aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2020-02-13drm/hisilicon/hibmc: add gamma_set functionZhihui Chen2-0/+42
Add gamma_set function, and we can also use it to adjust the brightness of the display. Signed-off-by: Zhihui Chen <[email protected]> Signed-off-by: Xinliang Liu <[email protected]> Acked-by: Xinliang Liu <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2020-02-13drm/hisilicon/hibmc: add DPMS on/off functionZhihui Chen2-0/+22
add DPMS function to turn on/off signal of monitor Signed-off-by: Zhihui Chen <[email protected]> Signed-off-by: Xinliang Liu <[email protected]> Acked-by: Xinliang Liu <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2020-02-13drm/hisilicon/hibmc: fix 'xset dpms force off' failZhihui Chen1-0/+3
both crtc_state->adjusted_mode.hdisplay and crtc_state->adjusted_mode.vdisplay are 0 when switch dpms off, return -EINVAL cause switch dpms off fail. Signed-off-by: Zhihui Chen <[email protected]> Signed-off-by: Xinliang Liu <[email protected]> Acked-by: Xinliang Liu <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2020-02-13drm/bridge: ti-sn65dsi86: Avoid invalid ratesDouglas Anderson1-25/+75
Based on work by Bjorn Andersson <[email protected]>, Jeffrey Hugo <[email protected]>, and Rob Clark <[email protected]>. Let's read the SUPPORTED_LINK_RATES and/or MAX_LINK_RATE (depending on the eDP version of the sink) to figure out what eDP rates are supported and pick the ideal one. NOTE: I have only personally tested this code on eDP panels that are 1.3 or older. Code reading SUPPORTED_LINK_RATES for DP 1.4+ was tested by hacking the code to pretend that a table was there. Signed-off-by: Douglas Anderson <[email protected]> Reviewed-by: Bjorn Andersson <[email protected]> Signed-off-by: Neil Armstrong <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.9.Ib59207b66db377380d13748752d6fce5596462c5@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Train at faster rates if slower ones failDouglas Anderson1-11/+60
If we fail training at a lower DP link rate let's now keep trying until we run out of rates to try. Basically the algorithm here is to start at the link rate that is the theoretical minimum and then slowly bump up until we run out of rates or hit the max rate of the sink. We query the sink using a DPCD read. This is, in fact, important in practice. Specifically at least one panel hooked up to the bridge (AUO B116XAK01) had a theoretical min rate more than 1.62 GHz (if run at 24 bpp) and fails to train at the next rate (2.16 GHz). It would train at 2.7 GHz, though. Signed-off-by: Douglas Anderson <[email protected]> Tested-by: Rob Clark <[email protected]> Reviewed-by: Rob Clark <[email protected]> Reviewed-by: Bjorn Andersson <[email protected]> Signed-off-by: Neil Armstrong <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.8.I251add713bc5c97225200894ab110ea9183434fd@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Group DP link training bits in a functionDouglas Anderson1-34/+52
We'll re-organize the ti_sn_bridge_enable() function a bit to group together all the parts relating to link training and split them into a sub-function. This is not intended to have any functional change and is in preparation for trying link training several times at different rates. One small side effect here is that if link training fails we'll now leave the DP PLL disabled, but that seems like a sane thing to do. Signed-off-by: Douglas Anderson <[email protected]> Tested-by: Rob Clark <[email protected]> Reviewed-by: Rob Clark <[email protected]> Reviewed-by: Bjorn Andersson <[email protected]> Signed-off-by: Neil Armstrong <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.7.I1fc75ad11db9048ef08cfe1ab7322753d9a219c7@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Use 18-bit DP if we canDouglas Anderson1-9/+18
The current bridge driver always forced us to use 24 bits per pixel over the DP link. This is a waste if you are hooked up to a panel that only supports 6 bits per color or fewer, since in that case you can run at 18 bits per pixel and thus end up at a lower DP clock rate. Let's support this. While at it, let's clean up the math in the function to avoid rounding errors (and round in the correct direction when we have to round). Numbers are sufficiently small (because mode->clock is in kHz) that we don't need to worry about integer overflow. Signed-off-by: Douglas Anderson <[email protected]> Tested-by: Rob Clark <[email protected]> Reviewed-by: Rob Clark <[email protected]> Reviewed-by: Bjorn Andersson <[email protected]> [narmstrong: s/ran/can/] Signed-off-by: Neil Armstrong <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.6.Iaf8d698f4e5253d658ae283d2fd07268076a7c27@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Read num lanes from the DP sinkDouglas Anderson1-2/+30
