| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[Why]
Potential out of bounds access in dml2_calculate_rq_and_dlg_params()
because the value of out_lowest_state_idx used as an index for FCLKChangeSupport
array can be greater than 1.
[How]
Currently dml2 core specifies identical values for all FCLKChangeSupport
elements. Always use index 0 in the condition to avoid out of bounds access.
Acked-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Jerry Zuo <[email protected]>
Signed-off-by: Roman Li <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Fix 4k240 underflow on dcn351
Acked-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Fangzhi Zuo <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Some of the panels does not have the refresh rate range info
in base EDID and only have the refresh rate range info in
DisplayID block.
It will cause the max/min freesync refresh rate set to 0.
[How]
Try to parse the refresh rate range info from DisplayID if the
max/min refresh rate is 0.
Reviewed-by: Sun peng Li <[email protected]>
Signed-off-by: Jerry Zuo <[email protected]>
Signed-off-by: Tom Chung <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Description]
We need to ensure to take into account cursor prefetch BW in
mode support or we may pass ModeQuery but fail an actual flip
which will cause a hang. Flip may fail because the cursor_pre_bw
is populated during mode programming (and mode programming is
never called prior to ModeQuery).
Reviewed-by: Chaitanya Dhere <[email protected]>
Reviewed-by: Nevenko Stupar <[email protected]>
Signed-off-by: Jerry Zuo <[email protected]>
Signed-off-by: Alvin Lee <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Commit 2f7b1d8b5505 ("clk: mediatek: Do a runtime PM get on controllers
during probe") enabled runtime PM for all mediatek clock controllers,
but this introduced an issue on the resume path.
If a device resumes earlier than the clock controller and calls
clk_prepare() when runtime PM is enabled on the controller, it will end
up calling clk_pm_runtime_get(). But the subsequent
pm_runtime_resume_and_get() call will fail because the runtime PM is
temporarily disabled during suspend.
To workaround this, introduce a need_runtime_pm flag and only enable it
on mt8183-mfgcfg, which is the driver that observed deadlock previously.
Hopefully mt8183-cfgcfg won't run into the issue at the resume stage
because the GPU should have stopped rendering before the system calls
suspend.
Fixes: 2f7b1d8b5505 ("clk: mediatek: Do a runtime PM get on controllers during probe")
Signed-off-by: Pin-yen Lin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Stephen Boyd <[email protected]>
|
|
[Why]
We only enable the VRR while monitor usable refresh rate range
is greater than 10 Hz.
But we did not check the range in DRM_EDID_FEATURE_CONTINUOUS_FREQ
case.
[How]
Add a refresh rate range check before set the freesync_capable flag
in DRM_EDID_FEATURE_CONTINUOUS_FREQ case.
Reviewed-by: Mario Limonciello <[email protected]>
Reviewed-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Jerry Zuo <[email protected]>
Signed-off-by: Tom Chung <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Sometimes the new_crtc_state->vrr_infopacket did not sync up with the
current state.
It will affect the update_freesync_state_on_stream() does not update
the state correctly.
[How]
Reset the freesync config before get_freesync_config_for_crtc() to
make sure we have the correct new_crtc_state for VRR.
Reviewed-by: Sun peng Li <[email protected]>
Signed-off-by: Jerry Zuo <[email protected]>
Signed-off-by: Tom Chung <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull one Allwinner SoC clk driver fix for 6.10
- Fix min/max rate clamping that caused a regression back in 6.9
* tag 'sunxi-clk-fixes-for-6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: common: Don't call hw_to_ccu_common on hw without common
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Dave Jiang:
- Fix no cxl_nvd during pmem region auto-assemble
- Avoid NULLL pointer dereference in region lookup
- Add missing checks to interleave capability
- Add cxl kdoc fix to address document compilation error
* tag 'cxl-fixes-6.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl: documentation: add missing files to cxl driver-api
cxl/region: check interleave capability
cxl/region: Avoid null pointer dereference in region lookup
cxl/mem: Fix no cxl_nvd during pmem region auto-assembling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"A fixup for a recent fix that prevents an infinite loop during block
group reclaim.
Unfortunately it introduced an unsafe way of updating block group list
and could race with relocation. This could be hit on fast devices when
relocation/balance does not have enough space"
* tag 'for-6.10-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix adding block group to a reclaim list and the unused list during reclaim
|
|
ON/OFF in the keys was swapped between the first and second argument of
the prctl. The prctl key is always PR_RISCV_SET_ICACHE_FLUSH_CTX, and
the second argument can be PR_RISCV_CTX_SW_FENCEI_ON or
PR_RISCV_CTX_SW_FENCEI_OFF.
Signed-off-by: Charlie Jenkins <[email protected]>
Fixes: 6a08e4709c58 ("documentation: Document PR_RISCV_SET_ICACHE_FLUSH_CTX prctl")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Palmer Dabbelt <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fix from Arnd Bergmann:
"This fixes up a last minute build regression from the previous set of
bug fixes"
* tag 'asm-generic-fixes-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
syscalls: fix sys_fanotify_mark prototype
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"A number of devicetree fixes came in for the rockchip platforms,
correcting some of the address information, and reverting a change to
the MMC controller configuration that caused regressions.
Four drivers have one code change each, addressing minor build issues
for the optee firmware driver, the litex SoC platform driver and two
reset drivers.
