| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since the rework of the vector management, warnings about spurious
interrupts have been reported. Robert provided some more information and
did an initial analysis. The following situation leads to these warnings:
CPU 0 CPU 1 IO_APIC
interrupt is raised
sent to CPU1
Unable to handle
immediately
(interrupts off,
deep idle delay)
mask()
...
free()
shutdown()
synchronize_irq()
clear_vector()
do_IRQ()
-> vector is clear
Before the rework the vector entries of legacy interrupts were statically
assigned and occupied precious vector space while most of them were
unused. Due to that the above situation was handled silently because the
vector was handled and the core handler of the assigned interrupt
descriptor noticed that it is shut down and returned.
While this has been usually observed with legacy interrupts, this situation
is not limited to them. Any other interrupt source, e.g. MSI, can cause the
same issue.
After adding proper synchronization for level triggered interrupts, this
can only happen for edge triggered interrupts where the IO-APIC obviously
cannot provide information about interrupts in flight.
While the spurious warning is actually harmless in this case it worries
users and driver developers.
Handle it gracefully by marking the vector entry as VECTOR_SHUTDOWN instead
of VECTOR_UNUSED when the vector is freed up.
If that above late handling happens the spurious detector will not complain
and switch the entry to VECTOR_UNUSED. Any subsequent spurious interrupt on
that line will trigger the spurious warning as before.
Fixes: 464d12309e1b ("x86/vector: Switch IOAPIC to global reservation mode")
Reported-by: Robert Hodaszi <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>-
Tested-by: Robert Hodaszi <[email protected]>
Cc: Marc Zyngier <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
When an interrupt is shut down in free_irq() there might be an inflight
interrupt pending in the IO-APIC remote IRR which is not yet serviced. That
means the interrupt has been sent to the target CPUs local APIC, but the
target CPU is in a state which delays the servicing.
So free_irq() would proceed to free resources and to clear the vector
because synchronize_hardirq() does not see an interrupt handler in
progress.
That can trigger a spurious interrupt warning, which is harmless and just
confuses users, but it also can leave the remote IRR in a stale state
because once the handler is invoked the interrupt resources might be freed
already and therefore acknowledgement is not possible anymore.
Implement the irq_get_irqchip_state() callback for the IO-APIC irq chip. The
callback is invoked from free_irq() via __synchronize_hardirq(). Check the
remote IRR bit of the interrupt and return 'in flight' if it is set and the
interrupt is configured in level mode. For edge mode the remote IRR has no
meaning.
As this is only meaningful for level triggered interrupts this won't cure
the potential spurious interrupt warning for edge triggered interrupts, but
the edge trigger case does not result in stale hardware state. This has to
be addressed at the vector/interrupt entry level seperately.
Fixes: 464d12309e1b ("x86/vector: Switch IOAPIC to global reservation mode")
Reported-by: Robert Hodaszi <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Marc Zyngier <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
free_irq() ensures that no hardware interrupt handler is executing on a
different CPU before actually releasing resources and deactivating the
interrupt completely in a domain hierarchy.
But that does not catch the case where the interrupt is on flight at the
hardware level but not yet serviced by the target CPU. That creates an
interesing race condition:
CPU 0 CPU 1 IRQ CHIP
interrupt is raised
sent to CPU1
Unable to handle
immediately
(interrupts off,
deep idle delay)
mask()
...
free()
shutdown()
synchronize_irq()
release_resources()
do_IRQ()
-> resources are not available
That might be harmless and just trigger a spurious interrupt warning, but
some interrupt chips might get into a wedged state.
Utilize the existing irq_get_irqchip_state() callback for the
synchronization in free_irq().
synchronize_hardirq() is not using this mechanism as it might actually
deadlock unter certain conditions, e.g. when called with interrupts
disabled and the target CPU is the one on which the synchronization is
invoked. synchronize_irq() uses it because that function cannot be called
from non preemtible contexts as it might sleep.
No functional change intended and according to Marc the existing GIC
implementations where the driver supports the callback should be able
to cope with that core change. Famous last words.
Fixes: 464d12309e1b ("x86/vector: Switch IOAPIC to global reservation mode")
Reported-by: Robert Hodaszi <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Marc Zyngier <[email protected]>
Tested-by: Marc Zyngier <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
The function might sleep, so it cannot be called from interrupt
context. Not even with care.
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Marc Zyngier <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
When interrupts are shutdown, they are immediately deactivated in the
irqdomain hierarchy. While this looks obviously correct there is a subtle
issue:
There might be an interrupt in flight when free_irq() is invoking the
shutdown. This is properly handled at the irq descriptor / primary handler
level, but the deactivation might completely disable resources which are
required to acknowledge the interrupt.
Split the shutdown code and deactivate the interrupt after synchronization
in free_irq(). Fixup all other usage sites where this is not an issue to
invoke the combined shutdown_and_deactivate() function instead.
This still might be an issue if the interrupt in flight servicing is
delayed on a remote CPU beyond the invocation of synchronize_irq(), but
that cannot be handled at that level and needs to be handled in the
synchronize_irq() context.