At least one panel hooked up to the bridge (AUO B116XAK01) only supports 1 lane of DP. Let's read this information and stop hardcoding 4 DP lanes. Signed-off-by: Douglas Anderson <[email protected]> Tested-by: Rob Clark <[email protected]> Reviewed-by: Rob Clark <[email protected]> Reviewed-by: Bjorn Andersson <[email protected]> Signed-off-by: Neil Armstrong <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.5.Idbd0051d0de53f7e9d18a291ea33011c0854fcc6@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Config number of DP lanes Mo' BettaDouglas Anderson1-1/+1
The driver used to say that the value to program into bridge register 0x93 was dp_lanes - 1. Looking at the datasheet for the bridge, this is wrong. The data sheet says: * 1 = 1 lane * 2 = 2 lanes * 3 = 4 lanes A more proper way to express this encoding is min(dp_lanes, 3). At the moment this change has zero effect because we've hardcoded the number of DP lanes to 4. ...and (4 - 1) == min(4, 3). How fortunate! ...but soon we'll stop hardcoding the number of lanes. Signed-off-by: Douglas Anderson <[email protected]> Tested-by: Rob Clark <[email protected]> Reviewed-by: Rob Clark <[email protected]> Reviewed-by: Bjorn Andersson <[email protected]> Signed-off-by: Neil Armstrong <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.4.If3e2d0493e7b6e8b510ea90d8724ff760379b3ba@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Don't use MIPI variables for DP linkDouglas Anderson1-6/+12
The ti-sn65dsi86 is a bridge from MIPI to DP and thus has two links: the MIPI link and the DP link. The two links do not need to have the same format or number of lanes. Stop using MIPI variables when talking about the DP link. This has zero functional change because: * currently we are hardcoding the MIPI link as unpacked RGB888 which requires 24 bits and currently we are not changing the DP link rate from the bridge's default of 8 bits per pixel. * currently we are hardcoding both the MIPI and DP as being 4 lanes. This is all in prep for fixing some of the above. Signed-off-by: Douglas Anderson <[email protected]> Tested-by: Rob Clark <[email protected]> Reviewed-by: Rob Clark <[email protected]> Reviewed-by: Bjorn Andersson <[email protected]> Signed-off-by: Neil Armstrong <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.3.Ia6e05f4961adb0d4a0d32ba769dd7781ee8db431@changeid
2020-02-13drm/bridge: ti-sn65dsi86: zero is never greater than an unsigned intDouglas Anderson1-1/+1
When we iterate over ti_sn_bridge_dp_rate_lut, there's no reason to start at index 0 which always contains the value 0. 0 is not a valid link rate. This change should have no real effect but is a small cleanup. Signed-off-by: Douglas Anderson <[email protected]> Tested-by: Rob Clark <[email protected]> Reviewed-by: Rob Clark <[email protected]> Reviewed-by: Bjorn Andersson <[email protected]> Signed-off-by: Neil Armstrong <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.2.Id445d0057bedcb0a190009e0706e9254c2fd48eb@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Split the setting of the dp and dsi ratesDouglas Anderson1-10/+23
These two things were in one function. Split into two. This looks like it's duplicating some code, but don't worry. This is is just in preparation for future changes. This is intended to have zero functional change and will just make future patches easier to understand. Signed-off-by: Douglas Anderson <[email protected]> Tested-by: Rob Clark <[email protected]> Reviewed-by: Rob Clark <[email protected]> Reviewed-by: Bjorn Andersson <[email protected]> Signed-off-by: Neil Armstrong <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.1.Icb765d5799e9651e5249c0c27627ba33a9e411cf@changeid
2020-02-13ALSA: usb-audio: Add clock validity quirk for Denon MC7000/MCX8000Alexander Tsoy3-32/+66
It should be safe to ignore clock validity check result if the following conditions are met: - only one single sample rate is supported; - the terminal is directly connected to the clock source; - the clock type is internal. This is to deal with some Denon DJ controllers that always reports that clock is invalid. Tested-by: Tobias Oszlanyi <[email protected]> Signed-off-by: Alexander Tsoy <[email protected]> Cc: <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2020-02-12cifs: Fix mode output in debugging statementsFrank Sorenson3-4/+4
A number of the debug statements output file or directory mode in hex. Change these to print using octal. Signed-off-by: Frank Sorenson <[email protected]> Signed-off-by: Steve French <[email protected]>
2020-02-12io-wq: don't call kXalloc_node() with non-online nodeJens Axboe1-4/+18