The riscv fixes as also simple, mainly turning off device nodes in the
canaan dts files unless they are actually usable on a particular
board.
Finally, Drew takes over maintaining the THEAD RISC-V SoC platform"
* tag 'arm-fixes-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
drivers/soc/litex: drop obsolete dependency on COMPILE_TEST
tee: optee: ffa: Fix missing-field-initializers warning
arm64: dts: rockchip: Add sound-dai-cells for RK3368
arm64: dts: rockchip: Fix the i2c address of es8316 on Cool Pi 4B
reset: hisilicon: hi6220: add missing MODULE_DESCRIPTION() macro
reset: gpio: Fix missing gpiolib dependency for GPIO reset controller
MAINTAINERS: thead: update Maintainer
arm64: dts: rockchip: fix PMIC interrupt pin on ROCK Pi E
riscv: dts: starfive: Set EMMC vqmmc maximum voltage to 3.3V on JH7110 boards
arm64: dts: rockchip: make poweroff(8) work on Radxa ROCK 5A
Revert "arm64: dts: rockchip: remove redundant cd-gpios from rk3588 sdmmc nodes"
ARM: dts: rockchip: rk3066a: add #sound-dai-cells to hdmi node
arm64: dts: rockchip: Fix the value of `dlg,jack-det-rate` mismatch on rk3399-gru
arm64: dts: rockchip: set correct pwm0 pinctrl on rk3588-tiger
riscv: dts: canaan: Disable I/O devices unless used
riscv: dts: canaan: Clean up serial aliases
arm64: dts: rockchip: Rename LED related pinctrl nodes on rk3308-rock-pi-s
arm64: dts: rockchip: Fix SD NAND and eMMC init on rk3308-rock-pi-s
arm64: dts: rockchip: Fix rk3308 codec@ff560000 reset-names
arm64: dts: rockchip: Fix the DCDC_REG2 minimum voltage on Quartz64 Model B
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
- Rockchip NAND controller driver was not checking the timings properly
and the introduction of NV-DDR support broke it.
- The core was also misbehaving in some very specific cases: in case of
(unlikely) bitflips in the parameter page, the fallback might have
failed as well but for software reasons.
- Finally, the chosen ECC configuration was no longer properly
propagated to upper layers, mostly failing an info message at probe
time.
* tag 'mtd/fixes-for-6.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: rockchip: ensure NVDDR timings are rejected
mtd: rawnand: Bypass a couple of sanity checks during NAND identification
mtd: rawnand: Fix the nand_read_data_op() early check
mtd: rawnand: Ensure ECC configuration is propagated to upper layers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
"Misc:
- Don't misleadingly warn during filesystem thaw operations.
It's possible that a block device which was frozen before it was
mounted can cause a failing thaw operation if someone concurrently
tried to mount it while that thaw operation was issued and the
device had already been temporarily claimed for the mount (The
mount will of course be aborted because the device is frozen).
netfs:
- Fix io_uring based write-through. Make sure that the total request
length is correctly set.
- Fix partial writes to folio tail.
- Remove some xarray helpers that were intended for bounce buffers
which got defered to a later patch series.
- Make netfs_page_mkwrite() whether folio->mapping is vallid after
acquiring the folio lock.
- Make netfs_page_mkrite() flush conflicting data instead of waiting.
fsnotify:
- Ensure that fsnotify creation events are generated before fsnotify
open events when a file is created via ->atomic_open(). The
ordering was broken before.
- Ensure that no fsnotify events are generated for O_PATH file
descriptors. While no fsnotify open events were generated, fsnotify
close events were. Make it consistent and don't produce any"
* tag 'vfs-6.10-rc7.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
netfs: Fix netfs_page_mkwrite() to flush conflicting data, not wait
netfs: Fix netfs_page_mkwrite() to check folio->mapping is valid
netfs: Delete some xarray-wangling functions that aren't used
netfs: Fix early issue of write op on partial write to folio tail
netfs: Fix io_uring based write-through
vfs: generate FS_CREATE before FS_OPEN when ->atomic_open used.
fsnotify: Do not generate events for O_PATH file descriptors
fs: don't misleadingly warn during thaw operations
|
|
When boost is set for CPUs using acpi-cpufreq, the policy is not
updated which can cause boost to be incorrectly not reported.
Fixes: 218a06a79d9a ("cpufreq: Support per-policy performance boost")
Link: https://patch.msgid.link/[email protected]
Suggested-by: Viresh Kumar <[email protected]>
Suggested-by: Gautham R. Shenoy <[email protected]>
Signed-off-by: Mario Limonciello <[email protected]>
Reviewed-by: Gautham R. Shenoy <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
Cc: All applicable <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
The behavior introduced in commit f37a4d6b4a2c ("cpufreq: Fix per-policy
boost behavior on SoCs using cpufreq_boost_set_sw()") sets up the boost
policy incorrectly when boost has been enabled by the platform firmware
initially even if a driver sets the policy up.
This is because policy_has_boost_freq() assumes that there is a frequency
table set up by the driver and that the boost frequencies are advertised
in that table. This assumption doesn't work for acpi-cpufreq or
amd-pstate. Only use this check to enable boost if it's not already
enabled instead of also disabling it if alreayd enabled.