Fixes: f8264e34965a ("irqdomain: Introduce new interfaces to support hierarchy irqdomains")
Reported-by: Robert Hodaszi <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Marc Zyngier <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
Fix minimum encryption key size check so that HCI_MIN_ENC_KEY_SIZE is
also allowed as stated in the comment.
This bug caused connection problems with devices having maximum
encryption key size of 7 octets (56-bit).
Fixes: 693cd8ce3f88 ("Bluetooth: Fix regression with minimum encryption key size alignment")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203997
Signed-off-by: Matias Karhumaa <[email protected]>
Cc: [email protected]
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Pull cifs fix from Steve French:
"SMB3 fix (for stable as well) for crash mishandling one of the Windows
reparse point symlink tags"
* tag '5.2-rc6-smb3-fix' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix crash querying symlinks stored as reparse-points
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd fork() fix from Christian Brauner:
"A single small fix for copy_process() in kernel/fork.c:
With Al's removal of ksys_close() from cleanup paths in copy_process()
a bug was introduced. When anon_inode_getfile() failed the cleanup was
correctly performed but the error code was not propagated to callers
of copy_process() causing them to operate on a nonsensical pointer.
The fix is a simple on-liner which makes sure that a proper negative
error code is returned from copy_process().
syzkaller has also verified that the bug is not reproducible with this
fix"
* tag 'for-linus-20190701' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
fork: return proper negative error code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Fix a build failure with the LLVM linker and a module allocation
failure when KASLR is active:
- Fix module allocation when running with KASLR enabled
- Fix broken build due to bug in LLVM linker (ld.lld)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/efi: Mark __efistub_stext_offset as an absolute symbol explicitly
arm64: kaslr: keep modules inside module region when KASAN is enabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
This set of patches fixes regressions introduced in v5.2 kernel when DA8xx
OHCI driver was converted over to use GPIO regulators.
* tag 'davinci-fixes-for-v5.2-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da830-evm: fix GPIO lookup for OHCI
ARM: davinci: omapl138-hawk: add missing regulator constraints for OHCI
ARM: davinci: da830-evm: add missing regulator constraints for OHCI
+ Linux 5.2-rc7
Signed-off-by: Olof Johansson <[email protected]>
|
|
If the CHAP_A value is not supported, the chap_server_open() function
should free the auth_protocol pointer and set it to NULL, or we will leave
a dangling pointer around.
[ 66.010905] Unsupported CHAP_A value
[ 66.011660] Security negotiation failed.
[ 66.012443] iSCSI Login negotiation failed.
[ 68.413924] general protection fault: 0000 [#1] SMP PTI
[ 68.414962] CPU: 0 PID: 1562 Comm: targetcli Kdump: loaded Not tainted 4.18.0-80.el8.x86_64 #1
[ 68.416589] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 68.417677] RIP: 0010:__kmalloc_track_caller+0xc2/0x210
Signed-off-by: Maurizio Lombardi <[email protected]>
Reviewed-by: Chris Leech <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
WRITE SAME corrupts data on the block device behind iblock if the command
is emulated. The emulation code issues (M - 1) * N times more bios than
requested, where M is the number of 512 blocks per real block size and N is
the NUMBER OF LOGICAL BLOCKS specified in WRITE SAME command. So, for a
device with 4k blocks, 7 * N more LBAs gets written after the requested
range.
The issue happens because the number of 512 byte sectors to be written is
decreased one by one while the real bios are typically from 1 to 8 512 byte
sectors per bio.
Fixes: c66ac9db8d4a ("[SCSI] target: Add LIO target core v4.0.0-rc6")
Cc: <[email protected]>
Signed-off-by: Roman Bolshakov <[email protected]>
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
I ran into an intriguing bug caused by
commit ""spi: gpio: Don't request CS GPIO in DT use-case"
affecting all SPI GPIO devices with an active high
chip select line.
The commit switches the CS gpio handling over to the GPIO
core, which will parse and handle "cs-gpios" from the OF
node without even calling down to the driver to get the
job done.
However the GPIO core handles the standard bindings in
Documentation/devicetree/bindings/spi/spi-controller.yaml
that specifies that active high CS needs to be specified
using "spi-cs-high" in the DT node.
The code in drivers/spi/spi-gpio.c never respected this
and never tried to inspect subnodes to see if they contained
"spi-cs-high" like the gpiolib OF quirks does. Instead the
only way to get an active high CS was to tag it in the
device tree using the flags cell such as
cs-gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
This alters the quirks to not inspect the subnodes of SPI
masters on "spi-gpio" for the standard attribute "spi-cs-high",
making old device trees work as expected.
This semantic is a bit ambigous, but just allowing the
flags on the GPIO descriptor to modify polarity is what
the kernel at large mostly uses so let's encourage that.
Fixes: 249e2632dcd0 ("spi: gpio: Don't request CS GPIO in DT use-case")
Cc: Andrey Smirnov <[email protected]>
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Linus Walleij <[email protected]>
|
|
ftrace_arch_code_modify_post_process() and ftrace_arch_code_modify_prepare()
ftrace_arch_code_modify_prepare() is acquiring text_mutex, while the
corresponding release is happening in ftrace_arch_code_modify_post_process().