Glauber reports a crash on init on a box he has: RIP: 0010:__alloc_pages_nodemask+0x132/0x340 Code: 18 01 75 04 41 80 ce 80 89 e8 48 8b 54 24 08 8b 74 24 1c c1 e8 0c 48 8b 3c 24 83 e0 01 88 44 24 20 48 85 d2 0f 85 74 01 00 00 <3b> 77 08 0f 82 6b 01 00 00 48 89 7c 24 10 89 ea 48 8b 07 b9 00 02 RSP: 0018:ffffb8be4d0b7c28 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000000000e8e8 RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000002080 RBP: 0000000000012cc0 R08: 0000000000000000 R09: 0000000000000002 R10: 0000000000000dc0 R11: ffff995c60400100 R12: 0000000000000000 R13: 0000000000012cc0 R14: 0000000000000001 R15: ffff995c60db00f0 FS: 00007f4d115ca900(0000) GS:ffff995c60d80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000002088 CR3: 00000017cca66002 CR4: 00000000007606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: alloc_slab_page+0x46/0x320 new_slab+0x9d/0x4e0 ___slab_alloc+0x507/0x6a0 ? io_wq_create+0xb4/0x2a0 __slab_alloc+0x1c/0x30 kmem_cache_alloc_node_trace+0xa6/0x260 io_wq_create+0xb4/0x2a0 io_uring_setup+0x97f/0xaa0 ? io_remove_personalities+0x30/0x30 ? io_poll_trigger_evfd+0x30/0x30 do_syscall_64+0x5b/0x1c0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7f4d116cb1ed which is due to the 'wqe' and 'worker' allocation being node affine. But it isn't valid to call the node affine allocation if the node isn't online. Setup structures for even offline nodes, as usual, but skip them in terms of thread setup to not waste resources. If the node isn't online, just alloc memory with NUMA_NO_NODE. Reported-by: Glauber Costa <[email protected]> Tested-by: Glauber Costa <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2020-02-12hwmon: (pmbus/xdpe12284) fix typo in compatible stringsJohan Hovold1-2/+2
Make sure that the driver compatible strings matches the binding by removing the space between the manufacturer and model. Fixes: aaafb7c8eb1c ("hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers") Cc: Vadim Pasternak <[email protected]> Signed-off-by: Johan Hovold <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Guenter Roeck <[email protected]>
2020-02-12linux/pipe_fs_i.h: fix kernel-doc warnings after @wait was splitRandy Dunlap1-1/+2
Fix kernel-doc warnings in struct pipe_inode_info after @wait was split into @rd_wait and @wr_wait. include/linux/pipe_fs_i.h:66: warning: Function parameter or member 'rd_wait' not described in 'pipe_inode_info' include/linux/pipe_fs_i.h:66: warning: Function parameter or member 'wr_wait' not described in 'pipe_inode_info' Fixes: 0ddad21d3e99 ("pipe: use exclusive waits when reading or writing") Signed-off-by: Randy Dunlap <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2020-02-12ice: Trivial fixesTony Nguyen11-29/+31
This is a collection of trivial fixes including fixing whitespace, typos, function headers, reverse Christmas tree, etc. Signed-off-by: Tony Nguyen <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: Use correct netif error functionBen Shelton1-1/+1
Use the correct netif_msg_[tx,rx]_error() function to determine whether to print the MDD event type. Signed-off-by: Ben Shelton <[email protected]> Signed-off-by: Tony Nguyen <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: Cleanup ice_vsi_alloc_q_vectorsAnirudh Venkataramanan1-8/+3
1. Remove local variable num_q_vectors and use vsi->num_q_vectors instead 2. Remove local variable pf and pass vsi->back to ice_pf_to_dev Signed-off-by: Anirudh Venkataramanan <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: Make print statements more compactAnirudh Venkataramanan8-227/+123
Formatting strings in print function calls (like dev_info, dev_err, etc.) can exceed 80 columns without making checkpatch unhappy. So remove newlines where applicable and make print statements more compact. Signed-off-by: Anirudh Venkataramanan <[email protected]> Signed-off-by: Tony Nguyen <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: Use ice_pf_to_devAnirudh Venkataramanan6-27/+27
Use ice_pf_to_dev(pf) instead of &pf->pdev->dev Use ice_pf_to_dev(vsi->back) instead of &vsi->back->pdev->dev When a pointer to the pf instance is available, use ice_pf_to_dev instead of ice_hw_to_dev Signed-off-by: Anirudh Venkataramanan <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: Remove possible null dereferenceTony Nguyen1-2/+0
Commit 1f45ebe0d8fb ("ice: add extra check for null Rx descriptor") moved the call to ice_construct_skb() under a null check as Coverity reported a possible use of null skb. However, the original call was not deleted, do so now. Fixes: 1f45ebe0d8fb ("ice: add extra check for null Rx descriptor") Reported-by: Bruce Allan <[email protected]> Signed-off-by: Tony Nguyen <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: update Unit Load Status bitmask to check after resetBruce Allan2-5/+18