Fixes: f37a4d6b4a2c ("cpufreq: Fix per-policy boost behavior on SoCs using cpufreq_boost_set_sw()")
Link: https://patch.msgid.link/[email protected]
Reviewed-by: Sibi Sankar <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
Reviewed-by: Gautham R. Shenoy <[email protected]>
Suggested-by: Viresh Kumar <[email protected]>
Suggested-by: Gautham R. Shenoy <[email protected]>
Signed-off-by: Mario Limonciello <[email protected]>
Cc: All applicable <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
reclaim
There is a potential parallel list adding for retrying in
btrfs_reclaim_bgs_work and adding to the unused list. Since the block
group is removed from the reclaim list and it is on a relocation work,
it can be added into the unused list in parallel. When that happens,
adding it to the reclaim list will corrupt the list head and trigger
list corruption like below.
Fix it by taking fs_info->unused_bgs_lock.
[177.504][T2585409] BTRFS error (device nullb1): error relocating ch= unk 2415919104
[177.514][T2585409] list_del corruption. next->prev should be ff1100= 0344b119c0, but was ff11000377e87c70. (next=3Dff110002390cd9c0)
[177.529][T2585409] ------------[ cut here ]------------
[177.537][T2585409] kernel BUG at lib/list_debug.c:65!
[177.545][T2585409] Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI
[177.555][T2585409] CPU: 9 PID: 2585409 Comm: kworker/u128:2 Tainted: G W 6.10.0-rc5-kts #1
[177.568][T2585409] Hardware name: Supermicro SYS-520P-WTR/X12SPW-TF, BIOS 1.2 02/14/2022
[177.579][T2585409] Workqueue: events_unbound btrfs_reclaim_bgs_work[btrfs]
[177.589][T2585409] RIP: 0010:__list_del_entry_valid_or_report.cold+0x70/0x72
[177.624][T2585409] RSP: 0018:ff11000377e87a70 EFLAGS: 00010286
[177.633][T2585409] RAX: 000000000000006d RBX: ff11000344b119c0 RCX:0000000000000000
[177.644][T2585409] RDX: 000000000000006d RSI: 0000000000000008 RDI:ffe21c006efd0f40
[177.655][T2585409] RBP: ff110002e0509f78 R08: 0000000000000001 R09:ffe21c006efd0f08
[177.665][T2585409] R10: ff11000377e87847 R11: 0000000000000000 R12:ff110002390cd9c0
[177.676][T2585409] R13: ff11000344b119c0 R14: ff110002e0508000 R15:dffffc0000000000
[177.687][T2585409] FS: 0000000000000000(0000) GS:ff11000fec880000(0000) knlGS:0000000000000000
[177.700][T2585409] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[177.709][T2585409] CR2: 00007f06bc7b1978 CR3: 0000001021e86005 CR4:0000000000771ef0
[177.720][T2585409] DR0: 0000000000000000 DR1: 0000000000000000 DR2:0000000000000000
[177.731][T2585409] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:0000000000000400
[177.742][T2585409] PKRU: 55555554
[177.748][T2585409] Call Trace:
[177.753][T2585409] <TASK>
[177.759][T2585409] ? __die_body.cold+0x19/0x27
[177.766][T2585409] ? die+0x2e/0x50
[177.772][T2585409] ? do_trap+0x1ea/0x2d0
[177.779][T2585409] ? __list_del_entry_valid_or_report.cold+0x70/0x72
[177.788][T2585409] ? do_error_trap+0xa3/0x160
[177.795][T2585409] ? __list_del_entry_valid_or_report.cold+0x70/0x72
[177.805][T2585409] ? handle_invalid_op+0x2c/0x40
[177.812][T2585409] ? __list_del_entry_valid_or_report.cold+0x70/0x72
[177.820][T2585409] ? exc_invalid_op+0x2d/0x40
[177.827][T2585409] ? asm_exc_invalid_op+0x1a/0x20
[177.834][T2585409] ? __list_del_entry_valid_or_report.cold+0x70/0x72
[177.843][T2585409] btrfs_delete_unused_bgs+0x3d9/0x14c0 [btrfs]
There is a similar retry_list code in btrfs_delete_unused_bgs(), but it is
safe, AFAICS. Since the block group was in the unused list, the used bytes
should be 0 when it was added to the unused list. Then, it checks
block_group->{used,reserved,pinned} are still 0 under the
block_group->lock. So, they should be still eligible for the unused list,
not the reclaim list.
The reason it is safe there it's because because we're holding
space_info->groups_sem in write mode.
That means no other task can allocate from the block group, so while we
are at deleted_unused_bgs() it's not possible for other tasks to
allocate and deallocate extents from the block group, so it can't be
added to the unused list or the reclaim list by anyone else.
The bug can be reproduced by btrfs/166 after a few rounds. In practice
this can be hit when relocation cannot find more chunk space and ends
with ENOSPC.
Reported-by: Shinichiro Kawasaki <[email protected]>
Suggested-by: Johannes Thumshirn <[email protected]>
Fixes: 4eb4e85c4f81 ("btrfs: retry block group reclaim without infinite loop")
CC: [email protected] # 5.15+
Reviewed-by: Filipe Manana <[email protected]>
Reviewed-by: Johannes Thumshirn <[email protected]>
Reviewed-by: Qu Wenruo <[email protected]>
Signed-off-by: Naohiro Aota <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
Check that all fields of a V2 algorithm header fit into the available
firmware data buffer.
