, this means that a user-space task spawned by call_usermodehelper()
will run without TIF_SYSCALL_TRACEPOINT if sys_tracepoint_refcount != 0.
Remove this check. The unnecessary report from ret_from_fork path mentioned
by cc3b13c1 is no longer possible, see See commit fb45550d76bb5 "make sure
that kernel_thread() callbacks call do_exit() themselves".
A kernel_thread() callback can only return and take the int_ret_from_sys_call
path after do_execve() succeeds, otherwise the kernel will crash. But in this
case it is no longer a kernel thread and thus is needs TIF_SYSCALL_TRACEPOINT.
Link: http://lkml.kernel.org/p/[email protected]
Signed-off-by: Oleg Nesterov <[email protected]>
Signed-off-by: Steven Rostedt <[email protected]>
|
|
for_each_process_thread()
1. Remove _irqsafe from syscall_regfunc/syscall_unregfunc,
read_lock(tasklist) doesn't need to disable irqs.
2. Change this code to avoid the deprecated do_each_thread()
and use for_each_process_thread() (stolen from the patch
from Frederic).
3. Change syscall_regfunc() to check PF_KTHREAD to skip
the kernel threads, ->mm != NULL is the common mistake.
Note: probably this check should be simply removed, needs
another patch.
[[email protected]: s/do_each_thread/for_each_process_thread/]
Link: http://lkml.kernel.org/p/[email protected]
Signed-off-by: Oleg Nesterov <[email protected]>
Signed-off-by: Steven Rostedt <[email protected]>
|
|
syscall_regfunc() and syscall_unregfunc() should set/clear
TIF_SYSCALL_TRACEPOINT system-wide, but do_each_thread() can race
with copy_process() and miss the new child which was not added to
the process/thread lists yet.
Change copy_process() to update the child's TIF_SYSCALL_TRACEPOINT
under tasklist.
Link: http://lkml.kernel.org/p/[email protected]
Cc: [email protected] # 2.6.33
Fixes: a871bd33a6c0 "tracing: Add syscall tracepoints"
Acked-by: Frederic Weisbecker <[email protected]>
Acked-by: Paul E. McKenney <[email protected]>
Signed-off-by: Oleg Nesterov <[email protected]>
Signed-off-by: Steven Rostedt <[email protected]>
|
|
The "port" node was misplaced in the original patch, therefore making
the LCD dysfunctional on this board. Fix this by moving the "port" DT
node into the "display {}" node.
Signed-off-by: Marek Vasut <[email protected]>
Acked-by: Philipp Zabel <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
On Marvell Armada platforms, the PMSU (Power Management Service Unit)
controls a number of power management related activities, needed for
things like suspend/resume, CPU hotplug, cpuidle or even simply SMP.
Since cpuidle support was added for Armada XP, the pmsu.c file in
arch/arm/mach-mvebu/ calls the cpu_suspend() and cpu_resume() ARM
functions, which are only available when
CONFIG_ARM_CPU_SUSPEND=y. Therefore, configurations that have
CONFIG_ARM_CPU_SUSPEND disabled due to PM_SLEEP being disabled no
longer build properly, due to undefined references to cpu_suspend()
and cpu_resume().
To fix this, this patch simply ensures CONFIG_ARM_CPU_SUSPEND is
always enabled for Marvell EBU v7 platforms. Doing things in a more
fine-grained way would require a lot of #ifdef-ery in pmsu.c to
isolate the parts that use cpu_suspend()/cpu_resume(), and those parts
would anyway have been needed as soon as either one of suspend/resume,
CPU hotplug or cpuidle was enabled.
Reported-by: Ezequiel Garcia <[email protected]>
Signed-off-by: Thomas Petazzoni <[email protected]>
Link: https://lkml.kernel.org/r/1402488397-31381-1-git-send-email-thomas.petazzoni@free-electrons.com
Acked-by: Ezequiel Garcia <[email protected]>
Signed-off-by: Jason Cooper <[email protected]>
|
|
Currently the mvebu boards need to detect the SoC revision in order to apply
some quirks needed to workaround issues found on I2C and thermal controllers
present only in very early SoC.
This detection requires PCI address translation to work, so we need to
explicitly select OF_ADDRESS_PCI.
This can be considered a partial revert of the following commit, that
wrongly removed the option selection:
commit 55400f3a1f89e39761f45c19f6e4235a329c400b
Author: Rob Herring <[email protected]>
Date: Tue Apr 22 14:15:52 2014 -0500
ARM: mvebu: clean-up unneeded kconfig selects
Signed-off-by: Ezequiel Garcia <[email protected]>
Link: https://lkml.kernel.org/r/1402347165-19988-1-git-send-email-ezequiel.garcia@free-electrons.com
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Jason Cooper <[email protected]>
|
|
With this change, doing 'make vdso_install' and telling gdb:
set debug-file-directory /lib/modules/KVER/vdso
will enable vdso debugging with symbols. This is useful for
testing, but kernel RPM builds will probably want to manually delete
these symlinks or otherwise do something sensible when they strip
the vdso/*.so files.