This has already been documented in the code, but let's also make the fact
that this is intentional clear to the semantic analysis tools such as sparse.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 39611265edc1a ("ftrace/x86: Add a comment to why we take text_mutex in ftrace_arch_code_modify_prepare()")
Fixes: d5b844a2cf507 ("ftrace/x86: Remove possible deadlock between register_kprobe() and ftrace_run_update_code()")
Signed-off-by: Jiri Kosina <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
LINE6 drivers allocate the buffers based on the value returned from
usb_maxpacket() calls. The manipulated device may return zero for
this, and this results in the kmalloc() with zero size (and it may
succeed) while the other part of the driver code writes the packet
data with the fixed size -- which eventually overwrites.
This patch adds a simple sanity check for the invalid buffer size for
avoiding that problem.
Reported-by: [email protected]
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Thomas reported that:
| Background:
|
| In preparation of supporting IPI shorthands I changed the CPU offline
| code to software disable the local APIC instead of just masking it.
| That's done by clearing the APIC_SPIV_APIC_ENABLED bit in the APIC_SPIV
| register.
|
| Failure:
|
| When the CPU comes back online the startup code triggers occasionally
| the warning in apic_pending_intr_clear(). That complains that the IRRs
| are not empty.
|
| The offending vector is the local APIC timer vector who's IRR bit is set
| and stays set.
|
| It took me quite some time to reproduce the issue locally, but now I can
| see what happens.
|
| It requires apicv_enabled=0, i.e. full apic emulation. With apicv_enabled=1
| (and hardware support) it behaves correctly.
|
| Here is the series of events:
|
| Guest CPU
|
| goes down
|
| native_cpu_disable()
|
| apic_soft_disable();
|
| play_dead()
|
| ....
|
| startup()
|
| if (apic_enabled())
| apic_pending_intr_clear() <- Not taken
|
| enable APIC
|
| apic_pending_intr_clear() <- Triggers warning because IRR is stale
|
| When this happens then the deadline timer or the regular APIC timer -
| happens with both, has fired shortly before the APIC is disabled, but the
| interrupt was not serviced because the guest CPU was in an interrupt
| disabled region at that point.
|
| The state of the timer vector ISR/IRR bits:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 1
|
| Now one would assume that the IRR is cleared after the INIT reset, but this
| happens only on CPU0.
|
| Why?
|
| Because our CPU0 hotplug is just for testing to make sure nothing breaks
| and goes through an NMI wakeup vehicle because INIT would send it through
| the boots-trap code which is not really working if that CPU was not
| physically unplugged.
|
| Now looking at a real world APIC the situation in that case is:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 0
|
| Why?
|
| Once the dying CPU reenables interrupts the pending interrupt gets
| delivered as a spurious interupt and then the state is clear.
|
| While that CPU0 hotplug test case is surely an esoteric issue, the APIC
| emulation is still wrong, Even if the play_dead() code would not enable
| interrupts then the pending IRR bit would turn into an ISR .. interrupt
| when the APIC is reenabled on startup.
From SDM 10.4.7.2 Local APIC State After It Has Been Software Disabled
* Pending interrupts in the IRR and ISR registers are held and require
masking or handling by the CPU.
In Thomas's testing, hardware cpu will not respect soft disable LAPIC
when IRR has already been set or APICv posted-interrupt is in flight,
so we can skip soft disable APIC checking when clearing IRR and set ISR,
continue to respect soft disable APIC when attempting to set IRR.
Reported-by: Rong Chen <[email protected]>
Reported-by: Feng Tang <[email protected]>
Reported-by: Thomas Gleixner <[email protected]>
Tested-by: Thomas Gleixner <[email protected]>
Cc: Paolo Bonzini <[email protected]>
Cc: Radim Krčmář <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Rong Chen <[email protected]>
Cc: Feng Tang <[email protected]>
Cc: [email protected]
Signed-off-by: Wanpeng Li <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
Currently KVM_STATE_NESTED_EVMCS is used to signal that eVMCS
capability is enabled on vCPU.
As indicated by vmx->nested.enlightened_vmcs_enabled.
This is quite bizarre as userspace VMM should make sure to expose
same vCPU with same CPUID values in both source and destination.
In case vCPU is exposed with eVMCS support on CPUID, it is also
expected to enable KVM_CAP_HYPERV_ENLIGHTENED_VMCS capability.
Therefore, KVM_STATE_NESTED_EVMCS is redundant.
KVM_STATE_NESTED_EVMCS is currently used on restore path
(vmx_set_nested_state()) only to enable eVMCS capability in KVM
and to signal need_vmcs12_sync such that on next VMEntry to guest
nested_sync_from_vmcs12() will be called to sync vmcs12 content
into eVMCS in guest memory.
However, because restore nested-state is rare enough, we could
have just modified vmx_set_nested_state() to always signal
need_vmcs12_sync.
From all the above, it seems that we could have just removed
the usage of KVM_STATE_NESTED_EVMCS. However, in order to preserve
backwards migration compatibility, we cannot do that.