The wmfw V2 format introduced variable-length strings in the algorithm
block header. This means the overall header length is variable, and the
position of most fields varies depending on the length of the string
fields. Each field must be checked to ensure that it does not overflow
the firmware data buffer.
As this ia bugfix patch, the fixes avoid making any significant change to
the existing code. This makes it easier to review and less likely to
introduce new bugs.
Signed-off-by: Richard Fitzgerald <[email protected]>
Fixes: f6bc909e7673 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Move the payload length check in cs_dsp_load() and cs_dsp_coeff_load()
to be done before the block is processed.
The check that the length of a block payload does not exceed the number
of remaining bytes in the firwmware file buffer was being done near the
end of the loop iteration. However, some code before that check used the
length field without validating it.
Signed-off-by: Richard Fitzgerald <[email protected]>
Fixes: f6bc909e7673 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Return an error from cs_dsp_power_up() if a block header is longer
than the amount of data left in the file.
The previous code in cs_dsp_load() and cs_dsp_load_coeff() would loop
while there was enough data left in the file for a valid region. This
protected against overrunning the end of the file data, but it didn't
abort the file processing with an error.
Signed-off-by: Richard Fitzgerald <[email protected]>
Fixes: f6bc909e7673 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Fix the checking that firmware file buffer is large enough for the
wmfw header, to prevent overrunning the buffer.
The original code tested that the firmware data buffer contained
enough bytes for the sums of the size of the structs
wmfw_header + wmfw_adsp1_sizes + wmfw_footer
But wmfw_adsp1_sizes is only used on ADSP1 firmware. For ADSP2 and
Halo Core the equivalent struct is wmfw_adsp2_sizes, which is
4 bytes longer. So the length check didn't guarantee that there
are enough bytes in the firmware buffer for a header with
wmfw_adsp2_sizes.
This patch splits the length check into three separate parts. Each
of the wmfw_header, wmfw_adsp?_sizes and wmfw_footer are checked
separately before they are used.
Signed-off-by: Richard Fitzgerald <[email protected]>
Fixes: f6bc909e7673 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
My earlier fix missed an incorrect function prototype that shows up on
native 32-bit builds:
In file included from fs/notify/fanotify/fanotify_user.c:14:
include/linux/syscalls.h:248:25: error: conflicting types for 'sys_fanotify_mark'; have 'long int(int, unsigned int, u32, u32, int, const char *)' {aka 'long int(int, unsigned int, unsigned int, unsigned int, int, const char *)'}
1924 | SYSCALL32_DEFINE6(fanotify_mark,
| ^~~~~~~~~~~~~~~~~
include/linux/syscalls.h:862:17: note: previous declaration of 'sys_fanotify_mark' with type 'long int(int, unsigned int, u64, int, const char *)' {aka 'long int(int, unsigned int, long long unsigned int, int, const char *)'}
On x86 and powerpc, the prototype is also wrong but hidden in an #ifdef,
so it never caused problems.
Add another alternative declaration that matches the conditional function
definition.
Fixes: 403f17a33073 ("parisc: use generic sys_fanotify_mark implementation")
Cc: [email protected]
Reported-by: Guenter Roeck <[email protected]>
Reported-by: Geert Uytterhoeven <[email protected]>
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Apart from the regular dts fixes for wrong addresses, missing
or wrong properties, this reverts the previous move away from
cd-gpios to the mmc-controller's internal card-detect.
With this change applied, it was reported that boards could not
detect card anymore, so this go reverted of course.
* tag 'v6.10-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add sound-dai-cells for RK3368
arm64: dts: rockchip: Fix the i2c address of es8316 on Cool Pi 4B
arm64: dts: rockchip: fix PMIC interrupt pin on ROCK Pi E
arm64: dts: rockchip: make poweroff(8) work on Radxa ROCK 5A
Revert "arm64: dts: rockchip: remove redundant cd-gpios from rk3588 sdmmc nodes"
ARM: dts: rockchip: rk3066a: add #sound-dai-cells to hdmi node
arm64: dts: rockchip: Fix the value of `dlg,jack-det-rate` mismatch on rk3399-gru
arm64: dts: rockchip: set correct pwm0 pinctrl on rk3588-tiger
arm64: dts: rockchip: Rename LED related pinctrl nodes on rk3308-rock-pi-s
arm64: dts: rockchip: Fix SD NAND and eMMC init on rk3308-rock-pi-s
arm64: dts: rockchip: Fix rk3308 codec@ff560000 reset-names
arm64: dts: rockchip: Fix the DCDC_REG2 minimum voltage on Quartz64 Model B
Link: https://lore.kernel.org/r/10237789.nnTZe4vzsl@diego
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
in rare cases, e.g. for injecting a machine check we do intercept all
load PSW instructions via ICTL_LPSW. With facility 193 a new variant
LPSWEY was added. KVM needs to handle that as well.
Fixes: a3efa8429266 ("KVM: s390: gen_facilities: allow facilities 165, 193, 194 and 196")
Reported-by: Marc Hartmayer <[email protected]>
Reviewed-by: Sven Schnelle <[email protected]>
Reviewed-by: Claudio Imbrenda <[email protected]>
Signed-off-by: Christian Borntraeger <[email protected]>
Message-ID: <[email protected]>
|
|
On the OMAPL138, the SPI reference clock is provided by the Power and
Sleep Controller (PSC). The PSC's datasheet says that 'some peripherals
have special programming requirements and additional recommended steps
you must take before you can invoke the PSC module state transition'. I
didn't find more details in documentation but it appears that PSC needs
the SPI to clear the POWERDOWN bit before disabling the clock. Indeed,
when this bit is set, the PSC gets stuck in transitions from enable to
disable state.