After a reset the Unit Load Status bits in the GLNVM_ULD register to check for completion should be 0x7FF before continuing. Update the mask to check (minus the three reserved bits that are always set). Signed-off-by: Bruce Allan <[email protected]> Signed-off-by: Tony Nguyen <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: fix and consolidate logging of NVM/firmware version informationBruce Allan4-28/+13
Logging the firmware/NVM information during driver load is redundant since that information is also available via ethtool. Move the functionality found in ice_nvm_version_str() directly into ice_get_drvinfo() and remove calling the former and logging that info during driver probe. This also gets rid of a bug in ice_nvm_version_str() where it returns a pointer to a buffer which is free'ed when that function exits. Signed-off-by: Bruce Allan <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: Modify link message loggingAkeem G Abodunrin1-1/+1
This patch modifies link message logging to include "Full Duplex" and "Negotiated" for FEC, so as to distinguish it from "Requested" FEC. Signed-off-by: Akeem G Abodunrin <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: Remove CONFIG_PCI_IOV wrap in ice_set_pf_capsAnirudh Venkataramanan1-2/+0
Remove unnecessary CONFIG_PCI_IOV wrapping in ice_set_pf_caps. None of the data structures accessed within the block are wrapped with this flag. When CONFIG_PCI_IOV is undefined, pf->num_vfs_supported will be 0 anyway. Signed-off-by: Anirudh Venkataramanan <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: Remove ice_dev_onetime_setup()Brett Creeley4-20/+0
ice_dev_onetime_setup contains driver workarounds needed for firmware limitations. These issues have now been resolved in newer NVMs so remove the function. Signed-off-by: Brett Creeley <[email protected]> Signed-off-by: Tony Nguyen <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: Don't allow same value for Rx tail to be written twiceBrett Creeley1-1/+1
Currently we compare the value we are about to write to the Rx tail register with the previous value of next_to_use. The problem with this is we only write tail on 8 descriptor boundaries, but next_to_use is updated whenever we clean Rx descriptors. Fix this by comparing the value we are about to write to tail with the previously written tail value. This will prevent duplicate Rx tail bumps. Signed-off-by: Brett Creeley <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: display supported and advertised link modesPaul Greenwalt1-280/+2
Display all of the supported and advertised link modes based on the PHY capability with media. Displaying all supported modes is more informative then only displaying the current link mode. Signed-off-by: Paul Greenwalt <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: Fix switch between FW and SW LLDPDave Ertman1-5/+5
When switching between FW and SW LLDP mode, the number of configured TLV apps in the driver's DCB configuration is getting out of synch with what lldpad thinks is configured. This is causing a problem when shutting down lldpad. The cleanup is trying to delete TLV apps that are not defined in the kernel. Since the driver is keeping an accurate account of the apps defined, use the drivers number of apps to determine if there is an app to delete. If the number of apps is <= 1, then do not attempt to delete. Signed-off-by: Dave Ertman <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12ice: Fix DCB rebuild after resetDave Ertman2-53/+36
The function ice_dcb_rebuild had some logic flaws in it, and also didn't differentiate between FW and SW modes needs. For FW flow, the willing setting was being forced to OFF and left that way. Unwilling in DCB FW mode is not a supported model. Leave the config alone and use the return value from the set command to determine if setting the config was successful. The SW DCB flow does not need to need to register for MIB change events (as they are not used in SW mode). Use !is_sw_lldp checks to only perform FW specific task while in FW mode. Also adding a reapplication of the current DCB config after a link event. Some NVMs are not maintaining their DCB configs across link events. Signed-off-by: Dave Ertman <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2020-02-12docs: virt: guest-halt-polling.txt convert to ReSTMauro Carvalho Chehab2-3/+10
Due to some merge conflict, this file ended being alone under Documentation/virtual. The file itself is almost at ReST format. Just minor adjustments are needed: - Adjust title markup; - Adjust a list identation; - add a literal block markup; - Add some blank lines. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: review-checklist.txt: rename to ReSTMauro Carvalho Chehab2-0/+5
This file is already in ReST compatible format. So, rename it and add to the kvm's index.rst. While here, use the standard conversion for document titles. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Reviewed-by: Cornelia Huck <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: Convert timekeeping.txt to ReST formatMauro Carvalho Chehab2-95/+129