(vmx_get_nested_state() needs to signal flag when migrating from
new kernel to old kernel).
Returning KVM_STATE_NESTED_EVMCS when just vCPU have eVMCS enabled
have a bad side-effect of userspace VMM having to send nested-state
from source to destination as part of migration stream. Even if
guest have never used eVMCS as it doesn't even run a nested
hypervisor workload. This requires destination userspace VMM and
KVM to support setting nested-state. Which make it more difficult
to migrate from new host to older host.
To avoid this, change KVM_STATE_NESTED_EVMCS to signal eVMCS is
not only enabled but also active. i.e. Guest have made some
eVMCS active via an enlightened VMEntry. i.e. vmcs12 is copied
from eVMCS and therefore should be restored into eVMCS resident
in memory (by copy_vmcs12_to_enlightened()).
Reviewed-by: Vitaly Kuznetsov <[email protected]>
Reviewed-by: Maran Wilson <[email protected]>
Reviewed-by: Krish Sadhukhan <[email protected]>
Signed-off-by: Liran Alon <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
As comment in code specifies, SMM temporarily disables VMX so we cannot
be in guest mode, nor can VMLAUNCH/VMRESUME be pending.
However, code currently assumes that these are the only flags that can be
set on kvm_state->flags. This is not true as KVM_STATE_NESTED_EVMCS
can also be set on this field to signal that eVMCS should be enabled.
Therefore, fix code to check for guest-mode and pending VMLAUNCH/VMRESUME
explicitly.
Reviewed-by: Joao Martins <[email protected]>
Signed-off-by: Liran Alon <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
This warning can be triggered easily by userspace, so it should certainly not
cause a panic if panic_on_warn is set.
Reported-by: [email protected]
Suggested-by: Alexander Potapenko <[email protected]>
Acked-by: Alexander Potapenko <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
The fixed regulator driver doesn't specify any con_id for gpio lookup
so it must be NULL in the table entry.
Fixes: 274e4c336192 ("ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx")
Cc: [email protected]
Signed-off-by: Bartosz Golaszewski <[email protected]>
Signed-off-by: Sekhar Nori <[email protected]>
|
|
We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 1d272894ec4f ("ARM: davinci: omapl138-hawk: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <[email protected]>
Signed-off-by: Sekhar Nori <[email protected]>
|
|
We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 274e4c336192 ("ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <[email protected]>
Signed-off-by: Sekhar Nori <[email protected]>
|
|
AP Queue Interruption Control (AQIC) facility gives
the guest the possibility to control interruption for
the Cryptographic Adjunct Processor queues.
Signed-off-by: Pierre Morel <[email protected]>
Reviewed-by: Tony Krowiak <[email protected]>
Acked-by: Harald Freudenberger <[email protected]>
Acked-by: Christian Borntraeger <[email protected]>
Signed-off-by: Halil Pasic <[email protected]>
[ Modified while picking: we may not expose STFLE facility 65
unconditionally because AIV is a pre-requirement.]
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
We register a AP PQAP instruction hook during the open
of the mediated device. And unregister it on release.
During the probe of the AP device, we allocate a vfio_ap_queue
structure to keep track of the information we need for the
PQAP/AQIC instruction interception.
In the AP PQAP instruction hook, if we receive a demand to
enable IRQs,
- we retrieve the vfio_ap_queue based on the APQN we receive
in REG1,
- we retrieve the page of the guest address, (NIB), from
register REG2
- we retrieve the mediated device to use the VFIO pinning
infrastructure to pin the page of the guest address,
- we retrieve the pointer to KVM to register the guest ISC
and retrieve the host ISC
- finaly we activate GISA
If we receive a demand to disable IRQs,
- we deactivate GISA
- unregister from the GIB
- unpin the NIB
When removing the AP device from the driver the device is
reseted and this process unregisters the GISA from the GIB,
and unpins the NIB address then we free the vfio_ap_queue
structure.
Signed-off-by: Pierre Morel <[email protected]>
Acked-by: Tony Krowiak <[email protected]>
Acked-by: Harald Freudenberger <[email protected]>
Signed-off-by: Halil Pasic <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
To be able to use the VFIO interface to facilitate the
mediated device memory pinning/unpinning we need to register
a notifier for IOMMU.
While we will start to pin one guest page for the interrupt indicator
byte, this is still ok with ballooning as this page will never be
used by the guest virtio-balloon driver.
So the pinned page will never be freed. And even a broken guest does
so, that would not impact the host as the original page is still
in control by vfio.
Signed-off-by: Pierre Morel <[email protected]>
Reviewed-by: Cornelia Huck <[email protected]>
Reviewed-by: Tony Krowiak <[email protected]>
Acked-by: Harald Freudenberger <[email protected]>
Signed-off-by: Halil Pasic <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
We prepare the interception of the PQAP/AQIC instruction for
the case the AQIC facility is enabled in the guest.
First of all we do not want to change existing behavior when
intercepting AP instructions without the SIE allowing the guest
to use AP instructions.
In this patch we only handle the AQIC interception allowed by
facility 65 which will be enabled when the complete interception
infrastructure will be present.