If ld does not support --build-id, then the symlinks will not be
created.
Note that kernel packagers that use vdso_install may need to adjust
their packaging scripts to accomdate this change. For example,
Fedora's scripts create build-id symlinks themselves in a different
location, so the spec should probably be updated to remove the
symlinks created by make vdso_install.
Signed-off-by: Andy Lutomirski <[email protected]>
Link: http://lkml.kernel.org/r/a424b189ce3ced85fe1e82d032a20e765e0fe0d3.1403291930.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <[email protected]>
|
|
In 2.6.29 io_tlb_orig_addr[] got converted from storing virtual addresses
to storing physical ones. While checking virtual addresses against NULL
is a legitimate thing to catch invalid entries, checking physical ones
against zero isn't: There's no guarantee that PFN 0 is reserved on a
particular platform.
Since it is unclear whether the check in swiotlb_tbl_unmap_single() is
actually needed, retain it but check against a guaranteed invalid physical
address. This requires setting up the array in a suitable fashion. And
since the original code failed to invalidate array entries when regions
get unmapped, this is being fixed at once along with adding a similar
check to swiotlb_tbl_sync_single().
Obviously the less intrusive change would be to simply drop the check in
swiotlb_tbl_unmap_single().
Signed-off-by: Jan Beulich <[email protected]>
Signed-off-by: Konrad Rzeszutek Wilk <[email protected]>
|
|
Signed-off-by: Dmitry Torokhov <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Commit e79df31 introduced mmu_notifer_count to protect
against parallel mmu_notifier_invalidate_range_start/end
calls. The patch left a small race condition when
invalidate_range_end() races with a new
invalidate_range_start() the empty page-table may be
reverted leading to stale TLB entries in the IOMMU and the
device. Use a spin_lock instead of just an atomic variable
to eliminate the race.
Signed-off-by: Joerg Roedel <[email protected]>
|
|
Since commit 39b9004d1f (gpu: ipu-v3: Move i.MX IPUv3 core driver out of
staging) the ipuv3 core driver is no longer built bey default.
Select CONFIG_IMX_IPUV3_CORE so that the core ipuv3 code can be built again.
Signed-off-by: Fabio Estevam <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Function dmar_iommu_notify_scope_dev() makes a wrong assumption that
there's one RMRR for each PCI device at most, which causes DMA failure
on some HP platforms. So enhance dmar_iommu_notify_scope_dev() to
handle multiple RMRRs for the same PCI device.
Fixbug: https://bugzilla.novell.com/show_bug.cgi?id=879482
Cc: <[email protected]> # 3.15
Reported-by: Tom Mingarelli <[email protected]>
Tested-by: Linda Knippers <[email protected]>
Signed-off-by: Jiang Liu <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
|
|
Commit ca8f0b0a545f ("ARM: ensure C page table setup code follows
assembly code") did what it said on the tin, but some of the older
CPU code omitted the default cache policy from their files. This
results in the kernel running with the caches disabled. Fix this
for ARM925.
Reported-by: Aaro Koskinen <[email protected]>
Signed-off-by: Russell King <[email protected]>
|
|
This patch adds QCOM GSBI config option to multi_v7_defconfig. Serial
driver on QCOM APQ8064 depends on GSBI driver, so without this patch
there is no serial console on IF6410 board using multi_v7_defconfig.
Signed-off-by: Srinivas Kandagatla <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.stlinux.com/devel/kernel/linux-sti into fixes
Merge "STi: DT fixes for v3.16" from Maxime Coquelin:
Couple of DT fixes for STi platform issues discovered on V3.16-rc1.
The fixes included are:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase.
* tag 'sti-fixes-for-v3.16-rc1' of git://git.stlinux.com/devel/kernel/linux-sti: (2963 commits)
ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
ARM: STi: DT: Properly define sti-ethclk & stmmaceth for stih415/6
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are fixes mostly (ia64 regression related to the ACPI
enumeration of devices, cpufreq regressions, fix for I2C controllers
included in Intel SoCs, mvebu cpuidle driver fix related to sysfs)
plus additional kernel command line arguments from Kees to make it
possible to build kernel images with hibernation and the kernel
address space randomization included simultaneously, a new ACPI
battery driver quirk for a system with a broken BIOS and a couple of
ACPI core cleanups.
Specifics:
- Fix for an ia64 regression introduced during the 3.11 cycle by a
commit that modified the hardware initialization ordering and made
device discovery fail on some systems.
- Fix for a build problem on systems where the cpufreq-cpu0 driver is
built-in and the cpu-thermal driver is modular from Arnd Bergmann.