Clear the POWERDOWN bit when releasing driver's resources
Signed-off-by: Bastien Curutchet <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth into main
bluetooth pull request for net:
- Ignore too large handle values in BIG
- L2CAP: sync sock recv cb and release
- hci_bcm4377: Fix msgid release
- ISO: Check socket flag instead of hcon
- hci_event: Fix setting of unicast qos interval
- hci: disallow setting handle bigger than HCI_CONN_HANDLE_MAX
- Add quirk to ignore reserved PHY bits in LE Extended Adv Report
- hci_core: cancel all works upon hci_unregister_dev
- btintel_pcie: Fix REVERSE_INULL issue reported by coverity
- qca: Fix BT enable failure again for QCA6390 after warm reboot
Signed-off-by: David S. Miller <[email protected]>
|
|
This accounts for the existence of two Steam Deck revisions
instead of a single revision
Signed-off-by: Matthew Schwartz <[email protected]>
Reviewed-by: Mario Limonciello <[email protected]>
Signed-off-by: Hamza Mahfooz <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Valve's Steam Deck Galileo revision has a 800x1280 OLED panel
Cc: [email protected] # 6.1+
Signed-off-by: John Schoenick <[email protected]>
Signed-off-by: Matthew Schwartz <[email protected]>
Signed-off-by: Hamza Mahfooz <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
It was reported that in moving to 6.1, a larger then 10%
regression was seen in the performance of
clock_gettime(CLOCK_THREAD_CPUTIME_ID,...).
Using a simple reproducer, I found:
5.10:
100000000 calls in 24345994193 ns => 243.460 ns per call
100000000 calls in 24288172050 ns => 242.882 ns per call
100000000 calls in 24289135225 ns => 242.891 ns per call
6.1:
100000000 calls in 28248646742 ns => 282.486 ns per call
100000000 calls in 28227055067 ns => 282.271 ns per call
100000000 calls in 28177471287 ns => 281.775 ns per call
The cause of this was finally narrowed down to the addition of
psi_account_irqtime() in update_rq_clock_task(), in commit
52b1364ba0b1 ("sched/psi: Add PSI_IRQ to track IRQ/SOFTIRQ
pressure").
In my initial attempt to resolve this, I leaned towards moving
all accounting work out of the clock_gettime() call path, but it
wasn't very pretty, so it will have to wait for a later deeper
rework. Instead, Peter shared this approach:
Rework psi_account_irqtime() to use its own psi_irq_time base
for accounting, and move it out of the hotpath, calling it
instead from sched_tick() and __schedule().
In testing this, we found the importance of ensuring
psi_account_irqtime() is run under the rq_lock, which Johannes
Weiner helpfully explained, so also add some lockdep annotations
to make that requirement clear.
With this change the performance is back in-line with 5.10:
6.1+fix:
100000000 calls in 24297324597 ns => 242.973 ns per call
100000000 calls in 24318869234 ns => 243.189 ns per call
100000000 calls in 24291564588 ns => 242.916 ns per call
Reported-by: Jimmy Shiu <[email protected]>
Originally-by: Peter Zijlstra <[email protected]>
Signed-off-by: John Stultz <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Reviewed-by: Chengming Zhou <[email protected]>
Reviewed-by: Qais Yousef <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
During the execution of the following stress test with linux-rt:
stress-ng --cyclic 30 --timeout 30 --minimize --quiet
kmemleak frequently reported a memory leak concerning the task_struct:
unreferenced object 0xffff8881305b8000 (size 16136):
comm "stress-ng", pid 614, jiffies 4294883961 (age 286.412s)
object hex dump (first 32 bytes):
02 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 .@..............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
debug hex dump (first 16 bytes):
53 09 00 00 00 00 00 00 00 00 00 00 00 00 00 00 S...............
backtrace:
[<00000000046b6790>] dup_task_struct+0x30/0x540
[<00000000c5ca0f0b>] copy_process+0x3d9/0x50e0
[<00000000ced59777>] kernel_clone+0xb0/0x770
[<00000000a50befdc>] __do_sys_clone+0xb6/0xf0
[<000000001dbf2008>] do_syscall_64+0x5d/0xf0
[<00000000552900ff>] entry_SYSCALL_64_after_hwframe+0x6e/0x76
The issue occurs in start_dl_timer(), which increments the task_struct
reference count and sets a timer. The timer callback, dl_task_timer,
is supposed to decrement the reference count upon expiration. However,
if enqueue_task_dl() is called before the timer expires and cancels it,
the reference count is not decremented, leading to the leak.
This patch fixes the reference leak by ensuring the task_struct
reference count is properly decremented when the timer is canceled.