We add a callback inside the KVM arch structure for s390 for
a VFIO driver to handle a specific response to the PQAP
instruction with the AQIC command and only this command.
But we want to be able to return a correct answer to the guest
even there is no VFIO AP driver in the kernel.
Therefor, we inject the correct exceptions from inside KVM for the
case the callback is not initialized, which happens when the vfio_ap
driver is not loaded.
We do consider the responsibility of the driver to always initialize
the PQAP callback if it defines queues by initializing the CRYCB for
a guest.
If the callback has been setup we call it.
If not we setup an answer considering that no queue is available
for the guest when no callback has been setup.
Signed-off-by: Pierre Morel <[email protected]>
Reviewed-by: Tony Krowiak <[email protected]>
Acked-by: Harald Freudenberger <[email protected]>
Acked-by: Christian Borntraeger <[email protected]>
Signed-off-by: Halil Pasic <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
Kasan instrumentation of backchain unwinder stack reads is disabled
completely and simply uses READ_ONCE_NOCHECK now.
READ_ONCE_TASK_STACK macro is unused and could be removed.
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
Avoid kasan false positive when current task is interrupted in-between
stack frame allocation and backchain write instructions leaving new stack
frame backchain invalid. In particular if backchain is 0 the unwinder
tries to read pt_regs from the stack and might hit kasan poisoned bytes,
leading to kasan "stack-out-of-bounds" report.
Disable kasan instrumentation of unwinder stack reads, since this
limitation couldn't be handled otherwise with current backchain unwinder
implementation.
Fixes: 78c98f907413 ("s390/unwind: introduce stack unwind API")
Reported-by: Julian Wiedmann <[email protected]>
Tested-by: Benjamin Block <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
Current code sets the dsci to 0x00000080. Which doesn't make any sense,
as the indicator area is located in the _left-most_ byte.
Worse: if the dsci is the _shared_ indicator, this potentially clears
the indication of activity for a _different_ device.
tiqdio_thinint_handler() will then have no reason to call that device's
IRQ handler, and the device ends up stalling.
Fixes: d0c9d4a89fff ("[S390] qdio: set correct bit in dsci")
Cc: <[email protected]>
Signed-off-by: Julian Wiedmann <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
When tiqdio_remove_input_queues() removes a queue from the tiq_list as
part of qdio_shutdown(), it doesn't re-initialize the queue's list entry
and the prev/next pointers go stale.
If a subsequent qdio_establish() fails while sending the ESTABLISH cmd,
it calls qdio_shutdown() again in QDIO_IRQ_STATE_ERR state and
tiqdio_remove_input_queues() will attempt to remove the queue entry a
second time. This dereferences the stale pointers, and bad things ensue.
Fix this by re-initializing the list entry after removing it from the
list.
For good practice also initialize the list entry when the queue is first
allocated, and remove the quirky checks that papered over this omission.
Note that prior to
commit e521813468f7 ("s390/qdio: fix access to uninitialized qdio_q fields"),
these checks were bogus anyway.
setup_queues_misc() clears the whole queue struct, and thus needs to
re-init the prev/next pointers as well.
Fixes: 779e6e1c724d ("[S390] qdio: new qdio driver.")
Cc: <[email protected]>
Signed-off-by: Julian Wiedmann <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
The "len" variable is the length of the option up to the next option or
to the end of the string which ever first. We want to print the invalid
option so we want precision "%.*s" but the format is width "%*s" so it
prints up to the end of the string.
Signed-off-by: Dan Carpenter <[email protected]>
Tested-by: Stefan Haberland <[email protected]>
Signed-off-by: Stefan Haberland <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
Sometimes, we want to control which of the matching drivers
binds to a subchannel device (e.g. for subchannels we want to
handle via vfio-ccw).
For pci devices, a mechanism to do so has been introduced in
782a985d7af2 ("PCI: Introduce new device binding path using
pci_dev.driver_override"). It makes sense to introduce the
driver_override attribute for subchannel devices as well, so
that we can easily extend the 'driverctl' tool (which makes
use of the driver_override attribute for pci).
Note that unlike pci we still require a driver override to
match the subchannel type; matching more than one subchannel
type is probably not useful anyway.
Signed-off-by: Cornelia Huck <[email protected]>
Reviewed-by: Halil Pasic <[email protected]>
Reviewed-by: Sebastian Ott <[email protected]>
Signed-off-by: Sebastian Ott <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
|
|
Despite what I think the prm recommends, commit f2253bd9859b
("drm/i915/ringbuffer: EMIT_INVALIDATE after switch context") turned out
to be a huge mistake when enabling Ironlake contexts as the GPU would
hang on either a MI_FLUSH or PIPE_CONTROL immediately following the
MI_SET_CONTEXT of an active mesa context (more vanilla contexts, e.g.
simple rendercopies with igt, do not suffer).
Ville found the following clue,
"[DevCTG+]: For the invalidate operation of the pipe control, the
following pointers are affected. The
invalidate operation affects the restore of these packets. If the pipe
control invalidate operation is completed
before the context save, the indirect pointers will not be restored from
memory.