- Fix for a recently introduced computational mistake in the
intel_pstate driver that leads to excessive rounding errors from
Doug Smythies.
- Fix for a failure code path in cpufreq_update_policy() that fails
to unlock the locks acquired previously from Aaron Plattner.
- Fix for the cpuidle mvebu driver to use shorter state names which
will prevent the sysfs interface from returning mangled strings.
From Gregory Clement.
- ACPI LPSS driver fix to make sure that the I2C controllers included
in BayTrail SoCs are not held in the reset state while they are
being probed from Mika Westerberg.
- New kernel command line arguments making it possible to build
kernel images with hibernation and kASLR included at the same time
and to select which of them will be used via the command line (they
are still functionally mutually exclusive, though). From Kees
Cook.
- ACPI battery driver quirk for Acer Aspire V5-573G that fails to
send battery status change notifications timely from Alexander
Mezin.
- Two ACPI core cleanups from Christoph Jaeger and Fabian Frederick"
* tag 'pm+acpi-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: mvebu: Fix the name of the states
cpufreq: unlock when failing cpufreq_update_policy()
intel_pstate: Correct rounding in busy calculation
ACPI: use kstrto*() instead of simple_strto*()
ACPI / processor replace __attribute__((packed)) by __packed
ACPI / battery: add quirk for Acer Aspire V5-573G
ACPI / battery: use callback for setting up quirks
ACPI / LPSS: Take I2C host controllers out of reset
x86, kaslr: boot-time selectable with hibernation
PM / hibernate: introduce "nohibernate" boot parameter
cpufreq: cpufreq-cpu0: fix CPU_THERMAL dependency
ACPI / ia64 / sba_iommu: Restore the working initialization ordering
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The significant part here is a few security fixes for ALSA core
control API by Lars. Besides that, there are a few fixes for ASoC
sigmadsp (again by Lars) for building properly, and small fixes for
ASoC rsnd, MMP, PXA and FSL, in addition to a fix for bogus WARNING in
i915/HD-audio binding"
* tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: control: Make sure that id->index does not overflow
ALSA: control: Handle numid overflow
ALSA: control: Don't access controls outside of protected regions
ALSA: control: Fix replacing user controls
ALSA: control: Protect user controls against concurrent access
drm/i915, HD-audio: Don't continue probing when nomodeset is given
ASoC: fsl: Fix build problem
ASoC: rsnd: fixup index of src/dst mod when capture
ASoC: fsl_spdif: Fix integer overflow when calculating divisors
ASoC: fsl_spdif: Fix incorrect usage of regmap_read()
ASoC: dapm: Make sure register value is in sync with DAPM kcontrol state
ASoC: sigmadsp: Split regmap and I2C support into separate modules
ASoC: MMP audio needs sram support
ASoC: pxa: add I2C dependencies as needed
|
|
Pull drm fixes from Dave Airlie:
"This looks bigger than it is, as one of the nouveau firmware fixes
("drm/gf100-/gr: report class data to host on fwmthd failure")
regenerates a bunch of the firmware files after changing the assembly
by a few lines, without that, its more of a
36 files changed, 370 insertions(+), 129 deletions(-)
It contains some vt.c fixes acked by Greg, for rare hard hangs on i915
loading, that also fixes hangs on reload and spurious register write
errors.
drm core: one fix for uninit memory
nouveau: displayport rework caused a few regressions, Ben has been
fixing them as the appear, along with some other fixes
radeon: pageflipping regression fix, deep color fix, mode validation
fixes
i915: fbc disable, vga console kick off, backlight fix, divide-by-zero
fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
drm: fix uninitialized acquire_ctx fields (v2)
drm/radeon: Fix radeon_irq_kms_pflip_irq_get/put() imbalance
Revert "drm/radeon: remove drm_vblank_get|put from pflip handling"
drm/radeon: improve dvi_mode_valid
drm/radeon: update mode_valid testing for DP
drm/radeon: Use dce5/6 hdmi deep color clock setup also on dce8+
drm/nouveau/disp: fix oops in destructor with headless cards
drm/gf117/i2c: no aux channels on this chipset
drm/nouveau/doc: update the thermal documentation
drm/nouveau/pwr: fix typo in fifo wrap handling
drm/nv50/disp: fix a potential oops in supervisor handling
drm/nouveau/disp/dp: don't touch link config after success
drm/nouveau/kms: reference vblank for crtc during pageflip.
drm/gk104/fb/ram: fixups from an earlier search+replace
drm/nv50/gr: remove an unneeded write while initialising PGRAPH
drm/nv50/gr: fix overlap while zeroing zcull regions
drm/gf100-/gr: report class data to host on fwmthd failure
drm/gk104/ibus: increase various random timeouts
drm/gk104/clk: only touch divider for mode we'll be using
drm/radeon: Bypass hw lut's for > 8 bpc framebuffer scanout.
...
|