- Use document title and chapter markups; - Add markups for literal blocks; - Add markups for tables; - use :field: for field descriptions; - Add blank lines and adjust indentation. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: Convert s390-diag.txt to ReST formatMauro Carvalho Chehab2-5/+9
This file is almost in ReST format. Just one change was needed: - Add markups for a literal block and change its indentation. While here, use the standard markup for the document title. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Reviewed-by: Cornelia Huck <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: Convert ppc-pv.txt to ReST formatMauro Carvalho Chehab2-8/+19
- Use document title and chapter markups; - Add markups for tables; - Use list markups; - Add markups for literal blocks; - Add blank lines. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: Convert nested-vmx.txt to ReST formatMauro Carvalho Chehab2-16/+22
This file is almost in ReST format. Just a small set of changes were needed: - Add markups for lists; - Add markups for a literal block; - Adjust whitespaces. While here, use the standard markup for the document title. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: Convert mmu.txt to ReST formatMauro Carvalho Chehab2-14/+49
- Use document title and chapter markups; - Add markups for tables; - Add markups for literal blocks; - Add blank lines and adjust indentation. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: Convert locking.txt to ReST formatMauro Carvalho Chehab3-215/+244
- Use document title and chapter markups; - Add markups for literal blocks; - use :field: for field descriptions; - Add blank lines and adjust indentation. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: Convert hypercalls.txt to ReST formatMauro Carvalho Chehab2-56/+75
- Use document title and chapter markups; - Convert tables; - Add markups for literal blocks; - use :field: for field descriptions; - Add blank lines and adjust indentation Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: arm/psci.txt: convert to ReSTMauro Carvalho Chehab2-15/+32
- Add a title for the document; - Adjust whitespaces for it to be properly formatted after parsed. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: convert arm/hyp-abi.txt to ReSTMauro Carvalho Chehab2-9/+20
- Add proper markups for titles; - Adjust whitespaces and blank lines to match ReST needs; - Mark literal blocks as such. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: Convert api.txt to ReST formatMauro Carvalho Chehab2-1387/+1964
convert api.txt document to ReST format while trying to keep its format as close as possible with the authors intent, and avoid adding uneeded markups. - Use document title and chapter markups; - Convert tables; - Add markups for literal blocks; - use :field: for field descriptions; - Add blank lines and adjust indentation Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: convert devices/xive.txt to ReSTMauro Carvalho Chehab2-55/+98
- Use title markups; - adjust indentation and add blank lines as needed; - adjust tables to match ReST accepted formats; - mark code blocks as such. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: convert devices/xics.txt to ReSTMauro Carvalho Chehab2-6/+23
- Use title markups; - adjust indentation and add blank lines as needed; - adjust tables to match ReST accepted formats; - use :field: markups. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: convert devices/vm.txt to ReSTMauro Carvalho Chehab2-80/+127
- Use title markups; - adjust indentation and add blank lines as needed; - use :field: markups; - Use cross-references; - mark code blocks as such. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Reviewed-by: Cornelia Huck <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: convert devices/vfio.txt to ReSTMauro Carvalho Chehab2-10/+16
- Use standard title markup; - adjust lists; - mark code blocks as such. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Reviewed-by: Cornelia Huck <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: convert devices/vcpu.txt to ReSTMauro Carvalho Chehab3-76/+115
- Use title markups; - adjust indentation and add blank lines as needed; - adjust tables to match ReST accepted formats; - use :field: markups; - mark code blocks as such. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2020-02-12docs: kvm: convert devices/s390_flic.txt to ReSTMauro Carvalho Chehab2-30/+41
- Use standard markup for document title; - Adjust indentation and add blank lines as needed; - use the notes markup; - mark code blocks as such. Signed-off-by: Mauro Carvalho Chehab <[email protected]> Reviewed-by: Cornelia Huck <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.