1. Pipeline State Pointer
2. Media State Pointer
3. Constant Buffer Packet"
which suggests by us emitting the INVALIDATE prior to the MI_SET_CONTEXT,
we prevent the context-restore from chasing the dangling pointers within
the image, and explains why this likely prevents the GPU hang.
Signed-off-by: Chris Wilson <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 928f8f42310f244501a7c70daac82c196112c190 in drm-intel-next)
Cc: [email protected]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111014
Fixes: f2253bd9859b ("drm/i915/ringbuffer: EMIT_INVALIDATE after switch context")
Signed-off-by: Daniel Vetter <[email protected]>
|
|
paranoid_exit needs to restore CR3 before GSBASE. Doing it in the opposite
order crashes if the exception came from a context with user GSBASE and
user CR3 -- RESTORE_CR3 cannot resture user CR3 if run with user GSBASE.
This results in infinitely recursing exceptions if user code does SYSENTER
with TF set if both FSGSBASE and PTI are enabled.
The old code worked if user code just set TF without SYSENTER because #DB
from user mode is special cased in idtentry and paranoid_exit doesn't run.
Fix it by cleaning up the spaghetti code. All that paranoid_exit needs to
do is to disable IRQs, handle IRQ tracing, then restore CR3, and restore
GSBASE. Simply do those actions in that order.
Fixes: 708078f65721 ("x86/entry/64: Handle FSGSBASE enabled paranoid entry/exit")
Reported-by: Vegard Nossum <[email protected]>
Signed-off-by: Chang S. Bae <[email protected]>
Signed-off-by: Andy Lutomirski <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: "H . Peter Anvin" <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Ravi Shankar <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Link: https://lkml.kernel.org/r/59725ceb08977359489fbed979716949ad45f616.1562035429.git.luto@kernel.org
|
|
It's only used if !CONFIG_IA32_EMULATION, so disable it in normal
configs. This will save a few bytes of text and reduce confusion.
Signed-off-by: Andy Lutomirski <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: "BaeChang Seok" <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: "Bae, Chang Seok" <[email protected]>
Link: https://lkml.kernel.org/r/0f7dafa72fe7194689de5ee8cfe5d83509fabcf5.1562035429.git.luto@kernel.org
|
|
Make sure that both variants of the nasty TF-in-compat-syscall are
exercised regardless of what vendor's CPU is running the tests.
Also change the intentional signal after SYSCALL to use ud2, which
is a lot more comprehensible.
This crashes the kernel due to an FSGSBASE bug right now.
This test *also* detects a bug in KVM when run on an Intel host. KVM
people, feel free to use it to help debug. There's a bunch of code in this
test to warn instead of going into an infinite looping when the bug gets
triggered.
Reported-by: Vegard Nossum <[email protected]>
Signed-off-by: Andy Lutomirski <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: "BaeChang Seok" <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Paolo Bonzini <[email protected]>
Cc: [email protected]
Cc: "Bae, Chang Seok" <[email protected]>
Link: https://lkml.kernel.org/r/5f5de10441ab2e3005538b4c33be9b1965d1bb63.1562035429.git.luto@kernel.org
|
|
Fix sparse warnings:
lib/reed_solomon/test_rslib.c:313:5: warning: symbol 'ex_rs_helper' was not declared. Should it be static?
lib/reed_solomon/test_rslib.c:349:5: warning: symbol 'exercise_rs' was not declared. Should it be static?
lib/reed_solomon/test_rslib.c:407:5: warning: symbol 'exercise_rs_bc' was not declared. Should it be static?
Reported-by: Hulk Robot <[email protected]>
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
The irqchip driver depends on the SoC specific driver, but we want
to be able to compile-test it elsewhere:
WARNING: unmet direct dependencies detected for TI_SCI_INTA_MSI_DOMAIN
Depends on [n]: SOC_TI [=n]
Selected by [y]:
- TI_SCI_INTA_IRQCHIP [=y] && TI_SCI_PROTOCOL [=y]
drivers/irqchip/irq-ti-sci-inta.o: In function `ti_sci_inta_irq_domain_probe':
irq-ti-sci-inta.c:(.text+0x204): undefined reference to `ti_sci_inta_msi_create_irq_domain'
Rearrange the Kconfig and Makefile so we build the soc driver whenever
its users are there, regardless of the SOC_TI option.
Fixes: 49b323157bf1 ("soc: ti: Add MSI domain bus support for Interrupt Aggregator")
Fixes: f011df6179bd ("irqchip/ti-sci-inta: Add msi domain support")
Signed-off-by: Arnd Bergmann <[email protected]>
Reviewed-by: Lokesh Vutla <[email protected]>
Acked-by: Santosh Shilimkar <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
arm/fixes
mvebu fixes for 5.2 (part 2)
Use the armada-38x-uart compatible strings for Armada XP 98dx3236 SoCs
in order to not loose character anymore.