Fixes: feff2e65efd8 ("sched/deadline: Unthrottle PI boosted threads while enqueuing")
Signed-off-by: Wander Lairson Costa <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Acked-by: Juri Lelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This reverts commit b0defa7ae03ecf91b8bfd10ede430cff12fcbd06.
b0defa7ae03ec changed the load balancing logic to ignore env.max_loop if
all tasks examined to that point were pinned. The goal of the patch was
to make it more likely to be able to detach a task buried in a long list
of pinned tasks. However, this has the unfortunate side effect of
creating an O(n) iteration in detach_tasks(), as we now must fully
iterate every task on a cpu if all or most are pinned. Since this load
balance code is done with rq lock held, and often in softirq context, it
is very easy to trigger hard lockups. We observed such hard lockups with
a user who affined O(10k) threads to a single cpu.
When I discussed this with Vincent he initially suggested that we keep
the limit on the number of tasks to detach, but increase the number of
tasks we can search. However, after some back and forth on the mailing
list, he recommended we instead revert the original patch, as it seems
likely no one was actually getting hit by the original issue.
Fixes: b0defa7ae03e ("sched/fair: Make sure to try to detach at least one movable task")
Signed-off-by: Josh Don <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Reviewed-by: Vincent Guittot <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
I don't see anything checking that TCP_METRICS_ATTR_SADDR_IPV4
is at least 4 bytes long, and the policy doesn't have an entry
for this attribute at all (neither does it for IPv6 but v6 is
manually validated).
Reviewed-by: Eric Dumazet <[email protected]>
Fixes: 3e7013ddf55a ("tcp: metrics: Allow selective get/del of tcp-metrics based on src IP")
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
For MTL+ platforms we use PICA chips for Type-C support and
hence mg programming is not needed.
Fixes issue with drm warn of TC port not being in legacy mode.
Cc: [email protected]
Signed-off-by: Mika Kahola <[email protected]>
Signed-off-by: Imre Deak <[email protected]>
Reviewed-by: Gustavo Sousa <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit aaf9dc86bd806458f848c39057d59e5aa652a399)
Signed-off-by: Jani Nikula <[email protected]>
|
|
Explicitly set the 'family' driver_info struct member for leafimx.
Previously, the correct operation relied on KVASER_LEAF being the first
defined value in enum kvaser_usb_leaf_family.
Fixes: e6c80e601053 ("can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression")
Signed-off-by: Jimmy Assarsson <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Cc: [email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fixes from Niklas Cassel:
- Add NOLPM quirk for for all Crucial BX SSD1 models.
Considering that we now have had bug reports for 3 different BX SSD1
variants from Crucial with the same product name, make the quirk more
inclusive, to catch more device models from the same generation.
- Fix a trivial NULL pointer dereference in the error path for
ata_host_release().
- Create a ata_port_free(), so that we don't miss freeing ata_port
struct members when freeing a struct ata_port.
- Fix a trivial double free in the error path for ata_host_alloc().
- Ensure that we remove the libata "remapped NVMe device count" sysfs
entry on .probe() error.
* tag 'ata-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: ahci: Clean up sysfs file on error
ata: libata-core: Fix double free on error
ata,scsi: libata-core: Do not leak memory for ata_port struct members
ata: libata-core: Fix null pointer dereference on error
ata: libata-core: Add ATA_HORKAGE_NOLPM for all Crucial BX SSD1 models
|
|
.probe() (ahci_init_one()) calls sysfs_add_file_to_group(), however,
if probe() fails after this call, we currently never call
sysfs_remove_file_from_group().
(The sysfs_remove_file_from_group() call in .remove() (ahci_remove_one())
does not help, as .remove() is not called on .probe() error.)
Thus, if probe() fails after the sysfs_add_file_to_group() call, the next
time we insmod the module we will get:
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:04.0/remapped_nvme'
CPU: 11 PID: 954 Comm: modprobe Not tainted 6.10.0-rc5 #43
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
sysfs_warn_dup.cold+0x17/0x23
sysfs_add_file_mode_ns+0x11a/0x130
sysfs_add_file_to_group+0x7e/0xc0
ahci_init_one+0x31f/0xd40 [ahci]
Fixes: 894fba7f434a ("ata: ahci: Add sysfs attribute to show remapped NVMe device count")
Cc: [email protected]
Reviewed-by: Damien Le Moal <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Niklas Cassel <[email protected]>
|
|
If e.g. the ata_port_alloc() call in ata_host_alloc() fails, we will jump
to the err_out label, which will call devres_release_group().
devres_release_group() will trigger a call to ata_host_release().
ata_host_release() calls kfree(host), so executing the kfree(host) in
ata_host_alloc() will lead to a double free:
kernel BUG at mm/slub.c:553!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 11 PID: 599 Comm: (udev-worker) Not tainted 6.10.0-rc5 #47
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014
RIP: 0010:kfree+0x2cf/0x2f0
Code: 5d 41 5e 41 5f 5d e9 80 d6 ff ff 4d 89 f1 41 b8 01 00 00 00 48 89 d9 48 89 da
RSP: 0018:ffffc90000f377f0 EFLAGS: 00010246
RAX: ffff888112b1f2c0 RBX: ffff888112b1f2c0 RCX: ffff888112b1f320
RDX: 000000000000400b RSI: ffffffffc02c9de5 RDI: ffff888112b1f2c0
RBP: ffffc90000f37830 R08: 0000000000000000 R09: 0000000000000000
R10: ffffc90000f37610 R11: 617461203a736b6e R12: ffffea00044ac780
R13: ffff888100046400 R14: ffffffffc02c9de5 R15: 0000000000000006
FS: 00007f2f1cabe980(0000) GS:ffff88813b380000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2f1c3acf75 CR3: 0000000111724000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
<TASK>
? __die_body.cold+0x19/0x27
? die+0x2e/0x50
? do_trap+0xca/0x110
? do_error_trap+0x6a/0x90
? kfree+0x2cf/0x2f0
? exc_invalid_op+0x50/0x70
? kfree+0x2cf/0x2f0
? asm_exc_invalid_op+0x1a/0x20
? ata_host_alloc+0xf5/0x120 [libata]
? ata_host_alloc+0xf5/0x120 [libata]
? kfree+0x2cf/0x2f0
ata_host_alloc+0xf5/0x120 [libata]
ata_host_alloc_pinfo+0x14/0xa0 [libata]
ahci_init_one+0x6c9/0xd20 [ahci]
Ensure that we will not call kfree(host) twice, by performing the kfree()
only if the devres_open_group() call failed.
Fixes: dafd6c496381 ("libata: ensure host is free'd on error exit paths")
Cc: [email protected]
Reviewed-by: Damien Le Moal <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Niklas Cassel <[email protected]>
|
|
libsas is currently not freeing all the struct ata_port struct members,
e.g. ncq_sense_buf for a driver supporting Command Duration Limits (CDL).
Add a function, ata_port_free(), that is used to free a ata_port,
including its struct members. It makes sense to keep the code related to
freeing a ata_port in its own function, which will also free all the
struct members of struct ata_port.
Fixes: 18bd7718b5c4 ("scsi: ata: libata: Handle completion of CDL commands using policy 0xD")
Reviewed-by: John Garry <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Niklas Cassel <[email protected]>
|
|
If the ata_port_alloc() call in ata_host_alloc() fails,
ata_host_release() will get called.
However, the code in ata_host_release() tries to free ata_port struct
members unconditionally, which can lead to the following:
BUG: unable to handle page fault for address: 0000000000003990
PGD 0 P4D 0
Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 10 PID: 594 Comm: (udev-worker) Not tainted 6.10.0-rc5 #44
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014
RIP: 0010:ata_host_release.cold+0x2f/0x6e [libata]
Code: e4 4d 63 f4 44 89 e2 48 c7 c6 90 ad 32 c0 48 c7 c7 d0 70 33 c0 49 83 c6 0e 41
RSP: 0018:ffffc90000ebb968 EFLAGS: 00010246
RAX: 0000000000000041 RBX: ffff88810fb52e78 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff88813b3218c0 RDI: ffff88813b3218c0
RBP: ffff88810fb52e40 R08: 0000000000000000 R09: 6c65725f74736f68
R10: ffffc90000ebb738 R11: 73692033203a746e R12: 0000000000000004
R13: 0000000000000000 R14: 0000000000000011 R15: 0000000000000006
FS: 00007f6cc55b9980(0000) GS:ffff88813b300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000003990 CR3: 00000001122a2000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
<TASK>
? __die_body.cold+0x19/0x27
? page_fault_oops+0x15a/0x2f0
? exc_page_fault+0x7e/0x180
? asm_exc_page_fault+0x26/0x30
? ata_host_release.cold+0x2f/0x6e [libata]
? ata_host_release.cold+0x2f/0x6e [libata]
release_nodes+0x35/0xb0
devres_release_group+0x113/0x140
ata_host_alloc+0xed/0x120 [libata]
ata_host_alloc_pinfo+0x14/0xa0 [libata]
ahci_init_one+0x6c9/0xd20 [ahci]
Do not access ata_port struct members unconditionally.
Fixes: 633273a3ed1c ("libata-pmp: hook PMP support and enable it")
Cc: [email protected]
Reviewed-by: Damien Le Moal <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: John Garry <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Niklas Cassel <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Remove the executable bit from installed DTB files
- Escape $ in subshell execution in the debian-orig target
- Fix RPM builds with CONFIG_MODULES=n
- Fix xconfig with the O= option
- Fix scripts_gdb with the O= option
* tag 'kbuild-fixes-v6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: scripts/gdb: bring the "abspath" back
kbuild: Use $(obj)/%.cc to fix host C++ module builds
kbuild: rpm-pkg: fix build error with CONFIG_MODULES=n
kbuild: Fix build target deb-pkg: ln: failed to create hard link
kbuild: doc: Update default INSTALL_MOD_DIR from extra to updates
kbuild: Install dtb files as 0644 in Makefile.dtbinst
|
|
The kernel test robot reported that clang no longer compiles the 32-bit
x86 kernel in some configurations due to commit 95ece48165c1
("locking/atomic/x86: Rewrite x86_32 arch_atomic64_{,fetch}_{and,or,xor}()
functions").
The build fails with
arch/x86/include/asm/cmpxchg_32.h:149:9: error: inline assembly requires more registers than available
and the reason seems to be that not only does the cmpxchg8b instruction
need four fixed registers (EDX:EAX and ECX:EBX), with the emulation
fallback the inline asm also wants a fifth fixed register for the
address (it uses %esi for that, but that's just a software convention
with cmpxchg8b_emu).
Avoiding using another pointer input to the asm (and just forcing it to
use the "0(%esi)" addressing that we end up requiring for the sw
fallback) seems to fix the issue.