* tag 'mvebu-fixes-5.2-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-xp-98dx3236: Switch to armada-38x-uart serial node
Signed-off-by: Olof Johansson <[email protected]>
|
|
The widget_mutex was introduced to serialize callers to
hda_widget_sysfs_{re}init. However, its protection of the sysfs widget array
is incomplete. For example, it is acquired around the call to
hda_widget_sysfs_reinit(), which actually creates the new array, but isn't
still acquired when codec->num_nodes and codec->start_nid is updated. So
the lock ensures one thread sets up the new array at a time, but doesn't
ensure which thread's value will end up in codec->num_nodes. If a larger
num_nodes wins but a smaller array was set up, the next call to
refresh_widgets() will touch free memory as it iterates over codec->num_nodes
that aren't there.
The widget_lock really protects both the tree as well as codec->num_nodes,
start_nid, and end_nid, so make sure it's held across that update. It should
also be held during snd_hdac_get_sub_nodes(), so that a very old read from that
function doesn't end up clobbering a later update.
Fixes: ed180abba7f1 ("ALSA: hda: Fix race between creating and refreshing sysfs entries")
Signed-off-by: Evan Green <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Recommended by the hw team.
Reviewed-and-Tested-by: Huang Rui <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
In IEC 61883-6, 8 MIDI data streams are multiplexed into single
MIDI conformant data channel. The index of stream is calculated by
modulo 8 of the value of data block counter.
In fireworks, the value of data block counter in CIP header has a quirk
with firmware version v5.0.0, v5.7.3 and v5.8.0. This brings ALSA
IEC 61883-1/6 packet streaming engine to miss detection of MIDI
messages.
This commit fixes the miss detection to modify the value of data block
counter for the modulo calculation.
For maintainers, this bug exists since a commit 18f5ed365d3f ("ALSA:
fireworks/firewire-lib: add support for recent firmware quirk") in Linux
kernel v4.2. There're many changes since the commit. This fix can be
backported to Linux kernel v4.4 or later. I tagged a base commit to the
backport for your convenience.
Besides, my work for Linux kernel v5.3 brings heavy code refactoring and
some structure members are renamed in 'sound/firewire/amdtp-stream.h'.
The content of this patch brings conflict when merging -rc tree with
this patch and the latest tree. I request maintainers to solve the
conflict to replace 'tx_first_dbc' with 'ctx_data.tx.first_dbc'.
Fixes: df075feefbd3 ("ALSA: firewire-lib: complete AM824 data block processing layer")
Cc: <[email protected]> # v4.4+
Signed-off-by: Takashi Sakamoto <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/will/linux
* 'for-next/perf' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux:
perf: arm_spe: Enable ACPI/Platform automatic module loading
arm_pmu: acpi: spe: Add initial MADT/SPE probing
ACPI/PPTT: Add function to return ACPI 6.3 Identical tokens
ACPI/PPTT: Modify node flag detection to find last IDENTICAL
MAINTAINERS: Add maintainer entry for the imx8 DDR PMU driver
drivers/perf: imx_ddr: Add DDR performance counter support to perf
dt-bindings: perf: imx8-ddr: add imx8qxp ddr performance monitor
|
|
sys_move_mount() crashes by dereferencing the pointer MNT_NS_INTERNAL,
a.k.a. ERR_PTR(-EINVAL), if the old mount is specified by fd for a
kernel object with an internal mount, such as a pipe or memfd.
Fix it by checking for this case and returning -EINVAL.
[AV: what we want is is_mounted(); use that instead of making the
condition even more convoluted]
Reproducer:
#include <unistd.h>
#define __NR_move_mount 429
#define MOVE_MOUNT_F_EMPTY_PATH 0x00000004
int main()
{
int fds[2];
pipe(fds);
syscall(__NR_move_mount, fds[0], "", -1, "/", MOVE_MOUNT_F_EMPTY_PATH);
}
Reported-by: [email protected]
Fixes: 2db154b3ea8e ("vfs: syscall: Add move_mount(2) to move mounts around")
Signed-off-by: Eric Biggers <[email protected]>
Signed-off-by: Al Viro <[email protected]>
|
|
Make sure to return a proper negative error code from copy_process()
when anon_inode_getfile() fails with CLONE_PIDFD.