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Fixes: 95ece48165c1 ("locking/atomic/x86: Rewrite x86_32 arch_atomic64_{,fetch}_{and,or,xor}() functions")
Link: https://lore.kernel.org/all/[email protected]/
Suggested-by: Uros Bizjak <[email protected]>
Reviewed-and-Tested-by: Uros Bizjak <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small driver fixes for 6.10-rc6. Included in here are:
- IIO driver fixes for reported issues
- Counter driver fix for a reported problem.
All of these have been in linux-next this week with no reported
issues"
* tag 'char-misc-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
counter: ti-eqep: enable clock at probe
iio: chemical: bme680: Fix sensor data read operation
iio: chemical: bme680: Fix overflows in compensate() functions
iio: chemical: bme680: Fix calibration data variable
iio: chemical: bme680: Fix pressure value output
iio: humidity: hdc3020: fix hysteresis representation
iio: dac: fix ad9739a random config compile error
iio: accel: fxls8962af: select IIO_BUFFER & IIO_KFIFO_BUF
iio: adc: ad7266: Fix variable checking bug
iio: xilinx-ams: Don't include ams_ctrl_channels in scan_mask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are two small staging driver fixes for 6.10-rc6, both for the
vc04_services drivers:
- build fix if CONFIG_DEBUGFS was not set
- initialization check fix that was much reported.
Both of these have been in linux-next this week with no reported
issues"
* tag 'staging-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vchiq_debugfs: Fix build if CONFIG_DEBUG_FS is not set
staging: vc04_services: vchiq_arm: Fix initialisation check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial / console fixes from Greg KH:
"Here are a bunch of fixes/reverts for 6.10-rc6. Include in here are:
- revert the bunch of tty/serial/console changes that landed in -rc1
that didn't quite work properly yet.
Everyone agreed to just revert them for now and will work on making
them better for a future release instead of trying to quick fix the
existing changes this late in the release cycle
- 8250 driver port count bugfix
- Other tiny serial port bugfixes for reported issues
All of these have been in linux-next this week with no reported
issues"
* tag 'tty-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "printk: Save console options for add_preferred_console_match()"
Revert "printk: Don't try to parse DEVNAME:0.0 console options"
Revert "printk: Flag register_console() if console is set on command line"
Revert "serial: core: Add support for DEVNAME:0.0 style naming for kernel console"
Revert "serial: core: Handle serial console options"
Revert "serial: 8250: Add preferred console in serial8250_isa_init_ports()"
Revert "Documentation: kernel-parameters: Add DEVNAME:0.0 format for serial ports"
Revert "serial: 8250: Fix add preferred console for serial8250_isa_init_ports()"
Revert "serial: core: Fix ifdef for serial base console functions"
serial: bcm63xx-uart: fix tx after conversion to uart_port_tx_limited()
serial: core: introduce uart_port_tx_limited_flags()
Revert "serial: core: only stop transmit when HW fifo is empty"
serial: imx: set receiver level before starting uart
tty: mcf: MCF54418 has 10 UARTS
serial: 8250_omap: Implementation of Errata i2310
tty: serial: 8250: Fix port count mismatch with the device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a handful of small USB driver fixes for 6.10-rc6 to resolve
some reported issues. Included in here are:
- typec driver bugfixes
- usb gadget driver reverts for commits that were reported to have
problems
- resource leak bugfix
- gadget driver bugfixes
- dwc3 driver bugfixes
- usb atm driver bugfix for when syzbot got loose on it
All of these have been in linux-next this week with no reported issues"
* tag 'usb-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: dwc3: core: Workaround for CSR read timeout
Revert "usb: gadget: u_ether: Replace netif_stop_queue with netif_device_detach"
Revert "usb: gadget: u_ether: Re-attach netif device to mirror detachment"
usb: gadget: aspeed_udc: fix device address configuration
usb: dwc3: core: remove lock of otg mode during gadget suspend/resume to avoid deadlock
usb: typec: ucsi: glink: fix child node release in probe function
usb: musb: da8xx: fix a resource leak in probe()
usb: typec: ucsi_acpi: Add LG Gram quirk
usb: ucsi: stm32: fix command completion handling
usb: atm: cxacru: fix endpoint checking in cxacru_bind()
usb: gadget: printer: fix races against disable
usb: gadget: printer: SS+ support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp fixes from Borislav Petkov:
- Fix "nosmp" and "maxcpus=0" after the parallel CPU bringup work went
in and broke them
- Make sure CPU hotplug dynamic prepare states are actually executed
* tag 'smp_urgent_for_v6.10_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu: Fix broken cmdline "nosmp" and "maxcpus=0"
cpu/hotplug: Fix dynstate assignment in __cpuhp_setup_state_cpuslocked()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Make sure multi-bridge machines get all eiointc interrupt controllers
initialized even if the number of CPUs has been limited by a cmdline
param
- Make sure interrupt lines on liointc hw are configured properly even
when interrupt routing changes
- Avoid use-after-free in the error path of the MSI init code
* tag 'irq_urgent_for_v6.10_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI/MSI: Fix UAF in msi_capability_init
irqchip/loongson-liointc: Set different ISRs for different cores
irqchip/loongson-eiointc: Use early_cpu_to_node() instead of cpu_to_node()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Borislav Petkov:
- Warn when an hrtimer doesn't get a callback supplied
* tag 'timers_urgent_for_v6.10_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Prevent queuing of hrtimer without a function callback
|