Otherwise _do_fork() will not detect an error and get_task_pid() will
operator on a nonsensical pointer:
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000006dbc2c
R13: 00007ffc15fbb0ff R14: 00007ff07e47e9c0 R15: 0000000000000000
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 7990 Comm: syz-executor290 Not tainted 5.2.0-rc6+ #9
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:__read_once_size include/linux/compiler.h:194 [inline]
RIP: 0010:get_task_pid+0xe1/0x210 kernel/pid.c:372
Code: 89 ff e8 62 27 5f 00 49 8b 07 44 89 f1 4c 8d bc c8 90 01 00 00 eb 0c
e8 0d fe 25 00 49 81 c7 38 05 00 00 4c 89 f8 48 c1 e8 03 <80> 3c 18 00 74
08 4c 89 ff e8 31 27 5f 00 4d 8b 37 e8 f9 47 12 00
RSP: 0018:ffff88808a4a7d78 EFLAGS: 00010203
RAX: 00000000000000a7 RBX: dffffc0000000000 RCX: ffff888088180600
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88808a4a7d90 R08: ffffffff814fb3a8 R09: ffffed1015d66bf8
R10: ffffed1015d66bf8 R11: 1ffff11015d66bf7 R12: 0000000000041ffc
R13: 1ffff11011494fbc R14: 0000000000000000 R15: 000000000000053d
FS: 00007ff07e47e700(0000) GS:ffff8880aeb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004b5100 CR3: 0000000094df2000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
_do_fork+0x1b9/0x5f0 kernel/fork.c:2360
__do_sys_clone kernel/fork.c:2454 [inline]
__se_sys_clone kernel/fork.c:2448 [inline]
__x64_sys_clone+0xc1/0xd0 kernel/fork.c:2448
do_syscall_64+0xfe/0x140 arch/x86/entry/common.c:301
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Link: https://lore.kernel.org/lkml/[email protected]
Reported-and-tested-by: [email protected]
Fixes: 6fd2fe494b17 ("copy_process(): don't use ksys_close() on cleanups")
Cc: Jann Horn <[email protected]>
Cc: Al Viro <[email protected]>
Signed-off-by: Christian Brauner <[email protected]>
|
|
I'm not entirely sure why this is, but for some reason:
921935dc6404 ("drm/amd/powerplay: enforce display related settings only on needed")
Breaks runtime PM resume on the Radeon PRO WX 3100 (Lexa) in one the
pre-production laptops I have. The issue manifests as the following
messages in dmesg:
[drm] UVD and UVD ENC initialized successfully.
amdgpu 0000:3b:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring vce1 test failed (-110)
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block <vce_v3_0> failed -110
[drm:amdgpu_device_resume [amdgpu]] *ERROR* amdgpu_device_ip_resume failed (-110).
And happens after about 6-10 runtime PM suspend/resume cycles (sometimes
sooner, if you're lucky!). Unfortunately I can't seem to pin down
precisely which part in psm_adjust_power_state_dynamic that is causing
the issue, but not skipping the display setting setup seems to fix it.
Hopefully if there is a better fix for this, this patch will spark
discussion around it.
Fixes: 921935dc6404 ("drm/amd/powerplay: enforce display related settings only on needed")
Cc: Evan Quan <[email protected]>
Cc: Alex Deucher <[email protected]>
Cc: Huang Rui <[email protected]>
Cc: Rex Zhu <[email protected]>
Cc: Likun Gao <[email protected]>
Cc: <[email protected]> # v5.1+
Signed-off-by: Lyude Paul <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Otherwise, you may get divided-by-zero error or corrput the SMU fan
control feature.
Signed-off-by: Evan Quan <[email protected]>
Reviewed-by: Alex Deucher <[email protected]>
Tested-by: Slava Abramov <[email protected]>
Acked-by: Slava Abramov <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
If MTD_NAND_JZ4780 is y and MTD_NAND_JZ4780_BCH is m,
which select CONFIG_MTD_NAND_INGENIC_ECC to m, building fails:
drivers/mtd/nand/raw/ingenic/ingenic_nand.o: In function `ingenic_nand_remove':
ingenic_nand.c:(.text+0x177): undefined reference to `ingenic_ecc_release'
drivers/mtd/nand/raw/ingenic/ingenic_nand.o: In function `ingenic_nand_ecc_correct':
ingenic_nand.c:(.text+0x2ee): undefined reference to `ingenic_ecc_correct'
To fix that, the ingenic_nand and ingenic_ecc modules have been fused
into one single module.
- The ingenic_ecc.c code is now compiled in only if
$(CONFIG_MTD_NAND_INGENIC_ECC) is set. This is now a boolean instead
of tristate.
- To avoid changing the module name, the ingenic_nand.c file is moved to
ingenic_nand_drv.c. Then the module name is still ingenic_nand.
- Since ingenic_ecc.c is no more a module, the module-specific macros
have been dropped, and the functions are no more exported for use by
the ingenic_nand driver.
Fixes: 15de8c6efd0e ("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Paul Cercueil <[email protected]>
Reported-by: Arnd Bergmann <[email protected]>
Reported-by: Hulk Robot <[email protected]>
Cc: YueHaibing <[email protected]>
Cc: [email protected]
Signed-off-by: Miquel Raynal <[email protected]>
|
|
The 1Gb Macronix chip can have a maximum of 20 bad blocks, while
the 2Gb version has twice as many blocks and therefore the maximum
number of bad blocks is 40.
The 4Gb GigaDevice GD5F4GQ4xA has twice as many blocks as its 2Gb
counterpart and therefore a maximum of 80 bad blocks.
Fixes: 377e517b5fa5 ("mtd: nand: Add max_bad_eraseblocks_per_lun info to memorg")
Reported-by: Emil Lenngren <[email protected]>
Signed-off-by: Frieder Schrempf <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
|
|
When we remap memory as non-cached, to be used as a DMA coherent buffer,
we should writeback all cache and invalidate the cache lines so that we
make sure we have a clean slate. Implement this using the cache_push()
helper.
Signed-off-by: Christoph Hellwig <[email protected]>
Signed-off-by: Geert Uytterhoeven <[email protected]>
|